Mech PlusAutomationware
Automationware Mech Plus,the technological alternatives to pneumatic cylindersand/or hydraulic cylinders, without compromises.
2005 Automationware has commenced with greater determination a continuous research in development ofelectric cylinders with high mechanical performance.
The new Mech Plus series satisfies today the demanding requirements, to offer the best tradeoff between price and performance.
With innovative technologies and high production care,the products stand out for the unique performance of the high axial force on essential structural dimensions,for greater reliability and duration.
Realized in 6 sizes: 50, 63, 80, 100, 125 and 160, they use recirculating ball screws powered by line or parallel transmission with Anti-Rotation System, in fulfillment of ISO 15552 (with mounting terminals).
The ideal solution forheavy workloadswith electric drive and intelligent control
Story of acontinual innovation
50 63 80100 125 160
Mech PlusAutomationware
2 www.automationware.it
The range includes a valid alternative to pneumatic cylinders and ensures a significant reduction of the costs, improvement of productivity and project cycles simplification.
Automationware proposes its motorisation to obtain the essential dimensioning, and guarantees to the customer the choice to use different types of motors and electronic controls.
The available motors are Brushless or Stepper With closed loop control.
Under the Easy Insert application, in the function of the cylinder as press.
This graph shows the force exerted on the actuator according to its position.
The three force verification windows are also shown in different colours, depending on the result of the verification.
• Not only the productivity increases, the accuracy refines and the movement modulates
• It is less subject to temperature variations or to pressure variations of the pneumatic and hydraulic systems
• Eliminates the extra cost for the pneumatic or hydraulic cylinder management
• Makes it easier to service, ecologic, doesn’t requires the calibration of the valves
• It can be controlled directly via EtherCat and has a remote diagnostic service, also controllable from any Web. (version with electronic control)
• High performances over 150 kN (190 kN with Mech Force), combined with compactness and low energy consumption
• Complete control of the cylinder with position, speed and applied force verification
• Axial speed up to 1m/sec
• Simplified maintenance, centralized lubrication and IP65 protection
• Anti-Rotation System, low noise and high productivity
• Easy programming with the Automationware EASY™ application
• AwareVu™, for the Ind. 4.0 diagnostics, also available provided with Wi-FI connection for the detection of minor service anomalies, determined by unusual vibrations.
Benefits
Key Features
AwareVu™The cylinder offers as an option the electric AwareVu monitoring system, that allows the vibration and temperature diagnosis, connectable to WI-FI and programmable by tablet or smartphone.
Also available the control Package with configuration software for the application (EASY™).
Furthermore it is available with rod and inox-steel elements for use in humid applications.
3www.automationware.it
Packagingand/or material motionVery useful for packaging systems, ideal solution for industrial applications, such as the logistics, if the material movement needs high forces, modulate movements, also with high speed.
Applications
Automotive and heavy load movingThe automotive industry sector often requires the use of hydraulic cylinders for the production chain and for the components-assembly phase (Use of the cylinders as press.) The easy installation and the easy programming, makes them very useful to avoid complex pneumatic or hydraulic installations.
Diagnosticand HealthcareThe electric cylinder can be very useful for micrometric movements on scanning devices and TAC. The system also maintains the position, even without power supply. In absence of the hydraulic, it is the ideal solution to simplify the design of the compact and transportable medical diagnostic systems.It allows the accurate positioning of persons and objects for the electronically programmable diagnostics.For the pharmacological production cycles, the electric cylinders prevent each contamination,allow the product packaging in aseptic rooms with precision and minimal maintenance.Automationware provides also linear axes, combinable with other Pick & Place solutions for the packaging of pharmacological products for automated diagnostic.
Aerospace & DefenceMany defence applications need industrial actuators to moderate the investment,maintaining an excellent level of quality and easy use in normal application situations.Our cylinders offer a very good applicability for different configurations, such as navigation simulators (also militar). Very useful also for the logistic applications, if the IP65 protection can be appropriate.
4 www.automationware.it
Factory automationEssential in modern palletising systems, excellent in industrial production chainsto find a rapid solution to eventual line problems. Very useful for the warehouses, as extending and upgrading of existing facilities.
EnergyWidely used for the flow control of the hydroelectric turbines, for easy installation and regulability. Widely used also for wind-power applications, forthe variation of the incidence angle of the blades. Very useful also for fuel extraction or fuel production installations, thanks to its easy maintenance and management, also by remote control.
Machine toolsUsed as substitutes for hydraulic systems of machines for metal sheets bending.The easy use and the simplification of systems make them very popular in the applications that need the “press” type operation.They can also be used in very vertical applications, such as tyre-inserting machines, simplifying the hydraulic inserting systems.Machine tools for the production of springs or for the mechanical component insertion, such as bearings, bushings, ringnuts, reducing the complexity of the systems, modulating the pressure with programmed motion.
ModelsCharacteristic / Models
UM Mech Plus 50
Mech Plus 63
Mech Plus80
Mech Plus 100
Mech Plus 125
Mech Plus 160
Mech Plus 160
Dimensions flanges mm F. 65 F. 75 F. 100 F. 120 F. 140 F. 180 F. 180
Screw diameter and lead
mm 25P10 32P10 40P10 50P10 63P10 80P10 80P20
Max Torque Motor Nm from 1,2 to 2,2
from 1,8 to 4,4
from 3 to 9,6
from 6,1 to 14
from 10,9 to 22,5
from 14,6 to 45
from 24 to 45
Reduction Ratio i 1 / 3 / 4 / 5 / 7 / 10 / 16 / 20
Gearbox ratio PG according to above
Max torque gearbox output (Cm )
Nm from2,2 to 24,3
from4,4 to 36,4
from9,6 to 60,7
from 14,0 to 121,4
from22 to 218,4
from45 to 291
from45 to 485
Max torque screw input (Cin max)
Nm from2 to 19,7
from4 to 29,5
from7,78 to 49,1
from 11,34 to
98,3
from 17,82 to
177
from108 to
236
from110 to
393
Max axial in line force Cin max
N from 1,1k to
10k
from 2,3k to
15k
from5,4k to
25k
from7,8k to
50k
from 12,3k to
90k
from25k to 120k
from 12,6k to
100k
Max Motor speed rpm 4500 4375 3500 2800 2222 1750 1750
Max screw speed rpm from 4500 to
225
from 4375 to
225
from 3500 to
225
from 2800 to
225
from 2222 to
200
from 1750 to
150
from 1750 to
150
Max axial speed mm/sec from 750 to
38
from 729 to
38
from538 to
38
from467 to
38
from370 to
33
from292 to
25
from583 to
50
Available Stroke mm from50 to 600
from50 to 800
from50 to 900
from 50 to 1100
from50 to 1300
from50 to 1500
from50 to 1500
5www.automationware.it
with self-lubrication for lower degradation
Head bearing
Seal to avoid contamination from external and selected for severe temperature variation (degree of protection IP 65) – Double protection for hostile situation
Dust scraper
Inserted on chassis (no external wires)
Magnetic detectors
Mech PlusAutomationwareDesigned to offerthe best combination of force performancewith a compact and solid form factor
With very high efficiency using a best performance helicoidal planetary system for long life and low noise level (Backlash ≤ 5)
Gearbox
to prevent vibrations in high speed
GGB bearings
system included on the roller screw ball system for accurate positioning optimization
Permanent Magnetic
6
With factory pre-setup for best efficiency and accuracy
MicrometricBelt tension system
belt for high durability stiffness
High performance Kevlar
Cylinder with anti-rotationsystems included
Anti-Rotation systems
Tapered roller bearings, with high capacity torque and pin for centralized lubrication system
Lubrication system
Optional lateral pins for heavy loads operations
Lateral pins
(ISO 5 optional), for long life spam and heavy load
Roller balls screw ISO 7
7
Axia
l For
ce k
N
Nominal lifetime - km
0
5
10
15
20
25
30
100 1000 10000
MechPlus 5025x10
MechPlus 6332x10
MechPlus 8040x10
Axia
l For
ce k
N
Nominal lifetime - km
0
20
40
60
80
100
120
30 300 3000
MechPlus 10050x10
MechPlus 12563x10
MechPlus 16080x10
MechPlus 16080x20
Service lifetimeNominal cylinder lifetime in KmMechPlus 50, MechPlus 63 e MechPlus 80relative to the applied axial force.
Service lifetimeNominal cylinder lifetime in kmMechPlus 100, MechPlus 125 e MechPlus 160relative to the applied axial force.
Specifications
8 www.automationware.it
Comparison between actuatorsFor each component of the MechPlus family is indicated the maximum axial force and the maximal axial force that guarantees a lifetime of 2500 km.
Max axial in line force Cin max (N)Max Force applicable for duration of 2500 km (N)
20000 40000 60000 80000 100000 120000 140000 160000
Indication Table of estimated duration based on 2500 km
Mech Plus 50
Mech Plus 63
Mech Plus 80
Mech Plus 100
Mech Plus 125
Mech Plus 160(Lead 10)
Mech Plus 160(Lead 20)
0
Axia
l For
ce k
N
Nominal lifetime - km
0
5
10
15
20
25
30
100 1000 10000
MechPlus 5025x10
MechPlus 6332x10
MechPlus 8040x10
Axia
l For
ce k
N
Nominal lifetime - km
0
20
40
60
80
100
120
30 300 3000
MechPlus 10050x10
MechPlus 12563x10
MechPlus 16080x10
MechPlus 16080x20
Service lifetimeNominal cylinder lifetime in KmMechPlus 50, MechPlus 63 e MechPlus 80relative to the applied axial force.
Service lifetimeNominal cylinder lifetime in kmMechPlus 100, MechPlus 125 e MechPlus 160relative to the applied axial force.
Specs / Models UMMech
Plus 50Mech
Plus 63Mech
Plus 80Mech
Plus 100Mech
Plus 125Mech
Plus 160Mech
Plus 160
Diameter / Lead mm 25P10 32P10 40P10 50P10 63P10 80-P10 80-P20
Max Axial Force kN 10 15 25 50 90 120 150
Average Force at 2500 km kN 3,15 5,36 12,4 15,5 17,4 19,3 33,8
9www.automationware.it
3
4
1
11
9
102
5
6
7
8
Mech PlusAutomationware
ACCESSORIES MECH PLUS
POSITION DESCRIPTION
1 Direct Drive Kit
2 Parallel Drive Kit
3 Lateral Pins Kit
4 Lateral Flange Support For Pins Kit
5 Female Threaded
6 Spherical Rod End
7 Clevis Rod End
8 Fork Rod End
9 90°Backward Joint Swinging Kit
10 Backward Joint Swinging Kit
11 Hall Sensor
Accessories
10 www.automationware.it
SUMMARY OF DIMENSION: for basic in line and parallel version
Cylinder size UM PLUS 050 PLUS 063 PLUS 080 PLUS 100 PLUS 125 PLUS 160Screw lead mm P10 P10 P10 P10 P10 P10 P20
A1 17 20 23 28,5 30,5 45 45A2 17 20 23 28,5 30,5 45 45A3 27 30 41 55,5 50,5 60 60A4 27 30 39 47,5 50,5 60 60A5 24 34 40 50 70 80 80ØB 50 g6 70 g6 80 g6 100 g6 120 g6 160g6 160g6
ØB1 50 g6 63 g6 80 g6 100 g6 125 g6 160g6 160g6D 46,5 56,5 72 89 110 140 140
ØD 45 58 71 88,8 112 140 140E1 M8x18 M8x18 M10x20 M10x20 M12x20 M16x30 M16x30E2 M8x10 M8x10 M12x12 M16x20 M16x20 M20x30 M20x30E3 N°6 M4x12 N°8 M4x12 N°8 M4x12 N°8 M5x12 N°4 M10x20 N°8 M10x20 N°8 M10x20F 3 3 5 6 6 10 10
F1 3 6 6 6 6 13 13ØG 14 h7 16 h7 22 h7 25 h7 32 h7 35 h7 35 h7G1 22 25 28 38 45 46 46H 5 5 6 8 10 10 10
H1 16 20 20 36 40 40 40ØI 40 55 65 80 90 120 120
ØI1 28 38 44 56 75 85 85L 132 137 178 216 219,5 270 325
L1 176 187 240 292 300,5 375 430L2 56 60 70 76 90 118 118L3 36,5 46,5 49 63 69 80 80M M20x1,5 M20x1,5 M27x2 M27x2 M33x2 M42X2 M42X2
M1 35 40 45 45 60 80 80N 65 75 100 120 140 180 180P 157 204,5 243 283,7 302 356 363,5
P1 189 225,5 231 311,5 239,5 390,5 398R 43 58 58 70 78 107 107
R1 65 75 100 120 139 180 180R2 150 190 227 305 320 415 415R3 110 152 177 211 212 264 264R4 142 168 165 238,5 328,5 298,5 298,5
C*= Cylinder Stroke
Components
MØI
ØB
A1 A2L+(C*)
L1+(C*)
A3 A4F F1
L3
ØG
H
ØI1
ØB1
A5DN
ND
A5D
D
L2
G1
ØD
E3
H1
E2 E2
R
R3
R1
R2
M1
PP1
N
N
R4
E1 E1
11www.automationware.it
Mech LineAutomationwareOther actuators of the Mech Line series
Mech Line (Base) Electric Cylinders
ISO 15552 compatible
Realized in 4 sizes 25 (new), 32, 50 and 63.
With recirculating ball screw powered byline or parallel transmission.
Perfectly compatible with pneumatic cylinders.
Series Anti-Rotation System.
The available motors are Stepper or Brushless with closed loop control.
The cylinder can be controlled with the Easy Software,with the same modes of the Plus series.
The MechLine series offers a valid alternative to pneumatic cylinders, with low costs and the benefits of a complete adjustability of positioning and acceleration.
Specifications M.U. Mech Line 25 Mech Line 32 Mech Line 50 Mech Line 63
Diameter flange mm Flangia 32 Flangia 47 Flangia 65 Flangia 75Diameter screw mm 10 12 16 20Lead Screw mm 3-10 5-10 5-10-16 5-10-20Max Axial Force CIN N 2800-2500 5140 - 3900 10490 - 11810 - 8330 14600 - 11000 - 13400Average Force x 2500 km N 298 - 398 649-620 1324 - 1878 - 1549 1843 - 1749 - 2684Stroke window mm 300 500 500 600
12 www.automationware.it
Mech ForceAutomationwareOther actuators of the Mech Force series
Mech Force Electric Cylinders
ISO 15552 compatiblefor forces up to 190kN
Realized in 6 sizes 50, 63, 80, 100, 125 and 150.
With recirculating ball screw powered by line or parallel transmission.
Series Anti-Rotation System.
Aluminium profile structure, except for the 150,with steel structure for heavy loads.
Interface to the motor of the customer or of Automationware.
The available motors are Stepper or Brushless with closed loop control.
Available also as complete Package ready for use with Easy application software configuration.
Available also the version with rod and steel elementsfor food processing environments.
Specifications M.U. Mech Force 50 Mech Force 63 Mech Force 80 Mech Force 100 Mech Force 125 Mech Force 150
Diameter flange mm Flangia 65 Flangia 75 Flangia 95 Flangia 115 Flangia 125 Flangia 165
Diameter screw mm 20 25 32 40 50 63Lead Screw mm 5-10-20 5-10-25 5-10-20-32 5-10--20-40 5-10-40 10-16-20Max Axial Force CIN kN 14,6-11-13,4 19,8-16-15,1 25,9-29,8-22,7-
24,123,9-60,4-48,9-
44,430,9-76,9-51 87,9-190-141,9
Average Force x 2500 km kN 1,8-1,7-2,6 2,5-2,54-3,25 3,27-4,74-4,54-5,64
3-9,6-9,8-11,2 3,9-12,2-12,9 13,9-35,6-28,4
Stroke window mm 300 600 800 1000 1000 1000
13www.automationware.it
Mech LineAutomationware
ACCESSORIES MECH LINE/FORCE
Position Descriptions
1 Direct Drive Kit
2 Parallel Drive Kit
3 Lateral Pins Kit
4 Joint Swinging Kit
5 Lateral Flange Support For Pins Kit
6 Lateral Flange Support For Pins Kit
7 Lateral Flange Support For Pins Kit
8 Clevis Rod End
9 Fork Rod End
10 Joint Swinging Kit
11 Hall Sensor
Accessories
2
1
5
10
67
5
5
7
6
8
9
11
3
4
10
14 www.automationware.it
Components
L + (C*)L2
ØB
M M1
D
E
N
ØB1
ØG
L3
D
E
D
D
N
N N
Note: Present drawing is only an indication of Mech Line series.Please require always a 2-3D Layout or download the files from web site.(www.automationware.it)
DIMENSION: Base Version , Direct drive , Parallel Drive
Actuator Size UM Mech Force 50 Mech Force 63 Mech Force 80 Mech Force 100 Mech Force 125 Mech Force 150Lead screw mm 20x5-10-20 25x5-10-25 32x5-10-20-32 40x5-10-20-40 50x5-10-40 63x10-16-20
ØB mm 40 45 55 70 90 90ØB1 mm 50 63 80 100 125 150
D mm 46,5 56,5 72 89 Ø130 Ø130E mm N°4 M8x18 N°4 M8x18 N°4 M10x20 N°4 M10x20 N°8 M10x25 N°8 M16x30
ØG mm Ø12 h8 Ø14 h8 Ø17 h8 Ø24 h8 Ø32 h8 Ø32 h8L mm 173 182 228 285 300 438
L2 mm 45 55 60 70 105 95L3 mm 34 36,4 40 52,6 61 64M mm M16x1,5 M20x1,5 M20x1,5 M27x2 M30x2 M36x3
M1 mm 32 40 40 50 60 60N mm 65 75 95 115 135 165
Note: Present drawing is only an indication of Mech Line series. Please require always a 2-3D Layout or download the files from web site. (www.automationware.it)
C*=Cylinder Stroke
DIMENSION: Base Version , Direct drive , Parallel Drive
Actuator Size UM Mech 25 Mech 32 Mech 50 Mech 63Lead screw mm 12x5-10 12x5-10 16x5-10-16 20x5-10-20
ØB mm - 30 40 45ØB1 mm 22 30 40 45
D mm Ø26 32,5 46,5 56,5E mm N°4 M3x5 N°4 M6x18 N°4 M8x15 N°4 M8x15
ØG mm Ø6 h8 Ø8 h8 Ø10 h8 Ø12 h8L mm 97,3 129 134 171
L2 mm 24 48 41 41L3 mm 20 25,5 27,6 36,5M mm M8 M10x1,25 M16x1,5 M16x1,5
M1 mm 20 20 32 32N mm 32 47 65 75
Note: Present drawing is only an indication of Mech Line series. Please require always a 2-3D Layout or download the files from web site. (www.automationware.it)
C*=Cylinder Stroke
15www.automationware.it
Mac
h P
lus
| 18.
10.2
016
EN
Automationware
Is a consolidated fact in the field of components and Automation systems. Founded in 2002, on the plant of Dolo (VE) designs, manufactures, and integrates Positioning solutions and linear or rotary motion solutions for the Factory Automation. It has know-how and leadership for mechatronic applications, thanks to the planning experience of the founders, with technological packaging systems (strong mechanical, electronical integration, control Firmware).
Other Automationware products© 2017 by Automationware - All Rights Reserved. The brochure contains indicative parameters, Automationware reserves the right to change these specifications. For a more profound consultation, we recommend to use the technical datasheet and/or visit our website www.automationware.it
All the material on this website is exclusive property of Automationware and/or of the represented companies, and they apply the Italian and European Copyright Laws; eventual texts from other sources are also protected by copyright and are property of their respective trademark owners. All these information and contents (texts, graphics and images) are reported to the best of our knowledge, public knowledge or copyrighted material, if unintentionally has been published in violation of the law, please inform us and we will immediately remove it. All trademarks are the property of their respective owners; third party brands, product names, company names, corporate names, company names mentioned may be the Trademarks of their respective owners or registered trademarks of other companies have been used solely for information purposes and to their owner’s advantage, without aiming at any copyright infringements.
Automationware s.r.l
Via Arino, 26A30031 Arino di Dolo, Venezia | Italia
Phone +39 041 51 02 028Telefax +39 041 51 02 187Internet www.automationware.ite.mail [email protected]
follow us on linkedIn
AW Linear Axis SystemAutomationware
Muoviamo le tue idee in ogni situazionecon velocità e accuratezza
Motion Line ML | HPC | HPCC | ProC | PlusCMotion Line HPV | ProV | PlusV