fedora 12 x86

8/7/2019 Fedora 12 x86

http://slidepdf.com/reader/full/fedora-12-x86 1/13

Fedora 12 x86_64

This guide is released under the Creative Commons Attribution-ShareAlike license.

Pre-installation steps:

0. Go to http://fedoraproject.org/en/get-fedora-all

1. Download the Fedora 12 x86_64 Install DVD - http://download.fedoraproject.org/ [...] 64-DVD.iso and the checksum file http://download.fedoraproject.org/ [...] 4-

CHECKSUM

2. Verify the download by checking the checksums following these instructions https://fedoraproject.org/en/verify

3. If the checksums are good, burn Fedora-12-x86_64-DVD.iso onto a blank DVD as an ISO image using software that knows how to handle DVD ISO images.

4. After you've successfully recorded the DVD, remove it from the drive and take it over to the computer where you want to install Linux. I 'm assuming you're installing

Linux on a new empty hard drive. Don't do this on a computer with data that you don't want to lose.

5. Turn the computer on, hit DEL, F1, F2 or the appropriate key to go into your BIOS. Inside your BIOS you'll have to look for the screen where you can change the

boot order so you'll be able to boot from your DVD drive. Make sure you've selected your DVD drive as the first boot device, then save your BIOS settings and exit.

Installation steps:

0. Insert the Fedora DVD in your DVD drive and hit enter to start the installer.

8/7/2019 Fedora 12 x86


1. You'll have to wait a little while for the kernel to boot and start the installation, on the next screen you'll be prompted to start a media check . You should select ok

and hit enter to go to the next screen.

2. On the next screen you'll have to select Test and hit enter to start the media check.

8/7/2019 Fedora 12 x86


3. You'll get a sliding progress indicator bar.

4. If the media check is successful the dvd will be ejected automatically and you'll be asked if you want to check another disk. Since you don't want to test any more

disks push the disk back in and after the dvd stops reading select continue. At that point you'll see anaconda starting up.

8/7/2019 Fedora 12 x86


5. After anaconda starts up you'll see a fedora splash screen, you'll need to click Next to go to the next step.

6. You'll need to select your keyboard and click Next to go to the next step.

8/7/2019 Fedora 12 x86


7. Enter a name for your computer and click Next, if you're not sure what name you want to use you can use the default and change it later.

8/7/2019 Fedora 12 x86


8. On the next screen you'll have to select your timezone and whether your BIOS is using UTC/GMT and then click Next.

9. On this screen you'll prompted to enter your root password which has to be at least 6 characters. You'll be warned if you've chosen a weak password. You shouldchoose a very strong password to keep your system safe and secure.

8/7/2019 Fedora 12 x86


Message edited by linux_0 on 02-23-2010 at 09:46:13 AM

------------------------------ $GNU_Linux=$Linus_Torvalds=AWESOME();

R eply to linux_0

linux_0 02-22-2010 at 03:52:33 AM

10. Warning: I'm assuming you're installing on an emtpy drive, the options selected on these screens will overwrite your hard drive. If you don't want

to delete your entire drive stop here. Next you'll have to choose which drive you want to install on if you want to encrypt the system and whether on not to modify

the partitioning layout. If you're experienced with partitioning you should select Review and modify partitioning layout.

8/7/2019 Fedora 12 x86


11. If you've selected Use entire drive on the previous screen fedora's going to automatically select a fairly reasonable default layout. You don't have to chance this

unless you want to save some space for another operating system. Dual booting's going to be covered in a future guide.

8/7/2019 Fedora 12 x86


12. If you're happy with the partitioning click Next and Write changes to disk.

8/7/2019 Fedora 12 x86


13. If you've opted to enable encryption you'll be prompted for your secret key. You should choose a very strong encryption key to keep your system safe and secure.

Make sure you don't lose or forget it, the system's going to ask you for your ecryption key every time you boot. Don't write it on a post-it(TM) note and stick it under

your keyboard or on your monitor, if you can't remember it and you've got to write it down put it in a fireproof safe. If your computer's lost or stolen and your

encryption key is taped to your computer other people are going to be able to get all your files and data. When you're done with the ecryption key you can also use a

bootloader password if you're so inclined. The default bootloader settings are safe for most users so click Next. Again, dual booting's going to be covered in a future

guide.

14. On this screen you'll be able to select what software you'd like to install on your computer. It's best to select Office and Productivity, Customize later and click

next. If you've going to install nvidia kerne l drivers, ATI drivers, VirtualBox or anything along those lines select Software development too. The Web Server's optional,

it's up to you. If you've happy with your selections click Next.

8/7/2019 Fedora 12 x86


15. You'll see a progress indicator for the package dependencies and then two more progress indicators on the next screen. The installer's going to show each package

as it's installed.

8/7/2019 Fedora 12 x86


16. Finally when the installer's done installing packages it'll prompt you to reboot. Click the reboot button to do so. The installer's job is done at this point.

8/7/2019 Fedora 12 x86


This guide is released under the Creative Commons Attribution-ShareAlike license.

Message edited by linux_0 on 02-23-2010 at 09:47:36 AM

------------------------------ $GNU_Linux=$Linus_Torvalds=AWESOME();

fedora 12 x86

Documents