Download - Steps to Integrate a Site
Following steps should be followed during the Integration of BTS
1. Block Resource of the SITE and Set BTS auto load OFF.
SET BTSAUTOLD: BTSID=111, SWT=OFF;2. Take a sample cfg file of same type (Note the type of BTS (3606E/3606AE), No. of Carriers).do the changes if needed.
3. Change the following Items in this file:
a) Site ID (Take care that Site ID is in two parameters : btsid and localcellid so change in both.
b) BCIM IP in
cbtsbcimip:btsid=610,brdid=0,brdip="10.180.82.37",brdsnm="255.255.255.0", confirm=y;
by LST BTSLNK
c) BSC IP in
add cbtstersiglnk:btsid=610,ipver=ipv4,bscip="80.144.25.66",btsip="80.126.2.98", btssnm="255.0.0.0",brdid=0,abislnktp=cdma1xonly,bearertp=ip,peerip="10.180.32.2"
by LST SUBSYSTEMd) BTSIP in
add cbtstersiglnk:btsid=610,ipver=ipv4,bscip="80.144.25.66",btsip="80.126.2.98", btssnm="255.0.0.0",brdid=0,abislnktp=cdma1xonly,bearertp=ip,peerip="10.180.32.2"
by LST BTSLNKe) PEERIP (PEUBa IP) inadd cbtstersiglnk:btsid=610,ipver=ipv4,bscip="80.144.25.66",btsip="80.126.2.98", btssnm="255.0.0.0",brdid=0,abislnktp=cdma1xonly,bearertp=ip,peerip="10.180.32.2"
by LST IP
f) Check the Max cell radius and change if needed. For most of the BTS it is 31.4. Run the batch File.
5. Save file - SAV CBTSCFG6. Download Software
DLD CBTSALLSW: BTSID=710, LDTP=DLDACT, LDOPTION=ALL;
(During downloading specially note the downloading of following software:1. FPGA software of CMTR.
2. FPGA software of CCPM.
3. CPU software of CCPM.
4. cfg file. )
7. If any activation failed than download software again but only Different Load optionDLD CBTSALLSW: BTSID=710, LDTP=DLDACT, LDOPTION=DIFF;
8. Save file again. SAV CBTSCFG9. Load Software version of Stand By BCKM:
BKP CBTSFILE: BTSID=111, OBJTP=BCKM, SWTP=CPUFollowing Steps are for checking the Status:
1. Check the Software version BTS Boards.
GET CBTSBRDVER: BTSID=111;
The result should be like the below:
Board Version Information------------------------
BoardType BoardID Software Version Logic Version Remark
BCKM 0 V300R002C01B022CP0006 (U5)018
BCKM 1 V300R002C01B022CP0006 (U5)018
BCIM 0 V300R002C01B022CP0006 (U74)003(U17)019
CRDM 0 V300R002C01B022CP0005 (U30)003(U37)005(U54)004
CCPM 0 V300R002C01B022CP0006 (U26)002(U51)003
CCPM 1 V300R002C01B022CP0006 (U26)002(U51)003
TRM 1 V300R002C01B022CP0006 (U5002)003(U6500)132(U7001)129
TRM 3 V300R002C01B022CP0006 (U5002)003(U6500)132(U7001)129
TRM 5 V300R002C01B022CP0006 (U5002)003(U6500)132(U7001)129
If there is some problem like different Software Version then Download Software again. 2. Check the validity of different types of Software of BTS Cards
DSP CBTSSW: BTSID=111;
The result should be like this:Query Result
------------
Software Type
File Name
Software Status File Length(byte)Download
Time
BCKM CPU SoftwareBCKM3606.BZP
Currently valid 20736492008-06-20 06:50
BTS Configuration Data CBTSCFG.BIN
Currently valid 5504 2008-06-26 01:05
CMTR CPU Software CMTR.BZP
Currently valid 1173855 2008-06-20 06:30
QC54BCIM CPU Software CIM_8270.BZP
Currently valid 1764514 2008-06-20 06:46
QC54BCIM FPGA SoftwareQC54BCIM_FPGA.BZP Currently valid 254097 2008-06-20 06:43
CMTR FPGA Software QCK1MTRX_FPGA.BZP Currently valid 1390838 2008-06-20 06:24
CCPM FPGA Software QCK3CCPM_FPGA.BZP Currently valid 392134 2008-06-20 06:39
CCPM CPU Software QCK3CCPM.BZP Currently valid 1306321 2008-06-20 06:41
CRDM FPGA Software CRDM_FPGA.BZP Currently valid 756825 2008-06-20 06:35
CRDM CPU Software CRDM.BZP
Currently valid 407647 2008-06-20 06:37
(Number of results = 10)
--- END
Total Software should be 10 and Status of all must be Currently valid If any software is missing download that specific Software by using:
DLD CBTSSW:
** This command only downloads the Software but will not activate. You have to activate the software manually.
For this go to Equipment Panel >> Master Rackand Right Click the Specific board and Activate the Specific software manually.3. Check the GPS DSP CBTSBRDSPECSTAT: BTSID=111, BRDTP=BCKM, BRDID=0, MTRLGY=MET;
DSP CBTSBRDSPECSTAT: BTSID=111, BRDTP=BCKM, BRDID=1, MTRLGY=MET;
Execution Result
----------------
BTS Name = Chowk
BTS ID = 111
Board Type = BCKM
Board ID = 1
Reference Clock Source = Clock Reference in Board
Receiver Module Model = Resolution-T
Receiver Module Mode = GPS
GPS Satellites Traced = 10
GLONASS Satellites Traced = 0
Latitude = North 26 degrees 46 minutes 47 seconds 437 milliseconds
Longitude = East 82 degrees 9 minutes 1 seconds 946 milliseconds
Altitude = 90.00 m
Status of Software PLL = Locked
Current UTC Leap Second = 14
Time System = Standard Time
GPS Satellite Traced should be at least 4. If less than 4 rectify it.
4. Check BER
DSP CBTSLNKSTAT: BTSID=111, BRDID=0;
DSP ERRCODERATIO: FN=2, SN=24, LNKNO=0;
5. Check Time Zone
LST SYSMSGPARA: CN=111, CCMINF=SCHM;
Time zone should be +5:30.
Otherwise change by: MOD SCHM: SUBITEM=CRR_CLASS, CN=112, LOCTMOFF=LF43;
6. After all these steps Run the RF Script for this site and Set BTSAUTOLOAD On by:
SET BTSAUTOLD: BTSID=111, SWT=ON;