version aggps 252 receiver aggps 262 receiver aggps 372 ... ......

Click here to load reader

Post on 21-Mar-2021

0 views

Category:

Documents

0 download

Embed Size (px)

TRANSCRIPT

  • Version June 2013

    AgGPS 252 receiver

    NH 252 receiver

    AFS252 receiver

    AgGPS 262 receiver

    NH 262 receiver

    AFS262 receiver

    AgGPS 372 receiver

    NH 372 receiver

    AFS 372 receiver

    AgGPS 162 receiver

    NH 162 receiver

    AFS162 receiver

    Appearance

    Software version

    bf_370.img

    AgGPS262_5_01_001_4.img

    (Software includes improvements for VRS

    and OmniStar performance – helps to

    reduce dropouts)

    - RTK Age threshold increased from 40

    seconds to 60 seconds

    - xFill is NOT supported on 262

    Ag372_2_01_002_4.img

    (Software includes improvements for

    VRS performance – helps to reduce

    dropouts)

    - xFill will be supported in the next

    version of the 372

    ahi_1_01_000_4_162.img

    The version below is available but only corrects a small bug:

    ahi_2_17_004_4.img

    Software

    Download Tool

    Flashloader 200 (V3.34 or higher)

    Configuration

    GPS Remote software or by screen of your application (EZ-guide plus, EZ-guide 500, SWCD,CODI,FRED)

    Configure AORE(120) or IORW(126) to heed health and all the rest to disabled

    For OmniStar configure the receiver to “ESAT”. On some receivers it may be necessary to configure the satellite frequency manually (1539.9125 MHz/Baud Rate: 1200bps) (Europe Only).

    For RTX CentrePoint (Sat) configure the receiver to 1539.9525 MHz and baud rate 600bps. This configuration should be done in RTK Config menu & NOT the DGPS Config menu in the RDI

    screen (Europe Only).

    EST availability

    (V7.6.0.0)

    Firmware version : Yes

    Download/ConfigTool:Yes “Intellisteer/Accuguide Autoguidance System II / Precision Farming / GPS” – Additional tools

    Cable / Tool

    380002422 or

    87298129/73316783/ZTN50166 is the big one (7 meter) Or alternatively: ZTN68463 (data output cable 262/162)

    (To be able to use the 162 receiver for

    autoguidance (Egnos), you will need to

    unlock the 162)

  • EZ-guide 500 screen EZ-guide 250 screen FM750 FM1000

    Appearance

    Software version Ezg500_5_10_038_4.img

    Languages: *.lpf

    ezg250_3_10_038_4.img

    Languages: *.lpf

    cfx750_4_05_009_4.img

    Languages: *.lpf

    V4.00 - xFill, RTX RangePoint & FIQ Boom Height

    Control System are supported.

    V4.01- corrects a bug for EZ-Pilot and EZ-Steer

    systems that was introduced in V4.00.

    No language files for V4.01.

    V4.05 - corrects a bug that caused RTK

    frequencies to be lost.

    - also corrects an issue that prevented

    the APN settings being adjusted

    through the display

    First install monitor v. 1.17

    "cfx750_mon_1_17.mnc" if FM750 is >>Trimble Support Page Firmware version & Language Files (FM750): ASIST>>>Trimble Support Page

    Cable / Tool

    USB Device: Lexar firefly 1GB (P/N ZTN64268-00)

  • 062/Garmin antenna NH/AFS 100/110/134 EZ-guide plus screen Field Manager display

    Appearance

    Software version No Software Available

    NH/AFS100 : CF_306.tnr

    NH/AFS110 : SS_306.tnr

    NH/AFS134 : BT_306.tnr

    EZGPlus4.11.004-EU6.ROM v5.20 (Upgrade, autorun, cougar)

    Software

    Download Tool

    [No Software Available]

    Flashloader 100

    EZ-Toolbox software

    Copy to Compact Flash Card

    ( Copy the upgrade folder and

    autorun/cougar-files)

    Configuration

    SNSRCFG_320.exe

    - Ensure baud rate is configured to 38400bps

    - NMEA 2.30 mode is set to ON

    - FIX + DGPS + DIFF mode is set to AUTO

    - Only NMEA sentences “GPGGA, GPGSA,

    GPVTG, GPGSV” should be selected for good

    communication with the display

    GPSRemote software or

    by screen of your application

    (EZ-guide plus, EZ-guide 500, SWCD,CODI)

    Configure AORE(120) or IORW(126) to heed

    health and all the rest to disabled

    Through display

    Through display

    Password: 2005

    EST availability

    (v7.0)

    Firmware version : No

    Download/ConfigTool:Yes

    “Intellisteer/Accuguide Autoguidance System II

    / Precision Farming / GPS” – Additional tools

    Firmware version : Yes

    Download/ConfigTool:Yes

    “Intellisteer/Accuguide Autoguidance System II /

    Precision Farming / GPS” – Additional tools

    Firmware version : Yes

    Download/ConfigTool:Yes

    “EZ guide plus lightbar guidance system” –

    Additional tools

    Firmware version:

    ASIST>>>Trimble Support Page

    Cable / Tool

    380002422 AND 380003304

    277885A1 OR 87418417

    Null modem cable

    ZTN59043 OR 87297613 (in kit)

    CF Card+adapter: P/N : 84396507

  • Intellisteer/Accuguide Trimble autopilot EZ-steer EZ-steer 500

    EZ500 EZ250 FM750

    FM1000

    EZ-Pilot

    Appearance

    Software

    version Display AutoGuidance SW CNH NAV SW

    v12.x ceres_cnh_v_3_27.img

    v16.4 ceres_cnh_v_3_35.img

    V25.6 3.57 (3.72)

    V26.5 3.65 (3.72)

    V27.2 3.72

    V27.3-4 3.75 (New steering Cal logic for CCH)

    V27.5 3.78

    V28.1 3.80 (sudden XTE jump fix)

    V28.2 3.82

    V28.4 (lang28.5) 3.85 (AG715 RTK Radio Channel Fix)

    Receiver/Display

    SW

    Trimble NAV SW

    EZ-Guide Plus

    EZ500 (V3-3.06) v.4.52

    EZ500 (V5.10)

    FM1000 (V4.00)

    FM750 (V4.01)

    V5.26

    VDB4.3

    V5.26

    VDB4.3

    SCM_3_0_1.app SCM_4_1_0.app No Software Available

    Software

    Download

    Tool

    FlashLoader 200

    EZ-Toolbox software

    N/A

    Configuration

    Through display

    Through display

    Through display

    EST

    availability

    (v7.6.0.0)

    CNH NAV Software version : Yes (3.03, 3.27, 3.57, 3.65, 3.78, 3.80, 3.85)

    Download/ConfigTool:Yes

    Trimble NAV Firmware version and VDB-

    list 4.3: ASIST>>>Trimble Support Page

    Firmware version : Yes

    Download/ConfigTool:Yes

    “EZ guide plus lightbar guidance system” –

    Additional tools

    N/A

    Cable / Tool

    To support all ages of IS/AG vehicles it will be necessary to order each of

    the three cables above.

    Is also possible without cable

    Serial cable e.g. from EST box

    Note: For CNH Hybrid Installations the cables in the cell to the left will be required for software

    download to the Trimble Autopilot Controller

    N/A 380002422

    Serial cable e.g. from

    EST box 380001593

    Intellisteer/AccuGuide:

    For more configurations: use Autopilot

    Toolbox II

    “Trimble Brand Autoguidance

    systems”Additional tools

    FM750 / EZ500 / EZ+ use EST:

    Autopilot Toolbox

    “Trimble Brand Autoguidance

    systems” – Additional tools

    FMD + FM1000: in display config

    - If installing V3.82 or higher on a CCH tier 4

    tractor with a class 5 axle ensure the UCM

    software is updated to V1.07.00.00 or

    higher to ensure the NAV controller uses

    the correct steering pot slope.

    - Software bug with V28.4 AG language files

    so use V28.5 AG language files. Update

    patches are on the EST Support page.

    When updating the NAV to V5.25 or

    V5.26 ensure the following process is

    followed:

    1. Load default vehicle with AP Toolbox

    2. Upgrade the NAVII firmware

    3. Choose a profile from VDB list V4.3

    4. Recalibrate the system

  • AgGPS 450 Radio PDL 450 Radio TDL 450 Radio AG-715 Radio AgGPS RTK 450/442/542 Base

    Appearance

    Software

    version

    v1.30 AgGPS450_v130Upgrade.zfimg

    v1.32 (required for (410-470MHz)

    radio: 55560-45

    AgGPS450_v132Upgrade.zfimg

    v2.42

    V3.04.2881

    N/A

    v3.67 (not for 542 base)

    V4.60 (is valid for 542 base and for 450 base)

    Software

    Download

    Tool Flashloader 200

    or

    Winflash software

    (Select “Sitenet 450 Transceiver”)

    (Press Ctrl+Insert to insert new software

    if not available yet)

    (for download set-files: use Winflash)

    PDL Conf v.4

    Choose generic CMR radio in EZ 500

    when used as rover radio for EZ 500

    (In EZ 500 for RTK security: choose

    Trimble radio: configure secure code,

    and then choose generic CMR radio)

    TDL Conf V3.02

    Set Files loaded with TDL

    Conf Tool.

    Configurations can be

    done with TDL Conf or

    using UI on the radio

    No Software Download

    Winflash

    (Select “Trimble AgGPS Receiver”)

    (for download set-files: use Winflash)

    Winflash-tool 1.212 required to connect to 542-base.

    Install: "WFC-AgGPS-V460.exe"

    (Download from Asist > Autoguidance support (Tool)

    Configuratio