ensol solar collectors catalogue
TRANSCRIPT
Der Kollektor E-PVT 2,0 ist eine Kombination von einem Flach Sonnenkollektor mit einem polykristallin PV-Mo-dul mit einer Leistung von 300 W.
Der Sonnenkollektor ist verantwortlich für die Verwandlung der Sonnenstrah-
lung auf Wärmeenergie zur unterstützung von Warmwasser und Leitungswasser.
Das PV-Modul verwandelt Sonnenstrahlung in Elektrizität.
Erwärmung von PV-Modulen verringert Ihre Leistung, und wird um c.a 0,5% Ge-
ringerer bei zuhname der Temperatur um jedem Grad. Die Leistungscharakteri-
stik, die im Technischen Daten angegeben wird, bezieht sich auf eine Modul
Temperatur, die 25 ºC beträgt.
Durch die Instalation von einen Thermischen System im den Hybrid Kollek-
tor PVT erfolgt ein wärme Empfang durch ein Kühlmittel der im den Kollek-
tor fließt. Durch den wärme Empfang aus den Thermischen Teil des Kollektor
steigt die Elektrische Leistung des PV-Modul. Der Hybrid Kollektor E-PVT 2,0
ist eine Technologische Entwicklung im Bereich von erhöhung der Leistung
von PV Modulen bei einer gleichzeitigen verwandlung der Sonnenstrahlener-
gie auf Wärme Energie und Elektrizität.
Vorteile des Hydbrid Kollektor E-PVT 2,0:
» höhere Effizienz der produzierten Elektrischer Energie im vergleich zu standard PV-Modulen,
» Thermischer Teil des Sonnenkollektor dient zur erwärmung von Warmwas-ser und zu unterstützung von Heisen Leitungswasser,
» Einsparung von Dachfläche und Montagekosten,
» höhere ökonomische und wirtschaftliche möglichkeiten – ein Kollektor erzeugt sowohl Strom als auch Wärme,
» geringere Investitionskosten der Anlage als bei traditionellen Geräten (Sonnenkollektor und PV-Modul).
E-PVT 2,0/
Collector E-PVT 2,0 is a combination of a flat solar col-lector and photovoltaic module with polycrystalline silicon cell with power of 300 W.
By bionic exchanger waste heat is used for domestic hot water or central heat-
ing, photovoltaic module converts the solar energy into electricity.
Photovoltaic module defined as a source of a pure electric energy is not
without downsides; its efficiency lowers when the temperature of the module
rises. When the temperature of cells goes up by 1 K, its capacity of producing
energy goes down by 0,5%. Catalogue parameters of photovoltaic modules are
given for the temperature of a module equal 25 degrees, with an insolation
of 1000 W/m2. During the work in a full, lasting for several hours insola-
tion, the temperature of a module rises to a level which could cause the
loss of efficiency reaching even 40%.
By using thermal system in a hybrid collector PVT occurs a reception of
warmth with the use of cooling fluid flowing by Roll-Bond exchanger.
By removing the heat, thermal system increases the capacity to process
solar radiation into electric current, but also provides a lot of thermal
energy. Hybrid collector E-PVT2,0 is a technological progress in in-
creasing efficiency of photovoltaic modules with a simultaneous ex-
change of a solar energy into thermal and electric energy.
Advantages of a hybrid collector E-PVT2,0:
» higher efficiency of production of electric energy in compari-son to standard photovoltaic modules,
» thermal part of a collector is used for heating domestic water and supporting central heating,
» more economic possibilities – one module required for pro-duction of electrical current and heat,
» lower investment cost of both systems than in traditional devices (fluid thermal collectors and photovoltaic mod-ules).
HERSTELLER von Sonnenkollektoren
E-PV T 2,0 | H YBRI D KOL L EK TOR
Flachkollektor / Flat solar collector Wert / value
Breite / width 1006 mm
Höhe / height 2007 mm
Tiefe / depth 85 mm
Masse / weight 37 kg
Fläche / surface 2,02 m2
Gehäuse / housingpatentiertes Aluminiumprofil /
patented aluminium profile
Technische Daten / technical parameters
Absorberart / absorber’s typeRoll-Bond Wärmetauscher
aus Aluminium / Aluminium exchanger Roll-Bond
Selektive Schicht / selective layer Blue Tec eta plus / Blue Tec eta plus
Powierzchnia apertury / aperture surface 1,86 m2
Breite / width 954 mm
Höhe / height 1959 mm
Kollektorleistung / collector efficiency 55,5 %
Beiwert bu / Coefficent b
u0,051 W/(m2K2)
Beiwert b1a
/ Coefficent b1a
9,547 W/(m2K2)
Beiwert b2a
/ Coefficent b2a
1,389 W/(m2K2)
max. Arbeitsdruck / maximum operating pressure
6 bar
max. Arbeitstemperatur / maximum operating temp.
85 oC
Flüssigkeitsvolumen / fluid content 1,2 dm3
Elektrische Parameter / electrical parameters
Nennleistung (bei 1000 W/m2)/ Peak power (for 1000 W/m2)
300 W
Zellen typ / type of cell Polykristalline / policrystalline
Zellen / amount of cells 72
Zellen größe/ size od cells 156 x 156 mm
Nennstrom / rated current 8,15 A
Kurzschlussstrom / short-circuit current 8,75 A
Nennspannung / nominal voltage 36,82 V
Leerlaufspannung/ open-circuit viltage
45,31 V
Gesamt Spitzenleistung (bei 1000 W/m2) / Total peak Power (for 1000 W/m2)
1175 W
Dru
ckve
rlust
[kPa]
/ p
ressuer
dro
p [
kPa]
Druckverlust bei Durchfluss durch 1 Kollektor / Pressure loss depending on the flow rate
0 100 15050 200 250 300 350 400 4500
20
10
30
50
40
60
70
5000 100 15050 200 250 300 350 400 4500
20
10
30
50
40
60
Przepływ płynu w dm3/h / Fluid flow in dm3/h
0 5 10 15 20 25 30 35 40
-200
-400
0
200
400
600
800
1000
1200
(tm-ta) [K]
Therm
ische L
eis
tung [
W]
/ t
herm
al
pow
er
[W]
Kollektor Leistung (dla G=1000 W/m2) / Collector efficiency (for G=1000 W/m2)
10001000
-200
00
200
400
600
800
u=0,5 m/s u=1,5 m/s u=3 m/s
1006 85
30
19
98
18
90
49 41
ø22
ø22
Koll
ekto
r E
inla
uf
mit
Kalt
en M
ediu
m /
Feedin
g o
f th
e c
oll
ecto
r w
ith t
he c
old
w
ork
ing s
ubsta
nce (
inta
ke)
Koll
ekto
r R
ückla
uf
mit
Warm
en M
ediu
mzum
nahste
n K
oll
ekto
r oder
Speic
her
/Ta
ke o
ff o
f th
ew
arm
ed f
acor
into
th
e n
ext
coll
ecto
r of
the c
onta
iner
MANUFACTURER of solar collectors
E-PV T 2,0 | H YBR I D COLLECTOR