Download - Hvac Reference Data Guide
-
8/13/2019 Hvac Reference Data Guide
1/79
HVAC
Reference Data Guide
Versi on 2007 (7.0) January 2007 DSP3D-PE-200018G
-
8/13/2019 Hvac Reference Data Guide
2/79
CopyrightCopyright 2002-2007, Intergraph Corporation. All Rights Reserved.
Including software, file formats, and audiovisual displays; may be used pursuant to applicable software license
agreement; contains confidential and proprietary information of Intergraph and/or third parties which is protected by
copyright law, trade secret law, and international treaty, and may not be provided or otherwise made available
without proper authorization.
Portions of this software are owned by Spatial Corp. 1986-2007. All Rights Reserved.
Restricted Rights Legend
Use, duplication, or disclosure by the government is subject to restrictions as set forth below. For civilian agencies:
This was developed at private expense and is restricted computer software submitted with restricted rights inaccordance with subparagraphs (a) through (d) of the Commercial Computer Software - Restricted Rights clause at
52.227-19 of the Federal Acquisition Regulations (FAR) and its successors, and is unpublished and all rights are
reserved under the copyright laws of the United States. For units of the Department of Defense (DoD): This iscommercial computer software as defined at DFARS 252.227-7014 and the rights of the Government are as
specified at DFARS 227.7202-3.
Unpublished rights reserved under the copyright laws of the United States.
Intergraph Corporation
Huntsville, Alabama 35894-0001
Warranties and Liabilities
All warranties given by Intergraph Corporation about equipment or software are set forth in your purchase contract,
and nothing stated in, or implied by, this document or its contents shall be considered or deemed a modification or
amendment of such warranties. Intergraph believes the information in this publication is accurate as of its
publication date.
The information and the software discussed in this document are subject to change without notice and are subject toapplicable technical product descriptions. Intergraph Corporation is not responsible for any error that may appear in
this document.
The software discussed in this document is furnished under a license and may be used or copied only in accordance
with the terms of this license.No responsibility is assumed by Intergraph for the use or reliability of software on equipment that is not supplied by
Intergraph or its affiliated companies. THE USER OF THE SOFTWARE IS EXPECTED TO MAKE THE FINALEVALUATION AS TO THE USEFULNESS OF THE SOFTWARE IN HIS OWN ENVIRONMENT.
Intergraph is not responsible for the accuracy of delivered data including, but not limited to, catalog, reference and
symbol data. Users should verify for themselves that the data is accurate and suitable for their project work.
Trademarks
Intergraph, the Intergraph logo, SmartSketch, FrameWorks, SmartPlant, IntelliShip, INtools, ISOGEN, PDS, and
MARIAN are registered trademarks of Intergraph Corporation. Microsoft and Windows are registered trademarks of
Microsoft Corporation. ACIS is a registered trademark of SPATIAL TECHNOLOGY, INC. Infragistics,Presentation Layer Framework, ActiveTreeView Ctrl, ProtoViewCtl, ActiveThreed Ctrl, ActiveListBar Ctrl,
ActiveSplitter, ActiveToolbars Ctrl, ActiveToolbars Plus Ctrl, and ProtoView are trademarks of Infragistics, Inc.Portions of 2D DCM, 3D DCM, and HLM from D-Cubed Limited are incorporated. All rights reserved. Oracle, JD
Edwards, PeopleSoft, and Retek are registered trademarks of Oracle Corporation and/or its affiliates. Other brands
and product names are trademarks of their respective owners.
-
8/13/2019 Hvac Reference Data Guide
3/79
Table of Contents
HVAC Reference Data Guide 3
Table of Contents
Preface.................................................................................................................................5
SmartPlant 3D Documentation Set...............................................................................6Administrative Guides ........................................................................................................ 6User's Guides ...................................................................................................................... 7Reference Data Guides ....................................................................................................... 8ISOGEN Guides ................................................................................................................. 9
Documentation Comments .........................................................................................10
What's New in HVAC Reference Data.......................................................................11
HVAC Reference Data: An Overview............................................................................12
HVAC Sheets: An Overview...........................................................................................13
HVACSpec Sheet ............................................................................................................. 15ManualDamper Sheet........................................................................................................ 19MotorDamper Sheet.......................................................................................................... 22Rect_FlatFlange Sheet ...................................................................................................... 24Round_FlatFlange Sheet................................................................................................... 26Rect_FlatFlangeVA Sheet ................................................................................................ 28Round_FlatFlangeVA Sheet ............................................................................................. 30Round_Sleeve Sheet ......................................................................................................... 32Rect_Sleeve Sheet............................................................................................................. 34Round_Weld Sheet ........................................................................................................... 36Rect_Weld Sheet............................................................................................................... 37Round_Rivet Sheet ........................................................................................................... 39
Rect_Rivet Sheet............................................................................................................... 40FlatOval_Weld Sheet ........................................................................................................ 42FlatOval_Rivet Sheet ........................................................................................................ 43DuctSmokeDetector Sheet ................................................................................................ 45SamplingTube Sheet ......................................................................................................... 46Horn_Strobe Sheet ............................................................................................................ 47SurfMountIcover Sheet..................................................................................................... 48SM1PipingTap Sheet ........................................................................................................ 50SMRoundBranch Sheet..................................................................................................... 52SMRectangularBranch Sheet ............................................................................................ 53RoundTee Sheet ................................................................................................................ 54RectTee Sheet ...................................................................................................................56
HVACElbow Sheet........................................................................................................... 58RoundElbow Sheet............................................................................................................ 60HsqrThroatElbow Sheet.................................................................................................... 62BellMouthRound Sheet..................................................................................................... 64BellMouthRFO Sheet ....................................................................................................... 65Division2 Sheet................................................................................................................. 66DivisionW3 Sheet ............................................................................................................. 68AirFilter Sheet................................................................................................................... 70AirFilterHumidifier Sheet................................................................................................. 72
-
8/13/2019 Hvac Reference Data Guide
4/79
Table of Contents
4 HVAC Reference Data Guide
AirCoolingCoil Sheet........................................................................................................ 74HvacSpecDefaults Sheet................................................................................................... 76PermissibleDuctThickness Sheet ...................................................................................... 78
Index..................................................................................................................................79
-
8/13/2019 Hvac Reference Data Guide
5/79
Preface
HVAC Reference Data Guide 5
PrefaceThis document is a reference data guide for the SmartPlant 3D HVAC task. The
purpose of this document is to describe the reference data delivered with the software
for this task.
Reference data includes both catalog data and specification data. Catalog dataincludes the parts that you place in the model, such as piping components and
equipment. Specification data includes the rules that govern how those parts are
placed and connected.
-
8/13/2019 Hvac Reference Data Guide
6/79
Preface
6 HVAC Reference Data Guide
SmartPlant 3D Documentation Set
The SmartPlant3D documentation set is available as Adobe
PDF files. The content
of the PDF files is the same content as online Help. To access these PDF documents
in the software, click Help > Printable Guides.
The documentation set is divided into four categories:
Administrative guides contain information about installing, configuring,customizing, and troubleshooting SmartPlant 3D.
User's guides provide command reference and how-to information forworking in each SmartPlant 3D task.
Reference data guides define the reference data workbooks. Not all taskshave reference data.
ISOGEN guides
Administrative Guides
Project Management User's Guide - Provides instructions for setting up the
databases, creating permission groups, backing up and restoring project data,assigning access permissions to the model, managing interference detection, defining
and managing locations for Global Workshare, controlling duplication and
consolidation of plants, tools for synchronization, regeneration of report databases,
and version upgrade.
SmartPlant 3D Database Integrity Guide- Provides information about the error
messages in the database integrity reports, including meaning, cause, and possible
corrective action.
SmartPlant 3D Global Workshare Guide- Provides instructions for setting up the
software and the databases to work in a workshare environment.
SmartPlant 3D Installation Guide- Provides instructions on installing and
configuring the software on both the client and server computers.
SmartPlant 3D/IntelliShip Programmer's Guide- Provides information about custom
commands, naming rules, and symbol programming.
SmartPlant 3D Integration Reference Guide- Provides information about installing,
configuring, and using SmartPlant 3D in an integrated environment.
SmartPlant 3D Interference Checking Guide- Provides information on installing,
configuring, and using the interference detection service.
-
8/13/2019 Hvac Reference Data Guide
7/79
Preface
HVAC Reference Data Guide 7
SmartPlant 3D Interpreting Human Piping Specifications- Provides information
about how to interpret human piping specifications so that you can create the
corresponding piping specification in the software.
SmartPlant 3D Plant Design System (PDS) Guide- Provides all information needed
to use PDS with SmartPlant 3D. Topics include referencing active PDS projects inSmartPlant 3D, exporting PDS data and importing that data into SmartPlant 3D,
converting PDS reference data to SmartPlant 3D reference data, and converting
EDEN symbols to Visual Basic symbols.
SmartPlant 3D Release Bulletin- Provides what's new, hardware/software
requirements, and support information for the current release.
SmartPlant 3D Troubleshooting Guide- Provides information on how to resolve
errors that you may encounter in the software by documenting troubleshooting tips,
error messages, and to do list messages.
User's Guides
Catalog User's Guide- Provides information about viewing, editing, and creating
reference data and select lists (codelists).
Common User's Guide- Provides information about defining workspaces, navigating
in the model, precision input, filtering, manipulating views, and running reports.
Drawings and Reports User's Guide- Provides information about creating drawing
and report deliverables.
Electrical User's Guide- Provides information about routing electrical cable,
cableway, cable tray, and conduit.
Equipment and Furnishings User's Guide- Provides information about placing
equipment.
Grids User's Guide- Provides instructions for creating coordinate systems, elevation
grid planes, vertical grid planes, radial cylinders, radial planes, grid arcs, and grid
lines.
Hangers and Supports User's Guide- Provides instructions on placing piping, duct,
cableway, and conduit supports in the model.
HVAC User's Guide- Provides instructions for routing HVAC duct.
Piping User's Guide- Provides instructions for routing pipe and placing valves, taps,
and pipe joints.
Space Management User's Guide- Provides instructions for placing volumes (such as
drawing volumes, obstruction zones) in the model.
-
8/13/2019 Hvac Reference Data Guide
8/79
Preface
8 HVAC Reference Data Guide
Structural Analysis User's Guide- Provides instructions for defining loads, load
cases, load combinations, and the importing and exporting of analytical data.
Structure User's Guide- Provides instructions for placing structural members such as:
beams, columns, braces, slabs, openings, stairs, ladders, equipment foundations, and
handrails.
Systems and Specifications User's Guide- Provides instructions for creating systems
and their hierarchies and selecting which specifications are available for each system
type.
SmartPlant 2D Symbols User's Guide- Provides instructions for creating cross
section symbols.
Reference Data Guides
Drawings and Reports Reference Data Guide- Provides information about reportsreference data.
Electrical Reference Data Guide- Provides information about electrical cable,
cableway, cable tray, and conduit reference data.
Equipment and Furnishings Reference Data Guide- Provides information about
equipment reference data and name rules.
Hangers and Supports Reference Data Guide- Provides information about hangersand supports reference data.
HVAC Reference Data Guide- Provides information about HVAC reference data.
Piping Reference Data Guide- Provides information about piping reference dataincluding piping specifications, piping specification rules, piping parts, piping
symbols, and name rules.
SmartPlant 2D Symbols Reference Data Guide- Provides information about the two-
dimensional symbols used in all tasks.
SmartPlant 3D Reference Data Guide- Provides instructions about the Bulkload
utility, codelists, and the reference data common to several disciplines.
SmartPlant 3D Symbols Reference Data Guide- Provides information about theVisual Basic Part Definition Wizard and the three-dimensional symbols used in all
tasks.
Space Management Reference Data Guide- Provides information about space
management reference data.
-
8/13/2019 Hvac Reference Data Guide
9/79
Preface
HVAC Reference Data Guide 9
Structure Reference Data Guide- Provides information about structural reference
data and name rules.
ISOGEN Guides
AText Reference Guide- Provides information about alternative text for isometric
drawings. This guide is from Alias, the makers of ISOGEN
.
Option Switches Reference Guide- Provides information about the ISOGEN option
switches for isometric drawings. This guide is from Alias, the makers of ISOGEN.
Symbol Keys Reference Guide- Provides information about the symbol keys for
isometric drawings. This guide is from Alias, the makers of ISOGEN.
-
8/13/2019 Hvac Reference Data Guide
10/79
Preface
10 HVAC Reference Data Guide
Documentation Comments
Send documentation comments or suggestions to [email protected].
mailto:[email protected]?subject=Documentation%20Commentsmailto:[email protected]?subject=Documentation%20Commentsmailto:[email protected]?subject=Documentation%20Commentsmailto:[email protected]?subject=Documentation%20Comments -
8/13/2019 Hvac Reference Data Guide
11/79
Preface
HVAC Reference Data Guide 11
What's New in HVAC Reference Data
Version 2007
No changes.
-
8/13/2019 Hvac Reference Data Guide
12/79
HVAC Reference Data: An Overview
12 HVAC Reference Data Guide
HVAC Reference Data: An OverviewIn the HVAC task, reference data contains the rules and the parts necessary for
placement of routing in the duct system. These rules help in selecting the proper part
for the application and limiting parts availability based on routing conditions. HVACprovides duct-sizing capability to determine the proper duct sizes. This duct sizing
provides a list of duct cross sections and sizes valid for the specification for the
specific design criteria. A recommendation is to set preferred components as part of
the specification and as the defaults.
The HVAC software uses several standard data tables to produce correct modeling.
An administrator can add new rows to these tables or edit existing rows. After addingor editing rows, the administrator must bulk load the information into the Catalog
Database for the new information to take effect.
The interfaces for the HVAC and Cableway tasks are very similar. Reference data
determines the values that populate the various dialog boxes in both tasks. Comparedto Cableway, the values in HVAC deal more with duct components, like nozzles and
branches. For example, to create new routes, the reference data for the HVAC task
populates the New Duct Rundialog box, while the reference data for the Cableway
task populates the Create Cablewaydialog box.
The software selects default components based on your input during a session for
routing duct. For the proper configuration, the default or preferred components
include the duct cross section, duct size, duct material, material thickness or gage, and
the end or port connections.
Related Topics HVAC Sheets: An Overview, page 13
-
8/13/2019 Hvac Reference Data Guide
13/79
HVAC Sheets: An Overview
HVAC Reference Data Guide 13
HVAC Sheets: An OverviewThe HVAC.xlsworkbook contains the reference data for the HVAC task. The sheets
that are unique to HVAC.xlsare described below. For more information on common
sheets, see the SmartPlant 3D Reference Data Guideaccessible from the Help >
Printable Guidescommand.
HvacSpec- Lists the specification names of HVAC specification objects. For more
information, see theHVACSpec Sheet, page 15.
ManualDamper- Defines reference data for manual dampers. For more information,
see theManualDamper Sheet, page 19.
MotorDamper- Defines the reference data for motor dampers. For more
information, see theMotorDamper Sheet, page 22.
Rect_FlatFlange- Defines reference data for rectangular flat flanges. For moreinformation, see theRect_FlatFlange Sheet, page 24.
Round_FlatFlange- Defines reference data for round flat flanges. For more
information, see theRound_FlatFlange Sheet, page 26.
Rect_FlatFlangeVA- Defines the reference data for rectangular flat flanges with
depth inclination. For more information, see theRect_FlatFlangeVA Sheet, page 28.
Round_FlatFlangeVA- Defines the reference data for round flat flanges with depth
inclination. For more information, see theRound_FlatFlangeVA Sheet, page 30
Round_Sleeve- Defines reference data for round sleeves. For more information, seetheRound_Sleeve Sheet, page 32.
Rect_Sleeve- Defines reference data for rectangular sleeves. For more information,
see theRect_Sleeve Sheet, page 34.
Round_Weld- Defines the reference data for round welded connections. For more
information, see theRound_Weld Sheet, page 36.
Rect_Weld- Defines the reference data for rectangular welded connections. For
more information, see theRect_Weld Sheet, page 37.
Round_Rivet- Defines the reference data for round riveted connections. For moreinformation, see theRound_Rivet Sheet, page 39.
Rect_Rivet- Defines the reference data for rectangular riveted connections. For more
information, see theRect_Rivet Sheet, page 40.
FlatOval_Weld- Defines the reference data for flat oval welded connections. For
more information, see the FlatOval_Weld Sheet, page 42.
-
8/13/2019 Hvac Reference Data Guide
14/79
HVAC Sheets: An Overview
14 HVAC Reference Data Guide
FlatOval_Rivet- Defines the reference data for flat oval riveted connections. For
more information, see the FlatOval_Rivet Sheet, page 43.
DuctSmokeDetector- Defines the reference data for duct smoke detectors. For more
information, see theDuctSmokeDetector Sheet, page 45.
SamplingTube- Defines the reference data for sampling tubes. For moreinformation, see the SamplingTube Sheet, page 46.
Horn_Strobe- Defines the reference data for visible and audible warning signals.
For more information, see theHorn_Strobe Sheet, page 47.
SurfMountIcover- Defines reference data for surface-mounted covers. For more
information, see the SurfMountIcover Sheet, page 48.
SM1PipingTap- Defines reference data for one surface-mounted piping tap on an
HVAC duct for instrument assembly. Halfin is one-half inch nominal pipe diameter.
The part can be a piping 0.5" piping tap that is either socket- welded or female-threaded. The tap is mounted on a duct surface. For more information, see theSM1PipingTap Sheet, page 50.
SMRoundBranch- Defines the reference data for a surface-mounted round branch.
For more information, see the SMRoundBranch Sheet, page 52.
SMRectangularBranch- Defines the reference data for a surface-mounted
rectangular branch. For more information, see the SMRectangularBranch Sheet, page
53.
RoundTee- Defines reference data for round tees. For more information, see the
RoundTee Sheet, page 54.
RectTee- Defines the reference data for rectangular tees. For more information, see
theRectTee Sheet, page 56.
HVACElbow- Defines reference data for HVAC elbows. For more information, see
theHVACElbow Sheet, page 58.
RoundElbow- Defines the reference data for round elbows. For more information,
see theRoundElbow Sheet, page 60.
HsqrThroatElbow- Defines the reference data for square throat elbows. For more
information, see theHsqrThroatElbow Sheet, page 62.
BellMouthRound- Defines the reference data for a bell mouth. For more
information, see theBellMouthRound Sheet, page 64.
BellMouthRFO- Defines the reference data for a bell mouth with a flat oval outlet.
For more information, see theBellMouthRFO Sheet, page 65.
-
8/13/2019 Hvac Reference Data Guide
15/79
HVAC Sheets: An Overview
HVAC Reference Data Guide 15
Division2- Defines reference data for a division feature, a component that divides the
HVAC rectangular duct into two ducts along the width of the duct. The divisionfeature has three ports: the original duct port and the resulting two ducts ports. For
more information, see theDivision2 Sheet, page 66.
DivisionW3- Defines the reference data for a division feature, a component thatdivides the HVAC rectangular duct into three ducts along the width of the duct. The
division feature has four ports: the original duct port and the resulting three duct
ports. For more information, see theDivisionW3 Sheet, page 68.
AirFilter- Defines the reference data for an air filter. For more information, see theAirFilter Sheet, page 70.
AirFilterHumidifier- Defines the reference data for an air filter humidifier. For
more information, see theAirFilterHumidifier Sheet, page 72.
AirCoolingCoil- Defines the reference data for an air cooling coil. For more
information, see theAirCoolingCoil Sheet, page 74.
HvacSpecDefaults- Lists the names of the specifications that you can use while
working with the HVAC reference data. For more information, see theHvacSpecDefaults Sheet, page 76.
PermissibleDuctThickness- Defines the reference data for permissible duct
thickness. For more information, see the PermissibleDuctThickness Sheet, page 78.
Related Topics
HVAC Reference Data: An Overview, page 12
HVACSpec Sheet
The HVACSpecsheet in the HVAC.xlsworkbook defines the specifications that are
available to you for HVAC routing. Currently, the workbook contains two
specifications: Spec-0and Spec-1.
SpecName- Type the specification name of the HVAC specification objects (for
example, Spec-0).
Service- Type a description of the service for the HVACSpec object. An example is
NoService.
PressureClass- Type the pressure class of the HvacSpec object. Examples are
LowPressureand MediumPressure.
HvacPartGenerationBasis- Specifies whether breaks on the feature boundary areenabled or disabled. Type 1to disable breaks or type 2to enable breaks. Based on this
value, the software determines if the continuous feature that you are routing is
terminated in case of a spec break.
-
8/13/2019 Hvac Reference Data Guide
16/79
HVAC Sheets: An Overview
16 HVAC Reference Data Guide
LiningMaterial(Type/Grade)- Type a phrase that describes the type or grade of the
lining material.
InsulationMaterial(Type/Grade)- Type a phrase that describes the type or grade of
the insulation material.
DuctMaterial(Type/Grade)- Type a phrase that describes the type or grade of theduct material.
Note
The duct material is defined in the Materialsheet of the AllCommon.xlsfile.
Shapes- Type the name of the shape of the object. Options include Rectangular,
Round, Oval, and FlatOval.
PartNumber- Type the phrase that identifies the part number. Examples include:
PDS-100 PDS-150 PDS-200 PDS-250 PDS-300 PDS-350 PDS-400
RECTFF -Rectangular flat flange ROUNDFF- Round flat flange ROUNDSLEEVE RectSleeve- Rectangular sleeve B-100- Brepresents bend. TA-100X80- Trepresents tee. 100x80is a reducing tee. Header is
100mm diameter of the round tee, Width, Branchis 80mm to arrive atthe bend width.
HVACElbowFo DivisionW2 SM1PTapSWhalfin-Surface-mounted piping tap on a duct surface that
is socket-welded. halfinis one-half inch nominal pipe diameter
SM1PTapFThalfin- Surface-mounted piping tap on a duct surface that isfemale-threaded. halfinis one-half inch nominal pipe diameter
AirFilterHumidifier400x200x275
-
8/13/2019 Hvac Reference Data Guide
17/79
HVAC Sheets: An Overview
HVAC Reference Data Guide 17
AirFilterHumidifier300x200x225 AirFilterHumidifier400x250x275 AirFilterHumidifier250x200x200 AirCoolingCoil400x200x350 AirCoolingCoil300x200x325 AirCoolingCoil400x250x350 AirCoolingCoil250x200x300 AirFilter400x200x180 AirFilter400x200x180 AirFilter300x200x150 AirFilter400x250x180 AirFilter250x200x120 MRD-URD-100 MRD-URD-150 MRD-URD-200 MRD-URD-250 MRD-URD-300 MRD-URD-350 MRD-URD-400 Icover400x600 Icover250x400 DivisionW3-01 SM-501-N SM-501-P RWX-N SL-2000-P STS-100 STS-50 STS-25 SHP24-1575W SHP24-1575R RoundWeld RectWeld
-
8/13/2019 Hvac Reference Data Guide
18/79
HVAC Sheets: An Overview
18 HVAC Reference Data Guide
RoundRivet RectRivet FlatOvalWeld FlatOvalRivet Rect_SlopedFlange Round_SlopedFlange RectTee1 SMRectangularBranch1 SMRoundBranch1 HVACsqrThroatElbow01 Round Bellmouth 300x250 RoundxFlatOval Bellmouth 355x1450SectionName- Identifies the outfitting cross section (OCS). Examples are OCS-4X4,
OCS-6X4, OCS-8X4, OCS-6X6, OCS-10X4, OCS-8X6, OCS-7X7, OCS-14X4,OCS-8X7, OCS-16X4, OCS-10X6, OCS-8X8, OCS-9X7, OCS-12X6, OCS-10X7,
OCS-9X8, OCS-10X8, and OCS-14X6.
Note
The section name is defined in the OutfittingCrossSectionssheet of theAllCommon.xlsfile.
Related Topics
BellMouthRFO Sheet, page 65 BellMouthRound Sheet, page 64 DuctSmokeDetector Sheet, page 45 FlatOval_Rivet Sheet, page 43 FlatOval_Weld Sheet, page 42 Horn_Strobe Sheet, page 47 HsqrThroatElbow Sheet, page 62 HVAC Sheets: An Overview, page 13 HVACElbow Sheet, page 58 ManualDamper Sheet, page 19 PermissibleDuctThickness Sheet, page 78
Rect_FlatFlange Sheet, page 24 Rect_FlatFlangeVA Sheet, page 28 Rect_Rivet Sheet, page 40 Rect_Sleeve Sheet, page 34 Rect_Weld Sheet, page 37 RectTee Sheet, page 56 Round_FlatFlange Sheet, page 26 Round_FlatFlangeVA Sheet, page 30
-
8/13/2019 Hvac Reference Data Guide
19/79
HVAC Sheets: An Overview
HVAC Reference Data Guide 19
Round_Rivet Sheet, page 39 Round_Sleeve Sheet, page 32 Round_Weld Sheet, page 36 RoundElbow Sheet, page 60 RoundTee Sheet, page 54
SamplingTube Sheet, page 46 SMRectangularBranch Sheet, page 53 SMRoundBranch Sheet, page 52 SurfMountIcover Sheet, page 48
ManualDamper Sheet
The ManualDampersheet in the HVAC.xlsworkbook defines the manual dampers
that you want in the Catalog.
PartNumber- Type the part number assigned to the manual damper. The software
uses the part number at placement when the part name is automatically generated. Anexample is PDS-100.
Tip
Part numbers for manual dampers must be unique throughout the entireCatalog.
SymbolDefinition- Type the definition of the Visual Basic symbol that you arecreating for the manual damper. An example is
PDSHRoundDamper.HRoundDamper.
FaceWidth- Type the width of the face for the damper.
FaceDepth- Type the face depth for the damper.
ComponentType- Type the component type for the damper.
PartDescription- Type a description for the damper. An example is Manual
Damper Part.
DryWeight- Type a dry weight for the damper.
DrycogX- Type the offset distance along the x-axis for the dry center of gravity of
the damper.
DrycogY- Type the offset distance along the y-axis for the dry center of gravity of
the damper.
DryCogZ- Type the offset distance along the z-axis for the dry center of gravity of
the damper.
WaterWeight- Type the water weight of the damper.
-
8/13/2019 Hvac Reference Data Guide
20/79
HVAC Sheets: An Overview
20 HVAC Reference Data Guide
WaterCogX- Type the offset distance along the x-axis for the wet center of gravity
of the damper.
WaterCogY- Type the offset distance along the y-axis for the wet center of gravity
of the damper.
WaterCogZ- Type the offset distance along the z-axis for the wet center of gravityof the damper.
Width- Type the width of the damper.
DamperLength- Type the length for the damper.
Thickness- Type the thickness for the damper.
FlangeWidth- Type the width of the flange for the damper.
Tip
For the remaining properties, (i)indicates an integer corresponding to anozzle number assigned to the cross section. This method avoids a lengthy
listing for all possibilities, like Nozzle(1):CrossSection,Nozzle(2):CrossSection, and Nozzle(3):CrossSectionfor three possible
nozzles. When you type the nozzle properties in the workbook, substitute
a number for ito assign the nozzle to the appropriate property.
Nozzle(i):CrossSection- Type the related CrossSection object for the port as listed
on the HvacSpecsheet.
Nozzle(i):EndPrep- Type the coded end preparation for Nozzle 1. The
AllCodeLists.xlsworkbook contains mappings between numbers and components.For example, the number 11in the Nozzle EndPrepcolumn on the ManualDamper
sheet corresponds to the flat-face flanged end, as specified in the AllCodeLists.xls
workbook.
Nozzle(i):Thickness- Type the thickness of the nozzle port. The number of actual
nozzles present on a cableway run can vary.
Nozzle(i):FlangeWidth- Type the flange width for the nozzle.
Nozzle(i):FlowDirection- Type the flow direction for the nozzle.
Nozzle(i):PortDepth- Type the depth of the port for the nozzle.
Nozzle(i):CptOffset- Type the offset value for the component.
-
8/13/2019 Hvac Reference Data Guide
21/79
HVAC Sheets: An Overview
HVAC Reference Data Guide 21
Related Topics
BellMouthRFO Sheet, page 65 BellMouthRound Sheet, page 64 DuctSmokeDetector Sheet, page 45 FlatOval_Rivet Sheet, page 43
FlatOval_Weld Sheet, page 42 Horn_Strobe Sheet, page 47 HsqrThroatElbow Sheet, page 62 HVAC Sheets: An Overview, page 13 HVACElbow Sheet, page 58 HVACSpec Sheet, page 15 HvacSpecDefaults Sheet, page 76 PermissibleDuctThickness Sheet, page 78 Rect_FlatFlange Sheet, page 24 Rect_FlatFlangeVA Sheet, page 28 Rect_Rivet Sheet, page 40
Rect_Sleeve Sheet, page 34 Rect_Weld Sheet, page 37 RectTee Sheet, page 56 Round_FlatFlange Sheet, page 26 Round_FlatFlangeVA Sheet, page 30 Round_Rivet Sheet, page 39 Round_Sleeve Sheet, page 32 Round_Weld Sheet, page 36 RoundElbow Sheet, page 60 RoundTee Sheet, page 54 SamplingTube Sheet, page 46 SMRectangularBranch Sheet, page 53 SMRoundBranch Sheet, page 52 SurfMountIcover Sheet, page 48
-
8/13/2019 Hvac Reference Data Guide
22/79
HVAC Sheets: An Overview
22 HVAC Reference Data Guide
MotorDamper Sheet
The MotorDampersheet in the HVAC.xlsworkbook defines the motorized dampers
that you want in the Catalog.
PartNumber- Type the part number assigned to the motorized damper. The softwareuses the part number at placement when the part name is automatically generated. Anexample is MRD-URD-100(MRDrepresents motorized damper. URDrepresents
non-motorized damper.)
Tip
Part numbers for Motor dampers must be unique throughout the entireCatalog.
SymbolDefinition- Type the definition of the Visual Basic symbol that you are
creating for the Motor damper. An example is
PDSMotorRoundDamper.CMotorRoundDamper.
FaceWidth- Type the width of the face for the damper.
FaceDepth- Type the face depth for the damper.
ComponentType- Type the component type for the damper.
PartDescription- Type a description for the damper. An example is Motorized
Round Damper 100mm diameter model URD Ultra-Zone.
Width- Type the width of the damper.
DamperLength- Type the length for the damper.
Thickness- Type the thickness for the damper.
FlangeWidth- Type the width of the flange for the damper.
Tip
For the remaining properties, (i)indicates an integer corresponding to anozzle number assigned to the cross section. This method avoids a lengthy
listing for all possibilities, like Nozzle(1):CrossSection,Nozzle(2):CrossSection, and Nozzle(3):CrossSectionfor three possible
nozzles. When you type the nozzle properties in the workbook, substitutea number for ito assign the nozzle to the appropriate property.
Nozzle(i):CrossSection- Type the related CrossSection object for the port as listed
on the HvacSpecsheet.
-
8/13/2019 Hvac Reference Data Guide
23/79
HVAC Sheets: An Overview
HVAC Reference Data Guide 23
Nozzle(i):EndPrep- Type the coded end preparation for Nozzle 1. The
AllCodeLists.xlsworkbook contains mappings between numbers and components.For example, the number 11in the Nozzle EndPrepcolumn on the MotorDamper
sheet corresponds to the flat-face flanged end, as specified in the AllCodeLists.xls
workbook.
Nozzle(i):Thickness- Type the thickness of the nozzle port. The number of actual
nozzles present on a cableway run can vary.
Nozzle(i):FlangeWidth- Type the flange width for the nozzle.
Nozzle(i):FlowDirection- Type the flow direction for the nozzle.
Nozzle(i):PortDepth- Type the depth of the port for the nozzle.
Nozzle(i):CptOffset- Type the offset value for the component.
Related Topics BellMouthRFO Sheet, page 65 BellMouthRound Sheet, page 64 DuctSmokeDetector Sheet, page 45 FlatOval_Rivet Sheet, page 43 FlatOval_Weld Sheet, page 42 Horn_Strobe Sheet, page 47 HsqrThroatElbow Sheet, page 62 HVAC Sheets: An Overview, page 13 HVACElbow Sheet, page 58 HVACSpec Sheet, page 15 HvacSpecDefaults Sheet, page 76 PermissibleDuctThickness Sheet, page 78 Rect_FlatFlange Sheet, page 24 Rect_FlatFlangeVA Sheet, page 28 Rect_Rivet Sheet, page 40 Rect_Sleeve Sheet, page 34 Rect_Weld Sheet, page 37 RectTee Sheet, page 56 Round_FlatFlange Sheet, page 26 Round_FlatFlangeVA Sheet, page 30 Round_Rivet Sheet, page 39 Round_Sleeve Sheet, page 32 Round_Weld Sheet, page 36 RoundElbow Sheet, page 60 RoundTee Sheet, page 54 SamplingTube Sheet, page 46 SMRectangularBranch Sheet, page 53 SMRoundBranch Sheet, page 52 SurfMountIcover Sheet, page 48
-
8/13/2019 Hvac Reference Data Guide
24/79
HVAC Sheets: An Overview
24 HVAC Reference Data Guide
Rect_FlatFlange Sheet
The Rect_FlatFlangesheet in the HVAC.xlsworkbook organizes facts for
rectangular flat flanges.
PartNumber- Type the part number for the flange. An example is RECTFFforrectangular flat flange.
Tip
Part numbers for rectangular flat flanges must be unique throughout theentire Catalog.
FaceDepth- Type the face depth for the coil.
FaceWidth- Type the face width for the coil.
ComponentType- Type the component type for the rectangular flat flange.
PartDescription- Type a description for the rectangular flat flange.
SymbolDefinition- Type the symbol definition for the rectangular flat flange.
Width- Type the width of the duct.
Depth- Type the depth of the duct.
Clearance- Type the clearance for the rectangular flat flange.
FlangeWidth- Type the width of the flange.
Thickness- Type the thickness for the flange.
CompressedGasket- Type the thickness for the compressed gasket.
Tip
For the remaining properties, (i)indicates an integer corresponding to anozzle number assigned to the cross section. This method avoids a lengthy
listing for all possibilities, like Nozzle(1):CrossSection,Nozzle(2):CrossSection, and Nozzle(3):CrossSectionfor three possible
nozzles. When you type the nozzle properties in the workbook, substitute
a number for ito assign the nozzle to the appropriate property.Nozzle(i):CrossSection-Type the related CrossSection object for the port.
Nozzle(i):EndPrep- Type the coded end preparation for the nozzle. Examples of end
preparations include Threaded, Screwed, Plain End, Welded, Bolted, Female,
Male, and Ferule. In the reference data, a number represents each type of end
preparation (for example, 1for Threaded, 2for Screwedand so on).
-
8/13/2019 Hvac Reference Data Guide
25/79
-
8/13/2019 Hvac Reference Data Guide
26/79
HVAC Sheets: An Overview
26 HVAC Reference Data Guide
Round_FlatFlange Sheet
The Round_FlatFlangesheet in the HVAC.xlsworkbook defines the round flat
flanges that you want in the Catalog.
PartNumber- Type the part number for the flange. An example is ROUNDFFforround flat flange.
Tip
Part numbers for round flat flanges must be unique throughout the entireCatalog.
SymbolDefinition- Type the symbol definition for the round flat flange. An example
is PDSRoundFlatFlange.HROUNDFF.
FaceDepth- Type the face depth for the coil.
FaceWidth- Type the face width for the coil.
ComponentType- Type the component type for the round flat flange.
PartDescription- Type a description for the round flat flange.
Width- Type the width of the duct.
Clearance- Type the clearance for the round flat flange.
FlangeWidth- Type the width of the flange.
Thickness- Type the thickness for the flange.
CompressedGasket- Type the thickness for the compressed gasket.
Tip
For the remaining properties, (i)indicates an integer corresponding to anozzle number assigned to the cross section. This method avoids a lengthylisting for all possibilities, like Nozzle(1):CrossSection,
Nozzle(2):CrossSection, and Nozzle(3):CrossSectionfor three possible
nozzles. When you type the nozzle properties in the workbook, substitutea number for ito assign the nozzle to the appropriate property.
Nozzle(i):CrossSection- Type the related CrossSection object for the port.
Nozzle(i):EndPrep- Type the coded end preparation for the nozzle. Examples of end
preparations include Threaded, Screwed, Plain End, Welded, Bolted, Female,
Male, and Ferule. In the reference data, a number represents each type of end
preparation (for example, 1for Threaded, 2for Screwedand so on).
Nozzle(i):Thickness- Type the thickness of for the particular nozzle port.
-
8/13/2019 Hvac Reference Data Guide
27/79
HVAC Sheets: An Overview
HVAC Reference Data Guide 27
Nozzle(i):FlangeWidth- Type the flange width for the nozzle.
Nozzle(i):FlowDirection- Type the flow direction for the nozzle.
Nozzle(i):PortDepth- Type the depth of the port for nozzle.
Nozzle(i):CptOffset- Type the offset value for the component.
Related Topics
BellMouthRFO Sheet, page 65 BellMouthRound Sheet, page 64 DuctSmokeDetector Sheet, page 45 FlatOval_Rivet Sheet, page 43 FlatOval_Weld Sheet, page 42 Horn_Strobe Sheet, page 47 HsqrThroatElbow Sheet, page 62 HVAC Sheets: An Overview, page 13 HVACElbow Sheet, page 58 HVACSpec Sheet, page 15 HvacSpecDefaults Sheet, page 76 ManualDamper Sheet, page 19 PermissibleDuctThickness Sheet, page 78 Rect_FlatFlange Sheet, page 24 Rect_FlatFlangeVA Sheet, page 28 Rect_Rivet Sheet, page 40 Rect_Sleeve Sheet, page 34 Rect_Weld Sheet, page 37 RectTee Sheet, page 56 Round_FlatFlangeVA Sheet, page 30 Round_Rivet Sheet, page 39 Round_Sleeve Sheet, page 32 Round_Weld Sheet, page 36 RoundElbow Sheet, page 60 RoundTee Sheet, page 54 SamplingTube Sheet, page 46 SMRectangularBranch Sheet, page 53 SMRoundBranch Sheet, page 52 SurfMountIcover Sheet, page 48
-
8/13/2019 Hvac Reference Data Guide
28/79
HVAC Sheets: An Overview
28 HVAC Reference Data Guide
Rect_FlatFlangeVA Sheet
The Rect_FlatFlangeVAsheet in the HVAC.xlsworkbook organizes facts for
rectangular sloped flanges.
PartNumber- Type the part number for the flange. An example isRect_SlopedFlangefor rectangular sloped flange.
Tip
Part numbers for rectangular flat flanges must be unique throughout theentire Catalog.
FaceDepth- Type the face depth for the coil.
FaceWidth- Type the face width for the coil.
ComponentType- Type the component type for the rectangular flat flange.
PartDescription- Type a description for the rectangular flat flange.
SymbolDefinition- Type the symbol definition for the rectangular flat flange.
Width- Type the width of the duct.
Depth- Type the depth of the duct.
Clearance- Type the clearance for the rectangular flat flange.
FlangeWidth- Type the width of the flange.
Thickness- Type the thickness for the flange.
CompressedGasket- Type the thickness for the compressed gasket.
Tip
For the remaining properties, (i)indicates an integer corresponding to anozzle number assigned to the cross section. This method avoids a lengthy
listing for all possibilities, like Nozzle(1):CrossSection,Nozzle(2):CrossSection, and Nozzle(3):CrossSectionfor three possible
nozzles. When you type the nozzle properties in the workbook, substitute
a number for ito assign the nozzle to the appropriate property.Nozzle(i):CrossSection-Type the related CrossSection object for the port.
Nozzle(i):EndPrep- Type the coded end preparation for the nozzle. Examples of end
preparations include Threaded, Screwed, Plain End, Welded, Bolted, Female,
Male, and Ferule. In the reference data, a number represents each type of end
preparation (for example, 1for Threaded, 2for Screwedand so on).
-
8/13/2019 Hvac Reference Data Guide
29/79
HVAC Sheets: An Overview
HVAC Reference Data Guide 29
Nozzle(i):Thickness- Type the thickness of the nozzle port.
Nozzle(i):FlangeWidth- Type the flange width for the nozzle.
Nozzle(i):FlowDirection- Type the flow direction for the nozzle.
Nozzle(i):PortDepth- Type the depth of the port for the nozzle.
Nozzle(i):CptOffset- Type the offset value for the component.
Related Topics
BellMouthRFO Sheet, page 65 BellMouthRound Sheet, page 64 DuctSmokeDetector Sheet, page 45 FlatOval_Rivet Sheet, page 43 FlatOval_Weld Sheet, page 42 Horn_Strobe Sheet, page 47 HsqrThroatElbow Sheet, page 62 HVAC Sheets: An Overview, page 13 HVACElbow Sheet, page 58 HVACSpec Sheet, page 15 HvacSpecDefaults Sheet, page 76 ManualDamper Sheet, page 19 PermissibleDuctThickness Sheet, page 78 Rect_Rivet Sheet, page 40 Rect_Sleeve Sheet, page 34 Rect_Weld Sheet, page 37 RectTee Sheet, page 56
Round_FlatFlange Sheet, page 26 Round_Rivet Sheet, page 39 Round_Sleeve Sheet, page 32 Round_Weld Sheet, page 36 RoundElbow Sheet, page 60 RoundTee Sheet, page 54 SamplingTube Sheet, page 46 SMRectangularBranch Sheet, page 53 SMRoundBranch Sheet, page 52 SurfMountIcover Sheet, page 48
-
8/13/2019 Hvac Reference Data Guide
30/79
HVAC Sheets: An Overview
30 HVAC Reference Data Guide
Round_FlatFlangeVA Sheet
The Round_FlatFlangeVAsheet in the HVAC.xlsworkbook organizes facts for
round flat flanges with depth inclination.
PartNumber- Type the part number for the flange. An example isRound_SlopedFlangefor round sloped flange.
Tip
Part numbers for rectangular flat flanges must be unique throughout theentire Catalog.
FaceDepth- Type the face depth for the coil.
FaceWidth- Type the face width for the coil.
ComponentType- Type the component type for the rectangular flat flange.
PartDescription- Type a description for the rectangular flat flange.
SymbolDefinition- Type the symbol definition for the rectangular flat flange.
Width- Type the width of the duct.
Clearance- Type the clearance for the rectangular flat flange.
FlangeWidth- Type the width of the flange.
Thickness- Type the thickness for the flange.
CompressedGasket- Type the thickness for the compressed gasket.
Tip
For the remaining properties, (i)indicates an integer corresponding to anozzle number assigned to the cross section. This method avoids a lengthy
listing for all possibilities, like Nozzle(1):CrossSection,Nozzle(2):CrossSection, and Nozzle(3):CrossSectionfor three possible
nozzles. When you type the nozzle properties in the workbook, substitute
a number for ito assign the nozzle to the appropriate property.
Nozzle(i):CrossSection-Type the related CrossSection object for the port.
Nozzle(i):EndPrep- Type the coded end preparation for the nozzle. Examples of endpreparations include Threaded, Screwed, Plain End, Welded, Bolted, Female,
Male, and Ferule. In the reference data, a number represents each type of end
preparation (for example, 1for Threaded, 2for Screwedand so on).
Nozzle(i):Thickness- Type the thickness of the nozzle port.
-
8/13/2019 Hvac Reference Data Guide
31/79
HVAC Sheets: An Overview
HVAC Reference Data Guide 31
Nozzle(i):FlangeWidth- Type the flange width for the nozzle.
Nozzle(i):FlowDirection- Type the flow direction for the nozzle.
Nozzle(i):PortDepth- Type the depth of the port for the nozzle.
Nozzle(i):CptOffset- Type the offset value for the component.
Related Topics
BellMouthRFO Sheet, page 65 BellMouthRound Sheet, page 64 DuctSmokeDetector Sheet, page 45 FlatOval_Rivet Sheet, page 43 FlatOval_Weld Sheet, page 42 Horn_Strobe Sheet, page 47 HsqrThroatElbow Sheet, page 62 HVAC Sheets: An Overview, page 13 HVACElbow Sheet, page 58 HVACSpec Sheet, page 15 HvacSpecDefaults Sheet, page 76 ManualDamper Sheet, page 19 PermissibleDuctThickness Sheet, page 78 Rect_Rivet Sheet, page 40 Rect_Sleeve Sheet, page 34 Rect_Weld Sheet, page 37 RectTee Sheet, page 56 Round_FlatFlange Sheet, page 26 Round_Rivet Sheet, page 39 Round_Sleeve Sheet, page 32 Round_Weld Sheet, page 36 RoundElbow Sheet, page 60 RoundTee Sheet, page 54 SamplingTube Sheet, page 46 SMRectangularBranch Sheet, page 53 SMRoundBranch Sheet, page 52 SurfMountIcover Sheet, page 48
-
8/13/2019 Hvac Reference Data Guide
32/79
HVAC Sheets: An Overview
32 HVAC Reference Data Guide
Round_Sleeve Sheet
The Round_Sleevesheet in the HVAC.xlsworkbook defines the round sleeves that
you want in the Catalog.
PartNumber- Type the part number for the sleeve. An example isROUNDSLEEVEfor round sleeve.
Tip
Part numbers for round sleeves must be unique throughout the entireCatalog.
FaceDepth- Type the face depth for the object.
FaceWidth- Type the face width for the object.
ComponentType- Type the component type for the round sleeve.
PartDescription- Type a description for the round sleeve.
SymbolDefinition- Type the symbol definition for the round sleeve. An example is
PDSHRoundSleeve.HROUNDSLV.
Width- Type the width of the duct.
Clearance- Type the clearance for the round sleeve.
Length- Type the length of the round sleeve.
Thickness- Type the thickness for the sleeve.
Tip
For the remaining properties, (i)indicates an integer corresponding to anozzle number assigned to the cross section. This method avoids a lengthy
listing for all possibilities, like Nozzle(1):CrossSection,Nozzle(2):CrossSection, and Nozzle(3):CrossSectionfor three possible
nozzles. When you type the nozzle properties in the workbook, substitute
a number for ito assign the nozzle to the appropriate property.
Nozzle(i):CrossSection- Type the related CrossSection object for the port.
Nozzle(i):EndPrep- Type the coded end preparation for the nozzle. Examples of end
preparations include Threaded, Screwed, Plain End, Welded, Bolted, Female,
Male, and Ferule. In the reference data, a number represents each type of end
preparation (for example, 1for Threaded, 2for Screwedand so on).
Nozzle(i):Thickness- Type the thickness of the nozzle port.
Nozzle(i):FlangeWidth- Type the sleeve width for the nozzle.
-
8/13/2019 Hvac Reference Data Guide
33/79
HVAC Sheets: An Overview
HVAC Reference Data Guide 33
Nozzle(i):FlowDirection- Type the flow direction for the nozzle.
Nozzle(i):PortDepth- Type the depth of the port for the nozzle.
Nozzle(i):CptOffset- Type the offset value for the component.
Related Topics BellMouthRound Sheet, page 64 HsqrThroatElbow Sheet, page 62 HVAC Sheets: An Overview, page 13 HVACElbow Sheet, page 58 HVACSpec Sheet, page 15 HvacSpecDefaults Sheet, page 76 ManualDamper Sheet, page 19 Rect_FlatFlange Sheet, page 24 Rect_FlatFlangeVA Sheet, page 28 Rect_Sleeve Sheet, page 34 RectTee Sheet, page 56 Round_FlatFlange Sheet, page 26 Round_FlatFlangeVA Sheet, page 30 RoundElbow Sheet, page 60 RoundTee Sheet, page 54 SMRectangularBranch Sheet, page 53 SMRoundBranch Sheet, page 52 SurfMountIcover Sheet, page 48
-
8/13/2019 Hvac Reference Data Guide
34/79
HVAC Sheets: An Overview
34 HVAC Reference Data Guide
Rect_Sleeve Sheet
The Rect_Sleevesheet in the HVAC.xlsworkbook organizes facts for rectangular
sleeves.
PartNumber- Type the part number for the sleeve. An example is RECTSLEEVEfor rectangular sleeve.
Tip
Part numbers for rectangular sleeves must be unique throughout the entireCatalog.
FaceDepth- Type the face depth for the object.
FaceWidth- Type the face width for the object.
ComponentType- Type the component type for the rectangular sleeve.
PartDescription- Type a description for the rectangular sleeve.
SymbolDefinition- Type the symbol definition for the rectangular sleeve. An
example is PBSHRectSleeve.HRECTV.
Width- Type the width of the duct.
Depth- Type the depth of the duct.
Clearance- Type the clearance for the rectangular sleeve.
Length- Type the length of the rectangular sleeve.
Thickness- Type the thickness for the sleeve.
Tip
For the remaining properties, (i)indicates an integer corresponding to anozzle number assigned to the cross section. This method avoids a lengthylisting for all possibilities, like Nozzle(1):CrossSection,
Nozzle(2):CrossSection, and Nozzle(3):CrossSectionfor three possible
nozzles. When you type the nozzle properties in the workbook, substitutea number for ito assign the nozzle to the appropriate property.
Nozzle(i):EndPrep- Type the coded end preparation for the particular nozzle.
Examples of end preparations include Threaded, Screwed, Plain End, Welded,
Bolted, Female, Male, and Ferule. In the reference data, a number represents each
type of end preparation (for example, 1for Threaded, 2for Screwedand so on).
Nozzle(i):Thickness- Type the thickness of the nozzle port.
Nozzle(i):CrossSection- Type the related CrossSection object for the port.
-
8/13/2019 Hvac Reference Data Guide
35/79
-
8/13/2019 Hvac Reference Data Guide
36/79
HVAC Sheets: An Overview
36 HVAC Reference Data Guide
Round_Weld Sheet
The Round_Sleevesheet in the HVAC.xlsworkbook defines the round welds that
you want in the Catalog.
PartNumber- Type the part number for the weld. An example is RoundWeldforround weld.
Tip
Part numbers for round sleeves must be unique throughout the entireCatalog.
FaceDepth- Type the face depth for the object.
FaceWidth- Type the face width for the object.
ComponentType- Type the component type for the round weld.
PartDescription- Type a description for the round weld.
SymbolDefinition- Type the symbol definition for the round weld. An example is
SP3DHVACRoundWeld.CHVACRoundWeld.
Width- Type the width of the duct.
Tip
For the remaining properties, (i)indicates an integer corresponding to anozzle number assigned to the cross section. This method avoids a lengthy
listing for all possibilities, like Nozzle(1):CrossSection,Nozzle(2):CrossSection, and Nozzle(3):CrossSectionfor three possible
nozzles. When you type the nozzle properties in the workbook, substitute
a number for ito assign the nozzle to the appropriate property.
Nozzle(i):CrossSection- Type the related CrossSection object for the port.
Nozzle(i):EndPrep- Type the coded end preparation for the nozzle. Examples of end
preparations include Threaded, Screwed, Plain End, Welded, Bolted, Female,Male, and Ferule. In the reference data, a number represents each type of end
preparation (for example, 1for Threaded, 2for Screwedand so on).
Nozzle(i):Thickness- Type the thickness of the nozzle port.
Nozzle(i):FlangeWidth- Type the sleeve width for the nozzle.
Nozzle(i):FlowDirection- Type the flow direction for the nozzle.
Nozzle(i):PortDepth- Type the depth of the port for the nozzle.
Nozzle(i):CptOffset- Type the offset value for the component.
-
8/13/2019 Hvac Reference Data Guide
37/79
HVAC Sheets: An Overview
HVAC Reference Data Guide 37
Related Topics
BellMouthRound Sheet, page 64 HsqrThroatElbow Sheet, page 62 HVAC Sheets: An Overview, page 13 HVACElbow Sheet, page 58
HVACSpec Sheet, page 15 HvacSpecDefaults Sheet, page 76 ManualDamper Sheet, page 19 Rect_FlatFlange Sheet, page 24 Rect_FlatFlangeVA Sheet, page 28 Rect_Sleeve Sheet, page 34 RectTee Sheet, page 56 Round_FlatFlange Sheet, page 26 Round_FlatFlangeVA Sheet, page 30 RoundElbow Sheet, page 60 RoundTee Sheet, page 54
SMRectangularBranch Sheet, page 53 SMRoundBranch Sheet, page 52 SurfMountIcover Sheet, page 48
Rect_Weld Sheet
The Rect_Sleevesheet in the HVAC.xlsworkbook defines the rectangular welds that
you want in the Catalog.
PartNumber- Type the part number for the weld. An example is RectWeldfor
rectangular weld.
Tip
Part numbers for round sleeves must be unique throughout the entireCatalog.
FaceDepth- Type the face depth for the object.
FaceWidth- Type the face width for the object.
ComponentType- Type the component type for the weld.
PartDescription- Type a description for the weld.
SymbolDefinition- Type the symbol definition for the weld. An example is
SP3DHVACRectWeld.CHVACRectWeld.
Width- Type the width of the duct.
Depth- Type the depth of the duct.
-
8/13/2019 Hvac Reference Data Guide
38/79
HVAC Sheets: An Overview
38 HVAC Reference Data Guide
Tip
For the remaining properties, (i)indicates an integer corresponding to anozzle number assigned to the cross section. This method avoids a lengthy
listing for all possibilities, like Nozzle(1):CrossSection,
Nozzle(2):CrossSection, and Nozzle(3):CrossSectionfor three possible
nozzles. When you type the nozzle properties in the workbook, substitutea number for ito assign the nozzle to the appropriate property.
Nozzle(i):CrossSection- Type the related CrossSection object for the port.
Nozzle(i):EndPrep- Type the coded end preparation for the nozzle. Examples of end
preparations include Threaded, Screwed, Plain End, Welded, Bolted, Female,Male, and Ferule. In the reference data, a number represents each type of end
preparation (for example, 1for Threaded, 2for Screwedand so on).
Nozzle(i):Thickness- Type the thickness of the nozzle port.
Nozzle(i):FlangeWidth- Type the sleeve width for the nozzle.
Nozzle(i):FlowDirection- Type the flow direction for the nozzle.
Nozzle(i):PortDepth- Type the depth of the port for the nozzle.
Nozzle(i):CptOffset- Type the offset value for the component.
Related Topics
BellMouthRound Sheet, page 64 HsqrThroatElbow Sheet, page 62 HVAC Sheets: An Overview, page 13 HVACElbow Sheet, page 58 HVACSpec Sheet, page 15 HvacSpecDefaults Sheet, page 76 ManualDamper Sheet, page 19 Rect_FlatFlange Sheet, page 24 Rect_FlatFlangeVA Sheet, page 28 Rect_Sleeve Sheet, page 34 RectTee Sheet, page 56 Round_FlatFlange Sheet, page 26 Round_FlatFlangeVA Sheet, page 30 RoundElbow Sheet, page 60 RoundTee Sheet, page 54 SMRectangularBranch Sheet, page 53 SMRoundBranch Sheet, page 52 SurfMountIcover Sheet, page 48
-
8/13/2019 Hvac Reference Data Guide
39/79
HVAC Sheets: An Overview
HVAC Reference Data Guide 39
Round_Rivet Sheet
The Round_Rivetsheet in the HVAC.xlsworkbook defines the round rivet
connections that you want in the Catalog.
PartNumber- Type the part number for the rivet connections. An example isRoundRivetfor round rivet.
Tip
Part numbers for round rivets must be unique throughout the entireCatalog.
FaceDepth- Type the face depth for the object.
FaceWidth- Type the face width for the object.
ComponentType- Type the component type for the round rivet.
PartDescription- Type a description for the round rivet.
SymbolDefinition- Type the symbol definition for the round rivet. An example is
SP3DHVACRoundRivet.CHVACRoundRivet.
Width- Type the width of the duct.
Tip
For the remaining properties, (i)indicates an integer corresponding to anozzle number assigned to the cross section. This method avoids a lengthy
listing for all possibilities, like Nozzle(1):CrossSection,Nozzle(2):CrossSection, and Nozzle(3):CrossSectionfor three possible
nozzles. When you type the nozzle properties in the workbook, substitute
a number for ito assign the nozzle to the appropriate property.
Nozzle(i):CrossSection- Type the related CrossSection object for the port.
Nozzle(i):EndPrep- Type the coded end preparation for the nozzle. Examples of end
preparations include Threaded, Screwed, Plain End, Welded, Bolted, Female,Male, and Ferule. In the reference data, a number represents each type of end
preparation (for example, 1for Threaded, 2for Screwedand so on).
Nozzle(i):Thickness- Type the thickness of the nozzle port.
Nozzle(i):FlangeWidth- Type the sleeve width for the nozzle.
Nozzle(i):FlowDirection- Type the flow direction for the nozzle.
Nozzle(i):PortDepth- Type the depth of the port for the nozzle.
-
8/13/2019 Hvac Reference Data Guide
40/79
HVAC Sheets: An Overview
40 HVAC Reference Data Guide
Nozzle(i):CptOffset- Type the offset value for the component.
Related Topics
BellMouthRound Sheet, page 64 HsqrThroatElbow Sheet, page 62
HVAC Sheets: An Overview, page 13 HVACElbow Sheet, page 58 HVACSpec Sheet, page 15 HvacSpecDefaults Sheet, page 76 ManualDamper Sheet, page 19 Rect_FlatFlange Sheet, page 24 Rect_FlatFlangeVA Sheet, page 28 Rect_Sleeve Sheet, page 34 RectTee Sheet, page 56 Round_FlatFlange Sheet, page 26 Round_FlatFlangeVA Sheet, page 30
RoundElbow Sheet, page 60 RoundTee Sheet, page 54 SMRectangularBranch Sheet, page 53 SMRoundBranch Sheet, page 52 SurfMountIcover Sheet, page 48
Rect_Rivet Sheet
The Rect_Rivetsheet in the HVAC.xlsworkbook defines the rectangular rivets that
you want in the Catalog.
PartNumber- Type the part number for the rivet. An example is RectRivetforrectangular rivet.
Tip
Part numbers for rectangular rivets must be unique throughout the entireCatalog.
FaceDepth- Type the face depth for the object.
FaceWidth- Type the face width for the object.
ComponentType- Type the component type for the rivet.
PartDescription- Type a description for the rivet.
SymbolDefinition- Type the symbol definition for the rivet. An example is
SP3DHVACRectRivet.CHVACRectRivet.
Width- Type the width of the duct.
-
8/13/2019 Hvac Reference Data Guide
41/79
HVAC Sheets: An Overview
HVAC Reference Data Guide 41
Depth- Type the depth of the duct.
Tip
For the remaining properties, (i)indicates an integer corresponding to anozzle number assigned to the cross section. This method avoids a lengthy
listing for all possibilities, like Nozzle(1):CrossSection,Nozzle(2):CrossSection, and Nozzle(3):CrossSectionfor three possiblenozzles. When you type the nozzle properties in the workbook, substitute
a number for ito assign the nozzle to the appropriate property.
Nozzle(i):CrossSection- Type the related CrossSection object for the port.
Nozzle(i):EndPrep- Type the coded end preparation for the nozzle. Examples of end
preparations include Threaded, Screwed, Plain End, Welded, Bolted, Female,Male, and Ferule. In the reference data, a number represents each type of end
preparation (for example, 1for Threaded, 2for Screwedand so on).
Nozzle(i):Thickness- Type the thickness of the nozzle port.
Nozzle(i):FlangeWidth- Type the sleeve width for the nozzle.
Nozzle(i):FlowDirection- Type the flow direction for the nozzle.
Nozzle(i):PortDepth- Type the depth of the port for the nozzle.
Nozzle(i):CptOffset- Type the offset value for the component.
Related Topics
BellMouthRound Sheet, page 64 HsqrThroatElbow Sheet, page 62 HVAC Sheets: An Overview, page 13 HVACElbow Sheet, page 58 HVACSpec Sheet, page 15 HvacSpecDefaults Sheet, page 76 ManualDamper Sheet, page 19 Rect_FlatFlange Sheet, page 24 Rect_FlatFlangeVA Sheet, page 28 Rect_Sleeve Sheet, page 34 RectTee Sheet, page 56 Round_FlatFlange Sheet, page 26 Round_FlatFlangeVA Sheet, page 30 RoundElbow Sheet, page 60 RoundTee Sheet, page 54 SMRectangularBranch Sheet, page 53 SMRoundBranch Sheet, page 52 SurfMountIcover Sheet, page 48
-
8/13/2019 Hvac Reference Data Guide
42/79
HVAC Sheets: An Overview
42 HVAC Reference Data Guide
FlatOval_Weld Sheet
The FlatOval_Sleevesheet in the HVAC.xlsworkbook defines the flat oval welds
that you want in the Catalog.
PartNumber- Type the part number for the weld. An example is FlatOvalWeldforflat oval weld.
Tip
Part numbers for flat oval welds must be unique throughout the entireCatalog.
FaceDepth- Type the face depth for the object.
FaceWidth- Type the face width for the object.
ComponentType- Type the component type for the weld.
PartDescription- Type a description for the weld.
SymbolDefinition- Type the symbol definition for the weld. An example is
SP3DHVACFlatOvalWeld.CFlatOvWeld.
Width- Type the width of the duct.
Depth- Type the depth of the duct.
Tip
For the remaining properties, (i)indicates an integer corresponding to anozzle number assigned to the cross section. This method avoids a lengthy
listing for all possibilities, like Nozzle(1):CrossSection,
Nozzle(2):CrossSection, and Nozzle(3):CrossSectionfor three possiblenozzles. When you type the nozzle properties in the workbook, substitute
a number for ito assign the nozzle to the appropriate property.
Nozzle(i):CrossSection- Type the related CrossSection object for the port.
Nozzle(i):EndPrep- Type the coded end preparation for the nozzle. Examples of end
preparations include Threaded, Screwed, Plain End, Welded, Bolted, Female,
Male, and Ferule. In the reference data, a number represents each type of end
preparation (for example, 1for Threaded, 2for Screwedand so on).
Nozzle(i):Thickness- Type the thickness of the nozzle port.
Nozzle(i):FlangeWidth- Type the sleeve width for the nozzle.
Nozzle(i):FlowDirection- Type the flow direction for the nozzle.
Nozzle(i):PortDepth- Type the depth of the port for the nozzle.
-
8/13/2019 Hvac Reference Data Guide
43/79
-
8/13/2019 Hvac Reference Data Guide
44/79
HVAC Sheets: An Overview
44 HVAC Reference Data Guide
Depth- Type the depth of the duct.
Tip
For the remaining properties, (i)indicates an integer corresponding to anozzle number assigned to the cross section. This method avoids a lengthy
listing for all possibilities, like Nozzle(1):CrossSection,Nozzle(2):CrossSection, and Nozzle(3):CrossSectionfor three possiblenozzles. When you type the nozzle properties in the workbook, substitute
a number for ito assign the nozzle to the appropriate property.
Nozzle(i):CrossSection- Type the related CrossSection object for the port.
Nozzle(i):EndPrep- Type the coded end preparation for the nozzle. Examples of end
preparations include Threaded, Screwed, Plain End, Welded, Bolted, Female,Male, and Ferule. In the reference data, a number represents each type of end
preparation (for example, 1for Threaded, 2for Screwedand so on).
Nozzle(i):Thickness- Type the thickness of the nozzle port.
Nozzle(i):FlangeWidth- Type the sleeve width for the nozzle.
Nozzle(i):FlowDirection- Type the flow direction for the nozzle.
Nozzle(i):PortDepth- Type the depth of the port for the nozzle.
Nozzle(i):CptOffset- Type the offset value for the component.
Related Topics
BellMouthRound Sheet, page 64 HsqrThroatElbow Sheet, page 62 HVAC Sheets: An Overview, page 13 HVACElbow Sheet, page 58 HVACSpec Sheet, page 15 HvacSpecDefaults Sheet, page 76 ManualDamper Sheet, page 19 Rect_FlatFlange Sheet, page 24 Rect_FlatFlangeVA Sheet, page 28 Rect_Sleeve Sheet, page 34 RectTee Sheet, page 56 Round_FlatFlange Sheet, page 26 Round_FlatFlangeVA Sheet, page 30 RoundElbow Sheet, page 60 RoundTee Sheet, page 54 SMRectangularBranch Sheet, page 53 SMRoundBranch Sheet, page 52 SurfMountIcover Sheet, page 48
-
8/13/2019 Hvac Reference Data Guide
45/79
HVAC Sheets: An Overview
HVAC Reference Data Guide 45
DuctSmokeDetector Sheet
The DuctSmokeDetectorsheet in the HVAC.xlsworkbook defines the duct smoke
detectors that you want in the Catalog.
PartNumber- Type the part number for the object. An example is SL-2000-Pfor anSL-2000 Photoelectric detector.
Tip
Part numbers must be unique throughout the entire Catalog.FaceDepth- Type the face depth for the object.
FaceWidth- Type the face width for the object.
ComponentType- Type the component type for the object.
PartDescription- Type a description for the object.
SymbolDefinition- Type the symbol definition for the object. An example is
GSCADHVACSurfMount.Cover.
CrossSectionShape- Type the cross section shape for the object.
Thickness- Type the thickness for the object.
Cover- Type the cover dimension for the object.
Holelength- Type the hole length dimension for the object.
Holebreadth- Type the hole breadth dimension for the object.
Covercornerradius- Type the cover corner radius for the object.
Gripdistance- Type the grip distance dimension for the object.
Handlelength- Type the handle length dimension for the object.
Related Topics
BellMouthRound Sheet, page 64 HsqrThroatElbow Sheet, page 62 HVAC Sheets: An Overview, page 13 HVACElbow Sheet, page 58 HVACSpec Sheet, page 15 HvacSpecDefaults Sheet, page 76 ManualDamper Sheet, page 19 Rect_FlatFlange Sheet, page 24 Rect_FlatFlangeVA Sheet, page 28 Rect_Sleeve Sheet, page 34
-
8/13/2019 Hvac Reference Data Guide
46/79
HVAC Sheets: An Overview
46 HVAC Reference Data Guide
RectTee Sheet, page 56 Round_FlatFlange Sheet, page 26 Round_FlatFlangeVA Sheet, page 30 RoundElbow Sheet, page 60 RoundTee Sheet, page 54
SMRectangularBranch Sheet, page 53 SMRoundBranch Sheet, page 52 SurfMountIcover Sheet, page 48
SamplingTube Sheet
The SamplingTubesheet in the HVAC.xlsworkbook defines the sampling tubes that
you want in the Catalog.
PartNumber- Type the part number for the object. An example is STS-100for an
STS-10 foot long sampling tube.
Tip
Part numbers must be unique throughout the entire Catalog.PartDescription- Type a description for the object.
Related Topics
BellMouthRound Sheet, page 64 HsqrThroatElbow Sheet, page 62 HVAC Sheets: An Overview, page 13 HVACElbow Sheet, page 58 HVACSpec Sheet, page 15 HvacSpecDefaults Sheet, page 76 ManualDamper Sheet, page 19 Rect_FlatFlange Sheet, page 24 Rect_FlatFlangeVA Sheet, page 28 Rect_Sleeve Sheet, page 34 RectTee Sheet, page 56 Round_FlatFlange Sheet, page 26 Round_FlatFlangeVA Sheet, page 30 RoundElbow Sheet, page 60 RoundTee Sheet, page 54
SMRectangularBranch Sheet, page 53 SMRoundBranch Sheet, page 52 SurfMountIcover Sheet, page 48
-
8/13/2019 Hvac Reference Data Guide
47/79
HVAC Sheets: An Overview
HVAC Reference Data Guide 47
Horn_Strobe Sheet
The Horn_Strobesheet in the HVAC.xlsworkbook defines the horn/strobe warning
signals that you want in the Catalog.
PartNumber- Type the part number for the object. An example is SHP24-1575Wfor a white 24VDC horn/strobe smoke visual and audible warning signal.
Tip
Part numbers must be unique throughout the entire Catalog.PartDescription- Type a description for the object.
Related Topics
BellMouthRound Sheet, page 64 HsqrThroatElbow Sheet, page 62 HVAC Sheets: An Overview, page 13 HVACElbow Sheet, page 58 HVACSpec Sheet, page 15 HvacSpecDefaults Sheet, page 76 ManualDamper Sheet, page 19 Rect_FlatFlange Sheet, page 24 Rect_FlatFlangeVA Sheet, page 28 Rect_Sleeve Sheet, page 34 RectTee Sheet, page 56 Round_FlatFlange Sheet, page 26 Round_FlatFlangeVA Sheet, page 30 RoundElbow Sheet, page 60 RoundTee Sheet, page 54 SMRectangularBranch Sheet, page 53 SMRoundBranch Sheet, page 52 SurfMountIcover Sheet, page 48
-
8/13/2019 Hvac Reference Data Guide
48/79
HVAC Sheets: An Overview
48 HVAC Reference Data Guide
SurfMountIcover Sheet
The SurfMountIcoversheet in the HVAC.xlsworkbook defines the surface-
mounted inspection covers that you want in the Catalog.
PartNumber- Type the part number for the surface-mounted inspection cover. Anexample is Icover400x600.
Tip
Part numbers for surface-mounted inspection covers must be uniquethroughout the entire Catalog.
FaceDepth- Type the face depth for the cover.
FaceWidth- Type the face width for the cover.
ComponentType- Type the component type for the surface-mounted component.
PartDescription- Type a description for the surface-mounted cover. An example is
Inspection cover.
SymbolDefinition- Type the symbol definition for the surface-mounted component.
An example is PBSHVACSurfMount.Cover.
CrossSectionShape- Type the designation for the shape of the cross section.
Examples of possible shapes are Rectangular, Round, Flat Oval, and U-Shape.
Thickness- Type the correct measurement value for thickness of the surface-
mounted component.
cover- Type the correct measurement value for the cover.
holelength- Type the correct measurement value for holes in the cover.
holebreadth- Type the correct measurement value for breadth of holes in the cover.
covercornerradius- Type the name of the cross section associated with the surface-
mounted cover.
gripdistance- Type the value for the grip distance for the surface-mounted cover.
-
8/13/2019 Hvac Reference Data Guide
49/79
-
8/13/2019 Hvac Reference Data Guide
50/79
HVAC Sheets: An Overview
50 HVAC Reference Data Guide
SM1PipingTap Sheet
The SM1PipingTapsheet in the HVAC.xlsworkbook defines the reference data for
one surface-mounted piping tap on an HVAC duct for instrument assembly.
PartNumber- Type the part number for the surface-mounted piping tap. Examplesinclude:
SM1PTapSWhalfin- A surface-mounted piping tap that is socket-welded(represented by SW) and has .5" (represented by halfin) nominal piping
diameter
SM1PTapFThalfin- A surface-mounted piping tap that is female-threaded (represented by FT) and has .5" (represented by halfin) nominal
piping diameter
Tip
Part numbers for surface-mounted piping taps must be unique throughoutthe entire Catalog.
ComponentType- Type the component type for the piping tap.
PartDescription- Type a description for the piping tap. An example is Rect_Sleeve.
SymbolDefinition- Type the symbol definition for the piping tap. An example is
PBSHRectSleeve.HRECTSLV.
Tip
For the remaining properties, (i)indicates an integer corresponding to anozzle number assigned to the piping tap. This method avoids a lengthylisting for all possibilities, like Nozzle(1):CrossSection,
Nozzle(2):CrossSection, and Nozzle(3):CrossSectionfor three possiblenozzles. When you type the nozzle properties in the workbook, substitute
a number for ito assign the nozzle to the appropriate property.
Nozzle(i):Npd- Type the nominal piping diameter for the nozzle port.
Nozzle(i):NpdUnitType- Type the unit type for the nozzle port.
Nozzle(i):EndPrep- Type the coded end preparation for the nozzle. Examples of end
preparations include Threaded, Screwed, Plain End, Welded, Bolted, Female,
Male, and Ferule. In the reference data, a number represents each type of endpreparation (for example, 1for Threaded, 2for Screwedand so on).
Nozzle(i):EndStandard- Type the coded end standard for the nozzle.
Nozzle(i):ScheduleThickness- Type the schedule thickness for the nozzle.
Nozzle(i):PressureRating- Type the pressure rating for the nozzle.
-
8/13/2019 Hvac Reference Data Guide
51/79
HVAC Sheets: An Overview
HVAC Reference Data Guide 51
Nozzle(i)FlowDirection- Type the flow direction for the nozzle.
Nozzle(i)PipingPointBasis- Type the piping point basis for the nozzle.
Related Topics
BellMouthRFO Sheet, page 65 BellMouthRound Sheet, page 64 DuctSmokeDetector Sheet, page 45 FlatOval_Rivet Sheet, page 43 FlatOval_Weld Sheet, page 42 Horn_Strobe Sheet, page 47 HsqrThroatElbow Sheet, page 62 HVAC Sheets: An Overview, page 13 HVACElbow Sheet, page 58 HVACSpec Sheet, page 15 HvacSpecDefaults Sheet, page 76 ManualDamper Sheet, page 19 PermissibleDuctThickness Sheet, page 78 Rect_FlatFlange Sheet, page 24 Rect_FlatFlangeVA Sheet, page 28 Rect_Rivet Sheet, page 40 Rect_Sleeve Sheet, page 34 Rect_Weld Sheet, page 37 RectTee Sheet, page 56 Round_FlatFlange Sheet, page 26 Round_FlatFlangeVA Sheet, page 30 Round_Rivet Sheet, page 39 Round_Sleeve Sheet, page 32 Round_Weld Sheet, page 36 RoundElbow Sheet, page 60 RoundTee Sheet, page 54 SamplingTube Sheet, page 46 SMRectangularBranch Sheet, page 53 SMRoundBranch Sheet, page 52
-
8/13/2019 Hvac Reference Data Guide
52/79
HVAC Sheets: An Overview
52 HVAC Reference Data Guide
SMRoundBranch Sheet
The SMRoundBranchsheet in the HVAC.xlsworkbook defines the surface
mounted components with round nozzles that you want in the Catalog.
PartNumber- Type the part number for the round branch. An example isSMRoundBranch1.
PartDescription- Type a description for the object.
FaceWidth- Type the face width of the damper for the object.
FaceDepth- Type the face depth of the damper for the object.
ComponentType- Type the component type for the round tee.
SymbolDefinition- Type the symbol definition for the round tee. An example is
SP3DHvacSMRoundB.CHvacSMRoundB.
Related Topics
BellMouthRFO Sheet, page 65 BellMouthRound Sheet, page 64 DuctSmokeDetector Sheet, page 45 FlatOval_Rivet Sheet, page 43 FlatOval_Weld Sheet, page 42 Horn_Strobe Sheet, page 47 HsqrThroatElbow Sheet, page 62 HVAC Sheets: An Overview, page 13
HVACElbow Sheet, page 58 HVACSpec Sheet, page 15 HvacSpecDefaults Sheet, page 76 ManualDamper Sheet, page 19 PermissibleDuctThickness Sheet, page 78 Rect_FlatFlange Sheet, page 24 Rect_FlatFlangeVA Sheet, page 28 Rect_Rivet Sheet, page 40 Rect_Sleeve Sheet, page 34 Rect_Weld Sheet, page 37 Round_FlatFlange Sheet, page 26
Round_FlatFlangeVA Sheet, page 30 Round_Rivet Sheet, page 39 Round_Sleeve Sheet, page 32 Round_Weld Sheet, page 36 RoundElbow Sheet, page 60 SamplingTube Sheet, page 46 SurfMountIcover Sheet, page 48
-
8/13/2019 Hvac Reference Data Guide
53/79
HVAC Sheets: An Overview
HVAC Reference Data Guide 53
SMRectangularBranch Sheet
The SMRectangularBranchsheet in the HVAC.xlsworkbook defines the surface
mounted components with rectangular nozzles that you want in the Catalog.
PartNumber- Type the part number for the round branch. An example isSMRectangularBranch1.
PartDescription- Type a description for the object.
FaceWidth- Type the face width of the damper for the object.
FaceDepth- Type the face depth of the damper for the object.
ComponentType- Type the component type for the object.
SymbolDefinition- Type the symbol definition for the round tee. An example is
SP3DHvacSMRB.CHvacSMRB.
Related Topics
BellMouthRFO Sheet, page 65 BellMouthRound Sheet, page 64 DuctSmokeDetector Sheet, page 45 FlatOval_Rivet Sheet, page 43 FlatOval_Weld Sheet, page 42 Horn_Strobe Sheet, page 47 HsqrThroatElbow Sheet, page 62 HVAC Sheets: An Overview, page 13
HVACElbow Sheet, page 58 HVACSpec Sheet, page 15 HvacSpecDefaults Sheet, page 76 ManualDamper Sheet, page 19 PermissibleDuctThickness Sheet, page 78 Rect_FlatFlange Sheet, page 24 Rect_FlatFlangeVA Sheet, page 28 Rect_Rivet Sheet, page 40 Rect_Sleeve Sheet, page 34 Rect_Weld Sheet, page 37 Round_FlatFlange Sheet, page 26
Round_FlatFlangeVA Sheet, page 30 Round_Rivet Sheet, page 39 Round_Sleeve Sheet, page 32 Round_Weld Sheet, page 36 RoundElbow Sheet, page 60 SamplingTube Sheet, page 46 SurfMountIcover Sheet, page 48
-
8/13/2019 Hvac Reference Data Guide
54/79
HVAC Sheets: An Overview
54 HVAC Reference Data Guide
RoundTee Sheet
The RoundTeesheet in the HVAC.xlsworkbook defines the round tees that you
want in the Catalog.
PartNumber- Type the part number for the round tee. An example is TA-100X80.
PartDescription- Type a description for the round tee.
FaceWidth- Type the face width of the damper for the round tee.
FaceDepth- Type the face depth of the damper for the round tee.
ComponentType- Type the component type for the round tee.
SymbolDefinition- Type the symbol definition for the round tee. An example is
PBSHRoundRTE.HRoundRTE.
Width- Type the width of the duct.
BWidth- Type the width of the bend.
HLength- Type the length for the round tee.
BLength- Type the length of the bend.
Tip
For the remaining properties, (i)indicates an integer corresponding to anozzle number assigned to the cross section. This method avoids a lengthy
listing for all possibilities, like Nozzle(1):CrossSection,Nozzle(2):CrossSection, and Nozzle(3):CrossSectionfor three possible
nozzles. When you type the nozzle properties in the workbook, substitute
a number for ito assign the nozzle to the appropriate property.
Nozzle(i):CrossSection- Type the related CrossSection object for the port in the
particular nozzle.
Nozzle(i):EndPrep- Type the coded end preparation for the nozzle. Examples of end
preparations include Threaded, Screwed, Plain End, Welded, Bolted, Female,Male, and Ferule. In the reference data, a number represents each type of end
preparation (for example, 1for Threaded, 2for Screwedand so on).
Nozzle(i):Thickness- Type the thickness of the nozzle.
Nozzle(i):FlangeWidth- Type the flange width for the nozzle.
Nozzle(i):FlowDirection- Type the flow direction for the nozzle.
Nozzle(i):PortDepth- Type the depth of the port for the nozzle.
-
8/13/2019 Hvac Reference Data Guide
55/79
-
8/13/2019 Hvac Reference Data Guide
56/79
HVAC Sheets: An Overview
56 HVAC Reference Data Guide
RectTee Sheet
The RectTeesheet in the HVAC.xlsworkbook defines the rectangular tees that you
want in the Catalog.
PartNumber- Type the part number for the round tee. An example is RectTee1.
PartDescription- Type a description for the object.
FaceWidth- Type the face width of the damper for the object.
FaceDepth- Type the face depth of the damper for the object.
ComponentType- Type the component type for the object.
SymbolDefinition- Type the symbol definition for the object. An example is
SP3DHRectRTE.HRectRTE.
Width- Type the width of the duct.
Depth- Type the depth of the duct
BWidth- Type the width of the bend.
BDepth- Type the depth of the bend.
HLength- Type the length for the round tee.
BLength- Type the length of the bend.
PlaneOfBranch- Type the angle of the bend.
Tip
For the remaining properties, (i)indicates an integer corresponding to anozzle number assigned to the cross section. This method avoids a lengthy
listing for all possibilities, like Nozzle(1):CrossSection,Nozzle(2):CrossSection, and Nozzle(3):CrossSectionfor three possible
nozzles. When you type the nozzle properties in the workbook, substitute
a number for ito assign the nozzle to the appropriate property.
Nozzle(i):CrossSection- Type the related CrossSection object for the port in the
particular nozzle.
Nozzle(i):EndPrep- Type the coded end preparation for the nozzle. Examples of end
preparations include Threaded, Screwed, Plain End, Welded, Bolted, Female,Male, and Ferule. In the reference data, a number represents each type of end
preparation (for example, 1for Threaded, 2for Screwedand so on).
Nozzle(i):Thickness- Type the thickness of the nozzle.
-
8/13/2019 Hvac Reference Data Guide
57/79
HVAC Sheets: An Overview
HVAC Reference Data Guide 57
Nozzle(i):FlangeWidth- Type the flange width for the nozzle.
Nozzle(i):FlowDirection- Type the flow direction for the nozzle.
Nozzle(i):PortDepth- Type the depth of the port for the nozzle.
Nozzle(i):CptOffset- Type the offset value for the component.
Related Topics
BellMouthRFO Sheet, page 65 BellMouthRound Sheet, page 64 DuctSmokeDetector Sheet, page 45 FlatOval_Rivet Sheet, page 43 FlatOval_Weld Sheet, page 42 Horn_Strobe Sheet, page 47 HsqrThroatElbow Sheet, page 62 HVAC Sheets: An Overview, page 13 HVACElbow Sheet, page 58 HVACSpec Sheet, page 15 HvacSpecDefaults Sheet, page 76 ManualDamper Sheet, page 19 PermissibleDuctThickness Sheet, page 78 Rect_FlatFlange Sheet, page 24 Rect_FlatFlangeVA Sheet, page 28 Rect_Rivet Sheet, page 40 Rect_Sleeve Sheet, page 34 Rect_Weld Sheet, page 37 Round_FlatFlange Sheet, page 26 Round_FlatFlangeVA Sheet, page 30 Round_Rivet Sheet, page 39 Round_Sleeve Sheet, page 32 Round_Weld Sheet, page 36 RoundElbow Sheet, page 60 SamplingTube Sheet, page 46 SurfMountIcover Sheet, page 48
-
8/13/2019 Hvac Reference Data Guide
58/79
HVAC Sheets: An Overview
58 HVAC Reference Data Guide
HVACElbow Sheet
The HVACElbowsheet in the HVAC.xlsworkbook defines the elbows that you
want in the Catalog.
PartNumber- Type the part number for the elbow. An example is HVACElbowFo.
PartDescription- Type a description for the elbow. An example is variable shape
and angle elbow.
SymbolDefinition- Type the symbol definition for the elbow.
ComponentType- Type the component type for the elbow.
DryWeight- Type the empty weight of the elbow. You must specify the type of units
when you enter this value.
WaterWeight- Type the water weight of the elbow. You must specify the type ofunits when you enter this value.
DryCogX- Type the center-of-gravity location for the elbow along the X-axis when
the elbow is empty