ffs catalog principal

7/28/2019 Ffs Catalog Principal

1/343

2012 Product Catalog


2/343


3/343

Franklin Fueling Systems has contributed many innovative product designs to the petroleum industry, including the

highest performing submersible pumping systems available. Franklin Fueling Systems offers 2 hp and 4 hp models to

meet the needs of high volume retailers and variable speed technology provides constantflow during peak businesstimes, as well as efficiencies during off peak times. The innovative MagShell design is an expanded motor shell option

which increases the flow around the motor by 45%, resulting in significantly higher flow rates. For those high-volumedispensing sites, FFS also offers either a 3 or 5 hp high capacity pump. Intelligent pump controllers, like the STP-SCI

smart controller and the MagVFC variable frequency controller, provide unmatched user interface and fault

detection capabilities to keep your station running.

Submersible Pumping Systems

Service station hardware, marketed under the EBW and Phil-Tite brand names, comprise the most comprehensive

line of service station hardware in the industry. Products include complete lines of both aboveground and

underground components.

Service Station Hardware

Franklin Fueling Systems piping and containment products make up the industrys most complete line of installationcomponents, both underground and aboveground. These products carry the APT brand name and include piping,fittings, sumps and boots.

Piping & Containment

Franklin Fueling Systems manufactures and markets a complete line of Stage II vapor recovery systems globally underthe Healy product brand. Since 1983 when Healy introduced the worlds first vacuum-assist vapor recovery system,

our dispensing systems products have been in service throughout the world. Healy has remained the leader in thedesign and development of new Stage II vapor recovery technologies, which contribute to cleaner air and a healthierenvironment. Healy products are proven performers in Stage II vapor recovery, including the first to test and pass all

the current Enhanced Vapor Recovery (EVR) and Onboard Refueling Vapor Recovery (ORVR) specifications of theCalifornia Air Resource Board (CARB).

Dispensing Systems

Franklin Fueling Systems manufactures and markets a complete line of fuel management systems globally under theINCON product brand. Automatic tank gauges, electronic line leak detection, magnetostrictive probes and remote

monitoring software are just some of the products available.All are designed and manufactured using state-of-the-art technology to meet all of our customers fuel management

and leak detection compliance needs.

Fuel Management Systems

Franklin Fueling Systems Tank Transport Systems product line is comprised of an extensive line of products for both

loading and off loading applications. Connecting to loading terminals and underground storage tanks is made easywith a broad line of FFS adapters, elbows, and valves. FFS has the solution to handle any product drop or vapor

recovery situation. Preventing overfills at the loading rack is a top priority to any transporter. The FFS Optic ControlOverfill Protection System (OCS) is designed to prevent such overfills and is compatible with all existing racks and

monitors. Specialty items including Pressure Relief Valves, Hose Tube Doors and Side Seal Adapters compliment the

system. Each component of the Tank Transport System is designed and manufactured to work in even the toughestof environments.

Tank Transport Systems

Total System Solutions


4/343

Table of Contents

Submersible Turbine Pumps 8

Submersible Turbine Pump Ordering Guide 11Variable Speed Submersible Turbine

Pump Specifications 12

Intelligent Submersible Turbine Pumps 15

Fixed Speed Submersible Turbine Pumps 18

2 hp Specifications 19

1 hp Specifications 22

1/3 and 3/4 hp Specifications 25

Fixed Length Specifications 28

Mechanical Line Leak Detector 30

Submersible TurbinePump Controllers 32

Single-Phase Smart Controller 32

Dispenser Hook Isolation 34

Single-Phase Control Box 36

Submersible TurbinePump Accessories 37

Submersible Turbine PumpRepair Parts 38

High Capacity SubmersibleTurbine Pumps 42

High Capacity Pump Ordering Guide 44

High Capacity Line Leak Detector 48

High Capacity Pump Controllers 50

Three-Phase Smart Controller 50

STP-CB 3/5 Magnetic Starter 52High Capacity Pump Repair Parts 53

Submersible Pumping Systems

Please visit www.franklinfueling.com/approvals to view Franklin Fueling Systems Intellectual Property information.

Underground Storage Tank Equipment 56

300 Vapor Check Valve Adapter 56

304 4" Vapor Recovery Cap 57

306/708 4" Coaxial Vapor Recovery Adapter 58

308 Ball Float Vent Valves 59

300 Series Extractor Vent Valves 60

Extractor Vent Valve Accessories 61

362 Vapor Shear Valve 62

662 Emergency Shut-off Valves 63

Emergency Shut-off Valve Accessories 64

Emergency Shut-off Valve

Replacement Tops 64

775 4" Side Seal Fill Cap 65776 4" Side Seal Fill Adapter 66

777 4" Top Seal Fill Caps 67

778 Top Seal Fill Pipe Adapter 68

SWF-100 Top Seal Swivel Fill Pipe Adapter 69

SWV-101 Top Seal Swivel Vapor Pipe Adapter 70

779 3" Top Seal Fill Cap 71

Autolimiter II Automatic Shut-off Valve 72

Remote Fill Kit 74

782 Drop Tubes 75

Probe Cap and Adapter Kit 76

Tank Bottom Protectors 76PV-Zero 77

Spill Containers 78

Defender Series Spill Container 78

15 Gallon Secondary Contained

Spill Containers 81

Field Replaceable 5 Gallon Direct Bury Spill

Containers with Corrugated Gravel Shield 82

Field Replaceable 5 Gallon Direct Bury Spill

Containers with FRP Gravel Shield 83

Spill Container Replacement Parts 84

702, 705 and 715 Grade Level

Spill Containers 85

Grade Level Spill Container Accessories

and Replacement Parts 87

702, 705 and 715 Below Grade Level

Spill Containers 88

Service Station Hardware

Continued on next page...


5/343

Table of Contents


Manways 90

7-1/2", 12" and 18" Round Manways 90

Steel Manways 91

16" and 24" Square Manways withKnock Down Skirts 93

12", 30", 36" and 42" Fiber Reinforced

Composite Manways 94

Containment Manhole 96

Monitoring Test Well Manways 97

Monitoring Test Well Accessories 98

787 Series Fuel Identification 100

Multi-port Containment 101

Multi-port Manways 101

Multi-port Manway Packages 102

Watertight Fiberglass Multi-port

Sump Packages 104

Watertight Fiberglass Multi-port Sump

Package Accessories 105

EVR Phase 1 Packages 106

Phase I Vapor Recovery Solutions 107

Aboveground Storage Tank Equipment 108

605, 606, 616 and 636 Anti Syphon Valves 108

664 Pressure Regulator Valve 109706 AST Spill Container 110

709 Warden Aboveground Storage

Tank Overfill Prevention Valve 111

Fill Caps 112

800 Tank Vents 113

802 Pressure Vacuum Vents 114

803 Aboveground Emergency Vents 115

Nozzles 116

402 Utility Nozzle 116

410 Fuel Oil Delivery Nozzle 117

415 Automatic Bulk Fueling Nozzle 117

490 Dual Poppet Nozzle 118

498 Manual Nozzle 118

495 Aircraft Fueling Nozzle 119

Nozzle Accessories 120

Safety-Sever Emergency Breakaways 122

697/698 3/4" Safety-Sever Breakaway 122

797 1" Safety-Sever Breakaway 122

Suction System Equipment 123

50-201 Brass Foot Valves 123

320 Foot Valve Extractor 124

325 Product Line Isolation Valve 125

515 and 516 Brass Vertical Check Valves 126

615 and 635 Angle Check Valves 127

621 and 622 Under Pump/In-Line

Check Valves 128

650 Union Check Valve 129

Installation Tools 130Wrenches 130

Flaring Tool 131

Spill Container Tool Kit 131

Accessories 132

Debris Buckets 132

M/F 44 132

Alignment Brackets 132

48-409 132

Cover Removal Tool 132

Replacement Parts 133

Approvals 137Continued on next page.


6/343

Table of Contents

Piping 139

XP Pressure and Suction Product Piping 139XP Marina/Aboveground Product Piping 141

4" Ducting 143

Fittings 144

XP Clamshell Swivel Pipe Fittings 144

XP Male Swage Swivel Pipe Fittings 145

XP Clamshell Non-Swivel Pipe Fittings 145

XP Clamshell Non-Swivel Tee and

Elbow Pipe Fittings 146

XP Quick Release Fittings 147End Connections and Fittings 148

2" Vent Conversion Box Fittings 150

Termination Boots 151

Flexible Entry Boots 151

Flexible Double Entry Boots 153

Flexible Bulkhead Boots 155

MD-Series Flexible Entry Boots 157

Clamshell Secondary Test Boots 158

Swage Secondary Air Test Boots 159

Transition Sleeves 161

Grade Level Transition Sleeve 161

Wall Transition Sleeve 162

Sumps 163

Below Grade Transition Tank Sumps 163

Below Grade Intermediate Piping Sumps 165

Grade Level Transition Sump 166

4542 Series One-Piece Tank Sumps 168

4736 Series One-Piece Tank Sumps 170

Watertight Fiberglass Turbine Sump Packages 172

Large Mouth Dispenser Sumps 174

Single and Double Wall Fiberglass

Large Mouth Dispenser Sumps 181

Classic Dispenser Pan Sumps 183

Sump Accessories 184

Tank Fitting Adapters 184Tank Manway Adapters 185

Stabilizer Bar Kits 185

Accessories 186

Installation Tools 186

Swage Kits 186

UPP Piping 187

UPP Fittings 188

UPP Termination Fittings 193

UPP Entry Boots 195

UPP Turbine Sumps 197

UPP Installation Tools 198

Piping & Containment


Dispensing SystemsProduct Selection Guide 201

Enhanced Vapor Recovery - Phase II 202

9961 Clean Air Separator 202

Stage II Vapor RecoveryDispenser-Mounted Vacuum Sources 203

VP1000 Series Dispenser-Mounted

Vacuum Source 203

VP1000 Replacement Parts 206

VP1200 Series Self-Contained Suction Pump

Dispenser-Mounted Vacuum Source 207

Stage II Vapor Recovery Nozzles 208

400 Series ORVR Nozzle 208

600 Series Bootless Nozzle 209




900 Series EVR Certified Nozzle 213

Hoses and System Accessories 214

Standard Healy and Whip Hoses 215

Metric- and Balance-Ready Hoses 217



7/343

Table of Contents


S7 Series Hoses 219

Hose Adapters, Breakaways, Kits

and Spare Parts 221

Stage II Vapor RecoveryCentral Vacuum Sources 222

9000 Series Mini-Jet Central Vacuum Pump 222

VP500 Central Vacuum Vane Pump 223

VP500C/1 or VP500C/2 Cabinet Models 224

Fuel Management System Consoles 227

TS-550 evo Fuel Management System 227TS-5 Fuel Management System 229

TS-550 & TS-5000 Fuel Management Systems 231

Console Accessories 233

Environmental & Tank Monitoring 235

Colibri Tank Monitor 235

TS-EMS Environmental Monitoring System 237

In-Station Diagnostics 239

Tank Sentinel Consoles 240

TS-1001 Full Feature Compliance Console 240TS-1001/G Fixed Feature Generator Tank

Monitoring Console 242

TS-504 and TS-508 Fixed Feature Inventory

Control Consoles 243

TS-750 Fixed Feature Tank Monitoring and

Compliance Kits 245

Tank Sentinel Console Accessories 247

S940 Sensor Alarm Console 248

Electronic Line Leak Detectors 249TS-L300 AutoLearn 249

Line Sentinel 251

Probes and Sensors 253

Leak Detection & Inventory Control Probes 253

Moorman Level Gauge Kit 255

Float Kits 256

Density Measurement Float Kit 257

Probe Installation Kits 258

TSP-HIS Hydrostatic Interstitial

Brite Sensor 259

TSP-DIS Discriminating Interstitial

Brite Sensor 260

TSP-EIS Electro-Optic Interstitial Sensor 261

TSP-HFS Horizontal Float Sensor Switch 261

TSP-ULS Liquid Sensor 262

TSP-UHS Universal Hydrostatic Sensor 262

TSP-DMS Discriminating

Magnetostrictive Sensor 263

TSP-DDS Discriminating Dispenser

Sump Brite Sensor 264

TSP-DTS Discriminating Turbine Sump

Brite Sensor 264

TSP-DVS Discriminating Vapor Brite Sensor 265

TSP-MWS Monitoring Well Brite Sensor 265

TSP-HLS Level Sensor 266

DC400 Dispensing Cutoff System 267

Sensor Installation Kits 269

Sensor Installation Accessories 271

External Console Hardware 272

TS-RA1 Remote Audible and Visible

Alarm Unit 272

TS-RA2 Remote Audible and Visible

Alarm Unit 273

TS-RK Remote Alarm Acknowledge Unit 274

TS-DIM Dispenser Interface Module 275

TS-TPI Turbine Pump Interface 277

Fuel Management Systems

100 Jet Pump Central Vacuum Source 224

System Monitor 225

6280 Vapor Recovery Monitoring System 225

System Test Equipment 226

Continued on next page.


8/343

Table of Contents

TS-ROM2 BriteBox Relay Output Module 278

TS-EPS Ethernet Port Server 279

External Console Hardware Accessories 279

Software 280System Sentinel Remote Fuel

Management Software 280

System Sentinel AnyWare Internet Enabled

Fuel Management Software 282

Get Connected AnyWare Remote

Polling Service 283

Accessories 286

Sump Test System Kit 286

Spare Parts 288

TS-5, TS-550, TS-5000,TS-EMS and TS-550

evo Consoles 288

Colibri Consoles 288TS-504 and TS-750 Consoles 288

TS-508 Console 289

TS-1001 Console 289

TS-2001 Console 289

DC400 289

TS-LLD 290

TS-LS300 290

TS-LS500 290

TS-STS Sump Test Kit 290

Accessories 290

Transport Systems Overview 291

Transport Systems Solutions 291

Fuel and Vapor Transfer Solutions 292

API Bottom Loading Adapters 294

API Bottom Loading Adapters 294

API Bottom Loading Adapter Spare Parts 295Dust Cap 296

Air Interlock Valves 297

Three-Way Air Valves 297

Six-Way Air Valves 299

Air Interlock with Limit Switch 301

Gravity Drop Adapters 302

Female Gravity Drop Adapters 302

Male Gravity Drop Adapters 303

Vapor Check Valves 304

Threaded Vapor Check Valve 304

Flanged Vapor Check Valve 306

Vapor Caps 308

Vapor Return Hose Couplers 310

Air-Operated Sequential Vapor Valves 311

Hose Tube Doors 313

Product Drop Elbows 314

Dual Point Vapor Recovery Elbow 318

Coaxial Delivery Elbow 320

Attachments 322

Gasket Kit 322

Sight Glass Kit 322

3" Cam and Groove Adapter 323

4" Cam and Groove Adapter 323

3" NPT Male Adapter 323

4" NPT Male Adapter 323

Cam and Groove Adapters 324

Emergency Valves 325

Mechanically Operated 90 Degree (Victaulic)325

Mechanically Operated 90 Degree (Flanged) 326Air Assisted 90 Degree (Victaulic) 327

Air Assisted 90 Degree (Flanged) 328

3" Emergency Valve 329

Side Seal Adapter 330

Bulk Pneumatic Pressure Relief Valves 331

Tank Transport Systems



Victaulic is a trademark of Vitaulic Company of America.


9/343

Table of Contents


Optic Control System 333

OCS Overfill Protection Solutions 333

Two-Wire Controller 334

Two-Wire Optic Overfill Probes 334Two-Wire Optic Retained Product Probes 335

OCS Probe Solutions 336

Probe Holder Solutions 336

Single Socket Solutions 337

Installation Kits 338

Wiring Kits 338

Cross Reference Guide 339


10/343

8

Submersible Turbine Pumps

Advantages

Faster Fueling Times - Withinnovations like MagShell, FE

Petro products set the standard forsubmersible pump performance.

Active Air Eliminator - FE Petroproducts come standard with activeair elimination, which eliminates airthrough the highest point in the pumphead at all times when the pump isrunning, assuring air does not pass intodischarge piping.

Safety and Easeof Maintenance - FE Petro STPsinclude a contractor electricaldisconnect, which requires looseningonly one bolt, allowing motor wiringto be disconnected without venting

the dangerous tank vapors intothe sump when servicing FE Petrosubmersible products.

Simple Servicing - If ever required,the pump can be easily removed fromthe tank by unthreading three bolts.There is no need to disconnect thesyphon system or to remove the leakdetector from the system to servicethe STP.

Since the mid-1950s, Franklin Electric, the parent company of Franklin Fueling Systems, hasbeen involved in the design and manufacture of submersible motors for use in pumping liquids.

Building on this extensive history, FFS has contributed innovative product designs forsubmersible pumps into the twenty-first century. Marketers concerned about fueling times,efficiency, serviceability, reliability and overall quality find it an easy choice to specify FE Petroproducts from FFS.

Consider these unique FE Petro product features to improve the profitability of yourretail operations:

Active Air Eliminator

Safety and Ease of Maintenance

Simple Service


Faster Fueling


11/343

SUBMERSIBLEPUMPING SYSTEMS

9


Manual Pressure Relie

Reliable Check Valve

Variable Length

Advantages

Manual Pressure Relief -A standard FE Petro feature. A

vent screw is provided to bleed linepressure to zero when necessary. Byturning this screw, product is divertedback to the tank, dropping linepressure to zero. This reducesfuel discharged into the sump manholeor dispenser pan during servicing,further protecting service techniciansand the environment.

Reliable Check Valve - The STPuses FE Petros proven line checkvalve. At 2 in diameter, this valvereduces pressure loss at high flowrates resulting in faster fueling times.

Variable Length - The VL2 pump

fits 94% of all known tank diametersand tank bury depth combinations.The VL1 and VL3 are available tohandle installations shorter or longerthan this range. The telescopingconnection is a patented FE Petrofeature. Pump length can be set bymaking one simple measurementand setting the pump length withoutaffecting the UL listing of the pump.


12/343

10


12.50"

10.65"

5.80"

DISCHARGE/LEAKDETECTOR

RISER/COLUMN PIPECENTERLINE

SIPHON

LU

TANK PORT" NPT

SYPHON PORT" NPT

LEAK DETECTOR

PORT - 2" NPT

DISCHARGE OUTLET2" NPTRISER PIPE

4" NPT

T

K

CENTERLINE

7.55"RADIUS

11.70"

5.80"

3.00"

RISER/COLUMN PIPEDISCHARGE/LEAK DETECTORCENTERLINE CENTERLINE

LINE TEST PORT" NPT

10.45"8.12"

RADIUS

UPFORSERVICE

DOWNFORTEST

LINEPRESSURETEST

RE

CEL

E

TREMO

VING

COV

ER

TIGHT

R

D

IR

E' VELN

VUO

CR

N

C

AV

LE

A

VU

OT

I

IU

KEEP

COVER

BEFO

RE

OPEN

CIRC

UIT

EL

CR

OPEN

CIRCU

IT

REMO

VING

COV

ER

BEFO

RE

E

COVE

R

TIGH

TKEE

P

V

RE

UO

CU

IL

C

T

EN'D

C

L

NVAAEEV

ELR

RIEL TC

RI

VROU


13/343


1

BOTTOMCLEARANCE5" TYPICAL

EFFECTIVETANK

DIAMETER(ETD)

TANK INSIDEDIAMETER

B -RISER

LENGTH

GRADE LEVEL

MANHOLE

LEAKDETECTOR(MLD)

TURBINEMANIFOLD

CONTAINMENTSUMP

4" RISER PIPE

SUMP ADAPTER

TANKMANWAY

PUMP MOTOR(PMA)

11.00"REF

PUMP HEADCLEARANCE

BURYDEPTH

A -MODELLENGTH

LU

SYPHON

T

K

Notes: 1. Effective tank diameter (ETD) = Inside tank diameter (to top of 4" bung), including tank manwayand/or sump adapter.

2. Model length (A) = ETD plus riser length minus bottom clearance minus 1" thread engagement.3. Riser length (B) = Bury depth (to top of tank) minus pump head clearance minus tank manway

and/or minus sump adapter.

12.50"REF


Submersible Turbine PumpOrdering Guide


14/343

12


Variable SpeedSubmersible TurbinePump Model Designation

SystemA typical turbine model designationhas up to five components to definethe pump being supplied as follows:

STP XXXXX Y - A - B

STP= Basic Model Designation

Note: All STP models include theoptions for alcohol-gasolinecompatibility, variable speed andvariable length as part of thebase model.

XXXXX = Factory InstalledOptions

STP model designations may includeone or more of the followingcharacters in alphabetical order:

F = Floating suction adapter (1" NPTfemale adapter)

K = Intake filter screen (IFS, factoryinstalled to PMA)

M = MagShell (flow enhancing,expanded PMA shell)*R = Model R check valve (24 psirelief/22 psi reset for PLLD)*W = Model W check valve (16 psirelief/13 psi reset for PPM4000)

*Note: If not otherwise specified, allSTP models are supplied withstandard model check valve(40 psi relief/35 psi reset forMLD and TS-LS300).

Y = Pump Motor HorsepowerRating

VS2 = 2 hp variable speed

VS4 = 4 hp variable speed

A = Model Length

VL1 = Variable length range #1.



Note: VL2 models fit 94% of allknown installations.

B = Riser Pipe Length

Riser pipe length is expressed as twonumeric characters that indicate thetotal length of the riser in inches. Riserpipes are available from 7" to 69" in1" increments (additional charge forrisers 31" or longer).

Power Requirements

VS models can only be powered by aMagVFC controller:

VS2 models can operate with single-or three-phase incoming power supply tothe MagVFC.

VS4 models require three-phaseincoming power supply to the MagVFCfor proper operation.

Incoming power supply to the MagVFCcan be 200-250 VAC, 50 or 60 Hz.

MagVFC outputs a three-phase, variablefrequency signal, valid for FE Petro variablespeed pumps only.

VS2 max. motor draw: 9 Amps.

VS4 max. motor draw: 15 Amps.

MagVFC max. line draw: 20 Amps.

Pump Motor

2 hp or 4 hp, variable speed, two-stagecentrifugal type pump motor with integral,automatic, thermal overload protection.

Max. flow: VS2 = 110 gpm, VS4 = 140 gpm.

Max. pressure: selectable operatingpressure on MagVFC between 24 psi and42 psi deadhead.

Available with MagShell which results in45% increased flow area around motor.

Liquid Compatibility

Max. liquid viscosity: 70 SSU at60 F (15 C).

Variable speed models are UL and cULlisted for fuel mixtures containing up to10% ethanol, and 20% MTBE, 20% ETBE or17% TAME with gasoline.

Variable speed (non-AG) models can alsobe used with diesel fuels, fuel oils,kerosene, Avgas and jet fuels in anon-gelled pourable state.

All wetted elastomers are made of a highgrade, fluorocarbon compound.

Standard Features

Variable speed models are available invariable and fixed length options.

Check valve: 2" diameter fluorocarbonseal constructed on cast aluminum bodyand steel backing washer.

Pressure relief valve: available in fourpressure relief settings, integral to checkvalve. Standard model relieves at 40 psi andresets above 35 psi.

Syphon: venturi-type syphon primersupplied with every submersible. Syphoncheck valve and secondary syphonsold separately.

Air eliminator: every submersible includes atank return path with one-way check valveto provide active air elimination.

Electrical disconnect: electrical yokefor positive contractor disconnectduring service.

Approvals

Consult factory for applicable approvals.

Quality Certification

Franklin Fueling Systems is an ISO 9001Certified Manufacturer.

For full diagram see page 11.

B

A

LU

SYPHON

T

K

Variable Speed Submersible TurbinePump Specifications


15/343


13


4 hp Variable Speed Turbine Performance Chart

0

10

20

30

40

50

60

70

80

90

100

110

120

130

140

0 20 40 60 80 100 120 140 160 180 200 220 240 260 280Flow in Gallons per Minute (gpm)

TotalHeadinFeet(ft.)

Note: Performance based on pumping gasoline (0.76 specific gravity). Pressure is taken at the manifolddischarge outlet. ISTMVS4 and STPMVS4 turbines can only be powered by a MagVFC withthree-phase incoming power.

Two MVS4, Manifolded 4 hp

MagShellVariable Speed Pumps

One MVS4 4 hp MagShell

Variable Speed Pump

2 hp Variable Speed Turbine Performance Chart

0

10

20

30

40

50

60

70

80

90

100

110

120

130

140

0 20 40 60 80 100 120 140 160 180 200 220Flow in Gallons per Minute (gpm)


Note: Performance based on pumping gasoline (0.76 specific gravity). Pressure is taken at the manifolddischarge outlet. ISTM and STPMVS2 turbines can only be powered by a MagVFC with single- orthree- hase incomin ower.

One MVS2, 2 hp MagShell

Variable Speed Pump

Two MVS2, Manifolded 2 hpMagShell Variable Speed Pumps


16/343

14


Model DescriptionModel

Length RangeNumber

ModelLength* Range

STPMVS2-VL1 2 hp variable speed with MagShell VL1 59"-87"






Variable Speed Submersible Turbine Pumps(variable speed, variable length)

Notes: 1. Remove M from model number for non-MagShell pump motor assembly.2. All above models are UL and cUL listed for compatibility with fuel mixtures containing up to 10% ethanol with gasoline,

diesel fuels, and 20% MTBE, 20% ETBE or 17% TAME with gasoline.3. All models are supplied with a standard check valve unless factory option R or W is specified.4. All above models can only be powered by a MagVFC. 4 hp models require three-phase incoming power supply, 2 hp

models can be supplied with single- or three-phase incoming power.5. 4" riser pipe, if supplied locally, must be 4" OD by 3/16" WT tubing.6. For riser pipe lengths 31" to 69", add $45 to list price.

*

Model length (A) defined as the dimension from turbine manifold bottom to pump motor inlet.

Factory Installed Options(specified in model number at time of STP order)

Designation Description

F Floating suction adapter, 1" NPT female, must be factory installed

K IFS (intake filter screen) factory assembled to pump motor assembly

R Model R check valve, factory installed, for Veeder-Root PLLD Line Leak

W Model W check valve, factory installed, for Red Jacket PPM4000 Line Leak

Part Number Description

5874202800 MagVFC, 2 hp or 4 hp variable frequency controller, one required per STPM VS2 or VS4

400137908 Syphon check valve, alcohol-gasoline compatible (when ordered with STPM VS2 or VS4)

402459931 Model 65 psi check valve (for slave of manifolded STPM VS2 or VS4 with Veeder-Root PLLD)

402507930 Secondary syphon kit (when two syphon primes are required for one STPM VS2 or VS4)

5800300100 STP-DHI dispenser hook isolation for 110 volt dispenser handle switches, up to eight each


402671901 Kit with 4 hp variable speed non-MagShell (PMA VS4)

400693901 Kit with 2 hp variable speed non-MagShell (PMA VS2)

Field Installed Options(intelligent submersible turbine pump specific accessories)

Variable Speed Conversion Kits

Note: Kits include variable speed pump motor assembly, MagVFC variable frequency controller, four-wire contractors plug

and installation instructions.

Veeder-Root is a trademark of Danaher Corporation.

Red Jacket is a trademark of Veeder-Root Company.


17/343


15


Advantages

Constant Flow - Depending on peakbusiness requirements, marketers now

have a choice of either 2 hp or4 hp variable speed models. 2 hpprovides constant 10 gpm (38 lpm)for up to eight fueling positionsoperating simultaneously, 4 hp forup to 12 positions.

MagVFC Design Highlights -The MagVFC features a dual sevensegment display to show diagnosticfaults. A serial interface is standard toconnect to INCON System Sentinelsoftware for remote reporting ofpump alarms and sharing otherpump/ATG intelligence. TheMagVFC detects and displays these

system conditions: Dry tank (initiates an immediate

pump shut-down). Continuous pump run. Low incoming voltage. Pump motor failure. Short circuit detection. Controller faults. Open circuit detection.

For reduced installation cost, ashielded power cable is not required.Pump protection extends pump lifeand extended run fault alerts acondition that may render line leakdetection ineffective. Remote

reporting of pump alarms and sharingof IST and ATG intelligence furtherreduce station operating costs.

Meets EPA Spitback Control - TheIST can be adjusted at installation toperform at maximum per nozzle flowrate of 10 gpm (38 lpm) based on thespecifications of your piping anddispensing system. This eliminatesoverpressuring the system, whichresults in an unnecessarily highhydraulic hammer and need forother control devices.

MagVFC

FE Petro introduced the first variable speed submersible pump for the petroleum industry in1995. Since that time, high volume marketers around the world have realized the benefits offilling cars faster during peak business periods that only variable speed submersibles candeliver. Station size and volumes have continued to grow. To meet the needs of these highvolume retailers, FE Petro offers the intelligent submersible turbine pump, the industryshighest performing 4" diameter submersible pump.

Spitback Control

Intelligent SubmersibleTurbine Pumps

Constant Flow

MagVFC


18/343

16


Intelligent SubmersibleTurbine Pump ModelDesignation System

A typical turbine model designationhas up to five components to definethe pump being supplied as follows:

IST XXXXX Y - A - B

IST= Basic Model Designation

Note: All IST models includealcohol-gasoline compatibility,variable speed and variablelength as part of the base model.


IST model designations may include

one or more of the followingcharacters in alphabetical order:



M = MagShell (flow enhancing,expanded PMA shell)

R* = Model R check valve (24 psirelief/22 psi reset for PLLD)

W* = Model W check valve (16 psirelief/13 psi reset for PPM4000)

*Note: If not otherwise specified, all ISTmodels are supplied with

standard model check valve (40psi relief/35 psi reset for MLDand TS-LS300).

Y = Pump Motor HorsepowerRating**

VS4 = 4 hp variable speed**Note: If not otherwise specified, 2 hp

variable speed is implied.

A = Model Length

1 = 2 hp variable length, 59"-87"

2 = 2 hp variable length, 90"-151"

3 = 2 hp variable length, 122-213"

VL1 = 4 hp variable length, 64"-92"

VL2 = 4 hp variable length, 95"-156"

VL3 = 4 hp variable length, 127-218"

Note: IST-2 and ISTVS4-VL2 models fit94% of all known installations.



Power Requirements

IST models can only be powered by aMagVFC controller:

2 hp models can operate with single- or

three-phase incoming power supply tothe MagVFC.

4 hp models require three-phase incomingpower supply to the MagVFC forproper operation.

Incoming power supply to the MagVFCcan be 200-250 VAC, 50 or 60 Hz.

MagVFC outputs a three-phase, variablefrequency signal, valid for FE Petro variablespeed pumps only.

2 hp max. motor draw: 9 Amps.

4 hp max. motor draw: 15 Amps.

MagVFC max. line draw: 20 Amps.

Pump Motor

2 hp or 4 hp, variable speed, two-stagecentrifugal type pump motor with integral,automatic, thermal overload protection.

Max. flow: 2 hp = 110 gpm, 4 hp = 140 gpm.

Max. pressure: selectable operatingpressure on MagVFC between 24 psi and42 psi deadhead.

Available with MagShell, which results in45% increased flow area around motor.

Intelligent Submersible Turbine Pump Specifications



IST models imply alcohol-gasolinecompatibility for fuel mixtures containingup to 85% ethanol, and 20% MTBE, 20%ETBE or 17% TAME with gasoline.

IST models can also be used with dieselfuels, fuel oils, kerosene, Avgas and jet fuelsin a non-gelled pourable state.


Standard Features

All IST models include variablespeed, variable length options andalcohol-gasoline compatibility.



Syphon: venturi-type syphon primersupplied with every submersible.Syphon check valve and secondarysyphon sold separately.

Air eliminator: every submersible includestank return path with one-way check valveto provide active air elimination.


Approvals





B

A

LU

SYPHON

T

K


19/343


17


Model DescriptionModel Length*

Range

ISTM-1 2 hp variable speed with MagShell

59"-87"ISTM-2 2 hp variable speed with MagShell 90"-151"

ISTM-3 2 hp variable speed with MagShell 122"-213"

ISTMVS4-VL1 4 hp variable speed with MagShell 64"-92"



Intelligent Submersible Turbine Pumps(variable speed, variable length, AG compatible)

Factory Installed Options(specified in model number at time of IST order)







5874202800 MagVFC, 2 hp or 4 hp variable frequency controller, one required per IST

400137908 Syphon check valve, alcohol-gasoline compatible (when ordered with IST)

402459931 Model 65 psi check valve (for slave of manifolded ISTs with Veeder-Root PLLD)

402507930 Secondary syphon kit (when two syphon primes are required for one IST)

5800300100 STP-DHI dispenser hook isolation for 110 volt dispenser handle switches, up to eight each


400693905 Kit with AG compatible 2 hp variable speed non-MagShell (PMAAGVS2)

400693906 Kit with AG compatible 2 hp variable speed with MagShell (PMAAGMVS2)

402671905 Kit with AG compatible 4 hp variable speed non-MagShell (PMAAGVS4)

402671906 Kit with AG compatible 4 hp variable speed with MagShell

(PMAAGMVS4)

Field Installed Options(intelligent submersible turbine pump specific accessories)

Variable Speed Conversion Kits(AG compatible)

Notes: 1. Remove M from model number for non-MagShell pump motor assembly.2. All above models are compatible with fuel mixtures containing up to 85% ethanol with gasoline, diesel fuels, and 20% MTBE,

20% ETBE or 17% TAME with gasoline.3. All models are supplied with a standard check valve unless factory option R or W is specified.4. All above models can only be powered by a MagVFC. 4 hp models require three-phase incoming power supply, 2 hp

models can be supplied with single- or three-phase incoming power.5. 4" riser pipe, if supplied locally, must be 4" OD by 3/16" WT tubing.

*Model length (A) defined as the dimension from turbine manifold bottom to pump motor inlet.

Note: Kits include variable speed pump motor assembly, MagVFC variable frequency controller, four-wire contractors plug andinstallation instructions.




20/343

18


Advantages

Highest Flow - The STPM200with MagShell provides flow ratespreviously unavailable in 4" fixedspeed submersible turbine pumps.One pump can provide good flowrates for up to 10 retail nozzlesflowing simultaneously. FE Petro offersthe 2 hp performance in bothstandard and high pressure models tofit any application.

MagShell - MagShell is a featureon our 2 hp models. The pump motorshell is expanded to increase the flowarea around the motor by 45%,resulting in significantly higher flowrates. MagShell is constructed of 304stainless steel and is the highestperforming 2 hp fixed speedsubmersible ever offered.

Faster Fueling Times - FE Petro 1and 2 hp turbines fuel cars fasterduring peak business hours due to thehigher pump performance.

Easy Upgrade - If you have existingSTPs in your stations and want fasterflow rates, consider upgrading to a2 hp MagShell pump motor fromFE Petro. The pump motor iscompatible with existing FE Petro andcompetitive-make submersible pumpsand can increase flow rates (1 to 2gpm per nozzle with 5-8 nozzles

operating) and go easy on your budgetat the same time. FE Petro pumpmotors sell for about one-third thecost of a complete pump change-out.

Fixed Speed SubmersibleTurbine PumpsFE Petro has contributed innovative product designs for submersible pumps into the twenty-first century. With the introduction of a 2 hp fixed speed submersible pump, FE Petro alsointroduced the MagShell innovation to improve the profitability of retail operations.n ro uce e ag e nno

120

100

80

60

40

20

TotalH

eadinFeet(ft.)

Flow in Gallons per Minute (gpm)

2 hp vs. 1 hp Pump Performance

0 20 40 60 80 100 11010 30 50 70 90

PMA 150

PMAM200

PMA HM200


21/343


19


2 hp Fixed SpeedSubmersible TurbinePump Model Designation


STP XXXXX Y - A - B




AG = Alcohol-gasoline compatible (85%

ethanol or 100% biodiesel capable)Note: Standard models 0% to 10%

ethanol capable.


H = High pressure (45 psideadhead output)


M = MagShell (flow enhancing,expanded PMA shell)*R = Model R check valve (24 psirelief/22 psi reset for PLLD)*W = Model W check valve (16 psi

relief/13 psi reset for PPM4000)*Note: If not otherwise specified, all

STP models supplied withstandard model check valve(40 psi relief/35 psi reset forMLD and TS-LS300).


200 = 2 hp fixed speed

A = Model Length







Power Requirements

2 hp fixed speed models requiresingle-phase, 208-230 VAC, 60 Hz

incoming power. 2 hp fixed speed models incorporate a

starting and running capacitor, withinternal bleed resistor, rated 370 Volt,40 microfarad.

STP-SCI single-phase smart controllers andSTP-CBS single-phase control boxes areavailable for 2 hp pump control.

Max. motor draw: 12 Amps.

Pump Motor

2 hp fixed speed, 3450 rpm, multi-stagecentrifugal type pump motor with integral,automatic, thermal overload protection.

Standard pressure (two-stage) model, max.flow = 120 gpm, max. pressure = 36 psi.

High pressure (H200, three-stage)model, max flow = 105 gpm, max.pressure = 45 psi.

Available with MagShell for 45% increasedflow area around motor.

2 hp Fixed Speed Submersible TurbinePump Specifications


Max. liquid viscosity: 70 SSU at 60 F(15 C).

Standard STP models are UL and cUL listedfor fuel mixtures containing up to 10%ethanol, and 20% MTBE, 20% ETBE or 17%TAME with gasoline.

STPAG (AG compatible) models are forfuel mixtures containing up to 85% ethanolor 100% biodiesel, and 20% MTBE, 20%ETBE or 17% TAME with gasoline.

2 hp fixed speed models can also be usedwith diesel fuels, fuel oils, kerosene, Avgasand jet fuels in a non-gelled pourable state.


Standard Features

2 hp fixed speed models are available invariable length and fixed length options.

Check valve: 2 diameter fluorocarbonseal constructed on cast aluminum bodyand steel backing washer.


Syphon: venturi-type syphon primersupplied with every submersible. Syphoncheck valve and secondary syphon soldseparately.



Approvals



Franklin Fueling Systems is an ISO 9001

Certified Manufacturer.


B

A

LU

SYPHON

T

K


22/343

20


2 hp Fixed Speed Turbine Performance Chart

0

10

20

30

40

50

60

70

80

90

100

110

120

130

140

0 20 40 60 80 100 120 140 160 180 200 220



Note: Performance based on pumping solvent (0.78 specific gravity). Pressure is taken at the manifolddischarge outlet. STPM200 models are powered by a single-phase, 60 Hz, 208/230 Volt power supply.

One STPM200 2 hp

MagShell Fixed Speed Pump

Two STPM200, Manifolded 2 hp

MagShell Fixed Speed Pumps

2 hp High Pressure Fixed Speed Turbine Performance Chart

0

10

20

30

40

50

60

70

80

90

100

110

120

130

140

0 20 40 60 80 100 120 140 160 180 200 220Flow in Gallons per Minute (gpm)


Note: Performance based on pumping solvent (0.78 specific gravity). Pressure is taken at the manifolddischar e outlet.STPHM200 models are owered b a sin le- hase ,60 Hz,208/230Volt ower su l .

One STPHM200 2 hp

High Pressure MagShell Pump

Two STPHM200

Manifolded 2 hp High

Pressure MagShell Pumps


23/343


2



Length RangeNumber

ModelLength*

Range

STPM200-VL1 2 hpfixed speed with MagShell

VL1 63"-91"STPM200-VL2 2 hp fixed speed with MagShell VL2 94"-154"

STPM200-VL3 2 hp fixed speed with MagShell VL3 126"-217"

STPHM200-VL1 2 hp high pressure fixed speed with MagShell VL1 63"-92"



Alcohol-Gasoline Model

DescriptionModel

Length RangeNumber

ModelLength*

Range

STPAGM200-VL1 2 hp AG fixed speed with MagShell VL1 63"-91"



STPAGHM200-VL1 2 hp AG high pressure fixed speed with MagShell VL1 63"-92"



2 hp Fixed Speed Submersible Turbine Pumps


400137908 Syphon check valve, alcohol-gasoline compatible (when ordered with STP)

400818921 STP-CBS, single-phase control box with lockout switch, 110 Volt coil

402312921 STP-DHI-SCI, combo DHI with factory wired STP-SCI (when purchased with a 4" STP)

402312921 STP-DHI-SCI, combo DHI with factory wired STP-SCI (when purchased without a 4" STP)*

402313921 STP-DHI-CBS, combo DHI with factory wired STP-CBS

402459931 Model 65 psi check valve (for slave of manifolded STPs with Veeder-Root PLLD)

402507930 Secondary syphon kit (when two syphon primes are required for one STP)

5800100215 STP-SCI, single-phase smart controller (when purchased without a 4" STP)

5800100215 STP-SCI, single-phase smart controller (when purchased with a 4" STP)*

5800300100 STP-DHI, dispenser hook isolation for 110 Volt dispenser handle switches, up to eight each

Field Installed Options(2 hp fixed speed specific accessories)

Notes: 1. Remove M from model number for non-MagShell pump motor assembly.2. STP models are compatible with fuel mixtures containing up to 10% ethanol with gasoline, and 20% MTBE, 20% ETBE or

17% TAME with gasoline.STPAG models are compatible with fuel mixtures containing: up to 100% biodiesel or 85% ethanol with gasoline, and 20%MTBE, 20% ETBE or 17% TAME with gasoline.

3. All models are supplied with a standard check valve unless factory option R or W is specified.4. All above models require single-phase, 208-230 VAC, 60 Hz incoming power.5. 4" riser pipe, if supplied locally, must be 4" OD by 3/16" WT tubing.


*When purchasing STP-SCI or STP-DHI-SCI in equal quantities offixed speed 4" STPs, the STP-SCI or STP-DHI-SCI will beinvoiced at special discount pricing.


Designation DescriptionF Floating suction adapter, 1" NPT female, must be factory installed







24/343

22

1 hp Fixed SpeedSubmersible TurbinePump Model Designation


STP XXXXX Y - A - B






ethanol capable.


H = High pressure (46 psideadhead output)

K = Intake filter screen (IFS, factoryinstalled to PMA)*R = Model R check valve (24 psirelief/22 psi reset for PLLD)*W = Model W check valve (16 psirelief/13 psi reset for PPM4000)

*Note: If not otherwise specified, all

STP models supplied withstandard model check valve(40 psi relief/35 psi reset forMLD and TS-LS300).



A = Model Length






Riser pipe length is expressed as twonumeric characters that indicate thetotal length of the riser in inches. Riserpipes are available from 7" to 69" in 1"increments (additional charge forrisers 31" or longer).


Power Requirements

1 hp fixed speed models requiresingle-phase, 208-230 VAC, 60 Hz

incoming power. 1 hp fixed speed models incorporate a

starting and running capacitor, with internalbleed resistor, rated 370 Volt,15 microfarad.

STP-SCI single-phase smart controllers andSTP-CBS single-phase control boxes areavailable for 1 hp pump control.

Max. motor draw: 11 Amps.

Pump Motor

1 hp fixed speed, 3450 rpm, multi-stagecentrifugal type pump motor with integral,automatic, thermal overload protection.

Standard pressure (two-stage) model, max.flow = 100 gpm, max. pressure = 34 psi.

High pressure (H150, three-stage) model,max. flow = 65 gpm, max. pressure =46 psi.

1 hp Fixed Speed Submersible TurbinePump Specifications



Standard models are UL and cUL listed forfuel mixtures containing up to 10% ethanol,and 20% MTBE, 20% ETBE or 17% TAMEwith gasoline.

STPAG models are compatible for fuelmixtures containing up to 85% ethanol or100% biodiesel, and 20% MTBE, 20% ETBEor 17% TAME with gasoline.

1 hp fixed speed models can also be usedwith diesel fuels, fuel oils, kerosene, Avgasand jet fuels in a non-gelled pourable state.


Standard Features

1 hp fixed speed models are available invariable and fixed length options.



Syphon: venturi-type syphon primersupplied with every submersible. Syphoncheck valve and secondary syphonsold separately.



Approvals



Franklin Fueling Systems is an ISO 9001

Certified Manufacturer.


B

A

LU

SYPHON

T

K


25/343


23


1 hp Fixed Speed Turbine Performance Chart

0

10

20

30

40

50

60

70

80

90

100

110

0 20 40 60 80 100 120 140 160 180 200Flow in Gallons per Minute (gpm)


Note: Performance based on pumping solvent (0.78 specific gravity). Pressure is taken at the manifolddischarge outlet. STP150 models are powered by a single-phase, 60 Hz, 208/230 Volt power supply.

Two STP150 Manifolded

1 hp Pumps

One STP150 1 hp Pump

1 hp High Pressure Fixed Speed Turbine Performance Chart

0

10

20

30

40

50

60

70

80

90

100

110

120

130

140

0 20 40 60 80 100 120 140



Note: Performance based on pumping solvent (0.78 specific gravity). Pressure is taken at the manifolddischarge outlet. STPH150 models are powered by a single-phase, 60 Hz, 208/230 Volt power supply.

One STPH150 1 hp

High Pressure Pump

Two STPH150 Manifolded

1 hp High Pressure Pumps


26/343

24



Length RangeNumber

ModelLength*

Range

STP150-VL1 1 hpfixed speed VL1 60"-88"

STP150-VL2 1 hp fixed speed VL2 91"-152"

STP150-VL3 1 hp fixed speed VL3 123"-214"

STPH150-VL1 1 hp high pressure fixed speed VL1 61"-89"



Alcohol-GasolineModel

DescriptionModel

Length RangeNumber

ModelLength*

Range

STPAG150-VL1 1 hp AG fixed speed VL1 60"-88"



STPAGH150-VL1 1 hp AG high pressure fixed speed VL1 61"-89"



1 HP Fixed Speed Submersible Turbine Pumps



F Floating suction adapter, 1" NPT female, must be factory installedK IFS (intake filter screen), factory assembled to pump motor assembly

R Model R check valve , factory installed, for Veeder-Root PLLD Line Leak







402313921 STP-DHI-CBS, combo DHI with factory wired STP-CBS402459931 Model 65 psi check valve (for slave of manifolded STPs with Veeder-Root PLLD)





Field Installed Options(1 hp fixed speed specific accessories)

Notes: 1. STP models are compatible with fuel mixtures containing up to 10% ethanol with gasoline, and 20% MTBE, 20% ETBE or17% TAME with gasoline.STPAG models are compatible with fuel mixtures containing up to 100% biodiesel or 85% ethanol with gasoline, and 20%MTBE, 20% ETBE or 17% TAME with gasoline.

2. All models are supplied with a standard check valve unless factory option R or W is specified.3. All above models require single-phase, 208-230 VAC, 60 Hz incoming power.4. **4" riser pipe, if supplied locally, must be 4" OD by 3/16" WT tubing.


*When purchasing STP-SCI or STP-DHI-SCI in equal quantities offixed speed 4" STPs, the STP-SCI or STP-DHI-SCI will be invoicedat special discount pricing.




27/343


25


1/3 and 3/4 HP FixedSpeed SubmersibleTurbine Pump Model

Designation SystemA typical turbine model designationhas up to five components to definethe pump being supplied as follows:

STP XXXXX Y - A - B






ethanol capable.


K = Intake filter screen (IFS, factoryinstalled to PMA)*R = Model R check valve (24 psirelief/22 psi reset for PLLD)*W = Model W check valve (16 psirelief/13 psi reset for PPM4000)

*Note: If not otherwise specified, allSTP models supplied withstandard model check valve (40

psi relief/35 psi reset for MLDand TS-LS300)


33 = 1/3 hp fixed speed


A = Model Length**







Power Requirements

1/3 and 3/4 hp fixed speed models requiresingle-phase, 208-230 VAC, 60 Hz

incoming power. 1/3 and 3/4 hp fixed speed models

incorporate a starting and runningcapacitor, with internal bleed resistor, rated370 Volt, 15 microfarad.

STP-SCI single-phase smart controllers andSTP-CBS single-phase control boxes areavailable for 1/3 and 3/4 hp pump control.

1/3 hp max. motor draw: 4 Amps.

3/4 hp max. motor draw: 7 Amps.

Pump Motor

1/3 and 3/4 hp fixed speed, 3450 rpm,

two-stage centrifugal type pump motorwith integral, automatic, thermaloverload protection.

1/3 hp models have a max. flow of 40 gpmand a max. pressure of 28 psi.

3/4 hp models have a max. flow of 65 gpmand a max. pressure of 31 psi.

1/3 and 3/4 HP Fixed Speed Submersible TurbinePump Specifications



Standard models are UL and cUL listed forfuel mixtures containing up to 10% ethanol,and 20% MTBE, 20% ETBE or 17% TAMEwith gasoline.

STPAG models are compatible with fuelmixtures containing up to 85% ethanol or100% biodiesel, and 20% MTBE, 20% ETBEor 17% TAME with gasoline.

1/3 and 3/4 hp fixed speed models canalso be used with diesel fuels, fuel oils,kerosene, Avgas and jet fuels in a non-gelledpourable state.

All wetted elastomers are made of a high

grade, fluorocarbon compound.

Standard Features

1/3 and 3/4 hp fixed speed models areavailable in variable and fixedlength options.



Syphon: venturi-type syphon primer

supplied with every submersible.Syphon check valve and secondarysyphon sold separately.



Approvals

Consult factory forapplicable approvals.




B

A

LU

SYPHON

T

K


28/343

26


3/4 hp Fixed Speed Turbine Performance Chart

0

10

20

30

40

50

60

70

80

90

0 20 40 60 80 100 120 140Flow in Gallons per Minute (gpm)



One STP75 3/4 hp Pump


3/4 hp Pumps

1/3 hp Fixed Speed Turbine Performance Chart

0

10

20

30

40

50

60

70

80

90

0 20 40 60 80Flow in Gallons per Minute (gpm)




1/3 hp Pumps

One STP33 1/3 hp Pump


29/343


27



Length RangeNumber

Model Length*

Range

STP33-VL1 1/3 hpfi

xed speed VL1 55"-83"STP33-VL2 1/3 hp fixed speed VL2 86"-147"

STP33-VL3 1/3 hp fixed speed VL3 118"-209"




Alcohol-GasolineModel

DescriptionModel

Length RangeNumber

Model Length*

Range

STPAG33-VL1 1/3 hp AG fixed speed VL1 55"-83"






1/3 and 3/4 HP Fixed Speed Submersible Turbine Pumps












Field Installed Options(1/3 and 3/4 hp fixed speed specific accessories)

Notes: 1. STP models are compatible with fuel mixtures containing up to 10% ethanol with gasoline, and 20% MTBE, 20% ETBE or17% TAME with gasoline.STPAG models are compatible with fuel mixtures containing up to 100% biodiesel or 85% ethanol with gasoline, and 20%MTBE, 20% ETBE or 17% TAME with gasoline.



*When purchasing STP-SCI or STP-DHI-SCI in equal quantities offixed speed 4" STPs, the STP-SCI or STP-DHI-SCI will be invoicedat special discount pricing.




K IFS (intake filter screen), factory assembled to pump motor assembly






30/343

28


Fixed LengthSubmersible TurbinePump Model Designation


STP XXXXX Y - A - B






ethanol capable.


H = High pressure (1 hp and 2 hpmodels only)


M = MagShell (2 hp models only)*R = Model R check valve (24 psirelief/22 psi reset for PLLD)*W = Model W check valve (16 psirelief/13 psi reset for PPM4000)

*Note: If not otherwise specified, allSTP models supplied with standardmodel check valve (40 psi relief/35 psireset for MLD and TS-LS300).






A = Model Length

Model length is expressed as three

numeric characters that indicate thelength of the STP from the turbinemanifold bottom to the pump motorinlet in inches, available from 37" to211" (additional charge for models133" and longer).



Power Requirements

Fixed length, fixed speed models requiresingle-phase, 208-230 VAC, 60 Hzincoming power.

Fixed length, fixed speed models areavailable in 1/3, 3/4, 1 and 2 hp versions.

Fixed length, fixed speed modelsincorporate a starting and running capacitorwith internal bleed resistor.

A 370 Volt, 15 microfarad rated capacitoris used with 1/3, 3/4 and 1 hp fixedlength, fixed speed versions.

A 370 Volt, 40 microfarad rated capacitoris used with 2 hp fixed length, fixedspeed versions.

STP-SCI single-phase smart controllers andSTP-CBS single-phase control boxes areavailable for fixed speed pump control.

Pump Motor

Fixed speed, 3450 rpm, multi-stagecentrifugal type pump motor with integral,automatic, thermal overload protection.

1/3 and 3/4 hp fixed speed models areavailable as two-stage versions.

1 and 2 hp fixed speed models areavailable in standard pressure (two-stage)versions and high pressure (H option,three-stage) versions.

Fixed Length Submersible Turbine Pump Specifications



Fixed length STP models are UL and cULlisted for fuel mixtures containing up to10% ethanol, and 20% MTBE, 20% ETBE or17% TAME with gasoline.

AG (alcohol-gasoline) models arecompatible with fuel mixtures containing upto 85% ethanol or 100% biodiesel, and20% MTBE, 20% ETBE or 17% TAMEwith gasoline.

Fixed length models can also be used withdiesel fuels, fuel oils, kerosene, Avgas and

jet fuels in a non-gelled pourable state.


Standard Features



Syphon: venturi-type syphon primersupplied with every submersible. Syphoncheck valve and secondary syphon soldseparately.



Approvals





B

A

LU

SYPHON

T

K


31/343


29


Model DescriptionModel Length*

Range

STP33 1/3 hp fixed speed 37"-132"

STP75 hp fixed speed 37"-132"STP150 1 hp fixed speed 37"-132"

STPH150 1 hp high pressure fixed speed 37"-132"

STPM200 2 hp fixed speed with MagShell 37"-132"

STPHM200 2 hp high pressure f ixed speed with MagShell 37"-132"

Fixed Length Submersible Turbine Pumps












Field Installed Options(fixed speed specific accessories)

Notes: 1. Remove M from model number for non-MagShell pump motor assembly.2. STP models are compatible with fuel mixtures containing up to 10% ethanol with gasoline, and 20% MTBE, 20% ETBE or

17% TAME with gasoline.STPAG models are compatible with fuel mixtures containing up to 100% biodiesel or 85% ethanol with gasoline, and 20%MTBE, 20% ETBE or 17% TAME with gasoline.


*Model length (A) defined as the dimension from turbine manifold bottom to pump motor inlet. Model length (A) can be a minimumof 37" to a maximum of 211".

*

When purchasing STP-SCI or STP-DHI-SCI in equal quantities offixed speed 4" STPs, the STP-SCI or STP-DHI-SCI will be invoicedat special discount pricing.




K IFS (intake filter screen), factory assembled to pump motor assembly



AG Alcohol-gasoline compatible




32/343

30


Advantages

All models are capable of detectingline leaks equivalent to 3 gph at

10 psi when installed properly withthe appropriate fuels. All models willsignal detection of leaks byrestricting product delivery to lessthan 3 gpm and taking more than 4seconds to open.

All models require 2 to 3 seconds tomake a line test when no line leaksexist and air is purged from pipingbetween the discharge of the MLDand the dispenser solenoid.

All models will remain in the openposition during product delivery tomanifold, with discharge pressures aslow as 1 psi. All models will reset to

tripped when line pressure delay isbelow 3 psi with pump off.

All models will detect leaks up to 10feet above the MLD installation point.

For use with 4" STPs, the MLD product line is precision built, with unique constructionfeatures that provide busy stations with maximum flow rates and long service life. The MLD

is offered in three models to match your exact application, ensuring accurate, nuisance-freeoperation critical to profitable station operation.

Mechanical Line Leak Detector

Specifications:

Three models: STP-MLD (blue) forgasoline, STP-MLD-D (tan) for diesel andSTP-MLD-E (grey) for some expandablepipe applications.

Solid brass piston has 1-5/8" of travel tomove the leak detection poppet fully out ofthe flow, offering minimum flow restrictionand maximum flow rates.

Burnished brass cylinder liner and polishedstainless steel piston rod ensure smoothoperation and long life from the PTFE seal.

Thermal compensation chamber of 5cubic inches helps minimize thermalcontraction nuisance tripping.


Max. liquid viscosity: 70 SSU at 60 F (15 C).

STP-MLD and STP-MLD-E models arecompatible with fuel mixtures containing upto 10% ethanol, and 20% MTBE, 20% ETBEor 17% TAME with gasoline, as well asdiesel fuels, fuel oils, kerosene, Avgas and jetfuels.

STP-MLD-D models are listed for dieselfuels or kerosene only.

BURNISHED BRASSCYLINDER LINER

PTFE SEALBRASS PISTON

THERMAL CONTRACTIONCOMPENSATION CHAMBER

GROUND ANDPOLISHEDSTAINLESS STEELPISTON ROD

PTFE SEAL

Approvals

Third party certified to comply with US EPArequirements 280.41 (B) and 280.44 (A) forcontinuous monitoring of pressurized piping.

Consult factory for otherapplicable approvals.




33/343


3


Mechanical Line Leak Detector(for use with 4" STPs)*

MLD Repair Parts and AccessoriesPart Number Description

400440101 MLD vent tube

400449901 MLD hardware pack, fittings and documentation

400518001 Leak detector adapter tee


400500901 STP-MLD for gasoline, blue400501901 STP-MLD-D for diesel or kerosene, tan

400502901** STP-MLD-E for expandable piping, grey

12.50"

10.65"

SYPHON

LU

TANK PORT(VENT TUBE MUST BECONNECTED HERE)

SYPHON PORT

T

K

3.50"

MLD

LEAK DETECTOR PORT2" NPT

MLD VENT TUBE

Notes: 1. MLD and MLD-E models are compatible with fuel mixtures containing up to 10% ethanol with gasoline, diesel fuels, and20% MTBE, 20% ETBE or 17% TAME with gasoline.

2. MLD-D models are listed for compatibility with diesel fuels and kerosene applications only.3. All above models will only mount in the 2" NPT leak detector port of a 4" submersible turbine, including competitive

models, or in a leak detector adapter tee (sold separately below).*Designed for limited flexible piping systems with low bulk modulus, consult factory before ordering.**Refer to STP-MLD installation manual for complete compatibility specifications.

Single Pack

Three Pack


400500903 STP-MLD for gasoline

400501903 STP-MLD-D for diesel or kerosene

400502903** STP-MLD-E for expandable piping

400503903 COMBO, contains two STP-MLDs and one STP-MLD-D


34/343

32

Submersible Turbine Pump Controllers

Advantages

Easy Retrofit - The STP-SCI iscompatible with single-phase 1/3

through 2 hp STPs from FE Petro orother competitive models. Retrofittingan existing station requires replacingan existing control box with theSTP-SCI and pressing the reset buttonto allow the controller toautomatically learn the electricalcharacteristics of the pump.

History Storage of PumpConditions - The STP-SCIautomatically logs the last fiveabnormal conditions seen in thepumping system. This data isretained in non-volatile memory.Service technicians can then quickly

view a history of abnormalconditions, particularly usefulwhen troubleshootingintermittent conditions.

Designed to replace standard control boxes in both new and existing installations. TheSTP-SCI provides valuable pump protection and performance features never before offered in

one economical controller.

Single-Phase Smart Controller

Feature STP-SCIStandardControl

Box

Dry run protectionwith automatic reset

Yes No

Low voltage detection Yes No

Pump motor failuredetection

Yes No

Open circuit detection Yes No

Extended pump rundetection

Yes No

Slave pump auto startoperation

Yes No

Auto sequencing ofmanifold pump

Yes No

Fault diagnostic lights Yes No

Pump operating light Yes Yes

High voltage surgeprotection

Yes No

Fault history storage Yes No

Power ON light Yes No

External run lightprovision

Yes Yes

Compatible with 1/3through 2 hp

Yes Yes

30 Amp line relay Yes Yes

Specifications: Controller size: 8" 5" 3" (215 mm 127 mm 76 mm).

Relay amperage rating: 30 Amps.

Relay/hook signal voltage: 120/240 Volt.

Compatible with all FE Petro single-phase submersibles and competitive makes.

Approvals



Franklin Fueling Systems is an ISO 9001 Certified Manufacturer.


35/343


33


STP-SCI Single-Phase Smart Controller

Notes: 1. SCI models are compatible with all single-phase FE Petro submersibles and competitive makes.2. One SCI required per submersible. Relay rated for 30 Amps (up to 2 hp).

3. SCI models are not compatible for use in master/slave configurations with STP-SC models.*When purchasing STP-SCI or STP-DHI-SCI in equal quantities offixed speed 4" STPs, the STP-SCI or STP-DHI-SCI will be invoicedat special discount pricing.






STP-SCI Single-Phase Smart Controller Standalone Wiring Diagram

ORANGE

SINGLE-PHASEMOTOR

OVERLOADTHERMAL

PLUGCONNECTOR

OIL FILLED CAPACITOR(WITH BLEED RESISTOR)

DISPENSERHANDLE

SWITCH

Note: See product installation instructions for further details. Wiring must conform to all federal, state and local codes. Control panels

are for non-hazardous indoor use only.

+ G -

L1 L2 M1

SUPPLY & RETURN

M2

HOOK

SW2 SW1

STP-SCI

1 2 3 4 5 6 7 8N

O

SW2 (FACTORY DEFAULTS)

(EXTENDED RUN DETECTED)

1 2 3 4 5 6 7 8NO

SW1

(AUTO RESTART ENABLED)

NOTE: SEE INSTALLATION AND OWNERS MANUAL FOR FURTHER

DETAILS OF SWITCH SETTINGS AND STP-SCI CALIBRATIONPROCESS.

GND GND

RETURN

BLACK

BLACK

110-250 VOLT SUPPLY

RED

RED

INCOMING POWER208-240 VOLTS


36/343

34


Advantages

Optically isolates inputs from upto eight dispensers preventing

damage to dispenser relay boardscaused by cross-phasing.

Prevents electrical feedback betweendispenser hook circuits duringperiods of maintenance and serviceas required by NEC 514-6, 1999 andother international codes.

Can be supplied factory-wired intandem with the FE Petro SmartController or the FE Petrostandard control box.

Eliminates false STP run due tovoltage leakage of multipledispensers connected in parallel.

Fuse-protected output tosubmersible pump controller.

The STP-DHI can retrofit to anyexisting site.

The FE Petro dispenser hook isolation device prevents electrical feedback between dispenserhook circuits as required by most electrical codes.

Dispenser Hook Isolation

Specifications:

Enclosure size: 8" x 5" x 3" (215 mm x 127 mm x 76 mm).

Eight optically isolated inputs from dispenser.

One STP-DHI required per product grade for up to eight dispensers.

STP-DHI: 120 V 30 V A input from supply, eight 120 V 10mA inputs from dispensers.

Output fuse rating: 250 V 1A, fast-acting.

300 Volt surge protection.

Maximum ambient temperature rating: 120 F.

LEDs indicate when source power is applied and dispenser hook signals are present.

Compatible with any submersible pump controller.

Approvals



Franklin Fueling Systems is an ISO 9001 Certified Manufacturer.

STPCONTROL

BOX

1

2

3

4

STPCONTROL

BOX

1

2

3

4

STP-DHI

FROMDISPENSERS

FROMDISPENSERS(UP TO 8PER DHI)

Conventional

STP-DHI


37/343


35


DHI Repair Parts and Accessories

STP-DHI Dispenser Hook Isolation

Notes: 1. DHI models are compatible with FE Petro submersible pump controllers andcompetitive pump controller makes accepting 120 Volt dispenser hook signal.

2. DHI models can be connected together for products with more than eightdispenser handle inputs.

*When purchasing STP-DHI-SCI in equal quantities offixed speed 4" STPs, the STP-DHI-SCIwill be invoiced at special discount pricing.


402312921STP-DHI-SCI combo DHI with factory-wired STP-SCI(when purchased with a 4" STP)*

402312921STP-DHI-SCI, combo DHI with factory-wired STP-SCI(when purchased without a 4" STP)

402313921STP-DHI-CBS, combo DHI with factory-wired STP-CBSsingle-phase control box

5800300100 STP-DHI, isolates up to eight, 120 Volt dispenser handles


223243103 DHI fast-acting fuse, 250 VAC, 1 Amp

223885901 DHI circuit board, 120 Volt dispenser hook signal

DHI with 120 VAC Dispenser Hook Signal Wiring Diagram

RV5

RV5

FUSE, 250 VAC, 1 AMP(FAST-ACTING TYPE)

NEUTRAL WIRE TERMINAL

120 VOLTSUPPLY WIRE TERMINAL

DISPENSER #1 (SUPPLY & NEUTRAL),TYPICAL WIRING FOR ALL DISPENSERS

*Wiring is polarity-sensitive when multiple units are connected together.

* TO ADDITIONAL STP-DHI(S)HOOK OUT TERMINALS

* TO ADDITIONAL STP-DHI(S)POWER SUPPLY & NEUTRALTERMINALS

NEUTRAL

OUTPUT 110V

NEUTRAL

INPUT 110V

STP-DHI-SCI

STP-DHI-CBS


38/343

36


Advantages

Incorporates an ON/OFFlockout switch.

Relay energized with 110 Voltdispenser/hook signal.

Franklin Fueling Systems is an ISO9001 certified manufacturer.

Consult factory forapplicable approvals.

The FE Petro standard single-phase control box latches line power to the submersible whenthe relay is energized by a dispenser signal. Compatible with FE Petro and competitive makes

of single-phase,fi

xed speed submersible turbines up to 2 hp.

Single-Phase Control Box

PartNumber

Description

400818921STP-CBS, single-phasecontrol box, with switchand lockout, 120 Volt coil

402313921STP-DHI-CBS, combodispenser hook isolationwith factory wired STP-CBS

Notes: 1. CBS models are compatible for use on

all single-phase FE Petro submersiblesand competitive makes.

2. One CBS required per submersible, relayrated for 30 Amps up to 2 hp.

3. Incorporates pump ONindicator light.

4. Relay rated for 220 Volt pumps up to 2hp, 30 Amps.

STP-CBS Repair Parts and Accessories

Item Part Number Description

1 400575001 Power switch for CBS and CBBS models

2 400574001 Power switch bracket

3 400158901 Light assembly, 120 Volt

4 400215931 Relay, 30A, 120 Volt coil

5 400278005 Six position terminal strip

6 402410001 CBS terminal strip label

7 400817901 Cover and enclosure

8 400819001 CBS wiring diagram

8

7 7

1 2

5

4

3

6


39/343


37

Submersible Turbine Pump Accessories

Intake Filter Screen

PRIMARYSYPHON

SECONDARYSYPHON


400660901 Intake fil

ffs catalog principal

Documents