ee 25 circuit theory nol
TRANSCRIPT
-
7/31/2019 EE 25 Circuit Theory NOL
1/260
TIRUNELVELI
DEPARTMENT OF EEE
II SEM EEE
Prepared By,
SHIBU J.V.BRIGHT,
LECTURER/EEE
-
7/31/2019 EE 25 Circuit Theory NOL
2/260
EE25 CIRCUIT THEORY 3 1 0 100
(Common to EEE, EIE and ICE Branches)
UNIT I BASIC CIRCUITS ANALYSIS 12
Ohms Law Kirchoffs laws DC and AC Circuits Resistors in series and parallel circuits Mesh
current and node voltage method of analysis for D.C and A.C. circuits.
UNIT II NETWORK REDUCTION AND NETWORK THEOREMS FOR DC AND AC CIRCUITS: 12
Network reduction: voltage and current division, source transformation star delta conversion.
Thevenins and Novton & Theorem Superposition Theorem Maximum power transfer
theorem Reciprocity Theorem.
UNIT III RESONANCE AND COUPLED CIRCUITS 12
Series and paralled resonance their frequency response Quality factor and Bandwidth - Selfand mutual inductance Coefficient of coupling Tuned circuits Single tuned circuits.
UNIT IV TRANSIENT RESPONSE FOR DC CIRCUITS 12
Transient response of RL, RC and RLC Circuits using Laplace transform for DC input and A.C. with
sinusoidal input.
UNIT V ANALYSING THREE PHASE CIRCUITS 12
Three phase balanced / unbalanced voltage sources analysis of three phase 3-wire and 4-wire
circuits with star and delta connected loads, balanced & un balanced phasor diagram of
voltages and currents power and power factor measurements in three phase circuits.
TOTAL :60 PERIODS
TEXT BOOKS:
1. William H. Hayt Jr, Jack E. Kemmerly and Steven M. Durbin, Engineering Circuits
Analysis,Tata McGraw Hill publishers, 6th
edition, New Delhi, (2002).
2. Sudhakar A and Shyam Mohan SP, Circuits and Network Analysis and Synthesis,TataMcGraw Hill, (2007).
REFERENCES:
1. Paranjothi SR, Electric Circuits Analysis, New Age International Ltd., New Delhi, (1996).2. Joseph A. Edminister, Mahmood Nahri, Electric circuits, Schaums series, Tata
McGraw-Hill, New Delhi (2001).
3. Chakrabati A, Circuits Theory (Analysis and synthesis), Dhanpath Rai & Sons, New Delhi,
(1999).
4. Charles K. Alexander, Mathew N.O. Sadik, Fundamentals of Electric Circuits, SecondEdition, McGraw Hill, (2003).
-
7/31/2019 EE 25 Circuit Theory NOL
3/260
UNIT I
BASIC CIRCUITSANALYSIS
-
7/31/2019 EE 25 Circuit Theory NOL
4/260
INTRODUCTION
The interconnection of various electric elements in a prescribed manner
comprises as an electric circuit in order to perform a desired function. The electric
elements include controlled and uncontrolled source of energy, resistors, capacitors,inductors, etc. Analysis of electric circuits refers to computations required to determine
the unknown quantities such as voltage, current and power associated with one or more
elements in the circuit. To contribute to the solution of engineering problems one must
acquire the basic knowledge of electric circuit analysis and laws. Many other systems,
like mechanical, hydraulic, thermal, magnetic and power system are easy to analyze and
model by a circuit. To learn how to analyze the models of these systems, first one needs
to learn the techniques of circuit analysis. We shall discuss briefly some of the basic
circuit elements and the laws that will help us to develop the background of subject.
BASIC ELEMENTS & INTRODUCTORY CONCEPTS
Electrical Network: A combination of various electric elements (Resistor, Inductor,
Capacitor, Voltage source, Current source) connected in any manner what so ever is
called an electrical network. We may classify circuit elements in two categories, passive
and active elements.
Passive Element: The element which receives energy (or absorbs energy) and then
either converts it into heat (R) or stored it in an electric (C) or magnetic (L ) field is called
passive element.
Active Element: The elements that supply energy to the circuit is called active element.Examples of active elements include voltage and current sources, generators, and
electronic devices that require power supplies. A transistor is an active circuit element,
meaning that it can amplify power of a signal. On the other hand, transformer is not an
active element because it does not amplify the power level and power remains same
both in primary and secondary sides. Transformer is an example of passive element.
Bilateral Element: Conduction of current in both directions in an element (example: Resistance;
Inductance; Capacitance) with same magnitude is termed as bilateral element.
-
7/31/2019 EE 25 Circuit Theory NOL
5/260
Unilateral Element: Conduction of current in one direction is termed as
unilateral (example: Diode, Transistor) element.
Meaning of Response: An application of input signal to the system will
produce an output signal, the behavior of output signal with time is known as
the response of the system
Linear and Nonlinear Circuits
Non-Linear Circuit: Roughly speaking, a non-linear system is that whose
parameters change with voltage or current. More specifically, non-linear circuit
-
7/31/2019 EE 25 Circuit Theory NOL
6/260
does not obey the homogeneity and additive properties. Volt-ampere
characteristics of linear and non-linear elements are shown in figs. 3.2 - 3.3. In
fact, a circuit is linear if and only if its input and output can be related by a
straight line passing through the origin as shown in fig.3.2. Otherwise, it is a
nonlinear system.
Potential Energy Difference: The voltage or potential energy difference
between two points in an electric circuit is the amount of energy required to
move a unit charge between the two points.
KIRCHHOFFS LAWS
Kirchhoffs laws are basic analytical tools in order to obtain the solutions
of currents and voltages for any electric circuit; whether it is supplied from a
direct-current system or an alternating current system. But with complex
circuits the equations connecting the currents and voltages may become so
numerous that much tedious algebraic work is involve in their solutions.
Elements that generally encounter in an electric circuit can be
interconnected in various possible ways. Before discussing the basic analytical
tools that determine the currents and voltages at different parts of the circuit,
some basic definition of the following terms are considered.
-
7/31/2019 EE 25 Circuit Theory NOL
7/260
-
7/31/2019 EE 25 Circuit Theory NOL
8/260
-
7/31/2019 EE 25 Circuit Theory NOL
9/260
-
7/31/2019 EE 25 Circuit Theory NOL
10/260
Meaning of Circuit Ground and the Voltages referenced to Ground
-
7/31/2019 EE 25 Circuit Theory NOL
11/260
In many cases, such as in electronic circuits, the chassis is shorted to the earth
itself for safety reasons.
Voltage Divider
-
7/31/2019 EE 25 Circuit Theory NOL
12/260
Current divider
-
7/31/2019 EE 25 Circuit Theory NOL
13/260
-
7/31/2019 EE 25 Circuit Theory NOL
14/260
Potentiometer and its function
-
7/31/2019 EE 25 Circuit Theory NOL
15/260
Ideal and Practical Voltage Sources
-
7/31/2019 EE 25 Circuit Theory NOL
16/260
-
7/31/2019 EE 25 Circuit Theory NOL
17/260
-
7/31/2019 EE 25 Circuit Theory NOL
18/260
-
7/31/2019 EE 25 Circuit Theory NOL
19/260
Ideal and Practical Current Sources
Another two-terminal element of common use in circuit modeling is
current source` as depicted in fig.3.17. An ideal current source, which is
represented by a model in fig. 3.17(a), is a device that delivers a constant
current to any load resistance connected across it, no matter what the terminal
voltage is developed across the load (i.e., independent of the voltage across its
terminals across the terminals).
-
7/31/2019 EE 25 Circuit Theory NOL
20/260
-
7/31/2019 EE 25 Circuit Theory NOL
21/260
-
7/31/2019 EE 25 Circuit Theory NOL
22/260
Conversion of a Practical Voltage Source to a Practical Current source and vise-
versa
-
7/31/2019 EE 25 Circuit Theory NOL
23/260
Current source to Voltage Source
-
7/31/2019 EE 25 Circuit Theory NOL
24/260
-
7/31/2019 EE 25 Circuit Theory NOL
25/260
Solution of Electric Circuit Based on Mesh (Loop) Current Method
Let us consider a simple dc network as shown in Figure 4.1 to find the currents
through different branches using Mesh (Loop) current method.
-
7/31/2019 EE 25 Circuit Theory NOL
26/260
-
7/31/2019 EE 25 Circuit Theory NOL
27/260
-
7/31/2019 EE 25 Circuit Theory NOL
28/260
-
7/31/2019 EE 25 Circuit Theory NOL
29/260
-
7/31/2019 EE 25 Circuit Theory NOL
30/260
Solution of Electric Circuit Based on Node Voltage Method
-
7/31/2019 EE 25 Circuit Theory NOL
31/260
-
7/31/2019 EE 25 Circuit Theory NOL
32/260
-
7/31/2019 EE 25 Circuit Theory NOL
33/260
-
7/31/2019 EE 25 Circuit Theory NOL
34/260
-
7/31/2019 EE 25 Circuit Theory NOL
35/260
-
7/31/2019 EE 25 Circuit Theory NOL
36/260
-
7/31/2019 EE 25 Circuit Theory NOL
37/260
-
7/31/2019 EE 25 Circuit Theory NOL
38/260
UNIT II
NETWORK REDUCTION
AND NETWORK
THEOREMS FOR DC
AND AC CIRCUITS
-
7/31/2019 EE 25 Circuit Theory NOL
39/260
DeltaStar conversion
-
7/31/2019 EE 25 Circuit Theory NOL
40/260
Conversion from Delta to Star
-
7/31/2019 EE 25 Circuit Theory NOL
41/260
Conversion from Star to Delta
-
7/31/2019 EE 25 Circuit Theory NOL
42/260
-
7/31/2019 EE 25 Circuit Theory NOL
43/260
SOLUTION:
-
7/31/2019 EE 25 Circuit Theory NOL
44/260
-
7/31/2019 EE 25 Circuit Theory NOL
45/260
-
7/31/2019 EE 25 Circuit Theory NOL
46/260
-
7/31/2019 EE 25 Circuit Theory NOL
47/260
-
7/31/2019 EE 25 Circuit Theory NOL
48/260
-
7/31/2019 EE 25 Circuit Theory NOL
49/260
-
7/31/2019 EE 25 Circuit Theory NOL
50/260
-
7/31/2019 EE 25 Circuit Theory NOL
51/260
-
7/31/2019 EE 25 Circuit Theory NOL
52/260
-
7/31/2019 EE 25 Circuit Theory NOL
53/260
SUPERPOSITION THEOREM
INTRODUCTION
Statement of superposition theorem
In any linear bilateral network containing two or more independent sources
(voltage or current sources or combination of voltage and current sources), the
resultant current / voltage in any branch is the algebraic sum of currents / voltages
caused by each independent sources acting along, with all other independent sources
being replaced meanwhile by their respective internal resistances.
Superposition theorem can be explained through a simple resistive network as
shown in fig.7.1 and it has two independent practical voltage sources and one
practical current source.
-
7/31/2019 EE 25 Circuit Theory NOL
54/260
-
7/31/2019 EE 25 Circuit Theory NOL
55/260
-
7/31/2019 EE 25 Circuit Theory NOL
56/260
-
7/31/2019 EE 25 Circuit Theory NOL
57/260
-
7/31/2019 EE 25 Circuit Theory NOL
58/260
-
7/31/2019 EE 25 Circuit Theory NOL
59/260
-
7/31/2019 EE 25 Circuit Theory NOL
60/260
-
7/31/2019 EE 25 Circuit Theory NOL
61/260
-
7/31/2019 EE 25 Circuit Theory NOL
62/260
Limitations of superposition Theorem
Superposition theorem doesnt work for power calculation. Because power calculations
involve either the product of voltage and current, the square of current or the square of the
voltage, they are not linear operations. This statement can be explained with a simple exampleas given below.
-
7/31/2019 EE 25 Circuit Theory NOL
63/260
Thevenins and Nortons theorems
-
7/31/2019 EE 25 Circuit Theory NOL
64/260
-
7/31/2019 EE 25 Circuit Theory NOL
65/260
-
7/31/2019 EE 25 Circuit Theory NOL
66/260
The procedure for applying Thevenins theorem
-
7/31/2019 EE 25 Circuit Theory NOL
67/260
-
7/31/2019 EE 25 Circuit Theory NOL
68/260
-
7/31/2019 EE 25 Circuit Theory NOL
69/260
-
7/31/2019 EE 25 Circuit Theory NOL
70/260
-
7/31/2019 EE 25 Circuit Theory NOL
71/260
-
7/31/2019 EE 25 Circuit Theory NOL
72/260
-
7/31/2019 EE 25 Circuit Theory NOL
73/260
-
7/31/2019 EE 25 Circuit Theory NOL
74/260
-
7/31/2019 EE 25 Circuit Theory NOL
75/260
Maximum Power Transfer Theorem
-
7/31/2019 EE 25 Circuit Theory NOL
76/260
-
7/31/2019 EE 25 Circuit Theory NOL
77/260
-
7/31/2019 EE 25 Circuit Theory NOL
78/260
Remarks: The Thevenin equivalent circuit is useful in finding the maximum power that a linear circuit
can deliver to a load.
-
7/31/2019 EE 25 Circuit Theory NOL
79/260
-
7/31/2019 EE 25 Circuit Theory NOL
80/260
-
7/31/2019 EE 25 Circuit Theory NOL
81/260
-
7/31/2019 EE 25 Circuit Theory NOL
82/260
Proof of Thevenin Theorem
The basic concept of this theorem and its proof are based on the principle of superposition theorem. Let
us consider a linear system in fig.L.8.8(a).
-
7/31/2019 EE 25 Circuit Theory NOL
83/260
-
7/31/2019 EE 25 Circuit Theory NOL
84/260
-
7/31/2019 EE 25 Circuit Theory NOL
85/260
Norton's Theorem
Norton's Theorem states that it is possible to simplify any linear circuit, no matter how complex,
to an equivalent circuit with just a single current source and parallel resistance connected to a
load. Just as with Thevenin's Theorem, the qualification of linear is identical to that found in the
Superposition Theorem: all underlying equations must be linear (no exponents or roots).
Contrasting our original example circuit against the Norton equivalent: it looks something like
this:
. . . after Norton conversion . . .
Remember that a current source is a component whose job is to provide a constant amount of
current, outputting as much or as little voltage necessary to maintain that constant current.
-
7/31/2019 EE 25 Circuit Theory NOL
86/260
As with Thevenin's Theorem, everything in the original circuit except the load resistance has
been reduced to an equivalent circuit that is simpler to analyze. Also similar to Thevenin's
Theorem are the steps used in Norton's Theorem to calculate the Norton source current (INorton)
and Norton resistance (RNorton).
As before, the first step is to identify the load resistance and remove it from the original circuit:
Then, to find the Norton current (for the current source in the Norton equivalent circuit), place a
direct wire (short) connection between the load points and determine the resultant current. Note
that this step is exactly opposite the respective step in Thevenin's Theorem, where we replaced
the load resistor with a break (open circuit):
With zero voltage dropped between the load resistor connection points, the current through R1 is
strictly a function of B1's voltage and R1's resistance: 7 amps (I=E/R). Likewise, the current
through R3 is now strictly a function of B2's voltage and R3's resistance: 7 amps (I=E/R). Thetotal current through the short between the load connection points is the sum of these two
currents: 7 amps + 7 amps = 14 amps. This figure of 14 amps becomes the Norton source
current (INorton) in our equivalent circuit:
-
7/31/2019 EE 25 Circuit Theory NOL
87/260
Remember, the arrow notation for a current source points in the direction opposite that of
electron flow. Again, apologies for the confusion. For better or for worse, this is standard
electronic symbol notation. Blame Mr. Franklin again!
To calculate the Norton resistance (RNorton), we do the exact same thing as we did for calculating
Thevenin resistance (RThevenin): take the original circuit (with the load resistor still removed),
remove the power sources (in the same style as we did with the Superposition Theorem: voltage
sources replaced with wires and current sources replaced with breaks), and figure total
resistance from one load connection point to the other:
Now our Norton equivalent circuit looks like this:
-
7/31/2019 EE 25 Circuit Theory NOL
88/260
If we re-connect our original load resistance of 2 , we can analyze the Norton circuit as a
simple parallel arrangement:
As with the Thevenin equivalent circuit, the only useful information from this analysis is the
voltage and current values for R2; the rest of the information is irrelevant to the original circuit.However, the same advantages seen with Thevenin's Theorem apply to Norton's as well: if we
wish to analyze load resistor voltage and current over several different values of load resistance,
we can use the Norton equivalent circuit again and again, applying nothing more complex than
simple parallel circuit analysis to determine what's happening with each trial load.
REVIEW: Norton's Theorem is a way to reduce a network to an equivalent circuit composed of a
single current source, parallel resistance, and parallel load.
Steps to follow for Norton's Theorem:
(1) Find the Norton source current by removing the load resistor from the originalcircuit and calculating current through a short (wire) jumping across the open connection
points where the load resistor used to be. (2) Find the Norton resistance by removing all power sources in the original circuit
(voltage sources shorted and current sources open) and calculating total resistance
between the open connection points.
(3) Draw the Norton equivalent circuit, with the Norton current source in parallel withthe Norton resistance. The load resistor re-attaches between the two open points of theequivalent circuit.
(4) Analyze voltage and current for the load resistor following the rules for parallelcircuits
-
7/31/2019 EE 25 Circuit Theory NOL
89/260
Nortons Theorem
In some ways Norton's Theorem can be thought of as the opposite to "Thevenins Theorem", in that Thevenin
reduces his circuit down to a single resistance in series with a single voltage. Norton on the other hand reduces his
circuit down to a single resistance in parallel with a constant current source. Nortons Theorem states that "Any linearcircuit containing several energy sources and resistances can be replaced by a single Constant Current generator in
parallel with a Single Resistor". As far as the load resistance, RL is concerned this single resistance, RS is the value
of the resistance looking back into the network with all the current sources open circuited and IS is the short circuit
current at the output terminals as shown below.
Nortons equivalent circuit.
The value of this "constant current" is one which would flow if the two output terminals where shorted together while
the source resistance would be measured looking back into the terminals, (the same as Thevenin).
For example, consider our now familiar circuit from the previous section.
To find the Nortons equivalent of the above circuit we firstly have to remove the centre 40 load resistor and short
out the terminals A and B to give us the following circuit.
-
7/31/2019 EE 25 Circuit Theory NOL
90/260
When the terminals A and B are shorted together the two resistors are connected in parallel across their two
respective voltage sources and the currents flowing through each resistor as well as the total short circuit current can
now be calculated as:
with A-B Shorted Out
If we short-out the two voltage sources and open circuit terminals A and B, the two resistors are now effectively
connected together in parallel. The value of the internal resistor Rs is found by calculating the total resistance at the
terminals A and B giving us the following circuit.
-
7/31/2019 EE 25 Circuit Theory NOL
91/260
Find the Equivalent Resistance (Rs)
Having found both the short circuit current, Is and equivalent internal resistance, Rs this then gives us the following
Nortons equivalent circuit.
Nortons equivalent circuit.
Ok, so far so good, but we now have to solve with the original 40 load resistor connected across terminals A and B
as shown below.
Again, the two resistors are connected in parallel across the terminals A and B which gives us a total resistance of:
-
7/31/2019 EE 25 Circuit Theory NOL
92/260
The voltage across the terminals A and B with the load resistor connected is given as:
Then the current flowing in the 40 load resistor can be found as:
which again, is the same value of 0.286 amps, we found usingKirchoffscircuit law in the previous tutorials.
Nortons Theorem Summary
The basic procedure for solving a circuit using Nortons Theorem is as follows:
1. Remove the load resistor RL or component concerned.
2. Find RS by shorting all voltage sources or by open circuiting all the current sources. 3. Find IS by placing a shorting link on the output terminals A and B.
4. Find the current flowing through the load resistor RL.
In a circuit, power supplied to the load is at its maximum when the load resistance is equal to the source resistance.
In the next tutorial we will look atMaximum Power Transfer. The application of the maximum power transfer
theorem can be applied to either simple and complicated linear circuits having a variable load and is used to find the
load resistance that leads to transfer of maximum power to the load.
Example-L.8.5 For the circuit shown in fig.8.10(a), find the current through resistor ( branch) using
Nortons theorem & hence calculate the voltage across the current source (). 21LRR==abIcgV
Solution:
Step-1: Remove the resistor through which the current is to be found and short the terminals a andb (see fig.8.10(b)).
http://www.electronics-tutorials.ws/dccircuits/dcp_4.htmlhttp://www.electronics-tutorials.ws/dccircuits/dcp_4.htmlhttp://www.electronics-tutorials.ws/dccircuits/dcp_4.htmlhttp://www.electronics-tutorials.ws/dccircuits/dcp_8.htmlhttp://www.electronics-tutorials.ws/dccircuits/dcp_8.htmlhttp://www.electronics-tutorials.ws/dccircuits/dcp_8.htmlhttp://www.electronics-tutorials.ws/dccircuits/dcp_8.htmlhttp://www.electronics-tutorials.ws/dccircuits/dcp_4.html -
7/31/2019 EE 25 Circuit Theory NOL
93/260
Step-2: Any method can be adopted to compute the current flowing through the a-b branch. Here, we
apply mesh current method.Loop-13R
4(I
1I
2) = 0, where I
2= - 2A
R4I1= 3 + R
4I2= 32 2 = - 1 I
1= - 0.5A
Loop-3
133323333- RI-R(I-I)=0- 3I-4(I+2)=0- 7I-8=08 I=-=7
N138-7+1I=(I-I)=-0.5+=7149A14=(current is flowing from a to b)Step-3: To compute R
N, all sources are replaced with their internal resistances. The equivalent
resistance between a and b terminals is same as the value of Thevenins resistance of the circuit
shown in fig.8.3(d).
-
7/31/2019 EE 25 Circuit Theory NOL
94/260
Step-4: Replace the original circuit with an equivalent Nortons circuit as shown in fig.8.10(d).
NLNNLR1.555I=I=0.643=0.39A (a to b)R+R1.555+1
In order to calculate the voltage across the current source the following procedures are adopted.
Redraw the original circuit indicating the current direction in the load.
bgbgcbcg V=3-10.39=2.61volt2.61 I==1.305A2 I=1.305-0.39=0.915A ('c' to 'b')
V=21.305+4.915=6.26volt ('c' is higher potential than 'g')
L.8.8 Test Your Understanding [Marks: 60]T.1 When a complicated dc circuit is replaced by a Thevenin equivalent circuit, it consists of one ----
--- in series with one --------- . [2]
-
7/31/2019 EE 25 Circuit Theory NOL
95/260
T.2 When a complicated dc circuit is replaced by a Norton equivalent circuit, it consists of ------ in --
--- with one -------. [2]
T.3 The dual of a voltage source is a -----------. [1]
T.4 When a Thevenin theorem is applied to a network containing a current source; the current source
is eliminated by --------- it. [1]
T.5 When applying Nortons theorem, the Norton current is determined with the output terminals ----
----------, but the Norton resistance is found with the output terminals ---------.and subsequently all
the independent sources are replaced -----------. [3]
T.6 For a complicated circuit, the Thevenin resistance is found by the ratio of -------- voltage and -----
------- current. [2]
T.7 A network delivers maximum power to the load when its -------- is equal to the -------- of circuit
at the output terminals. [2]
T.8 The maximum power transfer condition is meaningful in ------------ and --------- systems. [2]
T.9 Under maximum power transfer conditions, the efficiency of the system is only --------- %. [1]
-
7/31/2019 EE 25 Circuit Theory NOL
96/260
UNIT III
RESONANCE AND
COUPLED CIRCUITS
-
7/31/2019 EE 25 Circuit Theory NOL
97/260
-
7/31/2019 EE 25 Circuit Theory NOL
98/260
-
7/31/2019 EE 25 Circuit Theory NOL
99/260
-
7/31/2019 EE 25 Circuit Theory NOL
100/260
-
7/31/2019 EE 25 Circuit Theory NOL
101/260
-
7/31/2019 EE 25 Circuit Theory NOL
102/260
-
7/31/2019 EE 25 Circuit Theory NOL
103/260
-
7/31/2019 EE 25 Circuit Theory NOL
104/260
-
7/31/2019 EE 25 Circuit Theory NOL
105/260
-
7/31/2019 EE 25 Circuit Theory NOL
106/260
-
7/31/2019 EE 25 Circuit Theory NOL
107/260
-
7/31/2019 EE 25 Circuit Theory NOL
108/260
Ideal Transformer
In this lesson, we shall study two winding ideal transformer, its properties and workingprinciple under no load condition as well as under load condition. Induced voltages in primary and
secondary are obtained, clearly identifying the factors on which they depend upon. The ratio between
the primary and secondary voltages are shown to depend on ratio of turns of the two windings. At the
end, how to draw phasor diagram under no load and load conditions, are explained. Importance of
studying such a transformer will be highlighted. At the end, several objective type and numerical
problems have been given for solving.
Key Words: Magnetising current, HV & LV windings, no load phasor diagram, reflected current,
equivalent circuit
23.2 Introduction
Transformers are one of the most important components of any power system. It basically
changes the level of voltages from one value to the other at constant frequency. Being a static
machine the efficiency of a transformer could be as high as 99%.
Big generating stations are located at hundreds or more km away from the load center (where the
power will be actually consumed). Long transmission lines carry the power to the load centre from
the generating stations. Generator is a rotating machines and the level of voltage at which it generates
power is limited to several kilo volts only
-
7/31/2019 EE 25 Circuit Theory NOL
109/260
-
7/31/2019 EE 25 Circuit Theory NOL
110/260
-
7/31/2019 EE 25 Circuit Theory NOL
111/260
-
7/31/2019 EE 25 Circuit Theory NOL
112/260
-
7/31/2019 EE 25 Circuit Theory NOL
113/260
-
7/31/2019 EE 25 Circuit Theory NOL
114/260
-
7/31/2019 EE 25 Circuit Theory NOL
115/260
-
7/31/2019 EE 25 Circuit Theory NOL
116/260
-
7/31/2019 EE 25 Circuit Theory NOL
117/260
-
7/31/2019 EE 25 Circuit Theory NOL
118/260
-
7/31/2019 EE 25 Circuit Theory NOL
119/260
-
7/31/2019 EE 25 Circuit Theory NOL
120/260
-
7/31/2019 EE 25 Circuit Theory NOL
121/260
-
7/31/2019 EE 25 Circuit Theory NOL
122/260
-
7/31/2019 EE 25 Circuit Theory NOL
123/260
-
7/31/2019 EE 25 Circuit Theory NOL
124/260
-
7/31/2019 EE 25 Circuit Theory NOL
125/260
UNIT IV
TRANSIENT RESPONSE
FOR DC CIRCUITS
-
7/31/2019 EE 25 Circuit Theory NOL
126/260
-
7/31/2019 EE 25 Circuit Theory NOL
127/260
-
7/31/2019 EE 25 Circuit Theory NOL
128/260
-
7/31/2019 EE 25 Circuit Theory NOL
129/260
-
7/31/2019 EE 25 Circuit Theory NOL
130/260
-
7/31/2019 EE 25 Circuit Theory NOL
131/260
-
7/31/2019 EE 25 Circuit Theory NOL
132/260
-
7/31/2019 EE 25 Circuit Theory NOL
133/260
-
7/31/2019 EE 25 Circuit Theory NOL
134/260
-
7/31/2019 EE 25 Circuit Theory NOL
135/260
-
7/31/2019 EE 25 Circuit Theory NOL
136/260
-
7/31/2019 EE 25 Circuit Theory NOL
137/260
-
7/31/2019 EE 25 Circuit Theory NOL
138/260
-
7/31/2019 EE 25 Circuit Theory NOL
139/260
-
7/31/2019 EE 25 Circuit Theory NOL
140/260
-
7/31/2019 EE 25 Circuit Theory NOL
141/260
-
7/31/2019 EE 25 Circuit Theory NOL
142/260
-
7/31/2019 EE 25 Circuit Theory NOL
143/260
-
7/31/2019 EE 25 Circuit Theory NOL
144/260
-
7/31/2019 EE 25 Circuit Theory NOL
145/260
-
7/31/2019 EE 25 Circuit Theory NOL
146/260
-
7/31/2019 EE 25 Circuit Theory NOL
147/260
-
7/31/2019 EE 25 Circuit Theory NOL
148/260
-
7/31/2019 EE 25 Circuit Theory NOL
149/260
-
7/31/2019 EE 25 Circuit Theory NOL
150/260
-
7/31/2019 EE 25 Circuit Theory NOL
151/260
-
7/31/2019 EE 25 Circuit Theory NOL
152/260
-
7/31/2019 EE 25 Circuit Theory NOL
153/260
-
7/31/2019 EE 25 Circuit Theory NOL
154/260
-
7/31/2019 EE 25 Circuit Theory NOL
155/260
-
7/31/2019 EE 25 Circuit Theory NOL
156/260
-
7/31/2019 EE 25 Circuit Theory NOL
157/260
-
7/31/2019 EE 25 Circuit Theory NOL
158/260
-
7/31/2019 EE 25 Circuit Theory NOL
159/260
-
7/31/2019 EE 25 Circuit Theory NOL
160/260
-
7/31/2019 EE 25 Circuit Theory NOL
161/260
-
7/31/2019 EE 25 Circuit Theory NOL
162/260
-
7/31/2019 EE 25 Circuit Theory NOL
163/260
-
7/31/2019 EE 25 Circuit Theory NOL
164/260
-
7/31/2019 EE 25 Circuit Theory NOL
165/260
-
7/31/2019 EE 25 Circuit Theory NOL
166/260
-
7/31/2019 EE 25 Circuit Theory NOL
167/260
-
7/31/2019 EE 25 Circuit Theory NOL
168/260
-
7/31/2019 EE 25 Circuit Theory NOL
169/260
-
7/31/2019 EE 25 Circuit Theory NOL
170/260
-
7/31/2019 EE 25 Circuit Theory NOL
171/260
-
7/31/2019 EE 25 Circuit Theory NOL
172/260
-
7/31/2019 EE 25 Circuit Theory NOL
173/260
-
7/31/2019 EE 25 Circuit Theory NOL
174/260
-
7/31/2019 EE 25 Circuit Theory NOL
175/260
-
7/31/2019 EE 25 Circuit Theory NOL
176/260
-
7/31/2019 EE 25 Circuit Theory NOL
177/260
-
7/31/2019 EE 25 Circuit Theory NOL
178/260
-
7/31/2019 EE 25 Circuit Theory NOL
179/260
-
7/31/2019 EE 25 Circuit Theory NOL
180/260
-
7/31/2019 EE 25 Circuit Theory NOL
181/260
-
7/31/2019 EE 25 Circuit Theory NOL
182/260
-
7/31/2019 EE 25 Circuit Theory NOL
183/260
-
7/31/2019 EE 25 Circuit Theory NOL
184/260
-
7/31/2019 EE 25 Circuit Theory NOL
185/260
-
7/31/2019 EE 25 Circuit Theory NOL
186/260
-
7/31/2019 EE 25 Circuit Theory NOL
187/260
-
7/31/2019 EE 25 Circuit Theory NOL
188/260
-
7/31/2019 EE 25 Circuit Theory NOL
189/260
-
7/31/2019 EE 25 Circuit Theory NOL
190/260
UNIT V
ANALYSING THREE
PHASE CIRCUITS
-
7/31/2019 EE 25 Circuit Theory NOL
191/260
-
7/31/2019 EE 25 Circuit Theory NOL
192/260
-
7/31/2019 EE 25 Circuit Theory NOL
193/260
-
7/31/2019 EE 25 Circuit Theory NOL
194/260
-
7/31/2019 EE 25 Circuit Theory NOL
195/260
-
7/31/2019 EE 25 Circuit Theory NOL
196/260
-
7/31/2019 EE 25 Circuit Theory NOL
197/260
-
7/31/2019 EE 25 Circuit Theory NOL
198/260
-
7/31/2019 EE 25 Circuit Theory NOL
199/260
Example
-
7/31/2019 EE 25 Circuit Theory NOL
200/260
-
7/31/2019 EE 25 Circuit Theory NOL
201/260
-
7/31/2019 EE 25 Circuit Theory NOL
202/260
-
7/31/2019 EE 25 Circuit Theory NOL
203/260
Solution of Current in AC Parallel and Series-parallel Circuits
-
7/31/2019 EE 25 Circuit Theory NOL
204/260
-
7/31/2019 EE 25 Circuit Theory NOL
205/260
-
7/31/2019 EE 25 Circuit Theory NOL
206/260
-
7/31/2019 EE 25 Circuit Theory NOL
207/260
-
7/31/2019 EE 25 Circuit Theory NOL
208/260
-
7/31/2019 EE 25 Circuit Theory NOL
209/260
-
7/31/2019 EE 25 Circuit Theory NOL
210/260
-
7/31/2019 EE 25 Circuit Theory NOL
211/260
-
7/31/2019 EE 25 Circuit Theory NOL
212/260
-
7/31/2019 EE 25 Circuit Theory NOL
213/260
-
7/31/2019 EE 25 Circuit Theory NOL
214/260
-
7/31/2019 EE 25 Circuit Theory NOL
215/260
-
7/31/2019 EE 25 Circuit Theory NOL
216/260
-
7/31/2019 EE 25 Circuit Theory NOL
217/260
Generation of Sinusoidal Voltage Waveform (AC) and Some Fundamental
Concepts
-
7/31/2019 EE 25 Circuit Theory NOL
218/260
-
7/31/2019 EE 25 Circuit Theory NOL
219/260
-
7/31/2019 EE 25 Circuit Theory NOL
220/260
-
7/31/2019 EE 25 Circuit Theory NOL
221/260
-
7/31/2019 EE 25 Circuit Theory NOL
222/260
-
7/31/2019 EE 25 Circuit Theory NOL
223/260
As shown earlier, normally the voltage generated, which is also transmitted and then distributed to
the consumer, is the sinusoidal waveform with a frequency of 50 Hz in
-
7/31/2019 EE 25 Circuit Theory NOL
224/260
-
7/31/2019 EE 25 Circuit Theory NOL
225/260
-
7/31/2019 EE 25 Circuit Theory NOL
226/260
-
7/31/2019 EE 25 Circuit Theory NOL
227/260
-
7/31/2019 EE 25 Circuit Theory NOL
228/260
-
7/31/2019 EE 25 Circuit Theory NOL
229/260
-
7/31/2019 EE 25 Circuit Theory NOL
230/260
-
7/31/2019 EE 25 Circuit Theory NOL
231/260
-
7/31/2019 EE 25 Circuit Theory NOL
232/260
-
7/31/2019 EE 25 Circuit Theory NOL
233/260
-
7/31/2019 EE 25 Circuit Theory NOL
234/260
-
7/31/2019 EE 25 Circuit Theory NOL
235/260
-
7/31/2019 EE 25 Circuit Theory NOL
236/260
-
7/31/2019 EE 25 Circuit Theory NOL
237/260
-
7/31/2019 EE 25 Circuit Theory NOL
238/260
-
7/31/2019 EE 25 Circuit Theory NOL
239/260
-
7/31/2019 EE 25 Circuit Theory NOL
240/260
-
7/31/2019 EE 25 Circuit Theory NOL
241/260
Three-phase Balanced Supply
-
7/31/2019 EE 25 Circuit Theory NOL
242/260
-
7/31/2019 EE 25 Circuit Theory NOL
243/260
-
7/31/2019 EE 25 Circuit Theory NOL
244/260
-
7/31/2019 EE 25 Circuit Theory NOL
245/260
-
7/31/2019 EE 25 Circuit Theory NOL
246/260
-
7/31/2019 EE 25 Circuit Theory NOL
247/260
-
7/31/2019 EE 25 Circuit Theory NOL
248/260
-
7/31/2019 EE 25 Circuit Theory NOL
249/260
-
7/31/2019 EE 25 Circuit Theory NOL
250/260
-
7/31/2019 EE 25 Circuit Theory NOL
251/260
Three-phase Delta-Connected Balanced Load
-
7/31/2019 EE 25 Circuit Theory NOL
252/260
-
7/31/2019 EE 25 Circuit Theory NOL
253/260
-
7/31/2019 EE 25 Circuit Theory NOL
254/260
-
7/31/2019 EE 25 Circuit Theory NOL
255/260
-
7/31/2019 EE 25 Circuit Theory NOL
256/260
-
7/31/2019 EE 25 Circuit Theory NOL
257/260
-
7/31/2019 EE 25 Circuit Theory NOL
258/260
-
7/31/2019 EE 25 Circuit Theory NOL
259/260
-
7/31/2019 EE 25 Circuit Theory NOL
260/260