ieee antennas and wireless propagation letters 1
TRANSCRIPT
IEEE ANTENNAS AND WIRELESS PROPAGATION LETTERS 1
Electromagnetic Modeling of Lossy Materials witha Potential-Based Boundary Element Method
Shashwat Sharma, Graduate Student Member, IEEE, and Piero Triverio, Senior Member, IEEE
AbstractâThe boundary element method (BEM) enables solv-ing three-dimensional electromagnetic problems using a two-dimensional surface mesh, making it appealing for applicationsranging from electrical interconnect analysis to the design ofmetasurfaces. The BEM typically involves the electric andmagnetic fields as unknown quantities. Formulations based onelectromagnetic potentials rather than fields have garnered in-terest recently, for two main reasons: (a) they are inherentlystable at low frequencies, unlike many field-based approaches,and (b) potentials provide a more direct interface to quantumphysical phenomena. Existing potential-based formulations forelectromagnetic scattering have been proposed primarily for per-fect conductors. We develop a potential-based BEM formulationwhich can capture both dielectric and conductive losses, andaccurately models the skin effect over broad ranges of frequency.The accuracy of the proposed formulation is validated throughcanonical and realistic numerical examples.
Index TermsâMaxwellâs equations, electromagnetic potentials,boundary element method, integral equations, lossy conductors.
I. INTRODUCTION
ELECTROMAGNETIC simulation tools based on theboundary element method (BEM) [1] have gained trac-
tion in a variety of applications, ranging from antenna model-ing [2] to high-speed interconnect analysis [3]â[7]. The BEMis based on a surface integral representation of Maxwellâsequations, which allows three-dimensional problems to besolved in terms of quantities defined on a two-dimensional sur-face mesh. Many conventional full-wave BEM formulations,which take electric and magnetic fields as unknown quantities,suffer from numerical instability at very low frequencies [8].The need to model multiscale structures at both high andlow frequencies arises in applications such as the analysisof integrated circuit components. This motivates the develop-ment of broadband BEM formulations where electromagneticpotentials, rather than fields, are taken as the unknowns [9],[10]. These formulations do not rely on the coupling betweenelectric and magnetic fields, and provide a natural interface toquantum phenomena, which is an important consideration inemerging applications such as quantum computing [11], [12].Potential-based methods may also be well-suited for coupledelectromagnetic-circuit simulations.
S. Sharma is with the Edward S. Rogers Sr. Department of Electrical& Computer Engineering, University of Toronto, Toronto, ON, M5S 3G4Canada, e-mail: [email protected]. P. Triverio is with the Ed-ward S. Rogers Sr. Department of Electrical & Computer Engineering andwith the Institute of Biomedical Engineering, University of Toronto, Toronto,ON, M5S 3G4 Canada, email: [email protected].
This work was supported by Advanced Micro Devices, by the Natural Sci-ences and Engineering Research Council of Canada (Collaborative Researchand Development Grants program), and by CMC Microsystems.
Manuscript received . . .; revised . . ..
Potential-based integral equation (PIE) methods for scat-tering analysis have been developed primarily for perfectconductors [9], [10], [13]â[15]. For low frequencies and sub-wavelength structures, where PIE formulations are most sorelyneeded, the skin depth in a conductor may be large comparedto its physical dimensions, and modeling the conductor asperfect may be inaccurate. Although magnetoquasistatic PIEformulations have been used for eddy current modeling inlossy conductors [16]â[20], these techniques do not apply inthe presence of dielectric inclusions, or at high frequencies.PIE-based modeling of lossless dielectric objects was consid-ered in [21], but mainly from a theoretical perspective, andin [22], but in the time domain. Also, the method in [21]involves a linear combination of integral equations writtenfor adjacent materials. As in the case of analogous field-based formulations [23]â[25], the formulation in [21] maybe inaccurate for large contrasts in material parameters ofadjacent media. To the best of our knowledge, a full-wavePIE formulation for lossy penetrable materials has not beendemonstrated in the frequency domain.
In this article, we devise a novel full-wave PIE formula-tion for electromagnetic scattering from lossy dielectrics andconductors, applicable at both low and high frequencies. Theproposed formulation couples the scalar and vector potentialintegral equations [9] in the regions internal and external toeach object. An appropriate discretization is discussed, and theaccuracy of the formulation is demonstrated numerically overwide ranges of conductivity and frequency.
II. PROPOSED FORMULATION
We consider time-harmonic scattering from an object oc-cupying volume V , with surface S and outward unit normalvector n. Symbols Sâ and S+ denote the internal and ex-ternal sides of S, respectively. The object has permittivity Îľ,permeability Âľ, and conductivity Ď > 0. The permittivity maybe complex, Îľ = ξⲠâ jÎľâ˛â˛, where the imaginary part representsdielectric losses [26]. The object resides in free space, V0, withpermittivity Îľ0 and permeability Âľ0.
A. Internal Region
For ~r â V , the magnetic vector and electric scalar poten-tials, ~A (~r) and Ď (~r), respectively, can be defined via [27]
Âľ ~H (~r) = âĂ ~A (~r), (1)~E (~r) = âjĎ ~A (~r)ââĎ (~r), (2)
where Ď is the angular frequency, ~H (~r) is the magneticfield, and ~E (~r) is the electric field. Using (1) and (2) in
arX
iv:2
108.
0276
4v2
[m
ath.
NA
] 1
2 D
ec 2
021
IEEE ANTENNAS AND WIRELESS PROPAGATION LETTERS 2
Maxwellâs equations, it can be shown that ~A (~r) satisfies thehomogeneous Helmholtz equation [27]
â2 ~A (~r) + k2 ~A (~r) = 0, (3)
when the Lorenz gauge
â ¡ ~A (~r) = âÂľ (jĎξⲠ+ ĎÎľâ˛â˛ + Ď) Ď (~r) (4)
is adopted [9], [28]. In (3), k2 = âjĎÂľ (jĎξⲠ+ ĎÎľâ˛â˛ + Ď)is the wave number associated with the objectâs material.Likewise, Ď (~r) satisfies the Helmholtz equation [27](
γ¾â1 + Ď) [â2Ď (~r) + k2Ď (~r)
]= 0, (5)
where Îł , (jĎξⲠ+ ĎÎľâ˛â˛ + Ď)Âľ. The use of Greenâs identi-ties [29] with (3) and (5) leads to the integral equations [9]
L[nⲠĂâⲠà ~A (~r â˛)
]+K
[nⲠà ~A (~r â˛)
]+ ~A (~r) + Îł L
[Ď (~r â˛)nâ˛
]ââL
[nⲠ¡ ~A (~r â˛)
]= 0, (6)
γ¾â1(L[nⲠ¡ âĎ (~r â˛)
]+M
[Ď (~r â˛)
]â Ď (~r)
)= 0, (7)
where primed and unprimed coordinates denote source andobservation points, respectively, ~r â V , and ~r Ⲡâ Sâ. Theintegral operators in (6) and (7) are defined as [1]
L[~a (~r â˛)
]=
ËSdS â˛G (k, ~r, ~r â˛)~a (~r â˛) , (8)
K[~a (~r â˛)
]=
ËSdS â˛âG (k, ~r, ~r â˛)Ă ~a (~r â˛) , (9)
M[a (~r â˛)
]=
ËSdS ⲠnⲠ¡ âG (k, ~r, ~r â˛) a (~r â˛) , (10)
where G (k, ~r, ~r â˛) is the Greenâs function associated with theobjectâs material,
G (k, ~r, ~r â˛) =eâjk|~râ~r â˛|4Ď |~r â ~r â˛| . (11)
Next, the objectâs surface is discretized with a triangu-lar mesh. Quantity nĂâĂ ~A (~r) is expanded with Rao-Wilton-Glisson (RWG) functions [30], ~fn (~r) normalizedby edge length, while nĂ ~A (~r) is expanded with Buffa-Christiansen functions [31], ~gn (~r), which are defined on abarycentric refinement of the mesh. This choice of functionsstems from (1) and (2), which indicate that n Ă âĂ ~A (~r)and nĂ ~A (~r) are related to n Ă ~H (~r) and n Ă ~E (~r) on S,respectively. Since n Ă ~H (~r) and n Ă ~E (~r) can be interpretedas electric and magnetic surface current densities, respec-tively, n Ă âĂ ~A (~r) and nĂ ~A (~r) must both be expandedwith divergence-conforming basis functions [32], while re-specting their mutual orthogonality [33]. These requirementsare satisfied by the proposed expansion scheme.
Unknowns Ď (~r) and n ¡ ~A (~r) are expanded with unit-amplitude pulse functions, hn (~r), while n¡âĎ (~r) is expandedwith area-normalized pulse functions, hn (~r). The choice ofnormalizing by area was based on an empirical study ofthe condition number of the final system matrix. A moresophisticated choice of basis function for Ď (~r), such as the onesuggested in [22], may lead to improved accuracy. However,
as shown in Section III, the pulse functions are sufficientlyaccurate in a variety of cases.
Taking the cross product of n with (6) and letting ~r â Sâgives its rotated tangential part, which is tested with nĂRWGfunctions to get the matrix relation
L(ff)ac, +
(K(fg) +
1
2I(fg)Ă
)at,
+ Îł L(fh)ÎŚ + DTL(hh)an, = 0. (12)
Taking the dot product of n with (6) and letting ~r â Sâ givesits normal component, which is tested with hn (~r) to obtain
L(hf)ac, + K(hg)at, + Îł L(hh)ÎŚ
â(â(M(hh)
)Tâ 1
2I(hh)â
)an, = 0, (13)
where the superscript âT â denotes the matrix transpose. Fi-nally, taking ~r â Sâ in (7) and testing it with hn (~r) yields
γ¾â1
[L(hh)Ψ +
(M(hh) â 1
2I(hh)â
)ÎŚ
]= 0. (14)
In (12), (13), and (14), L, K and M are the discretized L, Kand M operators, respectively, where a dash through a ma-trix indicates that the associated integral is computed in theprincipal value sense [1]. Term D is a sparse incidencematrix linking mesh edges and triangles [34]. Identity op-erator I
(fg)Ă is obtained by testing ~gn (~r) with n Ă ~fn (~r),
while I(hh)â involves testing hn (~r) with hn (~r). The super-
script labels (ij) on each discrete operator represent thetesting and basis functions involved, respectively. Column vec-tors ac,, at,, an,, ÎŚ and Ψ contain the unknown coefficientsassociated with nĂâĂ ~A (~r), nĂ ~A (~r), n ¡ ~A (~r), Ď (~r)and n ¡ âĎ (~r), respectively.
B. External RegionNext, PIEs are devised to capture the physics in the re-
gion external to S, following the procedure in Section II-Afor ~r, ~r Ⲡâ S+. However, instead of using the normal compo-nent of (6) for the external region, we take its divergence [13]and test the resulting equation with hn (~r). We found that thischoice leads to better conditioning of the final system matrix,and better accuracy. The resulting discrete equations are
L(ff)0 ac,0 +
(K
(fg)0 â 1
2I(fg)Ă
)at,0
+ Îł0 L(fh)0 ÎŚ0 + DTL
(hh)0 an,0 = âat,inc, (15)
L(hh)0 Dac,0 + Îł0
(M
(hh)0 +
1
2I(hh)â
)ÎŚ0
+ k20 L
(hh)0 an,0 = Îł0 ÎŚinc, (16)
L(hh)0 Ψ0 +
(M
(hh)0 +
1
2I(hh)â
)ÎŚ0 = âÎŚinc, (17)
where the subscript â0â on the matrix operators denotesthat the Greenâs function associated with V0 is used,and Îł0 , jĎÎľ0Âľ0. Subscript â0â on the column vectors ofunknowns indicates that the quantities are defined on S+.Subscript âincâ indicates incident potentials [9], [10].
IEEE ANTENNAS AND WIRELESS PROPAGATION LETTERS 3
C. Boundary Conditions
For nĂâĂ ~A (~r), nĂ ~A (~r) and Ď (~r), we use boundaryconditions on S identical to those in [9], [10],
Âľâ10 nĂâĂ ~A0 (~r) = Âľâ1 nĂâĂ ~A (~r), (18)
nĂ ~A0 (~r) = nĂ ~A (~r), (19)Ď0 (~r) = Ď (~r), (20)
where ~A (~r) and ~A0 (~r) are the magnetic vector potentialson Sâ and S+, respectively. For conductive objects, a newboundary condition is required for n ¡ ~A (~r) and n ¡ âĎ (~r),
â jĎ[Îł0Âľâ10 n ¡ ~A0 (~r)â γ¾â1n ¡ ~A (~r)
]â[Îł0Âľâ10 n ¡ âĎ0 (~r)â γ¾â1n ¡ âĎ (~r)
]= 0, (21)
which is used to eliminate n ¡ âĎ (~r) in (7). Equation (21)is derived using (2), (4) and the standard boundary condi-tions [28] for n ¡ ~E (~r), n ¡ ~E0 (~r) and n ¡ ~J (~r), where ~E (~r)and ~E0 (~r) are the electric fields in V and V0, respectively,and ~J (~r) is the conduction volume current density in V .
D. Final System Matrix
Equations (15), (12), (16), (13), (14) and (17) are con-catenated in that order, and the boundary condition (21) isapplied to get the final system of equations (22) at the topof the following page, where Ξ is the average mesh edgelength. In (22), the equations and unknowns have been strate-gically scaled to ensure stable direct factorization and goodaccuracy for wide ranges of frequency and conductivity. Itmay be necessary to enforce charge conservation at extremelylow frequencies. Although this point is not addressed in thepresent formulation, the results in Section III demonstrate theextremely wide ranges of frequency over which the proposedmethod still remains accurate. Also, the system matrix in (22)contains two vector quantities (ac,0, at,) and four scalarquantities (ÎŚ, an,, an,0 Ψ0) as unknowns, while most field-based formulations for lossy conductors contain only twovector and up to one scalar unknown quantity [3], [7], [35].However, the additional unknowns in the proposed methodmay be well worth the broadband performance, particularlywhen coupled with acceleration algorithms [36]â[39]. It maybe possible to obtain a smaller system matrix, but the scope ofthis work is to establish that potential-based formulations canbe used to model lossy conductors accurately and over verywide ranges of frequency and conductivity.
III. RESULTS
The accuracy of the proposed formulation is validatedthrough comparisons with analytical solutions and an exist-ing field-based BEM formulation: the enhanced augmentedelectric field integral equation (eAEFIE) for penetrable ob-jects [35], [40]. The numerical integration routines in [3] wereused for the operators associated with the internal region,to maintain accuracy for highly conductive media. Electricand magnetic fields tangential to S were obtained as a post-processing step via (1) and (2).
A. Sphere
First, we consider a sphere with diameter 1m and relativepermittivity 2, excited by a plane wave. The sphere is meshedwith 2, 114 triangles, and the bistatic radar cross section (RCS)is compared against the analytical Mie series (Fig. 1). The RCSis reported for the plane along which the incident electric fieldis polarized (E-plane). We consider conductivities spanning 10decades from 10â3 S/m, where the sphere behaves like adielectric, to 107 S/m, corresponding to a good conductor. Ninedecades of frequencies from 1Hz to 1GHz are simulated toencompass skin depths from 1 Âľm to several times the sphereâsdiameter. For the 1GHz cases, a finer mesh with 3, 786triangles was used. Fig. 1 demonstrates the excellent accuracyof the proposed formulation. The results deviate slightly fromthe Mie series in the bottom panel, but identical deviationsare observed for the eAEFIE formulation. Therefore, theseerrors can be attributed to the discretization and numericalintegration, which are common to both formulations.
B. Cube
Next, we consider an FR-4 cube meshed with 3, 274triangles, with side length 1m, ξⲠ= 4.4 Îľ0, and loss tan-gent tan δ = Îľâ˛â˛/ξⲠ= 0.03 [41]. A plane wave impinges on thecube with the electric field polarized as shown in the insetin the bottom panel of Fig. 2. The E-plane bistatic RCSfor the proposed formulation is compared with the resultsobtained via the eAEFIE, for frequencies between 10 kHzand 1GHz. The top panel of Fig. 2 demonstrates the excel-lent accuracy of the proposed formulation compared to theeAEFIE. We also considered the case when ξⲠ= Îľ0, Îľâ˛â˛ = 0,and Ď â
[10â3, 107
]S/m at 100MHz, corresponding to skin
depths between 1.6m and 16 Âľm. Excellent agreement with theeAEFIE was achieved, as shown in the bottom panel of Fig. 2.The inset shows the surface current density for Ď = 10S/m.
C. Split Ring Resonator Array
Finally, we consider a 2Ă 2 array of split ring resonators(SRRs), which are of relevance in the design of metamaterialsand metasurfaces [42]. Each element has a relative permittivityof 11 and an electrical conductivity of 107 S/m. The elementshave side length 2 Âľm, width 0.2 Âľm, and height 0.1 Âľm. Thewidth of the gap is 0.2 Âľm. The structure is meshed with 3, 392triangles, and excited with an incident plane wave travelingalong the âz direction, with the electric field polarized inthe y direction. The geometry is shown in Fig. 3. We considerthe frequencies 10GHz, 1THz and 100THz. Fig. 3 shows theelectric surface current density for the 100THz case. Fig. 4shows the magnitude of the electric field measured along theprobe line shown in Fig. 3. The probe line is placed alongthe x axis in the xz plane bisecting the array, 0.4 Âľm aboveit. Excellent agreement is obtained compared to the eAEFIEfor all three frequencies, demonstrating the accuracy of theproposed PIE formulation for realistic structures.
IV. CONCLUSION
A boundary element formulation based on the electric scalarand magnetic vector potential is proposed for the accurate
IEEE ANTENNAS AND WIRELESS PROPAGATION LETTERS 4
1ΞL
(ff)0 K
(fg)0 â 1
2I(fg)Ă
jk0Ξ
L(fh)0 0 1
ΞDTL
(hh)0 0
¾Ξ¾0
L(ff) K(fg) + 12I(fg)Ă
c0γΞ
L(fh) 1ΞDTL(hh) 0 0
L(hh)0 D 0 jk0
(M
(hh)0 + 1
2I(hh)
â
)0 k2
0 L(hh)0 0
¾¾0
L(hf) ΞK(hg) c0γ L(hh)(M(hh)
)T â 12I(hh)
â 0 0
0 0 M(hh) â 12I(hh)
âk2
Îłc0L(hh) â k20
Îłc0
¾¾0
L(hh) Îł0Îłc0
¾¾0
L(hh)
0 0 M(hh)0 â 1
2I(hh)
â 0 0 1c0
L(hh)0
ac,0
at,/Ξ
ÎŚ/c0
an,
an,0
Ψ0
=
âat,inc/Ξ
0
Îł0 ÎŚinc
0
0
âÎŚinc/c0
. (22)
0 25 50 75 100 125 150 175θ (degrees)
â350
â340
â330
â320
Bis
tati
cR
CS
(dB
sm)
f = 1 Hz
Ď â {10â3, 10â1,
101, 103} S/m
Ď â {10â3, 10â1,
101, 103} S/m
Ď â {10â3, 10â1,
101, 103} S/m
Ď = 107 S/mĎ = 107 S/mĎ = 107 S/m
Mie
eAEFIE
Proposed
0 25 50 75 100 125 150 175θ (degrees)
â240
â220
â200
Bis
tati
cR
CS
(dB
sm)
f = 1 kHz
Ď â {10â3, 10â1, 101} S/mĎ â {10â3, 10â1, 101} S/mĎ â {10â3, 10â1, 101} S/m
Ď = 103 S/mĎ = 103 S/mĎ = 103 S/m
Ď = 107 S/mĎ = 107 S/mĎ = 107 S/m
Mie
eAEFIE
Proposed
0 25 50 75 100 125 150 175θ (degrees)
â140
â120
â100
â80
Bis
tati
cR
CS
(dB
sm)
f = 1 MHz
Ď â {10â3, 10â1} S/mĎ â {10â3, 10â1} S/mĎ â {10â3, 10â1} S/m
Ď = 101 S/mĎ = 101 S/mĎ = 101 S/m
Ď = 103 S/mĎ = 103 S/mĎ = 103 S/m
Ď = 107 S/mĎ = 107 S/mĎ = 107 S/m
Mie
eAEFIE
Proposed
0 25 50 75 100 125 150 175θ (degrees)
â30
â20
â10
0
10
20
Bis
tati
cR
CS
(dB
sm)
f = 1 GHzĎ = 10â3 S/mĎ = 10â3 S/mĎ = 10â3 S/m
Ď = 10â1 S/mĎ = 10â1 S/mĎ = 10â1 S/m
Ď = 101 S/mĎ = 101 S/mĎ = 101 S/m Ď â {103, 107} S/mĎ â {103, 107} S/mĎ â {103, 107} S/m
Mie
eAEFIE
Proposed
Fig. 1: Accuracy validation for the sphere in Section III-A.The same horizontal axis applies to all panels.
modeling of lossy objects over wide ranges of frequencyand conductivity. Unlike existing potential-based scatteringformulations, the proposed method accurately captures the skineffect both at low and high frequencies, and can model bothgood conductors and lossy dielectrics. The accuracy of the pro-posed formulation is validated through canonical and realisticnumerical examples, and excellent agreement with analyticalresults and an existing field-based method is observed for atleast nine decades of frequency and conductivity.
0 25 50 75 100 125 150 175θ (degrees)
â200
â150
â100
â50
0
Bis
tati
cR
CS
(dB
sm)
tan δ = 0.03
f = 10 kHzf = 10 kHz
f = 1 MHzf = 1 MHz
f = 10 MHzf = 10 MHz
f = 100 MHzf = 100 MHz
f = 1 GHzf = 1 GHz
eAEFIE
Proposed
0 25 50 75 100 125 150 175Âľ (degrees)
°40
°20
0
Bis
tatic
RC
S(d
Bsm
)
f = 100 MHz
Ì = 10°3 S/mÌ = 10°3 S/m
Ì = 10°1 S/mÌ = 10°1 S/m
ĂŚ = 101 S/mĂŚ = 101 S/m
ĂŚ 2 {103, 107} S/mĂŚ 2 {103, 107} S/m
eAEFIE
Proposed
Eâ
Hâ
Propagationdirection
Fig. 2: Accuracy validation for the cube in Section III-B.
Probe line
0.4 Âľm
Fig. 3: Geometry and electric surface current density magni-tude for the SRR array in Section III-C.
0 50 100 150 200 250Distance along probe line (Âľm)
10â1
100
101
|~ E|(
V/m
) f = 10 GHzf = 10 GHz
f = 1 THzf = 1 THz
f = 100 THzf = 100 THz
eAEFIE
Proposed
Fig. 4: Near-field | ~E (~r)| for the SRR array in Section III-C.
IEEE ANTENNAS AND WIRELESS PROPAGATION LETTERS 5
REFERENCES
[1] W. C. Chew, Waves and Fields in Inhomogeneous Media. Hoboken,NJ, USA: Wiley, 1999.
[2] P. Yla-Oijala, M. Taskinen, and J. Sarvas, âSurface integral equationmethod for general composite metallic and dielectric structures withjunctions,â Prog. Electromagn. Res., vol. 52, pp. 81â108, 2005.
[3] Z. G. Qian, W. C. Chew, and R. Suaya, âGeneralized impedanceboundary condition for conductor modeling in surface integral equation,âIEEE Trans. Microw. Theory Tech., vol. 55, no. 11, pp. 2354â2364, Nov.2007.
[4] W. Chai and D. Jiao, âDirect matrix solution of linear complexity forsurface integral-equation-based impedance extraction of complicated 3-D structures,â Proc. IEEE, vol. 101, no. 2, pp. 372â388, Jun. 2013.
[5] M. Huynen, K. Y. Kapusuz, X. Sun, G. Van der Plas, E. Beyne,D. De Zutter, and D. Vande Ginste, âEntire domain basis functionexpansion of the differential surface admittance for efficient broadbandcharacterization of lossy interconnects,â IEEE Trans. Microw. TheoryTech., vol. 68, no. 4, pp. 1217â1233, Jan. 2020.
[6] S. Sharma and P. Triverio, âAn accelerated surface integral equationmethod for the electromagnetic modeling of dielectric and lossy objectsof arbitrary conductivity,â IEEE Trans. Antennas Propag., vol. 69, no. 9,pp. 5822â5836, Sep. 2021.
[7] ââ, âSLIM: A well-conditioned single-source boundary elementmethod for modeling lossy conductors in layered media,â IEEE AntennasWireless Propag. Lett., vol. 19, no. 12, pp. 2072â2076, Sep. 2020.
[8] Z. G. Qian and W. C. Chew, âA quantitative study on the low frequencybreakdown of EFIE,â Microw. Opt. Technol. Lett., vol. 50, no. 5, pp.1159â1162, 2008.
[9] W. C. Chew, âVector potential electromagnetics with generalized gaugefor inhomogeneous media: Formulation,â Prog. Electromagn. Res., vol.149, pp. 69â84, Sep. 2014.
[10] F. Vico, M. Ferrando, L. Greengard, and Z. Gimbutas, âThe decoupledpotential integral equation for time-harmonic electromagnetic scatter-ing,â Commun. Pure Appl. Math., vol. 69, no. 4, pp. 771â812, 2016.
[11] W. C. Chew, A. Y. Liu, C. Salazar-Lazaro, and W. E. I. Sha, âQuantumelectromagnetics: A new look â part I,â IEEE J. Multiscale Multiphys.Comput. Tech., vol. 1, pp. 73â84, Oct. 2016.
[12] ââ, âQuantum electromagnetics: A new look â part II,â IEEE J.Multiscale Multiphys. Comput. Tech., vol. 1, pp. 85â97, Oct. 2016.
[13] Q. S. Liu, S. Sun, and W. C. Chew, âA potential-based integralequation method for low-frequency electromagnetic problems,â IEEETrans. Antennas Propag., vol. 66, no. 3, pp. 1413â1426, Mar. 2018.
[14] U. M. Gur and O. Ergul, âAccuracy of sources and near-zone fields whenusing potential integral equations at low frequencies,â IEEE AntennasWireless Propag. Lett., vol. 16, pp. 2783â2786, Aug. 2017.
[15] T. E. Roth and W. C. Chew, âDevelopment of stable A-ÎŚ time-domainintegral equations for multiscale electromagnetics,â IEEE J. MultiscaleMultiphys. Comput. Tech., vol. 3, pp. 255â265, Dec. 2018.
[16] C. Emson and J. Simkin, âAn optimal method for 3-D eddy currents,âIEEE Trans. Magn., vol. 19, no. 6, pp. 2450â2452, Nov. 1983.
[17] T. Morisue and M. Fukumi, â3-D eddy current calculations using themagnetic vector potential,â IEEE Trans. Magn., vol. 24, no. 1, pp. 106â109, Jan. 1988.
[18] T. Morisue, âA new formulation of the magnetic vector potential methodin 3-D multiply connected regions,â IEEE Trans. Magn., vol. 24, no. 1,pp. 110â113, Jan. 1988.
[19] H. Tsuboi and M. Tanaka, âThree-dimensional eddy current analysisby the boundary element method using vector potential,â IEEE Trans.Magn., vol. 26, no. 2, pp. 454â457, Mar. 1990.
[20] C. Bryant, C. Emson, and C. Trowbridge, âA general purpose 3Dformulation for eddy currents using the Lorentz gauge,â IEEE Trans.Magn., vol. 26, no. 5, pp. 2373â2375, Sep. 1990.
[21] J. Li, X. Fu, and B. Shanker, âDecoupled potential integral equationsfor electromagnetic scattering from dielectric objects,â IEEE Trans.Antennas Propag., vol. 67, no. 3, pp. 1729â1739, Mar. 2019.
[22] T. E. Roth and W. C. Chew, âLorenz gauge potential-based time domainintegral equations for analyzing subwavelength penetrable regions,âIEEE J. Multiscale Multiphys. Comput. Tech., vol. 6, pp. 24â34, Feb.2021.
[23] A. Poggio and E. Miller, âIntegral equation solutions of three-dimensional scattering problems,â in Computer Techniques for Elec-tromagnetics, ser. International Series of Monographs in ElectricalEngineering. Pergamon, 1973, pp. 159 â 264.
[24] Y. Chang and R. Harrington, âA surface formulation for characteristicmodes of material bodies,â IEEE Trans. Antennas Propag., vol. 25, no. 6,pp. 789â795, Nov. 1977.
[25] T. Wu and L. L. Tsai, âScattering from arbitrarily-shaped lossy dielectricbodies of revolution,â Radio Sci., vol. 12, no. 5, pp. 709â718, Sep. 1977.
[26] D. M. Pozar, Microwave Engineering, 4th ed. Hoboken, NJ, USA:Wiley, 2012.
[27] J. D. Jackson, Classical Electrodynamics, 3rd ed. Hoboken, NJ, USA:Wiley, 1999.
[28] E. J. Rothwell and M. J. Cloud, Electromagnetics, 3rd ed. Boca Raton,FL, USA: CRC Press, 2018.
[29] G. W. Hanson and A. B. Yakovlev, Operator Theory for Electromagnet-ics. New York, NY, USA: Springer-Verlag, 2002.
[30] S. Rao, D. Wilton, and A. Glisson, âElectromagnetic scattering bysurfaces of arbitrary shape,â IEEE Trans. Antennas Propag., vol. 30,no. 3, pp. 409â418, May 1982.
[31] A. Buffa and S. H. Christiansen, âA dual finite element complex on thebarycentric refinement,â Math. Computation, vol. 76, pp. 1743â1769,2007.
[32] W. Chew, M. Tong, and B. Hu, Integral Equation Methods for Elec-tromagnetic and Elastic Waves. San Rafael, CA, USA: Morgan &Claypool, 2008.
[33] F. P. Andriulli, K. Cools, H. Bagci, F. Olyslager, A. Buffa, S. Chris-tiansen, and E. Michielssen, âA multiplicative Calderon preconditionerfor the electric field integral equation,â IEEE Trans. Antennas Propag.,vol. 56, no. 8, pp. 2398â2412, Aug. 2008.
[34] Z.-G. Qian and W. C. Chew, âFast full-wave surface integral equa-tion solver for multiscale structure modeling,â IEEE Trans. AntennasPropag., vol. 57, no. 11, pp. 3594â3601, Nov. 2009.
[35] T. Xia, H. Gan, M. Wei, W. C. Chew, H. Braunisch, Z. Qian, K. Aygun,and A. Aydiner, âAn integral equation modeling of lossy conductors withthe enhanced augmented electric field integral equation,â IEEE Trans.Antennas Propag., vol. 65, no. 8, pp. 4181â4190, Aug. 2017.
[36] J. Song, C.-C. Lu, and W. C. Chew, âMultilevel fast multipole algorithmfor electromagnetic scattering by large complex objects,â IEEE Trans.Antennas Propag., vol. 45, no. 10, pp. 1488â1493, Oct. 1997.
[37] E. Bleszynski, M. Bleszynski, and T. Jaroszewicz, âAIM: Adaptiveintegral method for solving large-scale electromagnetic scattering andradiation problems,â Radio Sci., vol. 31, no. 5, pp. 1225â1251, Sep.1996.
[38] Z. Zhu, B. Song, and J. K. White, âAlgorithms in FastImp: a fastand wide-band impedance extraction program for complicated 3-Dgeometries,â IEEE Trans. Comput.-Aided Design Integr. Circuits Syst.,vol. 24, no. 7, pp. 981â998, Jul. 2005.
[39] S. Sharma and P. Triverio, âAIMx: An extended adaptive integral methodfor the fast electromagnetic modeling of complex structures,â IEEETrans. Antennas Propag., 2021 (early access).
[40] T. Xia, H. Gan, M. Wei, W. C. Chew, H. Braunisch, Z. Qian, K. Aygun,and A. Aydiner, âAn enhanced augmented electric-field integral equationformulation for dielectric objects,â IEEE Trans. Antennas Propag.,vol. 64, no. 6, pp. 2339â2347, Jun. 2016.
[41] A. Djordjevic, R. Biljie, V. Likar-Smiljanic, and T. Sarkar, âWidebandfrequency-domain characterization of FR-4 and time-domain causality,âIEEE Trans. Electromagn. Compat., vol. 43, no. 4, pp. 662â667, 2001.
[42] D. Guney, T. Koschny, and C. M. Soukoulis, âReducing ohmic losses inmetamaterials by geometric tailoring,â Phys. Rev. B, vol. 80, p. 125129,Sep. 2009.