fbthg-66chvl trunk hinge installation instructions
TRANSCRIPT
![Page 1: FBTHG-66CHVL Trunk Hinge Installation Instructions](https://reader036.vdocuments.net/reader036/viewer/2022081907/551a5b944a79598a0c8b465b/html5/thumbnails/1.jpg)
Important Technical Information: Fesler Billet makes every effort to ensure that you are provided with
the most accurate and up-to-date technical information. However, all
technical information is approximate and may vary upon application.
Fesler Billet is not responsible for any consequences resulting from
manufacture’s technical mid-year changes. Fesler Billet products
should only be installed by a qualified, licensed auto mechanic
experienced in the installation of such products.
Important Anodizing Information: Anodizing does not produce "flawless" color or finish on any Fesler
part ordered that way. In fact, you should expect to encounter minor
variations (or what some call "blemishes") in the color and finish in
individual pieces. Every Fesler finish is unique in this regard.
Remember, these variations are normal, and do not affect the
performance of the part in any way.
Other Important Stuff You Should Probably Read: Fesler Billet is not responsible for customer applications that are
outside the normal and intended use of our products, including
specific model and year applications.
Fesler Billet designs all parts off original OEM applications. Due to the
vast array of manufacturers for aftermarket parts, it is possible that you
may have to make some minor adjustments to either our part or your
sheet metal in order for the part to fit properly
QUESTIONS OR COMMENTS?
Call us at 1-866-583-9787
INSTALLATION INSTRUCTIONS
FBTHG-66CHVL
Trunk Hinges
1966 - 1967 Chevrolet Chevelle
![Page 2: FBTHG-66CHVL Trunk Hinge Installation Instructions](https://reader036.vdocuments.net/reader036/viewer/2022081907/551a5b944a79598a0c8b465b/html5/thumbnails/2.jpg)
INSTALLATION INSTRUCTIONS
1966-1967 Chevrolet Chevelle Trunk Hinges Copyright 2011 © by Fesler Productions, LLC. All rights reserved.
1. Remove four bolts retaining trunk lid and remove trunk lid
2. Remove trunk hinge springs. (Using vise grips or pliers will be helpful)
Each side has hooks on the body that the spring is locked
into.
3. Rotate the spring until the opposite end can be removed from the
hinge.
If you do not care about saving the springs you can cut
them with a die grinder to aid in the removal AFTER
SPRING TENSION IS RELEASED
4. With a die grinder carefully grind the head off the hinge pin
CAREFULLY, ***Be careful not to cut the outer body skin.
An angle die grinder works best. A mirror and light will
also be helpful.
Be sure to protect the carpet and all upholstery
5. After the head of the hinge pin is ground down remove the pin and
hinge.
6. Install new hinges with studs for the struts pointing out towards the
body
7. Line up the bushing with the
hinge pin hole and install the
provided pin. Insert the pin
from the center of the car.
>>>>>>>>
8. Install C-clip supplied on the new hinge pin
a. (Needle nose pliers would work best)
9. Using the lower strut mount as a template,
hold it against the trunk hinge support. Just
below the locking tabs for the old trunk
springs there is a step that the strut
bracket will line up with. Hold the bracket
against this lip and mount the bracket. The
bracket will extend past the hinge support 1” at the bottom corner. Use
and awl to mark the three holes.
10. Center punch and drill holes to 3/8”
using an angle drill. >>>>>>>>>>>>>
11. Install lower strut mount using the
three 3/8-16 x 1 ¾ button head
bolts, lock nuts and flat washers.
Remove retaining pins from strut
sockets and set aside (you will
need to replace them in step 12)
12. Pop struts onto ball studs with the
body attached to the hinge. Replace
strut retaining rings >>>>>>>>>>>>>
13. Reinstall trunk lid, attaching hinge to lid with supplied bolts and
washers.
14. Realign lid with car