15Framo 80

Beam Section TP F 80Group: A410

ApplicationGalvanised hollow-box-section for fabrication of steel frames. Designed for both simple two-dimensional supports and complex volumetric arrangements. Holes designed to receive Self Forming Screw FLS in conjunction with the relevant component.

Technical Data

Mechanical properties shown above take into account perforations.

ApprovalsCE mark (Declaration of performance see www.sikla.com/service/downloads)

Type Weight[kg/m]

Qty.[m]

Partnumber

TP F 80 6.4 6 192539TP F 80/30 4.3 6 113407

Type Section modulus

[cm3 ]

Moment of inertia[cm4 ]

Radius of inertia[cm]

Torsional moment lt

[cm 4 ]

Cross section A

[cm2 ]

TP F 80 Wy: 15.87Wz: 15.87

ly: 63.49lz: 63.49

iy: 2.95iz: 2.95

98.22 7.28

TP F 80/30 Wy: 8.36Wz: 4.03

ly: 33.47lz: 6.05

iy: 2.76iz: 1.17

18.66 4.37

Material: Steel, hcp

Framo 80

Siconnect 15-110/2

015

TP F 80/30

15Framo 80

End Support STA F 80Group: A422

ApplicationPlug-in component designed to create an endplate at the open end of a Beam Section TP F80 or a Cantilever bracket AK F80.

InstallationDepending on the version, following mountings solutions are possible:

Technical Data

ApprovalsCE mark (Declaration of performance see www.sikla.com/service/downloads)MPA tested

Type W[kg]

Quantity[pack]

Partnumber

STA F 80 1.6 1 192856STA F 80-E 1.5 1 192863STA F 80-A 1.7 1 192870

a) With 2x4 Self Forming Screws FLS when used to connect 2 Beam Sections.

b) With 4 Self Forming Screws FLS applied to the octagonal insert and 2 suitable wall anchors/fixings when connected to the building structure.

Type Dimensions of Base plate [mm]

Slots in base plate for

STA F 80 190 x 80 x 8 M10STA F 80-E 165 x 80 x 8 M10STA F 90-A 190 x 80 x 8 M12

Configuration: Base plate welded to octagonal element F 80Material:Plate: Steel, HCPOctagonal element: Steel, HCP

Framo 80

Siconnect 15-110/2

015

STA F 80

STA F 80-E

STA F 80-A

11High Corrosion Protected Products

Channel Connector SK-L HCPGroup: 1853

ApplicationElement for connecting Channels. The multiple bearing of the Channel is to be secured. The Channel Connector should not to be used between the last two bearing points. In combination with Channels > 41/21 the admissible limit has to be respected.

InstallationPosition the Channel Connector on the back of the channel and bolt together the channel ends (through the channel slots) by means of each two Self Forming Screws FLS F 80.

Technical Data

Type For channel Channel heighthmax [mm]

Overall length [mm]

W[kg]

Quantity[pack]

Partnumber

SK-L 41 62 180 0.36 10 198971

Max. adm. limit/ flexion: 300 NmMaterial: Steel S235 JR, HCP

High Corrosion Protected Products

Siconnect 11-110/2

015

16Framo 100

Self Forming Screw FLSGroup: A430

ApplicationThe Self Forming Screw FLS creates its own thread inside the wall of the Framo pilot hole. During the screw-driving operation, the base steel is re-shaped and hardened to form an air-tight seal between the threads of the screw and the surrounding steel, making it exceptionally resistant to vibrational loosening and increasing fastening strength.

Technical Data

ApprovalsMPA tested

Type W[kg]

Quantity[pack]

Partnumber

FLS F 0.03 100 192512

Application Tightening torque[Nm]

System Framo 60Connection to Channels MS 41 35

Material: Steel, HCP

Framo 100

Siconnect 16-110/2

015

2Construction Components

End Clip PV 1-EGroup: E314

ApplicationEdge fastening and assembly block for all typical framed Photovoltaic panels to be used with high loads caused by wind suction. Suits panel thicknesses of 35 - 50 mm for any angle. Bimetal corrosion restistance, by using seal-coating on the support (washer and sleeve). Clamping forces applied at outer edge of panel to prevent undue tensioning of glass.

Scope of deliveryFully assembled unit comprising Speed Nut, Support and Clip.

InstallationInsert Speed Nut into the open channel slot at any position required.Adjust the clip to the panel and tighten it with max. 10 Nm.

Technical Data

Type Panelthickness

[mm]

W[kg]

Quantity[pack]

Partnumber

PV 1-E 35 - 50 0.11 50 199503

adm. shear force 90° to panel surface: 0.5 kN/clipadm. tensile load: 3.2 kN/clipMaterial:Clip: AluminiumScrew: Stainless steel 304Stud bolt, Washer and Speed Nut: HCP

Construction Components

Solar Panel Support System 2-110/2

015

2Construction Components

Middle Clip PV 1-MGroup: E314

ApplicationMiddle fastening and assembly block for all typical framed Photovoltaic panels to be used with high loads caused by wind suction. Suits panel thicknesses (H) of 35 - 50 mm for any angle. Bimetal corrosion resistance, by using seal-coating on the support (washer and sleeve). Clamping forces applied at outer edge of panel to prevent undue tensioning of glass.

Scope of deliveryFully assembled unit comprising Speed Nut, Support and Clip. No loose parts.

InstallationFix Middle Clip into the required position by pressing the Speed Nut into the channel. Slide the Middle Clip along the channel so that it grips onto the existing PV panel already in position. Put the next panel on the frame and tighten the Middle Clip with max 10 Nm.

Technical Data

Type Panelthickness

[mm]

W[kg]

Quantity[pack]

Partnumber

PV 1-M 35 - 50 0.09 50 199510

adm. shear force 90° to panel surface: 1.0 kN/clipadm. tensile load: 3.2 kN/clipMaterial:Clip: AluminiumScrew: Stainless steel 304Stud bolt, Washer and Speed Nut: HCP

Construction Components

Solar Panel Support System 2-110/2

015

2Pressix CC 41 - Assembly System

End Cap ADK 41Group: 1304

ApplicationTo be used for safely and neatly covering the ends of Sikla Channels. Double channels require 2 End Caps.

Technical Data

Type For channel W[kg]

Quantity[pack]

Partnumber

41/21 41/21/1.5 und 41/21/2.5 0.01 100 10103741/31 0.01 100 11047741/41 41/41/1.8 und 41/41/2.5 0.01 100 17768941/45 41/45/3.0 0.01 100 10881241/52 41/52/3.0 0.01 50 17769841/62 41/62/3.0 0.01 50 15320141-75/65 41-75/65/3.0 0.01 50 17770741-75/75 41-75/75/3.0 0.02 50 177716

Material: HD-PE, yellow

Pressix CC 41 - Assembly System

Siconnect 2-110/2

015

15Framo 80

End Cap ADK F 80Group: A430

ApplicationPlastic end cap to close cut ends of Beam Section F80 to meet both visual and health & safety requirements. Standard Cantilever- and Beam Brackets (AK F80 and TKO F80) already include this end cap.

InstallationMallet required.

Technical Data

Type W[kg]

Quantity[pack]

Partnumber

ADK F 80 0.03 25 192674ADK F 80/30 0.02 25 113067

Material: PE, yellow

Framo 80

Siconnect 15-110/2

015

ADK F 80/30

2Construction Components

Channel MS 41 HCPGroup: 1811

ApplicationElement for easily and efficiently pre-assembling crossbars, wall brackets and supporting structures on construction sites or in workshops.

Scope of deliveryAvailable as single or double channels.Double channels are joined together by clinching.

InstallationAll Channels MS 41 hcp are serrated inside and provide numerous combination options with other high corrosion protected system components.

Technical Data

D = Double channel

Approvals

Material: Steel, HCP

TypeW/H/th [mm]

Section modulus[cm3 ]

Moment of inertia[cm4 ]

Radius of gyration[cm]

41/21/2.0 Wy : 0.82Wz : 2.12

ly : 0.92lz : 4.35

iy : 0.76iz : 1.65

41/31/2.0 Wy : 1.60Wz : 2.88

ly : 2.77lz : 5.90

iy : 1.13iz : 1.65

41/41/2.0 Wy : 2.43Wz : 3.65

ly : 5.16lz : 7.48

iy : 1.46iz : 1.75

41/41/2.5 Wy : 2.96Wz : 4.41

ly : 6.19lz : 9.05

iy : 1.43iz : 1.72

41/62/2.5 Wy : 5.54Wz : 6.27

ly : 17.70lz : 12.86

iy : 2.10iz : 1.79

41-75/75/3.0 Wy : 10.31Wz : 11.59

ly : 44.42lz : 43.48

iy : 2.53iz : 2.50

41/21/2.0 D Wy : 2.35Wz : 4.24

ly : 4.93lz : 8.70

iy : 1.24iz : 1.65

41/41/2.5 D Wy : 9.02Wz : 8.82

ly : 36.99lz : 18.10

iy : 2.46iz : 1.72

41-75/75/3.0 D Wy : 30.72Wz : 23.07

ly : 230.40lz : 86.96

iy : 4.07iz : 2.50

TypeW/H/th [mm]

Cross sectionA

[cm2 ]

Distancee

[cm]

Max. point carrying capacity

Fmax [kN]

Max. torsionalmomentMq [Nm]

41/21/2.0 1.61 1.12 4.0 44.541/31/2.0 2.17 1.73 4.0 44.541/41/2.0 2.43 2.12 4.0 44.541/41/2.5 3.05 2.09 6.0 44.541/62/2.5 4.01 3.20 6.0 44.541-75/75/3.0 6.95 4.31 10.0 44.5

41/21/2.0 D 3.21 2.10 4.0 44.541/41/2.5 D 6.09 4.10 6.0 44.541-75/75/3.0 D 13.90 7.50 10.0 44.5

Notice: All values take into account the perforation of the channels. For load charts, see chapter "Pressix CC 41".

Construction Components

Solar Panel Support System 2-110/2

015

41/21/2,0

41/412,5

41-75/75/3.0

* = no RAL quality label

Construction Components

Type Length [m]

Slot pattern Weight[kg/m]

Qty.[m]

Partnumber

41/21/2.0 6 3 1.32 6 19386041/31/2.0 6 3 1.64 6 19889641/41/2.0 6 3 1.97 6 19672441/41/2.5 6 3 2.36 6 16149741/62/2.5 6 3 3.13 6 19952741-75/75/3.0 6 4 5.68 6 174008

41/21/2.0 D * 6 3 2.64 6 19388441/41/2.5 D * 6 3 4.74 6 16674841-75/75/3.0 D * 6 4 11.24 6 173981

Solar Panel Support System 2-2

This product is has obtained the "RAL Gütezeichen Rohrbefestigung" and is subject to external surveillance according to RAL GZ-655.

10/2

015