2010-06-15

5011699700-S2S0

DVP-1160070-01

- 1 -

ENGLISH Thank you for choosing Delta DVP-SS2. DVP-SS2 is a 14-point (8DI + 6DO) PLC MPU, offering various instructions and with 8k steps program memory, able to connect to all DVP-S series extension models, including digital I/O (max. 480 I/O points) and analog modules (for A/D, D/A conversion and temperature measurement). 4 groups of high-speed (10kHz) pulse output satisfy all kinds of applications. DVP-SS2 is small in size and easy to install. a This instruction sheet only provides introductory information on electrical

specifications, general specifications, installation and wiring. For detailed information on programming and instructions, please refer to DVP-SS2 Operation Manual: Programming. For information about optional peripherals, please see individual product instruction sheet enclosed with DVP-SS2.

a This is an OPEN TYPE device and therefore should be installed in an enclosure free of airborne dust, humidity, electric shock and vibration. The enclosure should prevent non-maintenance staff from operating the device (e.g. key or specific tools are required to open the enclosure) in case danger and damage on the device may occur.

a DO NOT connect input AC power supply to any of the I/O terminals; otherwise serious damage may occur. Check all the wiring again before switching on the power. Make sure the ground terminal is correctly grounded in order to prevent electromagnetic interference. DO NOT touch any terminals when the power is switched on.

Product Profile

[ Figure 1 ]

25.20 60.00

EXTENSIONPORT90.00

3.00

3.001

2

3

4

5

6

7

8

9

10

11

4

12

13

14

Unit: mm 1. POWER, RUN, ERROR indicator 8. Nameplate 2. RUN/STOP switch 9. Extension port 3. I/O port for program communication (RS-232) 10. DIN rail mounting slot (35mm) 4. DIN rail clip 11. Extension unit clip 5. I/O terminals 12. RS-485 communication port 6. I/O point indicator 13. Mounting rail for extension module 7. Mounting hole for extension module 14. DC power input

Electrical Specifications Model

Item DVP14SS211R DVP14SS211T

Power supply voltage24VDC (-15% ~ 20%) (with counter-connection protection on the polarity of DC input power) DVPPS01(PS02): input 100-240VAC, output 24VDC/1A(PS02: 2A)

Inrush current Max. 7.5A@24VDC

- 2 -

ModelItem DVP14SS211R DVP14SS211T

Fuse capacity 1.85A/30VDC, Polyswitch Power consumption 1.8W 1.5W Power protection With counter-connection protection on the polarity of DC input power Insulation resistance > 5M (all I/O point-to-ground: 500VDC)

Noise immunity ESD: 8kV Air Discharge EFT: Power Line: 2kV, Digital I/O: 1kV, Analog & Comm. I/O: 250kKV RS: 26MHz ~ 1GHz, 10V/m

Grounding The diameter of grounding wire cannot be smaller than the wire diameter of terminals L and N (All DVP units should be grounded directly to the ground pole).

Operation / storage Operation: 0C ~ 55C (temp.), 50 ~ 95% (humidity), Pollution degree2Storage: -25C ~ 70C (temp.), 5 ~ 95% (humidity) Vibration / shock resistance

International standards: IEC61131-2, IEC 68-2-6 (TEST Fc)/IEC61131-2 & IEC 68-2-27 (TEST Ea)

Weight (g) 97g 82.5g

Input Point Spec.Items 24VDC (-15% ~ 20%) single common port input Input No. X0 ~ X3 X4 ~ X7 Input type DC (SINK or SOURCE) Input Current ( 10%) 24VDC, 5mA Input impedance 4.7k Max. frequency 20kHz 10kHz

OffOn > 15VDC Action level OnOff < 5VDC

OffOn < 10s < 20s Response time OnOff < 20s < 50s Filter time Adjustable within 0 ~ 20ms by D1020 (Default: 10ms)

Output Point Spec.Items Relay Transistor Output No. Y0 ~ Y5 Y0 ~ Y3 Y4, Y5 Max. frequency 1Hz 10kHz 1kHz Working voltage 250VAC, < 30VDC 5 ~ 30VDC #1

Resistive 1.5A/1 point (5A/COM) 0.5A/1 point (3A/COM) Inductive #2 15W (30VDC) Max. load

Lamp 20WDC/100WAC 2.5W (30VDC) OffOn 20s 100s Response

time OnOff Approx. 10ms 30s 100s #1: UP, ZP must work with external auxiliary power supply 24VDC (-15% ~ +20%), rated

consumption approx. 1mA/point. #2: Life curves

Contact Current(A)0.50.1 0.2

50

0.3 0.7 1 2

200300

500

100

100020003000

Ope

ratio

n(X

10)3

120VAC Resistive30VDC Inductive(t=7ms)

240VAC Inductive(cos 0.4)=120VAC Inductive(cos =0.4)

30VDC Inductive (t=40ms)

[ Figure 2 ]

- 3 -

I/O Configuration Input Output I/O Configuration

Model Point Type Point Type Relay Transistor

14SS211R Relay

14SS211T

8 DC

(Sink Or Source) 6

Transistor

S/SX0X1X2

X5X6X7

Y0Y1Y2

Y3Y4Y5

X4

C0

C1

X3

S/SX0X1X2

X5X6X7

ZP

Y0Y1

Y4Y5

X4

UP

Y3

X3

Y2

Note: The layout of output terminals on DVP-SS2 is different from that on DVP-SS.

Dimension & Installation Please install the PLC in an enclosure with sufficient space around it to allow heat dissipation, See [Figure 3]. y Direct Mounting: Use M4 screw according to the

dimension of the product. y DIN Rail Mounting: When mounting the PLC to

35mm DIN rail, be sure to use the retaining clip to stop any side-to-side movement of the PLC and reduce the chance of wires being loose. The retaining clip is at the bottom of the PLC. To secure the PLC to DIN rail, pull down the clip, place it onto the rail and gently push it up. To remove the PLC, pull the retaining clip down with a flat screwdriver and gently remove the PLC from DIN rail.

Wiring 1. Use 22-16AWG (1.5mm) single or multiple core wire

on I/O wiring terminals. See the figure in the right hand side for its specification. PLC terminal screws should be tightened to 1.90 kg-cm (1.65 in-lbs) and please use only 60/75C copper conductor.

22-16AWG

< 1.5mm

2. DO NOT wire empty terminal. DO NOT place the I/O signal cable in the same wiring circuit.

3. DO NOT drop tiny metallic conductor into the PLC while screwing and wiring. Tear off the sticker on the heat dissipation hole for preventing alien substances from dropping in to ensure normal heat dissipation of the PLC.

Power Supply The power input of DVP-SS2 is DC. When operating DVP-SS2, please note the following points: 1. The power is connected to two terminals, 24VDC and 0V, and the range of power is

20.4 ~ 28.8VDC. If the power voltage is less than 20.4VDC, the PLC will stop running, all outputs will go Off, and the ERROR indicator will start to blink continuously.

2. The power shutdown for less than 10ms will not affect the operation of the PLC. However, the shutdown time that is too long or the drop of power voltage will stop the operation of the PLC, and all outputs will go off. When the power returns to normal

- 4 -

status, the PLC will automatically resume the operation. (Please take care of the latched auxiliary relays and registers inside the PLC when doing the programming).

Safety Wiring Since DVP-SS2 is only compatible with DC power supply, Deltas power supply modules (DVPPS01/DVPPS02) are the suitable power supplies for DVP-SS2. We suggest you install the protection circuit at the power supply terminal to protect DVPPS01 or DVPPS02. See the figure below.

c AC power supply:100 ~ 240VAC, 50/60Hz d Breaker e Emergency stop: This button cuts off the system power supply when accidental

emergency takes place.

f Power indicator g AC power supply load h Power supply circuit protection fuse (2A) i DVPPS01/DVPPS02 j DC power supply output: 24VDC, 500mA k DVP-PLC (main processing unit) l Digital I/O module

Input Point Wiring There are 2 types of DC inputs, SINK and SOURCE. (See the example below. For detailed point configuration, please refer to the specification of each model.)

y DC Signal IN SINK mode Input point loop equivalent circuit

y DC Signal IN SOURCE mode Input point loop equivalent circuit

24G

+24V

S/S

X0

X1

[ Figure 5 ]

+24V

24G

S/S

X0

X1

[ Figure 6 ]

Output Point Wiring 1. DVP-SS2 has two output modules on it, relay and transistor. Be aware of the

connection of shared terminals when wiring output terminals. 2. Output terminals, Y0, Y1, and Y2, of relay models use C0 common port; Y3, Y4, and

Y5 use C1 common port. See [Figure 7]. When the output points are enabled, their corresponding indicators on the front panel will be on.

- 5 -

3. Output terminals, Y0 ~Y5 of transistor models use UP, ZP common port. See [Figure 8].

4. Isolation circuit: The optical coupler is used to isolate signals between the circuit

inside PLC and input modules.

y Relay (R) output circuit wiring

c DC power supply d Emergency stop: Uses external switch e Fuse: Uses 5~10A fuse at the shared terminal of output contacts to protect the output circuit f Transient voltage suppressor (SB360 3A 60V): Extends the life span of contact.

1. Diode suppression of DC load: Used when in smaller power [Figure 10a] 2. Diode + Zener suppression of DC load: Used when in larger power and frequent On/Off

[Figure 10b]

g Incandescent light (resistive load) h AC power supply i Manually exclusive output: For example, Y3 and Y4 control the forward running and reverse

running of the motor, forming an interlock for the external circuit, together with the PLC internal program, to ensure safe protection in case of any unexpected errors.

j Absorber: Reduces the interference on AC load [Figure 11] y Transistor (T) output circuit wiring

- 6 -

c DC power supply d Emergency stop e Circuit protection fuse f The output of the transistor model is open collector. If Y0/Y1 is set to pulse output, the

output current has to be bigger than 0.1A to ensure normal operation of the model. 1. Diode suppression: Used when in smaller power [Figure 13a] 2. Diode + Zener suppression: Used when in larger power and frequent On/Off [Figure 13b]

g Manually exclusive output: For example, Y3 and Y4 control the forward running and reverse running of the motor, forming an interlock for the external circuit, together with the PLC internal program, to ensure safe protection in case of any unexpected errors.

RS-485 Wiring

Figure 14

D+ D- D+ D- D+ D-

3

1 2 2

3

c Master node d Slave node e Terminal resistor

Note: 1. Terminal resistors are suggested to be connected to master and the last slave with resistor value of 120.

2. To ensure communication quality, please apply double shielded twisted pair cable (20AWG) for wiring.

- 7 -

DVPDVP-SS2 148 + 6

PLC 8k steps I/O 480

A/DD/A10kHz a

DVP-SS2

a OPEN TYPE/

a

y 1 [Figure 1]mm

1. USB 8. 2. RUNSTOP 9. I/O 3. COM1 (RS-232) 10. DIN (35mm) 4. DIN 11. I/O 5. 12. COM2 (RS-485) 6. 13. I/O 7. I/O 14.

DVP14SS211R DVP14SS211T

24VDC (-15% ~ 20%) () DVPPS01(PS02) 100-240VAC 24VDC/1A (PS02: 2A) Max. 7.5A@24VDC 1.85A/30VDC(Polyswitch) 1.8W 1.5W protection

> 5M ( 500VDC)

ESD: 8kV Air Discharge EFT: Power Line: 2kV, Digital I/O: 1kV, Analog & Comm. I/O: 250kV RS: 26MHz ~ 1GHz, 10V/m

PLC

0C ~ 55C50 ~ 95% 2 -25C ~ 70C5 ~ 95%

IEC61131-2, IEC 68-2-6 (TEST Fc)/IEC61131-2 & IEC 68-2-27 (TEST Ea)

97g 82.5g

- 8 -

24VDC (-15% ~ 20%) No. X0 ~ X3 X4 ~ X7 S/S SINK SOURCE (10%) 24VDC, 5mA 4.7k Ohm 20kHz 10kHz

OffOn > 15VDC OnOff < 5VDC OffOn < 10s < 20s OnOff < 20s < 50s D1020 0 ~ 20 ms (10ms)

No. Y0 ~ Y5 Y0 ~ Y3 Y4, Y5 1Hz 10kHz 1kHz 250VAC, < 30VDC 5 ~ 30VDC #1

1.5A /1 (5A/COM) 0.5A/1 (3A/COM) #2 15W (30VDC)

20WDC/100WAC 2.5W (30VDC) OffOn 20s 100s OnOff

10ms 30s 100s

#1UP, ZP 24VDC (-15% ~ +20%) 1mA/ #2[Figure 2]

/ I/O

14SS211R 14SS211T

8

(Sink or Source)6

DVP-SS

PLC PLC 3[Figure 3] y M4 y DIN 35mm DIN

I/O I/O

1. / 22-16AWG (1.5mm) 3

PLC 1.90 kg-cm (1.65 in-lbs) 60/75C

- 9 -

2. 3. PLC

DVP-SS2 1. 24VDC 0V 20.4 ~ 28.8VDC

20.4VDCPLC OffERROR LED 2. 10msPLC

PLC OffPLCPLC

DVP-SS2 DC Only (DVPPS01/DVPPS02) DVP-SS2 DVPPS01/DVPPS02 4[Figure 4]

c 100 ~ 240VAC, 50/60Hz d e f g h 2A i DVPPS01/DVPPS02 j 24VDC500mA k DVP PLC l /

DCSINK SOURCE

4[Figure 5][Figure 6]

1. DVP-SS2 PLC

2. Y0Y1Y2 C0Y3Y4Y5 C1

5[Figure 7] 3. Y0 ~Y5 UPZP 5[Figure 8] 4. PLC

y 5 [Figure 9] ~ [Figure 11]

c d e 5 ~ 10A f

1. DC 5[Figure 10a]2. DC +Zener On/Off

5[Figure 10b]

g h i Y3 Y4

PLC

j 5[Figure 11]

- 10 -

y 5 ~ 6 [Figure 12] ~ [Figure 13b]

c d e f

1. DC 6[Figure 13a]2. DC+Zener On/Off

6[Figure 13b]

g Y3 Y4 PLC

RS-485 6[Figure 14]

c d e 1. 120

2. (20AWG)

- 11 -

DVPDVP-SS2 148 + 6PLC 8k steps I/O/ 480A/DD/A10kHz a

DVP-SS2

a (OPEN TYPE)

a

y 1 [Figure 1]mm

1. USB 8. 2. RUNSTOP 9. I/O 3. COM1 (RS-232) 10. DIN (35mm) 4. DIN 11. I/O 5. 12. COM2 (RS-485) 6. 13. I/O 7. I/O 14.

DVP14SS211R DVP14SS211T

24VDC (-15% ~ 20%) () DVPPS01(PS02) 100-240VAC 24VDC/1A (PS02: 2A) Max. 7.5A@24VDC 1.85A/30VDC (Polyswitch) 1.8W 1.5W > 5M ( 500VDC)

ESD: 8kV Air Discharge EFT: Power Line: 2kV, Digital I/O: 1kV, Analog & Comm. I/O: 250kV RS: 26MHz ~ 1GHz, 10V/m

PLC

0C ~ 55C50 ~ 95% 2 -25C ~ 70C5 ~ 95%

IEC61131-2, IEC 68-2-6 (TEST Fc)/IEC61131-2 & IEC 68-2-27 (TEST Ea)

97g 82.5g

- 12 -

24VDC (-15% ~ 20%) No. X0 ~ X3 X4 ~ X7 S/S (10%) 24VDC, 5mA 4.7k Ohm 20kHz 10kHz

OffOn > 15VDC OnOff < 5VDC OffOn < 10s < 20s OnOff < 20s < 50s D1020 0 ~ 20 ms (10ms)

No. Y0 ~ Y5 Y0 ~ Y3 Y4, Y5 1Hz 10kHz 1kHz LED ON OFF 250VAC, < 30VDC 5 ~ 30VDC #1

1.5A /1 (5A/COM) 0.5A/1 (3A/COM) #2 15W (30VDC)

20WDC/100WAC 2.5W (30VDC) OffOn 20s 100s OnOff

10 ms 30s 100s

#1UP, ZP 24VDC (-15% ~ +20%) 1mA/ #2[Figure 2]

/ I/O

14SS211R 14SS211T

8

() 6 (NPN)

DVP-SS

PLC PLC 3[Figure 3] y M4 y DIN 35mm DIN

I/O I/O 1. / 22-16AWG (1.5mm) 3

- 13 -

PLC 1.90 kg-cm (1.65 in-lbs) 60/75C 2. 3. PLC

DVP-SS2 1. 24VDC 0V 20.4VDC ~ 28.8VDC

20.4VDCPLC OffERROR LED 2. 10msPLC

PLC OffPLCPLC

DVP-SS2 DC Only (DVPPS01/DVPPS02) DVP-SS2 DVPPS01/DVPPS02 4[Figure 4] c 100 ~ 240VAC, 50/60Hz d e f g h 2A i DVPPS01/DVPPS02 j 24VDC500mA k DVP PLC l / DCDC 4~5[Figure 5][Figure 6]

1. DVP-SS2 PLC-NPN-PNP

2. Y0Y1Y2 C0Y3Y4Y5 C1

5[Figure 7] 3. (NPN/PNP) Y0~Y5 UPZP 5

[Figure 8] 4. PLC y!!

5 [Figure 9] ~ [Figure 11] c d e 5 ~ 10A f

1. DC 5[Figure 10a]2. DC+Zener On/Off 5

[Figure 10b] g h i Y3 Y4

PLC j 5[Figure 11]

- 14 -

y!! 5 ~ 6 [Figure 12] ~ [Figure 13b] c d e f

1. DC 6[Figure 13a]2. DC+Zener On/Off

6[Figure 13b] g Y3 Y4

PLC

RS-485 6[Figure 14] c d e 1. 120

2. (20AWG)

- 15 -

....... TRKE .........

Deltann DVP-SS2 modelini setiiniz iin teekkrler. DVP-SS2 PLC 8k program hafzas ile eitli komutlar sunar ve zerinde 14 nokta vardr (8DI + 6 DO). PLCye Dijital giri/k modlleri (max. 480 giri/k nokta) ve analog modller (A/D, D/A dntrc ve scaklk niteleri). ki grup yksek-hzl (10kHz) pulse k ve yeni 4-eksen interpolasyon komutlar ile birok uygulama iin tatmin edici zmler sunar. DVP-SS2 rn kk lsyle kurulumu ok kolaydr. a Bu bilgi dkman sadece rnn elektriksel zellikleri, genel fonksiyonlar, kurulumu

ve balants ile ilgili bilgiler salar. Detayl programlama ve DVP-SS2 uygulama komutlar ile ilgili ltfen DVP-SS2 Operation Manual: Programming dkmann inceleyiniz. Opsiyonel evre birimleri ile ilgili ltfen kutunun iindeki rnle birlikte gelen bilgi dkmann inceleyiniz.

a Bu rn AIK TP bir PLCdir. PLC rn toz, rutubet, elektrik oku riski ve titreimden uzak yerlerde muhafaza edilmelidir. Ayrca cihaza yetkili olmayan kiilerin mdahale etmesini engelleyecek nlemler alnmaldr. (rnein rnn kurulduu panoya kilit konulmas gibi). Aksi halde kullanclar ve/veya PLC zarar grebilir.

a Giri/k terminallerine kesinlikle AC besleme balamaynz. Aksi halde rn zarar grebilir. Enerji vermeden nce rnn tm balantlarn kontrol ediniz. Elektromanyetik grlty nlemek iin topraklamann dzgn yapldna emin olunuz. Enerjili iken rn terminallerine mdahale etmeyiniz.

rn Grn y ngilizce (English) blmnde ekil 1ye [Figure 1] baknz. Birim: mm.

Elektriksel zellikler Model

Madde DVP14SS211R DVP14SS211T

Besleme voltaj 24VDC (-15% ~ 20%) (DC giri besleme ters balant korumas) DVPPS01(PS02): giri 100-240VAC, k 24VDC/1A(PS02: 2A)

Sznt Akm Maksimum 7.5A@24VDC

Sigorta Kapasitesi 1.85A/30VDC, Polyswitch

G Tketimi 1.8W 1.5W

Besleme Koruma DC giri besleme ters balant korumas

Izolasyon direnci > 5M (Tm I/O nokta - ground: 500VDC)

Ses Bakl ESD: 8kV Air Discharge EFT: Power Line: 2kV, Digital I/O: 1kV, Analog & Comm. I/O: 250kV RS: 26MHz ~ 1GHz, 10V/m

Topraklama Topraklama kablosunun kesiti 24V - 0V terminalleri kablolar kesitinden kk olmamaldr. (Tm DVP rnleri dorudan ground ucundan topraklanmaldrlar).

alma/Saklama alma: 0C ~ 55C (scaklk), 50 ~ 95% (rutubet), Kirlenme derece 2Saklama: -25C ~ 70C (scaklk), 5 ~ 95% (rutubet)

Titreim/ok direnci Uluslararas Standartlar: IEC61131-2, IEC 68-2-6 (TEST Fc)/IEC61131-2 & IEC 68-2-27 (TEST Ea)

Arlk (g) 97g 82.5g

Giri Noktas zellik.Madde 24VDC (-15% ~ 20%) tek ortak u girii

Giri No. X0 ~ X3 X4 ~ X7

- 16 -

Giri Noktas zellik.Madde 24VDC (-15% ~ 20%) tek ortak u girii

Giri Tipi DC (SINK veya SOURCE)

Giri Akm ( 10%) 24VDC, 5mA

Giri Empedans impedance 4.7k Ohm

Maksimum frekans 20kHz 10kHz

OffOn > 15VDC Aktif seviye

OnOff < 5VDC OffOn < 10s < 20us Cevap

Zaman OnOff < 20s < 50us Filtre zaman D1020 datasndan 0 ~ 20ms (Default: 10ms)

k Noktas zellikMadde Rle Transistor

k No. Y0 ~ Y5 Y1, Y3 Y4, Y5

Maksimum frekans 1Hz 10kHz 1kHz

alma Voltaj 250VAC, < 30VDC 5 ~ 30VDC #1

Rezistif 1.5A /1 nokta (5A/COM) 0.5A/1 nokta (3A/COM)

Endktif #2 15W (30VDC) Maksimum Yk Lamba 20WDC/100WAC 2.5W (30VDC)

OffOn 20s 100s Cevap Zaman OnOff

Yaklak 10ms 30s 100s

#1: UP, ZP harici 24VDC (-15% ~ +20%) g kayna ile alr, g tketimi oran yaklak 1mA/nokta.

#2: ngilizce (English) blmnde ekil 2ye [Figure 2] baknz.

I/O Konfigurasyon Giri k I/O konfigurasyon

Model Nokta Tip Nokta Tip Rle Transistor

14SS211R Rle

14SS211T 8

DC (Sink veya

Source) 6

Transistor

ngilizce (English)

blmnde baknz

ngilizce (English)

blmnde baknz

Not: DVPSS2 zerindeki k terminallerinin yerleim plan DVP-SSde olduundan farkldr.

ller & Kurulum Ltfen PLCnin kurulumunu yaparken s dalmnn verimli olmas iin evresinde gerekli boluun brakldna emin olunuz. Ltfen ngilizce (English) blmnde ekil 3e [Figure 3] baknz.

y Dorudan Montaj: rnn llerine gre ltfen M4 vida kullannz. y DIN Ray Montaj: PLC rn 35mm DIN rayna monte edilecei zaman, rnn hareket ederek kablo balantlarnn zarar grmesini engellemek iin sabitleyici klipsleri kullannz. Sabitleyici klipsler PLCnin altnda olup, PLCyi DIN rayna sabitlemek iin bu klipsleri bastrnz. PLCyi yerinden karmak iinse ince tornavida yardm ile nce bu klipsleri anz ve PLCyi DIN rayndan ekerek kartnz.

- 17 -

Balant 1. PLCnin I/O terminal balantlarn yapmak iin

22-16AWG (1.5mm) tek damarl veya ok damarl kablo kullannz. Kablo zellikleri yandaki ekilde gsterildii gibi olmaldr. PLC terminal vidalar 1.90 kg-cm (1.65 in-lbs) orannda sklmal ve sadece bakr iletkenler kullanlmaldr.

22-16AWG

< 1.5mm

2. Bo terminallere balant yapmaynz ve I/O sinyal kablolar ile power kablolarn ayr kablo bloundan balaynz.

3. PLC kablo balantlarn yaparken PLCnin iine iletken paracklar drmeyiniz. Balantlar tamamladktan sonra s dalmn salanabilmesi iin kk cisimlerin PLCnin iine dmesini engelleyen koruyucu etiketleri kartnz.

G Kayna (Power Supply) DVP-SS2 serisi rnlerin besleme girii DCdir. DVP-SS2 serisi rnleri kullanrken aadaki uyarlara dikkat ediniz: 1. Besleme, 24VDC ve 0V terminallerine balanmal ve besleme voltaj 20.4 ~

28.8VDC aralnda olmaldr. Eer besleme voltaj 20.4VDC altna derse, PLC almay durdurur, tm klar OFF olur ve ERROR indikatr srekli flash yapar.

2. 10 ms altndaki enerji kesintisi PLCnin almasna etki etmeyecektir. Fakat daha uzun sureli bir enerji kesintisi veya voltaj dmesi durumunda PLC almas duracak ve tm klar OFF olacaktr. PLCnin beslemesi normal duruma dndnde, PLC otomatik olarak normal almasna geri dner. (PLC programlanaca zaman iindeki kalc rle ve registerlerin kullanmna dikkat ediniz).

Gvenli Balant DVP-SS2 rnleri sadece DC voltaj ile beslenir. DELTAnn g kaynaklar (DVPPS01 / DVPPS02), DVP-SS2 PLClerin beslemesi iin uygundur. DVPPS01 veya DVPPS02 rnlerini korumak iin power supply terminallerine koruyucu devre kurulmas nerilir. ngilizce (English) blmnde ekil 4e [Figure 4] baknz. 1 AC power supply:100 ~ 240VAC, 50/60Hz 2 Devre kesici 3 Acil Stop: Acil durumda sistemin enerjisini kesmek iin kullanlr. 4 Power indikatr 5 AC power supply yk 6 Power supply devre koruma sigortas (2A) 7 DVPPS01/DVPPS02 8 DC power supply k: 24VDC, 500mA 9 DVP-PLC (Ana ilemci birimi) V Digital I/O modl Giri Balants 2 eit DC giri vardr, SINK veya SOURCE. ngilizce (English) blmde ekil 5e [Figure 5] ve ekil 6ya [Figure 6] baknz.

k Balants 1. DVP-SS2 serisi rnlerde 2 eit k vardr. Rle ve Transistr (NPN/PNP). k

terminal balantlarn yaparken ortak terminallerin kullanmna dikkat ediniz. (COM). 2. Y0, Y1, ve Y2 k terminalleri C0 ortak ucunu, Y3, Y4 ve Y5 k terminalleri C1

ortak ucunu kullanr. ngilizce (English) blmde ekil 7ye [Figure 7] baknz. k terminallerinden biri aktif olursa o k terminaline karlk gelen indicator ON olur.

3. Y0 ~Y5 transistr k terminalli (NPN/PNP) modeller UP, ZP ortak ularn kullanr. ngilizce (English) blmde ekil 8e [Figure 8] baknz.

4. zolasyon devresi: PLC i devreleri ve giri modlleri arasn izole etmek iin optokuplr kullanlr.

- 18 -

y Rle (R) k devre balants Balant detay iin ngilizce (English) blmde ekil 9a - ekil 11e [Figure 9] ~ [Figure 11] baknz. 1 DC power supply 2 Acil stop: Harici switch kullanr. 3 Sigorta: k devrelerini korumak iin klarn ortak terminallerinde 5~10A sigorta kullanr. 4 Yksek gerilim darbe koruyucu (SB360 3A 60V): Kontak mrn uzatmak iin kullanlr.

1. DC yk diyot koruma: Dk power olduu zaman kullanlr. (ngilizce (English) blmde ekil 10aya [Figure 10a] baknz).

2. DC yk Diyot + Zener koruma: Yksek power veya ok sk On/Off durumlarda kullanlr. (ngilizce (English) blmde ekil 10bye [Figure 10b] baknz)

5 Akkor Lamba (resistif yk) 6 AC power supply 7 Manual tek k: rnein, Y3 ve Y4 klar motorun ileri ve geri almasn kontrol etsin.

klarn ayn anda almasn ve beklenmeyen hatalar nlemek iin PLC programnda ve harici devre balantsnda gerekli nlemler alnarak ayn anda sadece tek kn almas salanabilir.

8 Dalga Emici (Absorber): AC ykteki grlty nlemek iin kullanlr. (ngilizce (English) blmde ekil 11e [Figure 11] baknz)

y Transistr (T) k devre balants Balant detay iin ngilizce (English) blmde ekil 12 ~ ekil 13bye [Figure 12] ~ [Figure 13] baknz.

1 DC power supply 2 Acil stop 3 Devre koruma sigortas 4 Transistor kl modeler ak kolektr(open collector) dr. Eer Y0/Y1 pulse k olarak

ayarlandysa, normal alma iin k akm 0.1Aden byk olmaldr. 1. Diyot koruma: Dk power olduu zaman kullanlr. (ngilizce (English) blmde

ekil 13aya [Figure 13a] baknz) 2. Diyot + Zener koruma: Yksek power veya ok sk On/Off durumlarda kullanlr

(ngilizce (English) blmde ekil 13bye [Figure 13b] baknz)

5 Manual tek k: rnein, Y3 ve Y4 klar motorun ileri ve geri almasn kontrol etsin. klarn ayn anda almasn ve beklenmeyen hatalar nlemek iin PLC programnda ve harici devre balantsnda gerekli nlemler alnarak ayn anda sadece tek kn almas salanabilir.

RS-485 Wiring ngilizce (English) blmde ekil 14ye [Figure 14] baknz.

1 Master istasyon 2 Slave istasyon 3 Terminal resistor Not: 1. Terminal resistorun master ve son slave arasnda 120W olacak ekilde balanlmas nerilir. 2. Haberleme kalitesini arttrmak iin, ltfen balantda double shield (ift ekranl) twisted pair

(sarmal iftli) kablo (20AWG) kullannz.

/ColorImageDict > /JPEG2000ColorACSImageDict > /JPEG2000ColorImageDict > /AntiAliasGrayImages false /CropGrayImages true /GrayImageMinResolution 300 /GrayImageMinResolutionPolicy /OK /DownsampleGrayImages true /GrayImageDownsampleType /Bicubic /GrayImageResolution 300 /GrayImageDepth -1 /GrayImageMinDownsampleDepth 2 /GrayImageDownsampleThreshold 1.50000 /EncodeGrayImages true /GrayImageFilter /DCTEncode /AutoFilterGrayImages true /GrayImageAutoFilterStrategy /JPEG /GrayACSImageDict > /GrayImageDict > /JPEG2000GrayACSImageDict > /JPEG2000GrayImageDict > /AntiAliasMonoImages false /CropMonoImages true /MonoImageMinResolution 1200 /MonoImageMinResolutionPolicy /OK /DownsampleMonoImages true /MonoImageDownsampleType /Bicubic /MonoImageResolution 1200 /MonoImageDepth -1 /MonoImageDownsampleThreshold 1.50000 /EncodeMonoImages true /MonoImageFilter /CCITTFaxEncode /MonoImageDict > /AllowPSXObjects false /CheckCompliance [ /None ] /PDFX1aCheck false /PDFX3Check false /PDFXCompliantPDFOnly false /PDFXNoTrimBoxError true /PDFXTrimBoxToMediaBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXSetBleedBoxToMediaBox true /PDFXBleedBoxToTrimBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXOutputIntentProfile () /PDFXOutputConditionIdentifier () /PDFXOutputCondition () /PDFXRegistryName () /PDFXTrapped /False

/Description > /Namespace [ (Adobe) (Common) (1.0) ] /OtherNamespaces [ > /FormElements false /GenerateStructure true /IncludeBookmarks false /IncludeHyperlinks false /IncludeInteractive false /IncludeLayers false /IncludeProfiles true /MultimediaHandling /UseObjectSettings /Namespace [ (Adobe) (CreativeSuite) (2.0) ] /PDFXOutputIntentProfileSelector /NA /PreserveEditing true /UntaggedCMYKHandling /LeaveUntagged /UntaggedRGBHandling /LeaveUntagged /UseDocumentBleed false >> ]>> setdistillerparams> setpagedevice