Upload File

evaluation note eval-adv7630ebz rev. b · eval note rev. a page 5 of 30 1. introduction this...

  • Home
  • Documents
  • Evaluation Note EVAL-ADV7630EBZ Rev. B · Eval Note Rev. A Page 5 of 30 1. Introduction This evaluation note is intended to provide application support for the ADV7630 evaluation
30
Eval Note ADV7630 Eval Note Rev.A Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. Evaluation Note EVAL-ADV7630EBZ Rev. B December 2013 Rev.A

Upload: others

Post on 21-Sep-2020

3 views

Category:

Documents


0 download

Report

TRANSCRIPT

Page 1: Evaluation Note EVAL-ADV7630EBZ Rev. B · Eval Note Rev. A Page 5 of 30 1. Introduction This evaluation note is intended to provide application support for the ADV7630 evaluation

Eval Note ADV7630 Eval Note

Rev.A Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners.

Evaluation Note

EVAL-ADV7630EBZ Rev. B

December 2013

Rev.A

Page 2: Evaluation Note EVAL-ADV7630EBZ Rev. B · Eval Note Rev. A Page 5 of 30 1. Introduction This evaluation note is intended to provide application support for the ADV7630 evaluation

Eval Note

Rev. A Page 2 of 30

Page 3: Evaluation Note EVAL-ADV7630EBZ Rev. B · Eval Note Rev. A Page 5 of 30 1. Introduction This evaluation note is intended to provide application support for the ADV7630 evaluation

Eval Note

Rev. A Page 3 of 30

Table of Contents

Table of Contents ........................................................................................................................................................... 3

1. Introduction ......................................................................................................................................................... 5

2. Evaluation Kit ....................................................................................................................................................... 5

3. Initial Hardware Configuration ............................................................................................................................ 5

3.1 DVP Eval Installation ........................................................................................................................................ 6

3.2 Loading/Unloading Boards ............................................................................................................................ 10

3.2.1 Loading a Board ....................................................................................................................................... 10

3.2.2 Unloading a Board ................................................................................................................................... 11

3.3 Running Scripts .............................................................................................................................................. 12

3.4 Other DVP Eval Features ................................................................................................................................ 13

3.4.1 Register Control ....................................................................................................................................... 13

4. The ADV7630 Evaluation Platform in Depth ...................................................................................................... 14

4.1 Hardware Overview ....................................................................................................................................... 14

4.1.1 Connectors .............................................................................................................................................. 14

4.1.2 Jumpers ................................................................................................................................................... 14

4.1.3 Switches & Buttons .................................................................................................................................. 15

4.1.4 Miscellaneous .......................................................................................................................................... 15

4.2 Using the ADV7630 Evaluation Platform ....................................................................................................... 16

4.2.1 Connecting an Input Video Source .......................................................................................................... 16

4.2.2 Connecting to a Video Sink ..................................................................................................................... 16

4.2.3 Updating the Software Driver .................................................................................................................. 16

4.2.4 Interfacing with the Software Driver ....................................................................................................... 17

5. Appendix 1 – Schematics ................................................................................................................................... 18

6. Appendix 2 – Layout .......................................................................................................................................... 23

Page 4: Evaluation Note EVAL-ADV7630EBZ Rev. B · Eval Note Rev. A Page 5 of 30 1. Introduction This evaluation note is intended to provide application support for the ADV7630 evaluation

Eval Note

Rev. A Page 4 of 30

7. Appendix 3 – Flash Magic .................................................................................................................................. 26

8. Appendix 4 – Downloading from FTP ................................................................................................................ 27

9. Appendix 5 – Software Driver Controls ............................................................................................................. 28

Page 5: Evaluation Note EVAL-ADV7630EBZ Rev. B · Eval Note Rev. A Page 5 of 30 1. Introduction This evaluation note is intended to provide application support for the ADV7630 evaluation

Eval Note

Rev. A Page 5 of 30

1. Introduction This evaluation note is intended to provide application support for the ADV7630 evaluation board. It also provides details on the set up and manual configuration of the evaluation board. Software drivers are available for this evaluation board - a separate user guide is available for these software drivers. This note applies to board revisions B.

2. Evaluation Kit The ADV7630 evaluation board kit should consist of the following:

1. ADV7630 Evaluation Board

2. 7.5V DC power supply module

3. USB cable

3. Initial Hardware Configuration The ADV7630 evaluation board is a standalone evaluation platform used to demonstrate all features of the ADV7630. To assemble the platform, connect the female connector of the 7.5V DC power supply module supplied with the evaluation kit to the motherboard power connector, J10. To turn the evaluation platform on, flick the power switch (S1) to position “ON”. The green power LED (D15) should light. Once the board is powered up, connect the USB cable supplied with the evaluation kit to USB connector, J12. The hardware platform is ready to use. In order to use it DVP Eval software must be installed as per section 3.1

Figure 1. Evaluation board

Page 6: Evaluation Note EVAL-ADV7630EBZ Rev. B · Eval Note Rev. A Page 5 of 30 1. Introduction This evaluation note is intended to provide application support for the ADV7630 evaluation

Eval Note

Rev. A Page 6 of 30

3.1 DVP Eval Installation

1. DVP Eval software can be downloaded from FTP site. Refer to Appendix 4 – Downloading from FTP section.

2. Run ADI-DVP-Installer-1.5.3.exe file

3. Review the license agreement and click “I Agree” if the terms of the agreement are acceptable

Figure 2 – License Agreement

4. Select the desired access links – desktop shortcut and/or start menu shortcut (see Figure 3)

Figure 3 - Installation Options

5. Press “Next>”

6. Accept installation folder (see Figure 4; the default folder is User’s “My documentation” folder) and press install.

Page 7: Evaluation Note EVAL-ADV7630EBZ Rev. B · Eval Note Rev. A Page 5 of 30 1. Introduction This evaluation note is intended to provide application support for the ADV7630 evaluation

Eval Note

Rev. A Page 7 of 30

Figure 4 - Installation Folder

7. Depending on your PC configuration the following window may pop up. If so Select ‘This program installed correctly”

Figure 5.System window

8. Shortcuts to the program are placed in the start menu and on the Desktop (see Figure 6). Double-click on the icon to launch the software.

Page 8: Evaluation Note EVAL-ADV7630EBZ Rev. B · Eval Note Rev. A Page 5 of 30 1. Introduction This evaluation note is intended to provide application support for the ADV7630 evaluation

Eval Note

Rev. A Page 8 of 30

Figure 6. The desktop Icon

9. Initial screen on launching the DVP Eval Software is shown on Figure 7. At this stage it may be necessary to update your install with the Board Files for the evaluation platform you intend to work on.

Figure 7. Initial screen of DVP Eval Software

10. A Folder with the correct devices files must be placed in xml\New Boards Folder. Simply copy whole content of ADV7630 directory into New Boards.

Page 9: Evaluation Note EVAL-ADV7630EBZ Rev. B · Eval Note Rev. A Page 5 of 30 1. Introduction This evaluation note is intended to provide application support for the ADV7630 evaluation

Eval Note

Rev. A Page 9 of 30

Figure 8. New boards folder – example

11. Within the DVP Eval Menu select : File-> Update Devices.

Figure 9. Updating boards (1)

12. A pop up window notifies the user that the update was successful.

Figure 10. Updating boards (2)

13. The Folder with the device files is moved into a subfolder within New Boards called ‘Recent Boards Added.’

Page 10: Evaluation Note EVAL-ADV7630EBZ Rev. B · Eval Note Rev. A Page 5 of 30 1. Introduction This evaluation note is intended to provide application support for the ADV7630 evaluation

Eval Note

Rev. A Page 10 of 30

3.2 Loading/Unloading Boards

3.2.1 Loading a Board The following steps must be performed to start a new DVP Eval session by loading a new board.

1. Click “Choose Board…”

2. Figure 11. Choose board button

3. From the Board Selector window, select your attached system e.g. “ADV7630” as RX, “None” for MotherBoard and “None” for TX.

4. Click “Load”

Note: If the board is standalone, select the board in whichever window it is populated under (i.e. RX, Motherboard, TX) and leave the other windows at “None”.

Page 11: Evaluation Note EVAL-ADV7630EBZ Rev. B · Eval Note Rev. A Page 5 of 30 1. Introduction This evaluation note is intended to provide application support for the ADV7630 evaluation

Eval Note

Rev. A Page 11 of 30

Figure 12 - Board Selection

3.2.2 Unloading a Board The following steps must be performed to end an DVP Eval session by unloading the selected board.

1. Select Files -> Unload Boards

Page 12: Evaluation Note EVAL-ADV7630EBZ Rev. B · Eval Note Rev. A Page 5 of 30 1. Introduction This evaluation note is intended to provide application support for the ADV7630 evaluation

Eval Note

Rev. A Page 12 of 30

3.3 Running Scripts Scripts can be run by either of the following options:

1. Select Scripts -> Project Name e.g. ADV7630

2. Follow the script tree as outlined in the expanding menus (see Figure 13)

3. Select Scripts -> Run Script

4. Open the script folder of the desired project

5. Select the desired script and click “Open”

Please be patient as the script may take several seconds to run. Successful download of the script is notified by the green light at the bottom of the screen flashing twice.

Figure 13 – DVP Eval Script Tree

Page 13: Evaluation Note EVAL-ADV7630EBZ Rev. B · Eval Note Rev. A Page 5 of 30 1. Introduction This evaluation note is intended to provide application support for the ADV7630 evaluation

Eval Note

Rev. A Page 13 of 30

3.4 Other DVP Eval Features

3.4.1 Register Control The following steps must be performed to use DVP Eval Register Control:

1. Select Tools -> Register Control

2. Enter the Device Address in HEX (see Figure 14)

3. Enter the desired register address in HEX

4. Press the “Write” button to write a value to the selected register

5. Press the “Read” button to read a value from the selected register

Figure 14 - Register Control Window

Page 14: Evaluation Note EVAL-ADV7630EBZ Rev. B · Eval Note Rev. A Page 5 of 30 1. Introduction This evaluation note is intended to provide application support for the ADV7630 evaluation

Eval Note

Rev. A Page 14 of 30

4. The ADV7630 Evaluation Platform in Depth

4.1 Hardware Overview The following features of the ADV7630 evaluation board should be noted

4.1.1 Connectors

1. 4 x HDMI inputs (J2, J3, J6, J8)

2. 2 x HDMI outputs (J5, J7)

3. 1 x UART connector (J11)

4. 1 x USB connector (J12)

5. 1 x Power Supply Connector (J10)

4.1.2 Jumpers Microcontroller

1. MUC boot ROM location (K2) – default position ‘B’

2. MUC reset (K1) – default position ‘not inserted’

3. Microcontroller reset control (K9) – default position ‘not inserted’

4. UART (K4) - default position ‘not inserted’

Power

5. DVDD-JP (must be inserted)

6. TX_AVDD-JP (must be inserted)

7. TXA_PVDD-JP (must be inserted)

8. TXA_PVDD-JP (must be inserted)

9. TXB_PVDD-JP (must be inserted)

10. TX_TVDD-JP (must be inserted)

11. SYS_3P3V-JP (must be inserted)

12. DVDDIO-JP (must be inserted)

Page 15: Evaluation Note EVAL-ADV7630EBZ Rev. B · Eval Note Rev. A Page 5 of 30 1. Introduction This evaluation note is intended to provide application support for the ADV7630 evaluation

Eval Note

Rev. A Page 15 of 30

4.1.3 Switches & Buttons

1. ON/OFF (S1)

2. Software enable/disable (S3)

3. DUT reset (S4)

4. MCU reset (S2)

4.1.4 Miscellaneous

1. 1x 20 way connectors (J9)

2. Software driver LEDS (LED1, LED2, LED3, LED4, LED5, LED6)

3. I2C header (P1)

Figure 15 - ADV7630 Evaluation Platform

RS-232

USB

POWER

SUPPLY

HDMI INPUTS

HDMI OUTPUT

ADV7630

LPC2387

Micrcontroller

Page 16: Evaluation Note EVAL-ADV7630EBZ Rev. B · Eval Note Rev. A Page 5 of 30 1. Introduction This evaluation note is intended to provide application support for the ADV7630 evaluation

Eval Note

Rev. A Page 16 of 30

4.2 Using the ADV7630 Evaluation Platform

4.2.1 Connecting an Input Video Source To connect an input video source to the ADV7630 evaluation board, use a HDMI cable and the input HDMI connector to J2, J3, J6 or J8. Do not use excessive force when connecting or disconnecting the cable as this may result in damage to the evaluation board.

4.2.2 Connecting to a Video Sink To connect the ADV7630 evaluation board to a video sink, use a HDMI cable and the output HDMI connector to J5 or J7. Do not use excessive force when connecting or disconnecting the cable as this may result in damage to the evaluation board.

4.2.3 Updating the Software Driver To download updated software driver code to the microcontroller used on the ADV7630 evaluation board, please perform the following steps

1. Power off the board

2. Insert jumper K4

3. Ensure jumper K2 is in position A

4. Ensure that jumper K1 (MCU RESET) is not inserted

5. Connect a serial cable between the computer to be used for the download and the UART connector (J11), on the ADV7630 evaluation board

6. Power on the board by moving the ON/OFF switch (S1) to position ON.

7. Start the Flashmagic download by pressing “Start”. For information on where to obtain and how to use the Flashmagic tool, please see Appendix 3 – Flash Magic.

8. When the download has completed, power off the board by moving the ON/OFF switch (S1) to position OFF.

9. Remove jumper K4.

10. Ensure jumper K2 is in position B.

11. Power on the board by moving the ON/OFF switch (S1) to position ON.

If the Flash magic tool gives a warning, please check the setup and jumper positions carefully.

Page 17: Evaluation Note EVAL-ADV7630EBZ Rev. B · Eval Note Rev. A Page 5 of 30 1. Introduction This evaluation note is intended to provide application support for the ADV7630 evaluation

Eval Note

Rev. A Page 17 of 30

4.2.4 Interfacing with the Software Driver Jumper K1, when inserted, pulls the microcontroller reset low. To use the software driver, please ensure that K1 is removed.

To stop and start the software driver (e.g. to allow access to the I2C over DVP Eval), toggle the SW_ENABLE (S3) switch on the evaluation board. When disabled, the driver will send the message “REP: Driver Disabled”. When enabled, the driver will send the message “REP: Driver Enabled” and any status updates will be displayed.

Please see the software driver documentation for the functions performed by software driver LEDS (LED1, LED2, LED3, LED4, LED5, LED6). To enable the software driver, switch the software enable switch (S3) to SW_ENABLE. To disable the software driver, switch the software enable switch (S3) away from SW_ENABLE.

For information on the latest software driver, please contact your local FAE or sales office.

Page 18: Evaluation Note EVAL-ADV7630EBZ Rev. B · Eval Note Rev. A Page 5 of 30 1. Introduction This evaluation note is intended to provide application support for the ADV7630 evaluation

Eval Note

Rev. A Page 18 of 30

Appendix 1 – Schematics

Figure 8. T ransciever schematics

Page 19: Evaluation Note EVAL-ADV7630EBZ Rev. B · Eval Note Rev. A Page 5 of 30 1. Introduction This evaluation note is intended to provide application support for the ADV7630 evaluation

Eval Note

Rev. A Page 19 of 30

Figure 9. ARM7 schematics

Page 20: Evaluation Note EVAL-ADV7630EBZ Rev. B · Eval Note Rev. A Page 5 of 30 1. Introduction This evaluation note is intended to provide application support for the ADV7630 evaluation

Eval Note

Rev. A Page 20 of 30

Figure 10. HDMI-IN/HDMI-OUT schematics

Page 21: Evaluation Note EVAL-ADV7630EBZ Rev. B · Eval Note Rev. A Page 5 of 30 1. Introduction This evaluation note is intended to provide application support for the ADV7630 evaluation

Eval Note

Rev. A Page 21 of 30

Figure 11. USB Circuitry schematics

Page 22: Evaluation Note EVAL-ADV7630EBZ Rev. B · Eval Note Rev. A Page 5 of 30 1. Introduction This evaluation note is intended to provide application support for the ADV7630 evaluation

Eval Note

Rev. A Page 22 of 30

Figure 12. Power supply schematics

Page 23: Evaluation Note EVAL-ADV7630EBZ Rev. B · Eval Note Rev. A Page 5 of 30 1. Introduction This evaluation note is intended to provide application support for the ADV7630 evaluation

Eval Note

Rev. A Page 23 of 30

Appendix 2 – Layout

Figure 16: Layout Silkscreen (Top)

Figure 17: Layout Layer 1 (Top)

Page 24: Evaluation Note EVAL-ADV7630EBZ Rev. B · Eval Note Rev. A Page 5 of 30 1. Introduction This evaluation note is intended to provide application support for the ADV7630 evaluation

Eval Note

Rev. A Page 24 of 30

Figure 18: Layout Layer 2 (GND)

Figure 19: Layout Layer 3 (PWR)

Page 25: Evaluation Note EVAL-ADV7630EBZ Rev. B · Eval Note Rev. A Page 5 of 30 1. Introduction This evaluation note is intended to provide application support for the ADV7630 evaluation

Eval Note

Rev. A Page 25 of 30

Figure 20: Layout Layer 4 (Bottom)

Figure 21: Layout Silkscreen (Bottom)

Page 26: Evaluation Note EVAL-ADV7630EBZ Rev. B · Eval Note Rev. A Page 5 of 30 1. Introduction This evaluation note is intended to provide application support for the ADV7630 evaluation

Eval Note

Rev. A Page 26 of 30

Appendix 3 – Flash Magic

Software Setup: the Flashmagic tool can be downloaded from www.flashmagictool.com. Analog Devices does not take responsibility for the content of any external sites.

Note: Please ensure the tool settings are configured to “Use DTR and RTS to control RST and ISP pin”. The tool settings are accessed by navigating through Options -> Advanced Options -> Hardware Config.

All other main settings should be as follows:

- Device: LPC2468

- COM: As per user device

- Baud rate: 115200

- Interface: None (ISP)

- Oscillator: 14746

- Ensure “Verify after programming” is enabled

- Ensure “Erase blocks used by Hex File” is enabled

- Specify filename to download

http://www.flashmagictool.com/
Page 27: Evaluation Note EVAL-ADV7630EBZ Rev. B · Eval Note Rev. A Page 5 of 30 1. Introduction This evaluation note is intended to provide application support for the ADV7630 evaluation

Eval Note

Rev. A Page 27 of 30

Appendix 4 – Downloading from FTP

Using an FTP client (e.g. Filezilla – http://filezilla-project.org/download.php?type=client - Analog Devices does not take responsibility for the content of any external sites), please log on to download the latest evaluation software.

Host: ftp.analog.com

Username: e.g. ADV7630

Password: supplied from FAE/product line

Port: leave empty (FTP client will automatically populate this)

Figure 22 - Filezilla Settings

http://filezilla-project.org/download.php?type=client
ftp://ftp.analog.com/
Page 28: Evaluation Note EVAL-ADV7630EBZ Rev. B · Eval Note Rev. A Page 5 of 30 1. Introduction This evaluation note is intended to provide application support for the ADV7630 evaluation

Eval Note

Rev. A Page 28 of 30

Appendix 5 – Software Driver Controls

When using the software driver, please connect a UART terminal e.g. Hyperterminal or TeraTerm for feedback on the status of the software driver.

Figure 23. Software driver feedback

Please use the following commands to interface with the software driver

? Print help

help Print help

amute Mute audio output <on or off>

arctx ARC TX mode <on or off>

avmute Send AVMUTE <on or off>

cec CEC support <on or off>

dbg Select debug output [rx] [tx] [hdcp] [edid] [cec] [int] [none] [all]

dbg+ Same as dbg command with output addition

Page 29: Evaluation Note EVAL-ADV7630EBZ Rev. B · Eval Note Rev. A Page 5 of 30 1. Introduction This evaluation note is intended to provide application support for the ADV7630 evaluation

Eval Note

Rev. A Page 29 of 30

dbg- Same as dbg command with output removal

enc Output encryption <on, off or us(same as upstream)>

fs Fast switching <on or off>

i2cr i2c read <device> <register> <byte count>

i2cw i2c write <device> <register> <value>

i2cand i2c AND register with value <device> <register> <value>

i2cor i2c OR register with value <device> <register> <value>

i2cxor i2c XOR register with value <device> <register> <value>

i2cdbg i2c debug <device addr, dev addr, ...>

memr Read memory <address(32-bit aligned)> <byte count>

memw Write memory <address(32-bit aligned)> <value>

mode Set operating mode <rec, rep, xmt or auto>

mute Set mute mode <man or auto>

mtime Set mute times in ms <For TMDS, For Blackout>

out Set TX output <hdmi, dvi, us or forced>

port Select input port <a, b, c, d, e, f, g n(none) or t(auto)>

reset Reset system

run Resume software

stat Print system status

stop Stop software

vmute Video output mute <on or off>

edidmod Update RX EDID <on or off>

EDID will be modified before being written to the RX internal EDID.

Refer to REP_EVENT_TX_EDID_READY event processing in rep_notify.c

power Power <on or off>, <mode 0 or 1>

cecaudio send cec message about audio <opcode>, <directly addressed >,

<parameters>

xmtmode When no HDMI input connected (MXT mode), keep HDMI TX on or off

<on or off>

Page 30: Evaluation Note EVAL-ADV7630EBZ Rev. B · Eval Note Rev. A Page 5 of 30 1. Introduction This evaluation note is intended to provide application support for the ADV7630 evaluation

Eval Note

Rev. A Page 30 of 30

UART Terminal Settings

- Baud rate: 115200

- Data: 8-bit

- Parity: none

- Stop: 1-bit

- Flow control: none


STM3240G-EVAL evaluation boardcourses.engr.uky.edu/.../stm3240g_eval_user_manual.pdf · STM3240G-EVAL evaluation board Introduction The STM3240G-EVAL evaluation board is a complete

STM3220G-EVAL evaluation board - STMicroelectronics€¦ · November 2016 DocID018499 Rev 6 1/68 1 UM1057 User manual STM3220G-EVAL evaluation board Introduction The STM3220G-EVAL

TMC6200-EVAL Evaluation Kit - Trinamic · TMC6200-EVAL Evaluation Kit • Document Revision V1.00 • 2019-July-18 5 / 6 6.There are 2 solder options available on the TMC6200-EVAL

Data brief - EVAL-RHRICL1ALV1 - EVAL-RHRICL1ALV1 ...€¦ · EVAL-RHRICL1ALV1 evaluation board - latched EVAL-RHRICL1ALV1 Data brief DB3985 - Rev 1 - July 2019 For further information

Eval-FB2M5LRR Ethernet LC Evaluation Kit User Guide · 2020-03-30 · Eval-FB2M5LRR Ethernet LC Evaluation Kit User Guide Eval-FB2M5LRR Revision A 2 EVALUATION KIT CONTENTS The Evaluation

Data brief - STM32H743I-EVAL STM32H753I-EVAL - Evaluation ... · STM32H743I-EVAL STM32H753I-EVAL Description DB3235 - Rev 3 page 2/6. 2 Ordering information To order STM32H743I-EVAL

Hardware Version V1.5 TMC5130-EVAL EVALUATION BOARD …

EVAL-AD7176-2SDZ User Guide - Analog Devices · 2. Connect the EVAL -SDP-CB1Z evaluation board to the EVAL-AD7176-2SDZ evaluation board as shown in Figure 2. 3. Screw the two evaluation

Data brief - STM32H743I-EVAL STM32H753I-EVAL - Evaluation ... · Data brief - STM32H743I-EVAL STM32H753I-EVAL - Evaluation boards with STM32H743XI and STM32H753XI MCUs Author: STMICROELECTRONICS

Evaluation Board for ADG790 EVAL-ADG790...Evaluation Board for ADG790 EVAL-ADG790 Rev. 0 Evaluation boards are only intended for device evaluation and not for production purposes

EVAL-AD7265/AD7266 Evaluation Board for the AD7265/AD7266 ... · Evaluation Board for the AD7265/AD7266 EVAL-AD7265/AD7266 Rev. 0 Evaluation boards are only intended for device evaluation

Climate-Eval - Earth-Eval...Eval Community of Practice. 1.1 Evaluation purposes in climate mitigation Evaluation purposes are listed in every evaluation textbook. Firstly, an evaluation

EVAL-RHF1201V2 evaluation board · EVAL-RHF1201V2 Evaluation board description Doc ID 024032 Rev 1 9/14 5 Evaluation board description Figure 9 shows the components on the evaluation

STM3240G-EVAL evaluation board - st.com · October 2016 DocID022138 Rev 5 1/67 1 UM1461 User manual STM3240G-EVAL evaluation board Introduction The STM3240G-EVAL evaluation board

STM3220G-EVAL evaluation board - RS Components · STM3220G-EVAL evaluation board Introduction The STM3220G-EVAL evaluation board is a complete demonstration and development platform

EVAL-ADP1621 Evaluation Board for Constant-Frequency

EVAL 6474 evaluation module

STM3210C-EVAL evaluation board

EVAL-ADT7516EBZ Evaluation Board User Guide

Evaluation board with STM32G4xxQE MCU · Data brief - STM32G474E-EVAL STM32G484E-EVAL - Evaluation board with STM32G4xxQE MCU Author: STMICROELECTRONICS Subject: The STM32G4x4E-EVAL

Gigadevice GD32 Cortex-M3 Evaluation Boards & Starter Kits Cortex-M3 Eval... · GD32103B-EVAL Part Number Board Features GD32103C-EVAL GD32103E-EVAL GD32105C-EVAL GD32107C-EVAL GD32150R-EVAL

EVAL-SSM2604 Evaluation Board for Audio Codec … · Evaluation Board for Audio Codec EVAL-SSM2604 Rev. 0 Evaluation boards are only intended for device evaluation and not for production

ADAU1761 Evaluation Board EVAL-ADAU1761Z - … · ADAU1761 Evaluation Board EVAL-ADAU1761Z ... AUDIO OUTPUTS 08055-001 Figure 1. EVAL-ADAU1761Z ... Check the box for

EVAL-ADP1046A User Guide · graphical user interface (GUI) EVALUATION KIT CONTENTS EVAL-ADP1046A resonant mode evaluation board ADDITIONAL EQUIPMENT NEEDED

AD8333-EVAL Evaluation Board for the AD8333 I/Q ... · AD8333-EVAL Rev. 0 | Page 3 of 12 INTRODUCTION The AD8333-EVAL evaluation board provides a platform for test and evaluation

EVAL-SSM2604 Evaluation Board for Audio Codec Data Sheet ... · EVAL-SSM2604 Rev. 0 Evaluation boards are only intended for device evaluation and not for production purposes. Evaluation

STM3210B-EVAL evaluation board - STMicroelectronics · evaluation board Introduction The STM3210B-EVAL is an evaluation board for STMicroelectronic’s ARM TM Cortex-M3 core-based

STM3210C-EVAL evaluation board · STM3210C-EVAL evaluation board Introduction The STM32F107VCT evaluation board STM3210C-EVAL is designed as a complete development platform for STMicroelectronic's

Data brief - EVAL-TDA7803A - EVAL-TDA7803A evaluation board

TMC2160-EVAL Evaluation Kit - Trinamic€¦ · TMC2160-EVAL Evaluation Kit • Document Revision V1.02 • 2020-FEB-27 5 / 8 6. Figure 3: Pin Headers on the TMC2160-EVAL 2 Hardware

EVAL 6000: Foundations of Evaluation Final lecture!

Patterns for Visualization Evaluation - UMIACSelm/projects/eval-patterns/eval...Keywords: visualization, evaluation, validation, patterns, best practices, pattern language. 1 Introduction

EVAL-AD7091R-2SDZ/AD7091R-4SDZ/ AD7091R-8SDZ User Guide … · EVALUATION BOARD DESCRIPTION The . EVAL-AD7091R-2SDZ, EVAL-AD7091R-4SDZ, and EVAL-AD7091R-8SDZ are full featured evaluation

ADAU1701 Mini Evaluation Board EVAL-ADAU1701MINIZ€¦ · ADAU1701 Mini Evaluation Board EVAL-ADAU1701MINIZ Rev. 0 Evaluation boards are only intended for device evaluation and not

ADD8754-EVAL Evaluation Kit for LCD Power, … · Evaluation Kit for LCD Power, VCOM, and Gate Modulation ADD8754-EVAL Rev. A Evaluation boards are only intended for device evaluation