electric griddle installation & owners … griddle installation & owners manual serial...
TRANSCRIPT
AccuTemp Products, Inc. · 8415 North Clinton Park · Fort Wayne, IN 46825 ·800 210-5907 · accutemp.net
MP5004-1605
ELECTRIC GRIDDLE INSTALLATION & OWNERS MANUAL
Serial Number:Model:
Install Date:
Improper installation, alteration, adjustment,service, cleaning or maintenance of this commercial appliance could result in property damage, serious injury or death.
Read and understand the installation, operational, maintenance instructions before installing, servicing, or operating this commercial appliance.
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 1
Current Revision: Date Prior Revision DateN/A 8/4/05 None NoneInitial Release
Current Revision: Date Prior Revision DateA 8/16//05 N/A 8/4/5Added {ages 26,28-30 and 34-3; Renumbered pages as necessary
Current Revision: Date Prior Revision DateB 10/7/05 A 8/4/5Added paged ii and 24-27; Modified pages iv, 19-27; Renumbered page iv.
Current Revision: Date Prior Revision DateC 10/12/05 B 10/7/05Added page iii; Modified pages iv, 19-27; Renumbered page 4
Current Revision: Date Prior Revision DateD 11/10/05 C 10/12/05Deleted pages ii, iii and 25; Added pages 18,33 and 34; Modified pages 13,14, 25-32 and 35-40
Current Revision: Date Prior Revision DateE 12/29/05 D 10/12/05Added page ii; Modified pages 18, 19, 22-24, 33 and 34
Current Revision: Date Prior Revision DateMP5004-1202 2/14/12 E 12/29/05Numeric Page Numbers all pages; Pages modified for Engineering Changes
Current Revision: Date Prior Revision DateMP5004-1307 7/15/13 1202 2/14/12Added cut sheets pages 8-10; Changed graphic description - Page 14; Added Operation section - pages 22-24; Added Cleaning section- pages 25-26; Added Service & Troubleshooting section - pages 27-29; Added Parts Commercial section - pages 30-34; Added Military/Maritime Parts section - Pages 36-40; Added Schematic section
DOCUMENT HISTORY
Current Revision: Date Prior Revision DateMP5004-1605 5/24/2016 1307 7/15/13 Replaced Installation Checksheet with latest release pages 3-4 Replaced cut sheets pages 8-13; Operation section-page numbers change to 23-25; Cleaning section page numbers change to 26-27; Service & Troubleshooting secti page numbers change to 27-29; Model EGF Service Parts page numbers change to 31-38;Model EGD Service Parts section page numbers change to 39-48;Model EGF Schematics section page numbers change to 49-53; Model EGD Schematics sec-tion page numbers change to 54-57
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 2
DESCRIPTION PAGEDocument History 1Table of Contents 2Warranty Registration Instructions 3Startup Form 4-5Safety Warnings 6-8Accu-Steam Model EGF Specifications 9-12Accu-Steam Model EGD Specifications 13-14Accu-Steam Model EGD & EGF Theory of Operation 15Accu-Steam Model EGF Installation Instructions 16-18Accu-Steam Model EGD Installation Instructions 19-23Accu-Steam Model EGD & EGF Operation Instructions 24-26Accu-Steam Model EGD & EGF Cleaning Instructions 27-28Accu-Steam Model EGD & EGF Service & Troubleshooting 29-31Accu-Steam Model EGF Service Parts 32-39Accu-Steam Model EGD Service Parts 40-49Accu-Steam Model EGf Schematics 50-54Accu-Steam Model EGD Schematics 55-58Warranty 59
This manual is for Accu-Steam Griddles Starting with:Model EGD Series S/N 7547 Model EGF Series S/N 7642
This manual is to be used for all Accu-Steam Electric Models including:
Model NSNEGF4403B3602-00 7310-01-525-8008EGF4403B3602-T3 N/AEGF4403B2405-T3 7310-01-525-8934EGF4403B3605-T3 7310-01-525-8947EGF4403B4805-T3 7310-01-525-8948EGF4403B4802-00 7310-01-590-4486EGF4403A4805-T3 N/AEGD4403B3606-00 7310-01-525-8962EGD4403B4806-00 7310-01-525-8955
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 3
Before installing this appliance complete the following items:1. Fill in the warranty registration card enclosed in the documentation packet that came with the appliance.2. Complete the startup checklist on page 4 and 5 of this manual.3. Mail, fax or email the warranty registration card and startup form to AccuTemp Products, Inc
If you have any questions please contact our technical service group. They are available 7 days a week from 7:00 am to 7:00 pm EST.
Toll Free 800 480-0415Office 260 469-3040Fax 260 469-3045Email -Service [email protected] [email protected] Site www.accutemp.net
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 4
Contact Name:
Yes No
Yes No
Yes No
Yes No Yes No
Yes No
Yes No
15-50P
L16-20P
L16-30P
Store/Location:
Address:
Phone Number: Fax Number:
Check-Off List
Model # Serial #
Name of Service/Installer Company:
Is the correct NEMA Plug and Receptacle being used on the Supply Power Cord?
General :
Is the electrical wall receptacle positioned in a low heat-zone? Note: It is recommended that the wall receptacle be placed as low as State & Local codes allow. Placement in high heat-zones could cause damage to the electrical cord or plug that would not be covered under the product warranty.
Is the griddle level, both side-to-side and front-to-back?
If this is a table-top installation, have the (4) rubber foot tip/boots been installed?
Electrical Connection :
Is the Supply Power Cord being plugged into a wall outlet?
Is the Supply Power Cord being hard-wired, without the plug, to a breaker box?
Is the Supply Power Cord properly connected to GND?
208/240VAC (All Models)
440/480VAC (24" Models)
440/480VAC (36" & 48" Models)
Type of NEMA Plug?
MP5011-1403 Page: 1
Installation/Operational Checklist & Warranty Registration Form
ELECTRIC - ACCU-STEAM™
Failure to accurately complete and provide this Installation/Operational Checklist & Warranty Registration Form to AccuTemp Products, may delay or void future Warranty Service Calls.
** AccuTemp Products, Inc. is not responsible for the installation and/or modifications to the electrical supply source. **
What is the Electrical Breaker Amperage that will interupt the Supply Voltage to the electric griddle? AMPS
City: State: Zip:
Email:
Technician: Phone Number:
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 5
Yes No
Single Φ
208VAC 240VAC 440VAC 480VAC
Yes No
Yes No
Yes No
°F
No
Supply Power Electrical Readings :
Does the Supply Electrcial Power match the information on the griddle model number?
Temperature & Operational Verification :
Three Φ
1Φ = WHT BLK 3Φ = RED WHT BLK
Using a 9 square-grid-pattern on the griddle surface, are the surface temperatures consistant (±5°F)?
Using a weighted contact temperature probe with digital thermometer, does the surface temperature (°F) match the normal operating temperature (°F) set on the Thermostat? Note: DO NOT use an infrared or flat-top mercury thermometer . Yes
Does the unit operate properly for 15 minutes after the griddle has reached operating temperature?
I accept and submit this Installation/Operational Checklist & Warranty Registration Form as complete and accurate:
Restaurant/Facility Manager Approval:Signature Printed Name Date:
Page: 2
Phase (Φ)?
Measured Supply Voltage?
Measured Amperage on Each Leg?
AccuTemp Products, Inc Attn: Warranty Administration
8415 North Clinton Park Dr. Fort Wayne, IN 46825
Attn: Warranty Administration 260 469-3045
Attn: Warranty Administration [email protected]
Mail Fax Email
Does the Griddle heat light cycle OFF/ON once the surface temperature has reached the Thermostat setting?
What is the customer's normal operating Thermostat temperature for the Griddle?
MP5011-1403
Note: If the operating temperature is 250°F, then set Thermostat to 300°F and verify surface temperature. If the operating temperature is 400°F, then set Thermostat to 400°F and verify surface temperature does not exceed 396°F on the high side of the temperature drift/cycle.
Installation/Operational Checklist & Warranty Registration Form
ELECTRIC - ACCU-STEAM™
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 6
SAFETY WARNINGSSYMBOL DEFINITIONSSymbols are used to attract your attention to possible dangers. They are only effective if the operator uses proper accident prevention measures. Some of the symbols are boxed text, while other maybe just picture icons. Please give this information the respect they deserve for safe operation.
WARNING TEXT BOXESBelow are definitions of the warning text boxes:
WARNINGIndicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
CAUTIONIndicates a potentially hazardous situation which, if not avoided, could result in minor or moderate injury.
NOTEAdvises reader of information or instructions vital to the operation or maintenance of the equipment.
DANGERIndicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 7
CAUTION, HOT SURFACE
SAFETY WARNINGS CONTINUED
SYMBOL ICONSBelow are the definitions of symbol icons used in this manual;
ALERT - Notifies the reader of a n important message/warning, usually a safety related message.
DANGEROUS VOLTAGE
INFORMATION - Notifies the reader of important information that may or may not be safety related.
EARTH GROUND
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 8
Plug commercial appliance into a properly grounded electrical outlet of the correct voltage, size and plug configuration. If they do not match, contact a qualified electrician to determine the proper voltage and size and install the proper electrical outlet.
To avoid any personal injury or damage to the unit do not pull the commercial appliance by the power cord.
To prevent any injury, discontinue any use if power cord is frayed or worn.
To prevent any injury or damage this commercial appliance must be installed by a qualified electrician.
To avoid any injury, turn the power off, unplug from the power source and allow to cool before performing any maintenance.
To avoid electrical shock or personal injury, do not steam clean or use excessive water on this commercial appliance.
This product has no “user” serviceable parts. To avoid injury or damage to the commercial appliance use only Authorized AccuTemp Service Agents and Genuine Replacement Parts when service is required.
Genuine AccuTemp Replacement Parts are specified to operate safely in the environments in which they are used. Some aftermarket parts or generic replacements parts do not have the same specifications to operate safely in AccuTemp equipment. It is imperative that to use Genuine AccuTemp Replacement Parts to avoid injury or damage to the commercial appliance.
Always disconnect from power source before cleaning or servicing.
Any infield modification that bypass the built-in safety features will result in personal injury or death.
This commercial appliance must be properly grounded, in accordance with all National, State or local electrical codes.
This commercial appliance has a totally unique design and is constructed unlike any other griddle on the market today. Any modification may permanently damage the griddle.
This commercial appliance must be level for proper operation and to reduce possible damage to this commercial appliance.
This commercial appliance is heavy, for safe handling, the installer should obtain help as needed or employ appropriate material handling equipment to remove the commercial appliance from the skid and move to the final location in the building.
Temperatures in and around the commercial appliance are very hot and can cause severe burns.
To avoid damage to the cooking surface of this commercial appliance do not use abrasive cleaners such as a griddle stone or brick.
To avoid personal injury or damage to the commercial appliance do not use a water jet to clean this commercial appliance.
To avoid damage to the commercial appliance do not leave a chlorine sanitizer in contact with the stainless steel longer than 10 minutes.
To avoid severe burns slowly remove the grease reservoir to avoid spilling the contents. It is recommended to let it cool before removing.
IMPORTANT SAFETY INSTRUCTIONSIMPORTANT: Read the following safety installation to avoid personal injury or death and to avoid damage to the equipment or property
WARNINGS
CAUTIONS
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 9
Short Specification
Griddle shall be an Energy Star compliant electric-heated unit, with a hermetically-sealed vacuum chamber that produces steam that heats the 8-gauge stainless steel griddle plate. Efficient steam heat transfer provides 200–400°F (93–204°C) operating temperature range and uniform griddle surface temperatures of ±5°F (±3°C). Griddle fabricated from cold-rolled stainless steel with 4.5” high back splash, sides that taper from 4.5” to 1.7”, a 4” wide by 1” deep full front grease trough and 11⁄2–2 gallon grease drawer. Unit to be UL listed, UL EPH Sanitation Certified (NSF 4) and manufactured in the USA.
Construction Features
• Cold-rolled and annealed stainless steel griddle plate with polished stainless steel body and stand
• 8 gauge griddle plate with 4.5” high rear splash and 4.5 to 1.7” tapered side walls
• 4” wide by 1” deep full front grease trough
• 2” x 4” drop chute to 11⁄2–2 gallon capacity grease drawer inside enclosed compartment
• 4” legs with bullet feet (standard)
Performance Features
• Hermetically-sealed steam chamber heats griddle plate
• 9.6-kW [24”] or 14.25-kW total power, long-life low watt density heating elements mounted inside vacuum chamber and immersed in chemically pure water (Water never needs replacement)
• Steam transfers heat evenly to entire cooking surface with only ±5°F (±3°C) in temperature variation
• Rapid surface temperature recovery [10 seconds or less] allows turning product to same spot
• Smooth cold-rolled stainless steel griddle surface speeds and simplifies cleaning
Standard Control Features
• Power-On switch & indicator light• Heating indicator light• 200–400°F (93–204°C) solid state
thermostat• Easy front service access to controls
Cooking Capacity & Applications
Effective Cooking Area
Griddle Applications include:
• Pancakes, Eggs, Sausage, French Toast• Burgers, Grilled Onions, Toasted Buns• Grilled Cheese, Sandwiches• Fried Potatoes, Fish, Chicken Breasts,
Philly Steaks, Liver and MORE
Environmental Approvals & Programs
Other Approvals
Options & Accessories
• “U” Channel for connecting 2 griddles• Front mounted condiment board/prep
shelf—8” wide stainless steel• Heavy duty stainless steel stand with
bottom shelf with 5” casters• Condiment Board• Control Guards• Maritime Package (call for details)• Correction Package (call for details)• Chain Package (call for details)
Accu-SteAm™ Griddle eG SerieS
Electric/Steam-Heated, Tabletop Griddle
MM5206-1405
Project: ___________________________________ Location: ___________________________________ Item #: ___________________________________ Quantity:___________
AccuTemp Products, Inc. 8415 North Clinton Park • Fort Wayne, IN 46825 • 800-210-5907 • 260-493-0415 • Fax 260-493-0318 • accutemp.net
EGF-A36 Accu-Steam™Tabletop Griddle
Depth 24” Wide 36” Wide 48” Wide
29” 677 sq. in 1017 sq. in. 1358 sq. in.
24” 558 sq. in. 838 sq. in. 1119 sq. in.
NSF/ANSI 4
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 10
MM5206-1405
AccuTemp Products, Inc. 8415 North Clinton Park • Fort Wayne, IN 46825 • 800-210-5907 • 260-493-0415 • Fax 260-493-0318 • accutemp.net
Accu-Steam Griddle Specifications (replace **** with voltage & phase, i.e. 2083)
Model # EGF****A2400-T1 EGF****B2400-T1 EGF****A3600-T1 EGF****B3600-T1 EGF****A4800-T1 EGF****B4800-T1
KW Input 9.6 kW 9.6 kW 14.25 kW 14.25 kW 14.25 kW 14.25 kW
208/3 Amp Load 26.68 26.68 39.56 39.56 39.56 39.56
240/1 Amp Load 40 40 n/a n/a n/a n/a
240/3 Amp Load 39.58 39.58 34.28 34.28 34.28 34.28
440/3 Amp Load 17.1 17.1 25 25 25 25
480/3 Amp Load 15.41 15.41 22.87 22.87 22.87 22.87
Unit Width (A) 24.25 [616] 24.25 [616] 36.25 [921] 36.25 [921] 48.25 [1226] 48.25 [1226]
Unit Depth (D) 33.125 [841] 28.125 [714] 33.125 [841] 28.125 [714] 33.125 [841] 28.125 [714]
Cooking Surface Width (B) 23.875 [606] 23.875 [606] 35.875 [911] 35.875 [911] 47.875 [1216] 47.875 [1216]
Cooking Surface Depth (C) 28.375 [721] 23.375 [594] 28.375 [721] 23.375 [594] 28.375 [721] 23.375 [594]
Depth to Front Leg (E) 3.188 [81] 5.688 [144] 3.188 [81] 5.688 [144] 3.188 [81] 5.688 [144]
Effective Cooking Area 677 sq. in. 558 sq. in. 1017 sq. in. 838 sq. in. 1358 sq. in. 1119 sq. in.
Grease Pan Capacity 1.5 gal. 1.5 gal. 2 gal. 2 gal. 2 gal. 2 gal.
NEMA Plug (208/240) 15-50P 15-50P 15-50P 15-50P 15-50P 15-50P
NEMA Plug (440/480) L16-20P L16-20P L16-30P L16-30P L16-30P L16-30P
Accu-SteAm™ Griddle eG SerieS
Electric/Steam-Heated, Tabletop Griddle
Notes:1.) Dimensions in brackets [ ] are metric.2.) 5’ power cord wtih plug provided.
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 11
Short Specification
Griddle shall be an Energy Star compliant electric-heated unit, with a hermetically-sealed vacuum chamber that produces steam that heats the 8-gauge stainless steel griddle plate. Efficient steam heat transfer provides 200–400°F (93–204°C) operating temperature range and uniform griddle surface temperatures of ±5°F (±3°C). Griddle fabricated from cold-rolled stainless steel with 4.5” high back splash, sides that taper from 4.5” to 1.7”, a 4” wide by 1” deep full front grease trough and 11⁄2–2 gallon grease drawer. Griddle to be mounted on heavy duty stainless steel stand with one undershelf and casters. Unit to be UL listed, UL EPH Sanitation Certified (NSF 4) and manufactured in the USA.
Construction Features
• Cold-rolled and annealed stainless steel griddle plate with polished stainless steel body and stand
• 8 gauge griddle plate with 4.5” high rear splash and 4.5” to 1.7” tapered side walls
• 4” wide by 1” deep full front grease trough
• 2” x 4” drop chute to 11⁄2–2 gallon capacity grease drawer inside enclosed compartment
• 5” heavy-duty casters standard, front are locking type (optional bullet or flanged feet)
Performance Features
• Hermetically-sealed steam chamber heats griddle plate
• 9.6-kW [24”] or 14.25-kW total power, long-life low watt density heating elements mounted inside vacuum chamber and immersed in chemically pure water (Water never needs replacement)
• Steam transfers heat evenly to entire cooking surface with only ±5°F (±3°C) in temperature variation
• Rapid surface temperature recovery [10 seconds or less] allows turning product to same spot
• Smooth cold-rolled stainless steel griddle surface speeds and simplifies cleaning
Standard Control Features
• Power-On switch & indicator light• Heating indicator light• 200–400°F (93–204°C) solid state
thermostat• Easy front service access to controls
Cooking Capacity & Applications
Effective Cooking Area
Griddle Applications include:
• Pancakes, Eggs, Sausage, French Toast• Burgers, Grilled Onions, Toasted Buns• Grilled Cheese, Sandwiches• Fried Potatoes, Fish, Chicken Breasts,
Philly Steaks, Liver and MORE
Environmental Approvals & Programs
Other Approvals
Options & Accessories
• “U” Channel for connecting 2 griddles• Front mounted condiment board/prep
shelf—8” wide stainless steel• Condiment Board• Control Guards• Maritime Package (call for details)• Correction Package (call for details)• Chain Package (call for details)
Accu-SteAm™ Griddle eG SerieS
Electric/Steam-Heated, Stand-Mounted Griddle
MM5205-1405
Project: ___________________________________ Location: ___________________________________ Item #: ___________________________________ Quantity:___________
AccuTemp Products, Inc. 8415 North Clinton Park • Fort Wayne, IN 46825 • 800-210-5907 • 260-493-0415 • Fax 260-493-0318 • accutemp.net
EGF-A36 Accu-Steam™Stand-Mounted Griddle
(also available with bullet or flanged feet)
Depth 24” Wide 36” Wide 48” Wide
29” 677 sq. in 1017 sq. in. 1358 sq. in.
24” 558 sq. in. 838 sq. in. 1119 sq. in.
NSF/ANSI 4
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 12
AccuTemp Products, Inc. 8415 North Clinton Park • Fort Wayne, IN 46825 • 800-210-5907 • 260-493-0415 • Fax 260-493-0318 • accutemp.net
Accu-Steam Griddle Specifications (replace **** with voltage & phase, i.e. 2083)
Model # EGF****A2400-S2 EGF****B2400-S2 EGF****A3600-S2 EGF****B3600-S2 EGF****A4800-S2 EGF****B4800-S2
KW Input 9.6 kW 9.6 kW 14.25 kW 14.25 kW 14.25 kW 14.25 kW
208/3 Amp Load 26.68 26.68 39.56 39.56 39.56 39.56
240/1 Amp Load 40 40 n/a n/a n/a n/a
240/3 Amp Load 39.58 39.58 34.28 34.28 34.28 34.28
440/3 Amp Load 17.5 17.5 25 25 25 25
480/3 Amp Load 15.41 15.41 22.87 22.87 22.87 22.87
Unit Width (A) 24.25 [616] 24.25 [616] 36.25 [921] 36.25 [921] 48.25 [1226] 48.25 [1226]
Unit Depth (D) 33.125 [841] 28.125 [714] 33.125 [841] 28.125 [714] 33.125 [841] 28.125 [714]
Cooking Surface Width (B) 23.875 [606] 23.875 [606] 35.875 [911] 35.875 [911] 47.875 [1216] 47.875 [1216]
Cooking Surface Depth (C) 28.375 [721] 23.375 [594] 28.375 [721] 23.375 [594] 28.375 [721] 23.375 [594]
Depth to Front Leg (E) 3.188 [81] 5.688 [144] 3.188 [81] 5.688 [144] 3.188 [81] 5.688 [144]
Effective Cooking Area 677 sq. in. 558 sq. in. 1017 sq. in. 838 sq. in. 1358 sq. in. 1119 sq. in.
Grease Pan Capacity 1.5 gal. 1.5 gal. 2 gal. 2 gal. 2 gal. 2 gal.
NEMA Plug (208/240) 15-50P 15-50P 15-50P 15-50P 15-50P 15-50P
NEMA Plug (440/480) L16-20P L16-20P L16-30P L16-30P L16-30P L16-30P
Accu-SteAm™ Griddle eG SerieS
Electric/Steam-Heated, Stand-Mounted Griddle
Notes:1.) Dimensions in brackets [ ] are metric.2.) 5’ power cord with plug provided.
MM5205-1405
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 13
Short Specification
Griddle shall be an AccuTemp Model EG modular drop-in electric heated unit, with hermetically-sealed vacuum chamber that produces steam to heat the 8-gauge stainless steel griddle plate. Efficient steam heat transfer provides 200–400°F (93–204°C) operating temperature range and uniform griddle surface temperatures of ±3°F (±1°C). Unit is fabricated in two modules with water and grease resistant front control panel and insulated and sealed griddle cook surface drop-in, fabricated from cold-rolled stainless steel recessed 1.5” below work surface, with 3” wide by 1.25” deep full front grease trough and 1.5-gallon grease drawer. Unit to be UL listed, UL EPH Sanitation Certified (NSF 4) and manufactured in the USA.
Construction Features
• Cold-rolled and annealed stainless steel griddle plate with polished stainless steel body and stand
• 8 gauge griddle plate with 4.5” high rear splash and 4.5 to 1.7” tapered side walls
• 3” wide by 1.25” deep full front grease trough
• 2” x 4” drop chute to 11⁄2 gallon capacity grease drawer inside enclosed compartment
• Sealed control panel provided for cabinet front mounting
Performance Features
• Hermetically-sealed steam chamber heats griddle plate
• 9.6-kW [24”] or 14.25-kW total power, long-life low watt density heating elements mounted inside vacuum chamber and immersed in chemically pure water (Water never needs replacement)
• Steam transfers heat evenly to entire pan surface with only ±5°F (±3°C) in temperature variation
• Rapid surface temperature recovery [10 seconds or less] allows turning product to same spot
• Smooth cold-rolled stainless steel griddle surface speeds and simplifies cleaning
Standard Control Features
• Power-On switch & indicator light• Heating indicator light• 200–400°F (93–204°C) solid state
thermostat• Easy front service access to controls
Cooking Capacity & Applications
Effective Cooking Area
Griddle Applications include:
• Pancakes, Eggs, Sausage, French Toast• Burgers, Grilled Onions, Toasted Buns• Grilled Cheese, Sandwiches• Fried Potatoes, Fish, Chicken Breasts,
Philly Steaks, Liver and MORE
Environmental Approvals & Programs
Other Approvals
Options & Accessories
• Control Guards• Maritime Package (call for details)• Chain Package (call for details)• Control panel available in left mount,
right mount and center mount
Accu-SteAm™ Griddle eG SerieS
Electric/Steam-Heated, Drop-In Griddle
MM5207-1405
Project: ___________________________________ Location: ___________________________________ Item #: ___________________________________ Quantity:___________
AccuTemp Products, Inc. 8415 North Clinton Park • Fort Wayne, IN 46825 • 800-210-5907 • 260-493-0415 • Fax 260-493-0318 • accutemp.net
EGD-B36 Accu-Steam™Drop-In Griddle
Depth 36” Wide 48” Wide
24” 799 sq. in. 1093 sq. in.
NSF/ANSI 4
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 14
MM5207-1405
AccuTemp Products, Inc. 8415 North Clinton Park • Fort Wayne, IN 46825 • 800-210-5907 • 260-493-0415 • Fax 260-493-0318 • accutemp.net
Accu-Steam Drop-In Griddle Specifications (replace **** with voltage & phase, i.e. 2083)
Model # EGD****B3600-00 EGD****B4800-00
KW Input 14.25 kW 14.25 kW
208/3 Amp Load 39.56 39.56
240/3 Amp Load 34.28 34.28
440/3 Amp Load 21 21
480/3 Amp Load 17.14 17.14
Unit Width (A) 36.5 [927] 49 [1245]
Unit Depth (D) 29.5 [749] 29.5 [749]
Cooking Surface Width (B) 34 [864] 46.5 [1181]
Cooking Surface Depth (C) 23.5 [597] 23.5 [597]
Effective Cooking Area 799 sq in[20295 sq mm]
1093 sq in[27762 sq mm]
Rough Opening Griddle 35.5 x 28.5[902 x 724]
47.75 x 28.5[1213 x 724]
Rough Opening Control Panel
33.75 x 4.875[857 x 124]
33.75 x 4.875[857 x 124]
Grease Pan Capacity 1.5 gal. 1.5 gal.
NEMA Plug (208/240) 15-50P 15-50P
NEMA Plug (440/480) L16-30P L16-30P
Accu-SteAm™ Griddle eG SerieS
Electric/Steam-Heated, Drop-In Griddle
Notes:1.) Dimensions in brackets [ ] are metric.2.) 5’ power cord wtih plug provided.
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 15
THEORY OF OPERATION
INTRODUCTIONThe ACCU-STEAM™ griddle is constructed and uses technology like no other griddle in the world. The diagram below is a cross-sectional view of the griddle. The griddle cooking surface is the top of a chamber in which we have produced a unique environment. Welded stainless steel reinforcement studs connect the chamber top to the chamber bottom. The perimeter joints are all robotically welded to produce a vessel that is airtight, which is verified using a helium mass spectrometer. The chamber is filled half full with distilled water. The remaining air is removed and the chamber is welded shut. At this point, the chamber becomes a hermetically sealed vessel, never to be opened again. The griddle steam chamber requires no water or maintenance. A thermowell for a temperature sensor to sense temperature and a thermowell for the over temp safety shutdown system are also welded into the griddle steam chamber.
At temperatures below 212°F (100°C), the chamber is actually in a vacuum, similar to that of a canning jar. At temperatures above 212°F (100°C), the chamber operates under pressure. Located between the water and the bottom of the cooking surface is the best heat transfer medium – steam, the most effective way to transfer heat. The temperature sensor senses the temperature of the steam and reports this data to the thermostat, which energizes the heating elements. This system maintains the griddle cooking surface temperatures to within ± 5°F (2.7°C) over the entire cooking surface and provides a near instant temperature recovery, even in the same spot on the griddle, when turning food in place.
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 16
ELECTRIC TABLE TOP & STANDMODEL EGF SERIES
INSTALLATION INSTRUCTIONS
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 17
INSTALLATION TABLE TOP/STAND MODEL - EGF SERIES
LOCATION AND PLACEMENTThe ACCU-STEAM electric griddle has been designed to be placed on a commercial kitchen counter-top, an AccuTemp griddle stand or directly onto any flat, level surface that will support the appliance weight.The operating temperature ranges from 200°- 400°F (93°- 204°C). Since these temperatures can also be found on surfaces around the perimeter of the griddle, care should be given not to install griddle next to or against, objects or surfaces with a low melting or flash point.
TOOLS REQUIRED:
Spirit Level Clamp Amp MeterPhillips Screw Driver Weighted Temperature ProbeSmall Blade Straight Screw Driver Digital Temperature MeterDigital Volt Meter
IN-FIELD MODIFICATIONSThis appliance has a totally unique design and is constructed unlike any other griddle on the market today. Any modification may permanently damage the griddle.
Only a qualified service or electrician should complete the installation to ensure that all electrical and safety requirements are met and that all wiring is installed as per all National, State and Local electrical codes.
WARNING
This appliance is heavy. For safe handling, the installer should obtain help as needed or employ appropriate material handling equipment to remove the appliance from the skid and move into the final destination.
WARNING
Any in field modifications made without written authorization from AccuTemp™ will void all warranties
NOTE
LEVELING The appliance must be installed in a level condition. An out-of-level condition may cause uneven temperatures and in a severe out of level condition damage to the appliance can occur. Use a spirit level resting on the appliance cooking surface to ensure it is level front-to-back and left-to-right.
The griddle must be level front to back and side to side. Warranty will be void if not.
WARNING
Any in field modifications that bypasses the safety features could result in injury or death.
WARNING
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 18
INSTALLATION TABLE TOP/STAND MODEL - EGF SERIES
ELECTRICAL SUPPLYThe ACCU-STEAM™ griddle has been designed, manufactured and tested to meet or exceed the demanding standards of safety set forth by Underwriters Laboratories, Inc. To to ensure that this high level of safety is maintained in your installation, it is important that you read and understand the following information before attempting to plug in your griddle.
ELECTRICAL REQUIREMENTSElectrical requirements are listed on the data plate located on the right side of the unit, near the front. All standard AccuTemp griddles are supplied with a 6ft (1.83m) cord and the appropriate UL listed plug. Make sure that the voltage at your supply receptacle is within ± 10 % of the voltage listed on the griddle data plate. Connection to any other voltage may cause damage to components in the appliance. The appliance plug must be used with the appropriate receptacle. Direct wiring will void the warranty.
This appliance must be properly grounded, In accordance with all the National, State and local electrical codes.
WARNING
GROUNDING INSTRUCTIONSGrounding provides a path for electric current to reduce the risk of shock. This product is equipped with a power cord having a grounding conductor and a grounding plug.
ELECTRICAL CONNECTIONS (EGF MODELS ONLY)The receptacle requirements vary between models. For a 240 V single-phase model, you will need a NEMA 6-50R receptacle. If you have purchased 208/240V three-phase model, you will need a NEMA 15-50R receptacle and if you purchased a 440V/480V three-phase model you will need a NEMA L16-30R receptacle.
NEMA 6-50R NEMA 15-50R NEMA L16-30R
240V Single 208/240V 3 Phase 440/480V 3 Phase
LEVELING - CONTINUEDTABLE TOPInstall the (4) rubber foot tips provided with your appliance onto the four foot adjusters of each of the appliance legs. This will keep the griddle from sliding on the counter-top under normal use. Once the rubber foot tips have been installed, adjust the four foot adjusters up or down as needed to level the griddle.ACCUTEMP STAND If on an AccuTemp griddle stand with casters, ensure that the floor surface is level and place the two locking casters to the “on” position and follow the leveling instructions to verify the appliance is level.
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 19
Fig. 1IntroductionIt is highly recommended that a survey of the kitchen site be conducted to determine the requirements for the installation. Electrical supply, counter space as well as counter arrangement are critical to the choice of Drop-In-Griddle options. The Drop-In-Griddle is available in many options to accommodate size, control panel arrangements and supply voltage. The model data label indicating the model number, phase, voltage, current, wattage and UL™ information is located on the bottom cover of the unit.
Counter designs that have an “L” arrangement such that the shortest part of the “L” is to the left may require a “Right Hand Control Panel” option. A counter design that has an “L” arrangement such that the shortest part of the “L” is to the right may require a “Left Hand Control Panel” option. See Figure 1 for views of these configurations.
INSTALLATION MODEL EGD DROP-IN GRIDDLE
This product is to be installed in stainless or non-combustible counter tops only.
CAUTION
Installation must allow for inspection and serviceability to the underside of the appliance.
NOTE
ELECTRICAL SUPPLYThe ACCU-STEAM™ griddle has been designed, manufactured and tested to meet or exceed the demanding standards of safety set forth by Underwriters Laboratories, Inc. To ensure that this high level of safety is maintained in your installation, it is important that you read and understand the following information before attempting install your griddle.
ELECTRICAL REQUIREMENTSElectrical requirements are listed on the data plate located on the Bottom of the Control Box, near the front. The EGD Series griddles are supplied with a 5 foot (1.52m) cord. Make sure that the voltage at your supply is within ± 10 % of the voltage listed on the griddle data plate. Connection to any other voltage may cause damage to components in the griddle and damage of this type is not covered under warranty.
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 20
INSTALLATION MODEL EGD DROP-IN GRIDDLE (cont.)
This appliance must be properly grounded, in accordance with all National, State and local electrical codes.
WARNING
GROUNDING INSTRUCTIONSGrounding provides a path for electric current to reduce the risk of shock. This product is equipped with a 5 foot power cord with a grounding conductor.
GETTING STARTEDPlease read and comprehend all instructions and manuals provided with each Drop-In-Griddle. Read and understand all safety warnings and operator instructions for all powered tools required to complete the installation of the Drop-In-Griddle. Disconnect all power from house supply connection boxes at the appropriate fuse panel and label the breakers “In service”.
This is to warn others that work is in process, preventing accidental electrocution.
TYPICAL TOOLS AND SUPPLIES REQUIREMENTS• Putty knife• Grease solvents• Clean sponges or rags• Latex gloves• Caulking gun• Approximately 3oz. NSF-approved aluminized silicone sealant• Tape measure• Carpenters square• #2 Phillips screw driver• Channel lock pliers• ½ inch box/open wrench• 3/8 inch nut driver• 3/8 inch electric or cordless drill• #25 drill bit• 3/8 inch drill bit• Saber saw with metal cutting blades• Permanent marking pen, preferably a “Sharpie” fine point. • 4 inch grinder. (If replacing an existing competitors griddle, it is recommend to use a 4 inch grinder to
clean off any welds, welded on brackets or framing attached to the counter top.)
1. Inspect the griddle packaging to ensure there are no missing components.Parts Contained in the Packaging:
QTY DESCRIPTION PART NUMBER
1 Griddle Module AT2A-2520
1 Control Panel Assembly AT2A-2772
1 Cable Assembly - 24 inch AT2A-2764-1
1 Grease Spout Extension - 1” AT2A-2592-1
1 Grease Spout Extension - 2” AT2A-2592-2
1 Grease Spout Extension - 3 “ AT2A-2592-3
1 Grease Spout Extension - 4 “ AT2A-2592-4
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 21
INSTALLATION MODEL EGD DROP-IN GRIDDLE (cont.)
Fig. 2
QTY DESCRIPTION PART NUMBER
8 Screw, #10 Type AB x 1/2 Truss Head AT0F-2777-41040
6 Screw, 10-24 UNC x 1/2 inch Phillips Round Head Machine AT0F-2755-41040
2 Bolt, 5/16 -18 UNC 2A 3/4” Carriage AT0F-1921-61060
2 Washer, 5/16 “ Helical Spring Lock AT0F-1922-60000
2 Nut, 5/16-18 x UNC 2B SS Hex Machine AT0F-2778-61000
8 1/4-20 Nyloc Nut AT0F-2691-51002
4 Retainer Brackets AT2M-2535-1
1 Grease Trough Hngr Brkt AT2M-2553-1
1 Grease Trough Hanger AT2M-2554-1
6 Washer, #10 Internal Tooth Lock AT0F-2666-40000
1 Grease Trough Assembly AT2A-2529
1 Grease Tray Assembly AT2A-2552
1 Electric Griddle Owners Manual MP5004
1 Registration Card AT0T-3033-1
2. Complete the appropriate power disconnection procedures for existing equipment or local power junction boxes.
3. Clean surfaces with grease solvents and dry off with clean rags or sponges.
4. Determine the location and orientation for the griddle and control panel modules. Mark the center line on the counter top for the griddle module, using a Carpenter’s square. See Figure 2 for the counter top and control panel layouts. Continue the center line to the control panel module mounting surface. Accurate center line alignment of the counter top and control panel modules is critical to ensure the correct alignment of the grease trough assembly to the griddle module.
Parts Contained in the Packaging:
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 22
INSTALLATION MODEL EGD DROP-IN GRIDDLE (cont.)5. The dimensional relationship between the griddle module mounting flange and the control
panel module is shown in Figure 3. The griddle module mounting flange overlaps the counter top cutout by 0.50 inches on all four sides. Mark the griddle module cutout on the counter top such that the front edge of the griddle module is 0.73 inches – 2.63 inches from the control panel module mounting surface, as shown in Figure 3. Mark the control panel module cutout on the control panel module mounting surface, as shown in Figure 2.
Fig. 3
6. Cut out the griddle and control panel module openings. Straighten out any dings or bent edges in both cutouts to ensure adequate sealing between the new griddle and the counter top surface and between the control panel and the front surface of the counter.
7. Drillthemountingholesinthefaceofthecounterusinga#25drillbit.Drillthefirstsetofholesandlocate the remaining holes using the control panel as a template.
8. Use a lifting device, if possible, to raise the griddle module above the counter and position over cutout in counter top. Lower the griddle module carefully into the cutout. Install the retainer clamps to the griddle module, using the ¼-20 nyloc nuts (see drawing AT2A-3044, sheet 6).
9. Install the control panel onto the counter face using #10-24 x 3/8 inch self-tapping screws. Also, at this time, install the thermostat knob guard, if necessary, by lining up the holes on the guard to the holes on the control panel directly above and below the thermostat.
10. Install the grease trough hanger brackets onto the bottom side of the griddle using (2) #10-24 X ½ inch Phillips round head machine screws and (2) 5/16-18 X ¾ inch carriage head bolts with (2) 5/16 inch lock washers and (2) 5/16-18 nuts (see drawing AT2A-3044, sheet 6). Leave the carriage bolts loose for adjustment of the grease trough.
11. Install the grease trough using (4) #10-24 X ½ inch Phillips round head machine screws through the front panel opening and through the hanger bracket assembly, installed in step 10.
12. Adjust the hanger bracket height so that the grease trough is setting level front-to-back and tighten the 5/16-18 nuts.
13. Install the appropriate size grease spout extension onto the griddle grease spout, that ensures the bottom
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 23
INSTALLATION MODEL EGD DROP-IN GRIDDLE (cont.)
ofthegreasespoutextensionisflushtotheinsidesurfaceofthegreasetroughassembly(seedrawingAT2A-3044, sheet 6).
14. Use the caulking gun to lay a 1/8” minimum diameter bead of the aluminized silicone sealant around the griddlemodulemountingflangeontothecountertop.Useaglovedfingertowipethesealantintoafilletshape.
15. Install the interconnect cable between the control panel module and the control box, mounted on the bottom side of the griddle (see drawing AT2A-3044, sheet 6).
16. Set the on/off switch to the off position and set the temperature control knob to the lowest setting.17. Install the power cord into an appropriate sized electrical connection box with an appropriate sized cord
griporcablestrainrelief.Completethefinalconnections,testingthehousesupplywirefirsttoensureitis not live.
18. Turn on power to the griddle at the fuse panel.19. Turn the griddle on and set the temperature control knob to a 350°F. Allow the griddle heat light to
cycle a minimum of two times before checking the temperature. Then use a weighted temperature probe and a digital temperature-measuring device to check the griddle surface temperature. The surface temperature should be within 5 – 7 °F of the temperature control knob setting. If it is not, go to the calibration section and follow the calibration procedures.
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 24
OPERATIONMODEL EGD & EGF
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 25
SEASONINGIt is recommended that you clean your ACCU-STEAM™ griddle thoroughly before using it for the first time. To clean the griddle surface, just simply wash the cooking surface down with a solution of mild soap and water, and then rinse thoroughly with clean water.
Once the cooking surface has been cleaned, set the thermostat to 200°F (93°C), turn the griddle power switch to the “On” position and allow the griddle cooking surface to heat for 10 minutes. Using a high temperature oil, such as Pan and Grill Shortening™, Whirl™ or equivalent, pour enough to cover the entire griddle surface. Do not use standard vegetable oil to season the griddle cooking surface. It may cause food to stick and result in improperly cooked food. Work this seasoning oil into the griddle surface with a regular heavy-duty scrub pad for about 5 minutes, making sure that you scrub the seasoning oil over the entire griddle-cooking surface. After the entire griddle surface has been scrubbed with seasoning oil for 5 minutes, simply wipe or squeegee off excess oil from griddle surface. Your griddle is now ready to use!If you use chemicals to clean your griddle periodically or on a schedule, you may need to repeat this process after the use of chemicals.
PREHEATINGTurn On switch to the “On” position and set the thermostat to the desired temperature. The griddle will increase its surface temperature at an average rate of 15° F (8°C) per minute. It takes approximately 22 minutes to raise the griddle from room temperature to its maximum temperature of 400° F (204°C). The griddle will be preheated when the “Heat” light starts to cycle on and off. Please use caution as temperatures on and around the griddle cooking surface could cause severe burns.
COOKINGBegin cooking only after the griddle has been preheated to the desired temperature. Please note these facts:
• You can cook all the way to the edges of the griddle surface because the temperature does not very across the entire cooking surface.
• You can turn the product to the same spot because the griddle has near instant heat recovery.
• It will always cook the same, regardless of product load or surface coverage.Accurate Cooking TemperaturesBecause of the inaccurate surface temperatures and long recovery times common with other griddles. It is doubtful you were cooking at the set temperature or the temperature you wanted. Adjust the temperature on your ACCU-STEAM™ griddle and it will not change or vary by the location on the griddle surface. There are no hot or cold zones.
Heat LampIt is normal for the heat light to cycle on and off. This light indicates when the heaters are energized. You will soon notice how little they are energized to maintain perfect surface temperatures on your griddle.
OPERATION
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 26
OPERATION (cont.)
Weighted Temperature Probe Digital Temperature Reading Device
Due the construction material of the griddle cooking surface an infrared temperature probe can’t be used. The proper measurement tools to use are a weighted temperature probe and digital temperature as shown below. ( Fig. 5)
CHECKING SURFACE TEMPERATURE
Fig. 5
Accu-Steam™ Installation and Owners ManualMP5004-1605
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 27
CLEANINGMODEL EGD & EGF
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 28
DAILY CLEANINGCleaning the cooking surface during the work shift can be performed with a sharp scraper. When heavy cleaning at the end of a shift or periodically through the day is needed, the following is recommended:
• Empty the grease pan as often as needed and always prior to end of shift cleaning. • Turn the griddle off and allow it to cool to between 220°F and 240°F (104°C and 116°C). Scrap off
heavy deposits and remove any standing grease before proceeding with the cleaning process.• Use water, ice and/or griddle cleaner as needed. For example, the 3M Scotch-Brite™ Quick Clean
Griddle System provides the Scotch-Brite polishing pads, quick clean liquid, pad holder and squeegee. Clean-up is very easy using these tools with the quick clean liquid, water, ice or combinations of these liquids.
• Empty the grease pan after and wash with a mixture of dish detergent and clean water and dry with a clean dry cloth after the clean the non-cooking surfaces with a damp cloth and dry with a clean dry cloth after the surface is cool to the touch. Use a high quality stainless steel cleaner on a clean cloth to keep these surfaces
• Seasoning the griddle after the daily cleaning is recommended.
NOTEDo not use a appliance stone or brick to clean griddle cooking surface. Only use a fabric scrub pad.
NOTEDo not use a water-jet to clean the griddle as it can harm the electronic components in the appliance.
Grease PanUse caution when emptying the grease pan. The contents in this pan could cause severe burns. The pan should be checked periodically and emptied as necessary to prevent an overflow or dangerous condition.
The grease can contents could cause severe burns. Slowly remove the grease can from the griddle to avoid spilling the contents
WARNING
CAUTIONIf the cooking surface of the appliance has standing grease and the griddle is at a high temperature using water or ice can cause the grease to splatter and cause skin burns.
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 29
SERVICE & TROUBLESHOOTINGMODEL EGD & EGF
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 30
WARRANTY PROCEDURE
An AccuTemp Products, Inc. Technical Service Technician is available: Monday thru Sunday, 7:00am to 7:00pm EST.
SERVICE AND TROUBLESHOOTING (cont.)
1. Contact the AccuTemp Technical Service group for all warranty service requests.2. Be prepared to supply the serial number, address, location phone and contact for the location.3. Be prepared to complete a few simple tasks to help evaluate the problem.4. If the problem requires service at the location the AccuTemp Technical Service group will dispatch
the nearest authorized service agent.
NOTEService should be completed by AccuTemp authorized service groups. Service completed by unauthorized groups will void all factory warranties.
NOTEAccuTemp™ Technical Service group must be contacted for all warranty service requests or the warranty claim my be denied.
Toll Free 800 480-0415Office 260 469-3040Fax 260 469-3045Email -Service [email protected] [email protected] Site www.accutemp.net
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 31
BASIC TROUBLESHOOTING
Griddle will not turn on• Make sure the griddle is plugged in and the “On/Off” switch is in the On position.• Check for a facility circuit breaker (or fuse) supplying the unit
Heat light will not come on• Make sure the griddle is not hotter than the temperature you have it set for. If you have
turned down the temperature of the griddle, the heat light will not come on again until the cooking surface drops below the temperature you have set.
• See if the heat light is coming on intermittently. While operating in a normal condition, the heat light cycles on and off periodically when at temperature.
Uneven or inaccurate surface temperatures• Verify griddle is level front to back and side to side.• Verify the surface temperature with an accurate digital surface probe thermometer. • Use of an infrared thermometer will not give an accurate reading of the griddle surface
temperatures.• Contact AccuTemp Technical Service for additional instructions.
Unit will not turn off• This system, which is extremely rare, indicates a serious control malfunction. • Turn off the griddle’s electrical supply at the source and contact AccuTemp Technical Service
for additional Instructions.
SERVICE AND TROUBLESHOOTING
Use of any replacement parts other than those supplied by AccuTemp can cause injury to the operator or damage the appliance and voids all warranties
WARNING
There are no user-serviceable parts. To prevent electrical shock do not open the access panel covers.
WARNING
Any in-field modification that bypass the built in safety features of this appliance will result in death or serious injury.
WARNING
NOTEService should be completed by Accutemp™ authorized service groups. Service completed by unauthorized groups will void all factory warranties.
Accu-Steam™ Installation and Owners ManualMP5004-1605
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 32
SERVICE PARTSMODEL EGF
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 33
ITEM PART NUMBER DESCRIPTION
1 AT0E-1800-5 INDICATOR LAMP RED 250V
2 AT0E-1800-4 INDICATOR LAMP GREEN 250V
3 AT0E-3336-1 OPERATOR, AB ROTARY SWITCH
4 AT0F-1046-31030 SCREW,#8-32 X 3/8 PHLP TRUSS HEAD
5 AT0E-3336-1 OPERATOR, AB ROTARY SWITCH
6 AT0F-3371-1 NUT ROTARY SHAFT SEAL
7 AT0E-3189-1 ASSY, EG EXTERNAL THERMOSTAT
8 AT2G-1026-1 GASKET, CONTROL PANEL EG
9 AT0E-2559-7 THERMOSTAT, RTD
10 AT0E-3339-1 MOUNTING LATCH
11 AT0E-3338-1 CONTACT BLOCK
12 AT0A-2876-1 MDR WITH TERMINALS
13 AT0F-2777-31030 SCREW #8 TYPE AB X 3/8 TRUSS HD
14 AT2M-1559-1 COVER
15 AT2A-2916-1 HIGH LIMIT OVERTEMP ASSEMBLY (See Page 8)
16 AT0E-2885-3 SENSOR, REPLACEABLE, RTD
17 AT0F-2755-41070 SCREW, #10-24UNCX7/8 PHILIPS ROUND HEAD MACHINE
18 AT0E-1134-4 4 POSITION TERMINAL BLOCK
19 AT0E-3025-2 INSULATOR STRIP, DOUBLE ROW
20 AT0F-2691-41002 NUT, 10-24 NYLOC
1
3
2
4 5 6 7 8
9
10 11
13
15
1412
16
17 19
20
18
21
2422
23
2625
2827
29 30
3332
31
34
MODEL EGF COMMERCIAL MODELS
SEE PAGE 8
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 34
ITEM PART NUMBER DESCRIPTION
21 AT0F-2662-3 TRANSFORMER 440V,480V22 AT2A-3032-3 4” LEG ASSEMBLY, FLANGE, OPTIONAL
22.1 AT2A-3032-1 4” LEG ASSEMBLY, STANDARD (NOT SHOWN)22.2 AT2A-3032-2 8” LEG ASSEMBLY, OPTIONAL (NOT SHOWN)23 AT0F-2875-51062 SCREW, 1/4-20UNC x3/4 HEX HEAD MACHINE 24 AT0E-1587-1 3 POLE CONTACTOR25 AT0F-2755-41040 SCREW, #10-24UNC X1/2 PHILPS ROUND HEAD MACHINE26 AT0F-1046-31030 SCREW, #8-32 X 3/8 PHLP TRUSS HEAD27 AT2M-1021-1 PANEL, EGF ACCESS POWER TERMINAL28 AT2G-1022 GASKET, EGF ACCESS POWER TERMINAL29 AT0E-1049-5 CONNECTOR, 1” HUB STRAIN RELIEF30 AT0A-2788-14 POWER CABLE ASSEMBLY - 440V
30.1 AT0A-2788-17 POWER CABLE ASSEMBLY - 208V/3 PHASE (NOT SHOWN)30.2 AT0A-2788-18 POWER CABLE ASSEMBLY - 240V/SINGLE PHASE (NOT SHOWN)30.3 AT0A-2788-19 POWER CABLE ASSEMBLY - 480V/3 PHASE31 AT2M-3183-1 BAR, 24” GRIDDLE GRAB (OPTIONAL)
31.1 AT2M-3183-2 BAR, 36” GRIDDLE GRAB (OPTIONAL) ( NOT SHOWN) 31.2 AT2M-3183-3 BAR, 48” GRIDDLE GRAB (OPTIONAL) (NOT SHOWN) 32 AT2H-3184-1 END BRKTS, GRIDDLE GRAB BAR (OPTIONAL) 33 AT0F-2778-71001 NUT, 3/8-16UNC-2B 11 HEXMACHINE SCREW
MODEL EGF COMMERCIAL MODELS
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 35
MODEL EGF MARITIME MODELS
ITEM NUMBER PART NUMBER DESCRIPTION
1.1.2 AT2A-2185 WELD ASSY, CHAMBER
2 AT2M-1021-1 PANEL, EGF ACCESS POWER TERMINAL
3 AT2G-1022 GASKET PANEL ACCESS POWER TERMINAL, EG
4 AT2A-3189-1 ASSY, EXT THERM CONTROL PANEL
4.1 AT0E-3336-1 OPERATOR, AB ROTARY SWITCH
4.2 AT0H-1455-2 KNOB FOR D SHAFT
4.3 AT0E-2559-7 TEMPERATURE CONTROLLER, RTD
4.4 AT0E-1800-4 INDICATOR LAMP GRN NEON 250V
4.5 AT0E-1800-5 INDICATOR LAMP RED NEON 250V
4.6 AT0E-3338-1 CONTACT BLOCK
4.7 AT0E-3339-1 MOUNTING LATCH
4.8 AT0F-3371-1 NUT, ROTARY SEAL
5 AT0G-1026-1 GASKET, CONTROL PANEL, EG
6 AT0E-1587-1 3 POLE CONTACTOR
7 AT0E-2662-3 TRANSFORMER
8 AT2A--2916-1 HIGH LIMIT OVER TEMP ASSEMBLY
9 AT2M-1559-1 COVER
10 AT0E-1134-4 4 POSITION TERMINAL BLOCK
11 AT0E-3025-2 INSULATOR STRIP, DOUBLE ROW
16 AT0E-1049-5 CONNECTOR, 1” HUB STRAIN RELIEF
17 AT0A-2788-14 POWER CABLE ASSEMBLY
17.2 AT2E-2567-6 CABLE 6 AWG 4 COND
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 36
MODEL EGF MARITIME MODELS
ITEM NUMBER PART NUMBER DESCRIPTION
18 AT2A-2529-2 GREASE TROUGH ASSY
19 AT2A-2552-2 ASSY, BAFFLED LOCKING GREASE TRAY
19.1 AT0F-1046-41040 SCREW, #10-24X 1/2 PHLP TRUSS HEAD
19.2 AT2M-2551-2 GREASE TRAY FACE PLATE
19.3 AT2M-3008-1 LEVER, GREASE PAN
19.4 AT0F-3012-1 SPACER, ROUND
19.5 AT0F-1052-43010 WASHER, # 10 TYPE B CUSTOM
19.6 AT0F-1922-40000 WASHER, #10 SS HELICAL SPRING LOCK
19.9 AT0F-2632-41001 NUT, A0-24 ACORN
20 AT2A-3032-3 3” LEG ASSEMBLY
21 AT0F-2755-41050 SCREW, #10-24UNC X 5/8 PHILIPS ROUND HEAD MACHINE
22 AT0-1046-31030 SCREW, #8-32 X 3/8 TYPE AB PHILIPS TRUSS HEAD
23 AT0F-2755-41070 SCREW, #10-24UNC X 7/8 PHILIPS ROUND HEAD MACHINE
24 AT0F-2777-31030 SCREW, #8-32 X 3/8 TYPE AB TRUSS HEAD
25 AT0F-2691-41002 NUT, #10-24 NYLOC
26 AT0F-2875-51062 SCREW, 1/4-20UNC X 3/4 HEX HEAD MACHINE
29 AT0F-2778-71001 NUT, 3/8 UNC SS
30 AT0F-2875-71080 SCREW, 3/8-16UNC X 1 HEX HEAD MACHINE
31 AT0H-3184-1 END BRKTS, GRIDDLE GRAB BAR
32 AT2M-3183-2 36” GRIDDLE GRAB
33 AT0F-2755-41040 SCREW, #10-24UNC X 1/2 PHILIPS ROUND HEAD MACHINE
35 AT0E-2885-3 SENSOR REPLACEABLE, RTD
56 AT2A-3227-2 ASSY, 36” GRIDDLE FRONT 36” SKIRT
57 AT2M-3464-5 SKIRT, FRONT 36” MARITIME
56.2 AT0F-2668-1 NUTSERT, 10-24 HEX
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 37
ITEM NUMBER PART NUMBER DESCRIPTION
1 AT2M-3103-1 CHASSIS, RELAY ENCLOSURE
2 AT2M-3104-1 COVER RELAY ENCLOSURE
3 AT0H-2576-1 GROMMET, 7/8 NYLON
4 AT0E-2206-3 HEAT SINK, 3.43” LONG
5 AT0E-2296-1 PAD, SSR HEAT SINK
6 AT0E-2059-3 RELAY SOLID STATE
7 AT0A-3111-1 CONTROL INPUT HARNESS
8 AT0A-3111-2 CONTROL INPUT HARNESS
9 AT0A-3112-4 ASSY, HARNESS
10 AT0A-3112-3 ASY, HARNESS
11 AT0A-3112-2 ASSY, HARNESS
12 AT0A-3112-1 ASSY HARNESS
13 AT0F-2755-31040 SCREW, #8-32UNC X 1/2 PHILLIPS ROUND HEAD MACHINE
14 ATOF-2666-40000 WASHER, #8 INTERNAL TOOTH LOCK
15 AT0F-2755-31040 SCREW, #10-24UNC X 1/2 PHILLIPS ROUND HEAD MACHINE
16 AT0F-2666-40000 WASHER INTERNAL TOOTH LOCK
17 AT0F-1017-41002 NUT, #10-24UNC HEX SERRATED
24 AT0F-2668-1 NUTSERT, #10-24 HEX
MODEL EGF MARITIME MODELS
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 38
C
Title:
Rev.Drawing No.:
ITEM PART NUMBER DESCRIPTION
1 AT2A-3243-1 ASSY, EG CONTROL PANEL WELDMENT
3 AT0E-3336-1 OPERATOR, AB ROTARY SWITCH
4 AT0E-3339-1 MOUNTING LATCH
5 AT0E-3338-1 CONTACT BLOCK
6 AT0E-2559-7 TEMPERATURE CONTROLLER
7 AT0E-1455-2 KNOB FOR D SHAFT
8 AT0E-1800-4 INDICATOR LAMP GRN NEON 250V
9 AT0E-1800-5 INDICATOR LAMP RED NEON 250V
10 AT0E-2715-3 OVERLAY CONTROL PANEL
13 AT2A-3283-1 ASSY, WIRE HARNESS
14 AT2G-1026 GASKET CONTROL PANEL, EG
16 AT0F-3371-1 NUT, ROTARY SHAFT SEAL
CONTROL PANEL MODEL EGF COMMERCIAL & MARITIME AT2A-3189
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 39
ITEM PART NUMBER DESCRIPTION
1 AT2M-2861-1 WIRE ROD, OVER TEMP
2 AT2M-2860-1 SOLDER WASHER OVER TEMP
3 AT0F-1367-1 WASHER, TYPE A
4 AT2H-1365-1 COMPRESSION SPRING
5 AT2M-1558-2 BRACKET SWITCH
6 AT2H-1640-1 EXTENSION SPRING
7 AT2E-1639-1 MICRO-SWITCH
8 AT0F-2691-21002 NUT, #6-32 NYLOC
9 AT0F-1052-51002 WASHER 1/4 TYPE B PLAIN ZINC PLATED
10 AT0F-2755-21102 SCREW, #6-32UNC X 1 1/4 PHILI ROUND HEAD MACHINE
11 AT0F-1017-41002 NUT, #10-24UNC HEX SERRATED
HIGH LIMIT OVER TEMP ASSEMBLY MODEL EGF COMMERCIAL & MARITIMEAT2A-2916-1
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 40
SERVICE PARTSMODEL EGD
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 41
17
15
1234
14
9
35
2
75
8
6
8
1
33
3
11
34
35
3413
30
31
37
36
33
2625 28 28 22 19
3
16
40
41
32
4
33
42
33
MODEL EGD DROP-IN ASSEMBLY AT2A-2520
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 42
ITEM NUMBER PART NUMBER DESCRIPTION
1 AT2A-2514-2 DROP IN GRIDDLE ASSEMBLY-MODEL EGD2083B36
1A AT2A-2514-3 DROP IN GRIDDLE ASSEMBLY-MODEL EGD2083B48
1B AT2A-2514-5 DROP IN GRIDDLE ASSEMBLY-MODEL EGD2403B36, EGD4403B36, EGD4803B36
1C AT2A-2514-6 DROP IN GRIDDLE ASSEMBLY-MODEL EGD2403B48, EGD4403B48, EGD4803B48
2 AT2A-2533-1 BOTTOM PAN ASSY-MODEL EGD2083B36, EGD2403B36, EGD4403B36, EGD4803B36
2A AT2A-2533-2 BOTTOM PAN ASSY-MODEL EGD2083B48, EGD2403B48 EGD4403B48, EGD4803B48
3 AT2E-2700-1 TERMINAL INSULATOR
3A AT2E-2700-2 TERMINAL INSULATOR-MODEL EGD2083B48, EGD2403B48 EGD4403B48, EGD4803B48
4 AT2A-2916-2 HIGH LIMIT OVERTEMP ASSEMBLY
5 AT2I-2523-2 INSULATION-MODEL EGD2083B36, EGD2403B36, EGD4403B36, EGD4803B36
1 AT2A-2514-2 DROP IN GRIDDLE ASSEMBLY-MODEL EGD2083B36
1A AT2A-2514-3 DROP IN GRIDDLE ASSEMBLY-MODEL EGD2083B36
1B AT2A-2514-5 DROP IN GRIDDLE ASSEMBLY-MODEL EGD2083B36
1C AT2A-2514-6 DROP IN GRIDDLE ASSEMBLY-MODEL EGD2083B36
2 AT2A-2533-1 BOTTOM PAN ASSY-MODEL EGD2083B36, EGD2403B36, EGD4403B36, EGD4803B36
2A AT2A-2533-2 BOTTOM PAN ASSY-MODEL EGD2083B48, EGD2403B48 EGD4403B48, EGD4803B48
3 AT2E-2700-1 TERMINAL INSULATOR
3A AT2E-2700-2 TERMINAL INSULATOR-MODEL EGD2083B48, EGD2403B48 EGD4403B48, EGD4803B48
4 AT2A-2916-2 HIGH LIMIT OVERTEMP ASSEMBLY
5 AT2I-2523-2 INSULATION-MODEL EGD2083B36, EGD2403B36, EGD4403B36, EGD4803B36
5A AT2I-2523-3 INSULATION-MODEL EGD2083B48, EGD2403B48, EGD4403B48, EGD4803B48
6 AT2I-2523-5 INSULATION-MODEL EGD2083B36, EGD2403B36, EGD4403B36, EGD4803B36
6A AT2I-2523-6 INSULATION-MODEL EGD2083B48, EGD2403B48, EGD4403B48, EGD4803B48
7 AT2I-2523-7 INSULATION-MODEL EGD2083B36, EGD2403B36, EGD4403B36, EGD4803B36
8A AT2I-2523-9 INSULATION-MODEL EGD2083B36, EGD2403B36, EGD4403B36, EGD4803B36
8B AT2I-2523-10 INSULATION-MODEL EGD2083B48, EGD2403B48, EGD4403B48, EGD4803B48, EGD2083B48, EGD2403B48, EGD4403B48, EGD4803B48
9 AT2A-2577-4 CONTROL BOX ASSEMBLY
11 AT2M-1559-2 COVER
12 AT0E-1049-1 CONNECTOR, 1 1/4” HUB STRAIN RELIEF-MODEL EGD2083B36, EGD2083B48 EGD2403B36, EGD2403B48
12A AT0E-1049-2 CONNECTOR, 3/4” HUB STRAIN RELIEF-MODEL EGD4403B36, EGD4803B36, EGD4403B36, EGD4803B48
13 AT0A-2736-5 MOV- TERMINALS ASSEMBLY-MODEL EGD2083B36, EGD2083B48 EGD2403B36, EGD2403B48
MODEL EGD DROP-IN ASSEMBLY AT2A-2520
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 43
ITEM NUMBER PART NUMBER DESCRIPTION
13A AT0A-2736-6 MOV- TERMINALS ASSEMBLY-MODEL EGD4403B36, EGD4803B36, EGD4403B36, EGD4803B48
14 AT0E-2086-2 CORD GRIP LOCKNUT-MODEL EGD4403B36, EGD4803B36, EGD4403B36, EGD4803B48
14A AT0E-2086-4 CORD GRIP LOCKNUT-MODEL EGD2083B36, EGD2083B48 EGD2403B36, EGD2403B48
15 AT0A-2788-1 POWER CABLE ASSY-MODEL EGD2083B36, EGD2083B48 EGD2403B36, EGD2403B48
15A AT0A-2788-3 POWER CABLE ASSY-MODEL EGD4403B36, EGD4803B36, EGD4403B36, EGD4803B48
16 AT2L-2713-7 SCHEMATIC LABEL, GRIDDLE-MODEL EGD2083B36, EGD2083B48 EGD2403B36, EGD2403B48,
16A AT2L-2713-9 SCHEMATIC LABEL, GRIDDLE MODEL EGD4403B36, EGD4803B36, EGD4403B36, EGD4803B48
17 AT0L-2798-1 OVERLAY, WARNING, ELECTRICAL
18 AT0A-2617-7 25.0” HIGH TEMP WIRE ASSEMBLY WHITE-MODEL EGD2083B36, EGD2403B36, EGD4403B36, EGD4803B36
19 AT0A-2617-9 29.0” HIGH TEMP WIRE ASSEMBLY WHITE-MODEL EGD2083B36, EGD2403B36, EGD4403B36, EGD4803B36
20 AT0A-2617-11 34.0” HIGH TEMP WIRE ASSEMBLY WHITE-MODEL EGD2083B48, EGD2403B48, EGD4403B48, EGD4803B48
21 AT0A-2617-6 23.0” HIGH TEMP WIRE ASSEMBLY WHITE-MODEL EGD2083B48, EGD2403B48, EGD4403B48, EGD4803B48
22 AT0A-2617-8 27.0” HIGH TEMP WIRE ASSEMBLYWHITE- MODEL EGD2083B36, EGD2403B36, EGD4403B36, EGD4803B36
23 AT0A-2617-10 32.0” HIGH TEMP WIRE ASSEMBLY WHITE-MODEL, EGD2083B48, EGD2403B48, EGD4403B48, EGD4803B48
25 AT0A-2617-4 12.0” HIGH TEMP WIRE ASSEMBLY WHITE-MODEL EGD2083B36, EGD2083B48 EGD2403B36, EGD2403B48, EGD4403B36, EGD4803B36, EGD4403B36, EGD4803B48
26 AT0A-2617-5 14.0” HIGH TEMP WIRE ASSEMBLY WHITE-MODEL EGD2083B36, EGD2083B48 EGD2403B36, EGD2403B48, EGD4403B36, EGD4803B36, EGD4403B36, EGD4803B48
28 AT0A-2617-13 21.0” HIGH TEMP WIRE ASSEMBLY WHITE-MODEL EGD2083B36, EGD2083B48 EGD2403B36, EGD2403B48, EGD4403B36, EGD4803B36, EGD4403B36, EGD4803B48
30 AT2A-2758-2 CABLE ASSEMBLY OT-EGD2083B36, EGD2403B36, EGD4403B36, EGD4803B36
30A AT2A-2758-3 CABLE ASSEMBLY OT-MODEL EGD2083B48, EGD2403B48, EGD4403B48, EGD4803B48
31 AT2L-3725-1 DATA TAG, ELECTRIC GRIDDLE
32 AT0F-1017-41002 NUT, #10-24UNC HEX SERRATED
33 AT0F-2755-41040 SCREW, #10-24UNC X 1/2 PHILIPS ROUND HEAD MACHINE
34 AT0F-2777-31030 SCREW, #8 TYPE AB X 3/8 TRUSS HD
35 AT0F-2755-31030 SCREW, #8-32UNC X 3/8 PHILIPS ROUND HEAD MACHINE
36 AT0F-2666-40000 WASHER, #10 INTERNAL TOOTH LOCK
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 44
ITEM NUMBER PART NUMBER DESCRIPTION
37 AT0F-2778-41001 NUT, #10-24UNC-2B SS HEX MACHINE SCREW
38 AT2M-2768-1 PLATE, ADAPTER
39 AT0F-2755-21020 SCREW, #6-32UNC X 1/4 PHILIPS ROUND HEAD MACHINE
40 AT0H-2576-2 GROMMET, 1¼” NYLON
41 AT0E-2885-5 SENSOR, REPLACEABLE
42 AT2M-2646-1 COVER CONTROL BOX
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 45
MODEL EGD DROP-IN GRIDDLE CONTROL BOX ASSEMBLY AT2A-2577
ITEM PART NUMBER DESCRIPTION
1 AT2M-2560-3 BOX, CONTROL
2 AT0E-1587-4 3 POLE CONTACTOR
4 AT0E-1134-4 4 POSITION TERMINAL BLOCK
5 AT0E-3025-2 INSULATOR STRIP, 4 POSITION DOUBLE ROW
6 AT0E-2708-1 3AG OMNI-BLOK FUSE BLOCK 2 POS
7 AT0E-2731-2 FUSE 1¼ AMP 250V
8 AT0E-2662-5 TRANSFORMER
9 AT0A-2736-8 MOV- TERMINALS ASSEMBLY
10 AT0H-2887-1 CABLE TIE MOUNT
11 AT0E-2206-3 HEAT SINK, 3.47” LONG
12 AT0E-2059-3 RELAY, SOLID STATE
14 AT0F-2755-21020 SCREW, #6-32UNC X 1/4 PHILIPS ROUND HEAD MACHINE
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 46
MODEL EGD DROP-IN GRIDDLE CONTROL BOX ASSEMBLY AT2A-2577
ITEM PART NUMBER DESCRIPTION
15 AT0F-2755-21050 SCREW, #6-32UNC X 5/8 PHILIPS ROUND HEAD MACHINE
16 AT0F-2777-31030 SCREW, #8 TYPE AB X 3/8 TRUSS HD
17 AT0F-2755-31030 SCREW, #8-32UNC X 3/8 PHILIPS ROUND HEAD MACHINE
18 AT0F-2755-41020 SCREW, #10-24UNC X 1/4 PHILIPS ROUND HEAD MACHINE
19 AT0F-2755-41050 SCREW, #10-24UNC X 5/8 PHILIPS ROUND HEAD MACHINE
20 AT0F-2755-41052 SCREW, #10-24UNC X 5/8 PHILIPS ROUND HEAD MACHINE
21 AT0F-1017-41002 NUT, #10-24UNC HEX SERRATED
22 AT0F-2668-1 NUTSERT, #10-24 HEX
23 AT0F-2666-30000 #8 LOCK WASHER INTERNAL TOOTH
24 AT0A-2761-1 CABLE GROUND WIRE ASSY
25 AT0A-2615-2 WIRE HARNESS
26 AT0A-2615-3 WIRE HARNESS
27 AT0A-2615-5 WIRE HARNESS
28 AT0A-2617-1 5.0” HIGH TEMP WIRE ASSEMBLY WHITE
29 AT2A-2760-6 CABLE ASSEMBLY
30 AT0A-2617-3 5.0” HIGH TEMP WIRE ASSEMBLY RED
31 AT0A-2617-31 6.0” HIGH TEMP WIRE ASSEMBLY RED
32 AT0A-2617-32 7.0” HIGH TEMP WIRE ASSEMBLY BLACK
33 AT0A-2617-33 8.0” HIGH TEMP WIRE ASSEMBLY BLACK
34 AT0A-3178-1 HARNESS ASSEMBLY FORK TERM TO FORK TERM
35 AT0A-3178-2 HARNESS ASSEMBLY FORK TERM TO FORK TERM
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 47
21
3
6
23
7
20
18
16
19
1
4
14
5
22
9
11
10
17
2
24
ITEM NUMBER PART NUMBER DESCRIPTION
1 AT2A-2592-1 1” GREASE SPOUT EXTENSION
2 AT2A-2592-2 2” GREASE SPOUT EXTENSION
3 AT2A-2592-3 3” GREASE SPOUT EXTENSION
4 AT2A-2592-4 4” GREASE SPOUT EXTENSION
5 AT2A-2529-1 GREASE TROUGH ASSY
5A AT2A-2529-3 GREASE TROUGH ASSY
6 AT2A-2552-1 GREASE TRAY ASSEMBLY
6A AT2A-2552-3 ASSY, LONG BAFFLED LOCKING GREASE TRAY
7 AT2A-2764-1 CABLE ASSEMBLY
9 MP5004 ELECTRIC GRIDDLE OWNERS MANUAL
10 AT2M-2553-1 GREASE TROUGH HNGR BRKT
11 AT2M-2554-1 GREASE TROUGH HANGER
14 AT0L-2716-1 OVERLAY, LOGO, ACCUTEMP
16 AT0F-2777-41040 SCREW, #10 TYPE AB X 1/2 TRUSS HD
17 AT0F-2755-41040 SCREW, #10-24UNC X 1/2 PHILIPS ROUND HEAD MACHINE
18 AT0F-1921-61060 BOLT, 5/16-18 UNC 2A X 3/4” CARRIAGE
19 AT0F-1922-60000 WASHER, 5/16” HELICAL SPRING LOCK
20 AT0F-2778-61000 NUT, 5/16-18UNC-2B SS HEX MACHINE SCREW
21 AT0F-2691-51002 NUT, ¼-20 NYLOC
22 AT2M-2535-1 RETAINER BRACKET
23 AT0F-2666-40000 WASHER, #10 INTERNAL TOOTH LOCK
24 AT0T-3033-1 PRODUCT REGISTRATION FORM
MODEL EGD DROP-IN GRIDDLE LOOSE PIECE KIT AT2A-2772
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 48
AT2A-2526-5CONTROL PANEL ASSY - RH
OTHERWISE SAME AS AT2A-2526-4
1
18
AT2A-2526-4
1
17
CONTROL PANEL ASSY - FULLOTHERWISE SAME AS AT2A-2526-1
G
G19
2
AT2A-2526-4CONTROL PANEL ASSY - FULL
5 9 11
F
121
15
7
8
4
16
3
6 11
OTHERWISE SAME AS AT2A-2526-4CONTROL PANEL ASSY - LH
AT2A-2526-6
1
ITEM NUMBER PART NUMBER DESCRIPTION
1 AT2A-2565-1 CONTROL PANEL WELD ASSY - FULL
1A AT2A-2565-2 CONTROL PANEL WELD ASSY- RH
1B AT2A-2565-3 CONTROL PANEL WELD ASSY - LH
2 AT2M-2566-1 CONTROL PANEL COVER
3 AT2M-2566-1 KNOB FOR D SHAFT
4 AT0E-3336-1 OPERATOR, AB ROTARY SWITCH
5 AT0E-3338-1 CONTACT BLOCK
6 AT0E-3339-1 MOUNTING LATCH
7 AT0E-1800-1 INDICATOR LAMP GRN LED 28V
8 AT0E-1800-2 INDICATOR LAMP RED LED 28V
10 AT2A-2762-1 HARNESS ASSEMBLY
11 AT0F-2691-41002 NUT, #10-24 NYLOC
12 AT0F-2777-31030 SCREW, #8 TYPE AB X 3/8 TRUSS HD
15 AT2L-2715-1 OVERLAY, CONTROL PANEL
16 AT2M-2907-1 THERMOSTAT GUARD BRKT
17 AT2A-2762-2 HARNESS ASSEMBLY
18 AT0E-2559-6 TEMPERATURE CONTROLLER
19 AT0F-3371-1 NUT, ROTARY SHAFT SEAL
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 49
ITEM PART NUMBER DESCRIPTION
1 AT2M-2861-1 WIRE ROD, OVER TEMP
2 AT2M-2860-1 SOLDER WASHER OVER TEMP
3 AT0F-1367-1 WASHER, TYPE A
4 AT2H-1365-1 COMPRESSION SPRING
5 AT2M-1558-2 BRACKET SWITCH
6 AT2H-1640-1 EXTENSION SPRING
7 AT2E-1639-1 MICRO-SWITCH
8 AT0F-2691-21002 NUT, #6-32 NYLOC
9 AT0F-1052-51002 WASHER 1/4 TYPE B PLAIN ZINC PLATED
10 AT0F-2755-21102 SCREW, #6-32UNC X 1 1/4 PHILI ROUND HEAD MACHINE
11 AT0F-1017-41002 NUT, #10-24UNC HEX SERRATED
HIGH LIMIT OVER TEMP ASSEMBLY EGD MODELSAT2A-2916-1
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 50
SCHEMATICSMODEL EGF
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 51
ACCUSTEAM ELECTRIC SERIES SCHEMATICMODEL EGF
208/240V 3 PHASE
AT2T-3640-1 REV A
Size (inches) Voltage Ohms
24 208 13.52
24 240 18
36 & 48 208 9.11
36 & 48 240 12.13
ELEMENT SPECIFICATION
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 52
ACCUSTEAM ELECTRIC SERIES SCHEMATICMODEL EGF
240V SINGLE PHASE
AT2T-3640-2 REV A
Size (inches) Voltage Ohm
24 240 18
ELEMENT SPECIFICATION
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 53
ACCUSTEAM ELECTRIC SERIES SCHEMATICMODEL EGF
440V/480V 3-PHASE
AT2T-3640-4 REV A
ELEMENT SPECIFICATION
Size (inches) Voltage Ohm
24 440 13.52
24 480 18
36 & 48 440 9.11
36 & 48 480 12.13
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 54
ACCUSTEAM ELECTRIC SERIES SCHEMATICMODEL EGF
380V-435V 5 WIRE
AT2T-3640-3 REV A
ELEMENT SPECIFICATION
Size (inches) Voltage Ohms per Element
24 380 18
24 415 18
24 440 18
24 480 18
36 & 48 380 9.11
36 & 48 415 12.13
36 & 48 440 12.13
36 & 48 480 12.13
Accu-Steam™ Installation and Owners ManualMP5004-1605
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 55
SERVICE PARTSMODEL EGD
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 56
L
OR
N
YE
L
RED
WHT
BLK
GRN
WHT
WHT
BLK
BLUBLU
BLK
FINAL SELECTION OF PRIMARY VOLTAGE TO BE MADE IN FINAL ASSEMBLY
480V
440V
240V
208V
COM
AT0E-2662-5
24V
F1
F23AG .5A
AT0E-2731-1
41
26
3
L3
L1
L2
5
BLK
WHT
RED
N
R1 R3
R2
ZR2
WHT
RED
BLK
ZR1
RED
AT2E-1587-4
AT0E-2736-5
AT0E-2736-8
RLY 1
ZR4
L3
L2
L1
WHT
SSR 1 SSR 2
1 P
3 2
1 J3
2SW2
O.T. SW
N.O.
N.C.
1 P
4 2
1 J4
2
RED
RED
BLK
BLKAT2A-2916-2
AT0A-2758-1
1 P5 2
1 J5 2
WHT
1 2 3 4 5 6 7J2
1 2 3 4 5 6 7P1
P21 2 3 4 5 6 7
WH
T
RE
D
OR
N
RED
BLK WHT
ORN
GRNBLU
WHT/BLK
GR
N
CONTROL PANEL
BLK CONTACTOR
ENCLOSURE
AT2A-2764-1
AT2A-2760-5
AT0A-2761-1
YEL
RED
J11 2 3 4 5 6 7
ON/OFFSW1 PWR
LT1HEATLT2
BLK
RED
WHT
ORN
YE
L
CONTROL PANEL
AT2E-1755 AT0E-1800-1 AT0E-1800-2
AT2A-2762-2
BLU BLU
PRTD
RED RED
WHT
OR
N
1 3 5 6 8 9 L1 L2 OUTPUT PRTD
PRTD TYPE CONTROLLER CAL OFFSET ADJ
to
ANALOG CONTROLER
MODEL EGD DROP-IN 208/240V DELTA SSR HEATER CONFIGURATIONAT2T-2713-7
Size (inches) Voltage Ohm
24 208 13.52
24 240 18
36 & 48 208 9.11
36 & 48 240 12.13
ELEMENT SPECIFICATION
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 57
OR
N
YEL
RED
WHT
BLK
GRN
WHT
WHT
BLK
BLUBLU
BLK
FINAL SELECTION OF PRIMARY VOLTAGE TO BE MADE IN FINAL ASSEMBLY
480V
440V
240V
208V
COM
AT0E-2662-5
24V
F1
F23AG .5A
AT0E-2731-1
BLK
WHT
RED
ZR2
WHT
RED
BLK
ZR1
RED
AT2E-1587-4
AT0E-2736-5
AT0E-2736-8
RLY 1
ZR4
L3
L2
L1
WHT
SSR 1 SSR 2
1 P3
2
1 J3
2
SW2O.T. SW
N.O.
N.C.
1 P4
2
1 J4
2
RED
RED
BLK
BLK
AT0A-2758-1
1 P5 2
1 J5 2
WHT
1 2 3 4 5 6 7J2
1 2 3 4 5 6 7P1
P21 2 3 4 5 6 7
WH
T
RED
OR
N
RED
BLK WHT
ORN
GRNBLU
WHT/BLK
GR
N
BLK
CONTACTOR ENCLOSURE
AT2A-2764-1
AT2A-2760-5
AT0A-2761-1
YEL
RED
J11 2 3 4 5 6 7
ON/OFFSW1 PWR
LT1HEATLT2
BLK
RED
WHT
ORN
YEL
CONTROL PANEL
AT0E-1800-1 AT0E-1800-2
AT2A-2762-2
BLU BLU
PRTD
RED RED
WHT
OR
N
1 3 5 6 8 9 L1 L2 OUTPUT PRTD
PRTD TYPE CONTROLLER CAL OFFSET ADJ
to
ANALOG CONTROLER
BLK
WHT
RED
R1 R3
R2
5
1
6
3
L3
L1
L2
N4 2
MODEL EGD DROP-IN 440/480V WYE SSR HEATER CONFIGURATIONAT2T-2713--8
Size (inches) Voltage Ohm
24 208 13.52
24 240 18
36 & 48 208 9.11
36 & 48 240 12.13
ELEMENT SPECIFICATION
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 58
OR
N
YE
L
WHT
BLK
GRN
WHT
WHT
BLK
BLUBLU
BLK
FINAL SELECTION OF PRIMARY VOLTAGE TO BE MADE IN FINAL ASSEMBLY
480V
440V
240V
208V
COM
AT0E-2662-5
24V
F1
F23AG .5A
AT0E-2731-1
BLK
WHT
WHT
BLK
ZR1
RED
AT2E-1587-4
AT0E-2736-5
AT0E-2736-8
RLY 1
ZR4
L3
L2
L1
WHT
SSR 1
1 P
3 2
1 J3
2
SW2O.T. SW
N.O.
N.C.1
P4
2
1 J4
2
RED
RED
BLK
BLK
AT0A-2758-1
1 P5 2
1 J5 2
WHT
1 2 3 4 5 6 7J2
1 2 3 4 5 6 7P1
P21 2 3 4 5 6 7
WH
T
RE
D
OR
N
RED
BLK WHT
ORN
GRNBLU
WHT/BLK
WH
T
GR
N
CONTROL PANEL
BLK CONTACTOR
ENCLOSURE
AT2A-2764-1
AT2A-2760-5
AT0A-2761-1
YEL
RED
J11 2 3 4 5 6 7
ON/OFFSW1 PWR
LT1HEATLT2
BLK
RED
WHT
ORN
YE
L
CONTROL PANEL
AT0E-1800-1 AT0E-1800-2
AT2A-2762-2
BLU BLU
PRTD
RED RED
WHT
OR
N
1 3 5 6 8 9 L1 L2 OUTPUT PRTD
PRTD TYPE CONTROLLER CAL OFFSET ADJ
to
ANALOG CONTROLER
R1 R3R2
1
4
2
3
L3
L1
L2
BLK
5
6WHT
N
MODEL EGD DROP-IN 240V SINGLE PHASE SSR HEATER CONFIGURATIONAT2T-2713-9
Size (inches) Voltage Ohm
24 208 13.52
24 240 18
36 & 48 208 9.11
36 & 48 240 12.13
ELEMENT SPECIFICATION
Accu-Steam™ Installation and Owners ManualMP5004-1605 PAGE 59
AccuTemp Products, Inc. ( AccuTemp ) warrants that your AccuTemp equipment will be free of defects in material andworkmanship under normal use for a period of twelve (12) months from installation or fifteen (15) months from date of shipmentfrom AccuTemp, whichever date first occurs (the Warranty Period ). Registration of AccuTemp equipment is required at timeof installation.
Damage to AccuTemp equipment that occurs during shipment must be reported to the carrier, and is not covered under this warranty.The reporting of any damage during shipment is the sole responsibility of the commercial purchaser/user of such AccuTempequipment.
AccuTemp provides an active service department, which should be contacted and advised of service issues regardless of warrantyperiod.
During the warranty period, AccuTemp agrees to repair or replace, at its option, F.O.B. factory, any part which proves to be defectivedue to defects in material or workmanship, provided the equipment has not been altered in any way and has been properly installed,maintained, and operated in accordance with the instructions in the AccuTemp Owners Manual.
During the warranty period, AccuTemp also agrees to pay for any factory authorized equipment service agency (within the continentalUnited States and Canada) for reasonable labor required to repair or replace, at our option, F.O.B. factory, any part which proves tobe defective due to defects in materials or workmanship, provided the service agency has received advance approval from AccuTempfactory service to perform the repair or replacement. This warranty includes travel time not to exceed two hours and mileage not toexceed 50 miles (100 miles round trip), but does not include post start-up assistance or training, tightening of loose fittings or externalelectrical connections, minor adjustments, maintenance, or cleaning. AccuTemp will not reimburse the expense of labor requiredto replace parts after the expiration of the warranty period.
Proper installation is the responsibility of the dealer, owner-user, or installing contractor and is not covered by this warranty. WhileAccuTemp products are built to comply with applicable standards for manufacturers, including Underwriters Laboratories (UL) andNational Sanitation Foundation (NSF), it is the responsibility of the owner and the installer to comply with any applicable local codesthat may exist.
AccuTemp makes no other warranties or guarantees, whether expressed or implied, including any warranties of performance,merchantability, or fitness for any particular purpose. AccuTemp s liability on any claim of any kind, including negligence, withrespect to the goods and services covered hereunder, shall in no case exceed the price of the goods and services, or parts thereof,which gives rise to the claim. In no event shall AccuTemp be liable for special, incidental, or consequential damages, or damages inthe nature of penalties.
This constitutes the entire warranty, which supersedes and excludes all other warranties, whether written, oral, or implied.
IMPORTANTImproper installation can affect your warranty. Installation is the responsibility of the Dealer, Owner/User or the Installation Contractor.See: Section One, Installation of the Owner s Manual.
For Service Call 800-480-0415
Call 800 210-5907
Product Warranty
U.S. & Canada Sales Only
LIMITED WARRANTYOne Year Parts and Labor
MM6311-0601
Accu-Steam™ Installation and Owners ManualMP5004-1605
INFORMATION
IMPORTANT SERVICE INFORMATIONAccuTemp Product, Inc. Technical & Customer Support Technician is
available Monday thru Sunday, 7:00am to 7:00pm EST
800 480-0415 or 260 469-3040
• Phone - 800 480-0415 or 260 469-3040• Fax - 260 469-3045• Email - [email protected]• Web site - www.accutemp.net