e-series hmi - winmatedc.winmate.com.tw › _downloadcenter › 2016 › multi-touch ppc ›...

Please read these instructions carefully before using this product, and save this manual for future use.

E-Series HMI W07FA3S-EHT1 W10FA3S-EHH2 W15FA3S-EHA2

Quick Start Guide V1.0

Document Part Number: 9152111I101C

Copyright © Notice

No part of this document may be reproduced, copied, translated, or transmitted in

any form or by any means, electronic or mechanical, for any purpose, without the

prior written permission of the original manufacturer.

Trademark Acknowledgement

Brand and product names are trademarks or registered trademarks of their

respective owners.

Disclaimer

Winmate Inc. reserve the right to make changes, without notice, to any product,

including circuits and/or software described or contained in this manual in order to

improve design and/or performance. We assume no responsibility or liability for the

use of the described product(s) conveys no license or title under any patent,

copyright, or masks work rights to these products, and make no representations or

warranties that these products are free from patent, copyright, or mask work right

infringement, unless otherwise specified. Applications that are described in this

manual are for illustration purposes only. We make no representation or guarantee

that such application will be suitable for the specified use without further testing or

modification.

Warranty

Winmate Inc. warranty guarantees that each of its products will be free from

material and workmanship defects for a period of one year from the invoice date. If

the customer discovers a defect, we will, at his/her option, repair or replace the

defective product at no charge to the customer, provide it is returned during the

warranty period of one year, with transportation charges prepaid. The returned

product must be properly packaged in its original packaging to obtain warranty

service. If the serial number and the product shipping data differ by over 30 days,

the in-warranty service will be made according to the shipping date. In the serial

numbers the third and fourth two digits give the year of manufacture, and the fifth

digit means the month (e. g., with A for October, B for November and C for

December).

For example, the serial number 1W15Axxxxxxxx means October of year 2015.

Please read these instructions carefully before using this product, and save this manual for future use.

Contents

Getting Started 4

Unpacking 5

Accessories 5

Description Of Parts 6

E-Series HMI 7” 6

E-Series HMI 10.1” 7

E-Series HMI 15.6” 7

Dimensions 8

Dimensions 7” 8

Dimensions 10.1” 8

Dimensions 15.6” 9

Mounting 10

VESA Mount (only for 7” E-Series HMI) 10

Panel Mount 11

Connector Description 12

DC Input Connector 12

Serial Port Connector 12

LAN (RJ45) Connector 13

USB A Type Connector 13

USB OTG Connector 13

CAN BUS Connector 14

Turning ON or OFF 15

Turning ON 15

Turning OFF 15

Changing Serial Port Settings 16

Operating the HMI Device 18

Ethernet 18

Main Menu 18

Configuring Ethernet 19

Checking Ethernet Settings 20

Winmate® Home Manager 21

How to Lock Applications 21

How to Reset WHM 23

Software Developer Support 25

Winmate Software Development Kit 25

Winmate Download Center 25

Winmate File Share 25

Technical Specifications 26

HMI Device Specifications 26

4 Please read these instructions carefully before using this product, and save this guide for future use.

Getting Started Congratulations on purchasing Winmate® E-Series HMI. Winmate® continues

developing new generation of Human Machine Interfaces for Industry 4.0 and

Internet of Things (IoT). Our E-Series HMI runs on Android 4.4 / Linux operating

system that allows installing the latest applications (APPs). Thereby wide

customization possibilities are available to satisfy the needs of industrial

automation.

There is one USB 2.0 onboard to connect mouse or keyboard, USB OTG for

system updates and micro SD card for data logging, backup or data storage. 1 GB

system memory ensures stable operation of applications.

With mounting clips for panel mounting there is no need to drill holes in a fixture.

This saves you the time for mounting and guarantee aesthetic look of the wall after

the unit gets removed.

Winmate® E-Series HMI features:

Freescale® Cortex® A9 i.MX6 Dual Core 1GHz

Android/Linux Operating System (Customizable and easy to use)

Resistant to scratches P-CAP touchscreen

Fanless cooling system and Ultra-low power consumption

Front IP65 water and dust proof, rear IP22

Power over Ethernet (Data and Power connections in a single cable)

Mounting clips for Quick installation

Elegant design for room booking, access control and room information

applications

5

Unpacking Carefully remove the box and unpack your device. Please check if all the items

listed below are inside your package. If any of these items are missing or damaged

contact us immediately.

Accessories

Standard factory shipment list:

7” HMI Device Quick Start Guide

(Hardcopy) External USB cable

Power Cord AC Adapter (12V/ 50W)

Terminal Block 3 pin

*VESA Plate 75 x 75 mm

*VESA Mount Screws

Mounting Clips and Screws

7” HMI – 4 pcs 10.1” HMI – 8 pcs 15.6” HMI – 10 pcs

*VESA Mount Kit supplied only for 7” E-Series HMI.


Description Of Parts

E-Series HMI 7”

① Mini USB Debug (Linux use) ⑤ RS232/422/485

② Micro SD ⑥ CAN BUS

③ LAN/ PoE ⑦ 1 x USB 2.0

④ USB OTG ⑧ 9-24V DC in (Phoenix type)

7

E-Series HMI 10.1”





E-Series HMI 15.6”






Dimensions

Dimensions 7”

Dimensions 10.1”

9

Dimensions 15.6”

Note: this is a simplified drawing and some components are not marked in detail.


Mounting

VESA Mount (only for 7” E-Series HMI)

VESA Mount is a widely used mounting solution suitable for all kinds of

applications.

Dimensions Screw Hole Diameter

75 x 75 mm VESA M4 x 3 mm

*with customer’s bracket

Mounting Steps:

1. Screw VESA bracket to the fixture (ex. wall) with four M4 x 3 mm VESA

screws.

2. Place the device on VESA bracket.

11

Panel Mount

In addition to elegant design, panel mount solution is making the HMI unit easy to

clean and maintain. The HMI device is secured to the fixture from the rear by using

the mounting brackets included in the package.

Cutout dimension ( W x D in mm)

7” 10.1” 15.6”

172.2 x 116 260.6 x 166 390.4 x 227.3

Mounting Clips and Screws

4 pcs 8 pcs 10 pcs

Mounting Steps:


Connector Description

DC Input Connector

DC power source input is 3-pin terminal block connector.

IMPORTANT:

15.6” E-Series HMI DC IN requires maximum voltage 12V.

Support PoE (optional), requires IEEE 802.3at 25W power input.

Serial Port Connector

Use serial port connector to connect your HMI to external devices such as

mouse, modem or printer.

Serial port settings can be configured in Winmate application for Android OS.

Refer to “Configuring Serial Port Settings” of this Quick Start Guide for more detail.

Voltage

Minimum Voltage 9V Maximum Voltage 24V Maximum Current 6.6A

Pin № RS-232 (Default)

RS-422 RS-485

1 DCD TxD- D-

2 RXD TxD+ D+

3 TXD RxD+ NC

4 DTR RxD- NC

5 GND GND GND

6 DSR NC NC

7 RTS NC NC

8 CTS NC NC

9 RI NC NC

13

LAN (RJ45) Connector

The E-Series HMI supports one 10/100/1000 Mbps Ethernet interface for connecting to the internet.

USB A Type Connector

Use USB A Type (USB2.0) connector to connect your HMI device to other

USB2.0 compatible devices.

USB OTG Connector

Use USB OTG connector to connect the HMI device to other external devices.

Use USB OTG cable to install software on the HMI device.

Refer to the E-Series HMI User Manual for more details on how to install software.

Pin № Name Pin № Name

1 TX1+ 2 TX1-

3 TX2+ 4 TX2-

5 TX3+ 6 TX3-

7 TX4+ 8 TX4-


1 +5V 2 USB_D-

3 USB_D+ 4 GND

5 STDA_SSRX- 6 STDA_SSRX+

7 GND_DRAIN 8 STDA_SSTX-

9 STDA_SSTX+ 10 +5V

11 USB_D- 12 USB_D+

13 GND


1 +5V 2 USB_OTG_D-

3 USB_OTG_D+ 4 USB_OTG_ID

5 GND


CAN BUS Connector

Use CAN BUS connector to connect your HMI device to in-vehicle system.

*PIN9 default is NC

.


1 GND 2 CAN_L

3 GND 4 NC

5 NC 6 NC

7 CAN_H 8 GND

9* +5V/NC

15

Turning ON or OFF

Turning ON

Follow the following steps to turn on your HMI device:

1. Connect a 3-pin terminal block to the HMI connector.

2. Connect the other side of the terminal block to the AC adapter.

3. Connect the AC adapter to the power cord.

4. Plug the power cord to the AC outlet and the device will turn on automatically.

CAUTION Use only the AC adapter included in your package (Rating: Output 4.2 A). Using other AC adapters may damage the device.

Turning OFF

Disconnect the power cord from the HMI device to completely turn off the device.

ALTERNATING CURRENT This product must be grounded. Use only a grounded AC outlet. Install the additional PE ground wire if the local installation regulations require it.


Changing Serial Port Settings Serial port can be configured for RS-232, RS-422 or RS-485. Winmate® provides

serial port settings application for Android OS.

To configure serial port settings follow the instructions below:

Step 1 Settings > Accessibility

Step 2 Accessibility > Comport-Setting

17

Step 3 Comport-Setting > Comport 1/ Comport 2/ Comport 3

* Select Comport 1/ Comport 2/ Comport 3 that you want to configure.

Step 4 Comport 1 > RS232/RS422/RS485

* Configure Comport 1 settings


Operating the HMI Device This section explains how to adjust main system settings in Android 4.4.

Ethernet

Main Menu

Use Android application to connect Ethernet.

Step 1 Connect Ethernet Cable to the HMI device.

Step 2 Go to APPS. Open Ethernet application.

Step 3 Ethernet APP main menu appears

Setting Description

Check Ethernet Check Ethernet connection parameters: IP mode, IP

address, DNS address and others

Configure Ethernet Enable Ethernet connection and configure its such as

connection type

Advanced Settings Configure advanced parameters of the Ethernet

19

Configuring Ethernet

Go to Apps > Ethernet > Configure Ethernet

*Ethernet OFF is set by default. Swipe Ethernet ON to activate Ethernet

connection.

Connection Type

Setting Description

DHCP (default) The device automatically capture IP-address from the

router

Static IP Allows to manually set up IP-address, DNS, Network and

Gateway


Checking Ethernet Settings

Go to APPS > Ethernet > Check Ethernet

Ethernet settings menu appears on the top right side of the desktop.

For a more detailed Android 4.4 user guide, follow the download path below:

http://static.googleusercontent.com/media/www.google.com/en/us/help/hc/images/android/androi

d_ug_42/Android-Quick-Start-Guide.pdf

http://static.googleusercontent.com/media/www.google.com/en/us/help/hc/images/android/android_ug_42/Android-Quick-Start-Guide.pdf

http://static.googleusercontent.com/media/www.google.com/en/us/help/hc/images/android/android_ug_42/Android-Quick-Start-Guide.pdf

21

Winmate® Home Manager Winmate ® E-Series HMI comes with preinstalled APP named Winmate® Home

Manager (WHM) which let the device manager to lock the launcher then the user

can only use one application assigned by the device manager.

How to Lock Applications

Step 1 In the main APPS window, select the Home Manager APP and tap

it to open.

Setting Description

Home Manager Select the application you want to run up automatically after

booting.

Password

Manager

Enter to set the WHM password (Default is “0000”).

Step 2 Go to “Application Selector”, and choose the app which you want to

run up automatically after booting.


Step 3 Go back to “Home Selector” and press “Clear and Reset Default

Home”.

23

Step 4 Select “Restrict Home” and “Always”, and then restart the computer to

enable these settings.

The system will automatically start the application which you selected and lock it.

Whatever you press home key or back key; the system will go back to the same

application which you have selected.

How to Reset WHM

Step 1 If you want to reset the home manager, pull down the left side to open

the status bar and open HomeManager service.


Step 2 System will request the password to login.

Default password is “0000”.

Step 3 Restart the system and you will go back to the normal Launcher.

25

Software Developer Support

Winmate Software Development Kit

Winmate® provides Software Development Kit (SDK). The table below lists SDK

provided by Winmate for E-Series HMI with Freescale® Cortex® A9 i.MX6 Dual

Core processor:

Item Driver Description

1 Android Driver USB Driver

2 Android Driver USB OTG Driver

3 SDK Android SDK

4 SDK Linux SDK

5 Guide Download OS Image Tool

To find the Drivers and SDK, please refer to the Driver CD that comes in the

package or contact us. Also, you can download drivers from Winmate Download

Center or Winmate File Share.

Winmate Download Center

Go to http://www.winmate.com.tw/ > Support > Download Center > Multi-Touch PPC > E-

Series HMI > Development Kit / Drivers

Or follow the link: http://www.winmate.com/DownCenter/DownLoadCenter.asp?DownType=3018

Winmate File Share

Go to http://www.winmate.com.tw/ > Support > Partner Portal > Public Documents > Panel PC > Multi-Touch HMI > E-Series HMI > Development Kit / Drivers

Or follow the link: https://winmate.box.com/v/E-Series-HMI

http://www.winmate.com.tw/

http://www.winmate.com/DownCenter/DownLoadCenter.asp?DownType=3018


https://winmate.box.com/v/E-Series-HMI


Technical Specifications

HMI Device Specifications

Model Name

W07FA3S-EHT1 W10FA3S-EHH2 W15FA3S-EHA2

Display:

Size/ Type 7” TFT 10.1” TFT 15.6" TFT

Resolution 1024x600 1280 x 800 1366 x 768

Brightness 320cd/m (typ.) 300 cd/m (typ.) 400 cd/m (typ.)

Contrast Ratio 500 : 1 (typ.) 800:1 (typ.) 500 : 1 (typ.

Viewing Angle -70~70(H);-50~60(V) -70~70 (H);50~60(V) -70~70(H);-50~60(V)

Max Colors 16.7M (8bit) 262K (6bit) 16.7M (8bit)

Touch Projective-Capacitive Touch

Mechanical Specifications:

Dimensions, mm (W x H x D)

184.8 x 128.6 x 50.2 293.6 x 199.2 x 62.3 421 x 260.6 x 65.5

Mounting 4 x Mounting clips VESA 75x75mm

8 x Mounting clips VESA 75x75mm

10 x Mounting clips VESA 75x75mm

Cooling Fanless design

System:

Processor Freescale® Cortex® A9 i.MX6 Dual Core 1GHz

System Memory 1GB LPDDR3

Storage Onboard 16GB eMMC /Micro SD card

OS Android 4.4 (Default) Linux Kernel 3.0.35,QT 5.4 Browser (Optional)

Input / Output

USB Ports 1 x USB 2.0 host, 1 x USB OTG

COM Port 1 x RS232 (Optional 422/485)

CAN BUS 1 x CANBUS

Ethernet 1 x RJ45, 10/100/1000 LAN (Optional PoE function)

SD Slot 1 x Micro SD Card Slot

Debug 1 x Mini USB to Debug

Power Specifications:

Power Input 9~24V DC in 9~24V DC in 12V DC in

Power Over Ethernet Support PoE (optional), requires IEEE 802.3at 25W power input (Recommended to use without other power-consuming devices)

Environment Considerations :

Operating Temp. -25°C to +65°C

Operating Humidity 10 ~ 90% (non-condensing)

Winmate Inc. 9F, No.111-6, Shing-De Rd., San-Chung District, Taipei 241, Taiwan, R.O.C Tel: 886-2-8511-0288 Fax: 886-2-8511-0211 Email: [email protected] Official website: www.winmate.com
