exsulation l5000 dsc5002 lamella non combustible eifs · wrap dryvit detail mesh wrapped to...

The architecture, engineering and design of the project using the Dryvit products is theresponsibility of the project's design professional. All systems must comply with localbuilding codes and standards. This detail is for general information and guidance onlyand Dryvit Systems Canada specifically disclaims any liability for the use of this detailand/or for the architecture, design, engineering or workmanship of any project. Thedesign professional determines, at its sole discretion, whether this detail or a functionallyequivalent alternative is best suitedfor the project. Use of a functionally equivalent detaildoes not violate Dryvit's warranty. This detail is subject to change without notice.Contact Dryvit Systems Canada to ensure you have the most recent version.

EXSULATION® L5000Lamella Non Combustible EIFS

DSC5002

Exsulation L5000System Installation Details

129 Ringwood Drive PO Box 1268Stouffville, Ontario L4A 8A2800-263-3308www.dryvit.com

®

DRYVIT SYSTEMS CANADA

Exsulation® L5000 Table of Contents


NOTEDRYVIT MAKES NOREPRESENTATION REGARDINGCONFORMITY OF ITSSUGGESTIONS TO APPLICABLEBUILDING CODES, ENGINEERINGCRITERIA, SPECIFICAPPLICATIONS OR PROJECTLOCATIONS. ALL COMPONENTSINDICATED IN ILLUSTRATIONS, ASWELL AS OTHERS THAT MAY BEREQUIRED FOR THE INTEGRITYOF THE SYSTEM SHALL BEDESIGNED, DETAILED ANDENGINEERED BYREPRESENTATIVES OF THEARCHITECT, OWNER ORCONTRACTOR TO BE INCONFORMANCE WITH MODELCODES, ARCHITECTURAL ANDENGINEERING REQUIREMENTSPERTAINING TO SPECIFICBUILDING PROJECTS.

DRYVIT MAKES NO WARRANTY,EXPRESSED OR IMPLIED, AS TOTHE ARCHITECTURAL DESIGN,ENGINEERING, OR WORKMANSHIPOF PROJECTS UTILIZING DRYVITSYSTEMS OR PRODUCTS.

THE LIABILITIES OF DRYVIT SHALLBE AS STATED IN THEEXSULATION L5000 LIMITEDCOMMERCIAL WARRANTY.CONTACT DRYVIT FOR A FULLAND COMPLETE COPY OF THEWARRANTY.

DETAIL

EXL.0.0.01 NORMAL AND HIGH IMPACT

EXL.0.0.02 LAMELLA SLAB LAYOUT

EXL.0.0.03 FOUNDATION WITH DRAINAGE STRIP - EXTENDED 2D VIEW

EXL.0.0.04 HEAD/SILL

EXL.0.0.05 HEAD/SILL FOR SELF FLASHING WINDOW OPTIONS

EXL.0.0.06 PROTECTION OF ROUGH OPENINGS

EXL.0.0.07 ROUGH OPENING AND SILL PREPARATION - AQUAFLASH ® SYSTEM

EXL.0.0.08 JAMB

EXL.0.0.09 PARAPET - CAP FLASHING

EXL.0.0.10 PARAPET/ WALL TERMINATION

EXL.0.0.11 PARAPET - SOLID SUBSTRATE

EXL.0.0.12 SOFFIT/FASCIA INTERSECTION

EXL.0.0.13 SOFFIT - UNINSULATED

EXL.0.0.14 INSIDE/OUTSIDE CORNERS

EXL.0.0.15 OUTSIDE CORNER - HIGH IMPACT

EXL.0.0.16A FLOORLINE DETAIL - APPLICATION SEQUENCE

EXL.0.0.16B HORIZONTAL SLIP JOINT - EXTENDED 2D VIEW

EXL.0.0.17 HORIZONTAL SLIP JOINT

EXL.0.0.18 TWO-STAGE JOINT - EXTENDED 2D VIEW

EXL.0.0.19 STRUCTURAL EXPANSION JOINTS

EXL.0.0.20 PENETRATIONS

EXL.0.0.21 WALL PENETRATIONS

EXL.0.0.22 SIGN ATTACHMENT

EXL.0.0.23 AESTHETIC REVEALS

EXL.0.0.24 HORIZONTAL JOINT AT STONE VENEER

EXL.0.0.25 SOFFIT VENT


®


Exsulation® L5000 EXL.0.0.01

Normal and High Impact

Notes:

1. Dryvit recommends thatground floor applicationsand all facades exposedto abnormal stress, hightraffic, or deliberateimpact have the basecoat reinforced withPanzer® 15 or 20 Meshprior to Standard PlusMesh. Location of highimpact zones should beindicated in contractdrawings.



®


NORMAL IMPACT

HIGH IMPACT

Primus® DM Adhesive ribbons

Dryvit Secondary Barrier

Approved mechanical fastener

Lamella (6" strips)

Primus DM Basecoat

Dryvit reinforcing mesh

Primus DM Basecoat

Dryvit finish

Backwrap

Dryvit Secondary Barrier

Approved mechanical fastener

Lamella (6" strips)

Primus DM Basecoat


Primus DM Basecoat

Dryvit finish

Backwrap

Primus DM Basecoat


Substrate

Primus DM Adhesive ribbons

Substrate

152.

4mm

(6")

152.

4mm

(6")

R-002-07-08

EXL.0.0.02

Lamella Slab Layout



®


Notes:

1. Fasteners required inconjunction with adhesiveon first row and everyfourth row thereafter asshown.

2. Standard PB fastener andwasher required.

Exsulation® L5000

Approvedmechanicalfastener andplate

Substrate

Ensure thatfibre orientationis perpendicularto the substrate

90°

Substrate

Fibre

R-002-07-08


Foundation with Drainage Strip - Extended 2d View



®


610

mm

(2'-0

") m

ax. (

see

note

2)

200m

m (8

") m

in.

Dryvit water-resistivebarrier coating

Dryvit adhesive in verticalnotched trowel configuration

applied to lamella

Slope grade away fromfoundation wall

Dryvit basecoat


Dryvit finish

Dryvit Backstop™ NT overGrid Tape

Dryvit Drainage Strip adhered withdabs of AP Adhesive (see note 3)

Dryvit Detail Mesh™ wrappedto backside of lamella min.63.5 mm (2 12")

Dryvit Aquaflash® applied overDryvit water-resistive barriercoating at foundation (see note 2)

Notes:

1. Dryvit recommends thatground floor applicationsand all facades exposed toabnormal stress, hightraffic, or deliberate impacthave the base coatreinforced with Panzer® 15or 20 Mesh prior toStandard Plus Mesh.Location of high impactzones should be indicatedin contract drawings.

2. Expansion joint is requiredalong top of foundation if610mm (2'-0") dimension isexceeded.

3. Ensure bottom edge ofDrainage Strip is left free todrain.

4. Notched trowel sizeminimum of 12" x 12", bymaximum 2" on centre.

5. Adhesive applied to thelamellas.

Lamella

Sheathing

R-002-07-08


Head/Sill

Sill Pan Flashing Detail



®


Notes:1. Dryvit recommends that ground floor applications

and all facades exposed to abnormal stress, hightraffic, or deliberate impact have the base coatreinforced with Panzer® 15 or 20 mesh prior toStandard Plus mesh. Location of high impactzones should be indicated on contract drawings.

DRYVITEXSULATIONL5000 SYSTEM

BY OTHERS

Approved substrate

Dryvit water-resistive barrier coating

Dryvit adhesive in vertical notched trowelconfiguration applied to lamella

Lamella insulation notched to accommodateDrainage Strip, flashing, and AquaFlash® System

Wrap Dryvit Detail Mesh wrapped tobackside of lamella min. 63.5 mm (2 12")

Dryvit Demandit™ or ColorPrime™ on surface(s) to receivesealantDryvit compatible sealant with closed cell backer-rodand weep tubes every 600 mm (24"), by others

19 mm (3/4") min.

Continuous flashing, by others

Fillet caulk with bond breaker, by others

Dryvit AquaFlash System

Wrap Dryvit Detail Mesh™ wrapped tobackside of lamella min. 63.5 mm (2 12")

Continuous pan flashing with end dams, byothers, see detail below

Dryvit compatible sealant, by others

Dryvit Drainage Stripset in dabs of AP Adhesive

See Protection of RoughOpening as per EXS.0.0.06

and EXS.0.0.07

Provide air seal,by others, aroundinterior of window

per windowmanufacturer's

requirements

38mm(1-1/2") min.

Dryvit reinforcing mesh embedded in base coatDryvit finish

R-002-07-08


Head/Sill for Self Flashing Window Options

Notes:1. Dryvit recommends that ground floor

applications and all facades exposed toabnormal stress, high traffic, or deliberateimpact have the base coat reinforced withPanzer® 15 or 20 mesh prior to Standard Plusmesh. Location of high impact zones should beindicated on contract drawings.

2. Additional head flashing may be necessary forwindows that are not self flashing. Drainable Sill Option

Approved substrateDryvit water-resistive barrier coatingDryvit adhesive in vertical notched trowelconfiguration applied to lamellaLamella insulation notched to accommodateDrainage Strip, flashing, and AquaFlash®

Dryvit Demandit™ or Color Prime™ onsurface(s) to receive sealant

Dryvit compatible sealant with closed cell backer-rodand weep tubes every 600 mm (24"), by others

19 mm (3/4") min.

Window integral flashing

Dryvit compatible sealant, by others

Dryvit Demandit or Color Prime onsurface(s) to receive sealant

Wrap Dryvit Detail Mesh 63.5 mm (2 12")min. at backside of lamella

Dryvit Drainage Strip set indabs of AP Adhesive

Dryvit AquaFlash meshembedded in Dryvit AquaFlash

Liquid lapped over window flange

19 mm (3/4") min.

Provide air seal, by others,around interior of window

per window manufacturer'srequirements

Wrap Dryvit Detail Mesh™ 63.5 mm (21

2") min. at backside of lamella


DRYVIT EXSULATIONL5000 SYSTEM

BY OTHERS

Sill pan flashing, by others


Dryvit AquaFlash

Transition flashing



®


Dryvit reinforcing mesh embedded in base coatDryvit finish

See Protection of Rough Openingas per EXS.0.0.06 and EXS.0.0.07

R-002-07-08


Protection of Rough Openings



®


Application Sequenceand Notes:

1. Apply WRB over sheathingand into rough opening.

2. Embed Detail Mesh™ intoWRB, stopping at sill.Embed diagonal mesh asshown at all corners.

3. Once embedment iscomplete, apply WRB overremainder of the substrateas illustrated.

4. Apply AquaFlash® andAquaFlash mesh as perDSC196 - Sills only if WRBis applied around thebalance of the roughopening.

AquaFlash is applied using abrush or deep-nap roller. EmbedAquaFlash Mesh into wetAquaFlash and allow to set.

Apply second coat fully coveringthe AquaFlash Mesh.

Alternatively, Dryvit's Flashing tape or EIFS tape maybe used and is applied aroundthe entire rough opening, but notreturning to the header. Seeillustration below.

* Water-resistive barrier to beapplied over EIFS tape with apositive lap of 2" minimum.

2

63.5mm(2 12") min.

63.5mm (2 1 2") min.

Substrate andsheathing assembly

3Dryvit

AquaFlashSystem

4

1

EIFS Tape Application

Apply 1st

2nd3rd

4th*(See Note)

R-002-07-08


Rough Opening and Sill Preparation - AquaFlash System



®


Notes:

1. The AquaFlash System is acombination of AquaFlashLiquid used in conjunction withAquaFlash Mesh to sealsubstrates around windows,doors and other openings.

2. Install AquaFlash System(including diagonal "butterflies")onto sill and allow to dry.

3. Alternatively, Dryvit FlashingTape or EIFS tape may beused.

Step #1 Step #2

Step #4

Install AquaFlash®System at sill (seenote 2)

Step #3

Step #5

Install DryvitAquaFlash Meshembedded inAquaFlash at headand over upturnedpan flanges

63.5mmmin.

Install sill panflashing

Install DryvitAquaFlash Meshembedded inDryvit water-resistivebarrier coating atjambs.

Installflashingsat head

Refer to EXS.0.0.08for jamb detail

Apply AquaFlashMesh and

AquaFlash overFlashing

R-002-07-08


Jamb



®


DRYVITEXSULATION

L5000 SYSTEM


Dryvit Grid Tape inDryvit water-resistivebarrier coating

Continuous Dryvitcompatible sealant andclosed cell backer-rod,by others

Dryvit Demandit™ orColor Prime™ on surfacesto receive sealant

Dryvit adhesive invertical notched trowelconfiguration applied atbackside of lamella

Wrap Dryvit Detail Mesh™63.5 mm (2 12") min. atbackside of lamella

Dryvit reinforcing meshembedded in base coat

19 mm(3/4") min.

BY OTHERS

Notes:

1. Dryvit recommends thatground floor applicationsand all facades exposed toabnormal stress, hightraffic, or deliberate impacthave the base coatreinforced with Panzer®15or 20 mesh prior toStandard Plus mesh.Location of high impactzones should be indicatedon contract drawings.

Lamella

Dryvit finish

ApprovedSubstrate

Air Seal

R-002-07-08



Parapet - Cap Flashing


®


BY OTHERS

Roofassembly

Metal cap flashing, by others

Dryvit AquaFlash® system

Dryvit compatible sealantwith bond breaker, by others(see note 2)


63.5 mm (2-1/2") min.


Approved substrate


Dryvit adhesive in verticalnotched trowel configurationapplied to lamella

Lamella


Dryvit finish

Framing

Notes:

1. Dryvit recommends thatground floor applicationsand all facades exposedto abnormal stress, hightraffic, or deliberateimpact have the basecoat reinforced withPanzer® 15 or 20 meshprior to Standard Plusmesh. Location of highimpact zones should beindicated on contractdrawings.

2. Ensure parapet capping iswater tight if sealant is tobe applied here. Otherwiseextend capping overlap asrequired to avoid moisturemigration behind system.

Parapetcap sheet

R-002-07-08


EXL.0.0.10

Parapet/Wall Termination


®


Exsulation® L5000

Parapet/Wall Termination

Notes:1. Dryvit recommends that ground floor applications and all façades exposed to abnormal stress, high traffic, or deliberate

impact have the base coat reinforced with Panzer ® 15 or 20 mesh prior to Standard Plus mesh. Location of high impactzones should be indicated on contract drawings.

2. Lap all flashing and water-resistant barriers in shingle fashion.3. Use Dryvit AquaFlash System at wall/sleeve transition.

Roofing System

Aluminium reglet

Dryvit Exsulation L5000 System

Metal copingflashing

at parapet wall

Flashing sleeveshown in exploded

view

Lamella

Dryvit AquaFlash® System

Dryvit Drainage Strip

Dryvit compatible sealant w/ closedcell backer rod and weep tubesevery 600 mm (24") by others.

Roof flashing and counterflashing, by others

4" (102mm)

6" (153mm)

6" (153mm)

4"(102mm)

R-002-07-08



Parapet - Solid Substrate


®


Notes:

1. Dryvit recommends thatground floor applicationsand all facades exposed toabnormal stress, hightraffic, or deliberate impacthave the base coatreinforced with Panzer® 15or 20 mesh prior toStandard Plus mesh.Location of high impactzones should be indicatedon contract drawings.

2. If system on back ofparapet exceeds 610mm(2'-0") in height, provisionsfor drainage are requiredalong wall base.

3. Ensure parapet capping iswater tight if sealant is tobe applied here. Otherwiseextend capping overlap asrequired to avoid moisturemigration behind system.

4. Install mechanical fixingsas per EXL.0.0.02.

BY OTHERS

Metal cap flashing(by others)

Wrap Dryvit Detail Mesh 63.5mm (2 12") min. at backside

of lamella

Dryvit compatiblesealant (by others)

Roof flashing andcounter flashing, by

others

Approved substrate

Roof assembly

200

mm

(8")

min

.


Dryvit AquaFlash® Mesh embeddedin AquaFlash Liquid as water-resistivebarrier coating




Dryvit compatiblesealant, by others(see note 3)

Lamella


Dryvit finish

63.5 mm (2-1/2") min.

Approved mechanicalfastener

Parapetcap sheet

R-002-07-08


Soffit/Fascia Intersection

19 mm (3/4") min.

DRYVIT EXSULATIONL5000 SYSTEMBY OTHERS

Approved substrate


Dryvit adhesive invertical notched trowelconfiguration applied tolamella

LamellaDryvit reinforcing meshembedded in base coat

Dryvit finish

Dryvit reinforcing meshembedded in Dryvitwater-resistive barriercoating

Dryvit Drainage Strip

Wrap Dryvit Detail Mesh™63.5 mm (2 12") min. atbackside of lamella. Do notblock Drainage Strip withbase coat.


Notes:


2. Bottom edge of DryvitDrainage Strip shall bemasked during installationto prevent clogging ofdrainage channels.


®


Approved mechanical fixing

R-002-07-08


Soffit - Uninsulated



®


Notes:


2. Soffits without insulationrequire expansion jointsevery 6 m (20 ft).

3. Refer to Dryvit publicationDSC173 for specificrequirements for soffitareas.

4. Bottom edge of DryvitDrainage Strip shall bemasked during installationto prevent clogging ofdrainage channels.

Approved substrate

Dryvit water-resistivebarrier coatingDryvit adhesive in verticalnotched trowel configurationapplied to lamellaLamella

Dryvit reinforcing meshembedded in base coatDryvit finish

Wrap Dryvit Detail Mesh™63.5mm (2 12") min. atbackside of lamellaDryvit Drainage Strip™

25 mm (1") max.


DRYVIT EXSULATIONL5000 SYSTEMBY OTHERS

Dryvit Detail Mesh embedded inDryvit water-resistive barrier coating


R-002-07-08


Inside/Outside Corners



®


Approved substrate


Dryvit adhesive invertical notched trowelconfigurationLamella

Reinforcing meshembedded in base coat

Dryvit finish

200mm (8") min.(see notes 2 and 3)

200mm (8") min.(see notes 2 and 3)

Must overlap 200 mm(8") min. See above andnotes 2 and 3

Approved substrate


Lamella


Dryvit adhesive invertical notched trowelconfiguration


BY OTHERS

Dryvit reinforcingmesh embedded in


Dryvit reinforcing meshembedded in Dryvitwater-resistive barriercoating

Notes:


2. Double wrap outsidecorners with reinforcingmesh or use CornerMesh™.

3. Do not lap reinforcing meshwithin 200mm (8") of acorner.

R-002-07-08


Outside Corner - High Impact


Notes:


200 mm(8") min.


®


Approved substrate

Dryvit water-resistivebarrier coatingDryvit adhesive in verticalnotched trowel configurationapplied to lamellaDryvit reinforcing meshembedded in Dryvitwater-resistive barrier coatingLamella

Dryvit base coat

Dryvit Panzer®reinforcing mesh

Dryvit base coat

Dryvit corner mesh

Dryvit Standard or StandardPlus reinforcing meshoverlap min. 200 mm (8") atcorner

Dryvit base coat

Dryvit finish

Corner render profile (optional)

R-002-07-08

Exsulation® L5000 EXL.0.0.16A

Floorline Detail - Application Sequence



®


Notes:


Apply coat of Dryvitwater-resistive barrieronto substrate

2 Dryvit Aquaflash®System applied overDryvit water-resistivebarrier coating atfloorline joint

1

3 Apply Detail Mesh™at system terminationso to extend fullybehind insulation63.5 mm (2 12")

Dryvit base coat

Dryvit Mesh embeddedin base coat

Dryvit base coat

Lamella

Approved substrate

4Apply Dryvitadhesive to lamellain vertical notched

trowel configurationand allow to dry.

Closed-cellbacker-rod


R-002-07-08

Exsulation® L5000 EXL.0.0.16B

Horizontal Slip Joint - Extended 2d View



®


Notes:


2. Install fastener on first rowextending above slab. Usesupport/spacer block on firstrow until adhesive sets.

Approved substrate


Dryvit Detail Mesh™ prewrappedand embedded in base coat

Dryvit base coat

Dryvit adhesive in verticalnotched trowelconfiguration applied tolamella

Dryvit mesh embeddedin base coat

Dryvit base coat

Dryvit finish

Slope bottom surfacefor positive drainage

Dryvit AquaFlash System lapped onto lowersection and terminating at sealant bond line.

Dryvit Drainage Strip adheredin dabs of AP Adhesive


Closed cell backer-rod

Lamella insulation notchedto accomodate DrainageStrip and AquaFlash®System.


Temporary spacer block

R-002-07-08


Horizontal Slip Joint



®


Slip typeconnection

Approved substrate



Lamella

Dryvit reinforcing meshembedded in base coatDryvit Drainage Strip

Dryvit finish

Dryvit compatible sealant withclosed cell backer-rod, by others

Slope bottom surface forpositive drainage

19 mm(3/4") min.

Dryvit Demandit™ or ColorPrime™ on surfaces to receivesealantWrap Dryvit Detail Mesh™63.5 mm (2 12 ") min. atbackside of lamella

Notes:


2. Expansion joint in theExsulation L5000 System isnecessary where significantdifferential movement isexpected at floor lines.

3. Locate external sealant jointwithin 50 mm (2") of breakin sheathing.

4. Apply Dryvit AquaFlashSystem over prepared jointat change in substrate

Closed cellbacker-rod


BY OTHERS

Dryvit AquaFlash®System

Dryvit AquaFlash System appliedover top of previous coat and

extended towards bottom slopedsurface for drainage


R-002-07-08




®


Two-Stage Joint - Extended 2d

Notes:


Sealant andbacker-rod

Exterior faceof system

Drain opening

Approved Substrate

Lamella

Backer-rod

Drainagespace

AquaFlash®System

Dryvit waterresistivebarrier coating50.8mm

(2") min.

25.4mm(1") min.

R-002-07-08


Structural Expansion Joints



®


Notes:1. Dryvit recommends that ground floor applications and all façades exposed to abnormal stress, high traffic, or deliberate

impact have the base coat reinforced with Panzer ® 15 or 20 mesh prior to Standard Plus mesh. Location of high impactzones should be indicated on contract drawings.

2. Sealant should not be in direct contact with the AquaFlash System.3. Apply water-resistive barrier over remainder of wall surface.

Interior seal, by others

Dryvit AquaFlash®System (see note 2)

Approved substrate

Dryvit water-resistivebarrier coatingDryvit adhesive in verticalnotched trowel configuration

Lamella

Dryvit finish

Lamella



Dryvit Demandit™ or Color Prime™on surfaces to receive sealant

Dryvit AquaFlash System (see note 2)


Wrap Dryvit Detail Mesh 63.5 mm (212")

min. at backside of insulation slab

19 mm(3/4") min.

19 mm (3/4") min.

Dryvit compatiblesealant withclosed cellbacker-rod, by others

Dryvit Demandit® or Color Prime™on surfaces to receive sealant

Wrap Dryvit Detail Mesh™63.5 mm (21

2") min. atbackside of insulation slab


Interior seal,by others

BYOTHERS

DRYVITEXSULATION

L5000 SYSTEM


R-002-07-08


Penetrations



®

DRYVIT SYSTEMS CANADA129 Ringwood Drive PO Box 1268Stouffville, Ontario L4A 8A2800-263-3308www.dryvit.com

®


Approved substrate

Dryvit water-resistive barriercoating

Dryvit Demandit™ or ColorPrime™on surfaces to receivesealant


19 mm (3/4") min.

19 mm (3/4") min.

Wrap Dryvit Detail Mesh™63.5 mm (2 12 ") min. atbackside of lamella


Lamella


Dryvit finish


BY OTHERS

AquaFlash® System

Notes:


Dryvit Demandit orColor Prime

on surfaces toreceive sealant

Secondaryseal, by others

R-002-07-08


Wall Penetrations

Wrap insulation slab withDryvit Detail ReinforcingMesh

Dryvit Detail Reinforcing Mesh240 mm (9 1/2") x 300 mm (12")(typ.)

Lamella



®


®


Notes:


2. Locate lamella slabs suchthat slab edges do not alignwith corners of penetration.

3. Apply a piece of 240 mm (91/2") x 300 mm (12") detailreinforcing mesh diagonallyat each corner.

R-002-07-08


Sign Attachment

13 mm (1/2") min.




Lamella

Dryvit reinforcing meshembedded in base coatScrew/bolt attachment tobuilding framing/ blocking

Neoprene washer

Sign fixture

Dryvit compatible sealantand bond breaker tape, byothersSealant with bond breakertape between sleeve andDryvit water-resistive barriercoating, by others

Dryvit finish

BY OTHERS

Approvedsubstrate

Framingmember

Non-corrosivepipe sleeve

Blocking(secure to

framing)

BY OTHERS



®


®


InstallationInstructions:

1. Pre-drill through EIFSstopping at water-resistivebarrier (WRB).

2. Cut sleeve to equal depth ofsystem from WRB tooutside face.

3. Gun neutral cure siliconesealant into hole and insertsleeve.

4. While sealant is wet, installfastener and tool sealantaround edges as shown.

R-002-07-08


Aesthetic Reveals


19 mm (3/4") min.

Framingmember

BY OTHERS

Notes:


2. Slope bottom edge of revealfor positive drainage.

3. EPS can be used at reveallocation. This must bepre-approved by designauthority.


®


®


Approved substrate


63.5 mm (2 1/2")


Dryvit adhesive invertical notched trowelconfiguration

Dryvit Detail Mesh™embedded in base coat


Dryvit finish

LamellaEPS (Seenote 3)

R-002-07-08


Horizontal Joint at Stone Veneer



®


®



BY OTHERS

Notes:


Approved substrate

Dryvit water-resistive barrier coating

Dryvit adhesive in verticalnotched trowel configuration applied tolamella

Lamella notched to accommodateDryvit Drainage Strip, flashing, andDryvit AquaFlash® System lappedover flashing

Dryvit finish


Wrap Dryvit DetailMesh™ 63.5 mm (2 12 ")min. at backside oflamella

Dryvit Demandit™ or Color Prime™on surface(s) to receive sealant

19 mm (3/4") min.

Dryvit compatible sealant with closedcell backer-rod and weep tubes every600 mm (24"), by others

Continuous flashing, by others

Sealant with bond breaker, by others

Secondary barrier extendedbehind flashing, by others

Stone veneer system, by others

Dryvit DrainageStrip

Dryvit AquaFlashSystem

R-002-07-08


Soffit vent

Soffit vent by others

VARIES

VARIES

VARIES

VARIES

Uninsulated



®


®


Notes:


2. Caulk all butt joints,intersections, and end ofvents.

Substrate

Dryvit finish


Soffit vent by others

Dryvit adhesive

Lamella


Dryvit finish

Substrate

Insulated

R-002-07-08

exsulation l5000 dsc5002 lamella non combustible eifs · wrap dryvit detail mesh wrapped to...

Documents