Version June 2013

AgGPS 252 receiver

NH 252 receiver

AFS252 receiver

AgGPS 262 receiver

NH 262 receiver

AFS262 receiver

AgGPS 372 receiver

NH 372 receiver

AFS 372 receiver

AgGPS 162 receiver

NH 162 receiver

AFS162 receiver

Appearance

Software version

bf_370.img

AgGPS262_5_01_001_4.img

(Software includes improvements for VRS

and OmniStar performance – helps to

reduce dropouts)

- RTK Age threshold increased from 40

seconds to 60 seconds

- xFill is NOT supported on 262

Ag372_2_01_002_4.img

(Software includes improvements for

VRS performance – helps to reduce

dropouts)

- xFill will be supported in the next

version of the 372

ahi_1_01_000_4_162.img

The version below is available but only corrects a small bug:

ahi_2_17_004_4.img

Software

Download Tool

Flashloader 200 (V3.34 or higher)

Configuration

GPS Remote software or by screen of your application (EZ-guide plus, EZ-guide 500, SWCD,CODI,FRED)

Configure AORE(120) or IORW(126) to heed health and all the rest to disabled

For OmniStar configure the receiver to “ESAT”. On some receivers it may be necessary to configure the satellite frequency manually (1539.9125 MHz/Baud Rate: 1200bps) (Europe Only).

For RTX CentrePoint (Sat) configure the receiver to 1539.9525 MHz and baud rate 600bps. This configuration should be done in RTK Config menu & NOT the DGPS Config menu in the RDI

screen (Europe Only).

EST availability

(V7.6.0.0)

Firmware version : Yes

Download/ConfigTool:Yes “Intellisteer/Accuguide Autoguidance System II / Precision Farming / GPS” – Additional tools

Cable / Tool

380002422 or

87298129/73316783/ZTN50166 is the big one (7 meter) Or alternatively: ZTN68463 (data output cable 262/162)

(To be able to use the 162 receiver for

autoguidance (Egnos), you will need to

unlock the 162)

EZ-guide 500 screen EZ-guide 250 screen FM750 FM1000

Appearance

Software version Ezg500_5_10_038_4.img

Languages: *.lpf

ezg250_3_10_038_4.img

Languages: *.lpf

cfx750_4_05_009_4.img

Languages: *.lpf

V4.00 - xFill, RTX RangePoint & FIQ Boom Height

Control System are supported.

V4.01- corrects a bug for EZ-Pilot and EZ-Steer

systems that was introduced in V4.00.

No language files for V4.01.

V4.05 - corrects a bug that caused RTK

frequencies to be lost.

- also corrects an issue that prevented

the APN settings being adjusted

through the display

First install monitor v. 1.17

"cfx750_mon_1_17.mnc" if FM750 is <V1.90

v7.20_FmX_Integrated_Display_Firmware.upg

V6.63 - Resolves an issue with Yield Monitoring calculation

V7.00 - Includes VRS improvements to help reduce dropouts

- Includes further corrections for Yield Monitoring

- Corrects an issue that caused RTX unlocks to be

deleted during system restore

V7.10 - AP Vehicle database updated to V4.3

- Additional ISO TC functionality introduced

V7.20 - Support for xFill & RTX RangePoint

(see the release notes on the Trimble Support Page for more

detail on new features and improvements)

Software Download

Tool

Copy to USB

Configuration

Through display

Through display

Through display

Password: 2009

EST availability

(v7.6.0.0) Firmware version: EST + ASIST>>>Trimble Support Page Firmware version & Language Files (FM750): ASIST>>>Trimble Support Page

Cable / Tool

USB Device: Lexar firefly 1GB (P/N ZTN64268-00)

062/Garmin antenna NH/AFS 100/110/134 EZ-guide plus screen Field Manager display

Appearance

Software version No Software Available

NH/AFS100 : CF_306.tnr

NH/AFS110 : SS_306.tnr

NH/AFS134 : BT_306.tnr

EZGPlus4.11.004-EU6.ROM v5.20 (Upgrade, autorun, cougar)

Software

Download Tool

[No Software Available]

Flashloader 100

EZ-Toolbox software

Copy to Compact Flash Card

( Copy the upgrade folder and

autorun/cougar-files)

Configuration

SNSRCFG_320.exe

- Ensure baud rate is configured to 38400bps

- NMEA 2.30 mode is set to ON

- FIX + DGPS + DIFF mode is set to AUTO

- Only NMEA sentences “GPGGA, GPGSA,

GPVTG, GPGSV” should be selected for good

communication with the display

GPSRemote software or

by screen of your application

(EZ-guide plus, EZ-guide 500, SWCD,CODI)

Configure AORE(120) or IORW(126) to heed

health and all the rest to disabled

Through display

Through display

Password: 2005

EST availability

(v7.0)

Firmware version : No

Download/ConfigTool:Yes

“Intellisteer/Accuguide Autoguidance System II

/ Precision Farming / GPS” – Additional tools

Firmware version : Yes

Download/ConfigTool:Yes

“Intellisteer/Accuguide Autoguidance System II /

Precision Farming / GPS” – Additional tools

Firmware version : Yes

Download/ConfigTool:Yes

“EZ guide plus lightbar guidance system” –

Additional tools

Firmware version:

ASIST>>>Trimble Support Page

Cable / Tool

380002422 AND 380003304

277885A1 OR 87418417

Null modem cable

ZTN59043 OR 87297613 (in kit)

CF Card+adapter: P/N : 84396507

Intellisteer/Accuguide Trimble autopilot EZ-steer EZ-steer 500

EZ500 EZ250 FM750

FM1000

EZ-Pilot

Appearance

Software

version Display AutoGuidance SW CNH NAV SW

v12.x ceres_cnh_v_3_27.img

v16.4 ceres_cnh_v_3_35.img

V25.6 3.57 (3.72)

V26.5 3.65 (3.72)

V27.2 3.72

V27.3-4 3.75 (New steering Cal logic for CCH)

V27.5 3.78

V28.1 3.80 (sudden XTE jump fix)

V28.2 3.82

V28.4 (lang28.5) 3.85 (AG715 RTK Radio Channel Fix)

Receiver/Display

SW

Trimble NAV SW

EZ-Guide Plus

EZ500 (V3-3.06) v.4.52

EZ500 (V5.10)

FM1000 (V4.00)

FM750 (<V1.90)

262 (V2.00)

252 (V3.70)

V5.15/V5.16

FM1000 (V7.2)

FM750 (>V4.01)

V5.26

VDB4.3

V5.26

VDB4.3

SCM_3_0_1.app SCM_4_1_0.app No Software Available

Software

Download

Tool

FlashLoader 200

EZ-Toolbox software

N/A

Configuration

Through display

Through display

Through display

EST

availability

(v7.6.0.0)

CNH NAV Software version : Yes (3.03, 3.27, 3.57, 3.65, 3.78, 3.80, 3.85)

Download/ConfigTool:Yes

Trimble NAV Firmware version and VDB-

list 4.3: ASIST>>>Trimble Support Page

Firmware version : Yes

Download/ConfigTool:Yes

“EZ guide plus lightbar guidance system” –

Additional tools

N/A

Cable / Tool

To support all ages of IS/AG vehicles it will be necessary to order each of

the three cables above.

Is also possible without cable

Serial cable e.g. from EST box

Note: For CNH Hybrid Installations the cables in the cell to the left will be required for software

download to the Trimble Autopilot Controller

N/A 380002422

Serial cable e.g. from

EST box 380001593

Intellisteer/AccuGuide:

For more configurations: use Autopilot

Toolbox II

“Trimble Brand Autoguidance

systems”Additional tools

FM750 / EZ500 / EZ+ use EST:

Autopilot Toolbox

“Trimble Brand Autoguidance

systems” – Additional tools

FMD + FM1000: in display config

- If installing V3.82 or higher on a CCH tier 4

tractor with a class 5 axle ensure the UCM

software is updated to V1.07.00.00 or

higher to ensure the NAV controller uses

the correct steering pot slope.

- Software bug with V28.4 AG language files

so use V28.5 AG language files. Update

patches are on the EST Support page.

When updating the NAV to V5.25 or

V5.26 ensure the following process is

followed:

1. Load default vehicle with AP Toolbox

2. Upgrade the NAVII firmware

3. Choose a profile from VDB list V4.3

4. Recalibrate the system

AgGPS 450 Radio PDL 450 Radio TDL 450 Radio AG-715 Radio AgGPS RTK 450/442/542 Base

Appearance

Software

version

v1.30 AgGPS450_v130Upgrade.zfimg

v1.32 (required for (410-470MHz)

radio: 55560-45

AgGPS450_v132Upgrade.zfimg

v2.42

V3.04.2881

N/A

v3.67 (not for 542 base)

V4.60 (is valid for 542 base and for 450 base)

Software

Download

Tool Flashloader 200

or

Winflash software

(Select “Sitenet 450 Transceiver”)

(Press Ctrl+Insert to insert new software

if not available yet)

(for download set-files: use Winflash)

PDL Conf v.4

Choose generic CMR radio in EZ 500

when used as rover radio for EZ 500

(In EZ 500 for RTK security: choose

Trimble radio: configure secure code,

and then choose generic CMR radio)

TDL Conf V3.02

Set Files loaded with TDL

Conf Tool.

Configurations can be

done with TDL Conf or

using UI on the radio

No Software Download

Winflash

(Select “Trimble AgGPS Receiver”)

(for download set-files: use Winflash)

Winflash-tool 1.212 required to connect to 542-base.

Install: "WFC-AgGPS-V460.exe"

(Download from Asist > Autoguidance support (Tool)

Configuration

AgRemote software or by

using the RDI screen

Note: No set-file is required.

Frequencies are configured

in the AgRemote/RDI tool.

In some cases it may be

necessary to use the Ag

Remote tool to configure

the radio for the first time.

After this it is possible to use

the RDI screen.

EST

availability

(v7.6.0.0)

Firmware version : Yes

Download/ConfigTool: Yes

“Intellisteer/Accuguide Autoguidance

System II / Precision Farming / GPS” –

Additional tools

Firmware version : Yes

Download/ConfigTool: Yes

Firmware version : No

Download/ConfigTool:

ASIST>>>Trimble Support

Page

Firmware version : Yes

Download/ConfigTool: Yes

Firmware version : No

Download/ConfigTool:Yes/ Not in EST for 542

base

“Intellisteer Autoguidance System II / Precision

Farming / GPS” – Additional tools

Cable / Tool

Together with PDL 450 radio (=

power cable)

Together with TDL 450

radio (= power cable)

380002422

Nullmodem cable

ZTN59043 OR 87297613

(in kit)

Both tools required:

380002422 + 380002886

EZ-boom Field IQ/Yield Monitoring/Generic Rate Controller DCM-300 Modem

Appearance

Software

version TR_EZBOOM-1_5.fw2

Display MSB1

12 SSB2 RWCM

3 SIM

4 SCM

5 RSCM

6 SMM

7 MSM

8 YMM

9

FM1000 >V7.1 V3.05 V3.05 V3.05 V3.05 V3.05 V3.06 V2.05 V1.11 V1.15

FM750 >V1.9 V2.06 V2.06 V2.06 V2.07 V2.07 V2.14 N/A N/A N/A

>V4.0 V3.05 V3.05 V3.05 V3.05 V3.05 V3.05 V2.02 V1.11 V1.15

EZ500 V5.10 V1.02 V1.02 V1.02 N/A V1.04 N/A N/A N/A N/A

CNH GRC GRC V28.4 V3.06 V3.06 V3.06 V2.08 V3.06 V3.08 V2.06 N/A N/A

V4.00 (Recommend Minimum Version for VRS)

V5.01 (Recommended Minimum Version for

Telematics modem)

Install NAV V3.72 and V27.2 (AG+PF) as a

minimum when using DCM300 modem with

Intellisteer/AccuGuide

Software

Download

Tool

EZ500: EZ Boom - Copy to USB (root). (EZ500 will work with Field IQ (but not recommended). SW update is not possible. Use FM750/FM1000 for SW

Update.)

FM750 Copy to USB (root) – Not compatible with EZ-Boom

FM1000 Included in display main firmware - FM1000 v5 or higher NOT compatible with EZ-boom and TAC

EZguideplus: EZ-toolbox – Not compatible with Field IQ

FMD Copy to Flash Card under Firmware folder - Not compatible with Field IQ

CNH GRC Use EST – Planting & Seeding Equipment>>IntelliRate Control/AFS AccuControl System and Aftermarket ISOBUS Implements

Software Downloads are over-the-air (OTA)

Submit an ASIST report or contact local support

with modem serial number and request the

update.

A VRS modem can also be updated to V5.01 if

necessary; however on some modems the

Client IP address may need to be configured to

ensure the modem is connected to the correct

server for the OTA update.

Configuration

Through display:

Trimble WebService Tool

EST

availability

(V7.6.0.0)

Firmware version: For Trimble Field IQ: ASIST>>>Trimble Support Page

For CNH GRC: Ensure EST 7.6.0.0 Update 1 is installed on the EST laptop

Firmware: N/A

Configuration: Instructions for WebService

Tool in EST

Cable / Tool

For Trimble FIQ: USB Device (Lexar firefly 1GB (P/N ZTN64268-00)) For CNH GRC: EST Dearborn DPA5 Tool

Connect to the modem with WiFi laptop

Note1: The software filenames below are an example of the filename spelling and is not necessarily the latest/correct version for the controller in all cases.

Note2: Filenames for CNH Generic Rate Controller (GRC) will have the file extension .hx1

MSB1 – Master Switch Box – FIQ_12_Section_Switch_Module_2_06.ohr 12 SSB

2 – 12 Section Switch Box – FIQ_Master_Switch_Module_2_06.ofr

RWCM3 – Rawson Control Module – FIQ_Rate_and_Section_Control_Module_2_14.ohk SIM

4 – Switch Interface Module – FIQ_Rawson_Control_Module_2_06.orn

SCM5 – Section Control Module - FIQ_Section_Control_Module_2_07.omg RSCM

6 – Rate & Section Control Module - FIQ_Rate_and_Section_Control_Module_2_14.ohk

SMM7 – Seed Monitor Module - FIQ_Seed_Monitoring_Module_2_05.okn MSM

8 – Moisture Sensor Module - FIQ_Moisture_Sensor_Module_1_11.oms

YMM9 – Yield Monitoring Module - FIQ_Yield_Monitoring_Module_1_15.odu

FMD – EZ-Boom Only FM750 – Field IQ Only