hvac reference data guide

8/13/2019 Hvac Reference Data Guide

1/79

HVAC

Reference Data Guide

Versi on 2007 (7.0) January 2007 DSP3D-PE-200018G


2/79

CopyrightCopyright 2002-2007, Intergraph Corporation. All Rights Reserved.

Including software, file formats, and audiovisual displays; may be used pursuant to applicable software license

agreement; contains confidential and proprietary information of Intergraph and/or third parties which is protected by

copyright law, trade secret law, and international treaty, and may not be provided or otherwise made available

without proper authorization.

Portions of this software are owned by Spatial Corp. 1986-2007. All Rights Reserved.

Restricted Rights Legend

Use, duplication, or disclosure by the government is subject to restrictions as set forth below. For civilian agencies:

This was developed at private expense and is restricted computer software submitted with restricted rights inaccordance with subparagraphs (a) through (d) of the Commercial Computer Software - Restricted Rights clause at

52.227-19 of the Federal Acquisition Regulations (FAR) and its successors, and is unpublished and all rights are

reserved under the copyright laws of the United States. For units of the Department of Defense (DoD): This iscommercial computer software as defined at DFARS 252.227-7014 and the rights of the Government are as

specified at DFARS 227.7202-3.

Unpublished rights reserved under the copyright laws of the United States.

Intergraph Corporation

Huntsville, Alabama 35894-0001

Warranties and Liabilities

All warranties given by Intergraph Corporation about equipment or software are set forth in your purchase contract,

and nothing stated in, or implied by, this document or its contents shall be considered or deemed a modification or

amendment of such warranties. Intergraph believes the information in this publication is accurate as of its

publication date.

The information and the software discussed in this document are subject to change without notice and are subject toapplicable technical product descriptions. Intergraph Corporation is not responsible for any error that may appear in

this document.

The software discussed in this document is furnished under a license and may be used or copied only in accordance

with the terms of this license.No responsibility is assumed by Intergraph for the use or reliability of software on equipment that is not supplied by

Intergraph or its affiliated companies. THE USER OF THE SOFTWARE IS EXPECTED TO MAKE THE FINALEVALUATION AS TO THE USEFULNESS OF THE SOFTWARE IN HIS OWN ENVIRONMENT.

Intergraph is not responsible for the accuracy of delivered data including, but not limited to, catalog, reference and

symbol data. Users should verify for themselves that the data is accurate and suitable for their project work.

Trademarks

Intergraph, the Intergraph logo, SmartSketch, FrameWorks, SmartPlant, IntelliShip, INtools, ISOGEN, PDS, and

MARIAN are registered trademarks of Intergraph Corporation. Microsoft and Windows are registered trademarks of

Microsoft Corporation. ACIS is a registered trademark of SPATIAL TECHNOLOGY, INC. Infragistics,Presentation Layer Framework, ActiveTreeView Ctrl, ProtoViewCtl, ActiveThreed Ctrl, ActiveListBar Ctrl,

ActiveSplitter, ActiveToolbars Ctrl, ActiveToolbars Plus Ctrl, and ProtoView are trademarks of Infragistics, Inc.Portions of 2D DCM, 3D DCM, and HLM from D-Cubed Limited are incorporated. All rights reserved. Oracle, JD

Edwards, PeopleSoft, and Retek are registered trademarks of Oracle Corporation and/or its affiliates. Other brands

and product names are trademarks of their respective owners.


3/79

Table of Contents

HVAC Reference Data Guide 3

Table of Contents

Preface.................................................................................................................................5

SmartPlant 3D Documentation Set...............................................................................6Administrative Guides ........................................................................................................ 6User's Guides ...................................................................................................................... 7Reference Data Guides ....................................................................................................... 8ISOGEN Guides ................................................................................................................. 9

Documentation Comments .........................................................................................10

What's New in HVAC Reference Data.......................................................................11

HVAC Reference Data: An Overview............................................................................12

HVAC Sheets: An Overview...........................................................................................13

HVACSpec Sheet ............................................................................................................. 15ManualDamper Sheet........................................................................................................ 19MotorDamper Sheet.......................................................................................................... 22Rect_FlatFlange Sheet ...................................................................................................... 24Round_FlatFlange Sheet................................................................................................... 26Rect_FlatFlangeVA Sheet ................................................................................................ 28Round_FlatFlangeVA Sheet ............................................................................................. 30Round_Sleeve Sheet ......................................................................................................... 32Rect_Sleeve Sheet............................................................................................................. 34Round_Weld Sheet ........................................................................................................... 36Rect_Weld Sheet............................................................................................................... 37Round_Rivet Sheet ........................................................................................................... 39

Rect_Rivet Sheet............................................................................................................... 40FlatOval_Weld Sheet ........................................................................................................ 42FlatOval_Rivet Sheet ........................................................................................................ 43DuctSmokeDetector Sheet ................................................................................................ 45SamplingTube Sheet ......................................................................................................... 46Horn_Strobe Sheet ............................................................................................................ 47SurfMountIcover Sheet..................................................................................................... 48SM1PipingTap Sheet ........................................................................................................ 50SMRoundBranch Sheet..................................................................................................... 52SMRectangularBranch Sheet ............................................................................................ 53RoundTee Sheet ................................................................................................................ 54RectTee Sheet ...................................................................................................................56

HVACElbow Sheet........................................................................................................... 58RoundElbow Sheet............................................................................................................ 60HsqrThroatElbow Sheet.................................................................................................... 62BellMouthRound Sheet..................................................................................................... 64BellMouthRFO Sheet ....................................................................................................... 65Division2 Sheet................................................................................................................. 66DivisionW3 Sheet ............................................................................................................. 68AirFilter Sheet................................................................................................................... 70AirFilterHumidifier Sheet................................................................................................. 72


4/79

Table of Contents

4 HVAC Reference Data Guide

AirCoolingCoil Sheet........................................................................................................ 74HvacSpecDefaults Sheet................................................................................................... 76PermissibleDuctThickness Sheet ...................................................................................... 78

Index..................................................................................................................................79


5/79

Preface


PrefaceThis document is a reference data guide for the SmartPlant 3D HVAC task. The

purpose of this document is to describe the reference data delivered with the software

for this task.

Reference data includes both catalog data and specification data. Catalog dataincludes the parts that you place in the model, such as piping components and

equipment. Specification data includes the rules that govern how those parts are

placed and connected.


6/79

Preface


SmartPlant 3D Documentation Set

The SmartPlant3D documentation set is available as Adobe

PDF files. The content

of the PDF files is the same content as online Help. To access these PDF documents

in the software, click Help > Printable Guides.

The documentation set is divided into four categories:

Administrative guides contain information about installing, configuring,customizing, and troubleshooting SmartPlant 3D.

User's guides provide command reference and how-to information forworking in each SmartPlant 3D task.

Reference data guides define the reference data workbooks. Not all taskshave reference data.

ISOGEN guides

Administrative Guides

Project Management User's Guide - Provides instructions for setting up the

databases, creating permission groups, backing up and restoring project data,assigning access permissions to the model, managing interference detection, defining

and managing locations for Global Workshare, controlling duplication and

consolidation of plants, tools for synchronization, regeneration of report databases,

and version upgrade.

SmartPlant 3D Database Integrity Guide- Provides information about the error

messages in the database integrity reports, including meaning, cause, and possible

corrective action.

SmartPlant 3D Global Workshare Guide- Provides instructions for setting up the

software and the databases to work in a workshare environment.

SmartPlant 3D Installation Guide- Provides instructions on installing and

configuring the software on both the client and server computers.

SmartPlant 3D/IntelliShip Programmer's Guide- Provides information about custom

commands, naming rules, and symbol programming.

SmartPlant 3D Integration Reference Guide- Provides information about installing,

configuring, and using SmartPlant 3D in an integrated environment.

SmartPlant 3D Interference Checking Guide- Provides information on installing,

configuring, and using the interference detection service.


7/79

Preface


SmartPlant 3D Interpreting Human Piping Specifications- Provides information

about how to interpret human piping specifications so that you can create the

corresponding piping specification in the software.

SmartPlant 3D Plant Design System (PDS) Guide- Provides all information needed

to use PDS with SmartPlant 3D. Topics include referencing active PDS projects inSmartPlant 3D, exporting PDS data and importing that data into SmartPlant 3D,

converting PDS reference data to SmartPlant 3D reference data, and converting

EDEN symbols to Visual Basic symbols.

SmartPlant 3D Release Bulletin- Provides what's new, hardware/software

requirements, and support information for the current release.

SmartPlant 3D Troubleshooting Guide- Provides information on how to resolve

errors that you may encounter in the software by documenting troubleshooting tips,

error messages, and to do list messages.

User's Guides

Catalog User's Guide- Provides information about viewing, editing, and creating

reference data and select lists (codelists).

Common User's Guide- Provides information about defining workspaces, navigating

in the model, precision input, filtering, manipulating views, and running reports.

Drawings and Reports User's Guide- Provides information about creating drawing

and report deliverables.

Electrical User's Guide- Provides information about routing electrical cable,

cableway, cable tray, and conduit.

Equipment and Furnishings User's Guide- Provides information about placing

equipment.

Grids User's Guide- Provides instructions for creating coordinate systems, elevation

grid planes, vertical grid planes, radial cylinders, radial planes, grid arcs, and grid

lines.

Hangers and Supports User's Guide- Provides instructions on placing piping, duct,

cableway, and conduit supports in the model.

HVAC User's Guide- Provides instructions for routing HVAC duct.

Piping User's Guide- Provides instructions for routing pipe and placing valves, taps,

and pipe joints.

Space Management User's Guide- Provides instructions for placing volumes (such as

drawing volumes, obstruction zones) in the model.


8/79

Preface


Structural Analysis User's Guide- Provides instructions for defining loads, load

cases, load combinations, and the importing and exporting of analytical data.

Structure User's Guide- Provides instructions for placing structural members such as:

beams, columns, braces, slabs, openings, stairs, ladders, equipment foundations, and

handrails.

Systems and Specifications User's Guide- Provides instructions for creating systems

and their hierarchies and selecting which specifications are available for each system

type.

SmartPlant 2D Symbols User's Guide- Provides instructions for creating cross

section symbols.

Reference Data Guides

Drawings and Reports Reference Data Guide- Provides information about reportsreference data.

Electrical Reference Data Guide- Provides information about electrical cable,

cableway, cable tray, and conduit reference data.

Equipment and Furnishings Reference Data Guide- Provides information about

equipment reference data and name rules.

Hangers and Supports Reference Data Guide- Provides information about hangersand supports reference data.

HVAC Reference Data Guide- Provides information about HVAC reference data.

Piping Reference Data Guide- Provides information about piping reference dataincluding piping specifications, piping specification rules, piping parts, piping

symbols, and name rules.

SmartPlant 2D Symbols Reference Data Guide- Provides information about the two-

dimensional symbols used in all tasks.

SmartPlant 3D Reference Data Guide- Provides instructions about the Bulkload

utility, codelists, and the reference data common to several disciplines.

SmartPlant 3D Symbols Reference Data Guide- Provides information about theVisual Basic Part Definition Wizard and the three-dimensional symbols used in all

tasks.

Space Management Reference Data Guide- Provides information about space

management reference data.


9/79

Preface


Structure Reference Data Guide- Provides information about structural reference

data and name rules.

ISOGEN Guides

AText Reference Guide- Provides information about alternative text for isometric

drawings. This guide is from Alias, the makers of ISOGEN

.

Option Switches Reference Guide- Provides information about the ISOGEN option

switches for isometric drawings. This guide is from Alias, the makers of ISOGEN.

Symbol Keys Reference Guide- Provides information about the symbol keys for

isometric drawings. This guide is from Alias, the makers of ISOGEN.


10/79

Preface


Documentation Comments

Send documentation comments or suggestions to [email protected].
mailto:[email protected]?subject=Documentation%20Commentsmailto:[email protected]?subject=Documentation%20Commentsmailto:[email protected]?subject=Documentation%20Commentsmailto:[email protected]?subject=Documentation%20Comments


11/79

Preface


What's New in HVAC Reference Data

Version 2007

No changes.


12/79

HVAC Reference Data: An Overview


HVAC Reference Data: An OverviewIn the HVAC task, reference data contains the rules and the parts necessary for

placement of routing in the duct system. These rules help in selecting the proper part

for the application and limiting parts availability based on routing conditions. HVACprovides duct-sizing capability to determine the proper duct sizes. This duct sizing

provides a list of duct cross sections and sizes valid for the specification for the

specific design criteria. A recommendation is to set preferred components as part of

the specification and as the defaults.

The HVAC software uses several standard data tables to produce correct modeling.

An administrator can add new rows to these tables or edit existing rows. After addingor editing rows, the administrator must bulk load the information into the Catalog

Database for the new information to take effect.

The interfaces for the HVAC and Cableway tasks are very similar. Reference data

determines the values that populate the various dialog boxes in both tasks. Comparedto Cableway, the values in HVAC deal more with duct components, like nozzles and

branches. For example, to create new routes, the reference data for the HVAC task

populates the New Duct Rundialog box, while the reference data for the Cableway

task populates the Create Cablewaydialog box.

The software selects default components based on your input during a session for

routing duct. For the proper configuration, the default or preferred components

include the duct cross section, duct size, duct material, material thickness or gage, and

the end or port connections.

Related Topics HVAC Sheets: An Overview, page 13


13/79

HVAC Sheets: An Overview


HVAC Sheets: An OverviewThe HVAC.xlsworkbook contains the reference data for the HVAC task. The sheets

that are unique to HVAC.xlsare described below. For more information on common

sheets, see the SmartPlant 3D Reference Data Guideaccessible from the Help >

Printable Guidescommand.

HvacSpec- Lists the specification names of HVAC specification objects. For more

information, see theHVACSpec Sheet, page 15.

ManualDamper- Defines reference data for manual dampers. For more information,

see theManualDamper Sheet, page 19.

MotorDamper- Defines the reference data for motor dampers. For more

information, see theMotorDamper Sheet, page 22.

Rect_FlatFlange- Defines reference data for rectangular flat flanges. For moreinformation, see theRect_FlatFlange Sheet, page 24.

Round_FlatFlange- Defines reference data for round flat flanges. For more

information, see theRound_FlatFlange Sheet, page 26.

Rect_FlatFlangeVA- Defines the reference data for rectangular flat flanges with

depth inclination. For more information, see theRect_FlatFlangeVA Sheet, page 28.

Round_FlatFlangeVA- Defines the reference data for round flat flanges with depth

inclination. For more information, see theRound_FlatFlangeVA Sheet, page 30

Round_Sleeve- Defines reference data for round sleeves. For more information, seetheRound_Sleeve Sheet, page 32.

Rect_Sleeve- Defines reference data for rectangular sleeves. For more information,

see theRect_Sleeve Sheet, page 34.

Round_Weld- Defines the reference data for round welded connections. For more

information, see theRound_Weld Sheet, page 36.

Rect_Weld- Defines the reference data for rectangular welded connections. For

more information, see theRect_Weld Sheet, page 37.

Round_Rivet- Defines the reference data for round riveted connections. For moreinformation, see theRound_Rivet Sheet, page 39.

Rect_Rivet- Defines the reference data for rectangular riveted connections. For more

information, see theRect_Rivet Sheet, page 40.

FlatOval_Weld- Defines the reference data for flat oval welded connections. For

more information, see the FlatOval_Weld Sheet, page 42.


14/79



FlatOval_Rivet- Defines the reference data for flat oval riveted connections. For

more information, see the FlatOval_Rivet Sheet, page 43.

DuctSmokeDetector- Defines the reference data for duct smoke detectors. For more

information, see theDuctSmokeDetector Sheet, page 45.

SamplingTube- Defines the reference data for sampling tubes. For moreinformation, see the SamplingTube Sheet, page 46.

Horn_Strobe- Defines the reference data for visible and audible warning signals.

For more information, see theHorn_Strobe Sheet, page 47.

SurfMountIcover- Defines reference data for surface-mounted covers. For more

information, see the SurfMountIcover Sheet, page 48.

SM1PipingTap- Defines reference data for one surface-mounted piping tap on an

HVAC duct for instrument assembly. Halfin is one-half inch nominal pipe diameter.

The part can be a piping 0.5" piping tap that is either socket- welded or female-threaded. The tap is mounted on a duct surface. For more information, see theSM1PipingTap Sheet, page 50.

SMRoundBranch- Defines the reference data for a surface-mounted round branch.

For more information, see the SMRoundBranch Sheet, page 52.

SMRectangularBranch- Defines the reference data for a surface-mounted

rectangular branch. For more information, see the SMRectangularBranch Sheet, page

53.

RoundTee- Defines reference data for round tees. For more information, see the

RoundTee Sheet, page 54.

RectTee- Defines the reference data for rectangular tees. For more information, see

theRectTee Sheet, page 56.

HVACElbow- Defines reference data for HVAC elbows. For more information, see

theHVACElbow Sheet, page 58.

RoundElbow- Defines the reference data for round elbows. For more information,

see theRoundElbow Sheet, page 60.

HsqrThroatElbow- Defines the reference data for square throat elbows. For more

information, see theHsqrThroatElbow Sheet, page 62.

BellMouthRound- Defines the reference data for a bell mouth. For more

information, see theBellMouthRound Sheet, page 64.

BellMouthRFO- Defines the reference data for a bell mouth with a flat oval outlet.

For more information, see theBellMouthRFO Sheet, page 65.


15/79



Division2- Defines reference data for a division feature, a component that divides the

HVAC rectangular duct into two ducts along the width of the duct. The divisionfeature has three ports: the original duct port and the resulting two ducts ports. For

more information, see theDivision2 Sheet, page 66.

DivisionW3- Defines the reference data for a division feature, a component thatdivides the HVAC rectangular duct into three ducts along the width of the duct. The

division feature has four ports: the original duct port and the resulting three duct

ports. For more information, see theDivisionW3 Sheet, page 68.

AirFilter- Defines the reference data for an air filter. For more information, see theAirFilter Sheet, page 70.

AirFilterHumidifier- Defines the reference data for an air filter humidifier. For

more information, see theAirFilterHumidifier Sheet, page 72.

AirCoolingCoil- Defines the reference data for an air cooling coil. For more

information, see theAirCoolingCoil Sheet, page 74.

HvacSpecDefaults- Lists the names of the specifications that you can use while

working with the HVAC reference data. For more information, see theHvacSpecDefaults Sheet, page 76.

PermissibleDuctThickness- Defines the reference data for permissible duct

thickness. For more information, see the PermissibleDuctThickness Sheet, page 78.

Related Topics

HVAC Reference Data: An Overview, page 12

HVACSpec Sheet

The HVACSpecsheet in the HVAC.xlsworkbook defines the specifications that are

available to you for HVAC routing. Currently, the workbook contains two

specifications: Spec-0and Spec-1.

SpecName- Type the specification name of the HVAC specification objects (for

example, Spec-0).

Service- Type a description of the service for the HVACSpec object. An example is

NoService.

PressureClass- Type the pressure class of the HvacSpec object. Examples are

LowPressureand MediumPressure.

HvacPartGenerationBasis- Specifies whether breaks on the feature boundary areenabled or disabled. Type 1to disable breaks or type 2to enable breaks. Based on this

value, the software determines if the continuous feature that you are routing is

terminated in case of a spec break.


16/79



LiningMaterial(Type/Grade)- Type a phrase that describes the type or grade of the

lining material.

InsulationMaterial(Type/Grade)- Type a phrase that describes the type or grade of

the insulation material.

DuctMaterial(Type/Grade)- Type a phrase that describes the type or grade of theduct material.

Note

The duct material is defined in the Materialsheet of the AllCommon.xlsfile.

Shapes- Type the name of the shape of the object. Options include Rectangular,

Round, Oval, and FlatOval.

PartNumber- Type the phrase that identifies the part number. Examples include:

PDS-100 PDS-150 PDS-200 PDS-250 PDS-300 PDS-350 PDS-400

RECTFF -Rectangular flat flange ROUNDFF- Round flat flange ROUNDSLEEVE RectSleeve- Rectangular sleeve B-100- Brepresents bend. TA-100X80- Trepresents tee. 100x80is a reducing tee. Header is

100mm diameter of the round tee, Width, Branchis 80mm to arrive atthe bend width.

HVACElbowFo DivisionW2 SM1PTapSWhalfin-Surface-mounted piping tap on a duct surface that

is socket-welded. halfinis one-half inch nominal pipe diameter

SM1PTapFThalfin- Surface-mounted piping tap on a duct surface that isfemale-threaded. halfinis one-half inch nominal pipe diameter

AirFilterHumidifier400x200x275


17/79



AirFilterHumidifier300x200x225 AirFilterHumidifier400x250x275 AirFilterHumidifier250x200x200 AirCoolingCoil400x200x350 AirCoolingCoil300x200x325 AirCoolingCoil400x250x350 AirCoolingCoil250x200x300 AirFilter400x200x180 AirFilter400x200x180 AirFilter300x200x150 AirFilter400x250x180 AirFilter250x200x120 MRD-URD-100 MRD-URD-150 MRD-URD-200 MRD-URD-250 MRD-URD-300 MRD-URD-350 MRD-URD-400 Icover400x600 Icover250x400 DivisionW3-01 SM-501-N SM-501-P RWX-N SL-2000-P STS-100 STS-50 STS-25 SHP24-1575W SHP24-1575R RoundWeld RectWeld


18/79



RoundRivet RectRivet FlatOvalWeld FlatOvalRivet Rect_SlopedFlange Round_SlopedFlange RectTee1 SMRectangularBranch1 SMRoundBranch1 HVACsqrThroatElbow01 Round Bellmouth 300x250 RoundxFlatOval Bellmouth 355x1450SectionName- Identifies the outfitting cross section (OCS). Examples are OCS-4X4,

OCS-6X4, OCS-8X4, OCS-6X6, OCS-10X4, OCS-8X6, OCS-7X7, OCS-14X4,OCS-8X7, OCS-16X4, OCS-10X6, OCS-8X8, OCS-9X7, OCS-12X6, OCS-10X7,

OCS-9X8, OCS-10X8, and OCS-14X6.

Note

The section name is defined in the OutfittingCrossSectionssheet of theAllCommon.xlsfile.

Related Topics

BellMouthRFO Sheet, page 65 BellMouthRound Sheet, page 64 DuctSmokeDetector Sheet, page 45 FlatOval_Rivet Sheet, page 43 FlatOval_Weld Sheet, page 42 Horn_Strobe Sheet, page 47 HsqrThroatElbow Sheet, page 62 HVAC Sheets: An Overview, page 13 HVACElbow Sheet, page 58 ManualDamper Sheet, page 19 PermissibleDuctThickness Sheet, page 78

Rect_FlatFlange Sheet, page 24 Rect_FlatFlangeVA Sheet, page 28 Rect_Rivet Sheet, page 40 Rect_Sleeve Sheet, page 34 Rect_Weld Sheet, page 37 RectTee Sheet, page 56 Round_FlatFlange Sheet, page 26 Round_FlatFlangeVA Sheet, page 30


19/79



Round_Rivet Sheet, page 39 Round_Sleeve Sheet, page 32 Round_Weld Sheet, page 36 RoundElbow Sheet, page 60 RoundTee Sheet, page 54

SamplingTube Sheet, page 46 SMRectangularBranch Sheet, page 53 SMRoundBranch Sheet, page 52 SurfMountIcover Sheet, page 48

ManualDamper Sheet

The ManualDampersheet in the HVAC.xlsworkbook defines the manual dampers

that you want in the Catalog.

PartNumber- Type the part number assigned to the manual damper. The software

uses the part number at placement when the part name is automatically generated. Anexample is PDS-100.

Tip

Part numbers for manual dampers must be unique throughout the entireCatalog.

SymbolDefinition- Type the definition of the Visual Basic symbol that you arecreating for the manual damper. An example is

PDSHRoundDamper.HRoundDamper.

FaceWidth- Type the width of the face for the damper.

FaceDepth- Type the face depth for the damper.

ComponentType- Type the component type for the damper.

PartDescription- Type a description for the damper. An example is Manual

Damper Part.

DryWeight- Type a dry weight for the damper.

DrycogX- Type the offset distance along the x-axis for the dry center of gravity of

the damper.

DrycogY- Type the offset distance along the y-axis for the dry center of gravity of

the damper.

DryCogZ- Type the offset distance along the z-axis for the dry center of gravity of

the damper.

WaterWeight- Type the water weight of the damper.


20/79



WaterCogX- Type the offset distance along the x-axis for the wet center of gravity

of the damper.

WaterCogY- Type the offset distance along the y-axis for the wet center of gravity

of the damper.

WaterCogZ- Type the offset distance along the z-axis for the wet center of gravityof the damper.

Width- Type the width of the damper.

DamperLength- Type the length for the damper.

Thickness- Type the thickness for the damper.

FlangeWidth- Type the width of the flange for the damper.

Tip

For the remaining properties, (i)indicates an integer corresponding to anozzle number assigned to the cross section. This method avoids a lengthy

listing for all possibilities, like Nozzle(1):CrossSection,Nozzle(2):CrossSection, and Nozzle(3):CrossSectionfor three possible

nozzles. When you type the nozzle properties in the workbook, substitute

a number for ito assign the nozzle to the appropriate property.

Nozzle(i):CrossSection- Type the related CrossSection object for the port as listed

on the HvacSpecsheet.

Nozzle(i):EndPrep- Type the coded end preparation for Nozzle 1. The

AllCodeLists.xlsworkbook contains mappings between numbers and components.For example, the number 11in the Nozzle EndPrepcolumn on the ManualDamper

sheet corresponds to the flat-face flanged end, as specified in the AllCodeLists.xls

workbook.

Nozzle(i):Thickness- Type the thickness of the nozzle port. The number of actual

nozzles present on a cableway run can vary.

Nozzle(i):FlangeWidth- Type the flange width for the nozzle.

Nozzle(i):FlowDirection- Type the flow direction for the nozzle.

Nozzle(i):PortDepth- Type the depth of the port for the nozzle.

Nozzle(i):CptOffset- Type the offset value for the component.


21/79



Related Topics

BellMouthRFO Sheet, page 65 BellMouthRound Sheet, page 64 DuctSmokeDetector Sheet, page 45 FlatOval_Rivet Sheet, page 43

FlatOval_Weld Sheet, page 42 Horn_Strobe Sheet, page 47 HsqrThroatElbow Sheet, page 62 HVAC Sheets: An Overview, page 13 HVACElbow Sheet, page 58 HVACSpec Sheet, page 15 HvacSpecDefaults Sheet, page 76 PermissibleDuctThickness Sheet, page 78 Rect_FlatFlange Sheet, page 24 Rect_FlatFlangeVA Sheet, page 28 Rect_Rivet Sheet, page 40

Rect_Sleeve Sheet, page 34 Rect_Weld Sheet, page 37 RectTee Sheet, page 56 Round_FlatFlange Sheet, page 26 Round_FlatFlangeVA Sheet, page 30 Round_Rivet Sheet, page 39 Round_Sleeve Sheet, page 32 Round_Weld Sheet, page 36 RoundElbow Sheet, page 60 RoundTee Sheet, page 54 SamplingTube Sheet, page 46 SMRectangularBranch Sheet, page 53 SMRoundBranch Sheet, page 52 SurfMountIcover Sheet, page 48


22/79



MotorDamper Sheet

The MotorDampersheet in the HVAC.xlsworkbook defines the motorized dampers


PartNumber- Type the part number assigned to the motorized damper. The softwareuses the part number at placement when the part name is automatically generated. Anexample is MRD-URD-100(MRDrepresents motorized damper. URDrepresents

non-motorized damper.)

Tip

Part numbers for Motor dampers must be unique throughout the entireCatalog.

SymbolDefinition- Type the definition of the Visual Basic symbol that you are

creating for the Motor damper. An example is

PDSMotorRoundDamper.CMotorRoundDamper.

FaceWidth- Type the width of the face for the damper.

FaceDepth- Type the face depth for the damper.

ComponentType- Type the component type for the damper.

PartDescription- Type a description for the damper. An example is Motorized

Round Damper 100mm diameter model URD Ultra-Zone.

Width- Type the width of the damper.

DamperLength- Type the length for the damper.

Thickness- Type the thickness for the damper.

FlangeWidth- Type the width of the flange for the damper.

Tip



nozzles. When you type the nozzle properties in the workbook, substitutea number for ito assign the nozzle to the appropriate property.

Nozzle(i):CrossSection- Type the related CrossSection object for the port as listed

on the HvacSpecsheet.


23/79



Nozzle(i):EndPrep- Type the coded end preparation for Nozzle 1. The

AllCodeLists.xlsworkbook contains mappings between numbers and components.For example, the number 11in the Nozzle EndPrepcolumn on the MotorDamper

sheet corresponds to the flat-face flanged end, as specified in the AllCodeLists.xls

workbook.

Nozzle(i):Thickness- Type the thickness of the nozzle port. The number of actual

nozzles present on a cableway run can vary.





Related Topics BellMouthRFO Sheet, page 65 BellMouthRound Sheet, page 64 DuctSmokeDetector Sheet, page 45 FlatOval_Rivet Sheet, page 43 FlatOval_Weld Sheet, page 42 Horn_Strobe Sheet, page 47 HsqrThroatElbow Sheet, page 62 HVAC Sheets: An Overview, page 13 HVACElbow Sheet, page 58 HVACSpec Sheet, page 15 HvacSpecDefaults Sheet, page 76 PermissibleDuctThickness Sheet, page 78 Rect_FlatFlange Sheet, page 24 Rect_FlatFlangeVA Sheet, page 28 Rect_Rivet Sheet, page 40 Rect_Sleeve Sheet, page 34 Rect_Weld Sheet, page 37 RectTee Sheet, page 56 Round_FlatFlange Sheet, page 26 Round_FlatFlangeVA Sheet, page 30 Round_Rivet Sheet, page 39 Round_Sleeve Sheet, page 32 Round_Weld Sheet, page 36 RoundElbow Sheet, page 60 RoundTee Sheet, page 54 SamplingTube Sheet, page 46 SMRectangularBranch Sheet, page 53 SMRoundBranch Sheet, page 52 SurfMountIcover Sheet, page 48


24/79



Rect_FlatFlange Sheet

The Rect_FlatFlangesheet in the HVAC.xlsworkbook organizes facts for

rectangular flat flanges.

PartNumber- Type the part number for the flange. An example is RECTFFforrectangular flat flange.

Tip

Part numbers for rectangular flat flanges must be unique throughout theentire Catalog.

FaceDepth- Type the face depth for the coil.

FaceWidth- Type the face width for the coil.

ComponentType- Type the component type for the rectangular flat flange.

PartDescription- Type a description for the rectangular flat flange.

SymbolDefinition- Type the symbol definition for the rectangular flat flange.

Width- Type the width of the duct.

Depth- Type the depth of the duct.

Clearance- Type the clearance for the rectangular flat flange.

FlangeWidth- Type the width of the flange.

Thickness- Type the thickness for the flange.

CompressedGasket- Type the thickness for the compressed gasket.

Tip




a number for ito assign the nozzle to the appropriate property.Nozzle(i):CrossSection-Type the related CrossSection object for the port.

Nozzle(i):EndPrep- Type the coded end preparation for the nozzle. Examples of end

preparations include Threaded, Screwed, Plain End, Welded, Bolted, Female,

Male, and Ferule. In the reference data, a number represents each type of end

preparation (for example, 1for Threaded, 2for Screwedand so on).


25/79


26/79



Round_FlatFlange Sheet

The Round_FlatFlangesheet in the HVAC.xlsworkbook defines the round flat

flanges that you want in the Catalog.

PartNumber- Type the part number for the flange. An example is ROUNDFFforround flat flange.

Tip

Part numbers for round flat flanges must be unique throughout the entireCatalog.

SymbolDefinition- Type the symbol definition for the round flat flange. An example

is PDSRoundFlatFlange.HROUNDFF.



ComponentType- Type the component type for the round flat flange.

PartDescription- Type a description for the round flat flange.


Clearance- Type the clearance for the round flat flange.




Tip

For the remaining properties, (i)indicates an integer corresponding to anozzle number assigned to the cross section. This method avoids a lengthylisting for all possibilities, like Nozzle(1):CrossSection,

Nozzle(2):CrossSection, and Nozzle(3):CrossSectionfor three possible


Nozzle(i):CrossSection- Type the related CrossSection object for the port.





Nozzle(i):Thickness- Type the thickness of for the particular nozzle port.


27/79





Nozzle(i):PortDepth- Type the depth of the port for nozzle.


Related Topics

BellMouthRFO Sheet, page 65 BellMouthRound Sheet, page 64 DuctSmokeDetector Sheet, page 45 FlatOval_Rivet Sheet, page 43 FlatOval_Weld Sheet, page 42 Horn_Strobe Sheet, page 47 HsqrThroatElbow Sheet, page 62 HVAC Sheets: An Overview, page 13 HVACElbow Sheet, page 58 HVACSpec Sheet, page 15 HvacSpecDefaults Sheet, page 76 ManualDamper Sheet, page 19 PermissibleDuctThickness Sheet, page 78 Rect_FlatFlange Sheet, page 24 Rect_FlatFlangeVA Sheet, page 28 Rect_Rivet Sheet, page 40 Rect_Sleeve Sheet, page 34 Rect_Weld Sheet, page 37 RectTee Sheet, page 56 Round_FlatFlangeVA Sheet, page 30 Round_Rivet Sheet, page 39 Round_Sleeve Sheet, page 32 Round_Weld Sheet, page 36 RoundElbow Sheet, page 60 RoundTee Sheet, page 54 SamplingTube Sheet, page 46 SMRectangularBranch Sheet, page 53 SMRoundBranch Sheet, page 52 SurfMountIcover Sheet, page 48


28/79



Rect_FlatFlangeVA Sheet

The Rect_FlatFlangeVAsheet in the HVAC.xlsworkbook organizes facts for

rectangular sloped flanges.

PartNumber- Type the part number for the flange. An example isRect_SlopedFlangefor rectangular sloped flange.

Tip













Tip




a number for ito assign the nozzle to the appropriate property.Nozzle(i):CrossSection-Type the related CrossSection object for the port.






29/79



Nozzle(i):Thickness- Type the thickness of the nozzle port.





Related Topics

BellMouthRFO Sheet, page 65 BellMouthRound Sheet, page 64 DuctSmokeDetector Sheet, page 45 FlatOval_Rivet Sheet, page 43 FlatOval_Weld Sheet, page 42 Horn_Strobe Sheet, page 47 HsqrThroatElbow Sheet, page 62 HVAC Sheets: An Overview, page 13 HVACElbow Sheet, page 58 HVACSpec Sheet, page 15 HvacSpecDefaults Sheet, page 76 ManualDamper Sheet, page 19 PermissibleDuctThickness Sheet, page 78 Rect_Rivet Sheet, page 40 Rect_Sleeve Sheet, page 34 Rect_Weld Sheet, page 37 RectTee Sheet, page 56

Round_FlatFlange Sheet, page 26 Round_Rivet Sheet, page 39 Round_Sleeve Sheet, page 32 Round_Weld Sheet, page 36 RoundElbow Sheet, page 60 RoundTee Sheet, page 54 SamplingTube Sheet, page 46 SMRectangularBranch Sheet, page 53 SMRoundBranch Sheet, page 52 SurfMountIcover Sheet, page 48


30/79



Round_FlatFlangeVA Sheet

The Round_FlatFlangeVAsheet in the HVAC.xlsworkbook organizes facts for

round flat flanges with depth inclination.

PartNumber- Type the part number for the flange. An example isRound_SlopedFlangefor round sloped flange.

Tip












Tip





Nozzle(i):CrossSection-Type the related CrossSection object for the port.

Nozzle(i):EndPrep- Type the coded end preparation for the nozzle. Examples of endpreparations include Threaded, Screwed, Plain End, Welded, Bolted, Female,





31/79







Related Topics

BellMouthRFO Sheet, page 65 BellMouthRound Sheet, page 64 DuctSmokeDetector Sheet, page 45 FlatOval_Rivet Sheet, page 43 FlatOval_Weld Sheet, page 42 Horn_Strobe Sheet, page 47 HsqrThroatElbow Sheet, page 62 HVAC Sheets: An Overview, page 13 HVACElbow Sheet, page 58 HVACSpec Sheet, page 15 HvacSpecDefaults Sheet, page 76 ManualDamper Sheet, page 19 PermissibleDuctThickness Sheet, page 78 Rect_Rivet Sheet, page 40 Rect_Sleeve Sheet, page 34 Rect_Weld Sheet, page 37 RectTee Sheet, page 56 Round_FlatFlange Sheet, page 26 Round_Rivet Sheet, page 39 Round_Sleeve Sheet, page 32 Round_Weld Sheet, page 36 RoundElbow Sheet, page 60 RoundTee Sheet, page 54 SamplingTube Sheet, page 46 SMRectangularBranch Sheet, page 53 SMRoundBranch Sheet, page 52 SurfMountIcover Sheet, page 48


32/79



Round_Sleeve Sheet

The Round_Sleevesheet in the HVAC.xlsworkbook defines the round sleeves that

you want in the Catalog.

PartNumber- Type the part number for the sleeve. An example isROUNDSLEEVEfor round sleeve.

Tip

Part numbers for round sleeves must be unique throughout the entireCatalog.

FaceDepth- Type the face depth for the object.

FaceWidth- Type the face width for the object.

ComponentType- Type the component type for the round sleeve.

PartDescription- Type a description for the round sleeve.

SymbolDefinition- Type the symbol definition for the round sleeve. An example is

PDSHRoundSleeve.HROUNDSLV.


Clearance- Type the clearance for the round sleeve.

Length- Type the length of the round sleeve.

Thickness- Type the thickness for the sleeve.

Tip











Nozzle(i):FlangeWidth- Type the sleeve width for the nozzle.


33/79






Related Topics BellMouthRound Sheet, page 64 HsqrThroatElbow Sheet, page 62 HVAC Sheets: An Overview, page 13 HVACElbow Sheet, page 58 HVACSpec Sheet, page 15 HvacSpecDefaults Sheet, page 76 ManualDamper Sheet, page 19 Rect_FlatFlange Sheet, page 24 Rect_FlatFlangeVA Sheet, page 28 Rect_Sleeve Sheet, page 34 RectTee Sheet, page 56 Round_FlatFlange Sheet, page 26 Round_FlatFlangeVA Sheet, page 30 RoundElbow Sheet, page 60 RoundTee Sheet, page 54 SMRectangularBranch Sheet, page 53 SMRoundBranch Sheet, page 52 SurfMountIcover Sheet, page 48


34/79



Rect_Sleeve Sheet

The Rect_Sleevesheet in the HVAC.xlsworkbook organizes facts for rectangular

sleeves.

PartNumber- Type the part number for the sleeve. An example is RECTSLEEVEfor rectangular sleeve.

Tip

Part numbers for rectangular sleeves must be unique throughout the entireCatalog.



ComponentType- Type the component type for the rectangular sleeve.

PartDescription- Type a description for the rectangular sleeve.

SymbolDefinition- Type the symbol definition for the rectangular sleeve. An

example is PBSHRectSleeve.HRECTV.



Clearance- Type the clearance for the rectangular sleeve.

Length- Type the length of the rectangular sleeve.

Thickness- Type the thickness for the sleeve.

Tip

For the remaining properties, (i)indicates an integer corresponding to anozzle number assigned to the cross section. This method avoids a lengthylisting for all possibilities, like Nozzle(1):CrossSection,



Nozzle(i):EndPrep- Type the coded end preparation for the particular nozzle.

Examples of end preparations include Threaded, Screwed, Plain End, Welded,

Bolted, Female, Male, and Ferule. In the reference data, a number represents each

type of end preparation (for example, 1for Threaded, 2for Screwedand so on).




35/79


36/79



Round_Weld Sheet

The Round_Sleevesheet in the HVAC.xlsworkbook defines the round welds that


PartNumber- Type the part number for the weld. An example is RoundWeldforround weld.

Tip




ComponentType- Type the component type for the round weld.

PartDescription- Type a description for the round weld.

SymbolDefinition- Type the symbol definition for the round weld. An example is

SP3DHVACRoundWeld.CHVACRoundWeld.


Tip







preparations include Threaded, Screwed, Plain End, Welded, Bolted, Female,Male, and Ferule. In the reference data, a number represents each type of end








37/79



Related Topics

BellMouthRound Sheet, page 64 HsqrThroatElbow Sheet, page 62 HVAC Sheets: An Overview, page 13 HVACElbow Sheet, page 58

HVACSpec Sheet, page 15 HvacSpecDefaults Sheet, page 76 ManualDamper Sheet, page 19 Rect_FlatFlange Sheet, page 24 Rect_FlatFlangeVA Sheet, page 28 Rect_Sleeve Sheet, page 34 RectTee Sheet, page 56 Round_FlatFlange Sheet, page 26 Round_FlatFlangeVA Sheet, page 30 RoundElbow Sheet, page 60 RoundTee Sheet, page 54

SMRectangularBranch Sheet, page 53 SMRoundBranch Sheet, page 52 SurfMountIcover Sheet, page 48

Rect_Weld Sheet

The Rect_Sleevesheet in the HVAC.xlsworkbook defines the rectangular welds that


PartNumber- Type the part number for the weld. An example is RectWeldfor

rectangular weld.

Tip




ComponentType- Type the component type for the weld.

PartDescription- Type a description for the weld.

SymbolDefinition- Type the symbol definition for the weld. An example is

SP3DHVACRectWeld.CHVACRectWeld.




38/79



Tip


listing for all possibilities, like Nozzle(1):CrossSection,












Related Topics

BellMouthRound Sheet, page 64 HsqrThroatElbow Sheet, page 62 HVAC Sheets: An Overview, page 13 HVACElbow Sheet, page 58 HVACSpec Sheet, page 15 HvacSpecDefaults Sheet, page 76 ManualDamper Sheet, page 19 Rect_FlatFlange Sheet, page 24 Rect_FlatFlangeVA Sheet, page 28 Rect_Sleeve Sheet, page 34 RectTee Sheet, page 56 Round_FlatFlange Sheet, page 26 Round_FlatFlangeVA Sheet, page 30 RoundElbow Sheet, page 60 RoundTee Sheet, page 54 SMRectangularBranch Sheet, page 53 SMRoundBranch Sheet, page 52 SurfMountIcover Sheet, page 48


39/79



Round_Rivet Sheet

The Round_Rivetsheet in the HVAC.xlsworkbook defines the round rivet

connections that you want in the Catalog.

PartNumber- Type the part number for the rivet connections. An example isRoundRivetfor round rivet.

Tip

Part numbers for round rivets must be unique throughout the entireCatalog.



ComponentType- Type the component type for the round rivet.

PartDescription- Type a description for the round rivet.

SymbolDefinition- Type the symbol definition for the round rivet. An example is

SP3DHVACRoundRivet.CHVACRoundRivet.


Tip














40/79




Related Topics

BellMouthRound Sheet, page 64 HsqrThroatElbow Sheet, page 62

HVAC Sheets: An Overview, page 13 HVACElbow Sheet, page 58 HVACSpec Sheet, page 15 HvacSpecDefaults Sheet, page 76 ManualDamper Sheet, page 19 Rect_FlatFlange Sheet, page 24 Rect_FlatFlangeVA Sheet, page 28 Rect_Sleeve Sheet, page 34 RectTee Sheet, page 56 Round_FlatFlange Sheet, page 26 Round_FlatFlangeVA Sheet, page 30

RoundElbow Sheet, page 60 RoundTee Sheet, page 54 SMRectangularBranch Sheet, page 53 SMRoundBranch Sheet, page 52 SurfMountIcover Sheet, page 48

Rect_Rivet Sheet

The Rect_Rivetsheet in the HVAC.xlsworkbook defines the rectangular rivets that


PartNumber- Type the part number for the rivet. An example is RectRivetforrectangular rivet.

Tip

Part numbers for rectangular rivets must be unique throughout the entireCatalog.



ComponentType- Type the component type for the rivet.

PartDescription- Type a description for the rivet.

SymbolDefinition- Type the symbol definition for the rivet. An example is

SP3DHVACRectRivet.CHVACRectRivet.



41/79




Tip


listing for all possibilities, like Nozzle(1):CrossSection,Nozzle(2):CrossSection, and Nozzle(3):CrossSectionfor three possiblenozzles. When you type the nozzle properties in the workbook, substitute











Related Topics



42/79



FlatOval_Weld Sheet

The FlatOval_Sleevesheet in the HVAC.xlsworkbook defines the flat oval welds


PartNumber- Type the part number for the weld. An example is FlatOvalWeldforflat oval weld.

Tip

Part numbers for flat oval welds must be unique throughout the entireCatalog.



ComponentType- Type the component type for the weld.

PartDescription- Type a description for the weld.

SymbolDefinition- Type the symbol definition for the weld. An example is

SP3DHVACFlatOvalWeld.CFlatOvWeld.



Tip


listing for all possibilities, like Nozzle(1):CrossSection,

Nozzle(2):CrossSection, and Nozzle(3):CrossSectionfor three possiblenozzles. When you type the nozzle properties in the workbook, substitute












43/79


44/79




Tip


listing for all possibilities, like Nozzle(1):CrossSection,Nozzle(2):CrossSection, and Nozzle(3):CrossSectionfor three possiblenozzles. When you type the nozzle properties in the workbook, substitute











Related Topics



45/79



DuctSmokeDetector Sheet

The DuctSmokeDetectorsheet in the HVAC.xlsworkbook defines the duct smoke

detectors that you want in the Catalog.

PartNumber- Type the part number for the object. An example is SL-2000-Pfor anSL-2000 Photoelectric detector.

Tip

Part numbers must be unique throughout the entire Catalog.FaceDepth- Type the face depth for the object.


ComponentType- Type the component type for the object.

PartDescription- Type a description for the object.

SymbolDefinition- Type the symbol definition for the object. An example is

GSCADHVACSurfMount.Cover.

CrossSectionShape- Type the cross section shape for the object.

Thickness- Type the thickness for the object.

Cover- Type the cover dimension for the object.

Holelength- Type the hole length dimension for the object.

Holebreadth- Type the hole breadth dimension for the object.

Covercornerradius- Type the cover corner radius for the object.

Gripdistance- Type the grip distance dimension for the object.

Handlelength- Type the handle length dimension for the object.

Related Topics

BellMouthRound Sheet, page 64 HsqrThroatElbow Sheet, page 62 HVAC Sheets: An Overview, page 13 HVACElbow Sheet, page 58 HVACSpec Sheet, page 15 HvacSpecDefaults Sheet, page 76 ManualDamper Sheet, page 19 Rect_FlatFlange Sheet, page 24 Rect_FlatFlangeVA Sheet, page 28 Rect_Sleeve Sheet, page 34


46/79



RectTee Sheet, page 56 Round_FlatFlange Sheet, page 26 Round_FlatFlangeVA Sheet, page 30 RoundElbow Sheet, page 60 RoundTee Sheet, page 54


SamplingTube Sheet

The SamplingTubesheet in the HVAC.xlsworkbook defines the sampling tubes that


PartNumber- Type the part number for the object. An example is STS-100for an

STS-10 foot long sampling tube.

Tip

Part numbers must be unique throughout the entire Catalog.PartDescription- Type a description for the object.

Related Topics

BellMouthRound Sheet, page 64 HsqrThroatElbow Sheet, page 62 HVAC Sheets: An Overview, page 13 HVACElbow Sheet, page 58 HVACSpec Sheet, page 15 HvacSpecDefaults Sheet, page 76 ManualDamper Sheet, page 19 Rect_FlatFlange Sheet, page 24 Rect_FlatFlangeVA Sheet, page 28 Rect_Sleeve Sheet, page 34 RectTee Sheet, page 56 Round_FlatFlange Sheet, page 26 Round_FlatFlangeVA Sheet, page 30 RoundElbow Sheet, page 60 RoundTee Sheet, page 54



47/79



Horn_Strobe Sheet

The Horn_Strobesheet in the HVAC.xlsworkbook defines the horn/strobe warning

signals that you want in the Catalog.

PartNumber- Type the part number for the object. An example is SHP24-1575Wfor a white 24VDC horn/strobe smoke visual and audible warning signal.

Tip

Part numbers must be unique throughout the entire Catalog.PartDescription- Type a description for the object.

Related Topics



48/79



SurfMountIcover Sheet

The SurfMountIcoversheet in the HVAC.xlsworkbook defines the surface-

mounted inspection covers that you want in the Catalog.

PartNumber- Type the part number for the surface-mounted inspection cover. Anexample is Icover400x600.

Tip

Part numbers for surface-mounted inspection covers must be uniquethroughout the entire Catalog.

FaceDepth- Type the face depth for the cover.

FaceWidth- Type the face width for the cover.

ComponentType- Type the component type for the surface-mounted component.

PartDescription- Type a description for the surface-mounted cover. An example is

Inspection cover.

SymbolDefinition- Type the symbol definition for the surface-mounted component.

An example is PBSHVACSurfMount.Cover.

CrossSectionShape- Type the designation for the shape of the cross section.

Examples of possible shapes are Rectangular, Round, Flat Oval, and U-Shape.

Thickness- Type the correct measurement value for thickness of the surface-

mounted component.

cover- Type the correct measurement value for the cover.

holelength- Type the correct measurement value for holes in the cover.

holebreadth- Type the correct measurement value for breadth of holes in the cover.

covercornerradius- Type the name of the cross section associated with the surface-

mounted cover.

gripdistance- Type the value for the grip distance for the surface-mounted cover.


49/79


50/79



SM1PipingTap Sheet

The SM1PipingTapsheet in the HVAC.xlsworkbook defines the reference data for

one surface-mounted piping tap on an HVAC duct for instrument assembly.

PartNumber- Type the part number for the surface-mounted piping tap. Examplesinclude:

SM1PTapSWhalfin- A surface-mounted piping tap that is socket-welded(represented by SW) and has .5" (represented by halfin) nominal piping

diameter

SM1PTapFThalfin- A surface-mounted piping tap that is female-threaded (represented by FT) and has .5" (represented by halfin) nominal

piping diameter

Tip

Part numbers for surface-mounted piping taps must be unique throughoutthe entire Catalog.

ComponentType- Type the component type for the piping tap.

PartDescription- Type a description for the piping tap. An example is Rect_Sleeve.

SymbolDefinition- Type the symbol definition for the piping tap. An example is

PBSHRectSleeve.HRECTSLV.

Tip

For the remaining properties, (i)indicates an integer corresponding to anozzle number assigned to the piping tap. This method avoids a lengthylisting for all possibilities, like Nozzle(1):CrossSection,

Nozzle(2):CrossSection, and Nozzle(3):CrossSectionfor three possiblenozzles. When you type the nozzle properties in the workbook, substitute


Nozzle(i):Npd- Type the nominal piping diameter for the nozzle port.

Nozzle(i):NpdUnitType- Type the unit type for the nozzle port.



Male, and Ferule. In the reference data, a number represents each type of endpreparation (for example, 1for Threaded, 2for Screwedand so on).

Nozzle(i):EndStandard- Type the coded end standard for the nozzle.

Nozzle(i):ScheduleThickness- Type the schedule thickness for the nozzle.

Nozzle(i):PressureRating- Type the pressure rating for the nozzle.


51/79



Nozzle(i)FlowDirection- Type the flow direction for the nozzle.

Nozzle(i)PipingPointBasis- Type the piping point basis for the nozzle.

Related Topics

BellMouthRFO Sheet, page 65 BellMouthRound Sheet, page 64 DuctSmokeDetector Sheet, page 45 FlatOval_Rivet Sheet, page 43 FlatOval_Weld Sheet, page 42 Horn_Strobe Sheet, page 47 HsqrThroatElbow Sheet, page 62 HVAC Sheets: An Overview, page 13 HVACElbow Sheet, page 58 HVACSpec Sheet, page 15 HvacSpecDefaults Sheet, page 76 ManualDamper Sheet, page 19 PermissibleDuctThickness Sheet, page 78 Rect_FlatFlange Sheet, page 24 Rect_FlatFlangeVA Sheet, page 28 Rect_Rivet Sheet, page 40 Rect_Sleeve Sheet, page 34 Rect_Weld Sheet, page 37 RectTee Sheet, page 56 Round_FlatFlange Sheet, page 26 Round_FlatFlangeVA Sheet, page 30 Round_Rivet Sheet, page 39 Round_Sleeve Sheet, page 32 Round_Weld Sheet, page 36 RoundElbow Sheet, page 60 RoundTee Sheet, page 54 SamplingTube Sheet, page 46 SMRectangularBranch Sheet, page 53 SMRoundBranch Sheet, page 52


52/79



SMRoundBranch Sheet

The SMRoundBranchsheet in the HVAC.xlsworkbook defines the surface

mounted components with round nozzles that you want in the Catalog.

PartNumber- Type the part number for the round branch. An example isSMRoundBranch1.


FaceWidth- Type the face width of the damper for the object.

FaceDepth- Type the face depth of the damper for the object.

ComponentType- Type the component type for the round tee.

SymbolDefinition- Type the symbol definition for the round tee. An example is

SP3DHvacSMRoundB.CHvacSMRoundB.

Related Topics

BellMouthRFO Sheet, page 65 BellMouthRound Sheet, page 64 DuctSmokeDetector Sheet, page 45 FlatOval_Rivet Sheet, page 43 FlatOval_Weld Sheet, page 42 Horn_Strobe Sheet, page 47 HsqrThroatElbow Sheet, page 62 HVAC Sheets: An Overview, page 13

HVACElbow Sheet, page 58 HVACSpec Sheet, page 15 HvacSpecDefaults Sheet, page 76 ManualDamper Sheet, page 19 PermissibleDuctThickness Sheet, page 78 Rect_FlatFlange Sheet, page 24 Rect_FlatFlangeVA Sheet, page 28 Rect_Rivet Sheet, page 40 Rect_Sleeve Sheet, page 34 Rect_Weld Sheet, page 37 Round_FlatFlange Sheet, page 26

Round_FlatFlangeVA Sheet, page 30 Round_Rivet Sheet, page 39 Round_Sleeve Sheet, page 32 Round_Weld Sheet, page 36 RoundElbow Sheet, page 60 SamplingTube Sheet, page 46 SurfMountIcover Sheet, page 48


53/79



SMRectangularBranch Sheet

The SMRectangularBranchsheet in the HVAC.xlsworkbook defines the surface

mounted components with rectangular nozzles that you want in the Catalog.

PartNumber- Type the part number for the round branch. An example isSMRectangularBranch1.






SP3DHvacSMRB.CHvacSMRB.

Related Topics

BellMouthRFO Sheet, page 65 BellMouthRound Sheet, page 64 DuctSmokeDetector Sheet, page 45 FlatOval_Rivet Sheet, page 43 FlatOval_Weld Sheet, page 42 Horn_Strobe Sheet, page 47 HsqrThroatElbow Sheet, page 62 HVAC Sheets: An Overview, page 13

HVACElbow Sheet, page 58 HVACSpec Sheet, page 15 HvacSpecDefaults Sheet, page 76 ManualDamper Sheet, page 19 PermissibleDuctThickness Sheet, page 78 Rect_FlatFlange Sheet, page 24 Rect_FlatFlangeVA Sheet, page 28 Rect_Rivet Sheet, page 40 Rect_Sleeve Sheet, page 34 Rect_Weld Sheet, page 37 Round_FlatFlange Sheet, page 26

Round_FlatFlangeVA Sheet, page 30 Round_Rivet Sheet, page 39 Round_Sleeve Sheet, page 32 Round_Weld Sheet, page 36 RoundElbow Sheet, page 60 SamplingTube Sheet, page 46 SurfMountIcover Sheet, page 48


54/79



RoundTee Sheet

The RoundTeesheet in the HVAC.xlsworkbook defines the round tees that you

want in the Catalog.

PartNumber- Type the part number for the round tee. An example is TA-100X80.

PartDescription- Type a description for the round tee.

FaceWidth- Type the face width of the damper for the round tee.

FaceDepth- Type the face depth of the damper for the round tee.

ComponentType- Type the component type for the round tee.


PBSHRoundRTE.HRoundRTE.


BWidth- Type the width of the bend.

HLength- Type the length for the round tee.

BLength- Type the length of the bend.

Tip





Nozzle(i):CrossSection- Type the related CrossSection object for the port in the

particular nozzle.




Nozzle(i):Thickness- Type the thickness of the nozzle.





55/79


56/79



RectTee Sheet

The RectTeesheet in the HVAC.xlsworkbook defines the rectangular tees that you


PartNumber- Type the part number for the round tee. An example is RectTee1.





SymbolDefinition- Type the symbol definition for the object. An example is

SP3DHRectRTE.HRectRTE.


Depth- Type the depth of the duct

BWidth- Type the width of the bend.

BDepth- Type the depth of the bend.

HLength- Type the length for the round tee.

BLength- Type the length of the bend.

PlaneOfBranch- Type the angle of the bend.

Tip





Nozzle(i):CrossSection- Type the related CrossSection object for the port in the

particular nozzle.




Nozzle(i):Thickness- Type the thickness of the nozzle.


57/79







Related Topics

BellMouthRFO Sheet, page 65 BellMouthRound Sheet, page 64 DuctSmokeDetector Sheet, page 45 FlatOval_Rivet Sheet, page 43 FlatOval_Weld Sheet, page 42 Horn_Strobe Sheet, page 47 HsqrThroatElbow Sheet, page 62 HVAC Sheets: An Overview, page 13 HVACElbow Sheet, page 58 HVACSpec Sheet, page 15 HvacSpecDefaults Sheet, page 76 ManualDamper Sheet, page 19 PermissibleDuctThickness Sheet, page 78 Rect_FlatFlange Sheet, page 24 Rect_FlatFlangeVA Sheet, page 28 Rect_Rivet Sheet, page 40 Rect_Sleeve Sheet, page 34 Rect_Weld Sheet, page 37 Round_FlatFlange Sheet, page 26 Round_FlatFlangeVA Sheet, page 30 Round_Rivet Sheet, page 39 Round_Sleeve Sheet, page 32 Round_Weld Sheet, page 36 RoundElbow Sheet, page 60 SamplingTube Sheet, page 46 SurfMountIcover Sheet, page 48


58/79



HVACElbow Sheet

The HVACElbowsheet in the HVAC.xlsworkbook defines the elbows that you


PartNumber- Type the part number for the elbow. An example is HVACElbowFo.

PartDescription- Type a description for the elbow. An example is variable shape

and angle elbow.

SymbolDefinition- Type the symbol definition for the elbow.

ComponentType- Type the component type for the elbow.

DryWeight- Type the empty weight of the elbow. You must specify the type of units

when you enter this value.

WaterWeight- Type the water weight of the elbow. You must specify the type ofunits when you enter this value.

DryCogX- Type the center-of-gravity location for the elbow along the X-axis when

the elbow is empty

hvac reference data guide

Documents