Lighting Controls

1

Projection Screen

1

Audio/Visual Panels

1

Using a Laptop Computer

2-3

Using a Desktop Computer

4-5

Using a DVD-CD

Player

6-

8

Using a VCR

9-10

INSTRUCTION INDEX Page

If you need immediate assistance or further instructions, please contact The Center for Instructional Services at

extension 7121. To report a problem please visit our website at www.cis.tcu.edu

and click on the “Report A Problem”

link.

More information, including a printable version of these instructions, is available at our website.

08/07; P1eP, Preface

Audio Visual Panels

Desktop Interface Panel

A/C Power Outlets

Control Panel

Network Connections

Lighting Control Panel

To lower the screen press the ROOM

button once

To raise the screen press the ROOM

button once

1

-

ALL Lights ON

2

-

2/3 Lights ON

3 -

1/3 Lights ON

4

-

Instructors Area ONLY

OFF

–

ALL Lights OFF

Lighting Controls Projection Screen

08/07; P1eP, Page 1

Laptop

Cables

To Use a Laptop Computer

1. Push and hold (for approximately 3 seconds) the POWER button to turn on the projector.

2. Push the ROOM

button to lower the screen.

3. Press the INPUT3 button.

4a. Connect the VGA cable

to the video port on the back of the laptop.

4b. If needed, connect the audio cable

to theheadphone jack on the computer.

4c. If connecting to the TCU network or internet connect the CAT-5cable to the network connection on the computer.

NOTE: The computer must be registered with TCU’s Information Services.

5. Press button 3

to set the lights to the preset level.

6. Turn ON

the computer and proceed through your normal ‘boot up’

process.CAUTION: Turning the computer on before this step may result in

the image not being projected

7.

Access and

run

the desired program on the computer.

08/07; P1eP, Page 2

To Use a Laptop

Computer (continued)

12. Push the ROOM

button to raise the screen.

13. Press button 1

to set the lights to the preset level.

8. Adjust sound by slowly

turning the volume knob until you reach the desired volume.

9. When finished, exit the computer program and turn the computer off.

10. Disconnect any cables attached to the laptop.

11. Push and hold (for approximately 3 seconds) the POWER button to turn off the projector.

08/07; P1eP, Page 3

To Use a Desktop

Computer

1. Push and hold (for approximately 3 seconds) the POWER buttonto turn on the projector.

2. Push the ROOM

button to lower the screen.

3. Press the PC2 button.

08/07; P1eP, Page 4

4. If necessary, press the power

button to turn on the computer.

5b. If necessary, insert USB thumb drive into USB port.

5a. If necessary, press the open/close button to eject the CD/DVD try. Insert the CD or DVD into CD drive label side up. Press the open/close button to close the CD/DVD tray.

6. Mouse and keyboard are located in the drawer in the podium.

7a. Proceed through your normal “log in”

sequence.

7b. Guests of TCU will need to have the professor

“log in”

to the professors TCU account for access to the desktop.

To Use a Desktop

Computer (Continued)

12. Push the ROOM

button to raise the screen.

13. Press button 1

to set the lights to the preset level.

9. Adjust sound by slowly

turning the volume knob until you reach the desired volume.

10. When finished, exit the computer program, retrieve your CD, DVD, or USB thumb drive and log off.

11. Push and hold (for approximately 3 seconds) the POWER button to turn off the projector.

8. Access

and run

the desired program on the computer.

08/07; P1eP, Page 5

To Use the DVD / CD Player

1. Push and hold (for approximately 3 seconds) the POWER button to turn on the projector.

2. Push the ROOM

button to lower the screen.

3. Press the VID1 button.

4. Press POWER

to turn unit on.

5. Press the OPEN

button to eject the tray.

6. Place DVD or CD into the traylabel side up.

POWER PLAY Skip Ahead / Skip BackPAUSESTOPDisc Tray OPEN /

CLOSE Tray

08/07; P1eP, Page 6

To Use the DVD / CD Player (Continued)

8. Press PLAY

on the DVD.

10. When finished, press STOP.

11. Press OPEN

to eject the tray and remove the DVD/CD.

12. Press OPEN

to CLOSE the tray.

08/07; P1eP, Page 7

9. Adjust sound by slowly

turning the volume knob until you reach the desired volume.

7. Press button 3

to set the lights to the preset level.

To Use the DVD / CD Player (Continued)

15. Press button 1

to set the lights to the preset level.

08/07; P1eP, Page 8

14. Push the ROOM button to raise the screen.

13. Push and hold (for approximately 3 seconds) the POWER button to turn off the projector.

To Use the VCR

1. Push and hold (for approximately 3 seconds) the POWER button to turn on the projector.

2. Push the ROOM

button to lower the screen.

3. Press the VID2 button.

6. Press button 3

to set the lights to the preset level.

4. Press POWER

to turn unit on.

5. Insert the tape into the VCR.

POWER PLAY Fast Forward / Reverse

PAUSE STOP / EJECTTape Tray Real Time Counter

08/07; P1eP, Page 9

To Use the VCR (Continued)

8. When finished, press STOP / EJECT.

9. Press STOP / EJECT to eject the tape.

11. Push the ROOM

button to raise the screen.

12. Press button 1

to set the lights to the preset level.

10. Push and hold (for approximately 3 seconds) the POWER button to turn off the projector.

08/07; P1eP, Page 10

7. Adjust sound by slowly

turning the volume knob until you reach the desired volume.