drinking water systems - reverse osmosis, water ... files/undersink ro.pdf · reverse osmosis...

DrinkingWater

Systems

103

104 Hydrotech

The following chart on conditions for use is applicable to all the reverse osmosis systems listed.

The following pages of Hydrotech Reverse Osmosis Systems describe the two ways you can order.

A.Order by STANDARD Item Number which comes complete with Faucet and Storage Tank.

Complete system includes

• Reverse osmosis system manifold, with cartridges, membrane

and installation kit

• Chrome Faucet

• Metal storage tank

B.Order separate SYSTEM, FAUCET and STORAGE TANK by using the optional component pages

Reverse Osmosis Drinking Water Systems

+

Conditions for Use

+

Source Water Supply Profile Chemical Parameters Max mg/L

Notes: 1Pressure Regulator is recommended for feed water pressures exceeding 552 kPa (80 psig). The performance of a reverse osmosis

membrane is highly dependent upon pressure, temperature and TDS. The actual volume of product water and rejection percentage will vary

with differences from the test conditions that membrane ratings are based upon. These drinking water systems are not intended to be used

for the treatment of water that is microbiologically unsafe or of unknown quality. Storage tank capacity is dependent on pressure. Example:with a 5 psi precharge, the drawdown volume is 3.2 gal at 60 psi, 2.8 gal at 40 psi for the storage tank shown.

Smartap® U.S. patents: 5,145,575; 5,435,909; 5,580,444; 5,527,450

Community/Private Chlorinated/Non-Chlorinated Hardness (CaCO3) <350 (< 20 gpg)

Feed Water Pressure1 242 – 690 kPa (35-100 psig) Iron (Fe) <0.1

Temperature 4° – 38°C (40° – 100°F) Manganese (Mn) <0.05

pH Range 3.0 – 11.0 Hydrogen Sulfide (H2S) 0.00

Maximum TDS Level 2000 mg/L Residual Chlorine (Cl2) <2.0

Turbidity** <1.0 NTU **Nephelometric Turbidity Unit

Maximum SDI*** <4.0 ***Silt Density Index: Value stated in SDI units.

105Hydrotech

Reverse Osmosis Drinking Water Systems1240 Series Models and System Configurations

Order the systems listed above, which come complete with everything listed on this page.

* Manufacturer’s output specification only with inlet conditions of 372 kPa (60 psig), 25°C (77°F), going to atmosphere.**These models are tested and certified by WQA against NSF/ANSI 58 for the reduction of TDS. Tested and certified by WQA against ORD0902 for “lead free” compliance. WQA Tested and

Certified against CSA B483.1

PRO SERIESPremier Push Button Monitored

Reverse Osmosis Systems

Our premier model is equipped with our

patented Smartap® Push Button Monitor. At

the touch of a button you can be assured

that you are receiving top quality water or

you will be alerted that it is time to change

your membrane. This model also utilizes

three dedicated sediment and carbon filters.

All models include:

• High quality reverse osmosis membrane

• Choice of 9, 25, 50 and 75 gpd

• Sediment pre-filtration

• Pre & post carbon block filtration

• Quick connect fittings

• 3/8” tubing from RO to tank and faucet

for higher flow

• Color coded tubing for ease of

installation

• Air gap chrome faucet

• Storage tank

M SERIESHigh Quality Four-Stage Reverse

Osmosis Systems

This model produces great tasting

drinking water in the exact same fashion

as our Pro Series. The only difference

with this model is that it does not include

the patented Smartap® Push Button

Monitor.

All models include:

• High quality reverse osmosis

membrane

• Choice of 9, 25, 50 and 75 gpd




• 3/8” tubing from RO to tank and

faucet for higher flow


installation

• Air gap chrome faucet

• Storage tank

E SERIESCompact Three-Stage Reverse

Osmosis Systems

The E Series utilizes a combination

sediment and carbon pre-filter instead of

separate dedicated sediment and

carbon pre-filters. This system is great

for installing in tight spaces or for those

looking for the most economical

solution.

All models include:

• High quality reverse osmosis

membrane

• Choice of 25 and 50 gpd




• 3/8” tubing from RO to tank and

faucet for higher flow


installation

• Chrome faucet

• Storage tank

Hydrotech Model Sediment Output*Item # Description Vessels Filter Pre-Filter Membrane Post-Filter GPD Monitor

1240101-00 3VTFC25G 3 None Dual-Purpose Thin Film Composite Activated Carbon 25 None

1240102-00 3VTFC50G 3 None Dual-Purpose Thin Film Composite Activated Carbon 50 None

1240200-00 4VTFC09G 4 String Wound Polypropylene Activated Carbon Thin Film Composite Activated Carbon 9 None




1240300-00 4VTFC09G-PB** 4 String Wound Polypropylene Activated Carbon Thin Film Composite Activated Carbon 9 Push Button




All PRO SERIES models are tested andcertified by WQA against NSF/ANSI 58 forthe reduction of TDS. Tested and certifiedby WQA against ORD0902 for “lead free”compliance.

All PRO SERIES models are WQA Testedand Certified against CSA B483.1

106 Hydrotech

Three Vessel

Item # Model #

1240101-0 3VTFC25G

1240102-0 3VTFC50G

Four Vessel

Item # Model #

1240200-0 4VTFC9G

1240201-0 4VTFC25G

1240202-0 4VTFC50G

1240203-0 4VTFC75G

Four VesselPush Button Monitored

Item # Model #

1240300-0 4VTFC9G-PB

1240301-0 4VTFC25G-PB

1240302-0 4VTFC50G-PB

1240303-0 4VTFC75G-PB

Order basic RO manifold above with faucet and tank featured below.

Reverse Osmosis Drinking Water SystemsStandard Models with Optional Faucet and Storage Tanks

Air Gap Faucets

Item # Description

40301001 Chrome

87512 White

87515 Brass

87516 Almond

40301004 Stainless Steel

40302018 Satin

87520 Bisque

87518 Black

Non Air Gap Faucets

Item # Description

87513 Chrome

87514 White

87517 Brass

87519 Almond

87521 Brushed Nickel

87522 Polished Nickel

40301003 Stainless Steel

Non Air Gap Faucets

Item # Description

87511 Chrome Long Reach

Air Gap Faucets

Item # Description

92192 Chrome Long Reach

Standard Faucets QMP Faucets (Prop 65 Compliant)

Item Model

92313 3.8 Gallon ROPro Polypropylene

Tank w/ valve

42600029 PAE 4.0 Gallon Metal Tank w/ valve

9405 Structural Romate 15





Item Model

92324 Amtrol RO-2, 2 Gallon Tank




92325-1 Amtrol RO-20, 20 Gallon Tank



92323-1 Amtrol RO-86, 86 Gallon Tank

Storage Tanks

107Hydrotech

Economy RO Drinking Water SystemsAll models include: 3/8”outlet tubing for higher flows, thin film composite (TFC) membranes, quick connect

fittings for easy installation and servicing, heavy duty powder coated bracket, stainless steel product water check

valve, automatic shut-off valve, 4.0 U.S. gallon (15 litre) storage tank and under counter installation kit.

Economy RO Model ComponentsReverse Osmosis Membrane - allows water molecules to pass while dissolved impurities are flushed to the drain.

Five Micron Pre-Filter - removes tiny particles of suspended dirt and sediment.

Activated Carbon Pre-Filter - protects TFC membrane from chlorine and removes organics.

Activated Carbon Post Filter - removes tastes and odors to give water a final “polish” prior to delivery.

Pressurized Storage Tank - holds purified drinking and cooking water ready for use.

Chrome Plated Faucet - mounts attractively on sink or counter to deliver pure water at the touch of a lever.

Economy RO Booster Pump Model Specific ComponentsBooster Pump - raises and maintains the water pressure at the optimum level to ensure the highest TDS rejection

rate with maximum production.

Product Water Pressure Switch - shuts off system when pressure tank has been filled.

Feed Water Pressure Switch - protects pump against run dry situations.

The performance of a reverse osmosis membrane is highly dependent upon pressure, temperature and TDS. The actual volume of product water and rejection percentage willvary with differences from the test conditions that membrane ratings are based upon. These drinking water systems are not intended to be used for the treatment of water thatis microbiologically unsafe or of unknown quality.

Conditions for UseSource Water Supply Profile

Community/Private Chlorinated/Non-Chlorinated Hardness (CaCO3) <10 gpg / NSF: <350 (< 20 gpg)Feed Water Pressure* 242 – 690 kPa (35 – 100 psig) Iron (Fe) <0.1Temperature 4° – 38°C (40° – 100°F) Manganese (Mn) <0.05pH Range 3.0 – 11.0 Hydrogen Sulfide (H2S) 0.00Maximum TDS Level 2000 mg/L Residual Chlorine (Cl2) <2.0Turbidity** <1.0 NTUMaximum SDI*** <4.0

*Pressure regulator isrecommended for feed waterpressures exceeding 552 kpa(80 psig)

** Nephelometric Turbidity Unit*** Silt Density Index: Value stated

in SDI units.

Chemical Parameters Max mg/L

(1)Nominal product water ratings are based on the following conditions: Supply TDS of 250 ppm softened tap water, 50 psi (0.36 Mpa), 77°F (25°C), pH 8 and 15% recoverywith outlet to atmosphere.

(2)TDS rejection percentages are dependent on the supply conditions and the substance being measured.(3)Storage tank capacity is dependent upon pressure. For example, with a 5 psi precharge, the drawdown volume is 3.2 gallons at 60 psi; 2.8 gallons at 40 psi.

Specifications

Economy Reverse Osmosis Systems

Item Model Sediment Output Rejection Storage TankNumber Description Stages Filter Pre-Filter Membrane Post-Filter GPD(1) %(2) US Gallons(3)

2872 E50TFC-3SF 4 Spun Polypropylene Activated Carbon TFC Activated Carbon 50 up to 4.0

2873 E75TFC-3SF 4 Spun Polypropylene Activated Carbon TFC Activated Carbon 75 99% 4.0

Model E50TFC-3SF features:• Reverse osmosis membrane, nominally rated at 50 U.S. gallons per day.

• Pre-filters: 10" five (5) micron Sediment Cartridge and 10" Activated

Carbon Cartridge

• Post filter: 10" Activated Carbon Cartridge

• Non air gap faucet


Model E75TFC-3SF features:• Reverse osmosis membrane, nominally rated at 75 U.S. gallons per day.


Carbon Cartridge




108 Hydrotech

(1)Nominal product water ratings are based on the following conditions: Supply TDS of 250 ppm softened tap water, 50 psi (0.36 Mpa), 77°F (25°C), pH 8 and 15% recoverywith outlet to atmosphere.

(2)TDS rejection percentages are dependent on the supply conditions and the substance being measured.(3)Storage tank capacity is dependent upon pressure. For example, with a 5 psi precharge, the drawdown volume is 3.2 gallons at 60 psi; 2.8 gallons at 40 psi.

Specifications

Economy Reverse Osmosis Systems c/w Booster Pump

Economy Reverse Osmosis Systems WQA Approved

Item Model Sediment Output Rejection Storage TankNumber Description Stages Filter Pre-Filter Membrane Post-Filter GPD(1) %(2) US Gallons(3)

2875 EBP75TFC-3SF 4 Spun Polypropylene Activated Carbon TFC Activated Carbon 75 up to 99% 4.0

Model EBP75TFC-3SF features:

• Reverse osmosis membrane, nominally rated at 75 U.S. gallons per day.

• Booster Pump: Mounted on RO to maintain constant water pressure.


Carbon Cartridge




Model E50TFC-3NSF features:

• WQA Gold Seal tested and certified to NSF/ANSI 58


• Pre-filters: 10" five (5) micron Sediment Cartridge and 10" Activated Carbon

Cartridge



• Air gap kit


Model E75TFC-3NSF features:

• WQA Gold Seal tested and certified to NSF/ANSI 58


• Pre-filters: 10" five (5) micron Sediment Cartridge and 10" Activated Carbon

Cartridge



• Air gap kit


(1) TFC refers to reverse osmosis membranes constructed from a THIN FILM COMPOSITE(2) The daily production rate is the volume of product water produced by the system per day and is determined by testing in accordance with the procedure outlined in NSF/ANSI

Standard 58.(3) System’s Efficiency rating as verified by testing in accordance with NSF/ANSI standard 58. Efficiency rating means the percentage of the influent water to the system that

is available to the user as reverse osmosis treated water under operating conditions that approximate typical daily usage.(4) System’s Recovery rating as verified by testing in accordance with NSF/ANSI Standard 58. System’s Recovery rating means the percentage of the influent water to the membrane

portion of the system that is available to the user as reverse osmosis treated water when the system is operated without a storage tank or when the storage tank is bypassed.*PRESSURE REGULATOR IS RECOMMENDED FOR FEED WATER PRESSURES EXCEEDING 552 kPa (80 psig)

SpecificationsItem Model # of Storage Tank Vessel Vessel Vessel Vessel Daily Prod. Rate(2) Efficiency Recovery

# Description Vessels Capacity Ltr (gal) 1 2 3 4 L/day (G/day) Rating(3) % Rating(4) %2887 E50TFC-3NSF 4 6 (1.6) Sediment Filter Carbon Filter TFC(1) Membrane Carbon Filter 45.4 (12) 8.5 17.5

2888 E75TFC-3NSF 4 8.7 (2.3) Sediment Filter Carbon Filter TFC(1) Membrane Carbon Filter 100 (26.4) 14.5 25.8

The following Economy Reverse Osmosis Systems conform to NSF/ANSI 58 for the specific performance claims as

verified and substantiated by test data.

Economy RO Drinking Water Systems

Models E50TFC-3NSF and E75TFC-3NSF are tested and certified byWQA against NSF/ANSI 58 for thereduction of TDS.

Models E50TFC-3NSF and E75TFC-3NSF are WQA Tested and Certifiedagainst CSA B483.1

109Hydrotech

Reverse Osmosis Designer Faucets

The Tomlinson Designer RO Faucet comes in nine

beautiful finishes to match today's designer kitchens.

This lead-free designer faucet retrofits to most brands

and is an excellent upgrade from basic faucets that

come with most RO and other Filter Systems.

Features:

• Combines quality and style

with up-sell appeal

• Retrofits most brands

• Smooth operating ceramic

disk element

• Lever style handle

• Standard finish is highly

polished chrome; other

designer finishes available

• High reach neck design of 12"

(305 mm)

• Neck swivels easily, 360°

• Unique protective spout tip

prevents after drip

• Modular air gap (patent

pending)

• Base diameter is 2-1/4" (57 mm)

• Preinstalled tubing for quick connections

• Mounting hardware included

• NSF listed to ANSI NSF Std. 61-1999a

• Two-year warranty

The Tomlinson Contemporary RO Faucet comes in four

fabulous finishes which add high style to the high-end

kitchen.

Features:

• Elegant design complements

today’s high-end kitchens


• Lever style handle

• Protective spout tip design

prevents after-drip

• Patented modular air gap (US

patent #7,011,106)

• Internal ceramic disc provides

smooth operation

• High reach neck of 12" (305

mm); swivels easily, 360°

• Preinstalled tubing allows for

quick connections

• All mounting hardware is

included

• NSF listed to ANSI NSF Std. 61


Specifications for Contemporary ROItem # Model Description87551 Designer Air Gap RO Faucet, Polished Chrome

87552 Designer Air Gap RO Faucet, Satin Nickel

87553 Designer Air Gap RO Faucet, Antique Bronze

87554 Designer Air Gap RO Faucet, Brushed Stainless Finish

Spout Reach: 5" (127 mm)Overall Height: 12" (305 mm)Pressure Rating: 125 PSI / 8.3 BARFlow Rate at 35 PSI / 2.32 BAR: 1.0 gpm (3.785 lpm)Temperature Rating: 40°F / 4°C to 150°F / 66°CMounting Hole Diameter: Without Air Gap: 1/2" min; 1-1/8” max

Air Gap: 7/8" min; 1-1/8” maxMax. Mounting Surface Thickness: Without Air Gap: 2-3/8”

With Air Gap: 1”

Item # Model Description87540 Designer Air Gap RO Faucet, Polished Chrome87541 Designer Air Gap RO Faucet, Satin Nickel87542 Designer Air Gap RO Faucet, White87543 Designer Air Gap RO Faucet, Biscuit87544 Designer Air Gap RO Faucet, Black87545 Designer Air Gap RO Faucet, Polished Brass87546 Designer Air Gap RO Faucet, Antique Bronze87547 Designer Air Gap RO Faucet, Bright Nickel87548 Designer Air Gap RO Faucet, Brushed Stainless Finish

Spout Reach: 5" (127 mm)Overall Height: 12" (305 mm)Pressure Rating: 125 PSI / 8.3 BARFlow Rate at 35 PSI / 2.32 BAR: 1.0 gpm (3.785 lpm)Temperature Rating: 40°F / 4°C to 150°F / 66°CMounting Hole Diameter: Without Air Gap: 1/2"

Air Gap: 7/8"Max. Mounting Surface Thickness: Without Air Gap: 2-3/8”

With Air Gap: 1”

Specifications for Designer RO

The Designer ROFaucet is NSF listed toANSI Std. 61-1999A.

The Contemporary ROFaucet is NSF listed toANSI Std. 61.

110 Hydrotech

Value Faucets

The Value Faucets are the best alternative to upgrade the existing basic faucets in your home. The Value

Faucets are a unique quarter turn faucet that comes in two designs and six different finishes. These faucets are

NSF approved and are lead-free.

Features:• Elegant design complements today’s high-end kitchens

• NSF listed to ANSI NSF Std. 61 and is lead free


• Internal ceramic disc provides smooth operation

• High Neck Design which swivels 360°

• Lever style quarter turn handle

• All mounting hardware is included

• Available in two designs, six different finishes


Series 888 Specifications• Overall Height of 11.5" (292 mm)

• Swivels Easily, 360°

• Spout Reach: 5.7" (146 mm)

• Mounting Hole Diameter: ½" (12.5 mm)

• Base Diameter: 1.73" (44 mm)

• Connection*: ¼" compression nut fitting

• Operating pressure: 125 psi/8.3 bar

• Flow Rate: 1.0 gpm/3.785 lpm at 35 PSI/2.32 BAR

• Temperature Rating: 4°C/40°F to 70°C/158°F

Series 905 Specifications• Overall Height of 11.075" (281.32 mm)

• Swivels Easily, 360°

• Spout Reach: 4.75" (120 mm)

• Mounting Hole Diameter: ½" (12.5 mm)

• Base Diameter: 1.76 (44.8 mm)

• Connection*: ¼" compression nut fitting

• Operating pressure: 125 psi/8.3 bar

• Flow Rate: 1.0 gpm/3.785 lpm at 35 PSI/2.32 BAR

• Temperature Rating: 4°C/40°F to 70°C/158°F

These faucets are NSF 61approved and are lead-free.

Item # DescriptionSeries 888

87580 Faucet, Polished Chrome87581 Faucet, Brushed Nickel87584 Faucet, Black87585 Faucet, Satin Nickel87588 Faucet, Antique Brass87589 Faucet, Antique Wine

Item # DescriptionSeries 905

87582 Faucet, Polished Chrome87583 Faucet, Brushed Nickel87586 Faucet, Satin Nickel87587 Faucet, Oil Rubbed Bronze

* The standard faucets come with 1/4" compression nut fitting. The 3/8" quick connect faucetadapter fitting (#92407) can be purchased separately.

Colour Selection Ring PackItem #87591Colour Rings are available for

consumer use.

Colours included are:

Chrome Plated

Antique Brass

Antique Wine

Bright Black

Brushed Nickel

Oil Rubbed Bronze

Satin Nickel

Chrome Plated

111Hydrotech

Kemflo - Reverse Osmosis Booster Pumps

Item #92325

Nominal Maximum Flow Rate = 1.0 LPM (0.26 USGPM)

Maximum Pump Pressure = 758 kPa (110 PSI)

Maximum Inlet Pressure = 414 kPa (60 PSI)

Ambient Temperature Limits = 5 to 35°C (40 to 90°F)

Voltage = 24VDC

The Kemflo Reverse Osmosis Booster Pump can be used with

Hydrotech's 101 or 123 Series Reverse Osmosis systems from

9 to 75 GPD to provide increased pressure to the inlet of the

system for increased production and higher quality water. The

pump provides virtually noise free operation.

Pump comes complete with:• 120VAC to 24VDC Class 2 Transformer, UL Approved for the US and Canada

• Pressure Switch with 3/8" QC Fittings

• Pump inlet / outlet with ¼" QC Fittings

• Vibration Dampening Motor Mount

1 Year Limited Warranty against manufacturing defects

Aquatec Reverse Osmosis Demand Pumps

Item # 92341

Aquatec DDP 5800 Series Delivery/Demand Pump Package• complete with internal on/off pressure switch

• 115V/60 Hz

• Pressure regulated to approximately 60 psi at 1 GPM

• Pump inlet/outlet 3/8”

Key Operating Benefits:• .25 to 1.5 GPM (5 lpm) flow

• Up to 130 psi (9 bars) pressure

• Adjustable switch and bypass

settings

• Auto purging

• 7 year design life (estimated)

• Highly efficient

• Minimal pulsations

• Whisper quiet at lower flows

• Self priming

• Can run dry without damage

• Chemically resistant versions

1 Year Limited Warranty against

manufacturing defects

112 Hydrotech

Aquatec - Reverse Osmosis Booster Pumps

Aquatec booster pumps are available for reverse osmosis system installations on low pressure water supplies. A

booster pump raises and maintains the water pressure to the optimum level to ensure the highest rejection rate

and maximum production.

Distinguishing Features

Accessories

• Toughest, most durable pump on the market

• Adjustable maximum outlet psi (regardless of feed

pressure)

• Expels trapped air (no more air locks)

• Can be mounted w/pump head up or down

• More flow at extremely low inlet pressures

• New motor venting system to remove moisture

• EMI/RFI electronic noise suppression

• 100% final performance tested

• 1 year limited warranty against manufacturing

defects

Item #92319:

CDP 6800 Transformer

Item # 92318:

3/8” PSW Tank Shut-off Switch

Item #93323:

CDP 8800 Transformer

Item # 92317 Aquatec Model CDP 8800 Series Booster Pump Package• complete with PSW Shutoff Switch and 115V Transformer • suitable for R.O. Systems rated up to 120 GPD.

Item # 92317-1 Aquatec Model CDP 8800 Package with 3/8” x 1/4” Connectors and Tubing

Item # 92287 Aquatec Model CDP 6800 Series Booster Pump Package• complete with PSW Shutoff Switch and 115V Transformer • suitable for R.O. Systems rated up to 50 GPD

Key Operating Benefits:• Maximum Pump Pressure - 120 PSI (827 kPa)

• Maximum Inlet Pressure - 40 PSI (275 kPa)

• Used with membranes 9 to 50 GPD

• Up to 30,000+ operating hours (estimated)


• Self priming - 60” lift

• Low voltage (12-24V) motor for maximum

safety

• Corrosion resistant exterior

• Continuous or intermittent operation

• Supplied with 3/8” PSW Tank Shut-off switch

• Quiet - less than 45 DBA

• Pump inlet/outlet 1/4” QC

• Flexible mounting plate

Key Operating Benefits:• Maximum Pump Pressure - 120 PSI (827 kPa)

• Maximum Inlet Pressure - 40 PSI (275 kPa)

• Used with membranes 50 to 100 GPD

• Up to 15,000+ operating hours (estimated)


• Self-printing - 60” lift

• Low voltage (12-24V) motor for maximum

safety

• Corrosion resistant exterior

• Continuous or intermittent operation

• Supplied with 3/8” PSW tank shut-off switch

• Quiet - less than 52 DBA

• Pump inlet/outlet 3/8” QC

• Flexible mounting plate

CDP 6800 Dimensional Specifications

CDP 8800 Dimensional Specifications

113Hydrotech

Item #92313Features• Polypropylene construction

• Maximum Pressure = 100 psig

• Diameter: 9 3/4”, Height: 19 1/2”

RO-Pro - Reverse Osmosis Storage Tank

COMPONENT

Item #42600029Model RO-132 Features• 4.4 Gal Total Tank Volume

• Metal construction

• 1/4” NPT Stainless Steel Connection

• Diameter: 11”, Height: 13-3/4”

• Maximum Working Pressure = 100 psig

PAE - Reverse Osmosis Storage Tank

COMPONENT

RO-Pro Drawdown - with 7 psi pre-charge pressure

PAE RO-132 Drawdown - with 5 psi pre-charge

RO-Pro tanks are

manufactured by

Kemflo International

Co., Ltd. - Pingtong,

Taiwan

RO-123 tanks are

manufactured by PAE

Machinery Industrial

Co., Ltd. - Taichung,

Taiwan

114 Hydrotech

Reverse Osmosis Storage Tanks

For Commercial and Industrial Applications• 100% nonmetallic, seamless vessels will never chip, rust, dent or leak

• Removable air cell allows for easy service and sanitization, or

replacement as needed

• All materials used in construction are FDA-approved

• 125 psig maximum operating pressure; 120°F maximum operating

temperature

• Five-year warranty from the date of manufacture.

Model No. Capacity Height Diameter System Assembly Wt.(gal./liter) (in./cm.) (in./cm.) Connection (lbs./kg.)

ROmate 15 14.5 26 1/2 16 1” male 1555.1 67 41 NPT 6.8

ROmate 20 19.8 32 1/4 16 1” male 1975.2 82 41 NPT 8.6

ROmate 30 29.5 44 16 1” male 23112.1 112 41 NPT 10.5

ROmate 40 40.3 56 3/4 16 1” male 30153.1 144 41 NPT 13.6

ROmate 80 86.7 55 1/2 24 1/4 1 1/4” male 58329.5 141 62 NPT 26.4

Model No. PSI Precharge System Shutoff Pressure (gal./liter)30 40 50 60 70 80 90 100

ROmate1510 6.5 8.0 9.0 9.7 10.3 10.7 11.1 11.4

24.6 30.1 33.9 36.7 38.9 40.6 41.9 43.120 3.2 5.3 6.7 7.8 8.6 9.2 9.7 10.1

12.3 20.1 25.4 29.4 32.4 34.8 36.7 38.3

ROmate 2010 8.9 10.9 12.2 13.3 14.0 14.6 15.1 15.5

33.5 41.1 46.3 50.2 53.1 55.4 57.3 58.820 4.4 7.2 9.2 10.6 11.7 12.5 13.2 13.8

16.8 27.4 34.7 40.1 44.2 47.5 50.1 52.3

ROmate 3010 13.2 16.2 18.2 19.7 20.9 21.8 22.5 23.1

50.0 61.2 69.0 74.7 79.1 82.5 85.3 87.620 6.6 10.8 13.7 15.8 17.4 18.7 19.7 20.6

25.0 40.8 51.8 59.8 65.9 70.7 74.7 77.9

ROmate 4010 18.0 22.1 24.9 27.0 28.5 29.8 30.8 31.6

68.2 83.7 97.3 102.1 108.1 112.8 116.6 119.720 9.0 14.7 18.7 21.6 23.8 25.5 26.9 28.1

34.1 55.8 70.7 81.7 90.0 96.6 102.0 106.4

ROmate 8020 19.4 31.7 40.2 46.4 51.2 54.9 58.0 60.5

73.4 120.0 152.2175.7 193.7 207.9 219.4 228.930 X 15.9 26.8 34.8 40.9 45.8 49.7 52.9

X 60.0 101.4131.8 155.0 173.3 188.1 200.3

115Hydrotech

For each model from the RO-1 through the RO-14, the first line is the capacity in gallons with a 5 psig air charge. (0.34 bar);

the second line is the capacity in liters with a 0.34 bar air charge. For models RO-20 through RO-86, the air charge is 10

psig (0.69 bar).

AMTROL Reverse Osmosis Water Storage Tanks• The most reliable R.O. tank made - the choice for the first R.O. system ever

made...still first choice among R.O. makers today.

• Broadest line in the industry

• Meets the most demanding specifications for potable water - certified by NSF,

Standard 58. Meets U.S. FDA Spec 121.2500, Sub F.

• Keeps water tasting fresh

• Unsurpassed customer service, on time delivery and ready availability

• American made

• 5 year warranty

The Design That Has Set The StandardFifty years of innovation, quality control and

engineering excellence go into every AMTROL

tank.

• Longest lasting charge in the industry

• AMTROL’s pioneering diaphragm design provides:

longest life and most complete water discharge

• Fully enclosed polypropylene and butyl water

reservoir - ensures water purity and has less

rubber/water contact than a bladder tank

• Built to last - durable steel tank

• AMTROL is an ISO 9001 Company

Total Tank Water Capacity in Gallons (Liters) at Various System Pressures Dimensions Shipping

Model Volume psig 20 30 40 50 60 70 Diameter Height Weight

Number Gal. (Ltr) bar 1.38 2.07 2.76 3.45 4.14 4.83 cm (inches) cm (inches) kg (lbs)

RO-2 2.0 0.9 1.1 1.3 1.4 1.4 1.6 20.32 32.07 2.3

(7.6) (3.4) (4.2) (4.9) (5.3) (5.3) (6.0) (8") (12-5/8") (5)

RO-3 3.2 1.4 1.8 2.0 2.2 2.4 2.5 23.02 35.8 3.2

(12.1) (5.3) (6.8) (7.5) (8.4) (9.1) (9.5) (9-11/16") (14-3/32") (7)

RO-4 4.4 1.9 2.5 2.8 3.1 3.2 3.4 27.94 38.1 4.1

(16.7) (7.2) (9.5) (10.6) (11.7) (12.1) (12.8) (11") (15") (9)

RO-14 14.0 6.1 7.8 9.0 9.7 10.3 10.7 39.05 56.36 10.9

(53.0) (23.1) (29.5) (34.1) (36.9) (39.0) (40.5) (15-3/8") (22-3/16") (24)

RO-20 20.0 5.8 8.9 11.0 * * * 39.05 80.65 14.6

(75.7) (22.0) (33.7) (41.6) * * * (15-3/8") (31-3/4") (32)

RO-34 34.0 9.1 14.7 18.2 20.6 22.4 23.8 55.88 74.93 27.7

(128.7) (34.4) (55.6) (68.9) (78.1) (84.8) (90.1) (22") (29-1/2") (61)

RO-44 44.0 12.7 19.7 24.1 27.2 29.5 31.2 55.88 91.44 39.1

(166.6) (48.1) (74.6) (91.2) (103.0) (111.7) (118.0) (22") (29-1/2") (86)

RO-86 86.0 24.8 38.5 47.2 43.2 * * 66.04 119.86 55.8

(325.5) (93.9) (145.7) (178.7) (163.5) * * (26") (47-3/16") (123)

Reverse Osmosis Storage Tanks

116 Hydrotech

Aqua Flo Under Sink Filter Systems

Ultra 2 Under Sink Filter System• Ideal for home, farm or cottage use on

microbiologically safe water supplies.

• Filters sediment, rust and unpleasant tastes

and odors.

• Reduces levels of chlorine and sediment

down to 0.5 micron.

• Easy do-it-yourself installation.

• Includes attractive chrome plated faucet.

• Cheaper and more convenient than bottled

water.

Ultra 2 Under Sink Filter SystemNo. 26117

Replacement CartridgesNo. 26118

0.5 Micron Carbon Briquette Cartridge

No. 26006

Superior Taste Cartridge

Chrome Long Reach FaucetNo. 87511

117Hydrotech

Remote Water Chiller

Stylish and unique water chiller that fits discretely under the kitchen

sink...ready to plug in!

• Provides perfectly chilled drinking water at 39 - 42°F (4 - 6°C)

• All stainless steel waterways to use with RO system

• White powder coated galvanized steel cabinet with light gray plastic

fascia

• Easy to install with quick-connect fittings

• Four foot insulated power cord with NEMA 5-15 plug-ready to plug in

• Adjustable water temperature control

• One gallon per hour cooling capacity; stainless steel storage tank

• Air cooled; no cabinet venting required

• Includes four feet of 1/4” diameter tubing, two quick-connect fittings,

wall mounting clips and screws, instruction manual

• NSF approved

Cabinet: Powder coated galvanized steel cabinet with plastic front.

Cold Water Refrigeration Unit: Convection-cooled condenser. Internally spring mounted, hermetically sealed

compressor with automatic overload protector. No lubrication needed. Refrigerant is controlled accurately by

capillary tube. Air-cooled; designed to fit under a cabinet.

Cold Water Thermostat: Temperature is controlled by an adjustable thermostat with “OFF” position that is easily

accessible on the front of the cabinet.

Cold Water Reservoir: Evaporator is made of copper tube on stainless steel water tank and both are

encapsulated in insulation.

Capacity: 1 GPH cooling capacity.

Electrical: 115 volts, 60 Hz. Water cooler compressor hp 1/20. Insulated power cord with NEMA 5-15 polarized

plug.

Limited One Year Warranty: One year on the sealed refrigeration system and most component parts. Detailed

warranty certificate enclosed with each water cooler; sample copy available upon request.

Cooling 115 volts, 60Hz Dimensions NetItem Model Capacity1 Full Load Rated W x D x H Weight

Number Description GPH (LPH) Amps Watts Inches Lbs.

2878 R1P 1.0 (3.8) 1.3 135 10-5/16 x 8-3/4 x 14-5/8 30

(1)Capacity is at industry standard rating conditions of 50°F (10°C) outlet water, 80°F (26.7°C) inlet water and 90°F (32.2°C) ambient air.• Model covered by this specification complies with all known Plumbing Codes. Listed by Underwriters Laboratories Inc.• Components in this cooler are lead free as defined by the safe Drinking Water Act Amendments of 1986, and the Lead Contamination Control Act of 1988.• Drinking water cooler is Certified to NSF/ANSI 61.• All specifications subject to change without notice.

Specifications

Manufactured by Tri Palm International, LLC

Cienega De Flores, Mexico

Certified toNSF / ANSI 61 / Section 9

118 Hydrotech

Bottle-Free Point-of-Use Coolers

The PURA COOL is an economical

bottle-free cooler product.The

treatment system is mounted remotely

and the cooler provides hot and cold

filtered drinking water in a basic yet

sturdy platform.

Features• Hot and Cold dispensing spigots

• Hot water safety lock to prevent

accidental dispensing

• Dual float shut-off for safety

• Both remotely mounted filtration or

reverse osmosis options

• Meets UL and CSA requirements

The PURA MAX bottle-free cooler

is a product with a modern look and

feel suitable for business and

homes, but without the added

ultraviolet option of the Max Plus

model.

Features• Modern look with metallic finish

matches any décor particularly in

office environments

• 1 gallon stainless steel cold tank

• Hot and Cold dispensing spigots



• Lower cabinet is large enough to

mount either a filtration cartridge

package or a reverse osmosis

system


The PURA MAX PLUS includes a

system which re-circulates water from

the cold reservoir past an ultraviolet

sterilization lamp for continual

sanitization. This Max Plus has a

modern look and feel that is suitable

for both business and home

environments.

Features• Modern look with metallic finish

matches any décor particularly in

office environments

• Re-circulating ultraviolet sanitization

provides peace of mind

• 1 gallon stainless steel cold tank

• Hot and Cold dispensing spigots



• Lower cabinet is large enough to mount either a

filtration cartridge package or a reverse osmosis

system


With advanced features such as

“in tank” UV Sanitization and

BioCote® to inhibit biological

growth, the PURA ULTIMATE

provides an endless supply of

water with safety and security. The

Ultimate modern and yet robust

appeal and function is perfect for

installation in all applications.

Features• Three water temperature settings

meets everyone’s needs

• In tank ultraviolet sanitization

lamp maintains water quality in

the cold tank

• Lower cabinet mounts either

filtration or reverse osmosis

equipment

• BioCote® Technology protects from bacterial

growth on exterior

• Leak detection and automatic shut-off prevent

water damage

• Large 1 gallon cold tank

• 9” high filling height for pitchers

• Adjustable levelling feet

119Hydrotech

Bottle-Free Point-of-Use Coolers

Model Cold Tank Capacity Hot Tank Capacity Electrical Dimensions Water Dispensing Areausgal (L) usgal (L) H x W x D inches (mm) Connection Height inches (mm)

PURA Cool 1.2 (4.5) 0.9 (3.5) 120V/60Hz/6.2A 39x12x12 (980x312x314) 1/4” tube 7.75 (197)PURA Max 0.9 (3.5) 0.4 (1.5) 120V/60Hz/4.7A 42x13x15 (1060x330x380) 1/4” tube 7.5 (190)

PURA Max Plus 0.9 (3.5) 0.4 (1.5) 120V/60Hz/4.7A 42x13x15 (1060x330x380) 1/4” tube 7.5 (190)PURA Ultimate 1.2 (4.5) 0.4 (1.5) 120V/60Hz/6.2A 46x16x15 (1160x410x380) 1/4” tube 9.0 (228)

Model Removable Cold Hot Room Temp. Reserve Storage Leak UV BioCote NSF Filtration ReverseDrip Tray Water Water Water Tank usgal (L) Detection Protection 61 Osmosis

PURA Cool � � � — — — — — — Remote RemotePURA Max � � � — — � — — — � �

PURA Max Plus � � � — — � � — — � �PURA Ultimate � � � � 3 (11) � � � � � �

Municipal/ Chlorinated/ pH Maximum Turbidity Maximum Hardness Iron Manganese Hydrogen ResidualPrivate Non-Chlorinated Range TDS SDI (Fe) (Mn) Sulphide (H2S) Chlorine (Cl)

Filtration both both 3.0-11.0 <500 mg/L <1.0 NTU — <350 mg/L <0.1 mg/L <0.05 mg/L <0.0 mg/L <0.0 mg/LEquipped Coolers recommended (<20gpg)Reverse Osmosis both both 3.0-11.0 <500 mg/L <1.0 NTU <4.0 <350 mg/L <0.1 mg/L <0.05 mg/L <2.0 mg/L <2.0 mg/LEquipped Coolers recommended (<20gpg)

Specifications

Source Water Supply Profile

Electrical: 120V/60Hz Grounded North American electrical outletInlet Water Pressure: 40 - 60 psi (275-414 kPa) Recommended / 100 psi (862 kPa) MaximumInlet Water Temperature: 40 - 100°F (4 - 38°C)Drain Connection: Required for coolers equipped with reverse osmosis

PURA Point-of-Use Coolers producebottle quality water.

• UV Light - Without harmful chemicals, ultraviolet light

sanitizes water to protect you from bacteria.

• BioCote® - A new technology offering antimicrobial

protection against the fungi, mold, and bacteria to

reduce unpleasant odors.

• Activated Carbon Filtering - reduces chlorine taste and odor.

• Sediment Filtering - reduces turbidity and sediments.

• Reverse Osmosis - WaterGroup’s 1240 Series reverse osmosis

technology reduces total dissolved solids in the water.

120 Hydrotech

Leak Controller

The first line of defense against water damage.Leak Controller detects the water spill on the surface and engages a shut-off valve

to cut-off the water supply. It also sounds an alarm to alert the customer until the

valve is manually reset. By preventing the continuous water flow, equipment and

property damage are restricted and the user liability is reduced.

It can be connected to the water purification system, POU coolers, refrigerators, ice

makers etc.

Features• Available valve to tubing connection sizes: 1/4” for plastic and copper tubing

• LeakLogic™ RISC based management - state of the art microchip technology forsensitive controls, operation verification and long battery life

• Status test button

• Audio and LED status indicator

• Audio alarm

• Powered by 4 “AA” batteries - no external electrical connections required• Pull-out battery holder for convenient battery replacement

• Programmable service reminder

• NSF approved automatic ball valve shut-off and plastic tubing

• Two screw mounting plate allows for quick and simple installation

• Sensor towel

• Built with superior impact resistant ABS plastic

• One sensor included with coin test slot and series connectors

• Built with reinforced nylon and glass materials on stressed components

• Water detection sensitivity down to 2 ppm TDS (Total Dissolved Solids)

• Programmable service reminder indicator

• Conformal coating on the printed circuit board

• One Year Limited Warranty from date of purchase against defects in material and workmanship

Power 4 “AA” size alkaline type batteriesSensor Electromechanical dual probe with series connectorsTemperature System operating range: 40° to 100°F (4° to 37°C)

Water operating range: 36° to 140°F (2° to 60°C)Size (H x W x D) 6.75 x 3.25 x 2.5” (171 x 83 x 64 mm)Weight 0.9 lbs (0.4 kg) with batteriesSolenoid 6V DC Push-TypeAlarm 85+dB at 5’ @ 3.4 ± 0.5 kHz pulsing alarmLED BlueMounting Accessories and bracket supplied for wall mountingBattery Replacement Replace annually or upon low battery indicator

- This product does not guarantee the prevention of water damage.- Many factors increase the probability of preventing water damage including: Constant Leak Controller testing / Physical

verification of all parts / Correct placement of the sensor(s)

Specifications

Manufactured by Water Controller Products

Livermore, California

Item #92434

121Hydrotech

John Guest PI Range Quick Connect Fittings

John Guest PI Range of quick connect fittings are

now available for your fluid connection needs. The PI

Range of inch-size push-in fittings is offered for tube

sizes 5/32" O.D. to 5/8" O.D. The fittings are

manufactured in gray acetal copolymer with food

grade nitrile ‘o’ ring, making them especially suitable

for applications involving foodstuff and potable liquids.

They are equally suitable for air and inert gasses and

can therefore be used on CO2 lines, pneumatic

applications, and vacuum.

Most John Guest fittings come in packages of ten.

Consult the attached list of the John Guest fittings

currently available and package details.

Please contact customer service for current pricing and stock status.

Notes

122 Hydrotech

drinking water systems - reverse osmosis, water ... files/undersink ro.pdf · reverse osmosis...

Documents