inlet valves - geberit.com.authe geberit impuls380 cistern inlet valve art. no. 222.026.00.1 with...

IMPULS380 FORS

WL

CL

INLETVALVES

GeberitInlet Valves

1

112

30

243212

48

G 1/2”

49

170.360.00.1 Diaphragm and lever

IMPULS380 INLET VALVE 1/2”Art. No. 222.012.00.1

The Geberit Impuls380 cistern inlet valve Art. No. 222.012.00.1 with 1/2” nipple is used in some Geberit cisterns or as a general 1/2” inlet valve. The Impuls380 cistern inlet valve has an operating pressure range from 10 to 1000 kPa (0.1 to 10 bar). The valve is designed for fast and quiet filling action.

Service and spare partsGeberit Impuls380 cistern inlet valve is maintenance friendly. In the event of a blockage, the silicone diaphragm and lever part can be easily removed without tools for cleaning. The spare part is supplied as a kit (diaphragm, insert, cover and lever) in one package.

GeberitInlet Valves

2

FORS INLET VALVEFOR BOTTOM CONNECTION1/2” Art. No. 222.100.00.13/8” Art. No. 222.101.00.1

The Geberit Fors cistern inlet valve can be used world wide thanks to different connection versions and because of the large pressure range in which the filling valve operates: 10-1000 kPa (0.1 to 10 bar). All parts exposed to pressure are entirely made from PBT, a chlorine and acid resistant material.

Service and spare partsGeberit Fors cistern inlet valve is maintenance friendly. In the event of a blockage, the silicone diaphragm and lever part can be easily removed without tools for cleaning. The spare part is supplied as a kit (diaphragm, insert, cover and lever) in one package. After any maintenance or replacement of the valve, make sure that the fill and spill level of the cistern is correctly adjusted.

ART. NO. 222.101.00.1ART. NO. 222.100.00.1

CL

WL

25

9296

71

CL

WL

G 1/2”

CL

WL

G 3/8”

Min. 235 max. 385

41.5min.9 / max.15

min. 146 max. 296

Waterline

WL

CL


GeberitInlet Valves

3


274.400.00.1 Inlet valve clip


The Geberit Impuls380 inlet valve Art. No. 222.011.00.1 with short 3/8” nipple is used in many imported toilet suites. The Impuls380 cistern inlet valve has an operating pressure range from 10 to 1000 kPa (0.1 to 10 bar). The valve is designed for fast and quiet filling action.Importante note: When the complete inlet valve is replaced make sure that the fill and spill level of the cistern is correctly adjusted. If the old Servo valve was clipped to the overflow pipe of the Geberit outlet valve, the existing clip has to be replaced with a new clip Art. No. 274.400.00.1.

49

112

30

243212

29

G 3/8”

Service and spare partsGeberit Impuls380 cistern inlet valve is maintenance friendly. In the event of a blockage, the silicone diaphragm and lever part can be easily removed without tools for cleaning. The spare part is supplied as a kit (diaphragm, insert, cover and lever) in one package.

GeberitInlet Valves

4



The Geberit Impuls380 cistern inlet valve Art. No. 222.026.00.1 with long 3/8” stratos nipple is used in a number of cisterns from Caroma and Villeroy & Boch. The Impuls380 cistern inlet valve has an operating pressure range from 10 to 1000 kPa (0.1 to 10 bar). The valve is designed for fast and quiet filling action.Important note: When the complete inlet valve is replaced make sure that the fill and spill level of the cistern is correctly adjusted.

Service and spare partsGeberit Impuls380 cistern inlet valve is maintenance friendly. In the event of a blockage, the silicone diaphragm and lever part can be easily removed without tools for cleaning. The spare part is supplied as a kit (diaphragm, insert, cover and lever) in one package. After any maintenance or replacement of the valve, make sure that the fill and spill level of the cistern is correctly adjusted.

212 243

112

30

46

50

49

G 3/8”

GeberitInlet Valves

5

IMPULS380REAR-ENTRY INLET VALVEArt. No. 222.013.00.1

The Geberit Impuls380 cistern rear-entry inlet valve Art. No. 222.013.00.1 with 300mm long hose and 3/8” female connection is manufactured for use with the Geberit outlet valve. It fastens onto the overflow pipe of the outlet valve via a clip Art. No. 274.400.00.1 (clip has to be ordered separately). Impuls380 rear-entry Art. No. 222.013.00.1 can also be used with the Geberit UP170 concealed cistern. The Impuls380 inlet valve has an operating pressure range from 10 to 1000 kPa (0.1 to 10 bar). The valve is designed for fast and quiet filling action.

Service and spare partsThe Geberit Impuls380 cistern inlet valve is maintenance friendly. In the event of a blockage, the silicone diaphragm and lever part can be easily removed without tools for cleaning. The spare part is supplied as a kit (diaphragm, insert, cover and lever) in one package. The rear-entry hose is also available as a spare part. After any maintenance or replacement of the valve, make sure that the fill and spill level of the cistern is correctly adjusted.

G 3/8”


240.989.00.1 Rear-entry hose with 3/8” female nut (l = 300mm)


GeberitInlet Valves

6

Two different length and shape nipples.

Most Geberit Servo valves have a blue cap. Other parts are white and grey. The Geberit name and Watermark is also on this cap.

B) Long nipple Lb = 50 mm

A) Short nipple La = 33 mm

Close stop valve and remove old Servo valve Install new inlet valve and open stop valve Note: Unifill inlet valve works from low pressure (10kPa) to high pressure (1000kPa)

B) Install O-ring as shown

A) Align insert and push into opening

1 2 3

Lubricate all rubber rings

IMPULS380SERVO VALVE REPLACEMENT SETArt. No. 222.018.00.1

There were two models of the Geberit Servo filling valves with different length nipples sold in Australia. Referred to below as A & B. Model A was extensively used in imported toilet suites such as Villeroy & Boch, Duravit etc. Model B mainly in Caroma Suites. The Servo valve and spare parts are no longer available. A replacement set including Impuls380 cistern inlet valve and adaptor is available.

WARNING: Upon replacement of filling valve, the installer must ensure the cistern fill and spill level is correctly adjusted!

A

L a

Lb

B

Lubricant

AccessoriesIf the old servo valve was clipped to the overflow pipe of the Geberit outlet valve, the existing clip has to be replaced with a new clip Art. No. 274.400.00.1.


GeberitInlet Valves

7

Close stop valve (1) & remove valve (2).

Remove diaphragm cover.

Assemble diaphragm insert and cover Note: This membrane assembly is only suitable for Impuls380 inlet valves.

Click spindle into lever.

Unclip spindle from lever.

Wash diaphragm and cover with clean water.

Insert assembly into housing.

Re-install inlet valve. Open stop valve.

Undo diaphragm cover (1/4 turn).

Align diaphragm with insert.

Lock assembly into housing 1/4 turn.

Check and adjust the filling level.

WARNING! Upon maintenance or replacement of filling valve, the installer must ensure the cistern fill and spill level is correctly adjusted and complies with AS 1172.2 and AS/NZS 3500.1.

IMPULS380 SERVICE

1

2

1

2

1

2

1

2

1

2

1

21

2

1

2

1

21

2

1

2

1

2

GeberitInlet Valves

8

Note: This membrane assembly is only suitable for Fors bottom Inlet valve!Ensure diaphragm is aligned with insert.

Close stop valve.

Wash diaphragm with clean water.

Lock assembly into housing.

Re-insert into valve.

Unclip diaphragm cover (1/4 turn).

Remove water connector, check filter.

Note: Fors is also fitted with a filter which might need cleaning.

Remove diaphragm cover.

Assemble diaphragm insert and cover.

Wash filter.

Check and adjust the filling level.

WARNING! Upon maintenance or replacement of filling valve, the installer must ensure the cistern fill and spill level is correctly adjusted and complies with AS 1172.2 and AS/NZS 3500.1.

WL

CL

W L

CL

WL

CL

W L

CL

WL

CL

W L

CL

WL

CL

W L

CL

WL

CL

W L

CL

WL

CL

W L

CL

WL

CL

W L

CL

WL

CL

W L

CL

WL

CL

W L

CL

WL

CL

W L

CL

FORS SERVICE

Open stop valve.

GeberitInlet Valves

9

NOTES

Geberit Pty LtdUnit 8a 6-8 Byfield Street Macquarie ParkNSW 2113

Phone: 1800 GEBERIT +61 2 9889 7866Fax: +61 2 9889 7855

[email protected]

www.geberit.com.au/valves

The information contained herein is subject to change without notice. The information provided contains general description of the technical options available, which do not always apply to individual cases. The required features should therefore be invidvidually clarified in accordance with individual situations at the time of proceeding. All dimensions in mm (10mm = 1cm)

This publication GEAU037.2018 supersedes all previous publications. © Copyright Geberit Pty Ltd May 2018

inlet valves - geberit.com.authe geberit impuls380 cistern inlet valve art. no. 222.026.00.1 with...

Documents