ieee 802.11 a/n wireless cpe product...

WWW.ZCOM.COM.CN - 1 -

IEEE 802.11 a/n Wireless CPE

Product Specification

Model Name: ZN-7200-2AEI-O

Version: 0.1


1 Revision History Date Version Author Description 2013/10/14 V0.1 Nancy 1st release version


2 Specification

2.1 Hardware Specification

The Hardware specifications of the product are as below:

Table 2-1 Hardware Specification Features Additional Information

Chipset Solution CPU: AR9342 RF: AR9342

Standard Compliance - IEEE802.3u MDI / MDIX 10/100 Fast Ethernet - IEEE802.11a/n wireless LAN interface - IEEE 802.11n wireless LAN standard

DDRII 64Mbyte Flash 16Mbyte Power input requirement Passive PoE 15V

Pin 4,5 VDC+ Pin 7,8 VDC-

Ethernet PHY 10/100 Mbps

Antenna Default external 5 dBi Omni antenna Antenna Connector SMA x2 LAN port 1port Reset Button Reset to factory default

Ground Ground terminal x1 System Update Capability - Support Web-UI upgrade via Ethernet port or wireless network

- Support TFTP upgrade via Ethernet port LED Definition

Power (Single-color LED x1) Green On: Power / system on Green Off: power / system off

LAN (Single-color LED x1) Off: No Ethernet connection detected Green On: Ethernet connection detected Green Blinking: Sending / receiving data

5G WLAN (Single-color LED x1) Green Off: WLAN disabled Green On: WLAN enable Green Blinking: WLAN data transmit

Signal *3 (Single-color LED x3) Excellent: 3 LED Green ON Good: 2 LED Green ON Weak: 1 LED Green ON

Data Rate 11a: 54M, 48M, 36M, 24M, 18M, 12M, 9M, 6Mbps auto fallback 11n: HT20 MCS0~15 HT40 MCS0~15

Data modulation type DSSS/BPSK/QPSK/CCK/DQPSK/DBPSK 802.11a: OFDM 802.11n: OFDM

RF frequency range FCC : 5725-5850 MHz CE: 5470-5725 MHz (DFS band)

Power Consumption (W) <12W


Average Output Power @ 25℃ (Single Chain) (± 2dBm) 1 2

802.11a 6, 9, 12, 18, 24Mbps 23dBm 36Mbps 22dBm 48, 54Mbps 21dBm

802.11an At HT20

MCS0, MCS8 24dBm MCS1, MCS2, MCS3, MCS9, MCS10, MCS11

23dBm

MCS4, MCS12 22dBm MCS5, MCS13 21dBm MCS6, MCS7, MCS14, MCS15

20dBm

802.11an At HT40

MCS0, MCS8 21dBm MCS1, MCS2, MCS3, MCS9, MCS10, MCS11

21dBm

MCS4, MCS12 21dBm MCS5, MCS13 21dBm MCS6, MCS7, MCS14, MCS15

20dBm

Sensitivity (at single chain) Mode 11a 11n HT20 11n HT40 6Mbps ≧ -89 9Mbps ≧ -88 12Mbps ≧ -85 18Mbps ≧-83 24Mbps ≧ -80 36Mbps ≧ -76 48Mbps ≧ -71 54Mbps ≧ -70 MCS 0/8 ≧ -83 ≧ -80 MCS 1/9 ≧ -80 ≧ -77

MCS 2/10 ≧ -78 ≧ -75 MCS 3/11 ≧ -75 ≧ -72 MCS 4/12 ≧ -71 ≧ -68 MCS 5/13 ≧ -67 ≧-64 MCS 6/14 ≧ -66 ≧ -63 MCS 7/15 ≧ -65 ≧ -62

1. The listed value is the target power calibrated in the card. The actual power will vary depending on each country’s regulation. For detailed CTL

table settings please contact our sales representative. 2. The output power been measured from U.FL connector without RF cable loss.


2.2 Firmware Specification

The Firmware Specifications of ZN-7200-2AEI-O as below:

Function Catalog Detail Function Default settings Web Language English English Status Information

Connections Statistics ARP Table Bridge Table DHCP Client List Network Activity

System Basic Settings: 1. Device Mode 2. Device Name 3. Ethernet DateRate 4. Network Modes 5. Country/Region 6. Spanning Tree (STP) 7. STP Forward Delay 8. GPS Coordinate

apXXXXXX Auto Bridge United States Enable 1 (second)

TCP/IP Settings (Bridge Mode):

IP Address (Manual or DHCP, In DHCP mode, if DHCP server is not available, then use manually set IP address)

Manual, 192.168.1.1

TCP/IP Settings (Router Mode):

1. WAN Settings 1. Static IP 2. DHCP Client 3. PPPoE

2. LAN Settings 1. DHCP Server

Time Setting 1. Current Time 2. Time Zone Select 3. Enable NTP client update

GMT Disabled

RADIUS Settings IP Address of Authentication RADIUS Server

0.0.0.0

Firewall Setting (Router Mode Only)

1. Src IP Filtering 2. Dest IP Filtering 3. Src Port Filtering 4. Dest Port Filtering 5. Port Forwarding 6. UDP Pass-through 7. DMZ

Wireless Basic Wireless Settings

Disable Wireless LAN Interface Unselected Operation Mode AP AP Mode Function: 1. SSID 2. Broadcast SSID 3. 802.11 Mode 4. HT Protect 5. Frequency/Channel 6. Extension Channe

Wireless Enabled 802.11a/n Disabled 5745MHz (149) None

Table 2-2 Firmware Specification (Fat AP Mode)


7. Channel Model 1. 5MHz 2. 10MHz 3. 20MHz 4. 40MHz

8. Maximum Output Power (per chain) 9. Date Rate 10. Extension channel protect mode

1. None 2. CTS to self 3. RTS-CTS

20MHz Full Auto None

Wireless Client Mode Function: 1. SSID 2. Lock AP MAC 3. 802.11 Mode 4. Channel Model

1. 5MHz 2. 10MHz 3. 20MHz 4. 40MHz

5. Maximum Output Power (per chain) 6. Extension channel protect mode


7. Enable MAC Clone

Wireless Disabled 802.11a/n 20MHz Full None Disabled

Bridge Mode Function: 1. 802.11 Mode 2. Frequency/Channel 3. Extension Channe 4. Channel Model

1. 5MHz 2. 10MHz 3. 20MHz 4. 40MHz

5. Maximum Output Power (per chain) 6. Data Rate 7. Extension channel protect mode


802.11a/n 5745MHz (149) None 20MHz Full Auto None

AP Repeater Mode Function: 1. SSID 2. Broadcast SSID 3. 802.11 Mode 4. HT Protect 5. Frequency/Channel 6. Extension Channe 7. Channel Model

1. 5MHz 2. 10MHz 3. 20MHz 4. 40MHz

8. Maximum Output Power (per chain)

Wireless Enable 802.11 a/n Disabled 5745MHz (149) None 20MHz Full


9. Date Rate 10. Extension channel protect mode


Auto None

Profile Settings 1. VAP Profile Settings (up to 16 profiles) 2. Enable 802.1Q VLAN

1. Management VLAN ID In Each Profile: Basic Settings 1. Profile Name 2. SSID 3. Broadcast SSID 4. Wireless Separation 5. WMM 6. Station Number Limitation 7. Max. Station Num Security Settings 1. Open System 2. Shared Key（64/128/152-bits WEP） 3. Lagacy 802.1X 4. WPA 5. WPA2 6. WPA + WPA2 7. WPA-PSK(TKIP) 8. WPA2-PSK(AES) 9. WPA-PSK + WPA2-PSK

Disabled 0 Profile1~16 Wireless Enabled Disabled Enabled Disabled 32 Open System

Advanced settings A-MPDU Aggregation Enabled A-MSDU Aggregation Disabled Short GI Enabled RTS Threshold(0~2347) 2347 Fragmentation Length(256~2346) 2346 Beacon Interval(20~10000ms) 100 DTIM Interval (1-255) 1 Preamble Type Auto IGMP Snooping Enabled RIFS Enabled Link Integration Disabled TDM Coordination Disabled Space-in-meter 1000 (m)

Access Control Support up to 32 MAC addresses for each profile with modes below:

1. Disable 2. Allow Listed 3. Deny Listed

Disabled

Traffic Shaping 1. Overall Traffic Shaping 1. Incoming Traffic Limit 2. Incoming Traffic Burst 3. Outgoing Traffic Limit 4. Outgoing Traffic Burst

Disabled


2. VAP Traffic Shaping (per VAP profile) 1. Outgoing Traffic Limit 2. Outgoing Traffic Burst

Disabled

Captive Portal Support CoovaChilli Access Controller (enable/disable per VAP profile) 1. RADIUS Settings

1. Primary RADIUS Server 2. Secondary RADIUS Server 3. RADIUS Auth Port 4. RADIUS Acct Port 5. RADIUS Shared Secret 6. RADIUS NASID

2. Captive Portal Settings 1. UAM Portal URL 2. UAM Secret

Disabled

WDS Setting WDS Separation Remote AP Address1~4

Disabled

Management Remote

Management

Embedded Web Configuration Interface 1. HTTP 2. HTTPS

HTTP

Remote Console Telnet

1. SSH

Telnet

SNMP Management V2

1. V3

V2

FTP Enabled WISE (Windows-based Utility Software) Disabled

Firmware Upload Upgrade Device’s Firmware Configuration File 1. Backup and Restore Configuration

2. Reset Settings to Factory Default 3. Reboot Device

Password Settings Change Password password Certificate Settings Import / Delete User’s Certificate Files for

Wireless Client Mode’s User Authentication (802.1X, WPA, or WPA2)

Tools System Logs Syslog (RFC 3164) Support Disabled Site Survey Wireless Network (AP) Scan Tool Ping Watchdog Enable Ping Watchdog

IP Address to Ping Ping Interval Startup Delay Failure Count To Reboot

Disabled 0.0.0.0 300 Seconds 100 Seconds 300

Data Rate Test

Perform Per-Datarate Transmission Test and Display Throughput Statistics (WDS Mode Only)

Antenna Alignment

Perform Continuous Throughput Statistics for Antenna Alignment (WDS Mode Only)

Speed Test Perform TCP/IP Data Throughput Test (All Mode)

Table 2-3 Firmware Specification (AC & Thin AP Mode) Function Catalog Detail Function Default settings


Web Language English English Status Information

Managed APs Wireless Users

Wireless Settings

Wireless Networks Wireless Network Name (SSID) Settings, up to 16 SSID profiles can be activated. In Each Profile: Basic Settings 1. SSID 2. Description 3. Broadcast SSID 4. Wireless Separation 5. WMM 6. Station Number Limitation 7. Max. Station Num Security Settings 1. Open System 2. Shared Key（64/128/152-bits WEP） 3. Lagacy 802.1X 4. WPA 5. WPA2 6. WPA + WPA2 7. WPA-PSK(TKIP) 8. WPA2-PSK(AES) 9. WPA-PSK + WPA2-PSK

Wireless Profile1 ~ 16 Enabled Disabled Enabled Disabled 32 Open System

Wireless Protocol Basic Settings 1. Country Region 2. 802.11 Mode 3. Data Rate Advanced Settings 1. A-MPDU Aggregation 2. A-MSDU Aggregation 3. Short GI 4. IGMP Snooping 5. RIFS 6. HTProtect 7. Preamble Type 8. RTS Threshold(0~2347) 9. Fragmentation Length(256~2346) 10. Beacon Interval(20~10000ms) 11. DTIM Interval (1-255) 12. Extension Channel Protection 13. Space In Meter 14. Link Integration 15. TDM Coordination

United States 802.11a/n Auto Enabled Disabled Enabled Enabled Enabled Disabled Auto 2347 2346 100 1 None 1000 (m) Disabled Disabled

Access Control Support up to 32 MAC addresses for each profile with modes below: 1. Disable 2. Allow Listed 3. Deny Listed

Disabled

Traffic Shaping 1. Overall Traffic Shaping Disabled


1. Incoming Traffic Limit 2. Incoming Traffic Burst 3. Outgoing Traffic Limit 4. Outgoing Traffic Burst

2. VAP Traffic Shaping (per VAP profile) 1. Outgoing Traffic Limit 2. Outgoing Traffic Burst

Disabled

Captive Portal Support CoovaChilli Access Controller (enable/disable per VAP profile) 1. RADIUS Settings

1. Primary RADIUS Server 2. Secondary RADIUS Server 3. RADIUS Auth Port 4. RADIUS Acct Port 5. RADIUS Shared Secret 6. RADIUS NASID

2. Captive Portal Settings 1. UAM Portal URL 2. UAM Secret

Disabled

RADIUS Settings IP Address of Authentication RADIUS Server

0.0.0.0

Firewall Setting (Router Mode Only)

1. Src IP Filtering 2. Dest IP Filtering 3. Src Port Filtering 4. Dest Port Filtering 5. Port Forwarding 6. UDP Pass-through 7. DMZ

Management AP Management Management of Individual Thin APs 1 Restart 2 Rename 3 Set IP 4 Radio

4.1 Channel Mode 4.2 Channel 4.3 Extension Channel 4.4 Output Power

5 Upgrade Selected 6 Upgrade All

20MHz 5745MHz (149) None Full

System Settings: 1. Device Settings 1. Device Mode 2. Device Name 3. Ethernet DateRate 4. Spanning Tree (STP) 5. STP Forward Delay

2. IP Address Settings 1. (AC) Device’s IP Address (Manual

or DHCP, In DHCP mode, if DHCP server is not available, then use manually set IP address)

2. DHCP Server for configuring IP Addresses of Thin APs

apXXXXXX Auto Enable 1 (second) Manual, 192.168.1.1 Disabled

Time Settings 1. Current Time 2. Time Zone Select

GMT


3. Enable NTP client update Disabled Firmware Upload Upgrade Device’s Firmware

1. AC Firmware 2. TAP Firmware

Configuration File 1. Backup and Restore Configuration 2. Reset Settings to Factory Default 3. Reboot Device

Password Settings Change Password password Syslog Settings 1. Syslog (RFC 3164) Support

2. E-Mail (SMTP) Support Disabled Disabled

System Log Display System Log System Alert Display System Alert

Tools Ping Perform ICMP ‘ping’ Test Trace Route Perform ‘traceroute’ Test


2.3 Power Adapter Specification

Output: 15V @ 0.8A (switching)

2.4 Physical specification

The Physical specifications of the product are as below:

Table 2-4 Physical Specification Items Description

Dimension 110.98*255.6*47.65mm Weight ≦500g Enclosure IP55

2.5 Environment specification

The Environment specifications of the product are as below:

Table 2-5 Environment Specification Items Device Description Power Adapter Spec

Operating Temperature(Max) -20° ~ +70°C 0° ~ +40°C

Operating Humidity (non-condensing) 10 to 95% RH 20 to 85% RH

Storage Temperature -40 ~ +70°C -20 ~ +60°C

Storage Humidity (non-condensing) 10 to 95% RH 5 to 95% RH

Warranty 12 Months

Green RoHs /Reach Compliant


2.6 Safety/Country Approval

We will do EMI/EMC pre-test according to the following items:

Table 2-6 Safety/Country Approval Items Description ID number

FCC Part15 sub B

Part15 sub C

CE EN300 328

EN301 489-1/17

EN60950

CCC For China

2.7 Packaging Specification

The following items will be required for the complete packaging of the ZN-7200-2AEI-O:

Table 2-7 Package Item Comments

Carton Suitable size to fit in

Gift Box / Cushion Suitable size to fit in

ZN-7200-2AEI-O Whole product should be in a protective bag

Power Supply Appropriate adapter based on the region

PoE injector Suitable size to fit in

Steel Cable Tie Suitable size to fit in


3 Pin Assignment Spec Item Description & Pin Assignment

(ETH)

RJ-45 PCB Jack 1Port

Pin NO. Signal Name Pin Definition

1 RX+ Receive(+)

2 RX- Receive(-)

3 TX+ Transmit(+)

4 15V + Power Supply

5 15V + Power Supply

6 TX- Transmit(-)

7 GND GND

8 GND GND

(RS232)

RS232 1PORT-4Pin


1 VCC 3.3V

2 GND GND

3 UART_SOUT UART_TX

4 UART_SIN UART_RX


(Reset)


1 AR9342_RES AR9342_RES

2 GND GND

3 FGND FGND

4 FGND FGND

ieee 802.11 a/n wireless cpe product...

Documents