fdx® (formula™ cge option included) and front riggings · g,i 1163181-nla nla - owner's...

FDX®(Formula™ CGE option included)

and Front Riggings

Power Wheelchair

Parts Catalog Issued: Jan 13, 2021

The information contained in this document is subject to change without notice. This catalog containsservice parts for Form No. 10-076. If you have any questions regarding this catalog, please contact oneof our Customer Service Representatives.

For Customer Service Support Call:1-800-333-6900

For Faxed In Orders Call:1-800-678-4682 or

1-440-366-0709For Technical Service Call:

1-800-832-4707Literature Can Be Found at:

www.invacare.com

SYMBOL DEFINITIONThroughout this catalog you will notice letters to draw your attention to specific footnotes which are located at thebottom of the page or below specified charts.

HARDWARE MEASUREMENTS

Examples:= Special Comments= General information pertaining to that specific page= No Longer Available

NOTE:NLA

The measurements for the hardware will be listed as follows:Screws, BoltsWashersSpacers

For your convenience, we have supplied an area for you to list your Invacare Representatives.

A,B,C etc.

Diameter X Thread Count/Pitch X LengthInside Diameter X Outside Diameter X ThicknessInside Diameter X Outside Diameter X Length

Name Phone Numbers

© 2021 Invacare Corporation. Elyria, Ohio. Invacare, Yes, you can., the Blue Medallion Design, FDX are registered trademarks and Formula, Contoura,Personal Back 10, DualFlex, MK6i, are trademarks of Invacare Corporation.

Otto Bock is a registered trademark owned by Otto Bock Orthopaedische Industrie GMBH & Co.. JAY Back is a registered trademark of Sunrise MedicalHHG, Inc. Corporation. Super Lube is a registered trademark of Synco Chemical Corporation.

Parts Catalog Usage Guide

1Form No. 10-076 To order call toll free 1-800-333-6900, or www.invacare.com

A: READ THIS FIRST (THIS CATALOG IS DIFFERENT!) ...................................................... 5

Accessories - Adductors ........................................................................................................... 144

Accessories - Compact Vent Assembly ................................................................................... 141

Accessories - Miscellaneous .................................................................................................... 146

Accessories - Oxygen Holder Assembly Kit ............................................................................. 139

Actuator Motor - Elevate & Mounting Hardware - CGE ............................................................ 14

Anti-Tip Assembly - Front (After 8/1/11) ................................................................................... 22

Anti-Tip Assembly - Front (Before 8/2/11) ................................................................................ 20

Arms - "T" & Hardware ............................................................................................................. 103

Arms - Cantilever ...................................................................................................................... 119

Arms - Mtg. Front/Rear Arm Socket Asbly. & Hdwr. (12" - 16" W x 12" - 18" D) ...................... 113

Arms - Mtg. Front/Rear Arm Socket Asbly. & Hdwr. (16" - 22" W x 16" - 22" D) ...................... 115

Arms - Mtg. Front/Rear Arm Socket Asbly. & Hdwr. (16" - 22" W x 16" - 22" D) TRRO Option 117

Arms - Mtg. Swingaway Hardware ........................................................................................... 111

Arms - w/o Mtg. Hdwr. - Adjustable Height (12" - 16" W x 12" - 15" D) .................................... 105Arms - w/o Mtg. Hdwr. - Adjustable Height (12" - 16" W x 16" - 18" D) & (16" - 22" W x 16" - 22"D) 107

Arms - w/o Mtg. Hdwr. - Fixed Height (16" - 22" W x 16" - 22" D) ............................................ 109

Backs - Conventional without Mounting Hardware - (12" - 15" W) ........................................... 65

Backs - Curve Contoura without Mounting Hardware .............................................................. 68

Backs - Metal Curved Assembly (16" - 22" W) ......................................................................... 72

Backs - Mounting Hardware - Conventional (12" - 15" W) ....................................................... 77

TABLE of CONTENTSDescription Page

Number

2To order call toll free 1-800-333-6900, or www.invacare.comForm No. 10-076

Backs - Mounting Hardware - Curve Contoura ........................................................................ 78

Backs - Mounting Hardware - Metal Curved (16" - 22" W) ....................................................... 80

Backs - Recliner Assembly - ADJRECL Seat Frames ............................................................. 81

Battery Box Assembly - Battery Box Isolation Shroud & Battery Retainer Brackets ................ 12

Battery Chargers & Cables ....................................................................................................... 18

Battery Wire Harnesses & Battery Straps ................................................................................ 16

Canes - Back - Mounting Hardware - ADJASBA Seats (12" - 16" W) ...................................... 95Canes - Back - Mounting Hardware - Metal Curved Back - Curve Contoura - BPO Option (16" -22" W) 101

Canes - Back - Mounting Hardware - Nylon Upholstery (16" - 22" W) ..................................... 97

Canes - Back - Mounting Hardware - Nylon Upholstery (16" - 22" W) TRRO Option .............. 99Canes - Back & Spreader Bar/Push Handle Asbly. - Sling Nylon Back Uph. (12" - 16" W) -Conv. Back (12" - 15" W) 89

Canes - Back & Spreader Bars - ADJASBA Seats (16" - 22" W) ............................................. 92

Caster & Forks - Rear .............................................................................................................. 48

Cushions - Seat - Curve Contoura Seating .............................................................................. 62

Electronics - MK6i ~PLEASE READ FIRST ............................................................................. 122

Frames - Seat ADJASBA - Seat Pan & Hdwr. - (12" - 16" W) .................................................. 52

Frames - Seat ADJASBA Mtg. Hdwr. - Elevate - CGE (12" - 22" W) ....................................... 60

Frames - Seat ADJASBA Mtg. Hdwr. - Non-Elevate (12" - 22" W) .......................................... 58

Frames - Seat ADJASBA/ADJRECL - Seat Pan & Hdwr. (16" - 20" W x 16" - 22" D) ............. 54

Frames - Seat ADJASBA/ADJRECL - Seat Pan & Hdwr. (20" - 22" W x 16" - 22" D) ............. 56

Front Riggings - Center Mount Front Rigging (CTMT-FJ/CTMT-F) ......................................... 123


Number


Front Riggings - Center Mount Rigging (CTMT-F w/ CTMTFB One PC Flip-Up Footboard) ... 131

Front Riggings - Center Mount Rigging Mtg. Hdwr. (CTMT-F/CTMT-FJ) (12" - 22" W) ........... 135Front Riggings - Center Mount Rigging w/ Adductors Mtg. Hdwr. (CTMT-F/CTMT-FJ) (12" - 22"W) 137

Label Locations For TRRO & TRBKTS Options ....................................................................... 10

Motor - 2-Pole, SSD Gearbox & Mounting Hardware ............................................................... 24

Motor - 4-Pole, SSD Gearbox & Mounting Hardware ............................................................... 27

Packaging - Literature & Decals ............................................................................................... 7

Shroud Finishes - Touch-Up Paints & Upholstery Option ........................................................ 6

Shrouds & Hardware - Conversion Kits - w/ Lights Before 07/11/11 ........................................ 38

Shrouds & Hardware - Conversion Kits - w/o Lights Before 07/11/11 ...................................... 35

Shrouds & Hardware - w/ Lights After 07/10/11 ....................................................................... 44

Shrouds & Hardware - w/o Lights After 07/10/11 ..................................................................... 40

Swing Arm & Hardware ............................................................................................................ 31

TRRO & TRBKTS Option Clarification Reference .................................................................... 9

TRRO Instruction Cards ........................................................................................................... 11

Upholstery - Back - Non-Recliner - Nylon ................................................................................ 84

Upholstery - Back - Recliner - Nylon ........................................................................................ 86

Upholstery - Headrest & Pillows ............................................................................................... 88

Warranty Replacement Parts ................................................................................................... 149

Wheel Lock Assembly .............................................................................................................. 33

Wheels - Drive Wheels & Mounting Hardware (14" x 3") ......................................................... 50


Number


A: READ THIS FIRST (THIS CATALOG IS DIFFERENT!)


Shroud Finishes and Touch-Up Paint

Color Number Part Number Bottle Size Shroud FinishWet Black.6 oz.1031450-NLA24P

Silver Metallic.6 oz.1101318-NLA 60P See Note(s) A

Electric Red.6 oz.1046321-NLA61PElectric Blue.6 oz.1046320-NLA62PArtic WhiteN/AN/A143P

Electric Silver.6 oz.1101318-NLA 147P See Note(s) A

A - Part #1101318 is used for both 60P Silver Metallic Frame Finish and 147P Electric Silver Shroud Finish. NOTE:

Upholstery Option

Nylon Color U240 Black

Shroud Finishes, Touch-Up Paints and Upholstery Option


Packaging, Literature and Decals


Packaging, Literature and DecalsItem

Number Part Number DescriptionNoteQuantity Per

Package Assembly1030365 Carton, Cover 1 11 A1030364 Carton, Cover 1 11 B1031682 Carton, Cover 1 11 C1036028 Carton, Cover 1 11 D

40131X161 Insert, Plain Pad 1 2240131X011 Carton, Front Riggings 1 13

1012001-NLA NLA - Carton, Joystick 1 14 J1030362 Carton, Tray 1 25 E1036027 Carton, Tray 1 25 F1115174 Carton, Corner Reinforcement 1 46 E

1129589-NLA Carton, Corner Reinforcement 1 46 C1129590-NLA Carton, Corner Reinforcement 1 46 F1163181-NLA NLA - Owner's Manual, FDX Base 1 1G,I1143192-NLA NLA - Owner's Manual, ADJASBA Seat with MK6i

Electronics1 1G

1167400-NLA NLA - Decal, FDX Model, Swing Arm 1 2G1168380-NLA NLA - Decal, Invacare Logo, Fender - Right 1 1G1168381-NLA NLA - Decal, Invacare Logo, Fender - Left 1 1G

1104802 Decal, Push/Drive 1 2G1083199-NLA NLA - Label, Hook Tie-Down 1 4G,H

1079203 Decal, Warning Pinch Point 1 2G1119281-NLA NLA - Plate, Name, Patent Numbers 1 1G

1035900 Decal, Transportation 1 1GA - Base only and all ADJASBA seat only models B - 12" Wide - 20" Wide ADJASBA seat with base models C - 16" Wide - 20" Wide ADJASBA seat with base models with medium and tall seat-to-floor heights D - 21" Wide - 22" Wide ADJASBA seat with base models E - 12" Wide - 20" Wide ADJASBA seat with base and base only models F - 21" Wide - 22" Wide ADJASBA seat with base models G - Not Shown H - For TRRO/TRBKTS wheelchairs only I - Item is no longer available from the Invacare Service Department. Refer to the Invacare Website under "Product Literature

Search". Enter the part number in the "Keywords" field and download a free PDF copy. J - Order item #3 part #40131X011 to use as a replacement Joystick Carton also.

When adjusting or replacing parts, please refer to your Owner's Manual for assistance.

NOTE:


TRRO and TRBKTS Option Clarification ReferenceTRRO and TRBKTS Option is an On-Chair option only.


Label Locations For TRRO and TRBKTS Options


ItemNumber Part Number DescriptionNote

Quantity PerPackage Assembly

1152750-NLA NLA - Card, TRRO Instruction 1 11 A1026298 Package, Screw with Washer (#10 x 7/8") (Pair) 2 12

A - Instruction Cards include the attachment strap. Individual components are non-saleable. Serial number of chair must be verified to ensure that TRRO option was originally ordered.

NOTE:

TRRO Instruction Cards


Battery Box Assembly, Battery Box Isolation Shroud andBattery Retainer Brackets

Non-serviceable parts in the field require the wheelchair to be returned to Invacare for repair. CallTechnical Services for assistance (1-800-832-4707)


Battery Box Assembly, Battery Box Isolation Shroud andBattery Retainer Brackets




1168906-NLA NLA - Kit, Battery Box Isolation Shroud 1 11 AShroud, Battery Box Isolation 1 12Tie Wrap (11-1/2" L) 1 43

1162568 Kit, Battery Retainer Brackets and Hardware 1 14 BBracket, Battery Retainer, Black - Right 1 15Bracket, Battery Retainer, Black - Left 1 16NLA - Locknut (M8 x 1.25) 1 27NLA - Bolt, Round Head Square Neck (M8 x 1.25 x20mm)

1 28A - Includes items 2 and 3 B - Includes items 5-8

NOTE:


Elevate Actuator Motor and Mounting HardwareCGE


Elevate Actuator Motor and Mounting HardwareCGE



1168911 Actuator Motor Assembly, Elevate 1 111168908 Kit, Elevate Actuator Mounting Hardware 1 12 A

Screw, Hex Head w/ Patch (M8 x 1.25 x 20mm) 1 43NLA - Washer, Steel (8.4mm x 16mm x 1.6mm) 1 44

1168907 Kit, Elevate Support Bracket and Hardware 1 15 BNLA - Washer, Steel (8.4mm x 16mm x 1.6mm) 1 24NLA - Locknut (M8 x 1.25) 1 26NLA - Bolt, Round Head Square Neck (M8 x 1.25 x20mm)

1 27Bracket, Elevate Mounting, Black 1 18Isolator, Rubber 1 19Screw, Socket Head w/ Patch (M8 x 1.25 x 25mm) 1 210

1168909 Kit, Sensor, Proximity Switch and Hardware 1 111 CSensor, Proximity Switch (7" L) 1 112NLA - Screw, Phillips Pan Head (#4-40 x 3/8") 1 213NLA - Washer, Plain (1/8 x 5/16 x 1/32") 1 214

1163047 Bracket, Elevate Actuator Mounting, Black 1 1151166200-NLA NLA - Elevate Actuator Switch and Mounting

Bracket Assembly1 116 D

A - Includes items 3 and 4 B - Includes items 4 and 6-10 C - Includes items 12-14. D - Item #11 Proximity Switch Sensor mates up with item #16 to establish a connection. Item #16 shares hardware with the

Seat Frame Mounting Hardware. See page titled "ADJASBA Seat Frame Mounting Hardware - Elevate (CGE)" for additional assembly information.

NOTE:


Battery Wire Harnesses and Battery Straps


Battery Wire Harnesses and Battery StrapsItem


Package Assembly1168893 Kit, Battery Wire Harness with Terminal Hardware,

GP34 - Rear1 11 A

Washer, Lock (1/4 x 1/2 x 1/16") 1 42NLA - Bolt, Hex Head Cap (1/4-20 x 3/4") 1 23Tie Wrap (11-1/2" L) 1 24Harness, Battery Wire, GP34 - Rear 1 15

1168894 Kit, Battery Wire Harness with Terminal Hardware,GP34 - Front

1 16 BWasher, Lock (1/4 x 1/2 x 1/16") 1 42NLA - Bolt, Hex Head Cap (1/4-20 x 3/4") 1 23Tie Wrap (11-1/2" L) 1 24Harness, Battery Wire, GP34 - Front 1 17

1095502-NLA NLA - Package, Tie Wrap (11-1/2" L) 10 141168892-NLA NLA - Strap, Battery (Pair) 2 18

A - Includes items 2-5 B - Includes items 2-4 and 7

NOTE:


Battery Chargers and Cables


Battery Chargers and CablesItem


Package Assembly1053161-NLA NLA - Charger, Battery, 8 Amp, 115vac, Off Board

Dual Mode Round Plug, Lester1 11 E

1123249 Charger, Battery, 8 Amp. 115vac (Off Board) Single Mode Round Plug w/ AC Power Line Cord

1 11 A1123249E-NLA NLA - WARR RPLMT - Charger, Battery, 8 Amp,

115VAC (Off Board) Single Mode Round Plug w/ AC Power Line Cord

1 11 A

1089627-NLA NLA - Cord, AC Power, 115VAC, 2 Prong Off-Board(11' 6" L)

1 12 D1121086 Cord, AC Power, 115VAC, 3 Prong On-Board (6'

6-1/2" L)1 12

1144926 Cable, Drive Lockout Sensor, MK6i 1 13 B1168910 Kit, Battery Cable Assembly and Attaching

Hardware1 14 C

Battery Cable Assembly 1 15Nut, Hex Prev-Torq (M3 x .5) 1 46Screw, Socket Button Head (M3 x .5 x 25mm) 1 47

A - CTE charger is standard on-chair. Used on Gel Cell or AGM (Absorbed Glass Mat) batteries. For wet cell batteries refer to the Lester charger part number 1053161.

B - Drive Lockout Sensor Cable used for chairs manufactured with a ADJRECL Seat Frame. C - Includes items 5-7 D - No longer available as a service part. Please use 1121086 as its replacement. E - Use Battery Charger part number 1123249 as a replacement.

NOTE:


Anti-Tip Assembly - Front (Before 8/2/11)Non-serviceable parts in the field require the wheelchair to be returned to Invacare for repair. Call

Technical Services for assistance (1-800-832-4707)


Anti-Tip Assembly - Front (Before 8/2/11)Non-serviceable parts in the field require the wheelchair to be returned to Invacare for repair. Call

Technical Services for assistance (1-800-832-4707)Item


Package Assembly1168887 NLA - Kit, Anti-Tip Wheel Assembly and Hardware 1 11 A

NLA - Screw, Socket Button Head (M8 x 1.25 x60mm)

1 12NLA - Washer, Steel (8.4mm x 16mm x 1.6mm) 1 23NLA - Nut, Acorn (M8 x 1.25) 1 14Wheel Assembly, Composite, Urethane (5" x 1") 1 15

1168888 Package, Plug Button, Square, Black (1") (Pair) 2 16A - Includes items 2-5 and accommodates one side only. NOTE:


Anti-Tip Assembly - Front (After 8/1/11)Non-serviceable parts in the field require the wheelchair to be returned to Invacare for repair. Call



Anti-Tip Assembly - Front (After 8/1/11)Non-serviceable parts in the field require the wheelchair to be returned to Invacare for repair. Call



Package Assembly1176373 Kit, Anti-Tip Wheel Assembly and Hardware 1 11 A

Screw, Socket Button Head w/ Patch (M8 x 1.25 x40mm)

1 12NLA - Washer, Steel (8.4mm x 16mm x 1.6mm) 1 23Wheel Assembly, Composite, Urethane (5" x 1") 1 14

A - Includes items 2-4 and accommodates one side only. NOTE:


Motor, 2-Pole, SSD Gearbox and Mounting Hardware


Motor, 2-Pole, SSD Gearbox and Mounting HardwareItem


Package Assembly1168983 Kit, 2-Pole Low Speed Motor/23:1 SSD Gearbox

Assembly - Right1 11 A,J,K

2-Pole Low Speed Motor/23:1 SSD GearboxAssembly - Right

1 1Decal, Motor Warning 1 1Instruction Sheet, Installation 1 1Grease, Super Lube (1cc Tube) 1 1

1168984 Kit, 2-Pole Low Speed Motor/23:1 SSD GearboxAssembly - Left

1 11 A,J,K2-Pole Low Speed Motor/23:1 SSD GearboxAssembly - Left


1168883 Package, Coupling/Cup Assembly 10 161179216 Kit, Motor Assembly, 2-Pole Low Speed 1 12 B,K

Motor Assembly, 2-Pole Low Speed 1 13Screw, Phillips Pan Head Tap (M4 x .7 x 6mm) 1 14Decal, Motor Warning 1 15Decal, Push/Drive 1 1Clamp, Band 1 17Locknut (M6 x 1) 1 18Washer, Plain (1/4 x 1/2 x 9/16") 1 19Spacer, Clamp, Molded 1 110Bolt, Round Head Square Neck (M6 x 1 x 35mm) 1 111Instruction Sheet, Installation 1 1Grease, Super Lube (1cc Tube) 1 1

1179222 Kit, SSD Gearbox Assembly, 23:1 - RWD/FWD-Left& CWD-Right

1 116 C,J,KClamp, Band 1 17Locknut (M6 x 1) 1 18Washer, Plain (1/4 x 1/2 x 9/16") 1 19Spacer, Clamp, Molded 1 110Bolt, Round Head Square Neck (M6 x 1 x 35mm) 1 111Gearbox Assembly, SSD, 23:1 - RWD/FWD-Left &CWD-Right

1 112Instruction Sheet, Installation 1 1Grease, Super Lube (1cc Tube) 1 1

1179221 Kit, SSD Gearbox Assembly, 23:1 -RWD/FWD-Right & CWD-Left

1 116 C,J,KClamp, Band 1 17Locknut (M6 x 1) 1 18Washer, Plain (1/4 x 1/2 x 9/16") 1 19Spacer, Clamp, Molded 1 110Bolt, Round Head Square Neck (M6 x 1 x 35mm) 1 111


Motor, 2-Pole, SSD Gearbox and Mounting HardwareItem


Package AssemblyGearbox Assembly, SSD, 23:1 - RWD/FWD-Right &CWD-Left


1169005 Kit, Brake Lever Assembly w/ Set Screw, 2-PoleMotor (Pair)

1 113 GBrake Lever Assembly w/ Set Screw, 2-Pole Motor -Right

1 1Brake Lever Assembly w/ Set Screw, 2-Pole Motor -Left

1 11168665-NLA NLA - Screw, Set Socket Cup Point w/ Patch (M5 x

.8 x 6mm)-- --M

1168884 Kit, Motor/SSD Gearbox Band Clamp and Hardware 1 114 DClamp, Band 1 17Locknut (M6 x 1) 1 18Washer, Plain (1/4 x 1/2 x 9/16") 1 19Spacer, Clamp, Molded 1 110Bolt, Round Head Square Neck (M6 x 1 x 35mm) 1 111Instruction Sheet, Installation 1 1Grease, Super Lube (1cc Tube) 1 1

1169645 Package, Screw, Hex Head w/ Patch (M8 x 1.25 x60mm)

4 115 E,I1160525 Kit, Brushes with Caps, 2-Pole 1 1F

Brush, Motor, 2-Pole 1 2Cap, Brush 1 2Instruction Sheet 1 1

1101725 Cap, Brake Lever End, Black 1 1H1130584 Package, Cap, Brake Lever End, Black 10 1H1180609 Package, Grease, Super Lube (1cc Tube) (Pkg. of

10)10 1L

A - Includes items 3-12, Super Lube Grease, Instruction Sheet and Push/Drive Decal. For FDX Model only: Push/Drive Decal is attached to Swing Arm.

B - Includes items 3-5, 7-11, Super Lube Grease, Instruction Sheet and Push/Drive Decal. For FDX Model only: Push/Drive Decal is attached to Swing Arm. The Motor can be used on the right or left side of the wheelchair.

C - Includes items 8-12, Super Lube Grease and Instruction Sheet. D - Includes items 7-11. E - Screw Package is used to attach the Motor/Gearbox Assembly to the Swing Arm. F - Not Shown. Kit includes (2) Brushes, (2) Brush Caps and Instruction Sheet. G - Brake Lever Assembly sold as a pair that includes the right and left side Brake Levers, (2) ea. Brake Lever End Caps , (2)

ea. Set Screws - see part #1168665 to order separately. Brake Lever End Cap can be sold separately. See part #1101725. H - Not Shown. Brake Lever End Cap attaches to item 13 Brake Lever Assembly.

I - Material was added to the SSD Gearbox around the 5 mounting holes on the output side 7/11/11. The Mounting Hex Head Screw was also changed from 55mm to 60mm. The 60mm Hex Head Screw is Backward Compatible to all SSD Gearboxes manufactured Before 7/11/11.

J - Material was added to the SSD Gearbox around the 5 mounting holes on the output side 7/11/11. Item #15 (Package, Screw, Hex Head w/ Patch (M8 x 1.25 x 60mm)) must also be ordered for wheelchairs manufactured Before 7/11/11.

K - Before placing an order, it is recommended to call Invacare's Technical Service Department at (1-800-832-4707) to verify if the Motor, SSD Gearbox or the Motor/SSD Gearbox Assembly is needed.

L - Not Shown. Super Lube Grease is applied to the Gearbox Output Shaft. M - Not Shown. Use part #1168665 Screw, Set Socket Cup Point w/ Patch (M5 x .8 x 6mm) to hold item #13 Brake Lever in

place.

NOTE:

26

To order call toll free 1-800-333-6900, or www.invacare.comForm No. 10-076

Motor, 4-Pole, SSD Gearbox and Mounting Hardware4-Pole Motors are used when the Drive Type Option PERF is selected on-chair. Replacement Motor Brush

and Cap is not available for the 4-Pole motor listed.



and Cap is not available for the 4-Pole motor listed.Item


Package Assembly1168988 Kit, 4-Pole High Speed Motor/18:1 SSD Gearbox

Assembly - Right1 11 A,J,K

4-Pole High Speed Motor/18:1 SSD GearboxAssembly - Right


1168989 Kit, 4-Pole High Speed Motor/18:1 SSD GearboxAssembly - Left

1 11 A,J,K4-Pole High Speed Motor/18:1 SSD GearboxAssembly - Left


1168883 Package, Coupling/Cup Assembly 10 161179218-NLA NLA - Kit, Motor Assembly, 4-Pole High Speed 1 12 B,K,N

Motor Assembly, 4-Pole High Speed 1 1Screw, Phillips Pan Head Tap (M4 x .7 x 6mm) 1 1Decal, Motor Warning 1 1Decal, Push/Drive 1 1Clamp, Band 1 1Locknut (M6 x 1) 1 1Washer, Plain (1/4 x 1/2 x 9/16") 1 1Spacer, Clamp, Molded 1 1Bolt, Round Head Square Neck (M6 x 1 x 35mm) 1 1Instruction Sheet, Installation 1 1Grease, Super Lube (1cc Tube) 1 1

1195983 Kit, Motor Assembly, 4-Pole High Speed 1 12 B,KMotor Assembly, 4-Pole High Speed 1 1Decal, Motor Warning 1 1Decal, Push/Drive 1 1Label, Refer To User Manual 1 1Clamp, Band 1 1Locknut (M6 x 1) 1 1Washer, Plain (1/4 x 1/2 x 9/16") 1 1Spacer, Clamp, Molded 1 1Bolt, Round Head Square Neck (M6 x 1 x 35mm) 1 1Instruction Sheet, Installation 1 1Sheet, Insert Parts Service 1 1Grease, Super Lube (1cc Tube) 1 1

1179219 Kit, SSD Gearbox Assembly, 18:1 -RWD/FWD-Right & CWD-Left

1 116 C,J,KClamp, Band 1 17Locknut (M6 x 1) 1 18



and Cap is not available for the 4-Pole motor listed.Item


Package AssemblyWasher, Plain (1/4 x 1/2 x 9/16") 1 19Spacer, Clamp, Molded 1 110Bolt, Round Head Square Neck (M6 x 1 x 35mm) 1 111Gearbox Assembly, SSD, 18:1 - RWD/FWD-Right &CWD-Left


1179220 Kit, SSD Gearbox Assembly, 18:1 - RWD/FWD-Left& CWD-Right

1 116 C,J,KClamp, Band 1 17Locknut (M6 x 1) 1 18Washer, Plain (1/4 x 1/2 x 9/16") 1 19Spacer, Clamp, Molded 1 110Bolt, Round Head Square Neck (M6 x 1 x 35mm) 1 111Gearbox Assembly, SSD, 18:1 - RWD/FWD-Left &CWD-Right


1169004 Kit, Brake Lever Assembly w/ Set Screw, 4-PoleMotor (Pair)

1 113 GBrake Lever Assembly w/ Set Screw, 4-Pole Motor -Right

1 1Brake Lever Assembly w/ Set Screw, 4-Pole Motor -Left

1 11168665-NLA NLA - Screw, Set Socket Cup Point w/ Patch (M5 x

.8 x 6mm)1 1M

1168884 Kit, Motor/SSD Gearbox Band Clamp and Hardware 1 114 DClamp, Band 1 17Locknut (M6 x 1) 1 18Washer, Plain (1/4 x 1/2 x 9/16") 1 19Spacer, Clamp, Molded 1 110Bolt, Round Head Square Neck (M6 x 1 x 35mm) 1 111Instruction Sheet, Installation 1 1Grease, Super Lube (1cc Tube) 1 1

1169645 Package, Screw, Hex Head w/ Patch (M8 x 1.25 x60mm)

4 115 I1101725 Cap, Brake Lever End, Black 1 1H1130584 Package, Cap, Brake Lever End, Black 10 1H1180609 Package, Grease, Super Lube (1cc Tube) (Pkg. of

10)10 1L



and Cap is not available for the 4-Pole motor listed.A - Includes items 3-12, Super Lube Grease, Instruction Sheet and Push/Drive Decal. For FDX Model only: Push/Drive Decal

is attached to Swing Arm. B - Includes items 3-5, 7-11, Super Lube Grease, Instruction Sheet and Push/Drive Decal. For FDX Model only: Push/Drive

Decal is attached to Swing Arm. The Motor can be used on the right or left side of the wheelchair. C - Includes items 8-12, Super Lube Grease and Instruction Sheet. D - Includes items 7-11. G - Brake Lever Assembly sold as a pair that includes the right and left side Brake Levers, (2) ea. Brake Lever End Caps , (2)

ea. Set Screws - see part #1168665 to order separately. Brake Lever End Cap can be sold separately. See part #1101725. H - Not Shown. Brake Lever End Cap attaches to item 13 Brake Lever Assembly.

I - Material was added to the SSD Gearbox around the 5 mounting holes on the output side 7/11/11. The Mounting Hex Head Screw was also changed from 55mm to 60mm. The 60mm Hex Head Screw is Backward Compatible to all SSD Gearboxes manufactured Before 7/11/11.

J - Material was added to the SSD Gearbox around the 5 mounting holes on the output side 7/11/11. Item #15 (Package, Screw, Hex Head w/ Patch (M8 x 1.25 x 60mm)) must also be ordered for wheelchairs manufactured Before 7/11/11.

K - Before placing an order, it is recommended to call Invacare's Technical Service Department at (1-800-832-4707) to verify if the Motor, SSD Gearbox or the Motor/SSD Gearbox Assembly is needed.

L - Not Shown. Super Lube Grease is applied to the Gearbox Output Shaft. M - Not Shown. Use part #1168665 Screw, Set Socket Cup Point w/ Patch (M5 x .8 x 6mm) to hold item #13 Brake Lever in

place. N - No Longer Available. For replacement order part number 1195983. Order in pairs to match when replacing part number

1179218.

NOTE:


Swing Arm and HardwareNon-serviceable parts in the field require the wheelchair to be returned to Invacare for repair. Call



Swing Arm and HardwareNon-serviceable parts in the field require the wheelchair to be returned to Invacare for repair. Call



Package Assembly1168895 Kit, Swing Arm Mounting Hardware 1 21 A

Spacer, Coved (3/4 x 1-1/8 x 1-1/32") 1 12Locknut (M14 x 2) 1 13Washer (14mm x 28mm x 2mm) 1 14

1168886 Kit, Stop Blocks and Hardware (Pair) 1 15 BBlock, Stop, 14" Wheel - Right 1 16Block, Stop, 14" Wheel - Left 1 16Screw, Socket Head (M5 x .8 x 25mm) 1 47

1168896 Spring, Non-Heavy Duty (Pair) 2 18 C1168897 Spring, Heavy Duty (Pair) 2 18 D1104802 Decal, Push/Drive 1 29

A - Includes items 2-4. B - Includes items 6 and 7. C - Non-Heavy Duty Spring is used for Formula CG powered seating systems w/o Vent or COMP. D - Heavy Duty Spring is used for ADJASBA and ADJRECL non-powered seating systems or Formula CG powered seating

systems w/ Vent or COMP .

NOTE:


Wheel Lock Assembly


Wheel Lock AssemblyItem


Package Assembly1169217-NLA NLA - Wheel Lock Assembly - Right 1 11 C1169218-NLA NLA - Wheel Lock Assembly - Left 1 11 C

1127688 Package, Plastic Tip, Black 10 1A1170676-NLA NLA - Kit, Wheel Lock Mounting Hardware (Pair) 1 12 B

Screw, Socket Head Cap w/ Patch (M6 x 1 x 65mm) 1 43Washer (1/4 x 1/2 x 1/16") 1 44Nut, Weld (M6 x 1 x 69.60mm Spacing) 1 25

A - Not Shown. B - Includes items 3-5. C - Holes were added to the Swing Arms on 1/7/11 to accommodate Wheel Lock Assemblies. Wheelchair manufactured

before 1/7/11must be returned to Invacare in order to replace the Swing Arms and then have the Wheel Locks installed.

NOTE:


Shrouds & Hardware - Conversion Kitsw/o Lights Before 07/11/11

Shrouds manufactured before 07/11/11 are no longer available. Shroud Conversion Kits must be ordered.NOTE: Retrofit Kit to add Lights in the field is not available. The wheelchair must be returned to Invacare

utilizing the Mechanical Repair Quote Form.




utilizing the Mechanical Repair Quote Form.Item


Package Assembly1168998 Package, Lens Reflective Insert 4 11 A,B1165607 Bezel, Lighting - Right 1 12 A1165608 Bezel, Lighting - Left 1 12 A

60102804 Kit, Cover, Lighting Bezel Lens - Right 1 1360102805 Kit, Cover, Lighting Bezel Lens - Left 1 13See Chart Item #4 Shroud Conversion Kit - Non-Elevate w/o

Lights1 14

See Chart Item #5 Shroud Conversion Kit - Elevate w/o Lights 1 15A - Item #'s 1-3 are not included with the Conversion Kits. If the customer is not able to reuse their existing components, order

the items required in addition to the Conversion Kit. B - Item #1 Lens Reflective Insert covers the holes inside item #2 Bezel when the Lighting Option is not ordered.

NOTE:

Item #4 Shroud Conversion Kit

Non-Elevate w/o LightsShroud Color Part Number

1174608-NLA Wet Black (24P) See Note(s) A

1174609-NLA Artic White (143P) See Note(s) A

1174610-NLA Electric Silver (147P) See Note(s) B, A

1174611-NLA Electric Red (61P) See Note(s) A

1174612-NLA Electric Blue (62P) See Note(s) A

A - Conversion Kit includes a revised Controller Mounting Bracket Assembly, Rear Shroud, Swing Arm Shrouds, Fender Shrouds,Front Shroud w/ Bracket Assembly, Decals, Mounting Hardware - use existing swing arm shroud screws, and InstallationInstructions. B - As of 11/2/11 Silver Metallic (60P) was replaced with Electric Silver (147P). Wheelchairs manufactured before 11/2/11 mustorder the Electric Silver (147P) Shroud and Hardware Conversion Kit.

NOTE:

Item #'s 1-3 are not included with the Conversion Kits. If the customer is not able to reuse their existing components, order the items requiredin addition to the Conversion Kit.

Item #5 Shroud Conversion KitElevate w/o Lights

Shroud Color Part Number1174613-NLA

Wet Black (24P) See Note(s) A1174614-NLA

Artic White (143P) See Note(s) A1174615-NLA

Electric Silver (147P) See Note(s) A, B36

To order call toll free 1-800-333-6900, or www.invacare.comForm No. 10-076



utilizing the Mechanical Repair Quote Form.Item #5 Shroud Conversion Kit

Elevate w/o Lights


Electric Red (61P) See Note(s) A1174617-NLA

Electric Blue (62P) See Note(s) AA - Conversion Kit includes a revised Controller Mounting Bracket Assembly, Rear Shroud, Swing Arm Shrouds, Fender Shrouds,Front Shroud w/ Bracket Assembly, Decals, Mounting Hardware - use existing swing arm shroud screws, and InstallationInstructions. B - As of 11/2/11 Silver Metallic (60P) was replaced with Electric Silver (147P). Wheelchairs manufactured before 11/2/11 mustorder the Electric Silver (147P) Shroud and Hardware Conversion Kit.

NOTE:

Item #'s 1-3 are not included with the Conversion Kits. If the customer is not able to reuse their existing components, order the items requiredin addition to the Conversion Kit.


Shrouds & Hardware - Conversion Kitsw/ Lights Before 07/11/11


utilizing the Mechanical Repair Quote Form.


Shrouds & Hardware - Conversion Kitsw/ Lights Before 07/11/11


utilizing the Mechanical Repair Quote Form.Item #1 Shroud Conversion Kit

Non-Elevate w/ LightsShroud Color Part Number

1174620-NLA Wet Black (24P) See Note(s) A

1174621-NLA Artic White (143P) See Note(s) A

1174622-NLA Electric Silver (147P) See Note(s) A, B

1174623-NLA Electric Red (61P) See Note(s) A

1174624-NLA Electric Blue (62P) See Note(s) A

A - Conversion Kit includes a revised Controller Mounting Bracket Assembly, Rear Shroud, Swing Arm Shrouds, Fender Shrouds w/Head Light Assembly, Front Shroud w/ Bracket Assembly, Decals, Shrouds and Bezel Mounting Hardware, and InstallationInstructions. B - As of 11/2/11 Silver Metallic (60P) was replaced with Electric Silver (147P). Wheelchairs manufactured before 11/2/11 mustorder the Electric Silver (147P) Shroud and Hardware Conversion Kit.

NOTE:

Item #2 Shroud Conversion KitElevate w/ Lights


Wet Black (24P) See Note(s) A1174626-NLA

Artic White (143P) See Note(s) A1174627-NLA

Electric Silver (147P) See Note(s) A, B1174628-NLA

Electric Red (61P) See Note(s) A1174629-NLA

Electric Blue (62P) See Note(s) AA - Conversion Kit includes a revised Controller Mounting Bracket Assembly, Rear Shroud, Swing Arm Shrouds, Fender Shrouds w/Head Light Assembly, Front Shroud w/ Bracket Assembly, Decals, Shrouds and Bezel Mounting Hardware, and InstallationInstructions. B - As of 11/2/11 Silver Metallic (60P) was replaced with Electric Silver (147P). Wheelchairs manufactured before 11/2/11 mustorder the Electric Silver (147P) Shroud and Hardware Conversion Kit.

NOTE:


Shrouds and Hardwarew/o Lights After 07/10/11





1168901-NLA NLA - Kit, Shrouds and Bezel Mounting Hardware 1 11 AScrew, Thumb w/ Shoulder (M9.5 x 24.13mm, M6 x1)

1 42Screw, Thumb (M5 x .8 x 12mm) 1 43Screw, Phillips Pan Head Tap (#10-32 x 3/8") 1 24Screw, Phillips Pan Head SEMS w/ Patch (M3 x .5 x10mm)

1 251167400-NLA NLA - Decal, FDX Model, Swing Arm 1 271168380-NLA NLA - Decal, Invacare Logo, Fender - Right 1 181168381-NLA NLA - Decal, Invacare Logo, Fender - Left 1 18

1165607 Bezel, Lighting - Right 1 191165608 Bezel, Lighting - Left 1 191168998 Package, Lens Reflective Insert 4 110

60102804 Kit, Cover, Lighting Bezel Lens - Right 1 11160102805 Kit, Cover, Lighting Bezel Lens - Left 1 111See Chart Item #12 Colored Rear Shroud 1 112See Chart Item #13 Colored Swing Arm Shroud 1 113See Chart Item #14 Colored Fender Shroud 1 114See Chart Item #15 Colored Front Shroud and Bracket

Assembly1 115

1119281-NLA NLA - Plate, Name, Patent Numbers 1 1161035900 Decal, Transportation 1 1171079203 Decal, Warning Pinch Point 1 2181168979 Kit, Shroud Bracket and Hardware - Right 1 119 B

Bracket, Shroud, Black - Right 1 120NLA - Fastener, Hook with Adhesive Back (1" W x2" L)

1 121Screw, Phillips Pan Head Tap (#10-32 x 3/8") 1 222

1168980 Kit, Shroud Bracket and Hardware - Left 1 119 BBracket, Shroud, Black - Left 1 120NLA - Fastener, Hook with Adhesive Back (1" W x2" L)


A - Includes items 2-5 B - Includes items 20-22

Item #6 Reflective Decal is not available for sale individually.

NOTE:



Item #12 Colored Rear Shroud

Description Wet Black (24P) Artic White (143P) Electric Silver(147P) Electric Red (61P) Electric Blue (62P)

1173518

1173517

1173516

1173515-NLA

1173514-NLA

Rear Shroud w/Decals, Elevate See Note(s) A See Note(s) A See Note(s) B, A See Note(s) A See Note(s) A

1173523

1173522

1173521-NLA

1173520

1173519

Rear Shroud w/Decals,

Non-Elevate See Note(s) A See Note(s) A See Note(s) B, A See Note(s) A See Note(s) AA - The Controller is also covered by the Rear Shroud. Shroud includes items 6, 15 and 16. B - As of 11/2/11 Silver Metallic (60P) was replaced with Electric Silver (147P). Wheelchairs manufactured before 11/2/11 mustorder the Electric Silver (147P) Shroud and Hardware Conversion Kit dated Before 7/11/11.

NOTE:

Item #13 Colored Swing Arm Shroud


1173498

1173497

1173496

1173495

1173494

Swing Arm Shroudw/ Decal - Right See Note(s) A See Note(s) A See Note(s) B, A See Note(s) A See Note(s) A

1173503

1173502

1173501

1173500

1173499

Swing Arm Shroudw/ Decal - Left See Note(s) A See Note(s) A See Note(s) B, A See Note(s) A See Note(s) A

A - Shroud includes item #7 Decal. B - As of 11/2/11 Silver Metallic (60P) was replaced with Electric Silver (147P). Wheelchairs manufactured before 11/2/11 mustorder the Electric Silver (147P) Shroud and Hardware Conversion Kit dated Before 7/11/11.

NOTE:

Item #14 Colored Fender Shroud


1173508

1173507

1173506

1173505-NLA

1173504

Fender Shroud w/Decal - Right See Note(s) A See Note(s) A See Note(s) B, A See Note(s) A See Note(s) A

1173513

1173512

1173511

1173510-NLA

1173509

Fender Shroud w/Decal - Left See Note(s) A See Note(s) A See Note(s) B, A See Note(s) A See Note(s) A

A - Shroud includes item #8 Decal only. Item #18 Decal is not included. B - As of 11/2/11 Silver Metallic (60P) was replaced with Electric Silver (147P). Wheelchairs manufactured before 11/2/11 mustorder the Electric Silver (147P) Shroud and Hardware Conversion Kit dated Before 7/11/11.

NOTE:



Item #15 Colored Front Shroud and Bracket Assembly


1173486

1173485

1173484

1173483-NLA

1173482-NLA

Front Shroud andBracket Assembly,

Elevate See Note(s) A See Note(s) A See Note(s) B, A See Note(s) A See Note(s) A1173493

1173492

1173491

1173490

1173489


Non-Elevate See Note(s) A See Note(s) A See Note(s) B, A See Note(s) A See Note(s) AA - Item #15 is sold as a complete assembly only. B - As of 11/2/11 Silver Metallic (60P) was replaced with Electric Silver (147P). Wheelchairs manufactured before 11/2/11 mustorder the Electric Silver (147P) Shroud and Hardware Conversion Kit dated Before 7/11/11.

NOTE:


Shrouds and Hardwarew/ Lights After 07/10/11





1168901-NLA NLA - Kit, Shrouds and Bezel Mounting Hardware 1 11 AScrew, Thumb w/ Shoulder (M9.5 x 24.13mm, M6 x1)

1 42Screw, Thumb (M5 x .8 x 12mm) 1 43Screw, Phillips Pan Head Tap (#10-32 x 3/8") 1 24Screw, Phillips Pan Head SEMS w/ Patch (M3 x .5 x10mm)

1 251167400-NLA NLA - Decal, FDX Model, Swing Arm 1 271168380-NLA NLA - Decal, Invacare Logo, Fender - Right 1 181168381-NLA NLA - Decal, Invacare Logo, Fender - Left 1 18

1174876 Kit, Tail Light and Bezel Assembly - Right 1 19 B1174875 Kit, Tail Light and Bezel Assembly - Left 1 19 B

60102804 Kit, Cover, Lighting Bezel Lens - Right 1 11060102805 Kit, Cover, Lighting Bezel Lens - Left 1 110See Chart Item #11 Colored Rear Shroud 1 111See Chart Item #12 Colored Swing Arm Shroud 1 112See Chart Item #13 Kit, Colored Fender Shroud w/ Decal and

Head Light Assembly1 113

See Chart Item #14 Colored Front Shroud and BracketAssembly

1 1141119281-NLA NLA - Plate, Name, Patent Numbers 1 115

1035900 Decal, Transportation 1 1161079203 Decal, Warning Pinch Point 1 2171174879 Kit, Head Light Assembly - Right/Left 1 118 C

Housing, Head Light, Black 1 119Bracket, Securing, Black 1 120Screw, Phillips Pan Head (#4-20 x 1/4") 1 221Bottom, Rubber 1 122Screw, Phillips Pan Head (#4-40 x 1/2") 1 323Washer, Plain (1/8 x 1/4 x 1/32") 1 324Light Assembly 1 125Instruction Sheet, Installation 1 1Power Wheelchair Wiring Guide 1 1

1168979 Kit, Shroud Bracket and Hardware - Right 1 126 DBracket, Shroud, Black - Right 1 127NLA - Fastener, Hook with Adhesive Back (1" W x2" L)


1168980 Kit, Shroud Bracket and Hardware - Left 1 126 DBracket, Shroud, Black - Left 1 127NLA - Fastener, Hook with Adhesive Back (1" W x2" L)


1174877-NLA NLA - Kit, Light Module Y-Cable Assembly 1 130 E



A - Includes items 2-5. B - Tail Lights and Bezel are Hardwired together and individual components are not available. Kit also includes (2) Tie Wraps,

Installation Instructions and Power Wheelchair Wiring Guide (not shown). C - Includes items 19-25, Installation Instructions and Power Wheelchair Wiring Guide (not shown). Individual components are

not available. D - Includes items 27-29. E - Includes the Light Module Y-Cable Assembly, (10) Tie Wraps, Installation Instructions and Power Wheelchair Wiring Guide

(not shown). Item #6 Reflective Decal is not available for sale individually.

NOTE:

Item #11 Colored Rear Shroud


1173518

1173517

1173516

1173515-NLA

1173514-NLA

Rear Shroud w/Decals, Elevate See Note(s) A See Note(s) A See Note(s) A, B See Note(s) A See Note(s) A

1173523

1173522

1173521-NLA

1173520

1173519

Rear Shroud w/Decals,

Non-Elevate See Note(s) A See Note(s) A See Note(s) B, A See Note(s) A See Note(s) AA - The Controller is also covered by the Rear Shroud. Shroud includes items 6, 15 and 16. B - As of 11/2/11 Silver Metallic (60P) was replaced with Electric Silver (147P). Wheelchairs manufactured before 11/2/11 mustorder the Electric Silver (147P) Shroud and Hardware Conversion Kit dated Before 7/11/11.

NOTE:

Item #12 Colored Swing Arm Shroud


1173498

1173497

1173496

1173495

1173494

Swing Arm Shroudw/ Decal - Right See Note(s) A See Note(s) A See Note(s) B, A See Note(s) A See Note(s) A

1173503

1173502

1173501

1173500

1173499

Swing Arm Shroudw/ Decal - Left See Note(s) A See Note(s) A See Note(s) B, A See Note(s) A See Note(s) A

A - Shroud includes item #7 Decal. B - As of 11/2/11 Silver Metallic (60P) was replaced with Electric Silver (147P). Wheelchairs manufactured before 11/2/11 mustorder the Electric Silver (147P) Shroud and Hardware Conversion Kit dated Before 7/11/11.

NOTE:



Item #13 Kit, Colored Fender Shroud w/ Decal and Head Light Assembly


1174884

1174883

1174882

1174881

1174880

Kit, Fender Shroudw/ Decal andHead Light

Assembly - Right See Note(s) A2, A1 See Note(s) A2, A1 See Note(s) B, A2, A1 See Note(s) A1, A2 See Note(s) A1, A2

1174889

1174888

1174887

1174886

1174885

Kit, Fender Shroudw/ Decal andHead Light

Assembly - Left See Note(s) A1, A2 See Note(s) A2, A1 See Note(s) A1, B, A2 See Note(s) A1, A2 See Note(s) A2, A1A1 - Fender Shroud includes item #8 Decal only. Item #17 Decal is not included. When a replacement Fender Shroud is requested,the Head Light Assembly will always be attached to the Fender Shroud also. Only the Head Light Assembly is sold separately as aKit. A2 - The Fender Shroud also contains the Head Light Connector Assembly that is hardwired to the shroud and is not soldseparately. Includes (2) Tie Wraps and Installation Instructions. B - As of 11/2/11 Silver Metallic (60P) was replaced with Electric Silver (147P). Wheelchairs manufactured before 11/2/11 mustorder the Electric Silver (147P) Shroud and Hardware Conversion Kit dated Before 7/11/11.

NOTE:

Item #14 Colored Front Shroud and Bracket Assembly


1173486

1173485

1173484

1173483-NLA

1173482-NLA


Elevate See Note(s) A See Note(s) A See Note(s) A, B See Note(s) A See Note(s) A1173493

1173492

1173491

1173490

1173489


Non-Elevate See Note(s) A See Note(s) A See Note(s) B, A See Note(s) A See Note(s) AA - Item #14 is sold as a complete assembly only. B - As of 11/2/11 Silver Metallic (60P) was replaced with Electric Silver (147P). Wheelchairs manufactured before 11/2/11 mustorder the Electric Silver (147P) Shroud and Hardware Conversion Kit dated Before 7/11/11.

NOTE:


Caster and Forks - RearNOTE: Rear Fork and Stem Caster Head Tube Cap is not used for the FDX model. The Swing Arm Shroud

covers over the Fork and Stem Caster Head Tube instead.


Caster and Forks - RearNOTE: Rear Fork and Stem Caster Head Tube Cap is not used for the FDX model. The Swing Arm Shroud

covers over the Fork and Stem Caster Head Tube instead.Item


Package Assembly1162570 Fork and Stem, 1-Sided - Right 1 111162571 Fork and Stem, 1-Sided - Left 1 111162534 Caster, Rear, Urethane (200mm x 60mm) 1 12 A1168904 Kit, Caster Mounting Hardware 1 13 B

NLA - Washer, Steel (10mm x 20mm x 2mm) 1 14NLA - Locknut (M10 x 1.5) 1 15NLA - Cap, End, Tube, Black (35mm) 1 16Spacer, Steel (5/8 x 7/8 x 1/8") 1 27

1168905 Package, Cap, End, Tube, Black (35mm) (Pair) 2 161168903 Kit, Fork Mounting Hardware 1 18 C

Locknut (M14 x 2) 1 19Washer, Nylon (5/8 x 1-5/16 x 1/8") 1 110Spacer, Stem (5/8 x 1-1/8 x 3/16") 1 111

40117X006 Bearing (5/8") 1 2121110717 Ring, Tolerance 1 213

A - Individual components are non-serviceable. If a custom needs to replace the (2) caster bearings, you must order a new Rear Caster part #1162534.

B - Includes items 4-7 C - Includes items 9-11

NOTE:


Drive Wheels and Mounting Hardware (14" x 3")


Drive Wheels and Mounting Hardware (14" x 3")Item


Package Assembly1167685 Drive Wheel Assembly, Flat Free Gel Foam, Grey

Tire/Silver Rim (14" x 3")1 11 A

1141342 Tire w/ Foam Fill Insert, Grey (14" x 3") 1 1D1168891 Kit, 4-Pole Motor Drive Wheel Mounting Hardware

(14" x 3")1 12 B

Screw, Socket Head w/ Patch (M8 x 1.25 x 25mm) 1 53Locknut (M12 x 1.5) 1 14Washer, Plain (12.38mm x 30mm x 2mm) 1 15Spacer, Hub (3mm) 1 16Hub, Wheel (14" x 3") 1 17Spacer, Hub (5mm) 1 18Key (6mm x 6mm x 40mm) 1 19

1168890 Kit, 2-Pole Motor Drive Wheel Mounting Hardware(14" x 3")

1 110 CScrew, Socket Head w/ Patch (M8 x 1.25 x 25mm) 1 53Locknut (M12 x 1.5) 1 14Washer, Plain (12.38mm x 30mm x 2mm) 1 15Hub, Wheel (14" x 3") 1 17Key (6mm x 6mm x 40mm) 1 19Spacer, Hub (8mm) 1 111

A - 14" x 3" Tire w/ Soft Density Flat Free Gel foam (yellow) is not available for item #1 part number 1167685. Customer can use the Tire w/ Hard Density Flat Free foam (green) part #1141342. It is recommended to order in pairs to match.

B - Includes items 3-9 C - Includes items 3-5, 7, 9 and 11 D - Not Shown. It is recommended to order in pairs to match foam density.

NOTE:


ADJASBA Seat Frame, Seat Pan and Hardware(12"-16" Wide)


ADJASBA Seat Frame, Seat Pan and Hardware(12"-16" Wide)



1163033-NLA NLA - Frame, Center Seat, Black 1 111126126-NLA NLA - Crossbar, Seat Frame (12 - 16" W) 1 42

1122647 Rail, Seat Frame (16 - 20" D For Formula TRE and16 - 19" D For ADJASBA)

1 231142961 Pan, Seat, with Hook and Loop Fasteners (12 - 16"

W x 12 - 18" D)1 14 A

1043082 Hook Fastener with Adhesive Back (2" W x 18" L) 1 251044580 Loop Fastener with Adhesive Back (2" W x 18" L) 1 251135501 Kit, Seat Frame Assembly Hardware 1 16 B

Screw, Hex Head w/ Patch (1/4-20 x 3/4") 1 87Washer (1/4 x 1/2 x 1/16") 1 28Spacer, Coved (1/4 x 11/16 x 1/2") 1 49Screw, Socket Button (1/4-20 x 3/4") 1 210NLA - Pin, Roll (3/16 x 1") 1 211

A - Includes item 5. B - Includes items 7-11.

NOTE:


ADJASBA/ADJRECL Seat Frame, Seat Pan and Hardware(16" - 20" Wide) x (16" - 22" Deep)





1163031 Frame, Center Seat, Black 1 11 D1122475 Crossbar, Seat Frame (16" - 20" W) 1 421122647 Rail, Seat Frame (16 - 20" D For Formula TRE and

16 - 19" D For ADJASBA)1 23

1122677 Rail, Seat Frame (20 - 22" D Formula TRE) (19 -22" D ADJASBA)

1 231124386 Pan, Seat with Hook and Loop Fasteners (16 - 20"

W) x (16 - 20" D For Formula TRE) & (16 - 19" DFor ADJASBA)

1 14

1124666 Pan, Seat, with Hook and Loop Fasteners (16 - 20"W) x (20 - 22" D For Formula TRE) & (19 - 22" DFor ADJASBA)

1 14

1043082 Hook Fastener with Adhesive Back (2" W x 18" L) 1 25 A1044580 Loop Fastener with Adhesive Back (2" W x 18" L) 1 25 A1043084 Hook Fastener with Adhesive back (2" W x 22" L) 1 25 B1044584 Loop Fastener with Adhesive back (2" W x 22" L) 1 25 B1135501 Kit, Seat Frame Assembly Hardware 1 16 C


1114823 Decal, Seat Adjustment Warning 1 212A - For 16" - 19" deep seats B - For 19" - 22" deep seats C - Includes items 7-11 D - When ordering a new Center Seat Frame, also order 2 ea. Seat Adjustment Warning Decals (Item #12).

NOTE:





1163031 Frame, Center Seat, Black 1 11 D1120283 Crossbar, Seat Frame (20" - 24" W) 1 42 E1122647 Rail, Seat Frame (16 - 20" D For Formula TRE and

16 - 19" D For ADJASBA)1 23

1122677 Rail, Seat Frame (20 - 22" D Formula TRE) (19 -22" D ADJASBA)

1 231124388 Pan, Seat, with Hook and Loop Fasteners (20 - 24"

W) x (16 - 20" D For Formula TRE) & (16 - 19" DFor ADJASBA)

1 14 E

1124667 Pan, Seat with Hook and Loop Fasteners (20 - 24"W) x (20 - 22" D For Formula TRE) & (19 - 22" DFor ADJASBA)

1 14 E

1043082 Hook Fastener with Adhesive Back (2" W x 18" L) 1 25 A1044580 Loop Fastener with Adhesive Back (2" W x 18" L) 1 25 A1043084 Hook Fastener with Adhesive back (2" W x 22" L) 1 25 B1044584 Loop Fastener with Adhesive back (2" W x 22" L) 1 25 B1135501 Kit, Seat Frame Assembly Hardware 1 16 C


1114823 Decal, Seat Adjustment Warning 1 212A - For 16" - 19" deep seats B - For 19" - 22" deep seats C - Includes items 7-11 D - When ordering a new Center Seat Frame, also order 2 ea. Seat Adjustment Warning Decals (Item #12). E - FDX model configuration goes up to 22" wide only.

NOTE:


ADJASBA Seat Frame Mounting Hardware Non-Elevate (12" - 22" Wide)



ADJASBA Seat Frame Mounting Hardware Non-Elevate (12" - 22" Wide)




1168899-NLA NLA - Kit, Seat Frame Mounting Hardware,Non-Elevate and Elevate

1 11 AScrew, Hex Head SEMS w/ Patch (5/16-18 x 3/4") 1 82NLA - Nut, Weld (5/16-18 x 1-1/8" Spacing) 1 43

1168898 Kit, Seat Post Mounting Hardware, Non-Elevate 1 14 BScrew, Hex Head w/ Patch (M8 x 1.25 x 20mm) 1 45NLA - Washer, Steel (8.4mm x 16mm x 1.6mm) 1 46Screw, Socket Head w/ Patch (M8 x 1.25 x 20mm) 1 47

A - Includes items 2 and 3. B - Includes items 5-7.

NOTE:


ADJASBA Seat Frame Mounting Hardware Elevate - CGE (12" - 22" Wide)



ADJASBA Seat Frame Mounting Hardware Elevate - CGE (12" - 22" Wide)




1168899-NLA NLA - Kit, Seat Frame Mounting Hardware,Non-Elevate and Elevate

1 11 AScrew, Hex Head SEMS w/ Patch (5/16-18 x 3/4") 1 82NLA - Nut, Weld (5/16-18 x 1-1/8" Spacing) 1 43

1065939-NLA NLA - Screw, Hex Head (3/8-16 x 1") 1 441028486 Locknut, Low Profile (3/8-16) 1 45

1163050-NLA NLA - Bracket, Seat Frame Elevate MountingBracket, Black - Right

1 161163051-NLA NLA - Bracket, Seat Frame Elevate Mounting

Bracket, Black - Left1 16

A - Includes items 2 and 3. Part # 1168899 Hardware can be used to mount the Center Seat Frame or the Right and Left side Seat Frame Elevate Mounting Brackets.

NOTE:


Seat Cushion Assembly, Curve Contoura

#1 Curve Contoura Seat Cushion AssemblyNOTE: To order a Mesh Contoura Seat Cushion Assembly, please use quote # SM-100908010838 when

placing your order.Chair Width 21" Deep 22" Deep16" Deep 17" Deep 18" Deep 19" Deep 20" Deep

N/AN/A1132986

1132985

1132984

1132983-NLA

1132982 16" Wide See Note(s) A See Note(s) A See Note(s) A See Note(s) A See Note(s) A

N/AN/A1132991

1132990

1132989

1132988-NLA

1132987 18" Wide See Note(s) A See Note(s) A See Note(s) A See Note(s) A See Note(s) A

1132998

1132997

1132996

1132995

1132994

1132993-NLA

1132992 20" Wide See Note(s) A See Note(s) A See Note(s) A See Note(s) A See Note(s) A See Note(s) A See Note(s) A

1133003

1133002

1133001

1133000

1132999 N/AN/A22" Wide See Note(s) A See Note(s) A See Note(s) A See Note(s) A See Note(s) A

A - Cushion Foam is not available separately. NOTE:


Seat Cushion Assembly, Curve Contoura#2 Curve Contoura Seat Cushion Cover Before 12/16/10

Chair Width 21" Deep 22" Deep16" Deep 17" Deep 18" Deep 19" Deep 20" DeepN/AN/A1132957-NLA1132956-NLA1132955-NLA1132954-NLA1132953-NLA16" WideN/AN/A1132962-NLA1132961-NLA1132960-NLA1132959-NLA1132958-NLA18" Wide

1132969-NLA1132968-NLA1132967-NLA1132966-NLA1132965-NLA1132964-NLA1132963-NLA20" Wide1132974-NLA1132973-NLA1132972-NLA1132971-NLA1132970-NLAN/AN/A22" Wide

Contoura Seat Cushion Covers listed on this chart are No Longer Available. Refer to the Contoura Seat Cushion Covers dated after 12/15/10as a direct replacement.


Seat Cushion Assembly, Curve Contoura#2 Curve Contoura Seat Cushion Cover After 12/15/10

Chair Width 21" Deep 22" Deep16" Deep 17" Deep 18" Deep 19" Deep 20" DeepN/AN/A1167376116737511673741167373-NLA116737216" WideN/AN/A1167381116738011673791167378-NLA116737718" Wide

116738811673871167386116738511673841167383-NLA116738220" Wide11673931167392116739111673901167389N/AN/A22" Wide

#2 Curve Contoura Seat Cushion Cover, Mesh (CTBMSH)

Chair Width 21" Deep 22" Deep16" Deep 17" Deep 18" Deep 19" Deep 20" DeepN/AN/A1164212116421111642101164209116420816" WideN/AN/A1164217116421611642151164214116421318" Wide

116422411642231164222116422111642201164219116421820" Wide11642291164228116422711642261164225N/AN/A22" Wide


Conventional Back without Mounting Hardware(12"-15" Wide)

NOTE: Hook Fastener Adhesive Kit must be ordered when a Back Pan is requested. This will allow theLoop Fastener Adhesive on the Back Cover to attach properly.




#1 Back Assembly without Hardware

OverallBack

HeightMaterial

BackHeight

12" Wide 13" Wide 14" Wide 15" Wide

114628411462791146274114626912"16"114628511462801146275114627013"17"114628611462811146276114627114"18"114628711462821146277114627215"19"114628811462831146278114627316"20"

#2 Back Pan without Hook Fastener Adhesive

OverallBack

HeightMaterial

BackHeight


114875411487491148744114873912"16"114875511487501148745114874013"17"114875611487511148746114874114"18"114875711487521148747114874215"19"114875811487531148748114874316"20"




#3 Back Cushion Assembly with Hook & Loop Fastener Adhesive

OverallBack

HeightMaterial

BackHeight


114877411487691148764114875912"16"114877511487701148765114876013"17"114877611487711148766114876114"18"114877711487721148767114876215"19"114877811487731148768114876316"20"

NOTE: Back Cover and Foam are sold as a Back Cushion Assembly only.



See Chart #1 Back Assembly without Hardware 1 11See Chart #2 Back Pan without Hook Fastener Adhesive 1 12See Chart #3 Back Cushion Assembly with Hook & Loop

Fastener Adhesive1 13

1125723 Kit, Hook Fastener w/ Adhesive Back 1 15 AA - Hook Fastener Adhesive kit is used for 12"-15" wide Conventional Backs to attach the Back Cover to the Back Pan and

must be ordered when a new Back Pan is requested. NOTE:


Curve Contoura Back w/o Mounting Hardware


Curve Contoura Back w/o Mounting HardwareLateral and Lumbar Supports



See Chart #1 Curved Contoura Back Kit 1 11 ASee Chart #1 Mesh Curved Contoura Back Kit (CTBMSH) 1 11 ASee Chart #3 Curve Contoura Back Cushion Assembly 1 13 BSee Chart #3 Mesh Curve Contoura Back Cushion Assembly

(CTBMSH)1 13 B

1166151 Kit, Lateral Support, Contoura Back (22" H) (Pair) 1 16 CScrew, Socket, Button (1/4-20 x 3/8") 1 4Support, Lateral (22" H) 1 2

1163130-NLA NLA - Kit, Lateral Support, Contoura Back (25" H)(Pair)

1 16 CScrew, Socket, Button (1/4-20 x 3/8") 1 47Support, Lateral (25" H) 1 28

1163131-NLA NLA - Kit, Lateral Support, Contoura Back (28" H)(Pair)

1 16 CScrew, Socket, Button (1/4-20 x 3/8") 1 47Support, Lateral (28" H) 1 28

1084410-NLA NLA - Support, Lumbar - Large 1 19A - Includes Items 2 thru 9. B - Includes Items 4 and 5. Back Cover and Foam are sold as a Back Cushion Assembly only. C - Included Items 7 and 8.

Item #2 is a non-saleable part. Refer to item #1 Kit when ordering.

NOTE:

#1 Curved Contoura Back Kit

Overall Back Height

Material Back Height


1165849

1165848

1165847

1165846 17" High22" High See Note(s) A See Note(s) A See Note(s) A See Note(s) A

1161486

1161484

1161482


1161487

1161485

1161483


A - Includes items 2-9 NOTE:Overall Back Height includes the spacing gap dimension from the bottom of the Back Assembly to the Seat Pan

#1 Mesh Curved Contoura Back Kit (CTBMSH)

Overall Back Height




Curve Contoura Back w/o Mounting Hardware#1 Mesh Curved Contoura Back Kit (CTBMSH)

Overall Back Height


16" Wide 18" Wide 20" Wide 22" Wide1165844

1165843

1165842

1165837

17" High22" High See Note(s) A See Note(s) A See Note(s) A See Note(s) A1164241

1164239

1164237

1164235

20" High25" High See Note(s) A See Note(s) A See Note(s) A See Note(s) A1164242

1164240

1164238

1164236

23" High28" High See Note(s) A See Note(s) A See Note(s) A See Note(s) AA - Includes items 2-9 NOTE:

Overall Back Height includes the spacing gap dimension from the bottom of the Back Assembly to the Seat Pan


Curve Contoura Back w/o Mounting Hardware#3 Curve Contoura Back Cushion Assembly

Overall Back Height



1166149

1166148

1166147

1166146 17" High22" High See Note(s) B See Note(s) B See Note(s) B See Note(s) B

1163254-NLA

1163252-NLA

1163250-NLA

1163248-NLA 20" High25" High See Note(s) B See Note(s) B See Note(s) B See Note(s) B

1163255-NLA

1163253-NLA

1163251-NLA

1163249-NLA 23" High28" High See Note(s) B See Note(s) B See Note(s) B See Note(s) B

B - Includes items 4 and 5. Back Cover and Foam are sold as a Back Cushion Assembly only. NOTE:Overall Back Height includes the spacing gap dimension from the bottom of the Back Assembly to the Seat Pan

#3 Mesh Curve Contoura Back Cushion Assembly (CTBMSH)

Overall BackHeight

Material BackHeight 16" Wide 18" Wide 20" Wide 22" Wide

1166144

1166143

1166142


1171648

1171646

1171644


1171649

1171647

1171645


B - Includes items 4 and 5. Back Cover and Foam are sold as a Back Cushion Assembly only. NOTE:Overall Back Height includes the spacing gap dimension from the bottom of the Back Assembly to the Seat Pan


Metal Curved Back Assembly(16" - 22" Wide)

NOTE: Curved Back mounts only to back canes without a 10 degree bend.



NOTE: Curved Back mounts only to back canes without a 10 degree bend.Hook Adhesive Kit and Trim Edge



See Chart #1 Back Pan w/ Vinyl Edge Trim 16" - 18" Wide 1 11See Chart #1 Back Pan w/ Vinyl Edge Trim 19" - 22" Wide 1 11See Chart #2 Back Cushion Assembly 16" - 18" Wide 1 12See Chart #2 Back Cushion Assembly 19" - 22" Wide 1 12See Chart #3 Back Assembly with Hardware 16" - 18" Wide 1 13See Chart #3 Back Assembly with Hardware 19" - 22" Wide 1 131125723 Kit, Hook Fastener w/ Adhesive Back 1 14 A

1125724-NLA NLA - Trim, Edge, Cut-To-Length, Vinyl Black (96"L)

1 15A - Hook Fastener Adhesive Kit is used to attach the Back Cover to the Back Pan and must be ordered when a new Back Pan

or Back Assembly is requested. NOTE:

#1 Back Pan w/ Vinyl Edge Trim - 16" - 18" Wide

OverallBack Height

Material Back Height 16" Wide 17" Wide 18" Wide

11578481157837115782611"16"11578491157838115782712"17"11578501157839115782813"18"11578511157840115782914"19"11578521157841115783015"20"11578531157842115783116"21"11578541157843115783217"22"11578551157844115783318"23"11578561157845115783419"24"

NOTE: Hook Fastener Adhesive Kit must be ordered when a Back Pan or Back Assembly is requested. This will allow the Loop FastenerAdhesive on the Back Cover to attach properly.



NOTE: Curved Back mounts only to back canes without a 10 degree bend.#1 Back Pan w/ Vinyl Edge Trim - 19" - 22" Wide

Overall Back Height

Material

Back Height 19" Wide 20" Wide 21" Wide 22" Wide

115789211578811157870115785911"16"115789311578821157871115786012"17"115789411578831157872115786113"18"115789511578841157873115786214"19"115789611578851157874115786315"20"115789711578861157875115786416"21"115789811578871157876115786517"22"115789911578881157877115786618"23"115790011578891157878115786719"24"


#2 Back Cushion Assembly - 16" - 18" Wide

Overall Back Height

MaterialBack Height

16" Wide 17" Wide 18" Wide

11602291160218116020712-1/2"16"11602301160219116020813-1/2"17"11602311160220116020914-1/2"18"11602321160221116021015-1/2"19"11602331160222116021116-1/2"20"11602341160223116021217-1/2"21"11602351160224116021318-1/2"22"11602361160225116021419-1/2"23"11602371160226116021520-1/2"24"

NOTE: Back cover and foam are sold as a Back Cushion Assembly only.



NOTE: Curved Back mounts only to back canes without a 10 degree bend.#2 Back Cushion Assembly - 19" - 22" Wide

OverallBack Height

MaterialBack Height 19" Wide 20" Wide 21" Wide 22" Wide

1097381-NLA1097380-NLA1097379-NLA1097378-NLA12-1/2"16"1097388-NLA1097387-NLA1097386-NLA1097385-NLA13-1/2"17"1097395-NLA1097394-NLA1097393109739214-1/2"18"

109740210974011097400109739915-1/2"19"109740910974081097407109740616-1/2"20"109741610974151097414109741317-1/2"21"109742310974221097421109742018-1/2"22"109743010974291097428109742719-1/2"23"109743710974361097435109743420-1/2"24"

NOTE: Back cover and foam are sold as a Back Cushion Assembly only.



NOTE: Curved Back mounts only to back canes without a 10 degree bend.#3 Back Assembly with Hardware - 16" - 18" Wide

OverallBack Height

Material BackHeight ABS Plastic

CurvedMaterial

Back HeightMetal Curved


110699311069831106973-NLA11"12"16"11069941106984110697412"13"17"11069951106985110697513"14"18"11069961106986110697614"15"19"11069971106987110697715"16"20"11069981106988110697816"17"21"11069991106989110697917"18"22"11070001106990110698018"19"23"11070011106991110698119"20"24"


#3 Back Assembly with Hardware - 19" - 22" Wide

OverallBack Height 22" Wide

Material BackHeight ABS

Plastic CurvedMaterial

Back HeightMetal Curved


110703311070231107013110700311"12"16"110703411070241107014110700412"13"17"110703511070251107015110700513"14"18"110703611070261107016110700614"15"19"

1107042-NLA11070271107017110700715"16"20"110704311070281107018110700816"17"21"110704411070291107019110700917"18"22"110704511070301107020110701018"19"23"110704611070311107021110701119"20"24"





1148440 Kit, Conventional Back Mounting Hardware (12"-15"Wide)

1 11 AScrew, Socket Button Head (1/4-20 x 1-1/2") 1 42NLA - Clamp, Inner 1 43NLA - Clamp, Outer 1 44Locknut (1/4-20) 1 45NLA - Pin, Hinge 1 46

A - Includes items 2-6 NOTE:

Conventional Back Mounting Hardware (12" - 15" W)


Curve Contoura Mounting Back Hardware


Curve Contoura Mounting Back HardwareItem


Package Assembly1157925 Kit, Metal Curved and Curve Contoura Back

Mounting Hardware1 11 A

Spacer, Back Pan, Black 1 42Hook, Back Assembly Mounting 1 43Screw, Socket Button Head (1/4-20 x 1") 1 44Washer (1/4 x 23/32 x 1/16") 1 85NLA - Screw, Phillips Oval Head (#10-16 x 7/8") 1 26Locknut (1/4-20) 1 47

A - Includes Items 2 thru 7. NOTE:




1157925 Kit, Metal Curved and Curve Contoura BackMounting Hardware

1 11 AScrew, Socket Button Head (1/4-20 x 1") 1 42Washer (1/4 x 23/32 x 1/16") 1 83Spacer, Back Pan, Black 1 44Hook, Back Assembly Mounting 1 45NLA - Screw, Phillips Oval Head (#10-16 x 7/8") 1 26Locknut (1/4-20) 1 47


Back Mounting HardwareMetal Curved (16" - 22" Wide)


Recliner Back AssemblyFor ADJRECL Seat Frames





1027095 Plug Button, Black (7/8") 1 211052997-NLA NLA - Headrest Tube Assembly, Black - Right 1 121052998-NLA NLA - Headrest Tube Assembly, Black - Left 1 12

See Chart #3 Back Cane with Grip 1 131050214 Cable with Trigger 1 24 B1050215 Cable with Trigger 1 24 C1050216 Cable with Trigger 1 24 D1026032 Washer, Nylon (11/32 x 11/16 x 1/16") 1 451050153 Screw, Shoulder Hex Socket Head (5/16 x 7/8",

1/4-20)1 26

1050154 Cylinder, Lock, Recline 1 27 E1050306 Cylinder, Lock 1 27 F1050136 Pivot, Block 1 281012371 Washer, Nylon (3/8 x 7/8 x 1/16") 1 1291031665 Screw, Shoulder Hex Socket Head (3/8 x 1-1/2",

5/16-18)1 410

1050293 Bar, Spreader, Black (14-20" W) 1 111 G1050294 Bar, Spreader, Black (21-24" W) 1 111 H1024713 Spring, Torsion w/ Button 1 212

1091417-NLA NLA - Screw, Phillips Pan Head (#10-24 x 1-1/4") 1 2131095503-NLA NLA - Package, Tie Wrap (5-5/8" L) 10 114

1025736 Locknut (1/4-20) 1 2151026907 Washer (1/4 x 1/2 x 1/16") 1 2161026158 Locknut (5/16-18) 1 4171025704 Washer, Flat (5/16 x 5/8 x 1/16") 1 4181134498 Kit, Limit Switch Assembly 1 119 A

NLA - Screw, Slotted Hex Washer Head Tap(#4-3/8")

1 520NLA - Washer, Internal Tooth Lock (#4-40) 1 521Sensor, Actuator Switch 1 122NLA - Clamp, Cable 1 123

1144926 Cable, Drive Lockout Sensor, MK6i 1 124A - Includes items 20-23. Cable sensor is not included, see item 24 B - 26" high back canes C - 22-24" high back canes D - 18-20" high back canes E - 250 lb. weight limit F - 251-300 lb. weight limit G - 16-17" wide H - 18-22" wide

NOTE:

#3 Back Cane with Grip



#3 Back Cane with Grip

Back Height 16" - 17" Wide Rt. 16" - 17" Wide Lt. 18" - 22" Wide Rt. 18" - 22" Wide Lt.105209010520891052080105207918" H105209210520911052082105208120" H105209410520931052084105208322" H105209610520951052086105208524" H105209810520971052088105208726" H


Back Upholstery - Nylon



1026298 Package, Screw with Washer (#10 x 7/8") (Pair) 2 1ASee Chart Single Liners 1 1See Chart Dual Liners - Nylon 1 1

A - Not Shown NOTE:

Single Liners

Width 21" - 22" High 23" - 24" High12" - 13"

High14" - 15"

High16" - 17"

High18" - 19"

High20" High

N/AN/AN/A1045258-NLA1045257-NLA1045222-NLA1045221-NLA12" WideN/AN/AN/A1045260-NLA1045259-NLA1045224-NLA1045223-NLA13" WideN/AN/A10689451045205104517310499421049939-NLA14" WideN/AN/A1068946104520610451741049943-NLA1049940-NLA15" Wide

1054529104515910689471045207104517510499441049941-NLA16" Wide105453010451601068948104520810451761049945N/A17" Wide105453110451611068949104520910451771049946N/A18" Wide


Back Upholstery - Nylon

Dual Liners

Width 16" - 17" High

18" - 19" High

20" High

21" - 22" High

23" - 24" HighN/AN/A10689501045210104517814" WideN/AN/A10689511045211104517915" Wide

1054534104516410689521045212104518016" Wide1054535104516510689531045213104518117" Wide1054536104516610689541045214104518218" Wide1054537104516710689551045215104518319" Wide1054538104516810689561045216104518420" Wide1054539104516910689571045217104518521" Wide1054540104517010689581045218104518622" Wide

NOTE: Dual liner back upholstery is used with chairs that have a seat deeper than 17" or back wider than 18".


Back Upholstery - NylonRecliner



1027059 Package, Back Upholstery Screws w/ Washers (#10x 7/8")

10 1ASee Chart Single Liners 1 1See Chart Dual Liners 1 1

A - Not Shown NOTE:

Single LinersWidth 18" High 20" High 22" High 24" High 26" High

1050334105032910503241050319105031416" Wide1050335-NLA105033010503251050320105031517" Wide

1050336105033110503261050321105031618" Wide

Dual LinersWidth 18" High 20" High 22" High 24" High 26" High

1050383105037210503611050350105033916" Wide1050384105037310503621050351105034017" Wide1050385105037410503631050352105034118" Wide1050386105037510503641050353105034219" Wide1050387105037610503651050354105034320" Wide1050388105037710503661050355105034421" Wide1050389105037810503671050356105034522" Wide


Back Upholstery - NylonRecliner

NOTE: Dual liner back upholstery is used with chairs that have a seat deeper than 17" or back wider than 18".




1030441 Package, Headrest Upholstery, Screws w/ Washers(#10 x 7/8")

6 6ASee Chart Nylon Headrest 1 1ASee Chart Headrest Pillows - Nylon 1 1A

A - Not Shown NOTE:

Nylon Headrest

Chair Width Part Number105462816" Wide

1055281-NLA17" Wide1054629-NLA18" Wide1055282-NLA19" Wide

105528320" Wide1055284-NLA21" Wide1055285-NLA22" Wide

Headrest material height measures 10" High

Headrest Pillows - Nylon

Chair Width 16" - 18" Wide 19" - 22" Wide10545981054896Part Number

Headrest Upholstery and PillowsRecliner


Back Cane, Spreader Bar and Push Handle Assembly(12"-16" W) Sling Nylon Back Uph. (12"-15" W) Conv. Back





1126147 Kit, Spreader Bar Assembly (12"-16" Wide) 1 11 A,BCover, Spreader Bar (16-20" W) 1 12NLA - Insert, Spreader Bar Connector, Black 1 23Anti-Rattle (1") 1 24Screw, Socket Button Head (1/4-20 x 1-1/2") 1 45Spacer, Coved (1/4 x 11/16 x 1/2") 1 46NLA - Tube, Spreader Bar, Black 1 17Locknut (1/4-20) 1 28Plug Button, Black (1") 1 29

1152733 Kit, Back Cane Assembly with Hardware (12"-15"Back Height) - Right

1 110 CGrip, Hand, Foam (4") 1 111Handle, Push, Black 1 112Cane, Back, Lower, Black - Right (12-15" H) 1 113Screw, Socket Head (1/4-20 x 1-1/4") 1 214Locknut (1/4-20) 1 215

1152734 Kit, Back Cane Assembly with Hardware (12"-15"Back Height) - Left

1 110 CGrip, Hand, Foam (4") 1 111Handle, Push, Black 1 112Cane, Back, Lower, Black - Left (12-15" H) 1 113Screw, Socket Head (1/4-20 x 1-1/4") 1 214Locknut (1/4-20) 1 215


1 110 CGrip, Hand, Foam (4") 1 111Handle, Push, Black 1 112Cane, Back, Lower, Black - Right (16-19" H) 1 113Screw, Socket Head (1/4-20 x 1-1/4") 1 214Locknut (1/4-20) 1 215


1 110 CGrip, Hand, Foam (4") 1 111Handle, Push, Black 1 112Cane, Back, Lower, Black - Left (16-19" H) 1 113Screw, Socket Head (1/4-20 x 1-1/4") 1 214Locknut (1/4-20) 1 215


1 110 CGrip, Hand, Foam (4") 1 111Handle, Push, Black 1 112Cane, Back, Lower, Black - Right (20 - 22" H) 1 113Screw, Socket Head (1/4-20 x 1-1/4") 1 214Locknut (1/4-20) 1 215






1 110 CGrip, Hand, Foam (4") 1 111Handle, Push, Black 1 112Cane, Back, Lower, Black - Left (20 - 22" H) 1 113Screw, Socket Head (1/4-20 x 1-1/4") 1 214Locknut (1/4-20) 1 215

1135505 Package, Foam Hand Grip (4" L) 10 111A - Plug Buttons are not required when stroller handles are used. B - Includes items 2-9 C - Includes items 11-15

NOTE:


Back Canes and Spreader BarsFor ADJASBA Seats (16" - 22" W)

Curve Contoura, Metal Curved Backs for ADJASBA Seating do not utilize a Spreader Bar Assembly.



Curve Contoura, Metal Curved Backs for ADJASBA Seating do not utilize a Spreader Bar Assembly.Item


Package AssemblySee Chart #1 Back Cane Assemblies 1 111135506 Package, Foam Hand Grip (9" L) 10 121134426 Package, Plug Button, Black (3/4") 10 131125709 Kit, Spreader Bar Assembly (16"-20" Wide) 1 14 A

NLA - Handle, Spreader Bar, Black 1 25Screw, Hex Head (1/4-20 x 1-1/2") 1 26Spacer, Coved (1/4 x 11/16 x 1/2") 1 47Anti-Rattle (1") 1 28Tube, Spreader Bar, Adjustable, Black (16 - 20" W) 1 19Locknut (1/4-20) 1 210

1125710 Kit, Spreader Bar Assembly 20"-24" Wide 1 14 ANLA - Handle, Spreader Bar, Black 1 25Screw, Hex Head (1/4-20 x 1-1/2") 1 26Spacer, Coved (1/4 x 11/16 x 1/2") 1 47Anti-Rattle (1") 1 28Tube, Spreader Bar, Adjustable, Black (20 - 24" W) 1 19Locknut (1/4-20) 1 210

1025730 Locknut (5/16-24) 1 2111031026 Screw w/ Lug (5/16-24 x 1-3/8") 1 212


#1 Back Cane Assemblies

BackHeight

(SECT)Back Cane-Push Handle10 Deg. Bend

Left

(9720P)Back Cane-

No PushHandle

10 Deg. BendRight

(9720P)Back Cane-

No PushHandle

10 Deg. BendLeft

(SRUP)Back Cane-Push Handle

StraightRight


StraightLeft


Right1133815-NLA1133814-NLA113378611337851134059113405812" High1133817-NLA1133816-NLA113378811337871134061113406013" High1133819-NLA1133818-NLA113379011337891134063113406214" High1133821-NLA1133820-NLA113379211337911134065113406415" High

11338231133822113379411337931134067113406616" High11338251133824113379611337951134069113406817" High113382711338261143335

1143334

1134071113407018" High See Note(s) B See Note(s) B11338291133828113380011337991134073113407219" High113383111338301133802

1133801

1134075113407420" High See Note(s) C See Note(s) C See Note(s) C

113383311338321136012

1136011 1134077113407621" High See Note(s) A See Note(s) A



Curve Contoura, Metal Curved Backs for ADJASBA Seating do not utilize a Spreader Bar Assembly.

#1 Back Cane Assemblies

BackHeight


Left

(9720P)Back Cane-

No PushHandle

10 Deg. BendRight

(9720P)Back Cane-

No PushHandle

10 Deg. BendLeft


StraightRight


StraightLeft


Right

11338351133834113601411360131134079113407822" High113383811338371136016

1136015

1134081113408023" High See Note(s) A See Note(s) A113384011338391136018

1136017

1134083113408224" High See Note(s) A See Note(s) AN/AN/A1160329

1160328

N/AN/A25" High See Note(s) A See Note(s) AN/AN/A1160331

1160330

N/AN/A26" High See Note(s) A See Note(s) AA - 21"-26" High Straight Back Canes with Push Handles are only offered On-Chair when the Back Upholstery is omitted B - Wheelchairs with a Curved Contoura Back 22" high wll use the 18" high Straight Back Cane w/ Push Handle. C - Wheelchairs with a (Curve Contoura Back 25" or 28" high) or (Metal Curved Back 20"-26" high) will use the 20" high StraightCane w/ Push Handle.

NOTE:

NOTE: Back Cane Assemblies include Foam Grips and Plug Buttons where shown


Back Cane Mounting Hardware(12"-16" Wide) ADJASBA Seats

"T"- Arms are used for 12" - 16" Wide and 12" - 18" Deep wheelchairs with TRRO Option and withoutTRRO Option.


Back Cane Mounting Hardware(12"-16" Wide) ADJASBA Seats

"T"- Arms are used for 12" - 16" Wide and 12" - 18" Deep wheelchairs with TRRO Option and withoutTRRO Option.



1146452-NLA NLA - Bracket, Back Cane Mounting, Black 1 111154110 Kit, Back Cane Bracket Mounting Hardware 1 12 A

T-Nut (5/16-18) 1 23Washer, Steel (5/16 x 3/4 x 1/16") 1 24Screw, Hex Head w/ Patch (5/16-18 x 3/4") 1 25

1147973 Kit, Back Cane Mounting Hardware (Pair) 1 16 BNLA - Insert, Back Cane 1 27Washer, Flat (21/64 x 53/64 x 7/64") 1 48Screw, Hex Head (5/16-18 x 1") 1 29NLA - Screw, Hex Head (5/16-18 x 2") 1 210Locknut (5/16-18) 1 411Washer, Flat (5/16 x 5/8 x 1/16") 1 212Spacer, Coved (3/4 x 1 x 1/2") 1 213

1154111-NLA NLA - Kit, Back Cane Bracket Mounting HardwareTRRO

1 114 CT-Nut (5/16-18) 1 115Washer, Steel (5/16 x 3/4 x 1/16") 1 216NLA - Screw, Hex Head w/ Patch (5/16-18 x 1") 1 117Screw, Socket Head (5/16-18 x 3/4") 1 118Screw, Hex Head w/ Patch (5/16-18 x 3/4") 1 119

1147968 Kit, Back Cane Mounting Hardware TRRO (Pair) 1 120 DNLA - Insert, Back Cane 1 221Bolt, Round Head Square Neck (5/16-18 x 1") 1 222Screw, Round Head Square Neck (5/16-18 x 2") 1 223Locknut (5/16-18) 1 224Washer, Flat (5/16 x 5/8 x 1/16") 1 225Spacer, Coved (3/4 x 1 x 1/2") 1 226Locknut (5/16-18) 1 227Washer, Flat (21/64 x 53/64 x 7/64") 1 228

A - Includes items 3-5 B - Includes items 7-13 C - Includes items 15-19 D - Includes items 21-28

NOTE:


Back Cane Mounting HardwareFor Nylon Upholstery (16" - 22" Wide)


Back Cane Mounting HardwareFor Nylon Upholstery (16" - 22" Wide)



1133755 Kit, Back Cane Mounting Hardware (Pair) 1 11 AScrew, Hex Head (5/16-18 x 1") 1 42Washer, Flat (21/64 x 53/64 x 7/64") 1 43Locknut (5/16-18) 1 44Locknut (5/16-24) 1 25Screw w/ Lug (5/16-24 x 1-3/8") 1 26



Back Cane Mounting HardwareFor Nylon Upholstery (16" - 22" Wide) TRRO Option


Back Cane Mounting HardwareFor Nylon Upholstery (16" - 22" Wide) TRRO Option



1137234-NLA NLA - Kit, Back Cane Mounting Hardware ForTRRO Option (Pair)

1 11 AWasher, Flat (21/64 x 53/64 x 7/64") 1 42Bolt, Round Head Square Neck (5/16-18 x 1-1/4") 1 23Bolt, Round Head Square Neck (5/16-18 x 1") 1 24Locknut (5/16-18) 1 45Screw w/ Lug (5/16-24 x 1-3/8") 1 26Locknut (5/16-24) 1 27

A - Includes items 2-7, Right and Left sides NOTE:


Back Cane Mounting HardwareMetal Curved Back, Curve Contoura, BPO Option (16" - 22" Wide)


Back Cane Mounting HardwareMetal Curved Back, Curve Contoura, BPO Option (16" - 22" Wide)



1135999 Kit, Back Cane Mounting Hardware (Pair) 1 11 AScrew, Hex Head (5/16-18 x 1") 1 42Washer, Flat (21/64 x 53/64 x 7/64") 1 43Locknut (5/16-18) 1 44

A - Includes items 2-4. Used for Curve Contoura, Metal Curved Back or BPO Option models NOTE:


Arms, "T" and Hardware"T"- Arms are used for 12" - 16" Wide and 12" - 18" Deep wheelchairs with TRRO Option and without

TRRO Option.


Arms, "T" and Hardware"T"- Arms are used for 12" - 16" Wide and 12" - 18" Deep wheelchairs with TRRO Option and without

TRRO Option.Item


Package Assembly8881083213 Pad, Arm, Desk Length - Right (9" L x 2" W) 1 11 A8881083214 Pad, Arm, Desk Length - Left (9" L x 2" W) 1 11 A8881083215 Pad, Arm, Full Length - Right (14" L x 2" W) 1 11 A8881083216 Pad, Arm, Full Length - Left (14" L x 2" W) 1 11 A

1055205 Package, Screw Phillips Pan Head (#10-32 x 1-3/8") 2 121069639 T-Arm Assembly w/ Plug Buttons, Desk Length, Low

Range, Black1 13

1069643 T-Arm Assembly w/ Plug Buttons, Full Length, LowRange, Black

1 131027095 Plug Button, Black (7/8") 1 241069635 Post, Arm, Low Range 1 151073424 Kit, Clothing Guard, Low Range - Right 1 161073425 Kit, Clothing Guard, Low Range - Left 1 161069652 Guard, Clothing, Low Range 1 171069634 Tube, Support, Low Range, Black - Right 1 18

1073247-NLA NLA - Tube, Support, Low Range, Black - Left 1 181028427 Grip, Foam 1 191025731 Locknut (#10-32) 1 1101076839 Lever, Locking 1 1111025716 Screw, Phillips Pan Head (#10-32 x 11/16") 1 112

1073196-NLA NLA - Spring, Torsion 1 1131006773-NLA NLA - Screw, Socket Button Head (1/4-20 x 1/2") 1 4141075069-NLA NLA - Clamp, Clothing Guard - Right 1 1151075070-NLA NLA - Clamp, Clothing Guard - Left 1 115

1151356 Kit, "T" Arm Socket Mounting Hardware 1 116 BBracket, "T" Arm Socket 1 117Insert, Arm Socket, Black 1 218NLA - Bracket, Socket, Black 1 119NLA - Screw, Socket Button Head (1/4-28 x 3/4") 1 420Lockwasher (1/4 x 15/32 x 1/64") 1 421

1098960 Screw, Socket Head w/ Patch (5/16-18 x 5/8") 1 2221069724 T-Nut (5/16-18) 1 223

A - Specify U67 upholstery color when ordering. B - Includes items 17-21

NOTE:


Arms, Adjustable Height(12"-16" W x 12"-15" D)

Chairs 12" - 15" Deep with TRRO Option must use "T"-Arms. All Non-TRRO Option chairs 12" - 15" Deepuse the Adjustable Height Arms.


Arms, Adjustable Height(12"-16" W x 12"-15" D)

Chairs 12" - 15" Deep with TRRO Option must use "T"-Arms. All Non-TRRO Option chairs 12" - 15" Deepuse the Adjustable Height Arms.



8881015932 Pad, Arm, Vinyl, Full Length - Right (14" L x 2" W) 1 11 A8881015933 Pad, Arm, Vinyl, Full Length - Left (14" L x 2" W) 1 11 A8881053577 Kit, Arm Pad w/ Screws, Full Length (14" L x 2" W)

(Pair)1 11 A

8881011811 Pad, Arm, Vinyl, Desk Length (9" L x 2" W) 1 11 A8881053578 Kit, Arm Pad w/ Screws, Desk Length (9" L x 2" W)

(Pair)1 11 A

1071263 Arm Tube Assembly w/ Plug Buttons, Full Length,Black - Right/Left

1 121071259 Arm Tube Assembly w/ Plug Buttons, Desk Length,

Black - Right/Left1 12

1027095 Plug Button, Black (7/8") 1 231055949 Package, Screw, Phillips Pan Head (#10-32 x

1-3/8")2 14

47471X074 Spring, Arm Lock 1 151028594 Pin, Arm Lock, Black 1 161090768 Kit, Lock Handle w/Rivets (Pair) 1 171065936 Plug, Pivot 1 281067734 Plug Button, Black (5/8") 1 291016298 Grip, Push Handle 1 1101068585 Arm Base Assembly, Adjustable Height, Black -

Right1 111 B

1068586 Arm Base Assembly, Adjustable Height, Black - Left 1 111 BA - Specify U67 Black upholstery color when ordering. B - Includes items 5-10

NOTE:


Adjustable Height Arms(12" - 16" Wide x 16" - 18" Deep) and (16" - 22" Wide x 16" - 22" Deep) Seat

FramesChairs 16" - 18" Deep models with TRRO Option use the Adjustable Height Arms. All Non-TRRO Option

chairs 16" - 22" Deep also use the Adjustable Height Arms.


Adjustable Height Arms(12" - 16" Wide x 16" - 18" Deep) and (16" - 22" Wide x 16" - 22" Deep) Seat

FramesChairs 16" - 18" Deep models with TRRO Option use the Adjustable Height Arms. All Non-TRRO Option

chairs 16" - 22" Deep also use the Adjustable Height Arms.Item


Package Assembly1117328 Kit, Arm Pad w/ Screws, Full Length, Urethane

Waterfall, Black (13" L x 2-5/8" W)

1 11

1110818 Kit, Arm Pad w/ Screws, Full Length, UrethaneWaterfall, Black (13" L x 2-5/8" W) (Pair)

1 111117327 Kit, Arm Pad w/ Screws, Desk Length, Urethane


1 11

1110817 Kit, Arm Pad w/ Screws, Desk Length, UrethaneWaterfall, Black (9" L x 2-5/8" W) (Pair)

1 111071253 Arm Tube Assembly w/ Plug Buttons, Full Length,

Black - Right/Left1 12

1070859 Arm Tube Assembly w/ Plug Buttons, Desk Length,Black - Right/Left

1 121027095 Plug Button, Black (7/8") 1 231094270 Package, Screw, Phillips Pan Head (#10-32 x

1-1/4")2 14

1064130 Guard, Clothing 1 1547471X074 Spring, Arm Lock 1 16

1028594 Pin, Arm Lock, Black 1 171032244 Grip, Foam Hand (9" L) 1 181090768 Kit, Lock Handle w/Rivets (Pair) 1 191028645 Rivet 1 6101065936 Plug, Pivot 1 2111067734 Plug Button, Black (5/8") 1 2121068416 Arm Base Assembly, Black - Right (16-19" D) 1 113 A,B1068417 Arm Base Assembly, Black - Left (16-19" D) 1 113 A,B1067761 Arm Base Assembly, 1" Lower, Black - Right

(16-19" D)1 113 A,B

1067762 Arm Base Assembly, 1" Lower, Black - Left (16-19"D)

1 113 A,B1035065 Cover, Clothing Guard w/ Pocket, FXDESK &

ADJFULL/ADJDESK1 114

A - Includes items 5-12 B - All seat depths will use the 16" - 19" deep replacement components only.

NOTE:


Fixed Height Arms(16" - 22" Wide x 16" - 22" Deep)


Fixed Height Arms(16" - 22" Wide x 16" - 22" Deep)



See Chart #1 Arms Less Pad - 16" - 22" Deep Seat Frames 1 11 A1117328 Kit, Arm Pad w/ Screws, Full Length, Urethane


1 12

1110818 Kit, Arm Pad w/ Screws, Full Length, UrethaneWaterfall, Black (13" L x 2-5/8" W) (Pair)

1 121117327 Kit, Arm Pad w/ Screws, Desk Length, Urethane


1 12

1110817 Kit, Arm Pad w/ Screws, Desk Length, UrethaneWaterfall, Black (9" L x 2-5/8" W) (Pair)

1 121068564 Tube, Arm, Desk Length, Black - Right (16-19" D) 1 13 B

1068565-NLA NLA - Tube, Arm, Desk Length, Black - Left (16-19"D)

1 13 B1068490 Tube, Arm, Full Length, Black - Right (16-19"D) 1 13 B

1068491-NLA NLA - Tube, Arm, Full Length, Black - Left (16 -19"D)

1 13 B1032244 Grip, Foam Hand (9" L) 1 141025729 Screw, Phillips Pan Head Tap (#8-32 x 3/8") 1 45

1035472-NLA NLA - Guard, Clothing, Desk Length 1 16 B1044572-NLA NLA - Guard, Clothing, Full Length (16 - 19" D) 1 16 B

1035065 Cover, Clothing Guard w/ Pocket, FXDESK &ADJFULL/ADJDESK

1 171094270 Package, Screw, Phillips Pan Head (#10-32 x

1-1/4")2 18

1065936 Plug, Pivot 1 291067734 Plug Button, Black (5/8") 1 210

A - Includes items 3-6 & 9-10 B - All seat depths will use the 16-19" deep replacement components only.

NOTE:

#1 Arms Less Pad

16" - 22" Deep Seat FramesArm Style Right Left

1068567-NLA1068566-NLADesk Length1068560-NLA1068559-NLAFull Length


Arm Mounting Swingaway Hardware


Arm Mounting Swingaway HardwareItem


Package Assembly1068488 Kit, Swingaway Armrest Mounting Hardware 1 11 A1019590 Screw, Socket Button Head (1/4-20 x 1-5/8") 1 121068025 Clevis, Pivot 1 131025195 Locknut (1/4-20) 1 141068039 Pin, Pull 1 15



Front/Rear Arm Socket Assembly and Hardware(12" - 16" Wide x 12" - 18" Deep)

Refer to page titled "Back Cane Mounting Hardware For ADJASBA Seats (12" - 16" Wide)" for replacingthe Back Cane Bracket for chairs with T-Arms



Refer to page titled "Back Cane Mounting Hardware For ADJASBA Seats (12" - 16" Wide)" for replacingthe Back Cane Bracket for chairs with T-Arms



1144596 Kit, Front/Rear Arm Socket Asbly. Mtg. Hdwr.(12-16" Wide)

1 11 AScrew, Hex Head w/ Patch (5/16-18 x 5/8") 1 42Washer, Steel (5/16 x 3/4 x 1/16") 1 43T-Nut (5/16-18) 1 44

1144596 Kit, Front/Rear Arm Socket Asbly. Mtg. Hdwr.(12-16" Wide)

1 15 BScrew, Hex Head w/ Patch (5/16-18 x 5/8") 1 46Washer, Steel (5/16 x 3/4 x 1/16") 1 47T-Nut (5/16-18) 1 48

1136025-NLA NLA - Kit, Front/Rear Arm Socket AssemblyMounting Hardware For TRRO Option

1 19 CScrew, Hex Head w/ Patch (5/16-18 x 3/4") 1 110NLA - Screw, Hex Head w/ Patch (5/16-18 x 1") 1 111Screw, Socket Head (5/16-18 x 3/4") 1 112Washer, Steel (5/16 x 3/4 x 1/16") 1 413T-Nut (5/16-18) 1 114T-Nut (5/16-18) 1 215Screw, Hex Head w/ Patch (5/16-18 x 5/8") 1 216

1122619 Socket, Arm, Front - Right 1 1171122620 Socket, Arm, Front - Left 1 1171126142 Socket, Arm, Rear 1 1181125478 Bracket, Arm Socket/Cane, Rear - Right 1 1191125479 Bracket, Arm Socket/Cane, Rear - Left 1 119

A - Includes items 2-4. Used for (12"-15" Deep). B - Includes items 6-8. Used for (16"-18" Deep). C - Includes items 10-16. Used for TRRO option (16"-18" Deep).

NOTE:





1125734 Kit, Front/Rear Arm Socket Assembly MountingHardware

1 11 AScrew, Hex Head w/ Patch (5/16-18 x 3/4") 1 22Washer, Steel (5/16 x 3/4 x 1/16") 1 43T-Nut (5/16-18) 1 44Screw, Hex Head w/ Patch (5/16-18 x 5/8") 1 25

1122619 Socket, Arm, Front - Right 1 161122620 Socket, Arm, Front - Left 1 161125478 Bracket, Arm Socket/Cane, Rear - Right 1 171125479 Bracket, Arm Socket/Cane, Rear - Left 1 171134481 Socket, Arm, ADJRECL, Rear - Right 1 171134482 Socket, Arm, ADJRECL, Rear - Left 1 17



Front/Rear Arm Socket Assembly and Hardware(16" - 22" W x 16" - 22" D) TRRO Option



Front/Rear Arm Socket Assembly and Hardware(16" - 22" W x 16" - 22" D) TRRO Option




1136025-NLA NLA - Kit, Front/Rear Arm Socket AssemblyMounting Hardware For TRRO Option

1 11 AScrew, Hex Head w/ Patch (5/16-18 x 3/4") 1 12NLA - Screw, Hex Head w/ Patch (5/16-18 x 1") 1 13Screw, Socket Head (5/16-18 x 3/4") 1 14Washer, Steel (5/16 x 3/4 x 1/16") 1 45T-Nut (5/16-18) 1 16T-Nut (5/16-18) 1 27Screw, Hex Head w/ Patch (5/16-18 x 5/8") 1 28

1122619 Socket, Arm, Front - Right 1 191122620 Socket, Arm, Front - Left 1 19

A - Includes items 2-8. NOTE:


Cantilever Arms


Cantilever Arms Item


Package Assembly1161126 Cantilever Arm Hardware, Full Length - Right 1 11 A1161127 Cantilever Arm Hardware, Full Length - Left 1 11 A1161128 Cantilever Arm Hardware, Desk Length - Right 1 11 A1161129 Cantilever Arm Hardware, Desk Length - Left 1 11 A1161235 Pivot, Black 1 121160902 Bearing, Flange 1 231161232 Clamp, Black 1 141161233 Clamp, Block, Black 1 151162791 Tab, Stop, Black 1 161162515 Bushing, Pivot Arm 1 17

1162804-NLA NLA - Screw, Socket Head w/ Patch (1/2-13 x3-3/4")

1 181113438-NLA NLA - 3Screw, Socket Head (#10-32 x 1/2") 1 191161708-NLA NLA - Screw, Socket Button Head (10-32 x 1/4") 1 2101114962-NLA NLA - Screw, Socket Head (5/16-18 x 1") 1 3111025342-NLA NLA - Screw, Button Head (1/4-20 x 5/8") 1 112

0028202 Tube, Extension, Full Length 1 1131107155 Screw, Phillips Pan Head Tap (#10-32 x 1-1/4") 1 2141028755 Screw, Phillips Pan Head (#10-32 x 5/8") 1 1151160904 Tube, Arm, Waterfall - Right 1 1161160905 Tube, Arm, Waterfall - Left 1 1161161701 Tube, Arm, Recline - Right 1 1161161702 Tube, Arm, Recline - Left 1 1161082910 Pad, Arm w/ Elbow Stop, Desk Length, Urethane,

Black - Right (13" L x 3" W)1 117

1082911 Pad, Arm w/ Elbow Stop, Desk Length, Urethane,Black - Left (13" L x 3" W)

1 1171082912 Pad, Arm w/ Elbow Stop, Full Length, Urethane,

Black - Right (17" L x 3" W) 1 117

1082913 Pad, Arm w/ Elbow Stop, Full Length, Urethane,Black - Left (17" L x 3" W)

1 1171161557 Cantilever Spreader Arm Assembly (16 - 20" W) 1 118 B1161558 Cantilever Spreader Arm Assembly (20 - 24" W) 1 118 B1120280 Tube, Spreader Bar, Adjustable, Black (16 - 20" W) 1 1191120281 Tube, Spreader Bar, Adjustable, Black (20 - 24" W) 1 119

15680X013 Anti-Rattle (1") 1 2201025195 Locknut (1/4-20) 1 2211026099 Spacer, Coved (1/4 x 11/16 x 1/2") 1 4221030949 Screw, Hex Head (1/4-20 x 1-1/2") 1 2231127158 Cover, Spreader Bar (16-20" W) 1 1241161930 Cover, Spreader Bar (20-24" W) 1 1241161972 Cantilever Arm Assembly w/ Arm Pad, Full Length -

Right1 125 C

1161973 Cantilever Arm Assembly w/ Arm Pad, Full Length -Left

1 125 C


Cantilever Arms Item


Package Assembly1161976 Cantilever Arm Assembly w/ Arm Pad, Desk Length

- Right1 125 H

1161977 Cantilever Arm Assembly w/ Arm Pad, Desk Length- Left

1 125 H1027095 Plug Button, Black (7/8") 1 126See Note See Footnote 1 127 I1090190 Kit, Arm Pad w/ Screws and Elbow Stop, Desk

Length, Urethane, Black (13" L x 3" W) (Pair) 1 128 D

1090191 Kit, Arm Pad w/ Screws and Elbow Stop, FullLength, Urethane, Black (17" L x 3" W) (Pair)

1 128 D1117327 Kit, Arm Pad w/ Screws, Desk Length, Urethane


1 129 E

1117328 Kit, Arm Pad w/ Screws, Full Length, UrethaneWaterfall, Black (13" L x 2-5/8" W)

1 129 E

1161974 Cantilever Arm Assembly w/ Arm Pad, Recline, FullLength - Right

1 130 F1161975 Cantilever Arm Assembly w/ Arm Pad, Recline, Full

Length - Left1 130 F

1161978 Cantilever Arm Assembly w/ Arm Pad, Recline,Desk Length - Right

1 130 G1161979 Cantilever Arm Assembly w/ Arm Pad, Recline,

Desk Length - Left1 130 G

A - Includes items 2-12. B - Includes items 19-24. C - Includes items 13-16, 26 and 27. D - Includes items 14 and 17. E - Includes items 14 and 27. F - Includes items 13-17 and 26. G - Includes items 14, 16, 17 and 26. H - Includes items 14, 16, 26 and 27. I - Part not sold separately. See item 29.

NOTE:


MK6i Electronics


Center Mount Front Rigging (CTMT-FJ/CTMT-F)


Center Mount Front Rigging (CTMT-FJ/CTMT-F) Item


Package Assembly1121990 Kit, Center Mount Front Rigging, Junior

(CTMTJ/CTMT-FJ) ASBA/ADJASBA (9-1/2" - 11"Range)

1 11 A

Rack, Center Mount Rigging Angle Adjustable 1 12Support, Footrest, Center Mount, Black - Short 1 13Bearing, Flange (1/2 x 13/16 x 1/2") 1 24Cleat, Button Head 1 25Screw, Socket, Button Head w/ Patch (5/16-18 x3/4")

1 66Tube, Extension, Footrest, Short, Black - Right 1 17Tube, Extension, Footrest, Short, Black - Left 1 17Screw, Shoulder Hex Socket Head (5/16" x 2-1/2",1/4-20)

1 18Washer (1/4 x 1/2 x 1/16") 1 19Locknut (1/4-20) 1 110NLA - Washer, Wave (17/32 x 3/4 x 1/64") 1 211Screw, Socket Button Head (1/4-20 x 1-1/2") 1 212Washer, Nylon (5/16 x 11/16 x 1/16") 1 213Washer (1/2 x 7/8 x 3/64") 1 214Spacer, Nylon (1/2 x 3/4 x 1/4") 1 815

1117262 Kit, Center Mount Front Rigging (CTMT) (CTMT-F),ASBA/ADJASBA (11" - 15" Range)

1 11 ARack, Center Mount Rigging Angle Adjustable 1 12Support, Footrest, Center Mount, Black - Regular 1 13Bearing, Flange (1/2 x 13/16 x 1/2") 1 24Cleat, Button Head 1 25Screw, Socket, Button Head w/ Patch (5/16-18 x3/4")

1 66Tube, Extension, Footrest, Medium, Black - Right 1 17Tube, Extension, Footrest, Medium, Black - Left 1 17Screw, Shoulder Hex Socket Head (5/16" x 2-1/2",1/4-20)


1117263 Kit, Center Mount Front Rigging (CTMT-L)(CTMT-FL), ASBA/ADJASBA (14" - 18" Range)

1 11 ARack, Center Mount Rigging Angle Adjustable 1 12Support, Footrest, Center Mount, Black - Regular 1 13Bearing, Flange (1/2 x 13/16 x 1/2") 1 24Cleat, Button Head 1 25




Package AssemblyScrew, Socket, Button Head w/ Patch (5/16-18 x3/4")

1 66Tube, Extension, Footrest, Long, Black - Right 1 17Tube, Extension, Footrest, Long, Black - Left 1 17Screw, Shoulder Hex Socket Head (5/16" x 2-1/2",1/4-20)


1161428 Kit, Center Mount Front Rigging w/Calf Pad - Short(CTMTJ/CTMT-FJ) ASBA/ADJASBA (9-1/2" - 11"Range)

1 116 B

Rack, Center Mount Rigging Angle Adjustable 1 12Support, Footrest, Center Mount, Black - Short 1 13Bearing, Flange (1/2 x 13/16 x 1/2") 1 24Cleat, Button Head 1 25Screw, Socket, Button Head w/ Patch (5/16-18 x3/4")

1 66Tube, Extension, Footrest, Short, Black - Right 1 17Tube, Extension, Footrest, Short, Black - Left 1 17Screw, Shoulder Hex Socket Head (5/16" x 3",1/4-20)

1 18Washer (1/4 x 1/2 x 1/16") 1 19Locknut (1/4-20) 1 110NLA - Washer, Wave (17/32 x 3/4 x 1/64") 1 211Screw, Socket Button Head (1/4-20 x 1-1/2") 1 212Washer, Nylon (5/16 x 11/16 x 1/16") 1 213Washer (1/2 x 7/8 x 3/64") 1 214Spacer, Nylon (1/2 x 3/4 x 1/4") 1 815Screw, Socket Button Head w/ Patch (1/4-20 x 3/4") 1 617Washer, Nylon (5/16 x 7/8 x 1/8") 1 218Bracket, Calf Pad, Black 1 119Nut, T (5/16-18) 1 220Adjuster, Calf Pad 1 221Bracket, Mounting, Calf Pad 1 222Locknut (1/4-20) 1 223Screw, Socket, Button Head w/ Patch (5/16-18 x1/2")

1 224Pad, Calf (4-1/2" W x 7-1/4" L) 1 225




Package Assembly1161429 Kit, Center Mount Front Rigging w/Calf Pad -

Medium(CTMT) (CTMT-F), ASBA/ADJASBA (11" - 15"Range)

1 116 B

Rack, Center Mount Rigging Angle Adjustable 1 12Support, Footrest, Center Mount, Black - Regular 1 13Bearing, Flange (1/2 x 13/16 x 1/2") 1 24Cleat, Button Head 1 25Screw, Socket, Button Head w/ Patch (5/16-18 x3/4")

1 66Tube, Extension, Footrest, Medium, Black - Right 1 17Tube, Extension, Footrest, Medium, Black - Left 1 17Screw, Shoulder Hex Socket Head (5/16" x 3",1/4-20)

1 18Washer (1/4 x 1/2 x 1/16") 1 19Locknut (1/4-20) 1 110NLA - Washer, Wave (17/32 x 3/4 x 1/64") 1 211Screw, Socket Button Head (1/4-20 x 1-1/2") 1 212Washer, Nylon (5/16 x 11/16 x 1/16") 1 213Washer (1/2 x 7/8 x 3/64") 1 214Spacer, Nylon (1/2 x 3/4 x 1/4") 1 815Screw, Socket Button Head w/ Patch (1/4-20 x 3/4") 1 617Washer, Nylon (5/16 x 7/8 x 1/8") 1 218Bracket, Calf Pad, Black 1 119Nut, T (5/16-18) 1 220Adjuster, Calf Pad 1 221Bracket, Mounting, Calf Pad 1 222Locknut (1/4-20) 1 223Screw, Socket, Button Head w/ Patch (5/16-18 x1/2")

1 224Pad, Calf (4-1/2" W x 7-1/4" L) 1 225

1161430 Kit, Center Mount Front Rigging w/Calf Pad - Long (CTMT-L) (CTMT-FL), ASBA/ADJASBA (14" - 18"Range)

1 116 B

Rack, Center Mount Rigging Angle Adjustable 1 12Support, Footrest, Center Mount, Black - Regular 1 13Bearing, Flange (1/2 x 13/16 x 1/2") 1 24Cleat, Button Head 1 25Screw, Socket, Button Head w/ Patch (5/16-18 x3/4")

1 66Tube, Extension, Footrest, Long, Black - Right 1 17Tube, Extension, Footrest, Long, Black - Left 1 17Screw, Shoulder Hex Socket Head (5/16" x 3",1/4-20)

1 18Washer (1/4 x 1/2 x 1/16") 1 19




Package AssemblyLocknut (1/4-20) 1 110NLA - Washer, Wave (17/32 x 3/4 x 1/64") 1 211Screw, Socket Button Head (1/4-20 x 1-1/2") 1 212Washer, Nylon (5/16 x 11/16 x 1/16") 1 213Washer (1/2 x 7/8 x 3/64") 1 214Spacer, Nylon (1/2 x 3/4 x 1/4") 1 815Screw, Socket Button Head w/ Patch (1/4-20 x 3/4") 1 617Washer, Nylon (5/16 x 7/8 x 1/8") 1 218Bracket, Calf Pad, Black 1 119Nut, T (5/16-18) 1 220Adjuster, Calf Pad 1 221Bracket, Mounting, Calf Pad 1 222Locknut (1/4-20) 1 223Screw, Socket, Button Head w/ Patch (5/16-18 x1/2")

1 224Pad, Calf (4-1/2" W x 7-1/4" L) 1 225

See Chart #26 Extension Tube Kits Before 12/15/10 1 126 GSee Chart #26 Extension Tube Kits After 12/14/10 1 126See Chart #27 Footplate Kits Before 12/15/10 1 127 GSee Chart #27 Footplate Kits After 12/14/10 1 1271163373 Kit, Calf Pad (Pair) 1 130 C

Screw, Socket Button Head w/ Patch (1/4-20 x 3/4") 1 417Pad, Calf (4-1/2" W x 7-1/4" L) 1 225

1163374 Kit, Footrest Pad - Small (Pair) 1 131 DPad, Footplate, Small - Right 1 129Pad, Footplate, Small - Left 1 129

1163375 Kit, Footrest Pad - Medium (Pair) 1 131 DPad, Footplate, Medium - Right 1 129Pad, Footplate, Medium - Left 1 129

1163376 Kit, Footrest Pad - Large (Pair) 1 131 DPad, Footplate, Large - Right 1 129Pad, Footplate, Large - Left 1 129

1165505 Kit, Hardware, Calf Pad Adjustment 1 1EScrew, Socket Button Head w/ Patch (1/4-20 x 3/4") 1 217Nut, T (5/16-18) 1 220Adjuster, Calf Pad 1 221Bracket, Mounting, Calf Pad 1 222Locknut (1/4-20) 1 223Screw, Socket, Button Head w/ Patch (5/16-18 x1/2")

1 2241165506 Kit, Bracket, Calf Pad Mounting w/ Hardware 1 1F

Screw, Shoulder Hex Socket Head (5/16" x 3",1/4-20)

1 18Washer (1/4 x 1/2 x 1/16") 1 19




Package AssemblyLocknut (1/4-20) 1 110Washer, Nylon (5/16 x 7/8 x 1/8") 1 218Bracket, Calf Pad, Black 1 119

A - Includes items 2-15. As of 12/15/10 item #1 was revised to accommodate adjustable width footplate hardware. If footplates are needed see item #27.

B - Includes items 2-15 and 17-25. As of 12/15/10 item #16 was revised to accommodate adjustable width footplate hardware. If footplates are needed see item #27.

C - Includes items 17 and 25. D - Includes a pair of item 29. E - Not shown. Includes items 17 and 20-24. F - Not shown. Includes items 8-10, 18 and 19. G - Chairs built before 12/15/10 will require items 26 and 27 in order to convert to the new CTMT Front Rigging design.

NOTE:


Center Mount Front Rigging (CTMT-FJ/CTMT-F) #26 Extension Tube Kits Before 12/15/10

Front Rigging Side Short9-1/2" - 11" Range

Medium11" - 15" Range

Long14" - 18" Range1169821-NLA

1161986

1161984

Right See Note(s) A See Note(s) A See Note(s) A1169822-NLA

1161987

1161985

Left See Note(s) A See Note(s) A See Note(s) AA - Includes items 5-7. The Extension Tube Kits are used for non-adjustable width footplate hardware only. NOTE:

#26 Extension Tube Kits After 12/14/10

Front Rigging Side Short9-1/2" - 11" Range

Medium11" - 15" Range

Long14" - 18" Range

1170681

1170679

1170677 Right See Note(s) A See Note(s) A See Note(s) A

1170682

1170680

1170678 Left See Note(s) A See Note(s) A See Note(s) A

A - Includes items 5-7. The Extension Tube Kits are used for adjustable width footplate hardware only. NOTE:


Center Mount Front Rigging (CTMT-FJ/CTMT-F) #27 Footplate Kits Before 12/15/10

Footplate Side Small5-1/4" W x 7-1/2" L

Medium5-1/2" W x 9-1/2" L

Large5-7/8" W x 11-1/2" L

1161992

1161990


1161993

1161991


A - Includes items 10-13 and 16-18. The footplate mounting hardware included is for non-adjustable width only. NOTE:

#27 Footplate Kits After 12/14/10

Footplate Side Small5-1/4" W x 7-1/2" L

Medium5-1/2" W x 9-1/2" L

Large5-7/8" W x 11-1/2" L

1170687

1170685


1170688

1170686


A - Includes items 10-18 and the Adjustable Width Footplate Instruction Sheet (Not Shown). The footplate mounting hardwareincluded is for adjustable width only.

NOTE:


Center Mount Rigging (CTMT-F with CTMTFB One PCFlip-Up Footboard)

(CTMT-F = 11" - 15" Range)



(CTMT-F = 11" - 15" Range)Item


Package Assembly1165388 Center Mount Front Rigging w/ One PC Footboard

(11" - 15" Range)1 11 A

Rack, Center Mount Rigging Angle Adjustable 1 12Support, Footrest, Center Mount, Black - Regular 1 13Bearing, Flange (1/2 x 13/16 x 1/2") 1 24Screw, Shoulder Hex Socket Head (5/16" x 2-1/2",1/4-20)

1 15Washer (1/4 x 1/2 x 1/16") 1 16Locknut (1/4-20) 1 17Bracket, Heel Stop, Black 1 28NLA - Screw, Hex Head (5/16-18 x 3-1/4") 1 29Locknut (5/16-18) 1 210Footboard Extension Assembly, Black (11" - 15"Range)

1 111Plug Button, Black (1" Square) 1 112Screw, Socket, Button Head w/ Patch (5/16-18 x3/4")

1 413Cleat, Button Head 1 214Screw, Socket Head (3/8-16 x 2-1/2") 1 115Washer, Flat (3/8 x 11/16 x 1/16") 1 116Washer, Nylon (3/8 x 3/4 x 1/16") 1 217Bushing (3/8 x 5/8 x 1/2") 1 118Locknut, Low Profile (3/8-16) 1 119Screw, Set Socket Flat Point (5/16-18 x 1") 1 120Locknut (5/16-18) 1 121Footboard w/ Cover (11-1/4" W x 11-1/2" L) 1 122

1165389 Center Mount Front Rigging w/ One PC Footboard& Calf Pads (11" - 15" Range)

1 123 BRack, Center Mount Rigging Angle Adjustable 1 12Support, Footrest, Center Mount, Black - Regular 1 13Bearing, Flange (1/2 x 13/16 x 1/2") 1 24Screw, Shoulder Hex Socket Head (5/16" x 3",1/4-20)

1 15Washer (1/4 x 1/2 x 1/16") 1 16Locknut (1/4-20) 1 17Bracket, Heel Stop, Black 1 28NLA - Screw, Hex Head (5/16-18 x 3") 1 29Locknut (5/16-18) 1 210Footboard Extension Assembly, Black (11" - 15"Range)


1 413





Package AssemblyCleat, Button Head 1 214Screw, Socket Head (3/8-16 x 2-1/2") 1 115Washer, Flat (3/8 x 11/16 x 1/16") 1 116Washer, Nylon (3/8 x 3/4 x 1/16") 1 217Bushing (3/8 x 5/8 x 1/2") 1 118Locknut, Low Profile (3/8-16) 1 119Screw, Set Socket Flat Point (5/16-18 x 1") 1 120Locknut (5/16-18) 1 121Footboard w/ Cover (11-1/4" W x 11-1/2" L) 1 122Washer, Nylon (5/16 x 7/8 x 1/8") 1 224Bracket, Calf Pad, Black 1 125Screw, Socket Button Head w/ Patch (1/4-20 x 3/4") 1 626Nut, T (5/16-18) 1 227Adjuster, Calf Pad 1 228Bracket, Mounting, Calf Pad 1 229Locknut (1/4-20) 1 230Screw, Socket, Button Head w/ Patch (5/16-18 x1/2")

1 231Pad, Calf (4-1/2" W x 7-1/4" L) 1 232

1166067 Kit, Footboard Extension Assembly (11" - 15"Range)

1 133 CFootboard Extension Assembly, Black (11" - 15"Range)


1 413Cleat, Button Head 1 214

1147134 Kit, Footboard Mounting Hardware 1 134 DScrew, Socket Head (3/8-16 x 2-1/2") 1 115Washer, Flat (3/8 x 11/16 x 1/16") 1 116Washer, Nylon (3/8 x 3/4 x 1/16") 1 217Bushing (3/8 x 5/8 x 1/2") 1 118Locknut, Low Profile (3/8-16) 1 119Screw, Set Socket Flat Point (5/16-18 x 1") 1 120Locknut (5/16-18) 1 121

1114311 Footboard w/ Cover (11-1/4" W x 11-1/2" L) 1 1221163373 Kit, Calf Pad (Pair) 1 135 E

Pad, Calf (4-1/2" W x 7-1/4" L) 1 226Screw, Socket Button Head w/ Patch (1/4-20 x 3/4") 1 432

1165506 Kit, Bracket, Calf Pad Mounting w/ Hardware 1 1FScrew, Shoulder Hex Socket Head (5/16" x 3",1/4-20)

1 15Washer (1/4 x 1/2 x 1/16") 1 16





Package AssemblyLocknut (1/4-20) 1 17Washer, Nylon (5/16 x 7/8 x 1/8") 1 224Bracket, Calf Pad, Black 1 125

1165505 Kit, Hardware, Calf Pad Adjustment 1 1GScrew, Socket Button Head w/ Patch (1/4-20 x 3/4") 1 226Nut, T (5/16-18) 1 227Adjuster, Calf Pad 1 228Bracket, Mounting, Calf Pad 1 229Locknut (1/4-20) 1 230Screw, Socket, Button Head w/ Patch (5/16-18 x1/2")

1 231A - Includes items 2-22 B - Includes items 2-22 and 24-32 C - Includes items 11-14 D - Includes items 15-21 E - Includes items 26 and 32 F - Not shown. Includes items 5-7, 24 and 25 G - Not shown. Includes items 26-31

NOTE:


Center Mount Rigging Mounting Hardware (CTMT-F/CTMT-FJ)

(12" - 22" Wide) Chairs with ADJASBA Seats


Center Mount Rigging Mounting Hardware (CTMT-F/CTMT-FJ)

(12" - 22" Wide) Chairs with ADJASBA Seats Item


Package Assembly1168548 Kit, CTMT-F/CTMT-FL/CTMT-FJ Center Mount

Riggings Mounting Hardware1 11 A

Tie Wrap (11-1/2" L) 1 22Screw, Hex Head w/ Patch (5/16-18 x 5/8") 1 43Spacer (5/16 x 7/16 x 3/8") 1 24Block, Threaded 1 25Screw, Socket Head Cap w/ Patch (1/4-20 x 1-1/2") 1 46Spacer (1/4 x 3/8 x 29/32") 1 47Cap, End, Side Rail, Black 1 28Plug Button, Black (1") 1 29T-Nut (5/16-18) 1 110NLA - Screw, Socket Head (#10-32 x 1/2") 1 111Bracket, Release Handle Mounting, Black 1 112NLA - Screw, Hex Head w/ Patch (5/16-18 x 1/2") 1 113Nut, Square (#10-32) 1 114NLA - Pin, Quick Release (5" Long) 1 116Locknut (1/4-20) 1 117Screw, Shoulder Hex Socket Head (5/16" x 1-5/8",1/4-20)

1 118Cable/Brake Assembly 1 120Screw, Phillips Pan Head (#10-32 x 11/16") 1 221NLA - Washer, Lock (3/16 x 5/16 x 1/32") 1 222Housing, Ratchet 1 123Bearing, Glide 1 224Screw, Socket Button Head (1/4-20 x 1-1/2") 1 125Locknut (1/4-20) 1 126

1163027 Support, Center Mount Rigging, Black (12" - 19" D) 1 1151163029 Support, Center Mount Rigging, Long, Black (19" -

22" D)1 115

1121079 Cable/Brake Assembly w/ Ratchet Housing andGlide Bearing

1 119 B1113622 Cable/Brake Assembly 1 120

40163X008 Screw, Phillips Pan Head (#10-32 x 11/16") 1 2211028527-NLA NLA - Washer, Lock (3/16 x 5/16 x 1/32") 1 222

1113389 Housing, Ratchet 1 1231113383 Bearing, Glide 1 224

A - Includes items 2-14, 16-18 and 20-26 B - Includes items 20-24

NOTE:


Center Mount Rigging w/ Adductors Mounting Hardware (CTMT-F/CTMT-FJ)

(12" - 22" Wide) Chairs with ADJASBA Seats


Center Mount Rigging w/ Adductors Mounting Hardware (CTMT-F/CTMT-FJ)

(12" - 22" Wide) Chairs with ADJASBA Seats Item


Package Assembly1169214-NLA NLA - Kit, CTMT-F/CTMT-FL/CTMT-FJ Center

Mount Riggings w/ Adductors Mounting Hardware1 11 A

Tie Wrap (11-1/2" L) 1 22Screw, Hex Head w/ Patch (5/16-18 x 5/8") 1 43Spacer (5/16 x 7/16 x 3/8") 1 24Block, Threaded 1 25Screw, Socket Head Cap w/ Patch (1/4-20 x 1-1/2") 1 46Plug, Support 1 27Screw, Socket Button Head (1/4-20 x 1-1/2") 1 18T-Nut (5/16-18) 1 19NLA - Screw, Socket Head (#10-32 x 1/2") 1 110Bracket, Release Handle Mounting, Black 1 111NLA - Screw, Hex Head w/ Patch (5/16-18 x 1/2") 1 112Nut, Square (#10-32) 1 113NLA - Pin, Quick Release (5" Long) 1 114Locknut (1/4-20) 1 115Screw, Shoulder Hex Socket Head (5/16" x 1-5/8",1/4-20)

1 116Cable/Brake Assembly 1 118Screw, Phillips Pan Head (#10-32 x 11/16") 1 219NLA - Washer, Lock (3/16 x 5/16 x 1/32") 1 220Housing, Ratchet 1 121Bearing, Glide 1 222

1121079 Cable/Brake Assembly w/ Ratchet Housing andGlide Bearing

1 117 B1113622 Cable/Brake Assembly 1 118

40163X008 Screw, Phillips Pan Head (#10-32 x 11/16") 1 2191028527-NLA NLA - Washer, Lock (3/16 x 5/16 x 1/32") 1 220

1113389 Housing, Ratchet 1 1211113383 Bearing, Glide 1 2221163027 Support, Center Mount Rigging, Black (12" - 19" D) 1 1231163029 Support, Center Mount Rigging, Long, Black (19" -

22" D)1 123

A - Includes items 2-16 and 18-22. B - Includes items 18-22.

NOTE:


Oxygen Holder Assembly KitNOTE: Oxygen holder is not available on recliner options and the 12" - 16" wide ADJASBA Seat Frame


Oxygen Holder Assembly KitNOTE: Oxygen holder is not available on recliner options and the 12" - 16" wide ADJASBA Seat FrameItem


Package Assembly1135504 Kit, Oxygen Holder Assembly For ADJASBA Seats 1 11 A

Holder, Oxygen 1 12Bracket, Oxygen Holder (ASBA and ADJASBASeats)

1 13Screw, Hex Head w/ Patch (1/4-20 x 3/4") 1 44Washer (1/4 x 1/2 x 1/16") 1 45Locknut (1/4-20) 1 46Screw, Hex Head w/ Patch (5/16-18 x 1-1/4") 1 27Washer, Flat (21/64 x 53/64 x 7/64") 1 28Locknut (5/16-18) 1 29Instruction Sheet, Oxygen Holder For ADJASBASeats

1 110NLA - Bag, Poly Zip-Lip (8-3/4" L x 6" W) 1 111NLA - Bag, Poly (26" L x 15" W) 1 112NLA - Carton, Shipper 1 113



Compact Vent AssemblyNOTE: When ordering a Compact Vent Assembly for first time installation in the field, call Invacare

Corporation at 1-800-333-6900. Request Customer Service to review and reference "SPECIAL QUOTE#SM-091118102342" to ensure that all additional parts (not shown) and installation instruction sheet are

shipped. Wheelchair serial number is required. Components shown are for wheelchairs originally orderedwith a compact vent and solid back.







1162939 Compact Vent Assembly 1 11 A1154127 NLA - Kit, Compact Vent Mounting Hardware (14 -

16" Wide)1 12 B

Screw, Socket Button Head (1/4-20 x 5/8") 1 23Screw, Hex Head (1/4-20 x 1-5/8") 1 24Locknut (1/4-20) 1 45Washer (1/4 x 23/32 x 1/16") 1 26Spacer, Coved (1/4 x 11/16 x 1/2") 1 47Anti-Rattle (1") 1 28Tube, Spreader Bar, Adjustable (14 - 16" W) 1 19Handle, Spreader Bar (14 - 16" W) 1 210Bracket, Compact Vent Mounting, Black 1 111Compact Vent Mounting Strap Assembly andHardware (Pair)

2 1121154128 NLA - Kit, Compact Vent Mounting Hardware (16 -

20" Wide)1 12 C

Screw, Socket Button Head (1/4-20 x 5/8") 1 23Screw, Hex Head (1/4-20 x 1-5/8") 1 24Locknut (1/4-20) 1 25Washer (1/4 x 23/32 x 1/16") 1 26Spacer, Coved (1/4 x 11/16 x 1/2") 1 47Anti-Rattle (1") 1 28Tube, Spreader Bar, Adjustable, Black (16 - 20" W) 1 19Handle, Spreader Bar (16 - 20" W) 1 210Bracket, Compact Vent Mounting, Black 1 111Compact Vent Mounting Strap Assembly andHardware (Pair)

2 1121025730 Locknut (5/16-24) 1 2131031026 Screw w/ Lug (5/16-24 x 1-3/8") 1 214

1160743-NLA NLA - Back Cane Assembly, w/ Short Grip, w/o 10Degree Bend, Black - Right (18" H)

1 115 D1160744-NLA NLA - Back Cane Assembly, w/ Short Grip, w/o 10

Degree Bend, Black - Left (18" H)1 115 D

1086460 Grip, Foam, Hand (4-1/2" L) 1 1161134426 Package, Plug Button, Black (3/4") 10 117

1154288-NLA NLA - Instruction Sheet, Compact Vent AssemblyInstallation

1 1E





A - The Compact Vent Assembly is sold complete. individual components are non-serviceable B - Includes items 3-12 and used for 14" - 16" wide chairs C - Includes items 3-12 and used for 16" - 20" wide chairs D - Includes the Back Cane and items 16 and 17. The 18" High Back Cane Assembly with short grip is used when a Compact

Vent Assembly is ordered E - Not Shown

NOTE: When item #2 Compact Vent Mounting Hardware kit is required for 20" - 22" wide chairs, order as a "SPECIAL" order.

NOTE:


Adductors


AdductorsItem


Package Assembly1164876 Kit, Universal Stealth Adductor w/ Hardware Retrofit

(4" W x 4" H) (Pair)1 11 A

NLA - Adductor w/ Hardware (4" W x 4" H) (Pair) 1 12Screw, Socket Head Cap w/ Patch (1/4-20 x 1-1/2") 1 43Plug, Support 1 24

1164877 Kit, Universal Stealth Adductor w/ Hardware Retrofit(4" W x 6" H) (Pair)

1 11 ANLA - Adductor w/ Hardware (4" W x 6" H) (Pair) 1 12Screw, Socket Head Cap w/ Patch (1/4-20 x 1-1/2") 1 43Plug, Support 1 24

A - Includes items 2-4. Not all hardware will be used for all configuations. Parts maybe necessary depending on product configuation.

NOTE:


Miscellaneous Accessories

NOTE: Chest Positioning Straps share the same hardware that attaches a Back Upholstery



NOTE: Chest Positioning Straps share the same hardware that attaches a Back UpholsteryItem


Package AssemblySee Chart #1 Auto Style Push Button Positioning Strap 1 11See Chart #1 Airline Style Positioning Strap 1 11See Chart #1 Hook and Loop Style Positioning Strap 1 11See Chart #1 Pelvic Restraint Belt w/ Auto Style Buckle (TRRO

Option Only)1 11 A

1124385 Kit, Seat Positioning Strap Mounting Hardware (bothLT & RT sides)

1 12 BScrew, Hex Head w/ Patch (1/4-20 x 3/4") 1 23Washer (1/4 x 1/2 x 1/16") 1 24Locknut (1/4-20) 1 25

1134055-NLA NLA - Screw, Hex Head (3/8-24 x 5/8") 1 261134054-NLA NLA - Bushing, Nylon (1/2 x 9/16 x 9/32") 1 271134056-NLA NLA - Nut, Barrel (3/8-24) 1 2840176X010 Pump, Tire 1 1C

A - Before ordering a replacement Pelvic Restraint Belt for TRRO Option, Please read the information provided on page titled "TRRO and TRBKTS Option Clarification Reference" page

B - Includes items 3-5 C - Not Shown

NOTE:

#1 Auto Style Push Button Positioning Strap

Chair Width Part Number Seat/Chest Positioning Strap w/ AutoStyle Buckle Length (Eyelet to Eyelet)

33" L103652712" - 13" Wide48" L100431014" - 19" Wide61" L103462520" - 22" Wide

#1 Airline Style Positioning Strap

Chair Width Part NumberSeat/Chest Positioning Strap w/

Airline Style Buckle Length (Eyelet toEyelet)46" LTAGTS103475116" - 19" Wide61" L103475220" - 22" Wide



NOTE: Chest Positioning Straps share the same hardware that attaches a Back Upholstery#1 Hook and Loop Style Positioning Strap

Chair Width Part NumberSeat/Chest Positioning Strap w/ Hookand Loop Style Buckle Length (Eyelet

to Eyelet)45" L1034744

12" - 15" Wide See Note(s) A61" L1034745

16" - 22" Wide See Note(s) AA - Hook and Loop Style Positioning Straps for power chairs is used for chest positioning only. NOTE:

#1 Pelvic Restraint Belt w/ Auto Style Buckle (TRRO Option Only)

Chair Width Part NumberPelvic Restraint Belt w/ Auto Style

Buckle Length For TRRO Option Only(Bushing Hole to Bushing Hole

Length)37" L116851312" - 16" Wide55" L1168514

16" - 22" Wide See Note(s) AA - Includes the Pelvic Restraint Belt and items 8-10 NOTE:


Part Number Description Quantity per Assembly

1WARR RPLMT - Charger, Battery, 8

Amp, 115VAC (Off Board)Single Mode Round Plug w/ AC

Power Line Cord, CTE Corp.1123249E-NLA

See Note(s) A

A - See Category "Battery Chargers & Cables" for more information. NOTE:

Warranty Replacement Parts


Invacare Corporation www.invacare.com

One Invacare WayElyria, Oh USA44036-2125800-333-6900

Technical Support800-832-4707Customer Service800-333-6900

Literature Orders800-333-6900

Form No. 10-076

© 2021 Invacare Corporation. All rightsreserved. Republication, duplication ormodification in whole or in part is prohibitedwithout prior written permission fromInvacare. Trademarks are identified by ™and ®. All trademarks are owned by orlicensed to Invacare Corporation or itssubsidiaries unless otherwise noted. (Revised 01/13/21)

fdx® (formula™ cge option included) and front riggings · g,i 1163181-nla nla - owner's...

Documents