geometric dimensioning & tolerancing.ppt

Based on the ASME Y14.5M-1994Based on the ASME Y14.5M-1994

Geometric Dimensioning and Tolerancing

Tolerances of Form

Straightness Flatness

Circularity Cylindricity

(ASME Y14.5M-1994, 6.4.1)

(ASME Y14.5M-1994, 6.4.3)

(ASME Y14.5M-1994, 6.4.2)

(ASME Y14.5M-1994, 6.4.4)

25 +/-0.25

0.1 Tolerance

0.5 Tolerance

Straightness is the condition where an element of a surface or an axis is a straight line

Straightness (Flat Surfaces)

0.5 0.1

Straightness (Flat Surfaces)

24.75 min25.25 max

0.5 Tolerance Zone

0.1 Tolerance Zone

The straightness tolerance is applied in the view where the elements to be controlled are represented by a straight line

In this example each line element of the surface must lie within a tolerance zone defined by two parallel lines separated by the specified tolerance value applied to each view. All points on the surface must lie within the limits of size and the applicable straightness limit.

Straightness (Surface Elements)

MMC

0.1 Tolerance Zone

0.1

MMC

0.1 Tolerance Zone

MMC

0.1 Tolerance Zone

In this example each longitudinal element of the surface must lie within a tolerance zone defined by two parallel lines separated by the specified tolerance value. The feature must be within the limits of size and the boundary of perfect form at MMC. Any barreling or waisting of the feature must not exceed the size limits of the feature.

Straightness (RFS)

0.1

Outer Boundary (Max)

MMC

0.1 Diameter Tolerance Zone

Outer Boundary = Actual Feature Size + Straightness Tolerance

In this example the derived median line of the feature’s actual local size must lie within a tolerance zone defined by a cylinder whose diameter is equal to the specified tolerance value regardless of the feature size. Each circular element of the feature must be within the specified limits of size. However, the boundary of perfect form at MMC can be violated up to the maximum outer boundary or virtual condition diameter.

Straightness (MMC)15 14.85

15.1 Virtual Condition

15 (MMC)


15.1 Virtual Condition

14.85 (LMC)


Virtual Condition = MMC Feature Size + Straightness Tolerance

In this example the derived median line of the feature’s actual local size must lie within a tolerance zone defined by a cylinder whose diameter is equal to the specified tolerance value at MMC. As each circular element of the feature departs from MMC, the diameter of the tolerance cylinder is allowed to increase by an amount equal to the departure from the local MMC size. Each circular element of the feature must be within the specified limits of size. However, the boundary of perfect form at MMC can be violated up to the virtual condition diameter.

0.1 M

Flatness

Flatness is the condition of a surface having all elements in one plane. Flatness must fall within the limits of size. The flatness tolerance must be less than the size tolerance.

25 +/-0.25

24.75 min25.25 max

0.1

0.1 Tolerance Zone

0.1 Tolerance Zone

In this example the entire surface must lie within a tolerance zone defined by two parallel planes separated by the specified tolerance value. All points on the surface must lie within the limits of size and the flatness limit.

Circularity is the condition of a surface where all points of the surface intersected by any plane perpendicular to a common axis are equidistant from that axis. The circularity tolerance must be less than the size tolerance

90

90

0.1

0.1 Wide Tolerance Zone

Circularity (Roundness)

In this example each circular element of the surface must lie within a tolerance zone defined by two concentric circles separated by the specified tolerance value. All points on the surface must lie within the limits of size and the circularity limit.

0.1

Cylindricity

Cylindricity is the condition of a surface of revolution in which all points are equidistant from a common axis. Cylindricity is a composite control of form which includes circularity (roundness), straightness, and taper of a cylindrical feature.

0.1 Tolerance Zone

MMC

0.1

In this example the entire surface must lie within a tolerance zone defined by two concentric cylinders separated by the specified tolerance value. All points on the surface must lie within the limits of size and the cylindricity limit.

Tolerances of Orientation

Angularity

Perpendicularity

Parallelism

(ASME Y14.5M-1994 ,6.6.2)

(ASME Y14.5M-1994 ,6.6.4)

(ASME Y14.5M-1994 ,6.6.3)

Angularity (Feature Surface to Datum Surface)

Angularity is the condition of the planar feature surface at a specified angle (other than 90 degrees) to the datum reference plane, within the specified tolerance zone.

A

20 +/-0.5

30 o

A

19.5 min

0.3 Wide Tolerance

Zone

30 o

A

20.5 max

0.3 Wide Tolerance

Zone

30 o

The tolerance zone in this example is defined by two parallel planes oriented at the specified angle to the datum reference plane.

0.3 A

Angularity is the condition of the feature axis at a specified angle (other than 90 degrees) to the datum reference plane, within the specified tolerance zone.

A

0.3 A

A

60 o

The tolerance zone in this example is defined by a cylinder equal to the length of the feature, oriented at the specified angle to the datum reference plane.

0.3 Circular Tolerance Zone


Angularity (Feature Axis to Datum Surface)

NOTE: Tolerance applies to feature at RFS



Angularity is the condition of the feature axis at a specified angle (other than 90 degrees) to the datum reference axis, within the specified tolerance zone.


A

Datum Axis A

Angularity (Feature Axis to Datum Axis)

The tolerance zone in this example is defined by a cylinder equal to the length of the feature, oriented at the specified angle to the datum reference axis.

NOTE: Feature axis must lie within tolerance zone cylinder

0.3 A

o45

0.3 A

A


A A

Perpendicularity is the condition of the planar feature surface at a right angle to the datum reference plane, within the specified tolerance zone.

Perpendicularity (Feature Surface to Datum Surface)


The tolerance zone in this example is defined by two parallel planes oriented perpendicular to the datum reference plane.

C

Perpendicularity is the condition of the feature axis at a right angle to the datum reference plane, within the specified tolerance zone.

Perpendicularity (Feature Axis to Datum Surface)

0.3 C





The tolerance zone in this example is defined by a cylinder equal to the length of the feature, oriented perpendicular to the datum reference plane.

Perpendicularity (Feature Axis to Datum Axis)


The tolerance zone in this example is defined by two parallel planes oriented perpendicular to the datum reference axis.

Perpendicularity is the condition of the feature axis at a right angle to the datum reference axis, within the specified tolerance zone.


A

Datum Axis A

0.3 A

0.3 A

A

25 +/-0.5

25.5 max


A

24.5 min


A

Parallelism is the condition of the planar feature surface equidistant at all points from the datum reference plane, within the specified tolerance zone.

Parallelism (Feature Surface to Datum Surface)

The tolerance zone in this example is defined by two parallel planes oriented parallel to the datum reference plane.

A


Parallelism (Feature Axis to Datum Surface)

0.3 A

A

NOTE: The specified tolerance does not apply to the orientation of the feature axis in this direction

Parallelism is the condition of the feature axis equidistant along its length from the datum reference plane, within the specified tolerance zone.

The tolerance zone in this example is defined by two parallel planes oriented parallel to the datum reference plane.


A

B

Parallelism (Feature Axis to Datum Surfaces)

A

B




Parallelism is the condition of the feature axis equidistant along its length from the two datum reference planes, within the specified tolerance zone.

The tolerance zone in this example is defined by a cylinder equal to the length of the feature, oriented parallel to the datum reference planes.


0.3 A B

Parallelism (Feature Axis to Datum Axis)

Parallelism is the condition of the feature axis equidistant along its length from the datum reference axis, within the specified tolerance zone.

A

0.1 A



Datum Axis A

The tolerance zone in this example is defined by a cylinder equal to the length of the feature, oriented parallel to the datum reference axis.


Tolerances of Profile

Profile of a Line

Profile of a Surface

(ASME Y14.5M-1994, 6.5.2b)

(ASME Y14.5M-1994, 6.5.2a)

18 Max

Profile of a Line

2 Wide Size Tolerance Zone

1 A B C

A

17 +/- 1

1 Wide Profile Tolerance Zone

C

A1

20 X 20

A2

20 X 20

A3

20 X 20

B

The profile tolerance zone in this example is defined by two parallel lines oriented with respect to the datum reference frame. The profile tolerance zone is free to float within the larger size tolerance and applies only to the form and orientation of any individual line element along the entire surface.

Profile of a Line is a two-dimensional tolerance that can be applied to a part feature in situations where the control of the entire feature surface as a single entity is not required or desired. The tolerance applies to the line element of the surface at each individual cross section indicated on the drawing.

16 Min.

Profile of a Surface is a three-dimensional tolerance that can be applied to a part feature in situations where the control of the entire feature surface as a single entity is desired. The tolerance applies to the entire surface and can be used to control size, location, form and/or orientation of a feature surface.


2 Wide Tolerance Zone Size, Form and Orientation

A

A1

20 X 20

A2

20 X 20

A3

20 X 20

C 2 A B C

23.5

23.5Nominal Location

The profile tolerance zone in this example is defined by two parallel planes oriented with respect to the datum reference frame. The profile tolerance zone is located and aligned in a way that enables the part surface to vary equally about the true profile of the feature.

B


A1

20 X 20

A2

20 X 20

A3

20 X 20

B

C

50

B

C

50

1 Wide Total Tolerance Zone

(Bilateral Tolerance)

The tolerance zone in this example is defined by two parallel planes oriented with respect to the datum reference frame. The profile tolerance zone is located and aligned in a way that enables the part surface to vary equally about the true profile of the trim.

1 A B C

Nominal Location

0.5 Inboard

0.5 Outboard

Profile of a Surface when applied to trim edges of sheet metal parts will control the location, form and orientation of the entire trimmed surface. When a bilateral value is specified, the tolerance zone allows the trim edge variation and/or locational error to be on both sides of the true profile. The tolerance applies to the entire edge surface.


A1

20 X 20

A2

20 X 20

A3

20 X 20

B

C

50

B

C

50

0.5 Wide Total Tolerance Zone

(Unilateral Tolerance)

Profile of a Surface when applied to trim edges of sheet metal parts will control the location, form and orientation of the entire trimmed surface. When a unilateral value is specified, the tolerance zone limits the trim edge variation and/or locational error to one side of the true profile. The tolerance applies to the entire edge surface.

The tolerance zone in this example is defined by two parallel planes oriented with respect to the datum reference frame. The profile tolerance zone is located and aligned in a way that allows the trim surface to vary from the true profile only in the inboard direction.

0.5 A B C

Nominal Location


A1

20 X 20

A2

20 X 20

A3

20 X 20

B

C

50

1.2 A B C

B

C

50

0.5 Inboard

0.7 Outboard

1.2 Wide Total Tolerance Zone

(Unequal Bilateral Tolerance)

Profile of a Surface when applied to trim edges of sheet metal parts will control the location, form and orientation of the entire trimmed surface. Typically when unequal values are specified, the tolerance zone will represent the actual measured trim edge variation and/or locational error. The tolerance applies to the entire edge surface.

The tolerance zone in this example is defined by two parallel planes oriented with respect to the datum reference frame. The profile tolerance zone is located and aligned in a way that enables the part surface to vary from the true profile more in one direction (outboard) than in the other (inboard).

0.5

Nominal Location

A

25

A0.50.1

25.2524.75


A

Composite Profile of Two Coplanar Surfaces w/o Orientation Refinement


Form Only

Location & Orientation



25.25

24.75

A

A

A

25

A0.5A0.1 Form & Orientation

Composite Profile of Two Coplanar Surfaces With Orientation Refinement


Location

Tolerances of Location

True Position

Concentricity

Symmetry

(ASME Y14.5M-1994, 5.2)

(ASME Y14.5M-1994, 5.12)

(ASME Y14.5M-1994, 5.13)

10.25 +/- 0.5

10.25 +/- 0.5

8.5 +/- 0.1

RectangularTolerance Zone

10.25

10.25

8.5 +/- 0.1

Circular Tolerance Zone

B

A

C

Coordinate vs GeometricTolerancing Methods

Coordinate Dimensioning Geometric Dimensioning

Rectangular Tolerance Zone Circular Tolerance Zone

1.4+/- 0.5

+/- 0.5

57% LargerTolerance Zone

Circular Tolerance Zone

Rectangular Tolerance Zone

Increased Effective Tolerance

1.4 A B C

Formula to determine the actual radial position of a feature using measured coordinate values (RFS)

Z positional tolerance /2

X2 Y2+Z =

X =2

Y =2

X

Y

Z Feature axis actual location (measured)

Positional tolerance zone cylinder

Feature axis true position (designed)

Positional Tolerance Verification

Z = total radial deviation

“X” measured deviation

“Y” measured deviation

Actual feature boundary

(Applies when a circular tolerance is indicated)

Formula to determine the actual radial position of a feature using measured coordinate values (MMC)

Z

X2 Y2+Z =

X =2

Y =2

X

Y

Z Feature axis actual location (measured)

Positional tolerance zone cylinder

Feature axis true position (designed)

Positional Tolerance Verification

Z = total radial deviation“X” measured deviation“Y” measured deviation

Actual feature boundary

+( actual - MMC)2

= positional tolerance

(Applies when a circular tolerance is indicated)

Bi-directional True PositionRectangular Coordinate Method

3510

10

AC

B

1.5 A B C

0.5 A B C2X

2X

10 35

1.5 WideTolerance

Zone

0.5 WideTolerance Zone

True Position Relatedto Datum Reference Frame

10B

C

Each axis must lie within the 1.5 X 0.5 rectangular tolerance zone basically located to the datum reference frame

As Shownon Drawing

Means This:

2X 6 +/-0.25

Bi-directional True PositionMultiple Single-Segment Method

3510

10

AC

B

10 35

1.5 WideTolerance

Zone

0.5 WideTolerance Zone

True Position Relatedto Datum Reference Frame

10B

C

Each axis must lie within the 1.5 X 0.5 rectangular tolerance zone basically located to the datum reference frame

As Shownon Drawing

Means This:

2X 6 +/-0.251.5 A B C0.5 A B

3510

10

AC

B As Shownon Drawing

Means This:

1.5 A B C 0.5 A B CBOUNDARY BOUNDARY

10 3510

B

C

2X 13 +/-0.25 2X 6 +/-0.25

12.75 MMC width of slot-1.50 Position tolerance

11.25 Maximum boundary

Both holes must be within the size limits and no portion of their surfaces may lie within the area described by the 11.25 x 5.25 maximum boundaries when the part is positioned with respect to the datum reference frame. Theboundary concept can only be applied on anMMC basis.

o90

True position boundary relatedto datum reference frame

A

Bi-directional True PositionNoncylndrical Features (Boundary Concept)

MM

5.75 MMC length of slot-0.50 Position tolerance

5.25 maximum boundary

Composite True PositionWithout Pattern Orientation Control

3510

10

AC

B

10 35

True Position Relatedto Datum ReferenceFrame

10B

C

Each axis must lie within each tolerance zone simultaneously

As Shownon Drawing

Means This:

2X 6 +/-0.251.5 A B C0.5 A

0.5 Feature-RelatingTolerance Zone Cylinder

1.5 Pattern-LocatingTolerance Zone Cylinder

pattern location relative to Datums A, B, and Cpattern orientation relative to

Datum A only (perpendicularity)

Composite True PositionWith Pattern Orientation Control

3510

10

AC

B

10 35

True Position Relatedto Datum ReferenceFrame

10B

C

Each axis must lie within each tolerance zone simultaneously

As Shownon Drawing

Means This:

2X 6 +/-0.25

0.5 Feature-RelatingTolerance Zone Cylinder

1.5 Pattern-LocatingTolerance Zone Cylinder

pattern location relative to Datums A, B, and C

pattern orientation relative to Datums A and B

1.5 A B C0.5 A B

Location (Concentricity)Datum Features at RFS

A

15.9515.90

As Shown on Drawing

Derived Median Points of Diametrically Opposed Elements

Axis of DatumFeature A

Means This:

Within the limits of size and regardless of feature size, all median points of diametrically opposed elements must lie within a 0.5 cylindrical tolerance zone. The axis of the tolerance zone coincides with the axis of datum feature A. Concentricity can only be applied on an RFS basis.

0.5 A6.35 +/- 0.05

0.5 Coaxial Tolerance Zone

Location (Symmetry)Datum Features at RFS

A

15.9515.90

0.5 A6.35 +/- 0.05

Derived MedianPoints

Center Plane of Datum Feature A


Means This:

Within the limits of size and regardless of feature size, all median points of opposed elements must lie between two parallel planes equally disposed about datum plane A, 0.5 apart. Symmetry can only be applied on an RFS basis.

As Shown on Drawing

Tolerances of Runout

Circular Runout

(ASME Y14.5M-1994, 6.7.1.2.1)

Total Runout(ASME Y14.5M-1994 ,6.7.1.2.2)

Datum feature

Datum axis (established from datum feature

Angled surfaces constructed around a datum axis

External surfaces constructed around a datum axis

Internal surfaces constructed around a datum axis

Surfaces constructed perpendicular to a datum axis

Features Applicable to Runout Tolerancing

0+ -

Full Indicator Movement

Maximum Minimum

Total Tolerance

Maximum Reading

Minimum Reading

Full Part Rotation

Measuring position #1 (circular element #1)

Circular Runout

When measuring circular runout, the indicator must be reset to zero at each measuring position along the feature surface. Each individual circular element of the surface is independently allowed the full specified tolerance. In this example, circular runout can be used to detect 2-dimensional wobble (orientation) and waviness (form), but not 3-dimensional characteristics such as surface profile (overall form) or surface wobble (overall orientation).

Measuring position #2 (circular element #2)

Circular runout can only be applied on an RFS basis and cannot be modified to MMC or LMC.

o360 Part Rotation

50 +/- 2o o

As Shownon Drawing

Means This:

Datum axis A

Single circular element

Circular Runout (Angled Surface to Datum Axis)

0.75 A

A

50 +/-0.25

0+-

NOTE: Circular runout in this example only controls the 2-dimensional circular elements (circularity and coaxiality) of the angled feature surface not the entire angled feature surface

Full Indicator Movement( )

The tolerance zone for any individual circular element is equal to the total allowable movement of a dial indicator fixed in a position normal to the true geometric shape of the feature surface when the part is rotated 360 degrees about the datum axis. The tolerance limit is applied independently to each individual measuring position along the feature surface.

Allowable indicator reading = 0.75 max.

When measuring circular runout, the indicator must be reset when repositioned along the feature surface.

Collet or Chuck

As Shownon Drawing

50 +/-0.25

0.75 A

Circular Runout (Surface Perpendicular to Datum Axis)

o360 Part Rotation

0+-

Datum axis A


NOTE: Circular runout in this example will only control variation in the 2-dimensional circular elements of the planar surface (wobble and waviness) not the entire feature surface


Means This:



A

0+ -



o360 Part Rotation

Means This:

As Shownon Drawing

50 +/-0.25

0.75 A

Datum axis A


Circular Runout (Surface Coaxial to Datum Axis)


NOTE: Circular runout in this example will only control variation in the 2-dimensional circular elements of the surface (circularity and coaxiality) not the entire feature surface

A

0+ -



o360 Part Rotation

Means This:

As Shownon Drawing

0.75 A-B

Datum axis A-B


Circular Runout (Surface Coaxial to Datum Axis)


NOTE: Circular runout in this example will only control variation in the 2-dimensional circular elements of the surface (circularity and coaxiality) not the entire feature surface

Machine center

Machine center

BA

As Shownon Drawing

50 +/-0.25

Circular Runout (Surface Related to Datum Surface and Axis)

o360 Part Rotation

0+ -

Datum axis B


The tolerance zone for any individual circular element is equal to the total allowable movement of a dial indicator fixed in a position normal to the true geometric shape of the feature surface when the part is located against the datum surface and rotated 360 degrees about the datum axis. The tolerance limit is applied independently to each individual measuring position along the feature surface.

Means This:

A



Collet or Chuck

Stop collar

0.75 A B

Datum plane A

B

0+

Full Indicator Movement

Total Tolerance

Maximum Reading

Minimum Reading

Full Part Rotation

-

0+ -

Total Runout

Maximum Minimum

When measuring total runout, the indicator is moved in a straight line along the feature surface while the part is rotated about the datum axis. It is also acceptable to measure total runout by evaluating an appropriate number of individual circular elements along the surface while the part is rotated about the datum axis. Because the tolerance value is applied to the entire surface, the indicator must not be reset to zero when moved to each measuring position. In this example, total runout can be used to measure surface profile (overall form) and surface wobble (overall orientation).

Indicator Path

Total runout can only be applied on an RFS basis and cannot be modified to MMC or LMC.

Full Part Rotation

50 +/- 2o o

As Shownon Drawing

A

50 +/-0.25

0.75 A

Means This:

Datum axis A

0+-

The tolerance zone for the entire angled surface is equal to the total allowable movement of a dial indicator positioned normal to the true geometric shape of the feature surface when the part is rotated about the datum axis and the indicator is moved along the entire length of the feature surface.0

+-

NOTE: Unlike circular runout, the use of total runout will provide 3-dimensional composite control of the cumulative variations of circularity, coaxiality, angularity, taper and profile of the angled surface

Total Runout (Angled Surface to Datum Axis)

Collet or Chuck

When measuring total runout, the indicator must not be reset when repositioned along the feature surface.

(applies to the entire feature surface)Allowable indicator reading = 0.75 max.

0+-

Total Runout (Surface Perpendicular to Datum Axis)

As Shownon Drawing

A

50 +/-0.25

0.75 A

35

10

0+-

Datum axis AFull Part Rotation

35

10

Means This:

NOTE: The use of total runout in this example will provide composite control of the cumulative variations of perpendicularity (wobble) and flatness (concavity or convexity) of the feature surface.

The tolerance zone for the portion of the feature surface indicated is equal to the total allowable movement of a dial indicator positioned normal to the true geometric shape of the feature surface when the part is rotated about the datum axis and the indicator is moved along the portion of the feature surface within the area described by the basic dimensions.

When measuring total runout, the indicator must not be reset when repositioned along the feature surface.

(applies to portion of feature surface indicated)Allowable indicator reading = 0.75 max.

Virtual andResultantCondition

BoundariesInternal and External

Features (MMC Concept)

Virtual Condition BoundaryInternal Feature (MMC Concept)

12.5 Virtual Condition Boundary

13.5 MMC Size of Feature1 Applicable Geometric Tolerance

Calculating Virtual Condition

1 A B CM

14 +/- 0.5

C

B XX.X

XX.X

A

As Shown on Drawing

Axis Location of MMC Hole Shown at Extreme Limit

Boundary of MMC HoleShown at Extreme Limit

1 Positional Tolerance Zone at

MMC

True (Basic)Position of Hole


Other PossibleExtreme Locations

Virtual ConditionInner Boundary

Maximum InscribedDiameter( )

Resultant Condition BoundaryInternal Feature (MMC Concept)

1 A B CM

14 +/- 0.5

C

B XX.X

XX.X

A

16.5 Resultant Condition Boundary

14.5 LMC Size of Feature2 Geometric Tolerance (at LMC)

Calculating Resultant Condition (Internal Feature)

As Shown on Drawing

Axis Location of LMC Hole Shown at Extreme Limit

Boundary of LMC HoleShown at Extreme Limit


LMC




Resultant ConditionOuter Boundary

Minimum CircumscribedDiameter( )

Virtual Condition BoundaryExternal Feature (MMC Concept)

15.5 Virtual Condition Boundary

14.5 MMC Size of Feature1 Applicable Geometric Tolerance

Calculating Virtual Condition

1 A B CM

14 +/- 0.5

C

B XX.X

XX.XX

A

As Shown on Drawing

Axis Location of MMC Feature Shown at Extreme Limit

Boundary of MMC FeatureShown at Extreme Limit


MMC

True (Basic)Position of Feature



Virtual ConditionOuter Boundary

Minimum CircumscribedDiameter( )

Resultant Condition BoundaryExternal Feature (MMC Concept)

1 A B CM

14 +/- 0.5

C

B XX.X

XX.X

A

11.5 Resultant Condition Boundary

13.5 LMC Size of Feature2 Geometric Tolerance (at LMC)

Calculating Resultant Condition (External Feature)

As Shown on Drawing

Axis Location of LMC Feature Shown at Extreme Limit

Boundary of LMC featureShown at Extreme Limit


LMC




Resultant ConditionInner Boundary

Maximum InscribedDiameter( )

Extreme Variations of Form Allowed By Size Tolerance

25.1 25

25 (MMC)

25.1 (LMC)

25.1 (LMC)

25 (MMC)

25.1 (LMC)

MMC Perfect Form Boundary

Internal Feature of Size


25 24.9

25 (MMC) 24.9

(LMC)

24.9 (LMC)


25 (MMC)

24.9 (LMC)

External Feature of Size


25.1 25

25 24.9

25 (MMC)

25.1 (LMC)

25.1 (LMC)

25 (MMC) 24.9

(LMC)

24.9 (LMC)

25 (MMC)

25.1 (LMC)


25 (MMC)

24.9 (LMC)

------------- and _------------------------------ are individual line or circularelement (2-D) controls.

Form Control Quiz

The four form controls are -----------, ------------- ,

-----------, and -----------Rule #1 states that unless otherwise specified a feature of

size must have ---------------- at MMC.

------------- and ------------- are surface (3-D) controls.

Circularity can be applied to both ------------- and ------------- cylindrical parts.

1.

2.

3.

4.

5.

Form controls require a datum reference. F

Form controls do not directly control a feature’s size.

A feature’s form tolerance must be less than it’s sizetolerance. T

Flatness controls the orientation of a feature. F

Size limits implicitly control a feature’s form. T

6.

7.

8.

9.

10.

Questions #1-5 Fill in blanks (choose from below)

straightnessflatness

circularity

cylindricity

perfect formstraight tapered profile

true position

angularity

Answer questions #6-10 True or False

Orientation Control Quiz

The three orientation controls are -------------, ------------- and -------------

1.

2.

3.

4.

5.

A ------------- , is always required when applying any ofthe orientation controls.

-------------, is the appropriate geometric tolerance whencontrolling the orientation of a feature at right angles to a datumreference.

Orientation tolerances indirectly control a feature’s form. T

Mathematically all three orientation tolerances are -------------,

Orientation tolerances do not control the -------------, of a feature.

6.

Orientation tolerance zones can be cylindrical. F

Parallelism tolerances do not apply to features of size. T

To apply an angularity tolerance the desired angle mustbe indicated as a basic dimension. T

7.

8.

9.

10.

To apply a perpendicularity tolerance the desired anglemust be indicated as a basic dimension. T


angularity

perpendicularity

parallelism

datum reference

identicallocation

profiledatum feature

datum target

Answer questions #6-10 or False

6.

Profile Control Quiz

Profile tolerances always require a datum reference.


1.

Profile of a surface tolerance is a 2-dimensional control.

Profile of a line tolerances should be applied at MMC.

Profile tolerances can be applied to features of size.

2.

3.

4.

5.

Profile of a surface tolerance should be used to controltrim edges on sheet metal parts.

Profile tolerances can be combined with other geometric controls such as flatness to control a feature.

Profile of a line tolerances apply to an entire surface.7.

Profile of a line controls apply to individual line elements.8.

Profile tolerances only control the location of a surface.9.

Composite profile controls should be avoided becausethey are more restrictive and very difficult to check.

10.

Profile tolerances can be applied either bilateral orunilateral to a feature.

11.

Profile tolerances can be applied in both freestate andrestrained datum conditions.

12.

Tolerances shown in the lower segment of a compositeprofile feature control frame control the location of afeature to the specified datums.

13.

In composite profile applications, the tolerance shown in the upper

segment of the feature control frame applies only to the ________ of the feature.

Profile Control Quiz

The two types of profile tolerances are _________________,

and ____________________. 1.

2.

3.

4.

5.

Profile tolerances can be used to control the ________, ____,

___________ , and sometimes size of a feature.

Profile tolerances can be applied _________ or __________.

_________________ tolerances are 2-dimensional controls.

____________________ tolerances are 3-dimensional controls.


6. _________________ can be used when different tolerances are required for location and form and/or orientation.

7. When using profile tolerances to control the location and/or orientation of

a feature, a _______________ must be included in the feature control frame.

8. When using profile tolerances to control form only, a ______ __________ is not required in the feature control frame.

9.

profile of a linedatum reference

composite profile bilateral

location form

primary datum

true geometric counterpart

orientationprofile of a surfaceunilateral

virtual condition

True Position Quiz


Positional tolerances are applied to individual or patternsof features of size.

1.

Cylindrical tolerance zones more closely represent thefunctional requirements of a pattern of clearance holes.

True position tolerances can control a feature’s size.

Positional tolerances are applied on an MMC, LMC, orRFS basis.

2.

3.

4.

5.

True position tolerance values are used to calculate the minimum size of a feature required for assembly.

6. Composite true position tolerances should be avoidedbecause it is overly restrictive and difficult to check.

Composite true position tolerances can only be appliedto patterns of related features.

7.

The tolerance value shown in the upper segment of acomposite true position feature control frame appliesto the location of a pattern of features to the specifieddatums.

8.

Positional tolerances can be used to control circularity

9.

10.

11.

The tolerance value shown in the lower segment of acomposite true position feature control frame appliesto the location of a pattern of features to the specifieddatums.

True position tolerances can be used to control centerdistance relationships between features of size.

Positional tolerance zones can be ___________, ___________,or spherical

1.

2.

3.

4.

5.

________________ are used to establish the true (theoretically exact) position of a feature from specified datums.

Positional tolerancing is a _____________ control.

Positional tolerance can apply to the ____ or ________________ of a feature.

_____ and ________ fastener equations are used to determineappropriate clearance hole sizes for mating details

6.

7.

_________ tolerance zones are recommended to prevent fastener interference in mating details.

8.

projected3-dimensional

surface boundary floating

location fixedbasic dimensions

maximum material

cylindricalpattern-locating rectangularfeature-relating

True Position Quiz


The tolerance shown in the upper segment of a composite true

position feature control frame is called the ________________ tolerance zone.

The tolerance shown in the lower segment of a composite true

position feature control frame is called the ________________ tolerance zone.

9. Functional gaging principles can be applied when __________________ condition is specified

axis

Runout Control Quiz


Total runout is a 2-dimensional control.1.

Runout tolerances are used on rotating parts.

Total runout tolerances should be applied at MMC.

Runout tolerances can be applied to surfaces at rightangles to the datum reference.

2.

3.

4.

5.

Circular runout tolerances apply to single elements .

6. Circular runout tolerances are used to control an entirefeature surface.

Runout tolerances always require a datum reference.7.

Circular runout and total runout both control axis to surface relationships.

8.

Circular runout can be applied to control taper of a part.9.

Total runout tolerances are an appropriate way to limit “wobble” of a rotating surface.

10.

Runout tolerances are used to control a feature’s size.11.

Total runout can control circularity, straightness, taper,coaxiality, angularity and any other surface variation.

12.

geometric dimensioning & tolerancing.ppt

Documents