Lecture -10: BIpolar Junction Transistor

Biploar transistor:

A transistor is basically a Si on Ge crystal containing three separate regions. It can be either NPN or PNP type fig. 1. The middle region is called the base and the outer two regions are called emitter and the collector. The outer layers although they are of same type but their functions cannot be changed. They have different physical and electrical properties.

In most transistors, emitter is heavily doped. Its job is to emit or inject electrons into the base. These bases are lightly doped and very thin, it passes most of the emitter-injected electrons on to the collector. The doping level of collector is intermediate between the heavy doping of emitter and the light doping of the base.

The collector is so named because it collects electrons from base. The collector is the largest of the three regions; it must dissipate more heat than the emitter or base. The transistor has two junctions. One between emitter and the base and other between the base and the collector. Because of this the transistor is similar to two diodes, one emitter diode and other collector base diode.

 

Fig .1

When transistor is made, the diffusion of free electrons across the junction produces two depletion layers. For each of these depletion layers, the barrier potential is 0.7 V for Si transistor and 0.3 V for Ge transistor.

The depletion layers do not have the same width, because different regions have different doping levels. The more heavily doped a region is, the greater the concentration of ions near the

junction. This means the depletion layer penetrates more deeply into the base and slightly into emitter. Similarly, it penetration more into collector. The thickness of collector depletion layer is large while the base depletion layer is small as shown in fig. 2.

Fig. 2

If both the junctions are forward biased using two d.c sources, as shown in fig. 3a. free electrons (majority carriers) enter the emitter and collector of the transistor, joins at the base and come out of the base. Because both the diodes are forward biased, the emitter and collector currents are large.

Fig. 3a Fig. 3b

If both the junction are reverse biased as shown in fig. 3b, then small currents flows through both junctions only due to thermally produced minority carriers and surface leakage. Thermally produced carriers are temperature dependent it approximately doubles for every 10 degree celsius rise in ambient temperature. The surface leakage current increases with voltage.

When the emitter diode is forward biased and collector diode is reverse biased as shown in fig. 4 then one expect large emitter current and small collector current but collector current is almost as large as emitter current.

Fig. 4

When emitter diodes forward biased and the applied voltage is more than 0.7 V (barrier potential) then larger number of majority carriers (electrons in n-type) diffuse across the junction.

Once the electrons are injected by the emitter enter into the base, they become minority carriers. These electrons do not have separate identities from those, which are thermally generated, in the base region itself. The base is made very thin and is very lightly doped. Because of this only few electrons traveling from the emitter to base region recombine with holes. This gives rise to recombination current. The rest of the electrons exist for more time. Since the collector diode is reverse biased, (n is connected to positive supply) therefore most of the electrons are pushed into collector layer. These collector elections can then flow into the external collector lead.

Thus, there is a steady stream of electrons leaving the negative source terminal and entering the emitter region. The VEB forward bias forces these emitter electrons to enter the base region. The thin and lightly doped base gives almost all those electrons enough lifetime to diffuse into the depletion layer. The depletion layer field pushes a steady stream of electron into the collector region. These electrons leave the collector and flow into the positive terminal of the voltage source. In most transistor, more than 95% of the emitter injected electrons flow to the collector, less than 5% fall into base holes and flow out the external base lead. But the collector current is less than emitter current.

Relation between different currents in a transistor:

The total current flowing into the transistor must be equal to the total current flowing out of it. Hence, the emitter current IE is equal to the sum of the collector (IC ) and base current (IB). That is,

IE = IC + IB

The currents directions are positive directions. The total collector current IC is made up of two components.

1. The fraction of emitter (electron) current which reaches the collector ( adc IE )

2. The normal reverse leakage current ICO

adc is known as large signal current gain or dc alpha. It is always positive. Since collector current is almost equal to the IE therefore αdc IE varies from 0.9 to 0.98. Usually, the reverse leakage current is very small compared to the total collector current.

NOTE: The forward bias on the emitter diode controls the number of free electrons infected into the base. The larger (VBE) forward voltage, the greater the number of injected electrons. The reverse bias on the collector diode has little influence on the number of electrons that enter the collector. Increasing VCB does not change the number of free electrons arriving at the collector junction layer.

The symbol of npn and pnp transistors are shown in fig. 5.

Fig. 5

Breakdown Voltages:

Since the two halves of a transistor are diodes, two much reverse voltage on either diode can cause breakdown. The breakdown voltage depends on the width of the depletion layer and the doping levels. Because of the heavy doping level, the emitter diode has a low breakdown voltage approximately 5 to 30 V. The collector diode is less heavily doped so its breakdown voltage is higher around 20 to 300 V.

Lecture - 11: Common Base Configuration

The Common Base Configuration :

If the base is common to the input and output circuits, it is know as common base configuration as shown in fig. 1.

Fig. 1

For a pnp transistor the largest current components are due to holes. Holes flow from emitter to collector and few holes flow down towards ground out of the base terminal. The current directions are shown in fig. 1.

(IE = IC + IB ).

For a forward biased junction, VEB is positive and for a reverse biased junction VCB is negative. The complete transistor can be described by the following two relations, which give the input voltage VEB and output current IC in terms of the output voltage (VCB) and input current IE.

VEB = f1(VCB, IE)

IC= f2(VCB, IE) 

The output characteristic:

The collector current IC is completely determined by the input current IE and the VCB voltage. The relationship is given in fig. 2. It is a plot of IC versus VCB, with emitter current IE as parameter. The curves are known as the output or collector or static characteristics. The transistor consists of two diodes placed in series back to back (with two cathodes connected together). The complete characteristic can be divided in three regions.

Figure 7.2

(1). Active region:

In this region the collector diode is reverse biased and the emitter diode is forward biased. Consider first that the emitter current is zero. Then the collector current is small and equals the reverse saturation current ICO of the collector junction considered as a diode.

If the forward current IB is increased, then a fraction of IE ie. adcIE will reach the collector. In the active region, the collector current is essentially independent of collector voltage and depends only upon the emitter current. Because adc is, less than one but almost equal to unity, the magnitude of the collector current is slightly less that of emitter current. The collector current is almost constant and work as a current source.

The collector current slightly increases with voltage. This is due to early effect. At higher voltage collector gathers in a few more electrons. This reduces the base current. The difference is so small, that it is usually neglected. If the collector voltage is increased, then space charge width increases; this decreased the effective base width. Then there is less chance for recombination within the base region.

(2). Saturation region:

The region to the left of the ordinate VCB = 0, and above the IE = 0, characteristic in which both emitter and collector junction are forward biased, is called saturation region.

When collector diode is forward biased, there is large change in collector current with small changes in collector voltage. A forward bias means, that p is made positive with respect to n, there is a flow of holes from p to n. This changes the collector current direction. If diode is sufficiently forward biased the current changes rapidly. It does not depend upon emitter current.

(3). Cut off region:

The region below IE = 0 and to the right of VCB for which emitter and collector junctions are both reversed biased is referred to cutoff region. The characteristics IE = 0, is similar to other characteristics but not coincident with horizontal axis. The collector current is same as ICO. ICBO is frequently used for ICO. It means collector to base current with emitter open. This is also temperature dependent.

GOTO >> 1 || 2 || 3 || Home

The Input Characteristic:

In the active region the input diode is forward biased, therefore, input characteristic is simply the forward biased characteristic of the emitter to base diode for various collector voltages. fig. 3. Below cut in voltage (0.7 or 0.3) the emitter current is very small. The curve with the collector open represents the forward biased emitter diode. Because of the early effect the emitter current increases for same VEB. (The diode becomes better diode).

When the collector is shorted to the base, the emitter current increases for a given VEB since the collector now removes minority carriers from the base, and hence base can attract more holes from the emitter. This mean that the curve VCB= 0, is shifted from the character when VCB = open.

Fig. 3

 

Equivalent circuit of a transistor: (Common Base)

 

 

 

 

Fig. 4

  

 

Lecture -12: Common Base Amplifier

Common Base Amplifier:

The common base amplifier circuit is shown in Fig. 1. The VEE source forward biases the emitter diode and VCC source reverse biased collector diode. The ac source vin is connected to emitter through a coupling capacitor so that it blocks dc. This ac voltage produces small fluctuation in currents and voltages. The load resistance RL is also connected to collector through coupling capacitor so the fluctuation in collector base voltage will be observed across RL.

The dc equivalent circuit is obtained by reducing all ac sources to zero and opening all capacitors. The dc collector current is same as IE and VCB

is given by

VCB = VCC - IC RC.

Fig. 1

These current and voltage fix the Q point. The ac equivalent circuit is obtained by reducing all dc sources to zero and shorting all coupling capacitors. r'e represents the ac resistance of the diode as shown in Fig. 2.

In an ideal transistor, adc= 1. This means all emitter electrons entering the base region go on to the collector. Therefore, collector current equals emitter current. For transistor action, emitter diode acts like a forward bias diode and collector diode acts like a current source. The equivalent circuits of npn and pnp transistors are shown in fig. 4. The current source arrow points for conventional current. The current source is controlled by emitter current.

Fig. 2

Fig. 3, shows the diode curve relating IE and VBE. In the absence of ac signal, the transistor operates at Q point (point of intersection of load line and input characteristic). When the ac signal is applied, the emitter current and voltage also change. If the signal is small, the operating point swings sinusoidally about Q point (A to B).

Fig .3

If the ac signal is small, the points A and B are close to Q, and arc A B can be approximated by a straight line and diode appears to be a resistance given by

If the input signal is small, input voltage and current will be sinusoidal but if the input voltage is large then current will no longer be sinusoidal because of the non linearity of diode curve. The emitter current is elongated on the positive half cycle and compressed on negative half cycle. Therefore the output will also be distorted.

r'e is the ratio of ΔVBE and Δ IE and its value depends upon the location of Q. Higher up the Q point small will be the value of r' e because the same change in VBE produces large change in IE. The slope of the curve at Q determines the value of r'e. From calculation it can be proved that.

r'e = 25mV / IE

Proof:

In general, the current through a diode is given by

Where q is he charge on electron, V is the drop across diode, T is the temperature and K is a constant.

On differentiating w.r.t V, we get,

The value of (q / KT) at 25°C is approximately 40.

Therefore,

or,      

To a close approximation the small changes in collector current equal the small changes in emitter current. In the ac equivalent circuit, the current ‘iC' is shown upward because if ‘ie' increases, then ‘iC' also increases in the same direction.

Voltage gain:

Since the ac input voltage source is connected across r'e. Therefore, the ac emitter current is given by

ie = Vin / r'e

or,        Vin = ie r'e

The output voltage is given by Vout = ic (RC || RL)

Under open circuit condition vout = ic Rc

Example-1

Find the voltage gain and output of the amplifier shown in fig. 4, if input voltage is 1.5mV.

Fig. 4

Solution:

The emitter dc current I E is given by

Therefore, emitter ac resistance =

or,           AV= 56.6

and, Vout = 1.5 x 56.6 = 84.9 mV

Example-2

Repeat example-1 if ac source has resistance R s = 100 W .

Solution:

The ac equivalent circuit with ac source resistance is shown in fig. 5.

Fig. 5

The emitter ac current is given by

or,              

Therefore, voltage gain of the amplifier =

    

and,                       Vout = 1.5 x 8.71 =13.1 mV

Lecture -13: Common Emitter Configuration

Common Emitter Curves:

The common emitter configuration of BJT is shown in fig. 1.

Fig. 1

In C.E. configuration the emitter is made common to the input and output. It is also referred to as grounded emitter configuration. It is most commonly used configuration. In this, base current and output voltages are taken as impendent parameters and input voltage and output current as dependent parameters

VBE = f1 ( IB, VCE )

IC = f2( IB, VCE )

Input Characteristic:

The curve between IB and VBE for different values of VCE are shown in fig. 2. Since the base emitter junction of a transistor is a diode, therefore the characteristic is similar to diode one. With higher values of VCE collector gathers slightly more electrons and therefore base current reduces. Normally this effect is neglected. (Early effect). When collector is shorted with emitter then the input characteristic is the characteristic of a forward biased diode when VBE is zero and IB is also zero.

Fig. 2

Output Characteristic:

The output characteristic is the curve between VCE and IC for various values of IB. For fixed value of IB and is shown in fig. 3. For fixed value of IB, IC is not varying much dependent on VCE but slopes are greater than CE characteristic. The output characteristics can again be divided into three parts.

Fig. 3

(1) Active Region:

In this region collector junction is reverse biased and emitter junction is forward biased. It is the area to the right of VCE = 0.5 V and above IB= 0. In this region transistor current responds most sensitively to IB. If transistor is to be used as an amplifier, it must operate in this region.

If adc is truly constant then IC would be independent of VCE. But because of early effect, adc increases by 0.1% (0.001) e.g. from 0.995 to 0.996 as VCE increases from a few volts to 10V. Then bdc increases from 0.995 / (1-0.995) = 200 to 0.996 / (1-0.996) = 250 or about 25%. This shows that small change in a reflects large change in b. Therefore the curves are subjected to large variations for the same type of transistors.

(2) Cut Off:

Cut off in a transistor is given by IB = 0, IC= ICO. A transistor is not at cut off if the base current is simply reduced to zero (open circuited) under this condition,

IC = IE= ICO / ( 1-αdc) = ICEO

The actual collector current with base open is designated as ICEO. Since even in the neighborhood of cut off, a dc may be as large as 0.9 for Ge, then IC=10 ICO(approximately), at zero base current. Accordingly in order to cut off transistor it is not enough to reduce IB to zero, but it is necessary to reverse bias the emitter junction slightly. It is found that reverse voltage of 0.1 V is sufficient for cut off a transistor. In Si, the a dc is very nearly equal to zero, therefore, IC = ICO. Hence even with IB= 0, IC= IE= ICO so that transistor is very close to cut off.

In summary, cut off means IE = 0, IC = ICO, IB = -IC = -ICO , and VBE is a reverse voltage whose magnitude is of the order of 0.1 V for Ge and 0 V for Si.

Reverse Collector Saturation Current ICBO:

When in a physical transistor emitter current is reduced to zero, then the collector current is known as ICBO (approximately equal to ICO). Reverse collector saturation current ICBO also varies with temperature, avalanche multiplication and variability from sample to sample. Consider the circuit shown in fig. 4. VBB is the reverse voltage applied to reduce the emitter current to zero.

IE = 0,          IB = -ICBO

If we require, VBE = - 0.1 V

Then  - VBB + ICBO RB < - 0.1 V

Fig. 4

If RB = 100 K, ICBO = 100 m A, Then VBB must be 10.1 Volts. Hence transistor must be capable to withstand this reverse voltage before breakdown voltage exceeds.

(3).Saturation Region:

In this region both the diodes are forward biased by at least cut in voltage. Since the voltage VBE and VBC across a forward is approximately 0.7 V therefore, VCE = VCB + VBE = - VBC + VBE is also few tenths of volts. Hence saturation region is very close to zero voltage axis, where all the current rapidly reduces to zero. In this region the transistor collector current is approximately given by VCC / R C and independent of base current. Normal transistor action is last and it acts like a small ohmic resistance.

 

Large Signal Current Gain βdc :-

The ratio Ic / IB is defined as transfer ratio or large signal current gain bdc

Where IC is the collector current and IB is the base current. The bdc is an indication if how well the transistor works. The typical value of bdc varies from 50 to 300.

In terms of h parameters, b dc is known as dc current gain and in designated hfE ( b dc = hfE). Knowing the maximum collector current and bdc the minimum base current can be found which will be needed to saturate the transistor.

This expression of bdc is defined neglecting reverse leakage current (ICO).

Taking reverse leakage current (ICO) into account, the expression for the bdc can be obtained as follows:

bdc in terms of adc is given by

Since, ICO = ICBO

Cut off of a transistor means IE = 0, then IC= ICBO and IB = - ICBO. Therefore, the above expression bdc gives the collector current increment to the base current change form cut off to IB and hence it represents the large signal current gain of all common emitter transistor.

Lecture - 14: Biasing Techniques for CE Amplifiers

Biasing Circuit Techniques or Locating the Q - Point:

Fixed Bias or Base Bias:

In order for a transistor to amplify, it has to be properly biased. This means forward biasing the base emitter junction and reverse biasing collector base junction. For linear amplification, the

transistor should operate in active region ( If IE increases, IC increases, VCE decreases proportionally).

The source VBB, through a current limit resistor RB forward biases the emitter diode and VCC through resistor RC (load resistance) reverse biases the collector junction as shown in fig. 1.

Fig. 1

The dc base current through RB is given by

IB = (VBB - VBE) / RB      

or          VBE = VBB - IB RB

Normally VBE is taken 0.7V or 0.3V. If exact voltage is required, then the input characteristic ( IB

vs VBE) of the transistor should be used to solve the above equation. The load line for the input circuit is drawn on input characteristic. The two points of the load line can be obtained as given below

For   IB = 0,          VBE = VBB.

and      For    VBE = 0,         IB = VBB/ RB.

The intersection of this line with input characteristic gives the operating point Q as shown in fig. 2. If an ac signal is connected to the base of the transistor, then variation in VBE is about Q - point. This gives variation in IB and hence IC.

Fig. 2

In the output circuit, the load equation can be written as

VCE = VCC- IC RC

This equation involves two unknown VCE and IC and therefore can not be solved. To solve this equation output characteristic ( ICvs VCE) is used.

The load equation is the equation of a straight line and given by two points:

IC= 0,         VCE = VCC

&            VCE = 0,        IC= VCC / RC

The intersection of this line which is also called dc load line and the characteristic gives the operating point Q as shown in fig. 3.

Fig. 3

The point at which the load line intersects with IB = 0 characteristic is known as cut off point. At this point base current is zero and collector current is almost negligibly small. At cut off the emitter diode comes out of forward bias and normal transistor action is lost. To a close approximation.

VCE ( cut off) » VCC (approximately).

The intersection of the load line and IB = IB(max) characteristic is known as saturation point . At this point IB= IB(max), IC= IC(sat). At this point collector diodes comes out of reverse bias and again transistor action is lost. To a close approximation,

IC(sat) » VCC / RC(approximately ).

The IB(sat) is the minimum current required to operate the transistor in saturation region. If the IB is less than IB (sat), the transistor will operate in active region. If IB > IB (sat) it always operates in saturation region.

If the transistor operates at saturation or cut off points and no where else then it is operating as a switch is shown in fig. 4.

Fig. 4

VBB = IB RB+ VBE

IB = (VBB – VBE ) / RB

If IB> IB(sat), then it operates at saturation, If IB = 0, then it operates at cut off.

If a transistor is operating as an amplifier then Q point must be selected carefully. Although we can select the operating point any where in the active region by choosing different values of RB & RC but the various transistor ratings such as maximum collector dissipation PC(max) maximum collector voltage VC(max) and IC(max) & VBE(max) limit the operating range.

Once the Q point is established an ac input is connected. Due to this the ac source the base current varies. As a result of this collector current and collector voltage also varies and the amplified output is obtained.

If the Q-point is not selected properly then the output waveform will not be exactly the input waveform. i.e. It may be clipped from one side or both sides or it may be distorted one.

Example-1

Find the transistor current in the circuit shown in fig. 5, if ICO= 20nA, β =100.

Solution:

For the base circuit, 5 = 200 x IB + 0.7

Therefore, 

Since ICO << IB, therefore, IC = β IB = 2.15 mA

From the collector circuit, VCE = 10 - 3 x 2.15 = 3.55 V

Since, VCE = VCB + VBE

Thus, VCB = 3.55 - 0.7 = 2.55 V

Therefore, collector junction is reverse biased and transistor is operating in its active region.

Fig. 5

Example - 2

If a resistor of 2K is connected in series with emitter in the circuit as shown in fig. 6, find the currents. Given ICO= 20 nA, β =100.

Solution:

IE = IB + IC = IB + 100 IB = 101 IB

For the base circuit, 5 = 200 x IB + 0.7 + 2k x 101 IB

Therefore,   Fig. 6

Since ICO << IB, therefore, IC = βIB = 1.07 mA

From the collector circuit, VCB = 10 - 3 x 1.07 - 0.7 - 2 x 101 x 0.0107 = 3.93 V

Therefore collector junction is reverse biased and transistor is operating in its active region.

Example - 3

Repeat the example-1 if RB is replaced by 50k.

Solution:

The circuit is shown in fig. 7.

Since the base resistance is reduced, the base current must have increased and there is a possibility that the transistor has entered into saturation region.

Assuming transistor is operating in its saturation region,

VBE (sat)= 0.8 V and VCE (sat) = 0.2V

Therefore,

and           

The minimum base current required for operating the transistor in saturation region is

Since IB > IB(min), therefore, transistor is operating in its saturation region.

Fig. 7

Example - 4

Repeat the example-2 if RB is replaced by 50k.

Solution:

The circuit is shown in fig. 8.

Since the base resistance is reduced, the base current must have increased and there is a possibility that the transistor has entered into saturation region.

Assuming transistor is operating in its saturation region,

Solving these equations, we get,

IC = 1.96mA and IB = 0.0035mA

The minimum base current required for operating the transistor in saturation region is

Since I B < I B(min) , therefore, transistor is operating in its active region and not in saturation. The base and the collector currents can be recalculated assuming the transistor to be in active region.

For the base circuit, 5 = 50 x IB + 0.7 + 2k x 101 IB

Therefore,

    IC = 1.71mA

From the collector circuit, VCB = 10 - 3 x 1.71 - 0.7 - 2 x 101 x 0.0171 = 0.716 V

Fig. 8

Lecture - 15: Stability of Operating Point

Let us consider three operating points of transistor operating in common emitter amplifier.

1. Near cut off

2. Near saturation 3. In the middle of active region

If the operating point is selected near the cutoff region, the output is clipped in negative half cycle as shown in fig. 1.

Fig. 1

If the operating point is selected near saturation region, then the output is clipped in positive cycle as shown in fig. 2.

Fig. 2 Fig. 3

If the operating point is selected in the middle of active region, then there is no clipping and the output follows input faithfully as shown in fig. 3. If input is large then clipping at both sides will take place. The first circuit for biasing the transistor is CE configuration is fixed bias.

In biasing circuit shown in fig. 4(a), two different power supplies are required. To avoid the use of two supplies the base resistance RB is connected to VCC as shown in fig. 4(b).

Fig. 4(a) Fig. 4(b)

Now VCC is still forward biasing emitter diode. In this circuit Q point is very unstable. The base resistance RB is selected by noting the required base current IB for operating point Q.

IB = (VCC – VBE ) / RB

Voltage across base emitter junction is approximately 0.7 V. Since VCC is usually very high

i.e. IB = VCC/ RB

Since IB is constant therefore it is called fixed bias circuit.

Stability of quiescent operating point:

Let us assume that the transistor is replaced by an other transistor of same type. The bdc of the two transistors of same type may not be same. Therefore, if bdc increases then for same IB, output characteristic shifts upward. If bdc decreases, the output characteristic shifts downward. Since IB is maintained constant, therefore the operating point shifts from Q to Q1 as shown in fig. 5. The new operating point may be completely unsatisfactory.

Therefore, to maintain operating point stable, IB should be allowed to change so as to maintain VCE & IC constant as bdc changes.

Fig. 5

A second cause for bias instability is a variation in temperature. The reverse saturation current changes with temperature. Specifically, ICO doubles for every 10oC rise in temperature. The collector current IC causes the collector junction temperature to rise, which in turn increases ICO. As a result of this growth ICO, IC will increase ( bdc IB + (1+ b dc ) ICO ) and so on. It may be possible that this process goes on and the ratings of the transistors are exceeded. This increase in IC changes the characteristic and hence the operating point.

Stability Factor:

The operating point can be made stable by keeping IC and VCE constant. There are two techniques to make Q point stable.

1. stabilization techniques2. compensation techniques

In first, resistor biasing circuits are used which allow IB to vary so as to keep IC relatively constant with variations in bdc , ICO and VBE.

In second, temperature sensitive devices such as diodes, transistors are used which provide compensating voltages and currents to maintain the operating point constant.

To compare different biasing circuits, stability factor S is defined as the rate of change of collector current with respect to the ICO, keeping bdc and VCE constant

S = ¶ IC / ¶ ICO

If S is large, then circuit is thermally instable. S cannot be less than unity. The other stability factors are, ¶ IC / ¶ bdc and ¶ IC / ¶ VBE. The bias circuit, which provide stability with ICO, also show stability even if b and VBEchanges.

IC = b dcIB + (I + b dc ) ICO

Differentiating with respect to IC,

In fixed bias circuit, IB & IC are independent. Therefore and S = 1 + bdc. If b dc=100, S = 101, which means ICincreases 101 times as fast as ICO. Such a large change definitely operate the transistor in saturation

. Lecture - 16: Biasing Techniques

 

Emitter Feedback Bias:

Fig. 1, shows the emitter feedback bias circuit. In this circuit, the voltage across resistor RE is used to offset the changes in bdc. If bdc increases, the collector current increases. This increases the emitter voltage which decrease the voltage across base resistor and reduces base current. The reduced base current result in less collector current, which partially offsets the original increase in bdc. The feedback term is used because output current ( IC) produces a change in input current ( IB ). RE is common in input and output circuits.

Fig. 1

In this case

Vcc=IBRB +vBE+IERE

Since IE = IC + IB

Therefore,

In this case, S is less compared to fixed bias circuit. Thus the stability of the Q point is better.

Further,

If IC is to be made insensitive to βdc than

RE cannot be made large enough to swamp out the effects of βdc without saturating the transistor.

Collector Feedback Bias:

In this case, the base resistor is returned back to collector as shown in fig . 2 . If temperature increases. βdc increases. This produces more collectors current. As IC increases, collector emitter voltage decreases. It means less voltage across RB and causes a decrease in base current this decreasing IC, and compensating the effect of bdc.

Fig. 2

In this circuit, the voltage equation is given by

Circuit is stiff sensitive to changes in βdc. The advantage is only two resistors are used.

Then,

Therefore,

It is better as compared to fixed bias circuit.

Further,

Circuit is still sensitive to changes in βdc. The advantage is only two resistors are used.

Voltage Divider Bias:

If the load resistance RC is very small, e.g. in a transformer coupled circuit, then there is no improvement in stabilization in the collector to base bias circuit over fixed bias circuit. A circuit which can be used even if there is no dc resistance in series with the collector, is the voltage divider bias or self bias. fig. 3.

The current in the resistance RE in the emitter lead causes a voltage drop which is in the direction to reverse bias the emitter junction. Since this junction must be forward biased, the base voltage is obtained from the supply through R1, R2 network. If Rb = R1 || R2 equivalent resistance is very – very small, then VBE voltage is independent of ICO and ¶ IC / ¶ ICO ® 0. For best stability R1 & R2 must be kept small.

Fig. 3

If IC tends to increase, because of ICO, then the current in RC increases, hence base current is decreased because of more reverse biasing and it reduces IC .

To analysis this circuit, the base circuit is replaced by its thevenin's equivalent as shown in fig. 4.

Fig. 4

Thevenin's voltage is

Rb is the effective resistance seen back from the base terminal.

If VBE is considered to be independent of IC, then

The smaller the value of Rb, the better is the stabilization but S cannot be reduced be unity.

Hence IC always increases more than ICO. If Rb is reduced, then current drawn from the supply increases. Also if RE is increased then to operate at same Q-point, the magnitude of VCC must be increased. In both the cases the power loss increased and reduced h.

In order to avoid the loss of ac signal because of the feedback caused by RE, this resistance is often by passed by a large capacitance (> 10 m F) so that its reactance at the frequency under consideration is very small.

Emitter Bias:

Fig. 5, shown the emitter bias circuit. The circuit gets this name because the negative supply VEE is used to forward bias the emitter junction through resistor RE. VCC still reverse biases collector junction. This also gives the same stability as voltage divider circuit but it is used only if split supply is available.

Fig. 5

In this circuit, the voltage equation is given by

Lecture - 17: Biasing Techniques

Example-1

Determine the Q-point for the CE amplifier given in fig. 1, if R1 = 1.5K W and Rs = 7K W . A 2N3904 transistor is used with β = 180, RE = 100W and RC = Rload = 1K W . Also determine the Pout(ac) and the dc power delivered to the circuit by the source.

Fig. 1

Solution:

We first obtain the Thevenin equivalent.

and

Note that this is not a desirable Q-point location since VBB is very close to VBE. Variation in VBE therefore significantly change IC.We find Rac = RC || Rload= 500 W and Rdc = RC + RE =1.1KW. The value of VCE representing the quiescent value associated with ICQ is found as follows,

Then

Since the Q-point is on the lower half of the ac load line, the maximum possible symmetrical output voltage swing is

The ac power output can be calculated as

The power drawn from the dc source is given by

The power loss in the transistor is given by

The Q-point in this example is not in the middle of the load line so that output swing is not as great as possible. However, if the input signal is small and maximum output is not required, a small IC can be used to reduce the power dissipated in the circuit.

Moving Ground Around:

Ground is a reference point that can be moved around. e.g. consider a collector feedback bias circuit. The various stages of moving ground are shown in fig. 2.

Fig. 2

Biasing a pnp Transistor:

The biasing of pnp transistor is done similar to npn transistor except that supply is of opposite polarity The various biasing circuits of pnp transistor are shown in fig. 3.

Fig. 3

Example 2:

For the circuit shown in fig. 4, calculate IC and VCE

Solution:

Fig. 4 Lecture - 18: Small Signal CE Amplifiers

Small Signal CE Amplifiers:

CE amplifiers are very popular to amplify the small signal ac. After a transistor has been biased with a Q point near the middle of a dc load line, ac source can be coupled to the base. This produces fluctuations in the base current and hence in the collector current of the same shape and frequency. The output will be enlarged sine wave of same frequency.

The amplifier is called linear if it does not change the wave shape of the signal. As long as the input signal is small, the transistor will use only a small part of the load line and the operation will be linear.

On the other hand, if the input signal is too large. The fluctuations along the load line will drive the transistor into either saturation or cut off. This clips the peaks of the input and the amplifier is no longer linear.

The CE amplifier configuration is shown in fig. 1.

Fig. 1

The coupling capacitor (CC ) passes an ac signal from one point to another. At the same time it does not allow the dc to pass through it. Hence it is also called blocking capacitor.

Fig. 2

For example in fig. 2, the ac voltage at point A is transmitted to point B. For this series reactance XC should be very small compared to series resistance RS. The circuit to the left of A may be a source and a series resistor or may be the Thevenin equivalent of a complex circuit. Similarly RL may be the load resistance or equivalent resistance of a complex network. The current in the loop is given by

As frequency increases, decreases, and current increases until it reaches to its maximum value  vin / R. Therefore the capacitor couples the signal properly from A to B when XC<< R. The size of the coupling capacitor depends upon the lowest frequency to be coupled. Normally, for lowest frequency XC £ 0.1R is taken as design rule.

The coupling capacitor acts like a switch, which is open to dc and shorted for ac.

The bypass capacitor Cb is similar to a coupling capacitor, except that it couples an ungrounded point to a grounded point. The Cb capacitor looks like a short to an ac signal and therefore emitter is said ac grounded. A bypass capacitor does not disturb the dc voltage at emitter because it looks open to dc current. As a design rule XCb £ 0.1RE at lowest frequency.

Analysis of CE amplifier:

In a transistor amplifier, the dc source sets up quiescent current and voltages. The ac source then produces fluctuations in these current and voltages. The simplest way to analyze this circuit is to split the analysis in two parts: dc analysis and ac analysis. One can use superposition theorem for analysis .

AC & DC Equivalent Circuits:

For dc equivalent circuit, reduce all ac voltage sources to zero and open all ac current sources and open all capacitors. With this reduced circuit shown in fig. 3 dc current and voltages can be calculated.

Fig. 3

For ac equivalent circuits reduce dc voltage sources to zero and open current sources and short all capacitors. This circuit is used to calculate ac currents and voltage as shown in fig. 4.

Fig. 4

The total current in any branch is the sum of dc and ac currents through that branch. The total voltage across any branch is the sum of the dc voltage and ac voltage across that branch.

Phase Inversion:

Because of the fluctuation is base current; collector current and collector voltage also swings above and below the quiescent voltage. The ac output voltage is inverted with respect to the ac input voltage, meaning it is 180o out of phase with input.

During the positive half cycle base current increase, causing the collector current to increase. This produces a large voltage drop across the collector resistor; therefore, the voltage output decreases and negative half cycle of output voltage is obtained. Conversely, on the negative half cycle of input voltage less collector current flows and the voltage drop across the collector resistor decreases, and hence collector voltage increases we get the positive half cycle of output voltage as shown in fig. 5.

Fig. 5

Lecture - 19: Analysis of CE amplifier

AC Load line:

Consider the dc equivalent circuit fig. 1.

Fig. 1

Assuming IC = IC(approx), the output circuit voltage equation can be written as

The slop of the d.c load line is .

When considering the ac equivalent circuit, the output impedance becomes RC || RL which is less than (RC +RE).

In the absence of ac signal, this load line passes through Q point. Therefore ac load line is a line of slope (-1 / ( RC || RL) ) passing through Q point. Therefore, the output voltage fluctuations will now be corresponding to ac load line as shown in fig. 2. Under this condition, Q-point is not in the middle of load line, therefore Q-point is selected slightly upward, means slightly shifted to saturation side.

Fig. 2

Voltage gain:

To find the voltage gain, consider an unloaded CE amplifier. The ac equivalent circuit is shown in fig. 3. The transistor can be replaced by its collector equivalent model i.e. a current source and emitter diode which offers ac resistance r'e.

Fig. 3

The input voltage appears directly across the emitter diode.

Therefore emitter current ie = Vin / r'e.

Since, collector current approximately equals emitter current and iC = ie and vout = - ie RC (The minus sign is used here to indicate phase inversion)

Further vout = - (Vin RC) / r'e

Therefore voltage gain A = vout / vin = -RC / r'e

The ac source driving an amplifier has to supply alternating current to the amplifier. The input impedance of an amplifier determines how much current the amplifier takes from the ac source.

In a normal frequency range of an amplifier, where all capacitors look like ac shorts and other reactance are negligible, the ac input impedance is defined as

zin= vin/ iin

Where vin, iin are peak to peak values or rms values

The impedance looking directly into the base is symbolized zin (base) and is given by

  Z in(base) = vin / ib ,

Since,v in = ie r'e  

                  » bi b r'e

  zin (base) = b r'e.

From the ac equivalent circuit, the input impedance zin is the parallel combination of R1 , R2 and b r'e.

Zin = R1 || R2 || b r'e

The Thevenin voltage appearing at the output is

vout = A vin

The Thevenin impedance is the parallel combination of RC and the internal impedance of the current source. The collector current source is an ideal source, therefore it has an infinite internal impedance.

zout = RC.

The simplified ac equivalent circuit is shown in fig. 4.

Fig. 4

Example-1:

Select R1 and R2 for maximum output voltage swing in the circuit shown in fig. 5.

Fig. 5

Solution:

We first determine ICQ for the circuit

For maximum swing,

V'CC = 2 VCEQ

The quiescent value for VCE is the given by

VCEQ= (3.13 mA) (500 W ) = 1.56 V

The intersection of the ac load line on the vCE axis is V'CC = 3.13V. From the manufacturer's specification, β for the 2N3904 is 180. RB is set equal to 0.1 βRE. So,

RB = 0.1(180 )(100) = 1.8 K W

VBB = (3.13 x 10-3) (1.1 x 100) + 0.7 = 1.044 V

Since we know VBB and RB, we find R1 and R2,

The maximum output voltage swing, ignoring the non-linearity's at saturation and cutoff, would then be

The load lines are shown on the characteristics of fig. 6.

Fig. 6

The maximum power dissipated by the transistor is calculated to assure that it does not exceed the specifications. The maximum average power dissipated in the transistor is

P(transistor)= VCEQ ICQ = (1.56 (V)) (3.13 mA) =4.87 mW

This is well within the 350 mW maximum given on the specification sheet. The maximum conversion efficiency is

The swamped Amplifier:

The ac resistance of the emitter diode r'e equals 25mV / IE and depends on the temperature. Any change in r'e will change the voltage gain in CE amplifier. In some applications, a change in voltage is acceptable. But in many applications we need a stable voltage gain is required.

To make it stable, a resistance rE is inserted in series with the emitter and therefore emitter is no longer ac grounded. fig .7.

Fig. 7

Because of this the ac emitter current flows through rE and produces an ac voltage at the emitter. If rE is much greater than r'e almost all of the ac input signal appears at the emitter, and the emitter is bootstrapped to the base for ac as well as for dc.

In this case, the collector circuit is given by

Now r'e has a less effect on voltage gain, swamping means rE >> r'e If swamping is less, voltage gain varies with temperature. If swamping is heavy, then gain reduces very much.

Lecture - 20: Design of Amplifier

Example -1 (Common Emitter Amplifier Design)

Design a common-emitter amplifier with a transistor having a β =200 and VBE = 0.7 V. Obtain an overall gain of |A V | ≥ 100 and maximum output voltage swing. Use the CE configuration

shown in fig. 1 with two power supplies. Rsource is the resistance associated with the source, vsource. Let Rsource= 100 Ohms. The output load is 2KΩ. Determine the resistor values of the bias circuitry, the maximum undistorted output voltage swing, and the stage voltage gain.

Fig. 1

Solution:

The maximum voltage across the amplifier is 10 V since the power supply can be visualized as a 10V power supply with a ground in the center. In this case, the ground has no significance to the operation of the amplifier since the input and output are isolated from the power supplies by capacitors.

We will have to select the value for RC and we are really not given enough information to do so. Let choose RC = Rload.

We don't have enough information to solve for RB – we can't use the bias stability criterion since we don't have the value of RE either. We will have to (arbitrarily) select a value of RB or RE. If this leads to a contradiction, or “bad” component values (e.g., unobtainable resistor values), we can come back and modify our choice. Let us select a value for RE that is large enough to obtain a reasonable value of VBB, Selecting RE as 400Ω will not appreciably reduce the collector current yet it will help in maintaining a reasonable value of VBB. Thus,

RB = 0.1 β RE = 0.1 (200)(400) = 8 K Ω

To insure that we have the maximum voltage swing at the output, we will use

Note that we are carrying out our calculations to four places so that we can get accuracy to three places. The bias resistors are determined by

Since we designed the bias circuit to place the quiescent point in the middle of the ac load line, we can use

Vout(undistorted p-p) 1.8 (2.94 x 10-3 ) (2 K Ω || 2 K Ω ) =5.29 V

Now we can determine the gain of the amplifier itself.

Using voltage division, we can determine the gain of the overall circuit.

The value of Rin can be obtained as

Thus the overall gain of the amplifier is

This shows that the common-emitter amplifier provides high voltage gain. However, it is very noisy, it has a low input impedance, and it does not have the stability of the emitter resistor common emitter amplifier.

Example-2 (Emitter-Resistor Amplifier Design)

Design an emitter-resistor amplifier as shown in fig. 2 to drive a 2 KΩ load using a pnp silicon transistor, VCC = -24V, β = 200, Av = -10, and VBE = -0.7 V. Determine all element values and calculate Ai, Rin, ICQ and the maximum undistorted symmetrical output voltage swing for three values of RC as given below:

1. RC = Rload 2. RC = 0.1 Rload 3. RC = 10 Rload

Fig. 2

Solution:

(a) RC = Rload

We use the various equations derived in previous lecture in order to derive the parameters of the circuit.

From the voltage gain, we can solve for R'E.

So R'E = re + RE = 100 Ω

We can find the quiescent value of the collector current IC form the collector-emitter loop using the equation for the condition of maximum output swing.

Therefore,

This is small enough that we shall ignore it to find that RE = 100 Ω. Since we now know β and RE. We can use the design guideline.

RB = 0.1 β RE = 2 k Ω

As designed earlier, the biasing circuitry can be designed in the same manner and given by

VBB = -1.52 V

R1 = 2.14 K Ω

R2 = 3.6 K Ω

The maximum undistorted symmetrical peak to peak output swing is then

Vout (P-P) = 1.8 ICQ (Rload || RC ) = 13.5 V

Thus current gain Ai = -9.1

and input impedance Rin = 1.82 K Ω

(b)   RC = 0.1 Rload

we repeat the steps of parts (a) to find

RC =200 Ω Ri = 390 Ω

ICQ =-57.4 mA R2 =4.7K Ω

r'e = 0.45 Ω vout(p-p) = 18.7 V

RB = 360 Ω Ai = -1.64

VBB = -1.84 V Rin = 327 Ω

     (C)     RC =10 Rload

Once again, we follow the steps of part (a) to find

RC =20 K Ω R1 =3.28K Ω

ICQ =-1.07 mA  R2 = 85.6K Ω

r'e = 24.2 Ω vout(p-p) = 3.9 V

RB = 3.64K Ω   Ai =-14.5

VBB = -0.886 V Rin = 2.91K W

We now compare the results obtained Table-I for the purpose of making the best choice for RC.

  ICQ Ai Rin vout(p-p)

RC = Rload -7.5 mA -9.1 1.82K W 13.5 V

RC = 0.1 Rload -57.4 mA -1.64 327 W 20.8 V

RC = 10 Rload -1.07mA -14.5 2.91W 3.9 V

Table - 1 Comparsion for the three selections of RC

It indicates that of the three given ratios of RC to Rload, RC = Rload has the most desirable performance in the CE amplifier stage.

It can be used as a guide to develop a reasonable designs. In most cases, this choice will provide performance that meets specifications. In some applications, it may be necessary to do additional analysis to find the optimum ratio of RC to Rload.

Example- 3 (Capacitor-Coupled Emitter-Resistor Amplifier Design)

Design an emitter-resistor amplifier as shown in fig. 3 with AV =-10, β =200 and R load = 1K Ω. A pnp transistor is used and maximum symmetrical output swing is required.

Fig. 3

Solution:

As designed earlier, we shall chose RC = Rload = 10 kΩ.

The voltage gain is given by

where R'E= RE + r'e.

Substituting AV, Rload and RC in this equation, we find R'E= 50 Ω.

We need to know the value of r'e to fine RE. We first find Rac and Rdc, and then calculate the Q point as follows (we assume r'e is small, so RE = R'E)

Rac = RE + RC || Rload = 550 Ω

Rdc = RE + RC = 1050 Ω

Now, the first step is to calculate the quiescent collector current needed to place the Q-point into the center of the ac load line (i.e., maximum swing). The equation is

The quantity, r'e , is found as follows

Then

RE = 50 - re = 46.67 Ω

If there were a current gain or input resistance specification for this design, we would use it to solve for the value of RB. Since is no such specification, we use the expression

RB =0.1 β RE = 0.1 (200) (46.6) = 932 Ω

Then continuing with the design steps,

and

The last equality assumes that rO is large compared to RC.

The maximum undistorted peak to peak output swing is given by

1.8 | ICQ | ( RC || Rload )=1.8 ( 0.0075 ) ( 500 ) = 6.75 V

The power delivered into the load and the maximum power dissipated by the transistor are found as

The load lines for this circuit are shown in fig. 4.

Fig. 4

Lecture - 21: Common Collector Amplifie

Common Collector Amplifier:

If a high impedance source is connected to low impedance amplifier then most of the signal is dropped across the internal impedance of the source. To avoid this problem common collector amplifier is used in between source and CE amplifier. It increases the input impedence of the CE amplifier without significant change in input voltage.

Fig. 1, shows a common collector (CC) amplifier. Since there is no resistance in collector circuit, therefore collector is ac grounded. It is also called grounded collector amplifier. When input source drives the base, output appears across emitter resistor. A CC amplifier is like a heavily swamped CE amplifier with a collector resistor shorted and output taken across emitter resistor.

vout = vin - vBE

Fig. 1

Therefore, this circuit is also called emitter follower, because VBE is very small. As vin increases, vout increases.

If vin is 2V, vout = 1.3V

If vin is 3V, vout = 2.3V.

Since vout follows exactly the vin therefore, there is no phase inversion between input and output.

The output circuit voltage equation is given by

VCE = VCC – IE RE

Since IE » IC

\ IC = (VCC – VCE ) / RE

This is the equation of dc load line. The dc load line is shown in Fig. 1.

Voltage gain:

Fig. 2, shows an emitter follower driven by a small ac voltage. The input is applied at the base of transistor and output is taken across the emitter resistor. Fig. 3, shows the ac equivalent circuit of the amplifier. The emitter is replaced by ac resistance r'e.

 Fig. 2 Fig. 3

The ac output voltage is given by

vout = RE ie

and, vin = ie (RE + r'e )

Therefore, A = RE / ( RE +r'e )

Since r'e << RE

\ A » 1.

Therefore, it is a unity gain amplifier. The practical emitter follower circuit is shown in Fig. 4. Fig. 4

The ac source (vS) with a series resistance RS drives the transistor base. Because of the biasing resistor and input impedance of the base, some of the ac signal is lost across the source resistor. The ac equivalent circuit is shown in Fig. 5.

Fig. 5

The input impedance at the base is given by

The total input impedance of an emitter follower includes biasing resistors in parallel with input impedance of the base.

zin = R1 || R2|| b (r'e + RE)

Since b RE is very large as compared to R1 and R2.

Thus,      zin ≈ R1 || R2

Therefore input impedance is very high.

Applying Thevenin's theorem to the base circuit of Fig. 5, it becomes a source vin and a series resistance (R1 || R2 || RS ) as shown in Fig. 6.

Fig. 6

 

Example 1:

Find the Q-point of the emitter follower circuit of fig. 7 with R1 = 10 KΩ and R2 = 20 KΩ. Assume the transistor has a β of 100 and input capacitor C is very-very large.

Fig. 7

Solution:

We first find the Thevenin's equivalent of the base bias circuitry.

RB = R1 || R2 = 6.67 K Ω

From the bias equation we have

Example - 2

Find the output voltage swing of the circuit of fig. 7.

Solution:

The Q-Point location has already been calculated in Example-1. We found that the quiescent collector current is 4.95 mA.

The Output voltage swing = 2 . IC peak . (RE || RLoad) = 2(4.95 x 10-3) (300) = 2.97V

This is less than the maximum possible output swing. Continuing the analysis,

VCEQ = VCC – ICQ RE = 9.03 V

V'CC = VCEQ + ICQ (RE || RLoad ) = 10.5 V

The load lines for this problem are shown in Fig. 8.

Fig. 8

Lecture - 22: Power Amplifier

Darlington Amplifier:

It consists of two emitter followers in cascaded mode as shown in fig. 1. The overall gain is close to unity. The main advantage of Darlington amplifier is very large increase in input impedence and an equal decrease in output impedance .

Fig. 1

DC Analysis:

The first transistor has one VBE drop and second transistor has second VBE drop. The voltage divider produces VTH to the input base. The dc emitter current of the second stage is

IE2 = (VTH – 2 vBE ) / (RE )

The dc emitter current of the first stage that is the base current of second stage is given by

IE1 » IE2 / b2

If r'e(2) is neglected then input impedance of second stage is

Zin (2) = b2 RE

This is the impedance seen by the first transistor. If r'e(1) is also neglected then the input impedance of 1 becomes.

Zin (1) = b1 b2 RE

which is extremely high because of the products of two betas, so the approximate input impedance of Darlington amplifier is

Zin = R1 || R2

Output impedance:

The Thevenin impedance at the input is given by

RTH = RS || R1 || R2

Similar to single stage common collector amplifier, the output impedance of the two stages zout(1) and zout(2) are given by.

Therefore, t he output impedance of the amplifier is very small.

Example-1

Design a single stage npn emitter follower amplifier as shown in fig. 2 with β =60, VBE =0.7V, Rsource =1 KΩ, and VCC= 12V. Determine the circuit element values for the stage to achieve Ai = 10 with a 100 Ω load.

Fig. 2

Solution:

We must select R1, R2 and RE, but we only have two equations. These two equations are specified by the current gain and the placement of the Q-point.

As discussed earlier, the best choice for a CE amplifier is to make RC =R load. We could derive a similar result for RE and Rload in the CC amplifier. We shall therefore begin by constraining REto be equal to Rload. This yields a third equation,

RE = Rload= 100 W

Now finding the load line slopes,

Rac = RE || Rload =50 W

Rdc = RE = 100 V

Since the amplitude of the input is not specified, we choose the quiescent current to place the Q-point in the center of the ac load line for maximum swing.

We now find the value of r'e

Since re is insignificant compared to RE || Rload, it can be ignored. This is usually the case for emitter follower circuits.

Using the equation for current gain we find

Everything in this equation is known except RB. We solve for RB with the result

RB = 1500 W

VBB is found from the base loop.

Continuing with the design as discussed earlier, we find

R1 = 13.8 K Ω

R2 = 1.68 K Ω

The voltage gain of the CC amplifier is approximately unity.

The input resistance is given by

Rin = RB || [ β ( R E || Rload ) ] = 1 kΩ

The output resistance is given by

The maximum peak to peak symmetrical output swing is given by

Vout(p-p) – 1.8 | ICQ| (RE || Rload ) = 7.2 V

The power dissipated in the load, Pload, and the maximum power required of the transistor, Ptransistor, are

 

Example-2 (Capacitor-Coupled CB Design)

Design a CB amplifier using an npn transistor as shown in fig. 3 with β = 100, VCC= 24 V, Rload= 2KΩ, RE = 400Ω VBE = 0.7V. Design this amplifier for a voltage gain of 20.

Fig. 3

Solution:

Since there are fewer equations than there are unknowns, we need an additional constraint, so we set

RC = Rload = 2 K Ω

Then we have,

Rac = 1.40 K Ω and Rdc =2.40 KΩ

For maximum swing, we set ICQ to

We now find that

The current gain is given by

and input impedance is given by

We use the bias equation to find the parameters of the input bias circuitry.

The bias resistors are then given by

The maximum peak-to-peak undistorted output voltage is

Vout(peak-peak) = 1.8 | ICQ | (Rload || RC) = 11.3 V

Lecture - 23: Power Considerations

Power considerations

Power rating is an important consideration in selecting bias resistors since they must be capable of withstanding the maximum anticipated (worst case) power without overheating. Power considerations also affect transistor selection. Designers normally select components having the lowest power handling capability suitable for the design. Frequently, de-rating (i.e., providing a "safety margin" from derived values) is used to improve the reliability of a device. This is similar to using safety factors in the design of mechanical systems where the system is designed to withstand values that exceed the maximum.

Consider a common emitter amplifier circuit shown in fig. 1.

Fig. 1

Derivation of Power Equations

Average power is calculated as follows:

For dc:           (E-1)

For ac:           (E-2)

In the ac equation, we assume periodic waveforms where T is the period. If the signal is not periodic, we must let T approach infinity in equation E-1. Looking at the CE amplifier of fig. 1, the power supplied by the power source is dissipated either in R1 and R2 or in the transistor (and its associated collector and emitter circuitry). The power in R1 and R2 (the bias circuitry) is given by

   (E-3)

where IR1 and IR2 are the (downward) currents in the two resistors. Kirchhoff's current law (KCL) yields a relationship between these two currents and the base quiescent current.

IR1 = IR2 – IB      (E-4)

KVL yields the base loop equation (assuming VEE = 0),

IR2 R2 + IR1 R1 = VCC      (E-5)

These two equations can be solved for the currents to yield,

     (E-6)

In most practical circuits, the power due to IB is negligible relative to the power dissipated in the transistor and in R1 and R2. We will therefore assume that the power supplied by the source is approximately equal to the power dissipated in the transistor and in R1 and R2. This quantity is given by

     (E-7)

Where the source voltage VCC is a constant value. The source current has a dc quiescent component designated by iCEQ and the ac component is designated by ic(t). The last equality of Equation (E-7) assumes that the average value of ic(t) is zero. This is a reasonable assumption. For example, it applies if the input ac signal is a sinusoidal waveform.

The average power dissipated by the transistor itself (not including any external circuitry) is

      (E-8)

For zero signal input, this becomes

P(transitor) = VCEQ ICQ

Where VCEQ and ICQ are the quiescent (dc) values of the voltage and current, respectively.

For an input signal with maximum possible swing (i.e., Q-point in middle and operating to cutoff and saturation),

Fig. 2

Putting these time functions in Equation (E-7) yields the power equation,

       (E-10)

From the above derivation, we see that the transistor dissipates its maximum power (worst case) when no ac signal input is applied. This is shown in fig. 2, where we note that the frequency of the instantaneous power sinusoid is 2ω.

Depending on the amplitude of the input signal, the transistor will dissipate an average power between VCEQ ICQ and one half of this value. Therefore, the transistor is selected for zero input signal so it will handle the maximum (worst case) power dissipation of VCEQ ICQ.

We will need a measure of efficiency to determine how much of the power delivered by the source appears as signal power at the output. We define conversion efficiency as

 

Cascade Amplifier:

To increases the voltage gain of the amplifier, multiple amplifier are connects in cascade. The output of one amplifier is the input to another stage. In this way the overall voltage gain can be increased, when number of amplifier stages are used in succession it is called a multistage amplifier or cascade amplifier. The load on the first amplifier is the input resistance of the second amplifier. The various stages need not have the same voltage and current gain. In practice, the earlier stages are often voltage amplifiers and the last one or two stages are current amplifiers. The voltage amplifier stages assure that the current stages have the proper input swing. The amount of gain in a stage is determined by the load on the amplifier stage, which is governed by the input resistance to the next stage. Therefore, in designing or analyzing multistage amplifier, we start at the output and proceed toward the input.

A n-stage amplifier can be represented by the block diagram as shown in fig. 3.

Fig. 3

In fig. 3, the overall voltage gain is the product of the voltage gain of each stage. That is, the overall voltage gain is ABC.

To represent the gain of the cascade amplifier, the voltage gains are represents in dB. The two power levels of input and output of an amplifier are compared on a logarithmic scale rather than linear scale. The number of bels by which the output power P2 exceeds the input power P1 is defined as

Because of dB scale the gain can be directly added when a number of stages are cascaded.

Types of Coupling:

In a multistage amplifier the output of one stage makes the input of the next stage. Normally a network is used between two stages so that a minimum loss of voltage occurs when the signal passes through this network to the next stage. Also the dc voltage at the output of one stage should not be permitted to go to the input of the next. Otherwise, the biasing of the next stage are disturbed.

The three couplings generally used are.

1. RC coupling 2. Impedance coupling 3. Transformer coupling.

1.RC coupling:  

Fig. 4 shows RC coupling the most commonly used method of coupling from one stage to the next. An ac source with a source resistance R S drives the input of an amplifier. The grounded emitter stage amplifies the signal, which is then coupled to next CE stage the signal is further amplified to get larger output.

In this case the signal developed across the collector resistor of each stage is coupled into the base of the next stage. The cascaded stages amplify the signal and the overall gain equals the product of the individual gains.

Fig. 4

The coupling capacitors pass ac but block dc Because of this the stages are isolated as for as dc is concerned. This is necessary to avoid shifting of Q-points. The drawback of this approach is the lower frequency limit imposed by the coupling capacitor.

The bypass capacitors are needed because they bypass the emitters to ground. Without them, the voltage gain of each stage would be lost. These bypass capacitors also place a lower limit on the frequency response. As the frequency keeps decreasing, a point is reached at which capacitors no longer look like a.c. shorts. At this frequency the voltage gain starts to decrease because of the local feedback and the overall gain of the amplifier drops significantly. These amplifiers are suitable for frequencies above 10 Hz.

Lecture - 24: Cascade Amplifiers

Example - 1

Determine the current and voltage gains for the two-stage capacitor-coupled amplifier shown in fig. 1.

Fig. 1

Solution:

We develop the hybrid equivalent circuit for the multistage amplifier. This equivalent is shown in fig. 2. Primed variables denote output stage quantities and unprimed variables denote input stage quantities.

Fig. 2

Calculations for the output stages are as follows

For the input stage,

The input resistance is determined as:

The current gain, Ai, can be found by applying the equations derived earlier, where the first stage requires using the correct value for Rload derived form the value of Rin to the next stage.

Alternatively, we analyze fig. 2 by extracting four current dividers as shown in fig. 3.

Fig. 3

The current division of the input stage is

The output of the first stage is coupled to the input of he second stage in fig. 3(b). The input resistance of the second stage is

The current in R'in is iload and is given by

Again, i load is current-divided at the input to the second stage. Thus,

The output current is found from fig. 3(c):

The current gain is then

Ai =927

Now using the gain impedance formula, we find the voltage gain:

Impedance Coupling:

At higher frequency impedance coupling is used. The collector resistance is replaced by an inductor as shown in fig. 4. As the frequency increases, XL approaches infinity and each inductor appears open. In other words, inductors pass dc but block ac. When used in this way, the inductors are called RFchokes.

Fig. 4

The advantage is that no signal power is wasted in collector resistors. These RF chokes are relatively expensive and their impedance drops off at lower frequencies. It is suitable at radio frequency above 20 KHz.

Transformer Coupling:

In this case a transformer is used to transfer the ac output voltage of the first stage to the input of the second stage. Fig. 5, the resistors RC is replaced by the primary winding of the transformer. The secondary winding is used to give input to next stage. There is no coupling capacitor. The dc isolation between the two stages provided by the transformer itself. There is no power loss in primary winding because of low resistance.

Fig. 5

At low frequency the size and cost of the transformer increases. Transformer coupling is still used in RF amplifiers. In AM radio receivers, RF signal have frequencies 550 to 1600 KHz. In TV receivers, the frequencies are 54 to 216 MHz. At these frequency the size and cost of the transformer reduces. CS capacitor is used to make other point of transformer grounded, so that ac signal is applied between base and ground.

Tuned Transformer Coupling:

In this case a capacitor is shunted across primary winding to get resonance as shown in fig. 6. At this frequency the gain is maximum and at other frequencies the gain reduces very much. This allows us to filter out all frequencies except the resonant frequency and those near it. This is the principle behind tuning in a radio station or TV channel.

Fig. 6

Example - 2

Design a transformer-coupled amplifier as shown in fig. 7 for a current gain of Ai = 80. Find the power supplied to the load and the power required from the supply.

Fig. 7

Solution:

We first use the design equation to find the location of the Q-point for maximum output swing.

Since the problem statement requires a current gain of 80, the amplifier must have a current gain of 10 because the transformer provides an additional gain of 8. We use the equations from Chapter 5 to find the base resistance RB,

We note that re is sufficiently small to be neglected. Then, solving for RB yields

Now solving for the bias resistors,

The design is now complete. The power delivered by the source is given by

The power dissipated in the load is

We have restricted operation to the linear region by eliminating 5% of the maximum swing near cutoff and saturation. The efficiency is the ratio of the load to source power.

Lecture - 25: Frequency Response of Amplifier

Frequency curve of an RC coupled amplifier:

A practical amplifier circuit is meant to raise the voltage level of the input signal. This signal may be obtained from anywhere e.g. radio or TV receiver circuit. Such a signal is not of a single frequency. But it consists of a band of frequencies, e.g. from 20 Hz to 20 KHz. If the loudspeakers are to reproduce the sound faithfully, the amplifier used must amplify all the frequency components of signal by same amount. If it does not do so, the output of the loudspeaker will not be the exact replica of the original sound. When this happen then it means distortion has been introduced by the amplifier. Consider an RC coupled amplifier circuit shown in fig. 1.

 

Fig. 1 Fig. 2

Fig. 2, shows frequency response curve of a RC coupled amplifier. The curve is usually plotted on a semilog graph paper with frequency range on logarithmic scale so that large frequency range can be accommodated. The gain is constant for a limited band of frequencies. This range is called mid-frequency band and gain is called mid band gain. AVM. On both sides of the mid frequency range, the gain decreases. For very low and very high frequencies the gain is almost zero.

In mid band frequency range, the coupling capacitors and bypass capacitors are as good as short circuits. But when the frequency is low. These capacitors can no longer be replaced by the short circuit approximation.

First consider coupling capacitor. The ac equivalent is shown in fig. 3, assuming capacitors are offering some impedance. In mid-frequency band, the capacitors are ac shorted so the input voltage appears directly across br'e but at low frequency the XC is significant and some voltage drops across XC. The input vin at the base decreases. Thus decreasing output voltage. The lower the frequency the more will be XC and lesser will be the output voltage.

Fig. 3

Similarly at low frequency, output capacitor reactance also increases. The voltage across RL also reduces because some voltage drop takes place across XC. Thus output voltage reduces.

The XC reactance not only reduces the gain but also change the phase between input and output. It would not be exactly 180o but decided by the reactance. At zero frequency, the capacitors are open circuited therefore output voltage reduces to zero.

The other component due to which gain decreases at low frequencies is the bypass capacitor. The function of this capacitor is to bypass ac and blocks dc The impedence of this capacitor in mid frequency band is very low as compared to RE so it behaves like ac short but as the frequency decrease the XCE becomes more and no longer behaves like ac short. Now the emitter is not ac grounded. The ac emitter current i.e. divides into two parts i1 and i2, as shown in fig. 4. A current i1 passes through RE and rest of the current passes through C. Due to ac current i1 in RE, an ac voltage is developed i1 * RE. With the polarity marked at an instant. Thus the effective VL voltage is given by

Vbe = Vs – RE. Fig. 4

Thus the effective voltage input is reduced. The output also reduces. The lower the frequency, the lesser will be the gain. This reduction in gain is due to negative feedback.

As the frequency of the input signal increases, again the gain of the amplifier reduces. Firstly the b of the transistor decreases at higher frequency. Thus reducing the voltage gain of the amplifier at higher frequencies as shown in fig. 5.

The other factor responsible for the reduction in gain at higher frequencies is the presence of various capacitors as shown in fig. 6. They are not physically connected but inherently present with the device.

Fig. Fig. 5

The capacitor Cbc between the base and the collector connects the output with the input. Because of this, negative feedback takes place in the circuit and the gain decreases. This feedback effect is more, when Cbc

provides a path for higher frequency ac currents

The capacitance Cbe offers a low input impedance at higher frequency thus reduces the effective input signal and so the gain falls. Similarly, Cce provides a shunting effect at high frequencies in the output side and reduces gain of the amplifier.

Besides these junction capacitances there are wiring capacitance CW1 and CW2. These reactance are very small but at high frequencies they become 5 to 20 p.f. For a multistage amplifier, the effect of the capacitances Cce,CW1 and CW2 can be represented by single shunt capacitance.

Fig. 6

CS = CW1 + CW2 +Cce.

At higher frequency, the capacitor CS offers low input impedance and thus reduces the output.

Bandwidth of an amplifier:

The gain is constant over a frequency range. The frequencies at which the gain reduces to 70.7% of the maximum gain are known as cut off frequencies, upper cut off and lower cut off frequency. fig. 7, shows these two frequences. The difference of these two frequencies is called Band width (BW) of an amplifier.

BW = f2 – f1.

Fig. 7

At f1 and f2, the voltage gain becomes 0.707 Am(1 / Ö 2). The output voltage reduces to 1 / Ö 2 of maximum output voltage. Since the power is proportional to voltage square, the output power at these frequencies becomes half of maximum power. The gain on dB scale is given by

20 log10(V2 / V1) = 10 log 10 (V2 / V1)2 = 3 dB.

20 log10(V2 / V1) = 20 log10(0.707) =10 log10 (1 / Ö 2)2 = 10 log10(1 / 2) = -3 dB.

If the difference in gain is more than 3 dB, then it can be detected by human. If it is less than 3 dB it cannot be detected.

Direct Coupling:

For applications, where the signal frequency is below 10 Hz, coupling and bypass capacitors cannot be used. At low frequencies, these capacitors can no longer be treated as ac short circuits, since they offer very high impedance. If these capacitors are used then their values have to be extremely large e.g. to bypass a 100 ohm emitter resistor at 10 Hz, we need a capacitor of approximately 1600 m F. The lower the frequency the worse the problem becomes.

To avoid this, direct coupling is used. This means designing the stages without coupling and bypass capacitors, so that the direct current is coupled as well as alternating current. As a result, there is no lower frequency limit. The amplifier enlarges the signal no matter have low frequency including dc or zero frequency.

One Supply Circuit:

Fig. 8, shows a two stage direct coupled amplifier, no coupling or bypass capacitors are used. With a quiescent input voltage 1.4 V, emitter voltage = 1.4 - 0.7 = 0.7 V

The output varies from +6V to +8V. Fig. 8

The main disadvantage is variation in transistor characteristic with variation in temperature. This causes IC and VC to change. Because of the direct coupling the voltage changes are coupled from one stage to next stage, appearing at the final output as an amplified voltage. The unwanted change is called drift.

Grounded Reference Input

For the above amplifier, we need a quiescent voltage of 1.4V. In most applications, it is necessary to have grounded reference input one where the quiescent input voltage is 0 V, as shown in fig. 9.

Fig. 9

The quiescent V CE of the first transistor is only 0.7V and the quiescent of the second transistor is only 1.4V. Both the transistors are operating in active region because VCE(sat) is only 0.1 volt. The input is only in mV, which means that these transistors continue to operate in the active region when a small signal is present.

Lecture - 26: h-Parameters

Small signal low frequency transistor Models:

All the transistor amplifiers are two port networks having two voltages and two currents. The positive directions of voltages and currents are shown in fig. 1.

Fig. 1

Out of four quantities two are independent and two are dependent. If the input current i1 and output voltage v2 are taken independent then other two quantities i2 and v1 can be expressed in terms of i1 and V2.

The equations can be written as

where h11, h12, h21 and h22 are called h-parameters.

        = hi = input impedance with output short circuit to ac.

=hr = fraction of output voltage at input with input open circuited or reverse voltage gain with input open circuited to ac (dimensions).

= hf = negative of current gain with output short circuited to ac.

The current entering the load is negative of I2. This is also known as forward short circuit current gain.

= ho = output admittance with input open circuited to ac.

If these parameters are specified for a particular configuration, then suffixes e,b or c are also included, e.g. hfe ,h ib are h parameters of common emitter and common collector amplifiers

Using two equations the generalized model of the amplifier can be drawn as shown in fig. 2.

Fig. 2

The hybrid model for a transistor amplifier can be derived as follow:

Let us consider CE configuration as show in fig. 3. The variables, iB, iC ,vC, and vB represent total instantaneous currents and voltages iB and vC can be taken as independent variables and vB, IC as dependent variables.

Fig. 3

vB = f1 (iB ,vC )

IC = f2 ( iB , vC ).

Using Taylor 's series expression, and neglecting higher order terms we obtain.

The partial derivatives are taken keeping the collector voltage or base current constant. The Δ vB, Δ vC, Δ iB, Δ iC represent the small signal (incremental) base and collector current and voltage and can be represented as vb ,ib ,vC ,iC.

The model for CE configuration is shown in fig. 4.

Fig. 4

G

Determination of h - parameters:

To determine the four h-parameters of transister amplifier, input and output characteristic are used. Input characteristic depicts the relationship between input voltage and input current with output voltage as parameter. The output characteristic depicts the relationship between output voltage and output current with input current as parameter. Fig. 5, shows the output characterisitcs of CE amplifier.

Fig. 5

The current increments are taken around the quiescent point Q which corresponds to iB = IB and to the collector voltage VCE = VC

The value of hoe at the quiescent operating point is given by the slope of the output characteristic at the operating point (i.e. slope of tangent AB).

hie is the slope of the appropriate input on fig. 6, at the operating point (slope of tangent EF at Q).

Fig. 6

A vertical line on the input characteristic represents constant base current. The parameter hre can be obtained from the ratio (VB2– V B1 ) and (VC2– V C1 ) for at Q.

Typical CE h-parametersof transistor 2N1573 are given below:

hie = 1000 ohm.hre = 2.5 * 10 –4hfe = 50hoe = 25 m A / V

Lecture - 27: h-parameters

Analysis of a transistor amplifier using h-parameters:

To form a transistor amplifier it is only necessary to connect an external load and signal source as indicated in fig. 1 and to bias the transistor properly.

Fig. 1

Consider the two-port network of CE amplifier. RS is the source resistance and ZL is the load impedence h-parameters are assumed to be constant over the operating range. The ac equivalent circuit is shown in fig. 2. (Phasor notations are used assuming sinusoidal voltage input). The quantities of interest are the current gain, input impedence, voltage gain, and output impedence.

Fig. 2

Current gain:

For the transistor amplifier stage, Ai is defined as the ratio of output to input currents.

Input Impedence:

The impedence looking into the amplifier input terminals ( 1,1' ) is the input impedence Zi

Voltage gain:

The ratio of output voltage to input voltage gives the gain of the transistors.

Output Admittance:

It is defined as

Av is the voltage gain for an ideal voltage source (Rv = 0).

Consider input source to be a current source IS in parallel with a resistance RS as shown in fig. 3.

Fig. 3

In this case, overall current gain AIS is defined as

To analyze multistage amplifier the h-parameters of the transistor used are obtained from manufacture data sheet. The manufacture data sheet usually provides h-parameter in CE configuration. These parameters may be converted into CC and CB values. For example fig. 4 hrc

in terms of CE parameter can be obtained as follows.

Fig. 4

For CE transistor configuaration

Vbe = hie Ib + hre Vce

Ic = h fe Ib + hoe Vce

The circuit can be redrawn like CC transistor configuration as shown in fig. 5.

Vbc = hie Ib + hrc Vec

Ic = hfe Ib + hoe Vec

Fig. 5

Lecture - 28: h-parameters

Example - 1

For the circuits shown in fig. 1. (CE–CC configuration) various h-parameters are given

h ie = 2K, hfe = 50, hre = 6 * 10 -4, h oc= 25 m A / V.

hic = 2K, hfe = -51, hre = 1, hoc = 25 m A / V.

Fig. 1

The small signal model of the transistor amplifier is shown in fig. 2.

Fig. 2

In the circuit, the collector resistance of first stage is shunted by the input impedence of last stage. Therefore the analysis is started with last stage. It is convenient; to first compute current gain, input impedence and voltage gain. Then output impedence is calculated starting from first stage and moving towards end.

The effective source resistance R'S2 for the second stage is R01 || RC1 . Thus RS2 = R'01 = 4.65K

\

Overall current gain of the amplifier is Ai and is given by

The equivalent circuit of the amplifier is shown in fig. 3. From the circuit it is clear that the current ic1 is divided into two parts.

Therefore,

and

Overall voltage gain of the amplifier is given by

Fig. 3

Lecture - 24: Frequency response

Overall current gain of the amplifier is Ai and is given by

The equivalent circuit of the amplifier is shown in fig. 3. From the circuit it is clear that the current ic1 is divided into two parts.

Therefore,

and

Fig. 3

Overall voltage gain of the amplifier is given by

Simplified common emitter hybrid model:

In most practical cases it is appropriate to obtain approximate values of A V , A i etc rather than calculating exact values. How the circuit can be modified without greatly reducing the accuracy. Fig. 4 shows the CE amplifier equivalent circuit in terms of h-parameters Since 1 / hoe in parallel with RL is approximately equal to RL if 1 / hoe >> RL then hoe may be neglected. Under these conditions.

Ic = hfe IB .

hre vc = hre Ic RL = hre hfe Ib RL .

Fig. 4

Since h fe.h re » 0.01, this voltage may be neglected in comparison with h ic Ib drop across h ie provided RL is not very large. If load resistance RL is small than hoe and hre can be neglected.

Output impedence seems to be infinite. When Vs = 0, and an external voltage is applied at the output we fined Ib = 0, I C = 0. True value depends upon RS and lies between 40 K and 80K.

On the same lines, the calculations for CC and CB can be done.

CE amplifier with an emitter resistor:

The voltage gain of a CE stage depends upon hfe. This transistor parameter depends upon temperature, aging and the operating point. Moreover, hfe may vary widely from device to device, even for same type of transistor. To stabilize voltage gain A V of each stage, it should be independent of hfe. A simple and effective way is to connect an emitter resistor Re as shown in fig. 5. The resistor provides negative feedback and provide stabilization.

Fig. 5

An approximate analysis of the circuit can be made using the simplified model.

Subject to above approximation A V is completely stable. The output resistance is infinite for the approximate model.

Lecture - 29: Power Amplifier

Power amplifier

The amplifiers in multistage amplifier near the load end in almost all-electronic system employ large signal amplifiers (Power amplifiers) and the purpose of these amplifiers is to obtain power again.

Consider the case of radio receiver, the purpose of a radio receiver is to produce the transmitted programmes with sufficient loudness. Since the radio signal received at the receiver output is of very low power, therefore, power amplifiers are used to put sufficient power into the signal. But these amplifier need large voltage input.

Therefore, it is necessary to amplify the magnitude of input signal by means of small amplifiers to a level that is sufficient to drive the power amplifier stages.

In multistage amplifier, the emphasis is on power gain in amplifier near the load. In these amplifies, the collector currents are much larger because the load resistances are small (i.e impedence of loud speaker is 3.2 ohm).

A power amplifier draws a large amount of dc power form dc source and convert it into signal power. Thus, a power amplifier does not truly amplify the signal power but converts the dc power into signal power.

DC and AC load lines:

Consider a CE amplifier as shown in fig. 1.

Fig. 1

The dc equivalent circuit gives the dc load line as shown in fig. 2.

Fig. 2

Q is the operative point. ICQ and V CEQ are quiescent current and voltage. The ac equivalent circuit is shown in fig. 3.

Fig. 3

This circuit produces ac load line. When no signal is present, the transistor operates at the Q point shown in fig. 4.

Fig. 4

When a signal is present, operating point swings along the ac load line rather than dc load line. The saturation and cut off points on the ac load line are different from those on the dc load line.

During the positive half cycle of ac source, voltage, the collector voltage swing from the Q-point towards saturation. On the negative cycle, the collector voltage swings from Q-point towards cutoff. For a large signal clipping can occur on either side or both sides.

The maximum positive swing from the Q-point is

V CEQ + ICQ rC – VCEQ = I CQ r C.

The maximum negative swing from the Q-point is

0 – V CEQ = - V CEQ.

The ac output compliance (maximum peak to peak unclipped voltage) is given by the smaller of these two approximate values:

      PP = 2 I CQ rC

or PP = 2 V CEQ.

Class A operation:

In a class ‘A' operation transistor operates in active region at all times. This implies that collector current flows for 360° of the ac cycle.

Voltage gain of loaded amplifier

Current gain

ac input power to the base Pin = V in i b

ac output power point = - V out * i C. ( Negative sign is due to phase inversion.)

The variation of PL with VPP is shown in fig. 5. Maximum ac load power is obtained when the output unclipped voltage equals ac output compliance PP.

Fig. 5

When no signal drives the amplifier, the power dissipation of the transistor equals the product of d. voltage and current

P DQ = V CEQ * I CQ

When there is no input signal, PD is maximum as shown in fig. 6.

Fig. 6

It decreases when the peak to peak load voltage increases. The power dissipation must be less than the rating of transistor, otherwise temperature increases and transistor may damage. To reduce the temperature, heat sinks are used that dissipates the heat produced. When Q-point is at the center of ac load line then peak swing above and below Q-point is equal.

Lecture - 30: Power Amplifier

Class A current drain:

In a class A amplifier shown in fig.1, the dc source VCC must supply direct current to the voltage divider and the collector circuit.

Fig. 1

Assuming a stiff voltage divider circuit, the dc current drain of the voltage divider circuit is

I 1 = V CC / (R 1 +R 2 )

In the collector circuit, the dc current drain is

I 2 = I CQ

In a class A amplifier, the sinusoidal variations in collector current averages to zero. Therefore, whether the ac signal is present or not, the dc source must supply an average current of

I S = I 1 + I 2.

This is the total dc current drain. The dc source voltage multiplied by the dc current drain gives the ac power supplied to an amplifier.

P S = V CC IS

Therefore, efficiency of the amplifier, h = (P L (max) / P S ) * 100 %

Where,, P L (max) = maximum ac load line power. In class A amplifier, there is a wastage of power in resistor R C and R E  i.e.  ICQ 2 * (R C + R E ).

To reduce this wastage of power R C and R E should be made zero. R E cannot be made zero because this will give rise to bias stability problem. R C can also not be made zero because effective load resistance gets shorted. This results in more current and no power transfer to the load R L. The R C resistance can, however, be replaced by an inductance whose dc resistance is zero and there is no dc voltage drop across the choke as shown in fig. 1.

Since in most application the load is loudspeaker, therefore power amplifier drives the loudspeaker, and the maximum power transfer takes place only when load impedence is equal to the source impedence. If it is not, the loud speaker gets less power. The impedence matching is done with the help of transformer, as shown in fig. 2.

Fig. 2

The ratio of number of turns is so selected that the impedence referred to primary side can be matched with the output impedence of the amplifier.

Class B amplifier:

The efficiency ( h ) of class A amplifier is poor. The reason is that these circuits draw considerable current from the supply even in the absence of input signals.

In class B operation the transistor collector current flows for only 180° of the ac cycle. This implies that the Q-point is located approximately at cutoff on both dc and ac load lines. The advantages of class B operation are

Lower transistor power dissipation Reduced current drain.

Push pull circuit:

When a transistor operates in class B, it clips off a half cycle. To avoid the resulting distortion, two transistors are used in push pull arrangement. This means that one transistor conducts during positive half cycle and other transistor conducts during negative half cycle. The distortion is low, load power is large and efficiency ( h ) is more. fig. 3, shows how a npn and pnp transistor emitter followers are connected in push pull arrangement.

The dc & ac equivalent circuit are shown in fig. 4 & fig. 5. The biasing resistors are selected so that Q-point is set at cutoff. This biases the emitter diode of each transistor between 0.6V and 0.7V

i.e. I CQ = 0.

Because the biasing resistors are equal each emitter diode is biased with the same voltage. As a result half the supply voltage is dropped across each transistor.

VCEQ = VCC / 2.

Fig. 3

Fig. 4 Fig. 5

Since there is no dc resistance in the collector or emitter circuits, the dc saturation current is infinite. The dc load line is vertical as shown in fig. 6. The most difficult thing is setting up a stable Q-point at cut off. Any significant increase in V BE with temperature can move the Q-point up the dc load line to dangerously high currents. Ac load line is given by

I C(sat) = I CQ + (V CEQ / r E )

V CE (cut off) = V CEQ + I CQ r E

I CQ = 0; V CEQ = V CC / 2

i.e. I C(sat) = V CC / 2RL ( i.e. rE = R L )

V CE (cut off) = V CC / 2.

Fig. 6

When either transistor is conducting, that transistor's operating point swings along the ac load line and the operating point of the other transistor remains at cut off. The voltage swing of the conducting transistor can go from cut off to saturation. In the next half cycle, the other transistor does the same thing.

Therefore, PP = VCC

Voltage gain of loaded amplifier:

AV= R L / (R L + r'e )

Z in (base) » b (RL + r'e )

Z out = r'e + (r B ) / b

A P =A V * Ai

Without signal the capacitor charges up to VCC / 2 relative to ground.

In the positive half cycle of input voltage, the upper transistor conducts and the lower one cut off. The upper transistor acts like an ordinary emitter follower, so that the output voltage approximately equals the input voltage. The current flow through RL is such as direct as to make output positive.

In the negative half cycle of input voltage, the upper transistor cuts off and the lower transistor conducts. The lower transistor acts like an ordinary emitter follower and produces a load voltage

approximately equal to the input voltage (i.e. negative output. Since Q, is off, no current can flow from VCC through Q, but capacitor acts like a battery source and discharges).

During either half cycle, the source sees a high input impedence looking into either base and the load sees a low output impedence.

Lecture - 31: Class B Power Amplifiers

Cross over distortion:

Fig. 1 shows the ac equivalent circuit of a class B push pull amplifier. Suppose that no bias is applied to the emitter diodes. Then the incoming voltage has to rise to about 0.7 V to overcome the barrier potential. Because of this no current flows through Q, when the signal is less than 0.7 V. The action is similar on the other half cycle no current flows in Q2 until ac voltage is more negative the – 0.7 V. If no bias is applied the output of class B amplifier looks like as shown in fig. 1.

Fig. 1

The signal output is distorted. Because of clipping action between half cycles, it no longer is a sine wave. Since the clipping occurs between the time one transistor cuts off and the time the other comes on, it is called cross over distortion. To eliminate cross over distortion, the slight forward bias must be applied to each emitter diode. This means locating the Q-point slightly above cut off as shown in fig. 2. In fact, this is class AB operation. This means that collector current flows for more than 180 degrees but less than 360°.

Fig. 2

Class A amplifier introduces non-linear distortion in input wave means elongates one half cycle and compresses one half cycle. This can be reduced by swamping. In this case it can be further reduced because both half cycles are identical in shape, is given by non-linear distortion is much less than class A.

Load power is given by

Since the ac output compliance equals the peak-to-peak voltage, the maximum load power is

Where, I1 = current through biasing resistance. When no signal is present I2 = ICQ and the current drain is small. But when a signal is present, the current drain increase because the upper collector current becomes large.

If the entire ac load line is used, then the upper transistor has a half sine wave of current through it with a peak value of

IC(sat) = VCEQ / RL

The average value of half sine wave is given by

The dc power is supplied to the circuit is PS = VCC is under no signal conditions, the dc power is small because the current drain is minimum. But when a signal uses the entire ac load line, the dc power supplied to the circuit reaches a maximum.

Biasing a class B amplifier:

In class B amplifier, two complement any transistors are required. Because of the series connection, each transistor drops half the supply voltage. To avoid cross over distortion, the Q-point slightly above cut off, with the correct VBE somewhere between 0.6 and 0.7.

If there is an increase in VBE by few mV it produces 10 times as much emitter current. Because of this it is difficult to find standard resistors that can produce the correct VBE and it needs an adjustable resistor.

The biasing does not solve thermal instability problem. Because for a given collector current, VBE requirement decreases by 2 mV per degree rise in temperature. The voltage divider produces a stiff drive for each diode. Therefore as the temperature increases, the fixed voltage on each emitter diode forces the collector current to increase and this gives rise to thermal run away. When the temperature increases collector current increases, and this is equivalent to Q-point moving up along the vertical dc load line. As the Q-point moves toward higher collector currents, the temperature of the transistor increases further reducing the required V BE .

Fig. 3

One way to avoid thermal run away is to use diode bias. It is based on the concept of current mirror as shown in fig. 3, the base current is much smaller than the current through the resistor and diode. For this reason, I1 and I2 are approximately equal. If the diode curve is identical to the VBE curve of the transistor (VBE , IE ). The diode current equals the emitter and also collector current. Therefore I1 is nearly equal to IC.

I1 = I C .

The collector current is set by controlling the resistor current. This is called a current mirror.

Similarly, pnp transistor can be used as a current mirror. If the VBE curve of the transistor matches the diode curve, the collector equals the resistor current.

Diode bias of class B push pull emitter follower relies on two current mirrors as shown in fig. 4.

Fig. 4

The upper half is an npn current mirror, and the lower half is a pnp current mirror as shown in fig. 4. For diode bias to be immune to changes in temperature, the diode curve must match the VBE curves of the transistor over a wide temperature range. This is easily done in ICs .

Power Calculations for Class B Push-Pull Amplifier

The power delivered by the ac source is split between the transistor and the resistors in the bias circuitry. The ac signal source adds an insignificant additional amunt of power since base currents are small relative to collector currents. Part of the power to the transistor goes to load,

and the other part is dissipated by the transistor itself. The following equations specify the various power relationships in the circuit.

The average power supplied by the dc source is

iCC(t) is the total current and is composed of two components: the dc current through the base bias resistor and diode combination, and the ac collector current through transistor, Q1. Under quiescent conditions (i.e. zero input) Q1 is in cutoff mode. Collector current flows during the positive half of the output signal waveform. Therefore we only need to integrate this component of the power supply signal over the first half cycle.

The maximum values of collector current and power delivered to the transistor are

The ac output power, assuming a sinusoidal input, is

The maximum ac output power is found by substituting ICmax for IC1max to get

The total power supplied to the stage is the sum of the power to the transistor and the power to the bias and compensation circuitry.

If we subtract the power to the load from the power supplied to the transistors, we find the power being dissipated in the transistors the power dissipated by a single transistor is one half of this value. Thus,

we are assuming that the base current is negligible.The efficiency of the Class B push-pull amplifier is the ratio of the output power to the power delivered to the transistor. Thus we neglect the power dissipated by the bias circuitry.

This amplifier is more efficient than a Class A amplifier. It is often used in output circuits where efficiency important design requirement.

Therefore,    

In choosing a transistor, it is important that the power rating is equal to or exceeds the maximum power Pmax.