egant combiners_filters catalog.pdf
TRANSCRIPT
Multicasting Matrix MCM 4 x 4800 - 960 MHz / GSM, NMT, AMPS1710 - 2200 MHz / GSM, TDMA, UMTS
Combines up to 4 RBSs into the same antenna system
The advanced MCM enables you to connect 4 Radio Base Stations. The MCM combines the signals and equally splits them between the antenna ports. This is a highly important function when designing shared antenna sys-tems wishing to connect multiple RBSs to the shared antennas.
Sleek design
The MCM incorporates a broad band and low loss product design. The MCM is specifi cally designed for low insertion loss and low inter-modulation. There is no need for terminations or attenuators, which results in very low in-sertion loss and outstanding intermodulation perfomance.
The benefi ts from installing the MCM instead of hybrid combiners and splitters are:
· Lower insertion loss· Fewer system components· Superior antenna isolation· Greater system quality· Cost effective design improvement
RBS 4RBS 4RBS 3RBS 3
RBS 2RBS 2RBS 1RBS 1
Floor 1
Floor 2
Floor 3
Floor 4
EGANTCELLULAR COMPONENTS
Egant Cellular ComponentsBox 945SE-114 79 StockholmSwedenPhone: +46 (0)8 620 06 50Fax: +46 (0)70 386 53 53E-mail: [email protected]
RevC
Technical Specifi cations for the Multicasting Matrix (MCM)Below are some typical data. For more detailed information, please contact us.
Electrical Specifi cationsProduct number:Passband:
Isolation between ports:Input return loss:Insertion loss:Coupling:Max input power/port:
3rd order intermodulation:IM3, 2 x 43 dBm:Impedance in/out:
EG 500 8001800 - 960 MHz
> 25 dB > 22.0 dB< 0.3 dB6.2 + 0.5 dB100 W
< - 105 dBm, 148 dBc50 Ohm
EG 500 80021710 - 2200 MHz
> 25 dB > 22.0 dB< 0.3 dB6.2 + 0.5 dB100 W
< - 105 dBm, 148 dBc50 Ohm
Mechanical Specifi cationsDimensions (W x H x D):Connectors:
214 x 25 x 110 mmN (f)
214 x 25 x 110 mmN (f)
Environmental Specifi cationsTemp. range (normal operation):Humidity:Sealing:
Egant reserves the right to change this product specifi cation at any time without notice.
-30 to +70º CRelative 5 - 100%IP65
-30 to +70º CRelative 5 - 100%IP65
ANT ANT ANT ANT
IN / OUT IN / OUT IN / OUT IN / OUT
4-Way Combiner800 - 960 MHz / NMT, GSM9001710 - 2200 MHz / GSM1800, UMTS
Combines up to 4 RBSs into the same antenna system
The 4-way combiner enables the connection of 4 Radio Base Stations to the combiner. The combiner combines the signal and equally splits the signals between the antenna ports.
This is a highly important function when designing shared antenna systems wishing to connect multiple RBSs to the shared antennas.
Innovative design
The 4-way combiner is a broad band and low loss product design. It is intentionally de-signed for low insertion loss and lowintermodulation. There is no need for terminations or attenuators, which results in very low insertion loss and outstanding inter-modulation performance.
The benefi ts of using our 4-way combiner instead of 3 dB hybrid com-biners and splitters are:
· Lower insertion loss· Fewer system components· Superior antenna isolation· Greater system quality· Cost effective design improvement
EGANTCELLULAR COMPONENTS
Egant Cellular ComponentsBox 945SE-114 79 StockholmSwedenPhone: +46 (0)8 62 00 650Fax: +46 (0)70 386 53 53E-mail: [email protected]
Technical Specifi cations for the 4-Way CombinerBelow are some typical data. For more detailed information, please contact us.
Electrical Specifi cationsProduct number:Passband:
Insertion loss:
Coupling:
Input return loss:Isolation between ports:Intermodulation 2 x 43 dBm:
Max input power/port:Max peak power:
Impedance in/out:
EG 500 8003800 - 960 MHz
< 0.2 dB
6.2 +/- 0.25 dB
> 26.0 dB> 30 dB (35 dB typ.)< 107 dBm (150 dBc)
100 W3 kW
50 Ohm
EG 500 80041710 - 2200 MHz
< 0.2 dB
6.2 +/- 0.25 dB
> 26.0 dB> 30 dB (35 dB typ.)< 107 dBm (150 dBc)
100 W3 kW
50 Ohm
Mechanical Specifi cationsDimensions (W x H x D):Connectors:
153 x 20 x 153 mmN (f)
153 x 20 x 153 mmN (f)
Environmental Specifi cationsTemp. range (normal operation):Humidity:Sealing:
Egant reserves the right to change this product specifi cation at any time without notice.
-30 to +70º CRelative 5 - 100%IP65
-30 to +70º CRelative 5 - 100%IP65
RevB
4-Way Combiner MCME-GSM900
Combines up to 4 RBSs into the sameantenna system
This extended range 4-way combiner enables you to connect 4 Radio Base Stations. The combiner combines the signal and equally splits it between the antenna ports. This is a highly important function when designing shared antenna systems wishing to connect multiple RBSs to the shared antennas.
Innovative design
The 4-way combiner incorporates a broadband and low loss product design. The 4-waycombiner is designed for low insertion lossand intermodulation. There is no need for termi-nations or attenuators, which results in very low insertion loss and outstanding intermodulation performance.
The benefi ts from installing the 4-waycombiner instead of hybrid combinersand splitters are:
· Lower insertion loss· Fewer system components· Superior antenna isolation· Greater system quality· Cost effective design improvement
RBS 4RBS 4RBS 3RBS 3
RBS 2RBS 2RBS 1RBS 1
ANT2ANT2
ANT1ANT1 ANT3ANT3
ANT4ANT4
EGANTCELLULAR COMPONENTS
Egant Cellular ComponentsBox 945SE-114 79 StockholmSwedenPhone:+46 (0)8 620 06 50Fax: +46 (0)70 386 53 53E-mail: [email protected]
RevB
Technical Specifi cations for the 4-Way Combiner (MCM) E-GSM900Below are some typical data. For more detailed information, please contact us.
Electrical Specifi cationsProduct number:Passband:
Isolation between ports:Input return loss:Coupling:Max input power/port:3rd order intermodulation:IM3, 2 x 43 dBm:Impedance in/out:
EG 603 0021880 - 960 MHz, E-GSM900
> 25 dB> 18.0 dB6.4 + 0.7 dB100 W
< - 117 dBm, 160 dBc50 Ohm
Mechanical Specifi cationsDimensions (W x H x D):Connectors:
450 x 100 x 190 mm7/16 (f)
Environmental Specifi cationsTemp. range (normal operation):Humidity:Sealing:
Egant reserves the right to change this product specifi cation at any time without notice.
-30 to +70º CRelative 5 - 100%IP65
MCM 4-Way Combiner BroadbandTETRA, CDMA2000, GSM900376 - 960 MHz
Combines up to 4 RBSs into the same antenna system
The 4-way combiner enables you to connect 4 Base Stations. The combiner combines the signal and equally splits it between the an-tenna ports.
This is a highly important function when designing shared antenna systems wishing to connect multiple RBSs to the shared antennas.
Innovative design
The 4-way combiner incorporates a broad band and low loss product design. The 4-way combiner is designed for low insertion loss and intermodulation.
There is no need for terminations or attenu-ators, which results in very low insertion loss and outstanding intermodulation perfor-mance.
The benefi ts from installing the 4-way combiner instead of hybrid combiners and splitters are:
· Lower insertion loss· Fewer system components· Superior antenna isolation· Greater system quality· Cost effective design improvement
RBS 4RBS 4RBS 3RBS 3
RBS 2RBS 2RBS 1RBS 1
ANT2ANT2
ANT1ANT1 ANT3ANT3
ANT4ANT4
EGANTCELLULAR COMPONENTS
Egant Cellular ComponentsBox 945SE-114 79 StockholmSwedenPhone: +46 (0)8 62 00 650Fax: +46 (0)70 386 53 53E-mail: [email protected]
RevB
Technical Specifi cations for 4-Way Combiner Broadband (MCM)Below are some typical data. For more detailed information, please contact us.
Electrical Specifi cationsProduct number:Passband:
Isolation between ports:Input return loss:Coupling:Max input power/port:
3rd order intermodulation:IM3, 2 x 43 dBm:Impedance in/out:
EG 500 8008376 - 500 MHz, 880 - 960 MHz
> 25 dB> 18.0 dB6.4 + 0.7 dB100 W
< - 117 dBm, 160 dBc50 Ohm
EG 603 0014376 - 500 MHz, 880 - 960 MHz
> 25 dB> 18.0 dB6.4 + 0.7 dB100 W
< - 117 dBm, 160 dBc50 Ohm
Mechanical Specifi cationsDimensions (W x H x D):Connectors:
310 x 130 x 130 mmN (f)
380 x 150 x 130 mm7/16 (f)
Environmental Specifi cationsTemp. range (normal operation):Humidity:Sealing:
Egant reserves the right to change this product specifi cation at any time without notice.
-30 to +70º CRelative 5 - 100%IP65
-30 to +70º CRelative 5 - 100%IP65
4-Way Combiner Broadband MCM800 - 2200 MHz, 700 - 2700MHzTETRA, GSM 900, GSM 1800, UMTS, W-LAN
Combines up to 4 RBSs into the same antenna system
The 4-way combiner enables the connection of 4 Radio Base Stations. The combiner com-bines the signal and equally splits it between the antenna ports.
This is an extremely important function when designing shared antenna systems wishing to connect multiple RBSs to the shared antennas.
Innovative design
The 4-way combiner is a broad band and low loss product design. The combiner is specifi -cally designed with low insertion loss and intermodulation in mind. There is no need for terminations or attenuators, which results in very low insertion loss and outstanding inter-modulation performance.
The benefi ts from installing the 4-way combiner instead of hybrid combiners and splitters are:
· Lower insertion loss· Fewer system components· Superior antenna isolation· Greater system quality· Cost effective design improvement
UM
TSU
MTS
RB
S 1
RB
S 1
RB
S 2
RB
S 2
ANT2ANT2
ANT1ANT1
RB
S 3
RB
S 3
RB
S 4
RB
S 4
ANT3ANT3
ANT4ANT4
EGANTCELLULAR COMPONENTS
Egant Cellular ComponentsBox 945SE-114 79 StockholmSwedenPhone: +46 (0)8 62 00 650Fax: +46 (0)70 386 53 53E-mail: [email protected]
RevC
Technical Specifi cations for 4-Way Combiner Broadband (MCM)Below are some typical data. For more detailed information, please contact us.
Electrical Specifi cationsProduct number:Passband:
EG 500 8005800 - 2200 MHz
EG 603 0009700 - 2700 MHz
Isolation between ports:Input return loss:Coupling:Max input power/port:
3rd order intermodulation:IM3, 2 x 43 dBm:Impedance in/out:
> 25 dB> 20.0 dB6.4 + 0.7 dB100 W
< - 107 dBm, 160 dB50 Ohm
> 25 dB> 18.5.0 dB6.4 + 0.7 dB100 W
< - 107 dBm, 160 dB50 Ohm
Mechanical Specifi cationsDimensions (W x H x D):Connectors:
310 x 130 x 130 mm7/16 (f)
310 x 130 x 130 mm7/16 (f)
Environmental Specifi cationsTemp. range (normal operation):Humidity:Sealing:
Egant reserves the right to change this product specifi cation at any time without notice.
-30 to +70º CRelative 5 - 100%IP65
-30 to +70º CRelative 5 - 100%IP65
4-Way Combiner Broadband376 - 2200 MHz
Combines up to 4 RBSs into the shared antenna system
The 4-way combiner enables the connection of 4 Radio Base Stations. It combines the signal and equally splits it between the antenna ports. This is a highly important function when designing shared antenna systems wishing to connect multiple RBSs to the shared antennas.
Innovative design
The 4-way combiner incorporates a broad band and low loss product design. It is spe-cifi cally designed with low insertion loss and intermodulation in mind. There is no need for terminations or attenuators, which results in very low insertion loss and outstanding inter-modulation performance.
The benefi ts from installing the 4-way combiner instead of hybrid combiners and splitters are:
· Lower insertion loss· Fewer system components· Superior antenna isolation· Greater system quality· Cost effective design improvement
RBS 4RBS 4RBS 3RBS 3
RBS 2RBS 2RBS 1RBS 1
ANT2ANT2
ANT1ANT1 ANT3ANT3
ANT4ANT4
EGANTCELLULAR COMPONENTS
Egant Cellular ComponentsBox 945SE-114 79 StockholmSwedenPhone: +46 (0)8 620 06 50Fax: +46 (0)70 386 53 53E-mail: [email protected]
RevB
Technical Specifi cations for 4-Way Combiner Broadband (MCM)Below are some typical data. For more detailed information, please contact us.
Electrical Specifi cationsProduct number:Passband:
Isolation between ports:
Input return loss:
Coupling:
Max input power/port:
3rd order intermodulation:IM3, 2 x 43 dBm:
Impedance in/out:
EG 603 0008376 - 2200 MHz
> 25 dB (30 dB typ)
> 17.0 dB
6.4 + 1.0 dB
100 W
< - 117 dBm, 160 dBc
50 Ohm
Mechanical Specifi cations Dimensions (W x H x D):Connectors:
410 x 130 x 130 mm7/16 (f)
Environmental Specifi cationsTemp. range (normal operation):Humidity:Sealing:
Egant reserves the right to change this product specifi cation at any time without notice.
-30 to +70º CRelative 5 - 100%IP65
Triple Band Combiner/Dual Band Combiner UMTS, GSM1800, GSM900/GSM1800, UMTS
Combines 3 RBSs into 1 antenna port
This triple band combiner enables the connec-tion of 3 Radio Base Stations to the combiner:
1 GSM900 Radio Base Station1 GSM1800 Radio Base Station1 UMTS Radio Base Station
The combiner combines the 3 signals to1 antenna port, or splits the signal to the 3 RBSs in the receiving direction.
This is a highly desirable function when designing shared antenna systems wishing to connect multiple RBSs to the shared antennas.
Reduces cost
By utilizing our triple band combiner you will reduce the cost of antennas, feeders and installation.
It eliminates the cost ineffi cient need to make one antenna installation for each system. By simply connecting the RBSs into the com-biner it will immediately render you all the benefi ts of antenna sharing.
Dual Band Combiner - combines 2 RBSs into 1 antenna port
The dual band combiner enables you to connect 2 Radio Base Stations to the combiner:
1 GSM1800 Radio Base Station1 UMTS Radio Base Station
GSM
900
GSM
900
GSM
180
0G
SM 1
800
UM
TSU
MTS
ANTANT EGANTCELLULAR COMPONENTS
Egant Cellular ComponentsBox 945SE-114 79 StockholmSwedenPhone: +46 (0)8 62 00 650Fax: +46 (0)70 386 53 53E-mail: [email protected]
RevB
Technical Specifi cations for the Triple Band Combiner/Dual Band CombinerBelow are some typical data. For more detailed information, please contact us.
Electrical Specifi cationsProduct number:Passband:Port1: GSM900Port2: GSM1800Port3: UMTS
Insertion loss:Port1: GSM900 - ANTPort2: GSM1800 - ANTPort3: UMTS - ANT
Input return loss:Isolation between systems:
Max input power/port:Port1: GSM900Port2: GSM1800Port3: UMTS
Impedance in/out:
Intermodulation:IM3 2 x 43 dBm:
DC by-pass between all inputs to output:
EG 100 9012
806 - 960 MHz1710 - 1880 MHz1920 - 2170 MHz
< 0.20 dB < 0.30 dB < 0.45 dB
> 21.0 dB> 50 dB
< 200 W< 200 W< 100 W
50 Ohm
<-117 dBm (160 dBc)
1A, max, per input
EG 100 9009
1710 - 1880 MHz1920 - 2170 MHz
< 0.40 dB < 0.45 dB
> 20.0 dB> 50 dB
< 200 W< 100 W
50 Ohm
<-117 dBm (160 dBc)
1A, max, per input
Mechanical Specifi cationsDimensions (W x H x D):Connectors:Weight:
230 x 200 x 555 mm7/16 (f)3.6 kg
245 x 210 x 50 mm7/16 (f)3.6 kg
Environmental Specifi cationsTemp. range (normal operation):Humidity:Sealing:
Egant reserves the right to change this product specifi cation at any time
without notice.
-40 to +70º CRelative 5 - 100%IP66
-40 to +70º CRelative 5 - 100%IP66
Triple Band Combiner160MHz, TETRA, GPS
Combines 3 Radio Systems into 1 An-tenna Port
This triple band combiner enables the connec-tion of 3 Systems to the combiner:
1 160MHz System1 TETRA System1 GSP System
The combiner combines the 3 signals to1 antenna port, or splits the signal to the 3 Systems in the receiving direction.
This is a highly desirable function when designing shared antenna systems wishing to connect multiple Radio Systems to the shared antennas.
Reduces cost
By utilizing the Egant triple band combiner you will reduce the cost of antennas, feeders and installation.
It eliminates the cost ineffi cient need to make one antenna installation for each system. By simply connecting the RBSs into the com-biner it will immediately render you all the benefi ts of antenna sharing.
EGANTCELLULAR COMPONENTS
Egant Cellular ComponentsBox 945SE-114 79 StockholmSwedenPhone: +46 (0)8 620 06 50Fax: +46 (0)70 386 53 53E-mail: [email protected]
RevB
Technical Specifi cations for the Triple Band CombinerBelow are some typical data. For more detailed information, please contact us.
Electrical Specifi cationsProduct number:Passband:Port 1: 160MHzPort 2: TETRAPort 3: GPS
Insertion loss:Port 1: 160MHz - ANTPort 2: TETRA - ANTPort 3: GPS - ANT
Input return loss:Isolation between systems:
Max input power/port:Port 1: 160MHzPort 2: TETRAPort 3: GPS
Impedance in/out:
EG 602 0044
88 - 180 MHz376 - 495 MHz1570 - 1580 MHz
< 0.9 dB < 0.9 dB < 0.5 dB
> 14.0 dB> 30 dB
10 W20 W10 W
50 Ohm
Mechanical Specifi cationsDimensions (W x H x D):Connectors:Weight:
350 x 130 x 60 mm7/16 (f)3,5 kg
Environmental Specifi cationsTemp. range (normal operation):Humidity:Sealing:
Egant reserves the right to change this product specifi cation at any time
without notice.
-40 to +70º CRelative 5 - 100%IP65
Triple Band CombinerUMTS, GSM1800, GSM900
Combines 3 RBSs into 1 Antenna Port
This triple band combiner enables the connec-tion of 3 Radio Base Stations to the combiner:
1 GSM900 Radio Base Station1 GSM1800 Radio Base Station1 UMTS Radio Base Station
The combiner combines the 3 signals to1 antenna port, or splits the signal to the 3 RBSs in the receiving direction.
This is a highly desirable function when designing shared antenna systems wishing to connect multiple RBSs to the shared antennas.
Reduces cost
By utilizing the Egant triple band combiner you will reduce the cost of antennas, feeders and installation.
It eliminates the cost ineffi cient need to make one antenna installation for each system. By simply connecting the RBSs into the com-biner it will immediately render you all the benefi ts of antenna sharing.
GSM
900
GSM
900
GSM
180
0G
SM 1
800
UM
TSU
MTS
ANTANTEGANT
CELLULAR COMPONENTS
Egant Cellular ComponentsBox 945SE-114 79 StockholmSwedenPhone: +46 (0)8 62 00 650Fax: +46 (0)70 386 53 53E-mail: [email protected]
RevB
Technical Specifi cations for the Triple Band CombinerBelow are some typical data. For more detailed information, please contact us.
Electrical Specifi cationsProduct number:Passband:Port1: GSM900Port2: GSM1800Port3: UMTS
Insertion loss:Port1: GSM900 - ANTPort2: GSM1800 - ANTPort3: UMTS - ANT
Input return loss:Isolation between systems:
Max input power/port:Port1: GSM900Port2: GSM1800Port3: UMTS
Impedance in/out:
EG 100 9019
880 - 960 MHz1710 - 1880 MHz1920 - 2170 MHz
< 1.3 dB < 1.3 dB < 1.3 dB
> 16.0 dB> 30 dB
20 W20 W20 W
50 Ohm
EG 100 9020
880 - 960 MHz1710 - 1880 MHz1920 - 2170 MHz
< 1.3 dB < 1.3 dB < 1.3 dB
> 16.0 dB> 30 dB
20 W20 W20 W
50 Ohm
Mechanical Specifi cationsDimensions (W x H x D):Connectors:Weight:
195 x 130 x 30 mmSMA (f)1 kg
195 x 130 x 30 mmN (f)1 kg
Environmental Specifi cationsTemp. range (normal operation):Humidity:Sealing:
Egant reserves the right to change this product specifi cation at any time
without notice.
-40 to +70º CRelative 5 - 100%IP65
-40 to +70º CRelative 5 - 100%IP65
Dual Band Combiner 800 - 1000 MHz, 1700 - 2170 MHz
Combines 2 RBSs into 1 Antenna Port
This Dual Band Combiner enables the connec-tion of 2 Radio Base Stations to the combiner:
1 GSM900 Radio Base Station1 GSM1800 Radio Base Station or1 UMTS Radio Base Station
The Combiner combines the 2 signals to 1 antenna port, or splits the signal to the 2 RBSs in the receiving direction.
This is a highly desirable function when designing shared antenna systems wishing to connect multiple RBSs to the shared antennas.
Reduces cost
By utilizing the Egant Dual Band Combiner you will reduce the cost of antennas, feeders and installation.
It eliminates the cost ineffi cient need to to make one antenna installation for each sys-tem. By simply connecting the RBSs into the combiner it will immediately render you all the benefi ts of antenna sharing.
GSM
900
GSM
900
GSM
1800
GSM
1800
UM
TSU
MTS
ANTANTEGANT
CELLULAR COMPONENTS
Egant Cellular ComponentsBox 945SE-114 79 StockholmSwedenPhone: +46 (0)8 62 00 650Fax: +46 (0)70 386 53 53E-mail: [email protected]
RevB
Technical Specifi cations for the Dual Band CombinerBelow are some typical data. For more detailed information, please contact us.
Electrical Specifi cationsProduct number: Passband:Port1: GSM900Port2: GSM1800 / UMTS
Insertion loss:Port1: GSM900Port2: GSM1800 / UMTS
Input return loss:Isolation between systems:
Max input power/port:Port1: GSM900Port2: GSM1800 / UMTS
Impedance in/out:
Intermodulation:IM3, 2 x 43 dBm:
EG 100 9013
800 - 1000 MHz1700 - 2170 MHz
< 0.15 dB < 0.25 dB
> 21.0 dB> 50 dB
< 250W< 150W
50 Ohm
< -117 dBm (160 dBc)
EG 100 9014
800 - 1000 MHz1700 - 2170 MHz
< 015 dB < 0.25 dB
> 21.0 dB> 50 dB
< 250W< 150W
50 Ohm
< -117 dBm (160 dBc)
Mechanical Specifi cationsDimensions (W x H x D):Connectors:Weight:
117 x 215 x 50 mm7/16 (f)1.5 kg
117 x 215 x 50 mmN (f)1.5 kg
Environmental Specifi cationsTemp. range (normal operation):Humidity:Sealing:
Egant reserves the right to change this product specifi cation at any time
without notice.
-40 to +70º CRelative 5 - 100%IP65
-40 to +70º CRelative 5 - 100%IP65
Dual Band CombinerGSM900, GSM1800
Combines 2 RBSs into 1 Antenna Port
This triple band combiner enables the connec-tion of 2 Radio Base Stations to the combiner:
1 GSM900 Radio Base Station1 GSM1800 Radio Base Station
The combiner combines the 2 signals to1 antenna port, or splits the signal to the 2 RBSs in the receiving direction.
This is a highly desirable function when designing shared antenna systems wishing to connect multiple RBSs to the shared antennas.
Reduces cost
By utilizing the Egant dual band combiner you will reduce the cost of antennas, feeders and installation.
It eliminates the cost ineffi cient need to make one antenna installation for each system. By simply connecting the RBSs into the com-biner it will immediately render you all the benefi ts of antenna sharing.
EGANTCELLULAR COMPONENTS
Egant Cellular ComponentsBox 945SE-114 79 StockholmSwedenPhone: +46 (0)8 620 06 50Fax: +46 (0)70 386 53 53E-mail: [email protected]
Rev P1A
Technical Specifi cations for the Dual Band CombinerBelow are some typical data. For more detailed information, please contact us.
Electrical Specifi cationsProduct number:Passband:Port 1: GSM900Port 2: GSM1800
Insertion loss:Port 1: GSM900 - ANTPort 2: GSM1800 - ANT
Input return loss:Isolation between systems:Rejection 1920-2170MHz (UMTS)
Max input power/port:Port 1: GSM900Port 2: GSM1800
Impedance in/out:
EG 602 0034
880 - 960 MHz1710 - 1880 MHz
< 0.2 dB (0,1 dB typ)< 0.4 dB (0,2 dB typ)
> 18.0 dB> 50 dB> 65.0 dB
100 W100 W
50 Ohm
Mechanical Specifi cationsDimensions (W x H x D):Connectors:Weight:
195 x 185 x 55 mm7/16 (f)4 kg
Environmental Specifi cationsTemp. range (normal operation):Humidity:Sealing:
Egant reserves the right to change this product specifi cation at any time
without notice.
-40 to +70º CRelative 5 - 100%IP65
Dual Band Combiner TETRA / GSM90068 - 470 MHz / 870 - 970 MHz
Combines 2 RBSs into 1 antenna port
This dual band combiner enables the connec-tion of 2 Radio Base Stations to the combiner:
1 TETRA Radio Base Station1 GSM900 Radio Base Station
The combiner combines the 2 signals to the antenna port, or splits the signal to the 2 RBSs in the receiving direction.
This is a highly desirable function when designing shared antenna systems wishing to connect multiple RBSs to the shared antennas.
Reduces cost
By utilizing our dual band combiner you will reduce the cost of antennas, feeders and installation.
It eliminates the cost ineffi cient need to make one antenna installation for each system. By simply connecting the RBSs into the com-biner it will immediately render you all the benefi ts of antenna sharing.
TETR
ATE
TRA
GSM
900
GSM
900
ANTANT EGANTCELLULAR COMPONENTS
Egant Cellular ComponentsBox 945SE-114 79 StockholmSwedenPhone: +46 (0)8 620 06 50Fax: +46 (0)70 386 53 53E-mail: [email protected]
RevB
Technical Specifi cations for the Dual Band CombinerBelow are some typical data. For more detailed information, please contact us.
Electrical Specifi cationsProduct number:Passband:Port 1: TETRAPort 2: GSM900
Insertion loss:Port 1: TETRAPort 2: GSM900
Input return loss:Isolation between systems:
Max input power/port:Port 1: TETRAPort 2: GSM900Impedance in/out:
Intermodulation:IM3, 2 x 43 dBm:
EG 100 9015
68 - 470 MHz870 - 970 MHz
< 0.1 dB < 0.3 dB
> 18.0 dB> 50 dB
250 W250 W50 Ohm
< -117 dBm (160 dBc)
EG 100 9016
68 - 470 MHz870 - 970 MHz
< 0.1 dB < 0.3 dB
> 18.0 dB> 50 dB
250 W250 W50 Ohm
< -117 dBm (160 dBc)
EG 100 9017
68 - 470 MHz870 - 970 MHz
< 0.1 dB< 0.3 dB
> 18.0 dB> 50 dB
250 W250 W50 Ohm
< -117 dBm (160 dBc)
Mechanical Specifi cations Dimensions (W x H x D):Connectors:Weight:
128 x 177 x 28 mmN (f)2 kg
128 x 177 x 28 mm7/16 (f)2.6 kg
128 x 177 x 327/16 (f)2.8 kg
Environmental Specifi cations Temp. range (normal operation):Humidity:Sealing:
Egant reserves the right to change this product specifi cation at
any time without notice.
-40 to +70º CRelative 5 - 100%IP65
-40 to +70º CRelative 5 - 100%IP65
-40 to +70º CRelative 5 - 100%IP68
Dual Band Combiner68 - 500 MHz / 800 - 2500 MHz
Combines 2 RBSs into 1 Antenna Port
This dual band combiner enables the connec-tion of 2 Radio Base Stations to the combiner.
The combiner combines the 2 signals to1 antenna port, or splits the signal to the 2 RBSs in the receiving direction.
This is a highly desirable function when designing shared antenna systems wishing to connect multiple RBSs to the shared antennas.
Reduces cost
By utilizing our dual band combiner you will reduce the cost of antennas, feeders and installation.
It eliminates the cost ineffi cient need to make one antenna installation for each system. By simply connecting the RBSs into the com-biner it will immediately render you all the benefi ts of antenna sharing.
EGANTCELLULAR COMPONENTS
TETR
ATE
TRA
GSM
900
GSM
900
UM
TSU
MTS
ANT1ANT1
GSM
1800
GSM
1800
GSM
900
GSM
900
Egant Cellular ComponentsBox 945SE-114 79 StockholmSwedenPhone: +46 (0)8 620 06 50Fax: +46 (0)70 386 53 53E-mail: [email protected]
RevB
Technical Specifi cations for the Dual Band CombinerBelow are some typical data. For more detailed information, please contact us.
Electrical Specifi cationsProduct number:Passband:Port 1: Low bandPort 2: High band
Insertion loss:Port 1: Low band - ANTPort 2: High band - ANT
Input return loss:68 - 200 MHz200 - 380 MHz380 - 500 MHz
800 - 960 MHz1710 - 2500 MHz
Isolation between systems:Port 1: - ANTPort 2: - ANT
Max input power/port:Port 1: Low bandPort 2: High band
Intermodulation:IM3, 2 x 43 dBm:DC by-pass Port 2: UMTS - ANT
Impedance in/out:
EG 100 9034
68 - 500 MHz800 - 2500 MHz
< 0.2 dB < 0.2 dB
> 20.0 dB> 16.0 dB> 20.0 dB
> 20.0 dB> 20.0 dB
> 30 dB> 50 dB
< 300 W< 500 W
< -117 dBm (160 dBc)1A, max
50 Ohm
EG 602 0013
68 - 500 MHz800 - 2500 MHz
< 0.2 dB < 0.2 dB
> 20.0 dB> 16.0 dB> 20.0 dB
> 20.0 dB> 20.0 dB
> 30 dB> 50 dB
< 300 W< 500 W
< -117 dBm (160 dBc)1A, max
50 Ohm
Mechanical Specifi cationsDimensions (W x H x D):Connectors:Weight:
265 x 55 x 120 mm7/16 (f)1.5 kg
265 x 55 x 120 mmN (f)1.5 kg
Environmental Specifi cationsTemp. range (normal operation):Humidity:Sealing:
Egant reserves the right to change this product specifi cation at any time
without notice.
-30 to +70º CRelative 5 - 100%IP65
-30 to +70º CRelative 5 - 100%IP65
Dual Band Combiner W-LAN376 - 2500 MHz TETRA, GSM900, GSM1800, UMTS, W-LAN
Add W-LAN to your antenna system
Installing the dual band combiner W-LAN enables you to add W-LAN to your cellular antenna system. After installning the W-LAN combiner and an access point you are up and running with a high speed W-LAN system.
This is a highly important feature when de-signing shared antenna systems wishing to add W-LAN capability to your system.
Save money
The dual band combiner W-LAN offers addi-tional benefi ts by opening up W-LAN capa-bility to your existing antenna system.
The sleek and easily installed combiner has a broad-banded spectrum with low insertion loss and low intermodulation.
W-LA
NW
-LAN
Access point
Access point
376-2500MHz
376-2170MH
z
W-LA
NW
-LAN
InjectorInjector
W-LA
NW
-LAN
Access point
Access point
376-2500MHz
376-2170MH
z
W-LA
NW
-LAN
InjectorInjector
EGANTCELLULAR COMPONENTS
Egant Cellular ComponentsBox 945SE-114 79 StockholmSwedenPhone: +46 (0)8 620 06 50Fax: +46 (0)70 386 53 53E-mail: [email protected]
RevB
Technical Specifi cations for Dual Band Combiner W-LANBelow are some typical data. For more detailed information, please contact us.
Electrical Specifi cationsProduct number:Passband:Port 1:Port 2:Port 3:
Input return loss:68 - 2170 MHz:2400 - 2500 MHz:
Insertion loss:Port 2 - Port 1 (ANT):68 - 2170 MHz:Port 3 - Port 1 (ANT):2400 - 2500 MHz:
Isolation: Port 2 - Port 3, Port 3 - Port 2
Max input power/port:
3rd order intermodulation:IM3, 2 x 43 dBm:
Impedance in/out:
EG 100 9018
376 - 2170 MHz2400 - 2500 MHz
> 18 dB> 16 dB
< 1.0 dB (0.5 typ.) < 1.0 dB (0.5 typ.)
> 50 dB
50 W avg.0.5 kW peak
< - 97 dBm (140 dBc)
50 Ohm
EG 100 9028
376 - 2170 MHz2400 - 2500 MHz
> 18 dB> 16 dB
< 1.0 dB (0.5 typ.) < 1.0 dB (0.5 typ.)
> 50 dB
50 W avg.0.5 kW peak
< - 97 dBm (140 dBc)
50 Ohm
EG 602 0007
68 - 2500 MHz68 - 2170 MHz2400 - 2500 MHz
> 18 dB> 16 dB
< 1.0 dB (0.5 typ.) < 1.0 dB (0.5 typ.)
> 50 dB
50 W avg.0.5 kW peak
< - 97 dBm (140 dBc)
50 Ohm
Mechanical Specifi cationsDimensions (W x H x D):Connectors:Weight:
180 x 28 x 140 mmN (f)1.6 kg
180 x 32 x 140 mm7/16 (f)1.9 kg
180 x 32 x 140 mm7/16 (f), 7/16 (m), N (f)1.9 kg
Environmental Specifi cationsTemp. range (normal operation):Humidity:Sealing:
Egant reserves the right to change this product specifi cation at any time
without notice.
-35 to +70º CRelative 5 - 100%IP65
-35 to +70º CRelative 5 - 100%IP65
-35 to +70º CRelative 5 - 100%IP65
Dual Band Combiner376 - 500 MHz / 1920 - 2170 MHz
Combines 2 RBSs into 1 Antenna Port
This dual band combiner enables the connec-tion of 2 Radio Base Stations to the combiner.
The combiner combines the 2 signals to1 antenna port, or splits the signal to the 2 RBSs in the receiving direction.
This is a highly desirable function when designing shared antenna systems wishing to connect multiple RBSs to the shared antennas.
Reduces cost
By utilizing our dual band combiner you will reduce the cost of antennas, feeders and installation.
It eliminates the cost ineffi cient need to make one antenna installation for each system. By simply connecting the RBSs into the com-biner it will immediately render you all the benefi ts of antenna sharing.
EGANTCELLULAR COMPONENTS
TETR
ATE
TRA
UM
TSU
MTS
ANTANT
Egant Cellular ComponentsBox 945SE-114 79 StockholmSwedenPhone: +46 (0)8 620 06 50Fax: +46 (0)70 386 53 53E-mail: [email protected]
RevB
Technical Specifi cations for the Dual Band CombinerBelow are some typical data. For more detailed information, please contact us.
Electrical Specifi cationsProduct number:Passband:Port 1: Low bandPort 2: High band
Insertion loss:Port 1: Low band - ANTPort 2: High band - ANT
Input return loss:376 - 500 MHz1920 - 2170 MHz
Isolation between systems:Port 1: - ANTPort 2: - ANT
Max input power/port:Port 1: Low bandPort 2: High band
Intermodulation:IM3, 2 x 43 dBm:DC by-pass Port 2: UMTS - ANT
Impedance in/out:
EG 602 0045
376 - 500 MHz1920 - 2170 MHz
< 0.3 dB < 0.3 dB
> 18.0 dB> 18.0 dB
> 30 dB> 50 dB
< 300 W< 500 W
< -117 dBm (160 dBc)1A, max
50 Ohm
EG 602 0046
376 - 500 MHz1920 - 2170 MHz
< 0.3 dB < 0.3 dB
> 18.0 dB> 18.0 dB
> 30 dB> 50 dB
< 300 W< 500 W
< -117 dBm (160 dBc)1A, max
50 Ohm
Mechanical Specifi cationsDimensions (W x H x D):Connectors:Weight:
242 x 31 x 84 mmN (f)1.5 kg
242 x 31 x 84 mm7/16 (f)1.5 kg
Environmental Specifi cationsTemp. range (normal operation):Humidity:Sealing:
Egant reserves the right to change this product specifi cation at any time
without notice.
-30 to +70º CRelative 5 - 100%IP65
-30 to +70º CRelative 5 - 100%IP65
Dual Band Combiner FM + VHF + DAB / TETRA 88 - 240 MHz / 376 - 480 MHz
Combines FM + VHF + DAB and TETRAinto one antenna port
This dual band combiner enables the connec-tion of these two systems to the combiner:
1 FM + VHF + DAB Input1 TETRA Radio Base Station
The combiner combines the two signals intoone antenna port, or splits the signal into the two input systems in the receiving direction.
Reduces cost
By utilizing our dual band combiner you will reduce the cost of antennas, feeders and installation.
It eliminates the cost ineffi cient need to make one antenna installation for each system. By simply connecting the inputs into the com-biner it will immediately render you all the benefi ts of antenna sharing.
EGANTCELLULAR COMPONENTS
Egant Cellular ComponentsBox 945SE-114 79 StockholmSwedenPhone: +46 (0)8 620 06 50Fax: +46 (0)70 386 53 53E-mail: [email protected]
RevC
Technical Specifi cations for the FM + VHF + DAB / TETRA Dual Band CombinerBelow are some typical data. For more detailed information, please contact us.
Electrical Specifi cationsProduct number:Passband:Port 1: FM + VHF + DABPort 2: TETRA
Insertion loss:Port 1: 88 - 108 MHzPort 1: 108 - 174 MHzPort 1: 174 - 240 MHzPort 2: TETRA
Input return loss:
Isolation between systems: Port 1 - 2: 88 - 108 MHz, 108 - 240 MHz Port 2 - 1: 376 - 480 MHz
Max input power/port:Port 1: Port 2:Impedance in/out:DC-Bypass
EG 602 0029
88 - 240 MHz376 - 480 MHz
< 0.3 dB < 0.3 dB < 0.5 dB < 0.5 dB
> 18.0 dB
> 50 dB> 50 dB
< 100 W< 100 W50 Ohm Port 1 - Ant
EG 602 0030
88 - 240 MHz376 - 480 MHz
< 0.5 dB < 0.5 dB< 0.5 dB< 0.5 dB
> 18.0 dB
> 40 dB> 40 dB
< 20 W< 20 W50 Ohm Port1 - Ant
EG 602 0038
88 - 240 MHz376 - 480 MHz
< 0.5 dB < 0.5 dB< 0.5 dB< 0.5 dB
> 18.0 dB
> 40 dB> 40 dB
< 20 W< 20 W50 Ohm Port1 - Ant
Mechanical & Environmental Specifi cations Dimensions (W x H x D):Connectors:Weight:Sealing:
Egant reserves the right to change this product specifi cation at any time without notice.
250 x 80 x 37 mm7/16 (f)2.9 kgIP67
118 x 119 x 37 mm7/16 (f)1.7 kgIP67
110 x 115 x 37 mm7/16 (f)1.4 kgIndoor use
Dual Band Combiner 380 - 395 MHz / 410 - 425 MHzTETRA Public SafetyTETRA Public Services
Combines 2 RBSs into 1 Antenna Port
This Dual Band Combiner enables the connec-tion of 2 Radio Base Stations to the combiner:
1 TETRA Public Safety System1 TETRA Public Services System
The Combiner combines the 2 signals to 1 antenna port, or splits the signal to the 2 RBSs in the receiving direction.
This is a highly desirable function when designing shared antenna systems wishing to connect multiple RBSs to the shared antennas.
Reduces cost
By utilizing the Egant Dual Band Combiner you will reduce the cost of antennas, feeders and installation.
It eliminates the cost ineffi cient need to to make one antenna installation for each sys-tem. By simply connecting the RBSs into the combiner it will immediately render you all the benefi ts of antenna sharing.
EGANTCELLULAR COMPONENTS
PRELIMINARY
Egant Cellular ComponentsBox 945SE-114 79 StockholmSwedenPhone: +46 (0)8 620 06 50Fax: +46 (0)70 386 53 53E-mail: [email protected]
RevA
Technical Specifi cations for the Dual Band CombinerBelow are some typical data. For more detailed information, please contact us.
Electrical Specifi cationsProduct number: Passband:Port 1: TETRA - Public SafetyPort 2: TETRA - Public Services
Insertion loss:Port 1: TETRA - Public SafetyPort 2: TETRA - Public Services
Input return loss:Isolation between systems:
Max input power/port:Port 1: GSM900Port 2: GSM1800 / UMTS
Impedance in/out:
Intermodulation:IM3, 2 x 43 dBm:
EG 602 0023
380 - 395 MHz410 - 425 MHz
< 1.2 dB < 1.2 dB
> 18.0 dB> 65 dB
< 60W< 60W
50 Ohm
< -117 dBm (160 dBc)
EG 602 0024
380 - 395 MHz410 - 425 MHz
< 1.2 dB < 1.2 dB
> 18.0 dB> 65 dB
< 60W< 60W
50 Ohm
< -117 dBm (160 dBc)
Mechanical Specifi cationsDimensions (W x H x D):Connectors:Weight:
150 x 150 x 110 mmN (f)2.5 kg
150 x 150 x 110 mm7/16 (f)2.5 kg
Environmental Specifi cationsTemp. range (normal operation):Sealing:
Egant reserves the right to change this product specifi cation at any time
without notice.
-40 to +70º CIndoor
-40 to +70º CIndoor
Dual Band Combiner 380 - 395 MHz / 410 - 425 MHzTETRA Public SafetyTETRA Public Services
Combines 2 RBSs into 1 Antenna Port
This Dual Band Combiner enables the connec-tion of 2 Radio Base Stations to the combiner:
1 TETRA Public Safety System1 TETRA Public Services System
The Combiner combines the 2 signals to 1 antenna port, or splits the signal to the 2 RBSs in the receiving direction.
This is a highly desirable function when designing shared antenna systems wishing to connect multiple RBSs to the shared antennas.
Reduces cost
By utilizing the Egant Dual Band Combiner you will reduce the cost of antennas, feeders and installation.
It eliminates the cost ineffi cient need to to make one antenna installation for each sys-tem. By simply connecting the RBSs into the combiner it will immediately render you all the benefi ts of antenna sharing.
EGANTCELLULAR COMPONENTS
PRELIMINARY
Egant Cellular ComponentsBox 945SE-114 79 StockholmSwedenPhone: +46 (0)8 620 06 50Fax: +46 (0)70 386 53 53E-mail: [email protected]
RevA
Technical Specifi cations for the Dual Band CombinerBelow are some typical data. For more detailed information, please contact us.
Electrical Specifi cationsProduct number: Passband:Port 1: TETRA - Public SafetyPort 2: TETRA - Public Services
Insertion loss:Port 1: TETRA - Public SafetyPort 2: TETRA - Public Services
Input return loss:Isolation between systems:
Max input power/port:Port 1: TETRA - Public SafetyPort 2: TETRA - Public Services
Impedance in/out:
Intermodulation:IM3, 2 x 43 dBm:
EG 602 0023
380 - 395 MHz410 - 425 MHz
< 1.2 dB < 1.2 dB
> 18.0 dB> 50 dB
< 60W< 60W
50 Ohm
< -117 dBm (160 dBc)
EG 602 0024
380 - 395 MHz410 - 425 MHz
< 1.2 dB < 1.2 dB
> 18.0 dB> 50 dB
< 60W< 60W
50 Ohm
< -117 dBm (160 dBc)
Mechanical Specifi cationsDimensions (W x H x D):Connectors:Weight:
150 x 150 x 110 mmN (f)2.5 kg
150 x 150 x 110 mm7/16 (f)2.5 kg
Environmental Specifi cationsTemp. range (normal operation):Sealing:
Egant reserves the right to change this product specifi cation at any time
without notice.
-40 to +70º CIndoor
-40 to +70º CIndoor
Duplexer TETRA380 - 385 MHz390 - 395 MHz
EGANTCELLULAR COMPONENTS
PRELIMINARY
This Duplexer combines/splits the TETRA Tx and Rx signals to or from one common Tx/Rx antenna.
Egant Cellular ComponentsBox 945SE-114 79 StockholmSwedenPhone: +46 (0)8 620 06 50Fax: +46 (0)70 386 53 53E-mail: [email protected]
RevA
Technical Specifi cations for the Duplexer TETRABelow are some typical data. For more detailed information, please contact us.
Electrical Specifi cationsProduct number: Passband:Port 1: RXPort 2: TX
Insertion loss:
Input return loss:Isolation between TX/RX:
Max input power/port:
Impedance in/out:
Intermodulation:IM3, 2 x 43 dBm:
EG 602 0020
380 - 385 MHz390 - 395 MHz
< 1.5 dB
> 20.0 dB> 65 dB
200 W
50 Ohm
< -117 dBm (160 dBc)
EG 602 0021
380 - 385 MHz390 - 395 MHz
< 0.8 dB
> 20.0 dB> 65 dB
200 W
50 Ohm
< -117 dBm (160 dBc)
Mechanical Specifi cationsDimensions (W x H x D):Connectors:Weight:
100 x 150 x 100 mm7/16 (f)1.4 kg
100 x 250 x 300 mm7/16 (f)4.2 kg
Environmental Specifi cationsTemp. range (normal operation):Humidity:Sealing:
Egant reserves the right to change this product specifi cation at any time
without notice.
-40 to +70º CRelative 5 - 100%Indoor use
-40 to +70º CRelative 5 - 100%Indoor use
Duplexer TETRA380 - 385 MHz390 - 395 MHz415 - 420 MHz425 - 430 MHz
EGANTCELLULAR COMPONENTS
PRELIMINARY
This Duplexer combines/splits the TETRA TX and RX signals to or from one common TX/RX antenna.
Egant Cellular ComponentsBox 945SE-114 79 StockholmSwedenPhone: +46 (0)8 620 06 50Fax: +46 (0)70 386 53 53E-mail: [email protected]
RevP1A
Technical Specifi cations for TETRA DuplexersBelow are some typical data. For more detailed information, please contact us.
Electrical Specifi cationsProduct number: Passband:Port 1: RXPort 2: TX
Insertion loss:
Input return loss:Isolation between TX/RX:
Max input power/port:
Impedance in/out:
Intermodulation:IM3, 2 x 43 dBm:
Monitoring port:
EG 602 0020
380 - 385 MHz390 - 395 MHz
< 1.5 dB
> 20.0 dB> 65 dB
200 W
50 Ohm
< -117 dBm (160 dBc)
EG 602 0021
380 - 385 MHz390 - 395 MHz
< 0.8 dB
> 20.0 dB> 65 dB
200 W
50 Ohm
< -117 dBm (160 dBc)
EG 602 0037
415 - 420 MHz425 - 430 MHz
< 1.9 dB (1.2 typ)
> 20.0 dB> 75 dB
80 W
50 Ohm
< -117 dBm (160 dBc)
20 dB
Mechanical Specifi cationsDimensions (W x H x D):Connectors:Weight:
100 x 150 x 100 mm7/16 (f)1.4 kg
100 x 250 x 300 mm7/16 (f)4.2 kg
240 x 240 x 80 mmSMA3 kg
Environmental Specifi cationsTemp. range (normal operation):Humidity:Sealing:
Egant reserves the right to change this product
specifi cation at any time without notice.
-40 to +70º CRelative 5 - 100%Indoor use
-40 to +70º CRelative 5 - 100%Indoor use
-10 to +60º CRelative 5 - 100%Indoor use
Phase Adjuster / DuplexerGSM 900
EGANTCELLULAR COMPONENTS
Egant Cellular ComponentsBox 945SE-114 79 StockholmSwedenPhone: +46 (0)8 620 06 50Fax: +46 (0)70 386 53 53E-mail: [email protected]
RevC
Technical Specifi cations for the Phase Adjuster/DuplexerBelow are some typical data. For more detailed information, please contact us.
Electrical Specifi cationsProduct number:Passband:Insertion loss:Port 1 - Ant 1: 890 - 915 MHzPort 1 - Ant 2: 890 - 915 MHzPort 2 - Ant 1: 935 - 960 MHzPort 2 - Ant 2: 935 - 960 MHz
Phase difference:Port 1 - Ant 1: 890 - 915 MHzPort 1 - Ant 2: 890 - 915 MHzPort 1 - Ant 1: 935 - 960 MHzPort 1 - Ant 2: 935 - 960 MHzPort 2 - Ant 1: 935 - 960 MHzPort 2 - Ant 2: 935 - 960 MHz
EG 100 9032890 - 915, 935 - 960 MHz
< 1.5 dB (0.9 dB typ)< 1.5 dB (0.9 dB typ)< 7.8 dB (7.1 dB typ 6 dB coupling)< 7.8 dB (7.1 dB typ 6 dB coupling)
0°0°- 90 + 3° (+ 1° typ)- 90 + 3° (+ 1° typ)0 + 3° (+ 1° typ)0 + 3° (+ 1° typ)
Input return loss:Isolation between UL - DL:Max input power/port:Impedance in/out:
Mechanical Specifi cationsDimensions (W x H x D):Connectors:Weight:
> 18.0 dB> 30 dB2 x 35 W50 Ohm
105 x 240 x 165 mm7/16 (f)3.7 kg
Environmental Specifi cationsTemp. range (normal operation):Humidity:Sealing:
Egant reserves the right to change this product specifi cation at any time without notice.
-30 to +70º CRelative 5 - 100%IP68
3 dB Combiner, Broad Band 376 - 960 MHzTETRA, GSM900
Combines up to 2 repeaters or RBSs into the same antenna system
The 3 dB combiner enables the connection of 2 repeaters or radio base stations. The com-biner combines the signal and equally splits the signals between the antenna ports. This is a highly desirable function when design-ing shared antenna systems wishing to con-nect multiple repeaters or RBSs to the shared antennas.
Innovative design
The 3 dB combiner is designed for low inser-tion loss and low intermodulation.There is no need for terminations or attenua-tors, which results in very low insertion loss and outstanding intermodulation perfomance.
The benefi ts from installing the 3 dB combiner instead of hybrid combiners and splitters are:
· Lower insertion loss· Fewer system components· Superior antenna isolation· Greater system quality· Cost effective design improvement
RBS 2RBS 2RBS 1RBS 1
ANT1 ANT2ANT1 ANT2
EG 699 0006Bracket for EGANT Cellular Componentscombiner.
EGANTCELLULAR COMPONENTS
Egant Cellular ComponentsBox 945SE-114 79 StockholmSwedenPhone: +46 (0)8 620 06 50Fax: +46 (0)70 386 53 53E-mail: [email protected]
RevB
Technical Specifi cations for the 3 dB CombinerBelow are some typical data. For more detailed information, please contact us.
Electrical Specifi cationsProduct number:Passband:
Isolation between ports:Input return loss:Coupling:Max input power/port:3rd order intermodulation:IM3, 2 x 43 dBm:Impedance in/out:
EG 500 8017376 - 500 MHz, 880 - 960 MHz
> 26 dB (typ 30 dB)> 20.0 dB3.1 + 0.2 dB120 W
< - 97 dBm50 Ohm
EG 500 8018376 - 500 MHz, 880 - 960 MHz
> 26 dB (typ 30 dB)> 20.0 dB3.1 + 0.2 dB120 W
< - 97 dBm50 Ohm
Mechanical Specifi cationsDimensions (W x H x D):Connectors:
190 x 25 x 82 mmN (f)
190 x 42 x 82 mm7/16 (f)
Environmental Specifi cationsTemp. range (normal operation):Humidity:Sealing:
Egant reserves the right to change this product specifi cation at any time without notice.
-30 to +70º CRelative 5 - 100%IP65
-30 to +70º CRelative 5 - 100%IP65
In 1
In 2
Out 1 + 2
Out 1 + 2
3 dB Combiner, Broad Band 376 - 2200 MHzTETRA, GSM900, GSM1800, UMTS
Combines up to 2 repeaters or RBSs into the same antenna system
The 3 dB combiner enables the connection of 2 repeaters or radio base stations. The com-biner combines the signal and equally splits the signals between the antenna ports. This is a highly important function when designing shared antenna systems wishing to connect multiple repeaters or RBSs to the shared antennas.
Innovative design
The 3dB combiner incorporates a broad band and low loss design. It is specifi cally designed with low insertion loss and intermodulation in mind. There is no need for terminations or attenuators, which results in very low inser-tion loss and outstanding intermodulation performance.
The benefi ts from installing the 3 dB combiner instead of power splitters are:
· Lower insertion loss· Fewer system components· Superior antenna isolation· Greater system quality· Cost effective design improvement
RBS 2RBS 2RBS 1RBS 1
ANT1 ANT2ANT1 ANT2
EGANTCELLULAR COMPONENTS
Egant Cellular ComponentsBox 945SE-114 79 StockholmSwedenPhone: +46 (0)8 620 06 50Fax: +46 (0)70 386 53 53E-mail: [email protected]
Rev A
Technical Specifi cations for the 3 dB CombinerBelow are some typical data. For more detailed information, please contact us.
Electrical Specifi cationsProduct number:Passband:
Isolation between ports:376 - 1500 MHz:1500 - 2200 MHz:
Input return loss:376 - 1500 MHz1500 - 2200 MHzCoupling:Max input power/port:
3rd order intermodulation:IM3, 2 x 43 dBm:Impedance in/out:
EG 603 0030376 - 2200 MHz
> 25 dB (typ 30 dB)> 20 dB (typ 25 dB)
> 20.0 dB> 18.0 dB3.1 + 0.2 dB200 W
< - 97 dBm50 Ohm
EG 603 0031376 - 2200 MHz
> 25 dB (typ 30 dB)> 20 dB (typ 25 dB)
> 20.0 dB> 18.0 dB3.1 + 0.2 dB200 W
< - 97 dBm50 Ohm
Mechanical Specifi cationsDimensions (W x H x D):Connectors:
215 x 26 x 115 mmN (f)
215 x 26 x 115 mm7/16 (f)
Environmental Specifi cationsTemp. range (normal operation):Humidity:Sealing:
Egant reserves the right to change this product specifi cation at any time without notice.
-30 to +70º CRelative 5 - 100%IP65
-30 to +70º CRelative 5 - 100%IP65
3 dB Combiner, Broad Band 700 - 2700 MHzGSM, TDMA, UMTS, W-LAN
Combines up to 2 repeaters or RBSs into the same antenna system
The 3 dB combiner enables the connection of 2 repeaters or radio base stations. The com-biner combines the signal and equally splits the signals between the antenna ports. This is a highly important function when designing shared antenna systems wishing to connect multiple repeaters or RBSs to the shared antennas.
Innovative design
The 3 dB combiner incorporates a broad band and low loss design. It is specifi cally designed with low insertion loss and intermodulation in mind. There is no need for terminations or attenuators, which results in very low inser-tion loss and outstanding intermodulation performance.
The benefi ts from installing the 3 dB combiner instead of power splitters are:
· Lower insertion loss· Fewer system components· Superior antenna isolation· Greater system quality· Cost effective design improvement
RBS 1RBS 1RBS 2RBS 2
ANT1 ANT2ANT1 ANT2
EGANTCELLULAR COMPONENTS
Egant Cellular ComponentsBox 945SE-114 79 StockholmSwedenPhone: +46 (0)8 62 00 650Fax: +46 (0)70 386 53 53E-mail: [email protected]
RevB
Technical Specifi cations for the 3 dB CombinerBelow are some typical data. For more detailed information, please contact us.
Electrical Specifi cationsProduct number:Passband:
Isolation between ports:Input return loss:Coupling:Max input power/port:3rd order intermodulation:IM3, 2 x 43 dBm:Impedance in/out:
EG 500 8010700 - 2700 MHz
> 30 dB > 22.0 dB3.1 + 0.3 dB240 W
< - 117 dBm, 160 dBc50 Ohm
EG 500 8011700 - 2700 MHz
> 30 dB > 22.0 dB3.1 + 0.3 dB240 W
< - 117 dBm, 160 dBc50 Ohm
Mechanical Specifi cationsDimensions (W x H x D):Connectors:
135 x 45 x 80 mm7/16 (f)
135 x 45 x 80 mmN (f)
Environmental Specifi cationsTemp. range (normal operation):Humidity:Sealing:
Egant reserves the right to change this product specifi cation at any time without notice.
-30 to +70º CRelative 5 - 100%IP65
-30 to +70º CRelative 5 - 100%IP65
In 1
In 2
Out 1 + 2
Out 1 + 2
3 dB Combiner68 - 79 MHz
Combines up to 2 repeaters or RBSs into the same antenna system
The 3 dB combiner enables the connection of 2 repeaters or radio base stations. The com-biner combines the signal and equally splits the signals between the antenna ports. This is a highly important function when designing shared antenna systems wishing to connect multiple repeaters or RBSs to the shared antennas.
The benefi ts from installing the 3 dB combiner instead of power splitters are:
· Lower insertion loss· Fewer system components· Superior antenna isolation· Greater system quality· Cost effective design improvement
Innovative design
The 3 dB combiner incorporates a broad band and low loss design. It is specifi cally designed with low insertion loss and intermodulation in mind. There is no need for terminations or attenuators, which results in very low inser-tion loss and outstanding intermodulation performance.
EG 699 0006
Bracket for EGANT Cellular Components combiner.
RBS 1RBS 1RBS 2RBS 2
ANT1 ANT2ANT1 ANT2
EGANTCELLULAR COMPONENTS
Egant Cellular ComponentsBox 945SE-114 79 StockholmSwedenPhone: +46 (0)8 620 06 50Fax: +46 (0)70 386 53 53E-mail: [email protected]
RevB
Technical Specifi cations for the 3 dB CombinerBelow are some typical data. For more detailed information, please contact us.
Electrical Specifi cationsProduct number:Passband:
Isolation between ports:
Input return loss:
Coupling:
Max input power/port:
3rd order intermodulation:IM3, 2 x 43 dBm:
Impedance in/out:
EG 603 000168 - 79 MHz
> 30 dB
> 20.0 dB
3.1 + 0.2 dB
120 W
< - 97 dBm, 140 dBc
50 Ohm
Mechanical Specifi cations Dimensions (W x H x D):Connectors:
190 x 25 x 82 mmN (f)
Environmental Specifi cationsTemp. range (normal operation):Humidity:Sealing:
-30 to +70º CRelative 5 - 100%IP65
Installation bracket:Material:
EG 699 0006Aluminum Zinc
Egant reserves the right to change this product specifi cation at any time without notice.
In 1 In 2
Out 1 + 2 Out 1 + 2
2-Way Combiner 376 - 500 MHz800 - 2170 MHzTETRA, GSM900, GSM1800, DCS, UMTS
Combining with optimization
Do you have radio base stations orrepeaters in separate locations? Egant has the solution. Our 2-way combiner enables you to optimize your system by compensating for the added cable loss in addition to combining the signals into one point with equal power, add-ing control over signal strength to the antenna.
Innovative design
This 2-way combiner incorporates a broad band and low loss product design. It is de-signed for low insertion loss and intermodula-tion.
The benefi ts from installing the 2-way combiner are:
· Higher antenna isolation· Lower insertion loss· Fewer system components· Higher system quality· Cost-effective design improvement
RBS 2RBS 2RBS 1RBS 1
ANTANT
Cable lossCable loss 100%
4.7 dB3dB, 50%
EGANTCELLULAR COMPONENTS
Egant Cellular ComponentsBox 945SE-114 79 StockholmSwedenPhone: +46 (0)8 620 06 50Fax: +46 (0)70 386 53 53E-mail: [email protected]
RevC
Technical Specifi cations for the 2-Way Combiner Below are some typical data. For more detailed information, please contact us.
Electrical Specifi cationsProduct number:Passband:
Isolation between ports:Input return loss:Coupling in 1 - out:Coupling in 2 - out:
Max input power/port:3rd order intermodulation:IM3, 2 x 43 dBm:
Impedance in/out:
EG 100 9204800 - 2170 MHz
> 30 dB> 20.0 dB1.8 + 0.3 dB4.7 + 0.3 dB
500 W
< - 120 dBm, 163 dBc50 Ohm
EG 100 9206800 - 2170 MHz
> 30 dB> 20.0 dB1.2 + 0.3 dB6.0 + 0.3 dB
500 W
< - 120 dBm, 163 dBc50 Ohm
EG 100 9207800 - 2170 MHz
> 30 dB> 20.0 dB1.1 + 0.15 dB7.0 + 0.15 dB
500 W
< - 120 dBm, 163 dBc50 Ohm
EG 100 9210800 - 2170 MHz
> 30 dB> 20.0 dB1.0 + 0.3 dB10.0 + 0.3 dB
500 W
< - 120 dBm, 163 dBc50 Ohm
Mechanical Specifi cationsDimensions (W x H x D):Connectors:
140 x 80 x 40 mmN (f)
140 x 80 x 40 mmN (f)
140 x 80 x 40 mmN (f)
140 x 80 x 40 mmN (f)
Environmental Specifi cationsTemp. range (normal operation):Humidity:Sealing:
-30 to +70º CRelative 5 - 100%IP68
-30 to +70º CRelative 5 - 100%IP68
-30 to +70º CRelative 5 - 100%IP68
-30 to +70º CRelative 5 - 100%IP68
Electrical Specifi cationsProduct number:Passband:
Isolation between ports:Input return loss:Coupling in 1 - out:Coupling in 2 - out:
Max input power/port:3rd order intermodulation:IM3, 2 x 43 dBm:
Impedance in/out:
EG 100 9304376 - 500 MHz
> 30 dB> 20.0 dB1.8 + 0.2 dB4.7 + 0.4 dB
500 W
< - 120 dBm, 163 dBc50 Ohm
EG 100 9306376 - 500 MHz
> 30 dB> 20.0 dB1.2 + 0.2 dB6.0 + 0.4 dB
500 W
< - 120 dBm, 163 dBc50 Ohm
EG 100 9307376 - 500 MHz
> 30 dB> 20.0 dB1.1 + 0.2 dB7.0 + 0.4 dB
500 W
< - 120 dBm, 163 dBc50 Ohm
EG 100 9310376 - 500 MHz
> 30 dB> 20.0 dB1.0 + 0.2 dB10.0 + 0.4 dB
500 W
< - 120 dBm, 163 dBc50 Ohm
Mechanical Specifi cationsDimensions (W x H x D):Connectors:
140 x 80 x 40 mmN (f)
140 x 80 x 40 mmN (f)
140 x 80 x 40 mmN (f)
140 x 80 x 40 mmN (f)
Environmental Specifi cationsTemp. range (normal operation):Humidity:Sealing:
-30 to +70º CRelative 5 - 100%IP65
-30 to +70º CRelative 5 - 100%IP65
-30 to +70º CRelative 5 - 100%IP65
-30 to +70º CRelative 5 - 100%IP65
Installation supportInstallation bracket: EG 699 0007
Egant reserves the right to change this product
specifi cation at any time without notice.
(Order separately)
2-Way Combiner 376 - 500 MHz800 - 2170 MHzTETRA, GSM900, GSM1800, DCS, UMTS
Combining with optimization
Do you have radio base stations orrepeaters in separate locations? Egant has the solution. Our 2-way combiner enables you to optimize your system by compensating for the added cable loss in addition to combining the signals into one point with equal power, add-ing control over signal strength to the antenna.
Innovative design
This 2-way combiner incorporates a broad band and low loss product design. It is de-signed for low insertion loss and intermodula-tion.
The benefi ts from installing the 2-way combiner are:
· Higher antenna isolation· Lower insertion loss· Fewer system components· Higher system quality· Cost-effective design improvement
RBS 2RBS 2RBS 1RBS 1
ANTANT
Cable lossCable loss 100%
4.7 dB3 dB, 50%
EGANTCELLULAR COMPONENTS
Egant Cellular ComponentsBox 945SE-114 79 StockholmSwedenPhone: +46 (0)8 620 06 50Fax: +46 (0)70 386 53 53E-mail: [email protected]
RevB
Technical Specifi cations for the 2-Way Combiner Below are some typical data. For more detailed information, please contact us.
Electrical Specifi cationsProduct number:Passband:
Isolation between ports:Input return loss:Coupling in 1 - out:Coupling in 2 - out:
Max input power/port:3rd order intermodulation:IM3, 2 x 43 dBm:
Impedance in/out:
EG 100 9004800 - 2170 MHz
> 30 dB> 20.0 dB1.8 + 0.3 dB4.7 + 0.3 dB
70 W
< - 120 dBm, 163 dBc
50 Ohm
EG 100 9006800 - 2170 MHz
> 30 dB> 20.0 dB1.2 + 0.3 dB6.0 + 0.3 dB
70 W
< - 120 dBm, 163 dBc
50 Ohm
EG 100 9010800 - 2170 MHz
> 30 dB> 20.0 dB1.0 + 0.3 dB10.0 + 0.3 dB
70 W
< - 120 dBm, 163 dBc
50 Ohm
Mechanical Specifi cationsDimensions (W x H x D):Connectors:
140 x 80 x 40 mm7/16 (f)
140 x 80 x 40 mm7/16 (f)
140 x 80 x 40 mm7/16 (f)
Environmental Specifi cationsTemp. range (normal operation):Humidity:Sealing:
-30 to +70º CRelative 5 - 100%IP68
-30 to +70º CRelative 5 - 100%IP68
-30 to +70º CRelative 5 - 100%IP68
Electrical Specifi cationsProduct number:Passband:
Isolation between ports:Input return loss:Coupling in 1 - out:Coupling in 2 - out:
Max input power/port:3rd order intermodulation:IM3, 2 x 43 dBm:
Impedance in/out:
EG 100 9104376 - 500 MHz
> 30 dB> 20.0 dB1.8 + 0.15 dB4.7 + 0.15 dB
70 W
< - 120 dBm, 163 dBc
50 Ohm
EG 100 9106376 - 500 MHz
> 30 dB> 20.0 dB1.2 + 0.15 dB6.0 + 0.15 dB
70 W
< - 120 dBm, 163 dBc
50 Ohm
EG 100 9110376 - 500 MHz
> 30 dB> 20.0 dB1.0 + 0.15 dB10.0 + 0.15 dB
70 W
< - 120 dBm, 163 dBc
50 Ohm
Mechanical Specifi cationsDimensions (W x H x D):Connectors:
140 x 80 x 40 mm7/16 (f)
140 x 80 x 40 mm7/16 (f)
140 x 80 x 40 mm7/16 (f)
Environmental Specifi cationsTemp. range (normal operation):Humidity:Sealing:
-30 to +70º CRelative 5 - 100%IP68
-30 to +70º CRelative 5 - 100%IP68
-30 to +70º CRelative 5 - 100%IP68
Installation supportInstallation bracket: EG 699 0007 (Order separately)
Egant reserves the right to change this product specifi cation at any time without notice.
3x3 Combiner 4.8dB700 - 2700 MHz
Combines up to 3 RBSs into the same antenna system
The 3x3 combiner enables the connection of 3 Radio Base Stations to the combiner. The com-biner combines the signal and equally splits the signals between the antenna ports.
This is a highly important function when designing shared antenna systems wishing to connect multiple RBSs to the shared antennas.
Innovative design
The 3x3 combiner is a broad band and low loss product design. It is intentionally de-signed for low insertion loss and lowintermodulation.
The benefi ts of using our 3x3 combiner are:· Lower insertion loss· Fewer system components· Superior antenna isolation· Greater system quality· Cost effective design improvement
EGANTCELLULAR COMPONENTS
Egant Cellular ComponentsBox 945SE-114 79 StockholmSwedenPhone: +46 (0)8 62 00 650Fax: +46 (0)70 386 53 53E-mail: [email protected]
Technical Specifi cations for the 3x3 CombinerBelow are some typical data. For more detailed information, please contact us.
Electrical Specifi cationsProduct number:Passband:
Coupling: (700 - 2200 MHz)Coupling: (2200 - 2700 MHz)
Input return loss:Isolation between ports:Intermodulation 2 x 43 dBm:
Max input power/port:Max peak power:
Impedance in/out:
EG 603 0039700 - 2700 MHz
5.0 +/- 0.8 dB5.3 +/- 1.3 dB
> 20.0 dB> 25 dB (30 dB typ.)< 107 dBm (150 dBc)
60 W3 kW
50 Ohm
EG 603 0040700 - 2700 MHz
5.0 +/- 0.8 dB5.3 +/- 1.3 dB
> 20.0 dB> 23 dB (28 dB typ.)< 107 dBm (150 dBc)
60 W3 kW
50 Ohm
Mechanical Specifi cationsDimensions (W x H x D):Connectors:Weight:
204 x 32 x 140 mm7/16 (f)1.6 kg
204 x 25 x 140 mmN (f)1.4 kg
Environmental Specifi cationsTemp. range (normal operation):Humidity:Sealing:
Egant reserves the right to change this product specifi cation at any time without notice.
-35 to +65º CRelative 5 - 100%IP67
-35 to +65º CRelative 5 - 100%IP67
RevA
2-Way Combiner 800 - 2170 MHzGSM 900, GSM 1800, PCS, UMTS
Combining with optimization
Do you have radio base stations orrepeaters in separate locations? Egant has the solution. Our 2-way combiner enables you to optimize your system by compensating for the added cable loss in addition to combining the signals into one point with equal power, add-ing control over signal strength to the antenna.
Innovative design
This 2-way combiner incorporates a broad band and low loss product design. It is de-signed for low insertion loss and intermodula-tion.
The benefi ts from installing the 2-way combiner are:
· Higher antenna isolation· Lower insertion loss· Fewer system components· Higher system quality· Cost-effective design improvement
RBS 2RBS 2RBS 1RBS 1
ANTANT
Cable lossCable loss 100%
4.7dB3dB, 50%
EGANTCELLULAR COMPONENTS
Egant Cellular ComponentsBox 945SE-114 79 StockholmSwedenPhone: +46 (0)8 620 06 50Fax: +46 (0)70 386 53 53E-mail: [email protected]
RevB
Technical Specifi cations for the 2-Way Combiner Below are some typical data. For more detailed information, please contact us.
Electrical Specifi cationsProduct number:Passband:
Isolation between ports J2 - J3:Input return loss:Coupling J1 - J2:Coupling J1 - J3:
Max input power/port:
3rd order intermodulation:IM3, 2 x 43 dBm:
Impedance in/out:
EG 603 0011800 - 2170 MHz
> 30 dB> 20.0 dB1.8 + 0.3 dB4.7 + 0.3 dB
70 W
< - 120 dBm,163 dBc50 Ohm
EG 603 0012800 - 2170 MHz
> 30 dB> 20.0 dB1.2 + 0.3 dB6.0 + 0.3 dB
70 W
< - 120 dBm, 163 dBc50 Ohm
EG 603 0013800 - 2170 MHz
> 30 dB> 20.0 dB1.0 + 0.3 dB10.0 + 0.3 dB
70 W
< - 120 dBm, 163 dBc50 Ohm
Mechanical Specifi cationsDimensions (W x H x D):Connectors:J1:J2:J3 - J4 (coupled port):
140 x 80 x 40 mm
7/16 (m)7/16 (f)N (f)
140 x 80 x 40 mm
7/16 (m) 7/16 (f)N (f)
140 x 80 x 40 mm
7/16 (m)7/16 (f)N (f)
Environmental Specifi cationsTemp. range (normal operation):Humidity:Sealing:
-30 to +70º CRelative 5 - 100%IP65
-30 to +70º CRelative 5 - 100%IP65
-30 to +70º CRelative 5 - 100%IP65
Installation supportInstallation bracket: EG 699 0007
Egant reserves the right to change this product specifi cation at any time without notice.
(Order separately)
J2, 7/16 (f)
J3, N (f)
J4, N (f)
J1, 7/16 (m)
Brackets for Power Splitters, Power Tappers, Combiners and Couplers
Adjustable brackets, optimized for tun-nels and harsh environments
To simplify installation our brackets are multi-adjustable and made with ease of installation in mind.
Save money
Our brackets are optimized for Power Tap-pers, Power Splitters, Combiners and Cou-plers. When opting for quick and easy in-stallation, make sure to use our tailor made stainless steel or aluzinc brackets.
EGANTCELLULAR COMPONENTS
Egant Cellular ComponentsBox 945SE-114 79 StockholmSwedenPhone: +46 (0)8 62 00 650Fax: +46 (0)70 386 53 53E-mail: [email protected]
RevC
Technical Specifi cations - BracketsBelow are some typical data. For more detailed information, please contact us.
Product number: EG 300 0306 EG 300 0307 EG 699 0005
Mechanical Specifi cationsDimensions (W x H x D):Weight:Material:
30 x 77 x 80 mm0.2 kgStainless steel A4
30 x 77 x 80 mm0.2 kgAluzinc
80 x 60 x 30 mm0.15 kgAluzinc
Product number: EG 699 0006 EG 699 0007
Mechanical Specifi cationsDimensions (W x H x D):Weight: Material:
330 x 15 x 35 mm0.3 kgAluzinc
257 x 15 x 35 mm0.2 kgAluzinc
EG 699 0006Bracket for Egant combiners
EG 699 0007Bracket for Egant cellular couplers
EG 699 0005Bracket for Egant splitters/tappers (N)
EG 300 0306, EG 300 0307Bracket for Egant splitters/tappers (7/16)
Egant reserves the right to change this product specifi cation at any time without notice.