hand and finger orthoses

INDICATIONS FOR USE

IFO10Painful processes caused by direct trauma, injury or rupture of the

extensor, after surgical repair.

IFO20

IFO20B

IFO30

IFO40

Painful processes caused by direct trauma to the distal phalange

of the fingers.

IFO50Stops or reduces the flexion non-physiological and chronic of the

interphalangeal joints, Dupuytren disease.

TMC100

TMC150

Painful stadiums of trapezio-metacarpal joint caused by inflammation,

trauma, post-surgery. Retards the deviations by rheumatic deformities.

DQ100

DQ150

Treatments that require immobilization of these joints in painful and

inflammatory processes, such as stenosing tenosynovitis of the thumb

abductors or de Quervain’s disease.

MN100

Hemiplegia, wrist and finger spasticity, rheumatoid arthritis, post-surgical

that requires wrist neutral position, anti-sores in burnt, bedridden for long

periods, rehabilitation of the extension of the metacarpophalangeal and

interphalangeal joints.

MN200

Hemiplegia, acute rheumatoid arthritis, pain relief and aligns the joints,

post-surgical minimizing functional loss of mobility, anti-sores in burnt,

bedridden for long periods. Prevents the ulnar and radial deviation.

MN500Injuries to the wrist-joint without fracture, injuries of the distal radius,

synovitis post-surgical and synovial cysts.

MN600Treatment of the hand affected by radial nerve palsy and rehabilitation of

traumatic hand or after surgery.

hand a

nd fin

ger orthose

s

Hand and inger orthoses: functionally designed to treat each pathology

Its easily adaptable design and its manufacturing made of

lightweight materials improve the wearing comfort of the patient

• Dorsal valve with Thomas fitting top, to extent metacarpophalangeal and interphalangeal joints, with medial piece for thumb abduction.

• The elastic regulates the active tension necessary for the patient.

MN600 Ortec thomas splint [050056]

MN600

• Splints made of low density polyethylene for a perfect fitting.

• Removable fastening tapes, better adaptation and more comfort for the patient.

TMC150 BeigeTMC150TMC100

• Anatomical splint to unload the trapeziometacarpal joint with the thumb in functional position.

• TMC100: Made of light thermoplastic with gray velur tape.

• TMC150: Made of thermoplastic lined with pleasant gray velur tape or beige elastic adaptable.

TMC100 Ortec trapezio-metacarpal immobilizer [050029]

TMC150 Ortec trapeziometacarpal immobilizor splint lined [050030]

SIZES Wrist circumference

S <17 M 17-19 L >19

DQ150 BeigeDQ150DQ100

• Anatomical splint maintains the thumb in a functional position with immobilization of the trapeziometacarpal joint, while immobilizes the wrist joint.

• DQ100: In light thermoplastic, closed with pleasant gray velur tape.

• DQ150: In lined thermoplastic, closed with pleasant velur tape.

DQ100 Ortec De Quervain splint [050031]

DQ150 Ortec De Quervain splint lined [050032]

SIZES Wrist circumference/ Length in cm

S <17 Y 19 M 17-19 Y 21 L >19 Y 23

• Immobilizes the distal and proximal interphalangeal joints in extension. With shaped proximal support.

IFO10

IF010 Ortec interphalangeal immobilizer [050005]

SIZES finger Length meAsureD BY the PALmAr fAce in cm.

1 6.3 2 6.8 3 7.1 4 7.5 5 8.5

6 9.5 7 10 8 10.3 9 10.8

IFO40

• Malleable aluminum padded splint.

• Immobilizes the distal interphalangeal joints and stabilizes the proximal joints in functional approach.

IF040 Ortec immobilizing IFD rana federica [050001]

SIZES mAximAL finger Length

S 6.3 M 7.1 L 7.7

• Avoids the functional disability and limitation of extension of the fingers.

• A screw allows micrometric adjustment of the pressure to the extension of the joint.

IF050 Ortec finger progressive splint [050010]

IFO50

IFO20, IFO20B, IFO30

IF020 Ortec injected Stack splint [050002]

IF020B Ortec injected Stack splint. 10 units [050003]

IF030 Ortec molded Stack splint [50000]

• Immobilizes the distal interphalangeal joints in slight hyperextension, releasing the proximal ones.

• IFO20: The material, injected polypropylene, can be formed with warm water at 60 º. Includes mounting ribbon.

• IFO20B: The material ,injected polypropylene, can be shaped with warm water at 60 º. Bags of 10 pcs. That have the same size without mounting tape.

• IFO30: The material, formed polyethylene, can be mold with hot dry air by hand. Includes mounting ribbon.

SIZES

1 2 3 4 5 6 7 8

MN100

• Anatomical design that keeps the whole hand-wrist-finger in extension position with wrist joint in neutral position.

MN100 Ortec flat hand postural splint [050061]

S 6-7 M 7-8.5 L 8.5-10

SIZES PALmAr WiDth in cm

S 6-7 M 7-8.5 L 8.5-10

SIZES PALmAr WiDth in cm

MN500

• Anatomical design for the immobilization of the wrist, with palmar highlight reinforcement.

• Accommodation for thumb and dorsal opening with tongue.

MN500 Ortec polyethylene wrist immobilizer [052006]

SIZES Wrist circumference in cm.

S 14 -19 M 17-20 L 20-23

SIZES

S M L

MN200

• Anatomical design that keeps hand and wrist in a functional position.

MN200 Ortec functional hand postural splint [050060]

únicaTALLA

L R L R

L R

L R L R L R

L R

L R L R

L R

hand a

nd fin

ger orthose

s