VOLVO S60 XC60 Video Interface
For VOLVO S60 XC60 5inch monitor Main Features: 1. It is suitable for VOLVO 2011 up version 5 inch monitor 2. With 2AV input, RGBS input, Rear camera input, LVDS input 3. With 1AV output, LVDS output SYNCH 4. Built‐in CANBUS by original button NAV to Switch functions.
Auto Rear camera Activation completely when gear is in reverse position, no need to connect rear light +12V
5. With touch operation system for external DVD, DVB T, GPS NAVI. you can by touch screen to control DVD, DVB T, GPSBOX after by learing IR code command, this is excellent for add after‐market video unit.
6. With completely plug and play to finish the installation, no need to cut, and weld any cable to finish the installation
7. If you do not want to add the external touch screen in front of the original monitor, you can also use the original button on Radio to control the DVD, DVB T, or GPS by learing remote IR command code.
8. Built‐in GPS function (Optional) 9. Switch by original NAV button or by Toggle switcher. 10.
VOLVO S60 XC60 Video Interface VOLVO S60 XC60 Video GPS Interface
Connection: The Left Picture is car original CAN and Power cable Identify: 1. Blue/Orange cable: CAN- 2. White/Orange cable: CAN+ 3. Black cable: Ground 4. RED Cable: BATT
After finish installation, please to press the original button: and to Touch ICON LOGO when press or after control the touch Functions according to the montor touch ICON LOGO after Learning IR Code Command. by learnging the touch IR Code Command for after-market DVD, DVBT, TV, etc.
The functions switch: you can press the toggle switcher And also you can press the original button NAV to switch: To switch the fucnction. Radio RGB AV1 AV2 Radio RGB AV1 AV2 Radio RGB Radio RGBS
Touch Cable: FPC connector to touch panel, the other side to video interface Touch slot, as the abovr picture
If video interface without built-in GPS, then need to connect 4PINS to external GPSBOX Touch connector, 6PINS need to Connect GPSBOX RGBS output connector. But if Video Interface Built-in GPS, then both of these two connectot left empty, you can only connect one Touch cable with video interface, and touch panel is ok as the former picture show. Packing List: Daughter Board Power can CAN Cable Toggle Switcher RGB, AV, Touch cable Touch cable Speaker & GPS Antenna (only for built -in GPS Video Interface)
At present, BMW CIC, VOLVO, BENZ 2011 NTG4.5, AUDI 3G MMI, Benz S class, Ford viode interface, etc youcan only directly to connect this RGBS cable to be as the above instruction, then can realize external DVD, DVB T , GPS BOX by touch operation after by learning IR touch Code Command!
DVD, DVB T IR cable shielding case connecto to be Ground after cut the IR header.
IR cable connection:
Please look at the above picture, IR cable is for external DVD, DVB T IR cable input connection. In common, you need to cut the DVD, and DVB T IR remote cable IR receiver head, then you can
see there are three parts in this DVD IR cable: two small cable, and one is the shielding case.
Among the two small cable, the cable connecting to the first leg of IR head receiver is the IR signal transmittion, the other small cable is useless, so you only need to connect the IR transmitton
cable the video interface IR output cable together is ok. Please look at the right picture, the RED CIRCLE marked is the Fisrt Leg of IR header, to connect the DVD, or DVB T IR cable, and the Then to finish the video interface and external DVD, DVB T IR cable connection.
To set the video interface switcher 6th PIN to down for ready IR code learing as the picture:
Then the original screen will show the touch ICON for ready learning IR CODE COMMOND as the below picture:
Finally, to make the DVD, or DVB T remote contorller point at the video interface IR eye as the below picture show ( the IR eye is inside the video interface) to start the IR command learning
According to the monitor touch ICON LOGO to press the remote controller button
correspondly, you must do not exit this learning situation unit to finish the
all touch ICON IR command learning, otherwise, the learning will be failed. after finish
all the touch ICON learning then to pull up and down video interface switch 6th PINS
5-6 times to calibration, until the monitor appear the Cross LOGO, then stop to pull the
DIP6, and start to touch the CROSS LOGO to calibration touch functions. See the below
Pictures:
After calibration, you can touch the monitor
to operate the DVD, or DVB T by these touch ICON
Navigation System
Navigation
Refer to the manual of the third party navigation software for details.
Multimedia
Movie Player Click the “Movie” icon:
Operation Introductions:
2
Navigation System
Music Player Click the “Music” icon:
Operation Introductions:
3
Navigation System
Photo Brower Click the “Photo” icon:
Operation Introductions:
4
Navigation System
eBook Reader Click the “eBook” icon:
Operation Introductions:
5
Navigation System
Setup Submenu
Setup Submenu:
6
Navigation System
GPS Set Setup the path of the third party navigation software which is resident in the SD Card. After finish it, return to Main Menu, click the “Navi” icon, then the third party navigation software will be started.
If you hope that the third party navigation software will run immediately after system started, please check in the box.
Brightness
Click the “Brightness” icon:
7
Navigation System
Volume
Click the “Volume” icon:
Calibration
Click the “Calibration” icon:
8
Navigation System
Click the “Yes” button:
Usually
Click the “Usually” icon:
Screen Position Adjust
Click the “ScreenAdj” icon:
9
Navigation System
GPS Signal Monitor
Click the “G-Monitor” icon:
10
Navigation System
11
System Information
Click the “System” icon:
ISDBT Touch Operation when connect to our video interface:
When Switch to ISDVB T will show the Above MENU Then touch the monitor will show these Touch ICON
Then you can Operate the DVB T by these Touc ICON MENU selection and settings The relevant Ir touch Commad in our video interface for ISDB T as below list: 1 2 3 4 5 6 7 Logo
Functions TURN ON/OFF
Play /Pause Stop MENU MUTE Search EMPTY
LOGO
Functions Back to car
Radio CH + CH-
Volume- Volume+ Confirm
selection Return
____________________________________________________________________________________________4
1 Introduction
1.1 Features ■ DIP type of ISDB-T module ■ Frequency Range[Brazil:470~806MHz] [Japan:470MHz ~ 770MHz ] ■Size : 40(W) x 38(L) x 5.0(T) mm ■Analog AV output ■ UART / IR Remote Control Interface ■ Full Compliance with ISDB-T Standards ■ Lower Power consumption ■ High Sensitivity ■Voltage input:+ 3.3V,+1.8V
1.2 Applications
■ Personal Navigation Devices(NAVI/GPS) ■ Mobile TV, Car TV ■ PMP, PDA, MP3/4P ■ STB, Home TV Box ■ Portable and Handheld Devices with ISDB-T
1.3 Block Diagram
1.8V, 3.3V
RF
Full module Block Diagram
ISDBT NIM
Power Supply
Application
Processor
Flash MEM
DAC
SPI
I2C BUS
CCIR656
CVBS
I2S out
2CH Stereo out
IR/UART
____________________________________________________________________________________________7
2.2.2 : CON1,CON2: 1.27mm single socket(20pin)
Terminal No.
Terminal Name
Terminal Descriptions
1 +3.3VA +3.3V Power
2 +3.3VA +3.3V Power
3 GND Ground
4 +1.8VA +1.8V Power LDO POWER
5 +1.8VA +1.8V Power LDO POWER
6 GND Ground
7 E_RESETB External Reset
8 IR_IN Remoter Control Input
9 GND Ground
10 AOUT_R Analog Audio Right Out
11 AOUT_L Analog Audio Left Out
12 GND Ground
13 SCLK I2S
14 LRCK I2S
15 MCLK I2S
16 SDATA I2S
17 GND Ground
18 UART_RX Universal Asynchronous Receiver 19 UART_TX Universal Asynchronous Transmitter
Con1
20 GND Ground
1 GND Ground
2 CVBS_OUT Analog Video Out
3 GND Ground
4 I2C0_SDA Reserve
5 I2C0_SCL Reserve
6 GND Ground
7 NC 8 NC 9 GND Ground
10 V_CLK CCIR 656/601
11 GND Ground
12 YC656_0 CCIR 656/601
13 YC656_1 CCIR 656/601
14 YC656_2 CCIR 656/601
15 YC656_3 CCIR 656/601
16 YC656_4 CCIR 656/601
17 YC656_5 CCIR 656/601
18 YC656_6 CCIR 656/601
19 YC656_7 CCIR 656/601
Con2
20 GND Ground