huawei optix osn 7500ii - tc-systems.net · huawei technoloies co ltd all in one solution based on...

HUAWEI TECHNOLOGIES CO., LTD.

All in One Solution Based on Universal Switch and Transport

Unique architecture that integrates PCM, TDM, Ethernet, WDM and

MPLS-TP technology.

Universal switch at any level of packet and TDM in their original

format, high efficiency and best performance, ‘0’ waste of

bandwidth.

Universal transport in one port with smart 40G line card, carefree

evolution among different types of services, ‘0’ waste of investment.

MPLS-TP for Highly Efficient and Highly Available Packet Transport

Guaranteed Performance from end-to-end committed bandwidth

mechanism.

99.999% availability: 50ms recovery for both linear and ring

applications.

SDH-like OAM mechanism capable of fast detection and

troubleshooting, including end-to-end performance monitoring.

PID inside for Tailored Metro Ultra Broadband Transport

Integrating OTU, MUX and DEMUX boards by a PID (photonics

integrated device) chip, providing 40G/100G capacity per port and

larger in future.

Huawei OptiX OSN 7500II

Universal Transport Platform for Metro Aggregation & Core

• Large Capacity: 320G Packet / 360G TDM universal switch, 16 service

processing slots and 16 service interface slots.

•Ultra Broadband: Smart 40G line transport, 100G line ready.

• Integrated OTN Switching: 560G capacity, OTU-1,OTU-2/2e interface.

SDH-like O&M without complicated photonic layer design such as

wavelength planning and OSNR calculating, with less patch cords

and fiber operations, time to market greatly reduced.

50% footprint saving and 50% power consumption reduction.

TP-Assist for Easy O&M MPLS-TP based O&M solution ‘TP-Assist’ providing efficient

planning, fast deployment and easy maintenance, making the large-

scale packet network easily manageable

Traffic based crystal clear O&M is supported with visual network-

level view, graphical format to display end-to-end service

configuration, performance and status.

Maintenance experience even better than SDH: visualized end-to-

end bandwidth management, intelligently locating 92% failure,

analyzable and predicable network management

Industrial Certifications Ensure Reliable Operation Compliant with EN 50121-4, IEC 61850-3, IEC 61000-6-5, IEEE 1613

Copyright © Huawei Technologies Co., Ltd. 2016. All rights reserved.

THIS DOCUMENT IS FOR INFORMATION PURPOSE ONLY, AND DOES NOT CONSTITUTE ANY KIND OF WARRANTIES.

Specifications OSN 7500 II

Dimensions 800mm (H) x 496mm (W) x 295mm (D)

Switch Capacity Packet: 320 Gbit/s and TDM: 360 Gbit/s (higher order), 40 Gbit/s (lower order), OTN: 560Gbit/s

Service Slots 32 slots, 16 slots for interface boards and 16 slots for processing boards with same bandwidth per slot

Supported Interface

OTN interface OTU-1, OTU-2/2e, OTU-3(40G, compliant with OTL3.4 standard)

Ethernet interface FE/GE/10GE/40GE

SDH interface STM-1/4/16/64

PDH interface E1/T1, E3/T3, E4

ATM interface E1, STM-1

WDM interface40 DWDM wavelengths, compliant with ITU-T G.694.18 CWDM wavelengths, compliant with ITU-T G.694.2

SAN interface FDDI, ESCON, FICON/FICON Express, FC100/200/400/800/1200

PCM interfaceFXS/FXO, 2/4W VF & E&MX.21/V.35/V.11/V.24/V.28, RS232/RS422, RS449/RS423A/RS422A, RS530/RS530A,RS485, G.703 64 kbit/s codirectional

Other interface DDN, Video

Networking ModeSupports packet, hybrid (packet + SDH or OTN + SDH) or SDH networkingSupporting WDM networkingSupporting single-fiber bidirectional transmission

Power Supply -48V DC/-60V DC

Operation Environment

Temperature Relative HumidityLong term: 0ºC ~ 45ºC 5% ~ 85%Short term: -5ºC ~ 55ºC 5% ~ 95%

Ethernet Feature

E-Line and E-LAN, QinQMPLS-TP based VPWS and VPLSMulti-section pseudo-wire (MS-PW)ETH PWE3, TDM PWE3, ATM/IMA PWE3IGMP Snooping V2Blacklist, Broadcast packet suppression, ACLVLAN SWAP

PCM Feature

Voice or data Conference/Meeting,P2MP,MP2MPFXO/FXS mode can be set by softwareE&M Interface voltage can be set by software (-48V/-12V)E&M signaling can be set by software (Bell types I, II, III, IV, V and British Telecom SSDC5)

QoS

Hierarchical QoS scheduling and traffic shapingDiffServ mode based on traffic classification, eight priority queuesSimple traffic classification, complex traffic classification, per hop behavior (PHB),and ACLCommitted access rate (CAR), shaping based on port scheduling priorityPQ scheduling priority, weighted fair queuing (WFQ) and PQ+WFQ queuingTail drop and weighted random early detection (WRED)

OAM

MPLS-TP OAM

LSP/PW OAM:CC, LB, LTAIS, RDILM, DM LCK, TSTCSF

MPLS OAMLSP/PW OAM: FDI, BDI,CV, FFD, TraceRoute, Ping, LM, DMPW OAM: CES PW VCCV

Ethernet OAM ETH-CC, ETH-Loopback, ETH-Link Trace, Remote Loopback, Remote Fault Detection, RMON(RFC 2819)

Protection

Equipment-level Protection Universal Cross-Connect, System Control and Clock Processing Board 1+1 backup and power 1+1 backup

MPLS-TP based Service Protection

LSP/PW Linear protection, Ring protectionAnti multifailure protection based on MS-PWLAG, MC-LAG, Dual-homing protection, LPT

SDH based Service Protection

2/4 fiber MS-SP Ring; 1+1/1:n (n<=14) Linear MSPSNCP/SNCTP Tributary protection for E1/T1, E3/T3, E4, STM-1(e) and FE

ASONDistributed restorable rerouting protection5-level service dedicated protection scheme based on different SLA: Diamond, Gold, Silver, Copper and Iron servicesBased on VC-4 and VC-12 granularity

Synchronization

Both Ethernet and SDH networks supporting clock synchronizationSupporting G.813, Synchronous Ethernet and IEEE 1588v2 synchronization Adaptive clock recovery (ACR)Two external clock inputs/outputs (2 MHz or 2 Mbit/s)Two external time signals (1pps+TOD)

Huawei OptiX OSN 7500II


OptiX OSN 580 — Universal Transport Platform

• Small Size, Large Capacity: 5U height, 560G or 280G switch capacity

• Converge L0/L1/L2: Ethernet/MPLS-TP, TDM and WDM. One platform provides both soft- and hard-pipe functionality

• Converge Ultra Bandwidth: SMART 40G line rate

• Converge Next-Generation PCM/MUX: Evolving network with low-speed interfaces

• Converge MPLS-TP: Simplifies large-scale packet-switched networks

Universal Platform with Soft and Hard Pipes Universal switching: TDM and packet service switching with a universal switch fabric

Unified access: Including SCADA, Voice, Clock, Teleprotection, OA,MIS and CCTV/Video Services

Hard pipe: Physical Separation and high QoS to ensure service security and reliability

Soft pipe: Statistical multiplexing to efficiently carry high-bandwidth data services

The Huawei OptiX OSN 580 is a new-generation universal transport platform. It adopts a unified switching architecture and supports any mix of

traffic, from all-circuit to all-packet. The OSN 580 offers a converged, reliable and cost-efficient transport platform to meet the needs of mission-

critical applications such as control and monitor energy and distribution grids, gas and oil pipelines, railways and authorities.

Product overview

Features and benefits

OptiX OSN 580

SMART 40G Meets High Bandwidth Requirements 40G: Integrates OTU, MUX and DEMUX boards using a PID (photonics integrated device), providing 40G capacity per port, which will later be expanded to 100G

SMART: Supports any mix of TDM & Packet service transport on each port, allowing evolution from 100% TDM to 100% packet

Free optical layer design: No complicated photonic layer design, such as wavelength planning or OSNR calculation

Long-Haul transmission: Distance up to 240km with amplifiers, up to 80km without amplifier

Next-Generation PCM/MUX Simplifies NetworksAll-in-One Solution

Reduces stacking of different devices, simplifying network layers

With universal transport platform that support all applications, easy to expand and evolve

Unified management, end-to-end service configuration, and easy troubleshooting

Highly integrated design

Provides high-integration PCM boards with multiple interfaces, including AT8, FXSO12, and DXM, 3 cards provide the functionality of traditional 11 cards

Leading Evolution to All-IP Networks

Based on universal switch fabric, the customer could establish a universal transport network or end-to-end packet network, achieving the network migration from TDM to all-IP smoothly

MUXN x 10G SDH card

N x 10GE Packet card

SMART 40G Line Card

DEMUX

Phone PCPBXRTU

PCM Board

PCM Equipment Transport Equipment

Teleprotection

AT8: 2/4W VF & E&M Single card for 2/4W E&M All the parameter software

configurable, without jumper E&M Type I, II, III, IV & V, SSDC5 Voltage -12V and -48V 2W and 4W VF

FXSO12: Single card for FXS and FXO Software configurable

DXM: Any rate access One card for any rate From 9.6Kbps to N*64Kbps Support 64K Co-Dir

4 cards to 1 card 4 cards to 1 card3 cards to 1 card

2/4W VF 64K Co-DirE&MType M

E&MType N

9.6K~64Kbps

FXS FXO Ring CardPower FeedCard

N*64Kbps Conference Card

OptiX OSN 580

MPLS-TP and TP-Assist Achieve High Efficiency and Easy RolloutMultiprotocol Label Switching-Transport Profile (MPLS-TP), a connection-oriented packet transport technology that is decoupled from IP and combines the transport requirements such as strong OAM and protection. By using MPLS-TP, the customer will have the following benefits when addressing their transition to packet networks.

Guaranteed Performance from end-to-end committed bandwidth mechanism

99.999% availability: 50 ms recovery for both linear and ring applications

SDH-like OAM mechanism provides capable of fast detection and troubleshooting, including end-to-end performance monitoring

MPLS-TP based O&M solution TP-Assist provides efficient planning, fast deployment and easy maintenance, making the large-scale packet network easily manageable


ApplicationsThe OSN 580 provides reliable and flexible transmission of real-time and critical services using high-efficiency soft pipe and high-quality hard pipe.

Universal Transport Solution For Power Grid

Universal Transport Solution For Subway



Specifications OSN 580

Dimensions 221 mm (H) x 442 mm (W) x 224 mm (D)

Installation method In a cabinet (including ETSI, 19-inch and 23-inch cabinets), in an outdoor cabinet

Switching capacityPacket: 560 Gbit/s, TDM: 280 Gbit/s (higher order)Packet: 280 Gbit/s, TDM: 280 Gbit/s (higher order)

Service slots 15 slots

Supported interfaces

OTN interface OTU-2, OTU-3

Ethernet interface FE/GE/10GE/40GE

SDH interface STM-1/4/16/64

PDH interface E1/T1, E3/T3

PCM interfaceFXS/FXO, 2/4 wire audio and E&MX.21/V.35/V.11/V.24/V.28, RS232/RS422, RS449/RS423A/RS422A, RS530/RS530A, RS485, G.703 64 kbit/s bidirectional; IEEE C37.94


Networking modesSupports pure packet, hybrid (packet + SDH), or SDH networkingSupports WDM networking

Power supply-48 V DC/-60 V DC220 V AC/110 V AC

Operation environment

Temperature Relative HumidityLong term: -5ºC ~ 50ºC 5% ~ 85%Short term: -10ºC ~ 55ºC 5% ~ 95%

Ethernet and MPLS-TP features

E-Line, E-LAN, and QinQMPLS-TP based VPWS and VPLSMS-PWETH PWE3IGMP Snooping v2

PCM features

Supports 64K cross connectVoice or data conference, Point-to-Point, Point-to-Multipoint, Multipoint-to-MultipointFXO/FXS mode can be set by softwareE&M signaling can be set by software (types I, II, III, IV, V and British Telecom SSDC5)

QoS

Hierarchical QoS scheduling and traffic shapingDiffServ mode based on traffic classificationSimple traffic classification, complex traffic classification, per-hop behavior (PHB), and ACLCommitted access rate (CAR)PQ scheduling priority, weighted round robin (WRR), and PQ+WRR queuingTail drop and weighted random early detection (WRED)Shaping based on port scheduling priority

OAMMPLS-TP OAM

CC, LB, LTAIS, RDILM, DM LCK, TSTCSF

Ethernet OAM ETH-CC, ETH-loopback, ETH-link trace, remote loopback, remote fault detection, RMON (RFC 2819)

Protection

Equipment-level protection 1+1 backup for cross-connect, system control, clock processing board, and power unit

MPLS-TP-based service protection

LSP/PW linear protection, ring protectionAnti-multiple failure protection based on MS-PWLAG, MC-LAG, Dual-homing protection, LPT, ERPS

SDH-/PDH-based service protection

Linear MSP and MSP ringSNCPE1 1+1 SNCP E1/T1 1+1 tributary protection switch (TPS)

Synchronization

Supports G.813, Synchronous Ethernet, and IEEE 1588v2 synchronization Adaptive clock recovery (ACR)Two external clock inputs/outputs (2 MHz or 2 Mbit/s)Two external time signals inputs/outputs (1pps+TOD)

OptiX OSN 580


• Small Size, Large Capacity: 2U height, 64G Packet / 20G TDM universal switch

• Converge L0/L1/L2: Ethernet/MPLS-TP, TDM and WDM. One platform provides both soft- and hard-pipe functionality

• Converge Next-Generation PCM/MUX: Evolving network with low-speed interfaces

• Converge MPLS-TP: Simplifies large-scale packet-switched networks

• High operating temperature: up to 65℃

Product overview

Features and benefits

The Huawei OptiX OSN 550 is a compact, easy to operate universal transport platform. The OSN 550 offers a converged, reliable and cost-efficient transport platform to meet the needs of mission-critical applications such as control and monitor energy and distribution grids, gas and oil pipelines, railways and authorities

Universal Platform with Soft and Hard Pipes

Universal switching: TDM and packet service switching with a universal switch fabric

Unified access: Including SCADA, Voice, Clock, Teleprotection, OA,MIS and CCTV/Video Services

Hard pipe: Physical Separation and high QoS to ensure service security and reliability

Soft pipe: Statistical multiplexing to efficiently carry high-bandwidth data services

OptiX OSN 550 — Universal Transport Platform



OptiX OSN 550

All-in-One Solution

Reduces stacking of different devices, simplifying network layers

With universal transport platform that support all applications, easy to expand and evolve

Unified management, end-to-end service configuration, and easy troubleshooting

Highly integrated design

Provides high-integration PCM boards with multiple interfaces, including AT8, FXSO12, and DXM , 3 cards provide the functionality of traditional 11 cards

Next-Generation PCM/MUX Simplifies Networks

Phone PCPBXRTU

PCM Board

PCM Equipment Transport Equipment

Teleprotection

AT8: 2/4W VF & E&M Single card for 2/4W & E&M All the parameter software

configurable, without jumper E&M Type I, II, III, IV & V,SSDC5 Voltage -12V and -48V 2W and 4W VF

FXSO12 Single card for FXS and FXO Software configurable

DXM: Any rate access One card for any rate From 9.6Kbps to N*64Kbps Support 64K Co-Dir

4 cards to 1 card 4 cards to 1 card3 cards to 1 card

2/4W VF 64K Co-DirE&MType M

E&MType N

9.6K~64Kbps

FXS FXO Ring CardPower FeedCard

N*64Kbps Conference Card

Leading Evolution to All-IP Networks

Based on universal switch fabric, the customer could establish a universal transport network or end-to-end packet network, achieving the network migration from TDM to all-IP smoothly

MPLS-TP Achieve High Efficiency and Easy RolloutMultiprotocol Label Switching-Transport Profile (MPLS-TP), a connection-oriented packet transport technology that is decoupled from IP and combines the transport requirements such as strong OAM and protection. By using MPLS-TP, the customer will have the following benefits when addressing their transition to packet networks.

Guaranteed Performance from end-to-end committed bandwidth mechanism

99.999% availability: 50 ms recovery for both linear and ring applications

SDH-like OAM mechanism provides capable of fast detection and troubleshooting, including end-to-end performance monitoring

MPLS-TP based O&M solution TP-Assist provides efficient planning, fast deployment and easy maintenance, making the large-scale packet network easily manageable




OptiX OSN 550



Installation method In a cabinet (including ETSI, 19-inch and 23-inch cabinets), in an outdoor cabinet

Switching capacity Packet: 64 Gbit/s ,TDM: 20 Gbit/s (higher order)



Ethernet interface FE/GE/10GE

SDH interface STM-1/4/16

PDH interface E1/E3; T1/T3

CES interface ATM/IMA E1, ch STM-1

PCM interfaceFXS/FXO, 2/4 wire audio and E&MX.21/V.35/V.11/V.24/V.28, RS232/RS422, RS449/RS423A/RS422A, RS530/RS530A, RS485, G.703 64 kbit/s bidirectional; IEEE C37.94


Networking modesSupports pure packet, hybrid (packet + SDH), or SDH networkingSupports WDM networking

Power supply-48 V DC/-60 V DC220 V AC/110 V AC

Operation environment

Temperature Relative HumidityLong term: -5ºC ~ 55ºC 5% ~ 85%Short term: -5ºC ~ 65ºC 5% ~ 95%

Ethernet Feature

E-Line ,E-LAN and QinQMPLS-TP based VPWS and VPLS MS-PWETH PWE3IGMP Snooping v2Blacklist, Broadcast packet suppression, ACL

PCM features

Supports 64Kbps timeslot cross-connectingVoice or data conference, Point-to-Point,Point-to-Multipoint,Multipoint-to-MultipointFXO/FXS mode can be set by softwareE&M signaling can be set by software (types I, II, III, IV, V and British Telecom SSDC5)

QoS

Hierarchical QoS scheduling and traffic shapingDiffServ mode based on traffic classification Simple traffic classification, complex traffic classification, per hop behavior (PHB), and ACLCommitted access rate (CAR)PQ scheduling priority, weighted round robin (WRR) and PQ+WRR queuingTail drop and weighted random early detection (WRED)Shaping based on port scheduling priority

OAMMPLS-TP OAM

CC, LB, LTAIS, RDILM, DM LCK, TSTCSF


Protection

Equipment-level Protection Universal Cross Connection, System Control and Clock Processing Board 1+1 backup and power 1+1 backup

MPLS-TP based network-level Protection

LSP/PW Linear protection, Ring protectionAnti multifailure protection based on MS-PWLAG, MC-LAG, Dual-homing protection, LPT ERPS,ML-PPP, MSTP

SDH-/PDH-based service protection

Linear MSP and MSP ringSNCPE1 1+1 SNCP E1/T1 1+1 tributary protection switch (TPS)

Synchronization

Supports G.813, Synchronous Ethernet, and IEEE 1588v2 synchronization Adaptive clock recovery (ACR)Two external clock inputs/outputs (2 MHz or 2 Mbit/s)Two external time signals inputs/outputs (1pps+TOD)


MPLS-TP for Highly Efficient and Highly Available Packet Transport

Guaranteed Performance from end-to-end committed bandwidth

mechanism.

99.999% availability: 50ms recovery for both linear and ring

applications.

SDH-like OAM mechanism for quick fault detection, troubleshooting

and end-to-end performance monitoring.

Flexible installation 1U high box

Fitting 19/23’ rack, outside cabinet, wall, desk and pole mounting.

AC or DC power supply

Huawei OptiX OSN 500

MPLS-TP based CPE for Metro Access •Multi service access: PDH, SDH, Ethernet, CES, ATM/IMA etc

• Low Power Consumption: 35 W (typical)

•High operating temperature: up to 65ºC

TP-Assist for Easy O&M MPLS-TP based O&M solution ‘TP-Assist’ providing efficient

planning, fast deployment and simple maintenance, making the

large-scale packet network easily manageable

Traffic based crystal clear O&M is supported with visual network-

level view, graphical format to display end-to-end service

configuration, performance and status.

Better maintenance experience even than SDH: visualized end-to-

end bandwidth management, intelligently locating 92% failure,

analyzable and predicable network management






Switch capacity Packet: 7.2 Gbit/s and TDM: 21.25 Gbit/s (higher order), 5 Gbit/s (lower order)



Ethernet interface FE/GE

SDH interface STM-1/4

PDH interface E1/E3; T1/T3

CES interface ATM/IMA E1, ch STM-1

Networking ModeSupporting pure packet or SDH networking

Supporting single-fiber bidirectional transmission

Power Supply 48V DC/ -60V DC, 220V AC/110V AC

Operation

Environment

Temperature Relative Humidity

Long term: -5ºC ~ 45ºC 5% ~ 85%

Short term: -5ºC ~ 55ºC 5% ~ 95%

Ethernet Feature

E-Line, E-LAN and QinQ

MPLS-TP based VPWS and VPLS

MS-PW

ETH PWE3

IGMP Snooping v2

Blacklist, Broadcast packet suppression, ACL

QoS

Hierarchical QoS scheduling and traffic shaping

DiffServ mode based on traffic classification

Simple traffic classification, complex traffic classification, per hop behavior (PHB), and ACL

Committed access rate (CAR)

PQ scheduling priority, weighted round robin (WRR) and PQ+WRR queuing

Tail drop and weighted random early detection (WRED)

Shaping based on port scheduling priority

OAMMPLS-TP OAM

LSP/PW OAM:

CC, LB, LT

AIS, RDI

LM, DM

LCK, TST

CSF


Protection

Equipment-level

Protectionpower 1+1 backup

MPLS-TP based network-

level Protection

LSP/PW Linear protection, Ring protection

Anti multifailure protection based on MS-PW

LAG, MC-LAG, Dual-homing protection, LPT

ERPS, MSTP

SDH based network-level

Protection

2 fiber MS-SP Ring

1+1/1:n (n<=5) Linear MSP,SNCP

LAG, LPT, LCAS

Synchronization

Both Ethernet and SDH networks supporting clock synchronization

Supporting G.813, Synchronous Ethernet and IEEE 1588v2 synchronization

Adaptive clock recovery (ACR)

One external clock inputs/outputs (2 MHz or 2 Mbit/s)

Two external time signals(1pps+TOD)

Huawei OptiX OSN 500

huawei optix osn 7500ii - tc-systems.net · huawei technoloies co ltd all in one solution based on...

Documents