gold violin quality guidelines table of...

GOLD VIOLIN QUALITY GUIDELINES

TABLE OF CONTENTS I. INTRODUCTION....................................................................................................................... 3 II. VENDOR REQUIREMENTS ................................................................................................. 3 III. GENERAL QUALITY GUIDELINES ................................................................................... 4

COMPLIANCE........................................................................................................................... 4 PERFORMANCE....................................................................................................................... 5 CONSTRUCTION AND ASSEMBLY...................................................................................... 5 APPEARANCE .......................................................................................................................... 6 LABELING................................................................................................................................. 6 PACKAGING............................................................................................................................. 7

IV. SPECIFIC PERFORMANCE STANDARDS......................................................................... 9 HOME......................................................................................................................................... 9

Appliances............................................................................................................................... 9 Clocks ................................................................................................................................... 10 Curtain And Drapery Accessories ........................................................................................ 12 Curtains, Draperies & Slipcovers ......................................................................................... 13 Cushions And Pillows........................................................................................................... 15 Decorative Accessories......................................................................................................... 17 Electronics............................................................................................................................. 19 Fans ....................................................................................................................................... 20 Furniture (Indoor And Outdoor) ........................................................................................... 22 Inflatable Mattresses ............................................................................................................. 25 Lighting – Electric & Solar................................................................................................... 27 Mattress /Cushions................................................................................................................ 28 Picture Frames, Mirrors And Albums................................................................................... 29 Repair And Tools.................................................................................................................. 31 Rugs, Door Mats And Bath Mats.......................................................................................... 32 Safety And Security .............................................................................................................. 34

BED & BATH........................................................................................................................... 35 Footwear ............................................................................................................................... 35 Socks ..................................................................................................................................... 37

TRAVEL................................................................................................................................... 39 Totes, Purses, Luggage, and Cosmetic Cases ....................................................................... 39

KITCHEN AND DINING ........................................................................................................ 43 Candles.................................................................................................................................. 43 Candle Holders and Candelabras .......................................................................................... 45 Cookware, Tools & Utensils................................................................................................. 47 Food Containers .................................................................................................................... 49 Tablecloths, Napkins, Place Mats & Table Runners ............................................................ 51 Towels................................................................................................................................... 53

GIFTS AND GADGETS .......................................................................................................... 55 Games And Toys................................................................................................................... 55

GIFTS AND GADGETS .......................................................................................................... 57 PET PRODUCTS...................................................................................................................... 58

Norm Thompson Outfitters, Inc. 9/4/2007 1


Safety Guidelines .................................................................................................................. 58 YARD AND GARDEN............................................................................................................ 59

Apparel – Outdoor ................................................................................................................ 59 Cleaners And Chemicals....................................................................................................... 61 Flexible Accessories ............................................................................................................. 62 Hard....................................................................................................................................... 63



I. INTRODUCTION Welcome to the Gold Violin Quality Guideline manual. The following guidelines are intended to familiarize you with our quality requirements. II. VENDOR REQUIREMENTS

1. Vendors are requested, on the purchase order, to send Top of Production Samples to Product Quality Management at Gold Violin Corporate Offices in Oregon before shipping any order to the Distribution Center.

2. These Top of Production Samples are not to be confused with Photo Samples sent earlier

to Gold Violin Merchants.

3. Top of Production Samples must be received by Product Quality Management (PQM) by the date requested on the Purchase Order. If this deadline is not met, a $300 chargeback is applicable.

4. To be approved for shipment, Top of Production Samples must meet standards which

include, but are not limited to, the following General Guidelines and Specific Guidelines for each product category.

5. Vendors are responsible for physical testing that meets Gold Violin requirements. The

majority of performance criteria for Hardgoods products is based on actual use in typical consumer conditions. This is supplemented whenever possible by standard industry test methods. Test standards used for Hardgoods include those written by ISO, FTC, FCC, ANSI, AATCC, ASTM, and SATRA.

INTRODUCTION Gold Violin Quality Guidelines are presented in two sections. The first section contains general characteristics that can be applied to all/most Hardgoods products. The second section contains guidelines that are specific to individual categories of products. Vendors are expected to be familiar with and produce products for Gold Violin based on the Guidelines found in both the general and the specific sections. It is possible that a particular undesirable criteria in the Guidelines could be desirable on certain products for design and/or aesthetic reasons. To avoid confusion, variations will be clearly indicated on the product spec sheet produced by Vendor or Merchandiser or be authorized in writing by the Merchandiser and/or Product Quality Technician.



III. GENERAL QUALITY GUIDELINES COMPLIANCE

1. Product shall meet all agreed-upon product specifications.

2. Measurements (height, width, weight, if applicable) shall conform to specifications

and/or match approved samples. Variances on some Softgoods items must fall within previously agreed upon tolerance ranges.

3. Colors shall conform to agreed-upon standards or approved samples.

4. Country of origin indicated on item must conform to order sheet or specs.

5. Materials and/or composition must comply to order sheet or specs.

6. Components must be included and packed and secured as specified.

7. Assembly, use and care instructions must be included if applicable.

8. Item style number must conform to order sheet or agreed-upon specs.

9. Substitutions or product changes, product design, material changes, factory changes, etc.,

may not take place without approval from Merchandiser and Product Quality Management Technician.

10. Vendor must be prepared to provide documentation showing that product has passed lab-

and field-tests if required by Merchandiser or Product Quality Technician.

11. Vendor must be prepared to provide documentation that product meets all applicable Federal and Safety Regulations such as FDA, FHSA, CPSC, US CUSTOMS, FTC, etc.

12. Vendor must provide a completed Material Safety Data Sheet (MSDS) for any chemical

that poses a physical or health hazard in the workplace. MSDS lists the following:

a. Identity of the chemical b. Physical and chemical characteristics (i.e. vapor pressure, flash point) c. Physical hazards d. Health hazards e. Primary routes of entry f. Exposure limit recommended g. Whether it is a carcinogen h. Precautions for safe handling and use i. Control measures j. Emergency and first-aid procedures



k. Date of preparation and last revision of MSDS l. Name, address, telephone number of manufacturer, importer or other responsible

party.

13. Containers of hazardous chemicals must be labeled. The information on the label must include the identity of the chemical, appropriate hazard warnings, and the name and address of the manufacturer, importer, or other responsible party.

PERFORMANCE

1. All product parts must be in working order.

2. Performance, durability and reliability of product must meet Manufacturer’s/Vendor’s description and claims.

3. Product must pass applicable lab and field tests reinforcing performance claims.

CONSTRUCTION AND ASSEMBLY

1. Product must be absent of flaws including but not limited to: a) Holes, rips, tears in fabrics b) Chips, cracks, dents, scratches c) Defective stitching d) Unsecured hardware

2. Improper welding 3. Rough edges, sharp points

4. All components must be assembled well.

5. Mechanics must operate smoothly.

6. All components must be well secured and function as intended.

7. Product must be free of splinters, burrs, insect invasion, and fungus.



APPEARANCE

1. Product must be absent of aesthetic flaws including, but not limited to:

2. Soilage a. Paint chipping b. Scratches to the finish c. Oil spots d. Rust spots e. Chalk marks or similar markings f. Glue marks g. Paint, stain or finish which is not smooth, or which drips or runs

3. Product must be absent of any objectionable odors.

4. Product must be free of mold and fungus.

LABELING

1. Product must be properly labeled with SKU#, product #, and other information specified on Purchase Order.

2. Labels must not be soiled, crooked, or defaced in any way

3. No handwritten information is to appear on labels.

4. Product must include all information required by USA federal and state laws.

5. Country of origin must be affixed to each individual unit.

6. Sticky label on gift items must not deface product when removed.

7. Required labeling should not interfere with gift presentation.

8. Products requiring instructions or directions must include them in clear and correct

English.

9. No pricing labels, stickers, or tags to appear on product.



PACKAGING

1. Product must be packaged in accordance with instructions in the Vendor’s Manual.

2. Product must be packaged sufficiently to prevent damage during shipping.

3. Guidelines for polybagging must be followed:

a. Items that must be polybagged: • Hazardous/ORM-D liquids. This is to help eliminate any spillage. • Items that are twin packed and not already shrink wrapped, blister packed or

polybagged together. • Bottles with attachments or accessories. This will help keep the attachment

with the bottle. • Safety caution must appear prominently on all polybags. • Any liquid that is not hermetically sealed. A hermetically sealed item usually

has a foil seal that is affixed to the lid by vacuum and glue. • Packaging on individual products should be free of stains, oil spots and dirt. • No torn or crushed boxes are allowed.

b. Items that do not need to be polybagged:

• Items that are in a paste consistency and not likely to leak. • Any non-hazardous ORM-D item that is hermetically sealed. • Any item that is of a gel or lotion consistency, which is sealed and is not

likely to leak. • Any product that is blister packed.

4. Package (individual polybag, box, etc.) must have proper labels as specified on Purchase

Order Form and must be placed on product as specified in Vendor’s Manual.

5. No pricing is to appear on package or product.

6. No unapproved inserts, catalog advertisements, customer solicitation, customer survey, supplier’s phone number or E-mail address is to appear on package or product.

7. Any changes in packaging from agreed-upon specs must be approved by Merchandiser

and/or Product Quality Technician.



INTRODUCTION The following is a list of Hardgoods and Softgoods tests arranged in categories.

• All criteria listed previously in GENERAL QUALITY GUIDELINES are to be

practiced.

• In addition, all products must meet or exceed the following applicable SPECIFIC PERFORMANCE STANDARDS.

Gold Violin Merchants or Product Quality Technicians may require testing verification before approval of product can be given.



IV. SPECIFIC PERFORMANCE STANDARDS

HOME Appliances

(Including, but not limited to, ice shavers, thermometers, portable refrigerators,

ice cream makers, mini-ovens, electric kettles, hair dryers, etc.)

EVALUATION REQUIREMENT TEST METHOD Labeling Country of Origin Verify actual FTC Manufacturer’s Identity (RN#) Verify actual FTC UL/ETL/CSA Listing Verify actual Lead Content Less than 0.06% by dry weight 16 CFR 1303 Workmanship No cracks or other visible defects, Visual Evaluation even coatings without scratches or blisters. No rough edges or sharp points. Resistance to Tipping No instability @ 10° Hold at 10° angle and (Tabletop items only) release. Functional Use No visible damage; Operate for adjustable parts operate smoothly 48 hours with four and remain securely in adjustments to any position moveable part checking at least 6 times Cord Strength No detachment from appliance Pull on cord using 30 lbs. for 1 min. Drop Resistance Should function properly 2 drops to vinyl surface after dropping from 36". Resistance to Humidity No significant change Exposure to 95% RH for 24 hours at room temperature Resistance to Extreme No significant change Exposure to 32°F and Temperature 120°F for 24 hours each Power Switch Durability Remain functional Manual operation of on- off switch for 1,000 cycles



HOME Clocks

(Including, but not limited to, electric and battery operated clocks)

EVALUATION REQUIREMENT TEST METHOD

Labels Country of Origin Must be on face and housing FTC Manufacturer’s Identity (RN#) Verify actual FTC Battery Markings Number of batteries required, FCC size and polarity of batteries Battery Use Instructions regarding the safe FCC disposal of batteries Serial number (if >$50 price) Verify actual CA Appliance Code 22410 Materials Verify actual Visual examination Lead Content (Surface coatings only) <0.06% by weight 16 CFR 1303 Workmanship No cracks or other visible defects, Visual evaluation while even coatings without scratches feeling product or blisters. No sharp points or rough edges. No rocking when placed on flat surface. Glass edges sanded and smooth. Resistance to Tipping No instability @ 10° Hold at 10° angle and

release. Functional Use Shall perform as intended Operate for 48 hours checking all functions at least 4 times Accuracy ±1 second per day or as agreed Standard measurement between buyer and seller Water Resistance (If applicable) Shall conform to product claim ISO 2281 Alarm Function Shall conform to product claim Complete 4 full use cycles Alarm Sound Report noise level Measure by sound meter 12" from source of sound



Clocks, continued


Shock Resistance No damage ISO 1413 Drop Test Should function properly with 2 drops to vinyl surface consistent accuracy from 36". Accuracy checked before and after both drops Resistance to Humidity No significant change Exposure to 95% RH for 24 hours at room temperature Resistance to Extreme No significant change Exposure to 32°F and Temperature 120°F for 24 hours each



HOME Curtain And Drapery Accessories

(Including, but not limited to, rods, brackets and shelves)


Labeling Country of Origin Verify actual FTC Manufacturer’s Identity (RN#) Verify actual FTC Lead Content (Surface coatings only) <0.06% by weight 16 CFR 1303 Workmanship No cracks or other visible defects, Visual Evaluation even coatings without scratches or blisters Corrosion Resistance No significant change Soak for 24 hours in (Metal products only) 1% saline solution

Resistance to Extreme No significant change 24 hours @32° F and Temperature 24 hours @ 120° F Resistance to Humidity No significant change 24 hours @95% RH Moisture Content 8-12% max. Moisture Meter (Large wood products only) Load Capacity Rods & brackets No deformation or structural Apply 20 lb. load to

changes mounted item for 48 hours

Shelves No deformation or structural Apply 50 lb. load to changes mounted item for 48

hours



HOME Curtains, Draperies & Slipcovers

(Including, but not limited to, insulated and non-insulated, lined and unlined draperies,

curtains, valances and slipcovers)


Labeling Country of Origin Verify actual FTC Manufacturer’s Identity (RN#) Verify actual FTC Fiber Content Verify actual FTC Care Instructions Verify actual FTC Fiber Content Single Fiber No Tolerance AATCC 20 Multiple fibers 3% Tolerance Yarn Size Report Actual ASTM D1059 Thread Count Report Actual ASTM D3775/3887 Weight Report Actual ASTM D3775/3887 Dimensional Change (3HL) Length 0 to -5% AATCC 135 Width 0 to -5% Dimensional Change (1DC) Length 0 to -4% AATCC 158 Width 0 to -4% General Appearance after No significant change Visual evaluation Laundering including surface, color, shape, etc. Effects of Cleaning Solution (Slipcovers) Surface Appearance Grade 4 AATCC 124 Shade Change Grade 4 AATCC 61 or 132 Colorfastness to Laundering (Washable products only) AATCC 61 Shade change Grade 4 min. Staining Grade 3 min. Self-staining Grade 4 min. Colorfastness to Bleach (Washable products only) Chlorine Grade 4 min. Spot Test Non-chlorine Grade 4 min. Soak Test



Curtains, Draperies and Slipcovers, continued


Colorfastness to Light (60 AFUs) AATCC 16E Synthetics Grade 4 min. Natural fibers Grade 3 min. Colorfastness to Water (Washable products only) AATCC 107 Shade change Grade 4 min. Staining Grade 4 min. Self-staining Grade 4 min. Tensile Strength ASTM D5034

Sheers 15 lbs. min. Others 30 lbs. min. Slipcovers 50 lbs. min. Tear Strength (Slipcovers only) ASTM D1424 Slipcovers 4.0 lbs. min. Seam Slippage Sheers 15 lbs. at ¼" ASTM D434 Others 20 lbs. at ¼" Flammability Pass ASTM D4151



HOME Cushions And Pillows

(Including, but not limited to, decorative pillows & cushions, functional pillows, pet cushions/pads and draft stoppers)


Labeling Country of Origin Verify actual FTC Manufacturer’s Identity (RN#) Verify actual FTC Fiber Content Verify actual FTC Care Instructions Verify actual FTC CA Law Label Verify actual CA Bureau Home Furnishings Fiber Content Single Fiber No Tolerance AATCC 20 Multiple fibers 3% Tolerance Yarn Size Report Actual ASTM D1059 Thread Count (Cover fabric only) Report Actual ASTM D3775/3887 Feather count (Pillow inserts only) Report Actual Visual evaluation Fill Weight (Pillow inserts only) Report Actual Standard Measure Weight, oz./sq. yd (Cover fabric only) Report Actual ASTM D3775/3887 Dimensional Change (3HL) Length 0 to -5% AATCC 135 (Washable products only) Width 0 to -5% Dimensional Change (1DC) Length 0 to -4% AATCC 158 (Dry cleanable products only) Width 0 to -4% General Appearance after No significant change Visual evaluation Laundering (3HL or 1DC) including surface, color, shape, etc. Colorfastness to Laundering (Washable products only) AATCC 61 Shade change Grade 4 min. Staining Grade 3 min. Self-staining Grade 4 min.



Cushions and Pillows, continued

EVALUATION REQUIREMENT TEST METHOD Colorfastness to Bleach (Washable products only) Chlorine Grade 4 min. Spot Test Non-chlorine Grade 4 min. Soak Test Colorfastness to Light (40 AFU’s) AATCC 16E Synthetics Grade 4 min. Natural fibers Grade 3 min. Colorfastness to Water (Washable products only) AATCC 107 Shade change Grade 4 min. Staining Grade 4 min. Self-staining Grade 4 min. Tensile Strength 30 lbs. min. ASTM D5034 Tear Strength 3 lbs. min. ASTM D1424 Seam Slippage 20 lbs. at ¼" ASTM D434 Seam Strength 20 lb./in. ASTM D1683 Pile Retention (Napped fabrics only) Back Grade 4 ASTM D4685 Face Grade 3 Surface Abrasion Grade 3 at 9,000 cycles ASTM D4157 (Only Pet Beds & Pet Cushions) Flammability (pillows >26" only) Pass CA Tech Bulletin 117



HOME Decorative Accessories

(Including, but not limited to, rainbow makers, flower pots, vases, coasters, wine charms, fishbowls, signs, non-electric holiday decorations and ring holders)

EVALUATION REQUIREMENT TEST METHOD Labeling Country of Origin Verify actual FTC Manufacturer’s Identity (RN#) Verify actual FTC Lead Content (Surface coatings only) <0.06% by weight 16 CFR 1303 Workmanship No cracks or other visible defects, Visual evaluation while even coatings without scratches feeling product or blisters. No sharp points or rough edges. No rocking when placed on flat surface. Drop test (non-fragile items) No breakage or separation ASTM F963 One drop from 12" Effects of Extreme No significant change 24 hours @ 32° F and Temperature 24 hours @ 120° F Effects of Humidity No significant change 24 hours @95% RH and 100° F Moisture Content 8-12% max. Moisture Meter (large wood products only) Seepage resistance No seepage from items designed to Fill container to hold water capacity with room temperature water. Let sit for 24 hours. Tilt Test (Freestanding items only) No damage after fall Tilt at angle until

product falls.

Resistance to Tipping No instability @ 10° Hold at 10° angle and release.



Decorative Accessories, continued

EVALUATION REQUIREMENT TEST METHOD Functional Use Shall perform as intended Use for 48 hours checking at 2 hour intervals Corrosion Resistance No significant change Soak for 24 hours in (Metal products only) 1% saline solution Impact Resistance No breakage or separation Attach 3 oz. steel ball to (Glass and ceramic items only) string. Hold 3 in. away from product. Release ball to impact product. Cycle 4 times. Surface scratching tendency No scratching of other surfaces 5 cycles, 10" back & (Tabletop products only) forth on wood, glass and plastic laminate Cross-cut Adhesion (Plated items only) Coating must stay ASTM D3359B fixed to base Dishwasher Safe No cracking, crazing, chipping or 10 cycles normal wash (If applicable) color change with detergent Flammability Pass 16 CFR 1500.3



HOME Electronics

(Including, but not limited to, bug zappers, pet trainers and rodent repellers)

EVALUATION REQUIREMENT TEST METHOD Labeling Country of Origin Verify actual FTC Manufacturer’s Identity (RN#) Verify actual FTC Lead Content (Surface coatings only) <0.06% by weight 16 CFR 1303 Workmanship No cracks or other visible defects, Visual evaluation while even coatings without scratches feeling product or blisters. No sharp points or rough edges. Resistance to Extreme No significant change 24 hours @ 32° F and Temperature 24 hours @ 120° F Resistance to Humidity No significant change 24 hours @ 95% RH Water Resistance (If applicable) Conforms to product claims ISO 2281 Shock Resistance No damage ISO 1413 Impact Resistance No visible damage 2 drops onto vinyl surface from 36" height (random orientation) Functional Use Functions as intended Actual use for 48 hours checking at 2 hour intervals



HOME Fans

(Including, but not limited to, electric fans and battery- operated fans)


Labels Country of Origin Verify actual FTC Manufacturer’s Identity Verify actual FTC Battery Markings Number of batteries required, FCC size and polarity of batteries Battery Use Instructions regarding the safe FCC disposal of batteries Serial number (if >$50 price) Verify actual CA Appliance Code 22410 UL, ETL or CSA Verify actual Visual Examination Battery Labeling (If applicable) Shall have legible battery polarity, Visual Examination size, voltage in compartment Lead Content (Surface coatings only) <0.06% by weight 16 CFR 1303 Workmanship No cracks or other visible defects, Visual evaluation while even coatings without scratches feeling product or blisters. No sharp points or rough edges. No rocking when placed on flat surface. Tilt Test (Free standing fans only) No damage after fall Tilt at angle 3 times

on hard surface until fan falls

Resistance to Tipping No instability @ 10° Hold at 10° angle and release.

Functional Use Shall perform as intended Use for 48 hours. Perform visual examination 4 times during use and after use. Cord Strength No detachment from fixture Pull cord using 40 lb. force for 1 minute



Fans, continued


Power Switch Durability Remain functional Manual operation of on-off switch for 1,000 cycles Impact Resistance No visible damage 2 drops onto vinyl (Portable fans only) surface from 36" height (random orientation) Resistance to Humidity No significant change Exposure to 95% RH for 24 hours at room temperature Resistance to Extreme No significant change Exposure to 32°F and Temperature 120°F for 24 hours each



HOME Furniture (Indoor And Outdoor)

(Including, but not limited to, chairs, footstools, benches, tables, stands, shelves, cabinets and trunks)

EVALUATION REQUIREMENT TEST METHOD Labeling Country of Origin Verify actual FTC Manufacturer’s Identity (RN#) Verify actual FTC Fiber Content Verify actual FTC Care Instructions Verify actual FTC CA Flammability Verify actual CA Bureau Home Furnishings Workmanship No cracks or other visible defects, Visual evaluation while even coatings without scratches feeling product or blisters. No sharp points or rough edges. Back Pull Strength Pass – No damage 100 lb. For 1 minute (Chairs & benches with backs only) applied to 90° from back at 16" above seat Arm Pull Strength Pass – No damage ASTM F1858, apply

250 lbs./ in. at speed <6" per sec., hold for 1 minute

Base Durability Pass – No damage 400 lbs. per each sitting (Chairs & benches only) area, apply for 10 sec. at a rate not exceeding

6" per sec., repeat for another 8 cycles, then allow the mass on the seat to sit for an additional 30 min..

Impact Durability Pass – No damage 150 lbs. weight (Chairs & benches only) dropped 10 times on different areas of seat from height of 6"


GOLD VIOLIN QUALITY GUIDELINES Furniture (Indoor and Outdoor), continued

EVALUATION REQUIREMENT TEST METHOD Load Capacity Shelves No deformation or 40 lb. load applied for shape change 24 hours Tables No deformation or 80 lb. load applied for shape change 24 hours Chairs No deformation or 150 lb. load applied shape change for 24 hours Moisture Content (Wood products only) 8% - 12% Moisture Meter Resistance to Corrosion No visible rust ASTM B117 / 24 hours (Coated tubes or metal parts only) Flammability Pass CA Tech Bulletin 116/117 Lead Content (Surface coatings only) <0.06% by weight 16 CFR 1303

The following pertains only to furniture containing upholstery fabric Labeling CA Plumage Verify actual CA Bureau of Home (Products containing plumage) Furnishings CA Flammability Verify actual CA Bureau of Home (Upholstered furniture & cushions) Furnishings CA Law Label Verify actual CA Bureau of Home (Filled or padded products) Furnishings Count Report actual ASTM D3775 Weight Report actual ASTM D3776 Tensile Strength 40 lbs. min. ASTM D5034 Tear Strength 6 lbs. min. ASTM D1424 Seam Strength 30 lbs. min. ASTM D1683 Surface Abrasion Grade 3 at 9,000 cycles ASTM D4157 Crocking AATCC 8 or 116 Dry Grade 4 Wet Grade 3



Furniture (Indoor and Outdoor), continued

EVALUATION REQUIREMENT TEST METHOD Lightfastness – 40 AFUs Grade 4 AATCC 16E Effects of Cleaning Solution Surface Appearance Grade 4 AATCC 124 Shade Change Grade 4 AATCC 61 or 132



HOME Inflatable Mattresses

(Including, but not limited to, manual or pump- filled air mattresses, cushions and pillows)

EVALUATION REQUIREMENT TEST METHOD Labels Country of Origin Verify actual FTC Manufacturer’s Identity Verify actual FTC Lead Content (Surface coatings only) <0.06% by weight 16 CFR 1303 Size Verify size Standard measure Workmanship No punctures or other visible defects, Visual evaluation while even coatings without scratches feeling product or blisters. No sharp points or rough edges. Functional Use Shall perform as intended, Operate for 48 no leaks in mattress hours with 200 lb. load. Checking at least 4 times Power Switch Durability Remain functional Manual operation of on-off switch for 1,000 cycles Valve Strength 15 lbs. without detachment 16 CFR 1500, 15 lbs. for 10 sec. Resistance to Humidity No significant change Exposure to 95% RH for 24 hours at room temperature Resistance to Extreme No significant change Exposure to 32°F and Temperature 120°F for 24 hours each Puncture Resistance 3 lbs. minimum ASTM F1342 Report thickness of

material and force to puncture to nearest

0.01 lbs. (50g)



Inflatable Mattresses, continued

EVALUATION REQUIREMENT TEST METHOD Load Strength Pass – no damage 400 lbs. evenly distributed for 4 hours Bursting Strength No damage Inflate to 1.1 times recommended pressure



HOME Lighting – Electric & Solar

(Including, but not limited to, lamps, lanterns, address markers and light bulbs)

EVALUATION REQUIREMENT TEST METHOD Labeling Country of Origin Verify actual FTC Manufacturer’s Identity (RN#) Verify actual FTC UL/ETL/CSA Listing Verify actual UL 153 Bulb type & maximum wattage Verify actual UL 153 Lead Content (Painted surfaces only) Less than 0.06% by dry weight 16 CFR 1303 Workmanship No cracks or other visible defects, Visual Evaluation even coatings without scratches or blisters. No rough edges or sharp points. Functional Use No visible damage, Operate for adjustable parts operate smoothly 48 hours with four and remain securely in new adjustments to any position moveable part - checking at 4 hour intervals Cord Strength No detachment from fixture Pull on cord using 40 (Non-solar powered lights only) lbs. for 1 minute Tilt Resistance (Free standing lights only) No damage after fall Tilt at angle until product falls

Resistance to Tipping No instability @ 10° Hold at 10° angle and (Tabletop lights only) release Effects of Humidity No significant surface change 24 hours, 95% RH, 100°F Effects of Temperature No significant surface change 32°F for 24 hours and (Outdoor lights only) 120°F for 24 hours Surface scratching No scratching of other surfaces 5 cycles, 10" back & (Tabletop lights only) forth on wood, glass and plastic laminate Cross-cut Adhesion (Mirrored parts only) Silver coating must stay ASTM D3359B fixed to glass



HOME Mattress /Cushions

(Including, but not limited to, lined and unlined washable mattress pads and cushions)

EVALUATION REQUIREMENT TEST METHOD Labeling Country of Origin Verify actual FTC Manufacturer’s Identity (RN#) Verify actual FTC Fiber Content Verify actual FTC Care Instructions Verify actual FTC CA Law Verify actual CA Bureau Home Furnishings Fire Retardant Verify actual 16 CFR 1632 If fire retardant treatment used, a letter “T” must appear on a permanent label Fiber Content Single Fiber No Tolerance AATCC 20 Multiple fibers 3% Tolerance Dimensional Stability (3HL) 5% max warp and fill AATCC 150 Dimensional Stability (1DC) 4% max warp and fill AATCC 158 Seam Strength 20 lb./in. ASTM D1683 Seam Slippage 20 lb @ 1/4" ASTM D434 Tensile Strength 25 lb./in. ASTM D5034 Tear Strength 2 lb./in. ASTM D1424 Flammability Pass 16 CFR 1632



HOME Picture Frames, Mirrors And Albums

(Including, but not limited to, stand-up frames, hanging frames, framed mirrors, photo albums, photo display boxes, photo coasters, wall mirrors, vanity mirrors and purse mirrors)


Labels Report Actual FTC Country of Origin Manufacturer’s Identity (RN #) Materials Verify actual Visual examination Lead Content (Surface coatings only) <0.06% by weight 16 CFR 1303 Mechanical Hazards No sharp edges or points 16 CFR 1500 (For children’s products) Workmanship No cracks or other visible defects, Visual evaluation while even coatings without scratches feeling product or blisters. No rocking when placed on flat surface. Glass edges sanded and smooth. Resistance to Tipping No instability @ 10° Hold at 10° angle & (Stand-up products only) release Resistant to Dropping (Not applicable to glass and mirrors) No visible damage 4 drops to vinyl floor from 36" Resistance to Impact No visible damage Tip product over on wooden surface 3 times Cross-cut Adhesion (Mirrors only) Silver coating must stay fixed to glass ASTM D3359B Number of Pockets (Albums only) Report Actual Visual Examination Binding Strength (Albums only) No visible tear or damage Fill pockets with load twice the total product weight and suspend front cover pages freely for 1 hour



Picture Frames, Mirrors and Albums, continued


Cold Crack (Albums only) No breakage in more than Modified ASTM D1539 1 specimens (0°F / 1 hr.) and impact by the fixture on 10 specimens randomly drawn from the pockets Colorfastness to Crocking Dry Grade 4 AATCC 8 or 116 (Album fabric only) Wet Grade 3 Hinge Strength (Frames only) No detachment from frame Tension of 5 lbs. Resistance to Humidity No significant change Exposure to 95% RH for 24 hours at room temperature Resistance to Extreme No significant change Exposure to 32°F and Temperature (Albums excluded) 120°F for 24 hours each



HOME Repair And Tools

(Including, but not limited to, toolboxes, toolbox contents and life hammers)

EVALUATION REQUIREMENT TEST METHOD Labeling Country of Origin Verify actual FTC Manufacturer’s Identity (RN#) Verify actual FTC Lead Content Less than 0.06% by dry weight 16 CFR 1303 Workmanship No cracks or other visible defects, Visual evaluation while even coatings without scratches feeling product or blisters Functional Use Functions as intended 10 full use cycles Effects of Extreme No significant change 24 hours @ 32° F and Temperature 24 hours @ 120° F Effects of Humidity No significant change 24 hours @ 95% RH and 100° F Corrosion Resistance No significant change Soak for 24 hours in

1% saline solution

Drop Impact No significant damage Drop 3 times from 36" to a concrete surface



HOME Rugs, Door Mats And Bath Mats

(Including, but not limited to, textile fiber rugs, plastic mats, indoor and outdoor mats, etc.

Does not apply to wool or animal- fiber rugs)

EVALUATION REQUIREMENT TEST METHOD Labeling Country of Origin Verify actual FTC Manufacturer’s Identity (RN#) Verify actual FTC Fiber Content Verify actual FTC Care Instructions Verify actual FTC Fiber Content Single Fiber No Tolerance AATCC 20 Multiple fibers 3% Tolerance Flammability Rugs <24 sq. ft. Pass 16 CFR 1631 Rugs >24 sq. ft. Pass 16 CFR 1630 Dimensional Change 3HL Length ±5% AATCC 135 (Washable products only) Width ±5% General Appearance after No significant change Visual evaluation Laundering (Washable products only) Including surface, color, shape, etc. Colorfastness to Laundering (Washable products only) AATCC 61 Shade change Grade 4 min. Staining Grade 3 min. Self-staining Grade 4 min. Colorfastness to Bleach (Washable products only) Chlorine Grade 4 min. Spot Test Non-chlorine Grade 4 min. Soak Test Colorfastness to Light AATCC 16E 40 AFU exposure Grade 4 min. Colorfastness to Water (Washable products only) AATCC 107 Shade change Grade 4 min. Staining Grade 4 min. Self-staining Grade 4 min.



Rugs, Door Mats and Bath Mats, continued

EVALUATION REQUIREMENT TEST METHOD Tensile Strength 50 lbs. min. ASTM D5034 Skid Resistance Coefficient of ASTM F609 (Plastic mats and coated rugs) friction 0.4 min. Rug Back Staining Grade 4 AATCC 137 (Plastic mats and coated rugs)



HOME Safety And Security

(Including, but not limited to, outlet covers and intercoms)

EVALUATION REQUIREMENT TEST METHOD Labeling Country of Origin Verify actual FTC Manufacturer’s Identity (RN#) Verify actual FTC UL/ETL/CSA Listing Verify actual Lead Content Less than 0.06% by dry weight 16 CFR 1303 Workmanship No cracks or other visible defects, Visual evaluation while even coatings without scratches feeling product or blisters. No rough edges or sharp points. Functional Use No visible damage, Operate for adjustable parts operate smoothly 48 hours with four and remain securely in new adjustments to any position. moveable part - Checking at 4 hour intervals Effects of Extreme No significant change 24 hours @ 32° F and Temperature 24 hours @ 120° F Effects of Humidity No significant change 24 hours @ 95% RH and 100° F Surface Scratching No scratching of other surfaces 5 cycles, 10" back & (If applicable) forth on wood, glass and plastic laminate



BED & BATH Footwear

(Including, but not limited to, slippers, slip-ons and sandals)

EVALUATION REQUIREMENT TEST METHOD Labeling Country of Origin Verify actual FTC Manufacturer’s Identity (RN#) Verify actual FTC Sole Durability 2,000 cycles with ASTM D3886 0.75 gm. loss max Coefficient of Friction Original 0.40 min. ASTM F609 Scuffed 0.50 min. ASTM F609 Ross Shoe Flex 0.1 inch @ 50,000 cycles SATRA Cold Flex No cracking @ -20°F ASTM D1790 Heavy Metals (Leather only) 100 ppm (mg/kg) Acid digestion &

Lead ICP/UV-VIS Cadmium Mercury Chromium VI Free Formaldehyde 150 ppm (mg/kg) DIN 53315 (Leather, PVC/PU and fabrics) Azo Dyestuff 30 ppm (mg/kg) LMBG §35 (Leather, PVC/PU and fabrics) B82.02-4 Disperse Dyes None allowed DIN NMP 512 WD (Leather and fabrics)



Footwear, continued

EVALUATION REQUIREMENT TEST METHOD Colorfastness to Light AATCC 16E 20 AFU exposure Interior Grade 3.5 min. Exterior Grade 4 min. Colorfastness to Water AATCC 107 Interior Shade change Grade 4 min. Staining Grade 3 min. Self-staining Grade 3.5 min. Exterior Shade change Grade 4 min. Staining Grade 4 min. Self-staining Grade 4 min. Colorfastness to Perspiration AATCC 15 Interior Shade change Grade 4 min. Staining Grade 4 min. Self-staining Grade 3.5 min. Exterior Shade change Grade 4 min. Staining Grade 4 min. Self-staining Grade 4 min. Colorfastness to Crocking (Interior and Exterior) AATCC 8 Light & medium shades Dry Grade 4 min. Wet Grade 3.5 min. Suedes & dark shades Dry Grade 3.5 min. Wet Grade 2.5 min.



BED AND BATH Socks

(Including, but not limited to, support socks and knee-highs)

EVALUATION REQUIREMENT TEST METHOD Labeling Country of Origin Verify actual FTC Manufacturer’s Identity (RN#) Verify actual FTC Fiber Content Verify actual FTC Care Instructions Verify actual FTC Fabric Count Report actual ASTM D3887 Fabric Weight Report actual (oz./doz. pair) ASTM D3776 Fiber Content 3% Tolerance AATCC 20 0% Tolerance on 100% fabrics Fit Properties Must fit labeled size range using NAHM NAHM forms before and after 3HL AATCC 150 following care instructions Abrasion Resistance Blends – 400 cycles min. ASTM D3886 Cotton – 200 cycles min. Pilling Resistance Class 4 at 300 cycles min. ASTM D3514 Colorfastness to Laundering Shade change Grade 4 min. AATCC 61 Staining Grade 3.5 min. Self-staining Grade 4.5 min. Colorfastness to Crocking AATCC 8 or 116 Light & medium shades Dry Grade 4 min. Wet Grade 3.5 min. Dark shades & Pigments Dry Grade 3.5 min. Wet Grade 2.5 min.


GOLD VIOLIN QUALITY GUIDELINES Socks, continued

EVALUATION REQUIREMENT TEST METHOD Colorfastness to Light – 20 AFU’s - Grade 3.5 min. AATCC 16E Colorfastness to Chlorine Bleach Grade 4 min. Spot Test Colorfastness to Non-chlorine Bleach Grade 4 min. Soak Test Colorfastness to Perspiration Shade Change Grade 4 min. AATCC 15

Staining Grade 3 min. Self-staining Grade 4.5 min. Flammability Class I 16 CFR 1610 Free Formaldehyde 150 ppm (mg/kg) DIN 53315 (Leather, PVC/PU, and fabrics) Azo Dyestuff 30 ppm (mg/kg) LMBG §35 (Leather, PVC/PU, and fabrics) B82.02-4 Disperse Dyes None allowed DIN NMP 512 WD (Leather and fabrics)



TRAVEL Totes, Purses, Luggage, and Cosmetic Cases

(Including, but not limited to, totes, purses, luggage and cosmetic cases. Refer to Pillow/Cushion Performance Guideline for pet beds, pet seats and

automobile pet seat protectors.)

EVALUATION REQUIREMENT TEST METHOD Labeling Country of Origin Verify actual FTC Manufacturer’s Identity (RN#) Verify actual FTC Roller Performance No cracks, fractures, excessive Roll on concrete (If applicable) wear or objectionable noise surface for 4000 yards containing 40 lbs. load Roller Pull (If applicable) 3 lbs. max Fill with 50 lb. load, run

over 20 mm high ramp at a speed of 0.5 m/s for 25 km

Capacity Overload No damage Apply twice the claimed weight for hours

Jerk Test No damage Apply claimed weight,

jerk over 4' at speed of 5 sec. per cycle for 2000 cycles

Component (Attachment) Strength Main Handle: 60 lbs ASTM D1683

Shoulder Strap 40 lbs Carry Handle 30 lbs Reinforced stress points 25 lbs Rollers 25 lbs Side Handle 20 lbs Buckles 20 lbs Misc small parts 10 lbs Snaps 15 lbs /10secs ASTM Provisional Lock Performance Operates smoothly, quietly, 200 cycles actual use (If applicable) and operates as intended Resistance to Humidity No change 24 hours @ (Metal components only) 100° F and 95% RH



Totes, Purses and Luggage, continued

EVALUATION REQUIREMENT TEST METHOD Resistance to Corrosion No change 24 hours with 1% saline (Metal parts only) solution Drop Test No shape distortion, loose or ASTM D5276 broken parts 40 lbs. load Seam Strength Luggage: 50 lbs. min. ASTM D1683 (Wovens only) Bags: 40 lbs. min. Wallets: 25 lbs. min. Seam Slippage 25 lbs. min. ASTM D434 (Prototype seam) Zipper Strength

Crosswise Strength Luggage: 80 lbs. min. ASTM D2061 Bags: 50 lbs. min.

Wallets: 30 lbs. min. Slider Pull-off Strength Luggage: 25 lbs. min. ASTM D2061 Bags: 22 lbs. min. Wallets: 20 lbs. min. Scoop Pull-off Strength Luggage: 10 lbs. min. ASTM D2061 Bags: 8 lbs. min. Wallets: 5 lbs. min. Top Stop 20 lbs. min. ASTM D2061 Bottom Stop 20 lbs. min. ASTM D2061 Slider Torque 2 lbs. min. ASTM D2061 Operability Strength 5 lbs. min. ASTM D2061

Snap Strength ASTM D4846

Snapping 2 lbs. max Unsnapping 6 lbs. min.

Tensile Strength ASTM D5034

Fabric Luggage: 80 lbs. min. Bags: 60 lbs. min.

Wallets: 40 lbs. min. Leather 40 lbs. min. Tearing Strength ASTM D1424

Fabric Luggage: 6 lbs. min. Bags: 4 lbs. min.

Wallets: 4 lbs. min. Leather 4 lbs. min. Fiber Content 3% tolerance AATCC 20 0 tolerance on 100% fabrics



Totes, Purses, and Luggage, continued

EVALUATION REQUIREMENT TEST METHOD Fabric Weight Report actual ASTM D3776 Fabric Count Report actual

Knits ASTM D3887 Wovens ASTM D3775

Colorfastness to Water AATCC 107 Leather Shade change Grade 3 min. Staining Grade 3 min. Self-staining Grade 3 min. Fabric Shade change Grade 4 min. Staining Grade 4 min. Self-staining Grade 4 min. Colorfastness to Light – 20 AFU’s AATCC 16E

Fabric Grade 4 min. Leather Grade 3 min.

Colorfastness to Crocking AATCC 8 Light & medium shades Dry Grade 4 min. Wet Grade 3.5 min. Suedes & dark shades Dry Grade 3.5 min. Wet Grade 2.5 min. Puncture Resistance 3 lbs. minimum ASTM F1342 Report thickness of

material and force to puncture to nearest 0.01 lbs. (50 g)

Flex Resistance No cracking @ 10,000 cycles SATRA PM 101 Cold Flex No cracking @ -20°F ASTM D1790 Pilling Resistance Grade 4 min. ASTM D3512 ASTM D4970 ASTM D3511 UPH 106



Totes, Purses and Luggage, continued


Abrasion Resistance Fabric No significant change @ 500 cycles ASTM D3884 Piping No significant change @ 150 rubs ASTM D3886 Leather No significant change @ 500 cycles ASTM D3884 Water Resistance 1 gram max at AATCC 35 600 mm for 2 minutes Oil Repellency Grade A = Pass AATCC 118 Grade # 5 oil Water Repellency Bags & Wallets: 80 min AATCC 22 Luggage: 90 min Heavy Metals (Leather only) 100 ppm (mg/kg) Acid digestion &

Lead ICP/UV-VIS Cadmium Mercury Chromium VI Free Formaldehyde 150 ppm (mg/kg) DIN 53315 (Leather, PVC/PU and fabrics) Azo Dyestuff 30 ppm (mg/kg) LMBG §35 (Leather, PVC/PU and fabrics) B82.02-4 Disperse Dyes None allowed DIN NMP 512 WD (Leather and fabrics) Nickel 0.5 µg/cm²/week EN 1811 (Metal parts only) EN 12472



KITCHEN AND DINING Candles

(Including candles of all types)

EVALUATION REQUIREMENT TEST METHOD Labeling Country of Origin Verify actual FTC Manufacturer’s Identity (RN#) Verify actual FTC Product should carry the Visual Examination following wording or equivalent.

1. Keep out of reach of children. 2. Never leave burning candle unattended. 3. Keep wick trimmed to ¼” before lighting candles. 4. Burning candles should be kept away from curtains or other

flammable materials. 5. Place candle on heat resistant surface or us appropriate candle

holder. 6. Remove holder after cooling. The container may be hot. 7. Citronella Scented for insect repellent. (If applicable) 8. For outdoor use only (If applicable)

Lead Content Less than 0.06% by dry weight 16 CFR 1303 Workmanship No cracks, blisters or visual defects Visual examination No sharp points or rough edges while feeling product Base to be smooth and flat Resistance to Tipping No instability @ 10° Place at 10° angle and

release. Wick No metal core wicks Visual examination of No excessive clubbing at the tip wicks during burning of the wick during burning No exposed wick less than ¼" long Burning Characteristics Minimal to moderate dripping Burn candles 8 hours No smoke longer than 10 seconds per cycle for 5 days. Do Wick not to drown itself not trim wicks. Do not No flaring of wax pool pour out molten wax. Maximum flame height <2.5 in. Burn total of 40 hours or self extinguish, whichever occurs first.



Candles, continued

EVALUATION REQUIREMENT TEST METHOD Resistance to Ageing No visible color change or fading 40° C and 95% RH for 24 hours Candle Temperature Max temp. of surface not to Measurement by

exceed temperatures listed below thermocouple

Metal Ceramic/Glass Plastic Parts intended to be held 55°C 65°C 75°C Parts likely to be touched 105°C 120°C 125°C Base 110°C 125°C 135°C

Transfer temperature to Max temp of surface not to Measurement by surface holding candle exceed 120°F thermocouple between candle holder and furniture surface



KITCHEN AND DINING Candle Holders and Candelabras

(Including indoor and outdoor candle holders and candelabras made of all materials)

EVALUATION REQUIREMENT TEST METHOD Labeling: Country of Origin Verify actual FTC Manufacturer’s Identity (RN#) Verify actual FTC Flammability Less than 0.1"/sec. CFR 1500.44 Lead Content Less than 0.06% by dry weight 16 CFR 1303 (Painted surfaces only) Workmanship No cracks, blisters or visual defects Visual examination No sharp points or rough edges while feeling product Base to be smooth and flat Functional Use No visible damage, Operate for adjustable parts operate smoothly 24 hours - checking and remain securely in new at least 4 times position Tilt Resistance No tipping or instability Hold at 10° angle. Effects of Humidity No significant surface change 24 hours, 95% RH, 100°F Effects of Extreme Temperature No significant surface change 32°F for 24 hours and 120°F for 24 hours Surface scratching No scratching of other surfaces 5 cycles, 10" back & forth on wood, glass and plastic laminate Candle (cup) Holder Size Specific candle must fit securely Actual use Candle Temperature Max temp. of surface not to Measurement by

exceed temperatures listed below thermocouple

Metal Ceramic/Glass Plastic Parts intended to be held 55°C 65°C 75°C Parts likely to be touched 105°C 120°C 125°C Base 110°C 125°C 135°C

Candle Holders, continued




Transfer temperature to Max temp. of surface not to Measurement by surface holding candle exceed 120°F thermocouple between candle holder and furniture surface



KITCHEN AND DINING Cookware, Tools & Utensils

(Including, but not limited to, baking sheets, spoons, spoon rests, tortilla baskets, avocado slicers and salad spinners. Refer to the Appliances Product Standard for appliances.)

EVALUATION REQUIREMENT TEST METHOD Labeling Country of Origin Verify actual FTC Manufacturer’s Identity (RN#) Verify actual FTC Lead in Surface Coating <0.06% Pb by weight 16 CFR 1303 Food Contact Surface Toxicity Must comply with US FDA Indirect 21 CFR 175.300; 117 (Interior plastic/Silicon Coated Surfaces Only) Food Additives Regulations Leachable Lead and Cadmium on Pb <0.1 ppm (Hollowware) AOAC 973.32 Food Contact Surface Cd <0.08 ppm (Large Hollowware) ASTM C738 <0.01 ppm (all others) Functional Use No visible damage, Operate for adjustable parts operate smoothly 2 full use cycles and remain securely in new position Workmanship No cracks, blisters or visual defects Visual examination No sharp points or rough edges while feeling product Base to be smooth and flat Capacity As stated Standard measurement Report actual Dishwasher Safe No cracking, crazing, chipping or 10 cycles normal wash color change with detergent Microwave Safe No cracking, crazing or chipping Fill with water to 80% (Microwavable products only) capacity. Heat in oven

set at 1KW until ebullition occurs. Continue 3 additional minutes. Repeat for 2 more cycles.



Cookware, Tools and Utensils, continued

EVALUATION REQUIREMENT TEST METHOD Base Stability No separation of cladding Heat empty cookware to No visible convex shape on bottom 392°F and immerse into

cold water. Repeat for 10 cycles.

Handle Strength No breakage at weld joint Load with water 2.25

times gross weight. Raise 40 mm for 1,500 cycles.

Non-stick Performance No residue Prepare test pancakes (If applicable) and remove from

surface Abrasion Resistance No area of non-stick surface 250 cycles of

removed by abrasion reciprocating action and 15N downward force with nylon web cleaner; detergent added before abrasion started

Oven Safe No damage 500°F for metal handle, 350°F for plastic

handle, for 2 hours Resistance to Boil Dry No damage including shape change, Fill with 4 oz. water,

bubbles, cracks heat until dry. Continuously heat for additional 30 minutes



KITCHEN AND DINING Food Containers

(Including, but not limited to, frozen treat makers, herb keepers, salad molds and insulated cups)

EVALUATION REQUIREMENT TEST METHOD Labeling Country of Origin Verify actual FTC Manufacturer’s Identity (RN#) Verify actual FTC Lead in Surface Coating <0.06% Pb by weight 16 CFR 1303 Food Contact Surface Toxicity Must comply with US FDA Indirect 21 CFR 175.300; 117 (Interior plastic/Silicon- Coated Surfaces Only) Food Additives Regulations Leachable Lead and Cadmium on Pb <0.1 ppm (Hollowware) AOAC 973.32 Food Contact Surface Cd <0.08 ppm (Large Hollowware) ASTM C738 <0.01 ppm (all others) Workmanship No cracks, blisters or visual defects Visual examination No sharp points or rough edges while feeling product Base to be smooth and flat Functional Use No visible damage, Operate for adjustable parts operate smoothly 4 full use cycles and remain securely in position Capacity To be as stated Standard measurement Report actual Dishwasher Safe No cracking, crazing, chipping or 10 cycles normal wash color change with detergent Microwave Safe No cracking, crazing or chipping Fill with water to 80%

capacity. Heat in oven set at 1KW until ebullition occurs. Continue 3 additional minutes. Repeat for 2 more cycles.



Food Containers, continued

EVALUATION REQUIREMENT TEST METHOD Handle Strength No breakage at handle joint Load sample with mass

equivalent to 1.5 times the gross capacity of water. Lift the sample by the handle 10 times within 1 minute.

Stain Resistance No staining Expose surface to a (Dishwasher- safe items only) variety of kitchen

sauces for 12 hours. Subject product to 1 normal dishwasher cycle using detergent.

Effects of Extreme Temperature No significant surface change 32°F for 24 hours and (Plastic items only) 120°F for 24 hours Thermal Shock No cracking, chipping or crazing Heat empty in 350°F (Ceramic and glass items only) oven for 1 hour.

Submerge in 75°F water. Repeat for 4 cycles.

Resistance to Dropping No breakage 4 drops to vinyl floor (For plastic ware only) from 36" Lid Fit No leakage except from spout Fill with water to gross (For insulated products only) capacity, pour until

empty



KITCHEN AND DINING Tablecloths, Napkins, Place Mats & Table Runners

(Including, but not limited to, textile fiber and/or plastic table top products)

EVALUATION REQUIREMENT TEST METHOD Labeling Country of Origin Verify actual FTC Manufacturer’s Identity (RN#) Verify actual FTC Fiber Content Verify actual FTC Care Instructions Verify actual FTC Dimensional Change – 3HL AATCC 135 / 150 Natural Fibers Flannel ±5.0% max Corduroy ±4.5% max All others ±4.0% max Linings, if present ±1% of shell Synthetic Fibers Flannel ±4.5% max Corduroy ±4.0% max All others ±3.5% max Linings if present ±1% of shell General Appearance after No significant change Visual evaluation Laundering including surface, color, shape, etc Effects of Cleaning Solution Surface Appearance Grade 4 AATCC 124 Shade Change Grade 4 AATCC 61 or 132 Effects of Extreme Temperature No significant surface change 32°F for 24 hours and (Plastic items only) 120°F for 24 hours Colorfastness to Laundering (Washable items only) AATCC 61 Shade change Grade 4 min. Staining Grade 3.5 min. Self-staining Grade 5 min. Colorfastness to Bleach (Washable items only) Chlorine Grade 4 min. Spot Test Non-chlorine Grade 4 min. Soak Test



Table Top, continued

EVALUATION REQUIREMENT TEST METHOD Colorfastness to Light AATCC 16E 20 AFU exposure Non-neon Grade 3.5 min Neons & straw products Grade 3 min. 10 AFU exposure Silk Grade 4 min. Colorfastness to Water (Washable items only) AATCC 107 Shade change Grade 4 min. Staining Grade 3 min. Self-staining Grade 5 min. Colorfastness to Crocking AATCC 8 or 116 Light & medium shades Dry Grade 4 min. Wet Grade 3.5 min. Dark shades & Pigments Dry Grade 3.5 min. Wet Grade 2.5 min. Resistance to Yarn Slippage 20 lbs min. ASTM D1683 Seam Strength 20 lbs min. ASTM D1683 Fiber Content 3% tolerance AATCC 20 Fabric Count Report actual


Weight Report actual ASTM D3776



KITCHEN AND DINING Towels

(Including, but not limited to, Miracle- cloths, dish towels, bath towels, etc.)

EVALUATION REQUIREMENT TEST METHOD Labeling Country of Origin Verify actual FTC Manufacturer’s Identity (RN#) Verify actual FTC Fiber Content Verify actual FTC Care Instructions Verify actual FTC Dimensional Change – 3HL AATCC 135 / 150 Natural Fibers ±4.0% max Synthetic Fibers ±3.5% max General Appearance after No significant change Visual Evaluation Laundering including surface, color, shape, etc Colorfastness to Laundering AATCC 61 Shade change Grade 4 min. Staining Grade 3.5 min. Self-staining Grade 5 min. Colorfastness to Bleach Chlorine Grade 4 min. Spot Test Non-chlorine Grade 4 min. Soak Test Colorfastness to Light AATCC 16E Indoor towels 20 AFU’s Grade 4 min. Outdoor towels 40 AFU’s Grade 4 min. Colorfastness to Water AATCC 107 Shade change Grade 4 min. Staining Grade 3 min. Self-staining Grade 5 min. Colorfastness to Perspiration AATCC 15 Shade change Grade 4 min. Staining Grade 3 min. Self-staining Grade 5 min.



Kitchen and Dining – Towels, continued

EVALUATION REQUIREMENT TEST METHOD Colorfastness to Crocking AATCC 8 or 116 Light & medium shades Dry Grade 4 min. Wet Grade 3.5 min. Dark shades & Pigments Dry Grade 3.5 min. Wet Grade 2.5 min. Colorfastness to Seawater Grade 4 min. AATCC 106 (Beach towels only) Colorfastness to Chlorinated Grade 4 min. AATCC 162 Pool Water (Beach towels only) Absorbency 50% min. ASTM D4772 Pile Retention ASTM D4685 Back Grade 4 min. Face Grade 3 min. Fiber Content 3% tolerance AATCC 20 Fabric Count Report actual


Weight Report actual ASTM D3776



GIFTS AND GADGETS Games And Toys

(Including, but not limited to, games and toys for infants, children, teens and adults)

EVALUATION REQUIREMENT TEST METHOD Labeling Country of Origin Verify actual FTC Manufacturer’s Identity (RN#) Verify actual FTC Choking Hazard/Parts Verify actual ASTM F963/16CFR1500 Choking Hazard/Suffocation Verify actual ASTM F963/16CFR1500 Suggested age level Verify actual ASTM F963 Assembly Verify actual ASTM F963 Battery Markings Number of batteries required, ASTM F963 size and polarity of batteries Battery Use Instructions regarding the safe ASTM F963 disposal of batteries Heavy Metals on Surface Coating Meet requirements ASTM F963 (Toys) Lead Content on Paints and <0.06% by dry weight 16 CFR 1303 Surface Coatings Packaging film Shall be >0.03175 mm ASTM F963 Workmanship No cracks, blisters or Visual Examination visual defects. Construction and Design No sharp points, rough edges ASTM F963 use and abuse No small parts (for ages under 3 years) Meet all requirements Functionality No visible defect 20 full use cycles or Remain functional 8 hours continuous

use

Stuffing Cleanliness (Stuffed Toys) Free of insect, bird, rodent, AOAC Method etc. infestation & contaminants. Free of splinters, chips, dirt, etc. Must meet requirements Stuffing Cleanliness (Stuffed Toys) Natural and/or synthetic fiber Pennsylvania Regulation fill must meet requirements Games and Toys, continued


GOLD VIOLIN QUALITY GUIDELINES EVALUATION REQUIREMENT TEST METHOD DEHP (DOP) Content in PVC Must meet requirement ASTM F963 Component Flammability Pass ASTM F963/16 CFR 1500



GIFTS AND GADGETS

(Including teen and adult items only)

EVALUATION REQUIREMENT TEST METHOD Labeling Country of Origin Verify actual FTC Manufacturer’s Identity (RN#) Verify actual FTC Lead Content on Paints and <0.06% by dry weight 16 CFR 1303 Surface Coatings Workmanship No cracks, blisters or visual defects Visual examination No sharp points or rough edges while feeling product Base to be smooth and flat Construction and Design No sharp points, rough edges Visual Examination Meet all requirements Material – Flammability (Solids) Meet requirements ASTM F963 16 CFR 1500.44 Material – Flammability (Textiles) Meet requirements ASTM F963 16 CFR 1610 Safety on Battery- Operated Toys Meet requirements ASTM F963 Stuffing Cleanliness (Stuffed Toys) Free of insect, bird, rodent, AOAC Method etc. infestation and contaminants. Free of splinters, chips, dirt, etc. Must meet requirements Stuffing Cleanliness (Stuffed Toys) Natural and/or synthetic fiber Pennsylvania fill should meet requirements Regulation DEHP (DOP) Content in PVC Must meet requirement ASTM F963 Component



PET PRODUCTS Safety Guidelines

(Including, but not limited to, pet beds, dog tags, battery- operated toys, pet trainers, pet car seats, feeding stations, pet apparel, etc.)

This guideline is limited to the safety aspects necessary for pet products. All pet products

are also subject to performance criteria as noted under related specific guidelines.

EVALUATION REQUIREMENT TEST METHOD Labeling Country of Origin Verify actual FTC Manufacturer’s Identity (RN#) Verify actual FTC Textile Fiber Content Verify actual FTC Apparel Care Instructions Verify actual FTC Safety Labeling Must be present as noted below Battery- operated toys Keep away from water. Do not submerge. Do not use in wet areas. Inspect periodically for damage. Items with remote controls Do not allow pet to play with power unit. Laser products Avoid direct eye exposure. Toys with diameter in any Not intended for unsupervised use. direction less than 4" Inspect periodically for damage. Soft toys This toy not intended for aggressive chewing pets. Inspect periodically for damage. Discard when worn. All toys Do not allow pets to play with broken, worn or damaged toys. Small parts attachment 15 lbs. for 10 sec. ASTM PS79 Sharp points & edges None present ASTM F 963 16 CFR 1500 Lead Content on Paints and <0.06% by dry weight 16 CFR 1303 Surface Coatings



YARD AND GARDEN Apparel – Outdoor

(Including, but not limited to, aprons, hats, etc.)

EVALUATION REQUIREMENT TEST METHOD Labeling Country of Origin Verify actual FTC Manufacturer’s Identity (RN#) Verify actual FTC Fiber Content Verify actual FTC Care Instructions Verify actual FTC Dimensional Change – 3HL AATCC 135 / 150 Natural Fibers Flannel ±5.0% max Corduroy ±4.5% max All others ±4.0% max Linings, if present ±1% of shell Synthetic Fibers Flannel ±4.5% max Corduroy ±4.0% max All others ±3.5% max Linings, if present ±1% of shell General Appearance after No significant change Visual evaluation Laundering including surface, color, shape, etc. Colorfastness to Laundering AATCC 61 Shade change Grade 4 min. Staining Grade 3.5 min. Self-staining Grade 5 min. Colorfastness to Bleach Chlorine Grade 4 min. Spot Test Non-chlorine Grade 4 min. Soak Test Colorfastness to Light AATCC 16E 40 AFU exposure Non-neon Grade 3 min. Neons & straw products Grade 3 min. Colorfastness to Water AATCC 107 Shade change Grade 4 min. Staining Grade 3 min. Self-staining Grade 5 min.



Apparel-Outdoor, continued EVALUATION REQUIREMENT TEST METHOD

Colorfastness to Perspiration AATCC 15 Shade change Grade 4 min. Staining Grade 3 min. Self-staining Grade 5 min. Colorfastness to Crocking AATCC 8 or 116 Light & medium shades Dry Grade 4 min. Wet Grade 3.5 min. Dark shades & Pigments Dry Grade 3.5 min. Wet Grade 2.5 min. Seam Strength 20 lbs min. ASTM D1683 Yarn Slippage 20 lbs min. ASTM D1683 Tensile Strength 30 lbs min. ASTM D5034 Tear Strength 2 lbs min. ASTM D1424 Fiber Content 3% tolerance AATCC 20 Fabric Count Report actual


Weight Report actual ASTM D3776 Water Repellency (water repellent outerwear only) AATCC 22

As received 90 min. After laundering 70 min.

Water Resistance (water resistant outerwear only) 1 gm max at 600mm AATCC 35 for 2 minutes Free Formaldehyde 150 ppm (mg/kg) DIN 53315 (Leather, PVC/PU and fabrics) Azo Dyestuff 30 ppm (mg/kg) LMBG §35 (Leather, PVC/PU and fabrics) B82.02-4 Disperse Dyes None allowed DIN NMP 512 WD (Leather and fabrics) Flammability Class I 16 CFR 1610



YARD AND GARDEN Cleaners And Chemicals

(Including, but not limited to, air freshener, insect repellent, pond cleaner, spot & stain cleaners, Zap, toilet bowl cleaners)

EVALUATION REQUIREMENT TEST METHOD Labeling Country of Origin Verify actual FTC Manufacturer’s Identity (RN#) Verify actual FTC Strong sensitizers Verify actual 16 CFR 1500 Hazardous substances Verify actual 16 CFR 1500 Weight, contents Standard Measurement Report Actual Weight Chemical components Report Actual Chemical analysis of Not to be on banned list contents Functional Use Functions as intended Actual use (Whenever possible) pH Report actual AATCC 81 Toxicity Pass 16 CFR 1500.42 (Skin- contact items only)



YARD AND GARDEN Flexible Accessories

(Including, but not limited to, furniture covers, bunting and hoses)

EVALUATION REQUIREMENT TEST METHOD Labeling Country of Origin Verify actual FTC Manufacturer’s Identity (RN#) Verify actual FTC Lead Content on Paints and <0.06% by dry weight 16 CFR 1303 Surface Coatings Workmanship No cracks, blisters or visual defects Visual Examination No sharp points or rough edges Base to be smooth and flat Functional Use No visible damage, Operate for adjustable parts operate smoothly 48 hours with four and remain securely in new adjustments to any position moveable part - checking at 4 hour intervals Resistance to Tipping No instability @ 10° Hold at 12° angle and (If applicable) release. If tipping

occurs, hold at 10° angle and release.

Colorfastness to Light (60 AFUs) Grade 3 min. AATCC 16E Colorfastness to Water Grade 4.5 min. AATCC 107 Effects of Humidity No significant surface change 24 hours, 95% RH, 100°F Effects of Extreme Temperature No significant surface change 32°F for 24 hours and 120°F for 24 hours



YARD AND GARDEN Hard

(Including, but not limited to, free standing ornaments, floating ornaments, non-electric fountains, water stations, flag poles, hose holders, pots & planters, sprinklers, pet ramps,

decorative sculptures and bird feeders)

EVALUATION REQUIREMENT TEST METHOD Labeling Country of Origin Verify actual FTC Manufacturer’s Identity (RN#) Verify actual FTC Lead Content on Paints and <0.06% by dry weight 16 CFR 1303 Surface Coatings Workmanship No cracks, blisters or visual defects Visual Examination No sharp points or rough edges Base to be smooth and flat Functionality No visible defect 200 full use cycles or Remain functional 48 hours continuous

use Colorfastness to Light Grade 3 min. AATCC 16E (60 AFU’s) Colorfastness to Water Grade 4.5 min. AATCC 107 Stability Must be level and stable when Visual Examination

placed on flat surface Tilt Resistance No tipping or instability Hold at 12° angle. (Freestanding items only) If tipping occurs, retest at 8° angle. Report any 8° failures Breakage Resistance No breakage One 3 ft. drop to (Ceramics not included) Remain functional concrete surface



Yard Accessories – Hard, continued

EVALUATION REQUIREMENT TEST METHOD Impact Resistance No breakage or separation Attach 3 oz. steel ball to (Glass and ceramic items only) string. Hold 3 in. away from product. Release ball to impact product. Cycle 4 times. Corrosion Resistance No significant corrosion ASTM B117 Salt spray for 24 hours Effects of Humidity No significant surface change 24 hours, 95% RH, 100°F Effects of Extreme Temperature No significant surface change 32°F for 24 hours and 120°F for 24 hours


gold violin quality guidelines table of...

Documents