install guideimages.idatalink.com/corporate/content/manuals/rsa-tl7...2018/11/22 · press and hold...
TRANSCRIPT
![Page 1: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/1.jpg)
Patent No. US 8,856,780 CA 2759622
20181121
REVISION DATE
ADS-RSA-TL7-[HC2352AC]
FIRMWARE
HC2352AC
HARDWARE
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED.
VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
ACCESSORIES
DOCUMENT NUMBER
2016 LEXUS IS200T PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2018
INSTALL GUIDE
TERMS OF USEAutomotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users.
![Page 2: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/2.jpg)
T001_H
T-HARNESS / COMPONENT LOCATOR - 1 OF 1
A
BC
PAGE 2 OF 8
Patent No. US 8,856,780 CA 2759622 2016 Lexus IS200t PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 3: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/3.jpg)
4
5
3
1
T001_H
1
3
4
2
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
NOT REQUIRED FOR BASIC INSTALLATION.INSERT WIRE TERMINALS IN MS3 CONNECTOR FOR OPTIONAL OUTPUTS.REFER TO PRODUCT GUIDE FOR MORE INFORMATION.
T-HARNESS / WIRING DIAGRAM - 1 OF 1
2: WHITE
1
1: BODY ECU
M5
M4
M2
M3
0404
03030404
PTS SWITCH (A)
MAIN BODY ECU, DRIVER SIDE DASH (B)
0606
08
010102020303
0505
0707
0909
11111212
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01010202
050506060707080809091010
121213131414151516161717181819192020
0101
04040505
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
1010
HOOD SWITCH
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CONNECT IF VEHICLE IS NOTEQUIPPED WITH OEM HOOD PIN
TRUNK (-) PINK - 05
PTS (-) BLUE - 01
CONNECTION REQUIRED IF IDLE MODE IS DESIRED.
03030202
0606
1111
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
JS4
MS3
MS1
VS3
VS4
JS8
TL6
RED/WHITE•BLACK DOT - TRUNK (-) OUTPUTRED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
GREEN/BLACK•BLACK DOTGREEN/BLACK•BLACK DOTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUT
PURPLEPURPLE
VS1
VS2
MS2
1: BODY ECU HARNESS
NCNC
JS7
TL2/7
JS6
!
2
2
SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.
6
5 4 3 2 1
10 9 8 7
16
28
15
27
14
26
13
25
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4 3 2 1
STEERING LOCK (C)
JS1 JS2
1: STEERING LOCK
1: STEERING LOCK HARNESS
JS5
M1
04
010102020303
0505
07070808
0606
!
M3
M1
M2 M5M4
PAGE 3 OF 8
Patent No. US 8,856,780 CA 2759622 2016 Lexus IS200t PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 4: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/4.jpg)
T001_W
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
A
B
CD
PAGE 4 OF 8
Patent No. US 8,856,780 CA 2759622 2016 Lexus IS200t PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 5: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/5.jpg)
4
!
3
10 11 12 13 14 15 16
1 2 3 4 5 6
14
6 7 8
9
10 11 12 13 14 15 16 17 18
19 20 21 22 23 24 25 26 27 29 30
1 2 3 4 5 6
7 8
29
2
8 9
28
7 6 5 4 3 2 1
1
1
3
1
2
2
6
5 4 3 2 1
10 9 8 7
164
7
8
9
19
1
2
3
20
21
10
11
12
22
23
24
13
14
15
25
26
27
17
18
28
5
6
T001_W
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
HARDWIRE / WIRING DIAGRAM - 1 OF 1
1
1
1
PTS (-) BLUE - 01
M5
M4
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
03 BROWN/RED - CANH 103 BROWN/RED - CANH 104 BROWN/YELLOW - CANL 104 BROWN/YELLOW - CANL 1
1: WHITE
2: WHITE
MAIN BODY ECU, DRIVER SIDE DASH (C)
STEERING LOCK (D)
CANH (DATA) WHITE - 06
CANL (DATA) BLACK - 14
AUTOLIGHT (-) PINK - 08
LOCK (-) BLUE - 29
UNLOCK (-) LTGREEN - 02
PTS SWITCH (A)
OBDII (B)
06 BLUE/WHITE•BLACK DOT06 BLUE/WHITE•BLACK DOT
08 WHITE/PURPLE•BLACK DOT
01 GREEN•BLACK DOT - LOCK (-) OUTPUT01 GREEN•BLACK DOT - LOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT
07 EMPTY07 EMPTY
09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT12 WHITE•BLACK DOT12 WHITE•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01 EMPTY01 EMPTY02 EMPTY02 EMPTY
05 BLUE/RED05 BLUE/RED06 BLUE/YELLOW06 BLUE/YELLOW07 EMPTY07 EMPTY08 ORANGE08 ORANGE09 YELLOW09 YELLOW10 EMPTY10 EMPTY11 GRAY/RED11 GRAY/RED12 GRAY/YELLOW12 GRAY/YELLOW13 GREEN/RED - SLP (-) OUTPUT13 GREEN/RED - SLP (-) OUTPUT14 ORANGE/WHITE14 ORANGE/WHITE15 BROWN15 BROWN16 ORANGE/BLACK - GROUND (-) INPUT16 ORANGE/BLACK - GROUND (-) INPUT17 PINK - IGNITION (+) IN/OUT17 PINK - IGNITION (+) IN/OUT18 PURPLE18 PURPLE19 RED - 12V (+) INPUT19 RED - 12V (+) INPUT20 BLACK - GROUND (-)20 BLACK - GROUND (-)
01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE03 GRAY/RED•BLUE DOT03 GRAY/RED•BLUE DOT04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE05 GRAY•BLUE DOT - GROUND (-) INPUT05 GRAY•BLUE DOT - GROUND (-) INPUT06 WHITE•BLUE DOT06 WHITE•BLUE DOT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
HORN (-)
TRUNK (-) PINK - 05
SLP (-) RED - 04
IGNITION (+) BLACK - 06
12V (+) GREEN - 07
HOOD SWITCH
1
2
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
WITHOUT OEM HOOD STATUS ONLY
CONNECTION REQUIRED ONLY IF IDLE MODE IS DESIREDM1
04 PINK/WHITE
01 ORANGE01 ORANGE02 RED02 RED03 PURPLE03 PURPLE
05 PINK05 PINK
07 RED07 RED08 BLACK08 BLACK
06 WHITE06 WHITE
!
M3
M1
M2 M5M4
PAGE 5 OF 8
Patent No. US 8,856,780 CA 2759622 2016 Lexus IS200t PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 6: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/6.jpg)
01
ENGINE
START
STOP
STOP ACC ON STARTON
02
03
ENGINE
START
STOP
STOP ACC ON STARTSTOP
04
05
ENGINE
START
STOP
STOP ACC ON STARTON
06
07
ENGINE
START
STOP
STOP ACC ON STARTSTOP
08
ENGINE
START
STOP
STOP ACC ON STARTSTART
09
10
11
12
13
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Push start button twice [2x] to ON position.
Wait, if LED 1 turns solid GREEN for 2 seconds, proceed to step 7. If LED 1 flashes GREEN rapidly, proceed to step 3.
Push start button once [1x] to OFF position.
Wait, LED 1 will turn solid RED. (This may take up to 5 minutes.)
Push start button twice [2x] to ON position.
Wait, LED 1 will turn solid GREEN for 2 seconds.
Push start button once [1x] to OFF position.
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming button.
Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
PAGE 6 OF 8
Patent No. US 8,856,780 CA 2759622 2016 Lexus IS200t PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 7: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/7.jpg)
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
4 Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
11 Open hood.
12If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
PAGE 7 OF 8
Patent No. US 8,856,780 CA 2759622 2016 Lexus IS200t PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 8: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/8.jpg)
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
PAGE 8 OF 8
Patent No. US 8,856,780 CA 2759622 2016 Lexus IS200t PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 9: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/9.jpg)
Patent No. US 8,856,780 CA 2759622
20181121
REVISION DATE
ADS-RSA-TL7-[HC2352AC]
FIRMWARE
HC2352AC
HARDWARE
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED.
VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
ACCESSORIES
DOCUMENT NUMBER
2017 LEXUS IS200T PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2018
INSTALL GUIDE
TERMS OF USEAutomotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users.
![Page 10: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/10.jpg)
T010_H
T-HARNESS / COMPONENT LOCATOR - 1 OF 1
A
BC
PAGE 2 OF 8
Patent No. US 8,856,780 CA 2759622 2017 Lexus IS200t PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 11: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/11.jpg)
4
5
3
1
T010_H
1
3
4
2
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
NOT REQUIRED FOR BASIC INSTALLATION.INSERT WIRE TERMINALS IN MS3 CONNECTOR FOR OPTIONAL OUTPUTS.REFER TO PRODUCT GUIDE FOR MORE INFORMATION.
T-HARNESS / WIRING DIAGRAM - 1 OF 1
2: WHITE
1
1: BODY ECU
M5
M4
M2
M3
0404
03030404
PTS SWITCH (A)
MAIN BODY ECU, DRIVER SIDE DASH (B)
0606
08
010102020303
0505
0707
0909
11111212
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01010202
050506060707080809091010
121213131414151516161717181819192020
0101
04040505
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
1010
HOOD SWITCH
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CONNECT IF VEHICLE IS NOTEQUIPPED WITH OEM HOOD PIN
TRUNK (-) PINK - 05
PTS (-) BLUE - 01
CONNECTION REQUIRED IF IDLE MODE IS DESIRED.
03030202
0606
1111
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
JS4
MS3
MS1
VS3
VS4
JS8
TL6
RED/WHITE•BLACK DOT - TRUNK (-) OUTPUTRED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
GREEN/BLACK•BLACK DOTGREEN/BLACK•BLACK DOTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUT
PURPLEPURPLE
VS1
VS2
MS2
1: BODY ECU HARNESS
NCNC
JS7
TL2/7
JS6
!
2
2
SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.
6
5 4 3 2 1
10 9 8 7
16
28
15
27
14
26
13
25
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4 3 2 1
STEERING LOCK (C)
JS1 JS2
1: STEERING LOCK
1: STEERING LOCK HARNESS
JS5
M1
04
010102020303
0505
07070808
0606
!
M3
M1
M2 M5M4
PAGE 3 OF 8
Patent No. US 8,856,780 CA 2759622 2017 Lexus IS200t PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 12: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/12.jpg)
T010_W
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
A
B
C
PAGE 4 OF 8
Patent No. US 8,856,780 CA 2759622 2017 Lexus IS200t PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 13: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/13.jpg)
4
!
10 11 12 13 14 15 16 17 18
19 20 21 22 23 24 25 26 27 29 30
1 2 3 4 5 6
7 8
29
2
8 9
28
7 6 5 4 3 2 1
6
5 4 3 2 1
10 9 8 7
164
7
8
9
19
1
2
3
20
21
10
11
12
22
23
24
13
14
15
25
26
27
17
18
28
5
6
T010_W
1
1
1
3
3
2
2
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
HARDWIRE / WIRING DIAGRAM - 1 OF 1
1
1
PTS (-) BLUE - 01
M5
M4
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
03 BROWN/RED - CANH 103 BROWN/RED - CANH 104 BROWN/YELLOW - CANL 104 BROWN/YELLOW - CANL 1
1: WHITE
2: WHITE
MAIN BODY ECU, DRIVER SIDE DASH (B)
STEERING LOCK (C)
CANH (DATA) YELLOW - 14
CANL (DATA) BLACK - 13
PTS SWITCH (A)
06 BLUE/WHITE•BLACK DOT06 BLUE/WHITE•BLACK DOT
08 WHITE/PURPLE•BLACK DOT
01 GREEN•BLACK DOT - LOCK (-) OUTPUT01 GREEN•BLACK DOT - LOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT
07 EMPTY07 EMPTY
09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT12 WHITE•BLACK DOT12 WHITE•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01 EMPTY01 EMPTY02 EMPTY02 EMPTY
05 BLUE/RED05 BLUE/RED06 BLUE/YELLOW06 BLUE/YELLOW07 EMPTY07 EMPTY08 ORANGE08 ORANGE09 YELLOW09 YELLOW10 EMPTY10 EMPTY11 GRAY/RED11 GRAY/RED12 GRAY/YELLOW12 GRAY/YELLOW13 GREEN/RED - SLP (-) OUTPUT13 GREEN/RED - SLP (-) OUTPUT14 ORANGE/WHITE14 ORANGE/WHITE15 BROWN15 BROWN16 ORANGE/BLACK - GROUND (-) INPUT16 ORANGE/BLACK - GROUND (-) INPUT17 PINK - IGNITION (+) IN/OUT17 PINK - IGNITION (+) IN/OUT18 PURPLE18 PURPLE19 RED - 12V (+) INPUT19 RED - 12V (+) INPUT20 BLACK - GROUND (-)20 BLACK - GROUND (-)
01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE03 GRAY/RED•BLUE DOT03 GRAY/RED•BLUE DOT04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE05 GRAY•BLUE DOT - GROUND (-) INPUT05 GRAY•BLUE DOT - GROUND (-) INPUT06 WHITE•BLUE DOT06 WHITE•BLUE DOT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
HORN (-)
TRUNK (-) PINK - 05
SLP (-) RED - 04
IGNITION (+) BLACK - 06
12V (+) GREEN - 07
HOOD SWITCH
1
2
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE.
WITHOUT OEM HOOD STATUS ONLY
CONNECTION REQUIRED ONLY IF IDLE MODE IS DESIRED
AUTOLIGHT (-) PINK - 08
LOCK (-) BLUE - 29
UNLOCK (-) LTGREEN - 02
M1
04 PINK/WHITE
01 ORANGE01 ORANGE02 RED02 RED03 PURPLE03 PURPLE
05 PINK05 PINK
07 RED07 RED08 BLACK08 BLACK
06 WHITE06 WHITE
!
M3
M1
M2 M5M4
PAGE 5 OF 8
Patent No. US 8,856,780 CA 2759622 2017 Lexus IS200t PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 14: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/14.jpg)
01
ENGINE
START
STOP
STOP ACC ON STARTON
02
03
ENGINE
START
STOP
STOP ACC ON STARTSTOP
04
05
ENGINE
START
STOP
STOP ACC ON STARTON
06
07
ENGINE
START
STOP
STOP ACC ON STARTSTOP
08
ENGINE
START
STOP
STOP ACC ON STARTSTART
09
10
11
12
13
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Push start button twice [2x] to ON position.
Wait, if LED 1 turns solid GREEN for 2 seconds, proceed to step 7. If LED 1 flashes GREEN rapidly, proceed to step 3.
Push start button once [1x] to OFF position.
Wait, LED 1 will turn solid RED. (This may take up to 5 minutes.)
Push start button twice [2x] to ON position.
Wait, LED 1 will turn solid GREEN for 2 seconds.
Push start button once [1x] to OFF position.
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming button.
Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
PAGE 6 OF 8
Patent No. US 8,856,780 CA 2759622 2017 Lexus IS200t PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 15: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/15.jpg)
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
4 Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
11 Open hood.
12If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
PAGE 7 OF 8
Patent No. US 8,856,780 CA 2759622 2017 Lexus IS200t PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 16: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/16.jpg)
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
PAGE 8 OF 8
Patent No. US 8,856,780 CA 2759622 2017 Lexus IS200t PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 17: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/17.jpg)
Patent No. US 8,856,780 CA 2759622
20181121
REVISION DATE
ADS-RSA-TL7-[HC2352AC]
FIRMWARE
HC2352AC
HARDWARE
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED.
VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
ACCESSORIES
DOCUMENT NUMBER
2014-2015 LEXUS IS250 PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2018
INSTALL GUIDE
TERMS OF USEAutomotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users.
![Page 18: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/18.jpg)
T001_H
T-HARNESS / COMPONENT LOCATOR - 1 OF 1
A
BC
PAGE 2 OF 8
Patent No. US 8,856,780 CA 2759622 2014-2015 Lexus IS250 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 19: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/19.jpg)
4
5
3
1
T001_H
1
3
4
2
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
NOT REQUIRED FOR BASIC INSTALLATION.INSERT WIRE TERMINALS IN MS3 CONNECTOR FOR OPTIONAL OUTPUTS.REFER TO PRODUCT GUIDE FOR MORE INFORMATION.
T-HARNESS / WIRING DIAGRAM - 1 OF 1
2: WHITE
1
1: BODY ECU
M5
M4
M2
M3
0404
03030404
PTS SWITCH (A)
MAIN BODY ECU, DRIVER SIDE DASH (B)
0606
08
010102020303
0505
0707
0909
11111212
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01010202
050506060707080809091010
121213131414151516161717181819192020
0101
04040505
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
1010
HOOD SWITCH
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CONNECT IF VEHICLE IS NOTEQUIPPED WITH OEM HOOD PIN
TRUNK (-) PINK - 05
PTS (-) BLUE - 01
CONNECTION REQUIRED IF IDLE MODE IS DESIRED.
03030202
0606
1111
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
JS4
MS3
MS1
VS3
VS4
JS8
TL6
RED/WHITE•BLACK DOT - TRUNK (-) OUTPUTRED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
GREEN/BLACK•BLACK DOTGREEN/BLACK•BLACK DOTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUT
PURPLEPURPLE
VS1
VS2
MS2
1: BODY ECU HARNESS
NCNC
JS7
TL2/7
JS6
!
2
2
SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.
6
5 4 3 2 1
10 9 8 7
16
28
15
27
14
26
13
25
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4 3 2 1
STEERING LOCK (C)
JS1 JS2
1: STEERING LOCK
1: STEERING LOCK HARNESS
JS5
M1
04
010102020303
0505
07070808
0606
!
M3
M1
M2 M5M4
PAGE 3 OF 8
Patent No. US 8,856,780 CA 2759622 2014-2015 Lexus IS250 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 20: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/20.jpg)
T001_W
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
A
B
CD
PAGE 4 OF 8
Patent No. US 8,856,780 CA 2759622 2014-2015 Lexus IS250 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 21: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/21.jpg)
4
!
3
10 11 12 13 14 15 16
1 2 3 4 5 6
14
6 7 8
9
10 11 12 13 14 15 16 17 18
19 20 21 22 23 24 25 26 27 29 30
1 2 3 4 5 6
7 8
29
2
8 9
28
7 6 5 4 3 2 1
1
1
3
1
2
2
6
5 4 3 2 1
10 9 8 7
164
7
8
9
19
1
2
3
20
21
10
11
12
22
23
24
13
14
15
25
26
27
17
18
28
5
6
T001_W
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
HARDWIRE / WIRING DIAGRAM - 1 OF 1
1
1
1
PTS (-) BLUE - 01
M5
M4
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
03 BROWN/RED - CANH 103 BROWN/RED - CANH 104 BROWN/YELLOW - CANL 104 BROWN/YELLOW - CANL 1
1: WHITE
2: WHITE
MAIN BODY ECU, DRIVER SIDE DASH (C)
STEERING LOCK (D)
CANH (DATA) WHITE - 06
CANL (DATA) BLACK - 14
AUTOLIGHT (-) PINK - 08
LOCK (-) BLUE - 29
UNLOCK (-) LTGREEN - 02
PTS SWITCH (A)
OBDII (B)
06 BLUE/WHITE•BLACK DOT06 BLUE/WHITE•BLACK DOT
08 WHITE/PURPLE•BLACK DOT
01 GREEN•BLACK DOT - LOCK (-) OUTPUT01 GREEN•BLACK DOT - LOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT
07 EMPTY07 EMPTY
09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT12 WHITE•BLACK DOT12 WHITE•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01 EMPTY01 EMPTY02 EMPTY02 EMPTY
05 BLUE/RED05 BLUE/RED06 BLUE/YELLOW06 BLUE/YELLOW07 EMPTY07 EMPTY08 ORANGE08 ORANGE09 YELLOW09 YELLOW10 EMPTY10 EMPTY11 GRAY/RED11 GRAY/RED12 GRAY/YELLOW12 GRAY/YELLOW13 GREEN/RED - SLP (-) OUTPUT13 GREEN/RED - SLP (-) OUTPUT14 ORANGE/WHITE14 ORANGE/WHITE15 BROWN15 BROWN16 ORANGE/BLACK - GROUND (-) INPUT16 ORANGE/BLACK - GROUND (-) INPUT17 PINK - IGNITION (+) IN/OUT17 PINK - IGNITION (+) IN/OUT18 PURPLE18 PURPLE19 RED - 12V (+) INPUT19 RED - 12V (+) INPUT20 BLACK - GROUND (-)20 BLACK - GROUND (-)
01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE03 GRAY/RED•BLUE DOT03 GRAY/RED•BLUE DOT04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE05 GRAY•BLUE DOT - GROUND (-) INPUT05 GRAY•BLUE DOT - GROUND (-) INPUT06 WHITE•BLUE DOT06 WHITE•BLUE DOT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
HORN (-)
TRUNK (-) PINK - 05
SLP (-) RED - 04
IGNITION (+) BLACK - 06
12V (+) GREEN - 07
HOOD SWITCH
1
2
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
WITHOUT OEM HOOD STATUS ONLY
CONNECTION REQUIRED ONLY IF IDLE MODE IS DESIREDM1
04 PINK/WHITE
01 ORANGE01 ORANGE02 RED02 RED03 PURPLE03 PURPLE
05 PINK05 PINK
07 RED07 RED08 BLACK08 BLACK
06 WHITE06 WHITE
!
M3
M1
M2 M5M4
PAGE 5 OF 8
Patent No. US 8,856,780 CA 2759622 2014-2015 Lexus IS250 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 22: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/22.jpg)
01
ENGINE
START
STOP
STOP ACC ON STARTON
02
03
ENGINE
START
STOP
STOP ACC ON STARTSTOP
04
05
ENGINE
START
STOP
STOP ACC ON STARTON
06
07
ENGINE
START
STOP
STOP ACC ON STARTSTOP
08
ENGINE
START
STOP
STOP ACC ON STARTSTART
09
10
11
12
13
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Push start button twice [2x] to ON position.
Wait, if LED 1 turns solid GREEN for 2 seconds, proceed to step 7. If LED 1 flashes GREEN rapidly, proceed to step 3.
Push start button once [1x] to OFF position.
Wait, LED 1 will turn solid RED. (This may take up to 5 minutes.)
Push start button twice [2x] to ON position.
Wait, LED 1 will turn solid GREEN for 2 seconds.
Push start button once [1x] to OFF position.
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming button.
Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
PAGE 6 OF 8
Patent No. US 8,856,780 CA 2759622 2014-2015 Lexus IS250 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 23: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/23.jpg)
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
4 Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
11 Open hood.
12If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
PAGE 7 OF 8
Patent No. US 8,856,780 CA 2759622 2014-2015 Lexus IS250 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 24: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/24.jpg)
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
PAGE 8 OF 8
Patent No. US 8,856,780 CA 2759622 2014-2015 Lexus IS250 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 25: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/25.jpg)
Patent No. US 8,856,780 CA 2759622
20181121
REVISION DATE
ADS-RSA-TL7-[HC2352AC]
FIRMWARE
HC2352AC
HARDWARE
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED.
VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
ACCESSORIES
DOCUMENT NUMBER
2016 LEXUS IS300 PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2018
INSTALL GUIDE
TERMS OF USEAutomotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users.
![Page 26: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/26.jpg)
T001_H
T-HARNESS / COMPONENT LOCATOR - 1 OF 1
A
BC
PAGE 2 OF 8
Patent No. US 8,856,780 CA 2759622 2016 Lexus IS300 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 27: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/27.jpg)
4
5
3
1
T001_H
1
3
4
2
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
NOT REQUIRED FOR BASIC INSTALLATION.INSERT WIRE TERMINALS IN MS3 CONNECTOR FOR OPTIONAL OUTPUTS.REFER TO PRODUCT GUIDE FOR MORE INFORMATION.
T-HARNESS / WIRING DIAGRAM - 1 OF 1
2: WHITE
1
1: BODY ECU
M5
M4
M2
M3
0404
03030404
PTS SWITCH (A)
MAIN BODY ECU, DRIVER SIDE DASH (B)
0606
08
010102020303
0505
0707
0909
11111212
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01010202
050506060707080809091010
121213131414151516161717181819192020
0101
04040505
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
1010
HOOD SWITCH
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CONNECT IF VEHICLE IS NOTEQUIPPED WITH OEM HOOD PIN
TRUNK (-) PINK - 05
PTS (-) BLUE - 01
CONNECTION REQUIRED IF IDLE MODE IS DESIRED.
03030202
0606
1111
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
JS4
MS3
MS1
VS3
VS4
JS8
TL6
RED/WHITE•BLACK DOT - TRUNK (-) OUTPUTRED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
GREEN/BLACK•BLACK DOTGREEN/BLACK•BLACK DOTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUT
PURPLEPURPLE
VS1
VS2
MS2
1: BODY ECU HARNESS
NCNC
JS7
TL2/7
JS6
!
2
2
SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.
6
5 4 3 2 1
10 9 8 7
16
28
15
27
14
26
13
25
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4 3 2 1
STEERING LOCK (C)
JS1 JS2
1: STEERING LOCK
1: STEERING LOCK HARNESS
JS5
M1
04
010102020303
0505
07070808
0606
!
M3
M1
M2 M5M4
PAGE 3 OF 8
Patent No. US 8,856,780 CA 2759622 2016 Lexus IS300 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 28: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/28.jpg)
T001_W
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
A
B
CD
PAGE 4 OF 8
Patent No. US 8,856,780 CA 2759622 2016 Lexus IS300 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 29: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/29.jpg)
4
!
3
10 11 12 13 14 15 16
1 2 3 4 5 6
14
6 7 8
9
10 11 12 13 14 15 16 17 18
19 20 21 22 23 24 25 26 27 29 30
1 2 3 4 5 6
7 8
29
2
8 9
28
7 6 5 4 3 2 1
1
1
3
1
2
2
6
5 4 3 2 1
10 9 8 7
164
7
8
9
19
1
2
3
20
21
10
11
12
22
23
24
13
14
15
25
26
27
17
18
28
5
6
T001_W
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
HARDWIRE / WIRING DIAGRAM - 1 OF 1
1
1
1
PTS (-) BLUE - 01
M5
M4
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
03 BROWN/RED - CANH 103 BROWN/RED - CANH 104 BROWN/YELLOW - CANL 104 BROWN/YELLOW - CANL 1
1: WHITE
2: WHITE
MAIN BODY ECU, DRIVER SIDE DASH (C)
STEERING LOCK (D)
CANH (DATA) WHITE - 06
CANL (DATA) BLACK - 14
AUTOLIGHT (-) PINK - 08
LOCK (-) BLUE - 29
UNLOCK (-) LTGREEN - 02
PTS SWITCH (A)
OBDII (B)
06 BLUE/WHITE•BLACK DOT06 BLUE/WHITE•BLACK DOT
08 WHITE/PURPLE•BLACK DOT
01 GREEN•BLACK DOT - LOCK (-) OUTPUT01 GREEN•BLACK DOT - LOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT
07 EMPTY07 EMPTY
09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT12 WHITE•BLACK DOT12 WHITE•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01 EMPTY01 EMPTY02 EMPTY02 EMPTY
05 BLUE/RED05 BLUE/RED06 BLUE/YELLOW06 BLUE/YELLOW07 EMPTY07 EMPTY08 ORANGE08 ORANGE09 YELLOW09 YELLOW10 EMPTY10 EMPTY11 GRAY/RED11 GRAY/RED12 GRAY/YELLOW12 GRAY/YELLOW13 GREEN/RED - SLP (-) OUTPUT13 GREEN/RED - SLP (-) OUTPUT14 ORANGE/WHITE14 ORANGE/WHITE15 BROWN15 BROWN16 ORANGE/BLACK - GROUND (-) INPUT16 ORANGE/BLACK - GROUND (-) INPUT17 PINK - IGNITION (+) IN/OUT17 PINK - IGNITION (+) IN/OUT18 PURPLE18 PURPLE19 RED - 12V (+) INPUT19 RED - 12V (+) INPUT20 BLACK - GROUND (-)20 BLACK - GROUND (-)
01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE03 GRAY/RED•BLUE DOT03 GRAY/RED•BLUE DOT04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE05 GRAY•BLUE DOT - GROUND (-) INPUT05 GRAY•BLUE DOT - GROUND (-) INPUT06 WHITE•BLUE DOT06 WHITE•BLUE DOT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
HORN (-)
TRUNK (-) PINK - 05
SLP (-) RED - 04
IGNITION (+) BLACK - 06
12V (+) GREEN - 07
HOOD SWITCH
1
2
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
WITHOUT OEM HOOD STATUS ONLY
CONNECTION REQUIRED ONLY IF IDLE MODE IS DESIREDM1
04 PINK/WHITE
01 ORANGE01 ORANGE02 RED02 RED03 PURPLE03 PURPLE
05 PINK05 PINK
07 RED07 RED08 BLACK08 BLACK
06 WHITE06 WHITE
!
M3
M1
M2 M5M4
PAGE 5 OF 8
Patent No. US 8,856,780 CA 2759622 2016 Lexus IS300 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 30: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/30.jpg)
01
ENGINE
START
STOP
STOP ACC ON STARTON
02
03
ENGINE
START
STOP
STOP ACC ON STARTSTOP
04
05
ENGINE
START
STOP
STOP ACC ON STARTON
06
07
ENGINE
START
STOP
STOP ACC ON STARTSTOP
08
ENGINE
START
STOP
STOP ACC ON STARTSTART
09
10
11
12
13
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Push start button twice [2x] to ON position.
Wait, if LED 1 turns solid GREEN for 2 seconds, proceed to step 7. If LED 1 flashes GREEN rapidly, proceed to step 3.
Push start button once [1x] to OFF position.
Wait, LED 1 will turn solid RED. (This may take up to 5 minutes.)
Push start button twice [2x] to ON position.
Wait, LED 1 will turn solid GREEN for 2 seconds.
Push start button once [1x] to OFF position.
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming button.
Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
PAGE 6 OF 8
Patent No. US 8,856,780 CA 2759622 2016 Lexus IS300 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 31: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/31.jpg)
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
4 Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
11 Open hood.
12If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
PAGE 7 OF 8
Patent No. US 8,856,780 CA 2759622 2016 Lexus IS300 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 32: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/32.jpg)
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
PAGE 8 OF 8
Patent No. US 8,856,780 CA 2759622 2016 Lexus IS300 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 33: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/33.jpg)
Patent No. US 8,856,780 CA 2759622
20181121
REVISION DATE
ADS-RSA-TL7-[HC2352AC]
FIRMWARE
HC2352AC
HARDWARE
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED.
VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
ACCESSORIES
DOCUMENT NUMBER
2017-2018 LEXUS IS300 PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2018
INSTALL GUIDE
TERMS OF USEAutomotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users.
![Page 34: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/34.jpg)
T010_H
T-HARNESS / COMPONENT LOCATOR - 1 OF 1
A
BC
PAGE 2 OF 8
Patent No. US 8,856,780 CA 2759622 2017-2018 Lexus IS300 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 35: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/35.jpg)
4
5
3
1
T010_H
1
3
4
2
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
NOT REQUIRED FOR BASIC INSTALLATION.INSERT WIRE TERMINALS IN MS3 CONNECTOR FOR OPTIONAL OUTPUTS.REFER TO PRODUCT GUIDE FOR MORE INFORMATION.
T-HARNESS / WIRING DIAGRAM - 1 OF 1
2: WHITE
1
1: BODY ECU
M5
M4
M2
M3
0404
03030404
PTS SWITCH (A)
MAIN BODY ECU, DRIVER SIDE DASH (B)
0606
08
010102020303
0505
0707
0909
11111212
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01010202
050506060707080809091010
121213131414151516161717181819192020
0101
04040505
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
1010
HOOD SWITCH
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CONNECT IF VEHICLE IS NOTEQUIPPED WITH OEM HOOD PIN
TRUNK (-) PINK - 05
PTS (-) BLUE - 01
CONNECTION REQUIRED IF IDLE MODE IS DESIRED.
03030202
0606
1111
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
JS4
MS3
MS1
VS3
VS4
JS8
TL6
RED/WHITE•BLACK DOT - TRUNK (-) OUTPUTRED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
GREEN/BLACK•BLACK DOTGREEN/BLACK•BLACK DOTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUT
PURPLEPURPLE
VS1
VS2
MS2
1: BODY ECU HARNESS
NCNC
JS7
TL2/7
JS6
!
2
2
SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.
6
5 4 3 2 1
10 9 8 7
16
28
15
27
14
26
13
25
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4 3 2 1
STEERING LOCK (C)
JS1 JS2
1: STEERING LOCK
1: STEERING LOCK HARNESS
JS5
M1
04
010102020303
0505
07070808
0606
!
M3
M1
M2 M5M4
PAGE 3 OF 8
Patent No. US 8,856,780 CA 2759622 2017-2018 Lexus IS300 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 36: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/36.jpg)
T010_W
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
A
B
C
PAGE 4 OF 8
Patent No. US 8,856,780 CA 2759622 2017-2018 Lexus IS300 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 37: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/37.jpg)
4
!
10 11 12 13 14 15 16 17 18
19 20 21 22 23 24 25 26 27 29 30
1 2 3 4 5 6
7 8
29
2
8 9
28
7 6 5 4 3 2 1
6
5 4 3 2 1
10 9 8 7
164
7
8
9
19
1
2
3
20
21
10
11
12
22
23
24
13
14
15
25
26
27
17
18
28
5
6
T010_W
1
1
1
3
3
2
2
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
HARDWIRE / WIRING DIAGRAM - 1 OF 1
1
1
PTS (-) BLUE - 01
M5
M4
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
03 BROWN/RED - CANH 103 BROWN/RED - CANH 104 BROWN/YELLOW - CANL 104 BROWN/YELLOW - CANL 1
1: WHITE
2: WHITE
MAIN BODY ECU, DRIVER SIDE DASH (B)
STEERING LOCK (C)
CANH (DATA) YELLOW - 14
CANL (DATA) BLACK - 13
PTS SWITCH (A)
06 BLUE/WHITE•BLACK DOT06 BLUE/WHITE•BLACK DOT
08 WHITE/PURPLE•BLACK DOT
01 GREEN•BLACK DOT - LOCK (-) OUTPUT01 GREEN•BLACK DOT - LOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT
07 EMPTY07 EMPTY
09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT12 WHITE•BLACK DOT12 WHITE•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01 EMPTY01 EMPTY02 EMPTY02 EMPTY
05 BLUE/RED05 BLUE/RED06 BLUE/YELLOW06 BLUE/YELLOW07 EMPTY07 EMPTY08 ORANGE08 ORANGE09 YELLOW09 YELLOW10 EMPTY10 EMPTY11 GRAY/RED11 GRAY/RED12 GRAY/YELLOW12 GRAY/YELLOW13 GREEN/RED - SLP (-) OUTPUT13 GREEN/RED - SLP (-) OUTPUT14 ORANGE/WHITE14 ORANGE/WHITE15 BROWN15 BROWN16 ORANGE/BLACK - GROUND (-) INPUT16 ORANGE/BLACK - GROUND (-) INPUT17 PINK - IGNITION (+) IN/OUT17 PINK - IGNITION (+) IN/OUT18 PURPLE18 PURPLE19 RED - 12V (+) INPUT19 RED - 12V (+) INPUT20 BLACK - GROUND (-)20 BLACK - GROUND (-)
01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE03 GRAY/RED•BLUE DOT03 GRAY/RED•BLUE DOT04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE05 GRAY•BLUE DOT - GROUND (-) INPUT05 GRAY•BLUE DOT - GROUND (-) INPUT06 WHITE•BLUE DOT06 WHITE•BLUE DOT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
HORN (-)
TRUNK (-) PINK - 05
SLP (-) RED - 04
IGNITION (+) BLACK - 06
12V (+) GREEN - 07
HOOD SWITCH
1
2
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE.
WITHOUT OEM HOOD STATUS ONLY
CONNECTION REQUIRED ONLY IF IDLE MODE IS DESIRED
AUTOLIGHT (-) PINK - 08
LOCK (-) BLUE - 29
UNLOCK (-) LTGREEN - 02
M1
04 PINK/WHITE
01 ORANGE01 ORANGE02 RED02 RED03 PURPLE03 PURPLE
05 PINK05 PINK
07 RED07 RED08 BLACK08 BLACK
06 WHITE06 WHITE
!
M3
M1
M2 M5M4
PAGE 5 OF 8
Patent No. US 8,856,780 CA 2759622 2017-2018 Lexus IS300 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 38: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/38.jpg)
01
ENGINE
START
STOP
STOP ACC ON STARTON
02
03
ENGINE
START
STOP
STOP ACC ON STARTSTOP
04
05
ENGINE
START
STOP
STOP ACC ON STARTON
06
07
ENGINE
START
STOP
STOP ACC ON STARTSTOP
08
ENGINE
START
STOP
STOP ACC ON STARTSTART
09
10
11
12
13
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Push start button twice [2x] to ON position.
Wait, if LED 1 turns solid GREEN for 2 seconds, proceed to step 7. If LED 1 flashes GREEN rapidly, proceed to step 3.
Push start button once [1x] to OFF position.
Wait, LED 1 will turn solid RED. (This may take up to 5 minutes.)
Push start button twice [2x] to ON position.
Wait, LED 1 will turn solid GREEN for 2 seconds.
Push start button once [1x] to OFF position.
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming button.
Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
PAGE 6 OF 8
Patent No. US 8,856,780 CA 2759622 2017-2018 Lexus IS300 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 39: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/39.jpg)
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
4 Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
11 Open hood.
12If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
PAGE 7 OF 8
Patent No. US 8,856,780 CA 2759622 2017-2018 Lexus IS300 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 40: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/40.jpg)
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
PAGE 8 OF 8
Patent No. US 8,856,780 CA 2759622 2017-2018 Lexus IS300 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 41: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/41.jpg)
Patent No. US 8,856,780 CA 2759622
20181121
REVISION DATE
ADS-RSA-TL7-[HC2352AC]
FIRMWARE
HC2352AC
HARDWARE
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED.
VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
ACCESSORIES
DOCUMENT NUMBER
2014-2016 LEXUS IS350 PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2018
INSTALL GUIDE
TERMS OF USEAutomotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users.
![Page 42: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/42.jpg)
T001_H
T-HARNESS / COMPONENT LOCATOR - 1 OF 1
A
BC
PAGE 2 OF 8
Patent No. US 8,856,780 CA 2759622 2014-2016 Lexus IS350 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 43: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/43.jpg)
4
5
3
1
T001_H
1
3
4
2
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
NOT REQUIRED FOR BASIC INSTALLATION.INSERT WIRE TERMINALS IN MS3 CONNECTOR FOR OPTIONAL OUTPUTS.REFER TO PRODUCT GUIDE FOR MORE INFORMATION.
T-HARNESS / WIRING DIAGRAM - 1 OF 1
2: WHITE
1
1: BODY ECU
M5
M4
M2
M3
0404
03030404
PTS SWITCH (A)
MAIN BODY ECU, DRIVER SIDE DASH (B)
0606
08
010102020303
0505
0707
0909
11111212
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01010202
050506060707080809091010
121213131414151516161717181819192020
0101
04040505
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
1010
HOOD SWITCH
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CONNECT IF VEHICLE IS NOTEQUIPPED WITH OEM HOOD PIN
TRUNK (-) PINK - 05
PTS (-) BLUE - 01
CONNECTION REQUIRED IF IDLE MODE IS DESIRED.
03030202
0606
1111
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
JS4
MS3
MS1
VS3
VS4
JS8
TL6
RED/WHITE•BLACK DOT - TRUNK (-) OUTPUTRED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
GREEN/BLACK•BLACK DOTGREEN/BLACK•BLACK DOTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUT
PURPLEPURPLE
VS1
VS2
MS2
1: BODY ECU HARNESS
NCNC
JS7
TL2/7
JS6
!
2
2
SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.
6
5 4 3 2 1
10 9 8 7
16
28
15
27
14
26
13
25
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4 3 2 1
STEERING LOCK (C)
JS1 JS2
1: STEERING LOCK
1: STEERING LOCK HARNESS
JS5
M1
04
010102020303
0505
07070808
0606
!
M3
M1
M2 M5M4
PAGE 3 OF 8
Patent No. US 8,856,780 CA 2759622 2014-2016 Lexus IS350 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 44: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/44.jpg)
T001_W
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
A
B
CD
PAGE 4 OF 8
Patent No. US 8,856,780 CA 2759622 2014-2016 Lexus IS350 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 45: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/45.jpg)
4
!
3
10 11 12 13 14 15 16
1 2 3 4 5 6
14
6 7 8
9
10 11 12 13 14 15 16 17 18
19 20 21 22 23 24 25 26 27 29 30
1 2 3 4 5 6
7 8
29
2
8 9
28
7 6 5 4 3 2 1
1
1
3
1
2
2
6
5 4 3 2 1
10 9 8 7
164
7
8
9
19
1
2
3
20
21
10
11
12
22
23
24
13
14
15
25
26
27
17
18
28
5
6
T001_W
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
HARDWIRE / WIRING DIAGRAM - 1 OF 1
1
1
1
PTS (-) BLUE - 01
M5
M4
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
03 BROWN/RED - CANH 103 BROWN/RED - CANH 104 BROWN/YELLOW - CANL 104 BROWN/YELLOW - CANL 1
1: WHITE
2: WHITE
MAIN BODY ECU, DRIVER SIDE DASH (C)
STEERING LOCK (D)
CANH (DATA) WHITE - 06
CANL (DATA) BLACK - 14
AUTOLIGHT (-) PINK - 08
LOCK (-) BLUE - 29
UNLOCK (-) LTGREEN - 02
PTS SWITCH (A)
OBDII (B)
06 BLUE/WHITE•BLACK DOT06 BLUE/WHITE•BLACK DOT
08 WHITE/PURPLE•BLACK DOT
01 GREEN•BLACK DOT - LOCK (-) OUTPUT01 GREEN•BLACK DOT - LOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT
07 EMPTY07 EMPTY
09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT12 WHITE•BLACK DOT12 WHITE•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01 EMPTY01 EMPTY02 EMPTY02 EMPTY
05 BLUE/RED05 BLUE/RED06 BLUE/YELLOW06 BLUE/YELLOW07 EMPTY07 EMPTY08 ORANGE08 ORANGE09 YELLOW09 YELLOW10 EMPTY10 EMPTY11 GRAY/RED11 GRAY/RED12 GRAY/YELLOW12 GRAY/YELLOW13 GREEN/RED - SLP (-) OUTPUT13 GREEN/RED - SLP (-) OUTPUT14 ORANGE/WHITE14 ORANGE/WHITE15 BROWN15 BROWN16 ORANGE/BLACK - GROUND (-) INPUT16 ORANGE/BLACK - GROUND (-) INPUT17 PINK - IGNITION (+) IN/OUT17 PINK - IGNITION (+) IN/OUT18 PURPLE18 PURPLE19 RED - 12V (+) INPUT19 RED - 12V (+) INPUT20 BLACK - GROUND (-)20 BLACK - GROUND (-)
01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE03 GRAY/RED•BLUE DOT03 GRAY/RED•BLUE DOT04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE05 GRAY•BLUE DOT - GROUND (-) INPUT05 GRAY•BLUE DOT - GROUND (-) INPUT06 WHITE•BLUE DOT06 WHITE•BLUE DOT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
HORN (-)
TRUNK (-) PINK - 05
SLP (-) RED - 04
IGNITION (+) BLACK - 06
12V (+) GREEN - 07
HOOD SWITCH
1
2
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
WITHOUT OEM HOOD STATUS ONLY
CONNECTION REQUIRED ONLY IF IDLE MODE IS DESIREDM1
04 PINK/WHITE
01 ORANGE01 ORANGE02 RED02 RED03 PURPLE03 PURPLE
05 PINK05 PINK
07 RED07 RED08 BLACK08 BLACK
06 WHITE06 WHITE
!
M3
M1
M2 M5M4
PAGE 5 OF 8
Patent No. US 8,856,780 CA 2759622 2014-2016 Lexus IS350 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 46: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/46.jpg)
01
ENGINE
START
STOP
STOP ACC ON STARTON
02
03
ENGINE
START
STOP
STOP ACC ON STARTSTOP
04
05
ENGINE
START
STOP
STOP ACC ON STARTON
06
07
ENGINE
START
STOP
STOP ACC ON STARTSTOP
08
ENGINE
START
STOP
STOP ACC ON STARTSTART
09
10
11
12
13
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Push start button twice [2x] to ON position.
Wait, if LED 1 turns solid GREEN for 2 seconds, proceed to step 7. If LED 1 flashes GREEN rapidly, proceed to step 3.
Push start button once [1x] to OFF position.
Wait, LED 1 will turn solid RED. (This may take up to 5 minutes.)
Push start button twice [2x] to ON position.
Wait, LED 1 will turn solid GREEN for 2 seconds.
Push start button once [1x] to OFF position.
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming button.
Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
PAGE 6 OF 8
Patent No. US 8,856,780 CA 2759622 2014-2016 Lexus IS350 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 47: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/47.jpg)
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
4 Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
11 Open hood.
12If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
PAGE 7 OF 8
Patent No. US 8,856,780 CA 2759622 2014-2016 Lexus IS350 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 48: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/48.jpg)
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
PAGE 8 OF 8
Patent No. US 8,856,780 CA 2759622 2014-2016 Lexus IS350 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 49: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/49.jpg)
Patent No. US 8,856,780 CA 2759622
20181121
REVISION DATE
ADS-RSA-TL7-[HC2352AC]
FIRMWARE
HC2352AC
HARDWARE
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED.
VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
ACCESSORIES
DOCUMENT NUMBER
2017-2018 LEXUS IS350 PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2018
INSTALL GUIDE
TERMS OF USEAutomotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users.
![Page 50: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/50.jpg)
T010_H
T-HARNESS / COMPONENT LOCATOR - 1 OF 1
A
BC
PAGE 2 OF 8
Patent No. US 8,856,780 CA 2759622 2017-2018 Lexus IS350 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 51: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/51.jpg)
4
5
3
1
T010_H
1
3
4
2
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
NOT REQUIRED FOR BASIC INSTALLATION.INSERT WIRE TERMINALS IN MS3 CONNECTOR FOR OPTIONAL OUTPUTS.REFER TO PRODUCT GUIDE FOR MORE INFORMATION.
T-HARNESS / WIRING DIAGRAM - 1 OF 1
2: WHITE
1
1: BODY ECU
M5
M4
M2
M3
0404
03030404
PTS SWITCH (A)
MAIN BODY ECU, DRIVER SIDE DASH (B)
0606
08
010102020303
0505
0707
0909
11111212
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01010202
050506060707080809091010
121213131414151516161717181819192020
0101
04040505
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
1010
HOOD SWITCH
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CONNECT IF VEHICLE IS NOTEQUIPPED WITH OEM HOOD PIN
TRUNK (-) PINK - 05
PTS (-) BLUE - 01
CONNECTION REQUIRED IF IDLE MODE IS DESIRED.
03030202
0606
1111
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
JS4
MS3
MS1
VS3
VS4
JS8
TL6
RED/WHITE•BLACK DOT - TRUNK (-) OUTPUTRED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
GREEN/BLACK•BLACK DOTGREEN/BLACK•BLACK DOTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUT
PURPLEPURPLE
VS1
VS2
MS2
1: BODY ECU HARNESS
NCNC
JS7
TL2/7
JS6
!
2
2
SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.
6
5 4 3 2 1
10 9 8 7
16
28
15
27
14
26
13
25
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4 3 2 1
STEERING LOCK (C)
JS1 JS2
1: STEERING LOCK
1: STEERING LOCK HARNESS
JS5
M1
04
010102020303
0505
07070808
0606
!
M3
M1
M2 M5M4
PAGE 3 OF 8
Patent No. US 8,856,780 CA 2759622 2017-2018 Lexus IS350 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 52: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/52.jpg)
T010_W
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
A
B
C
PAGE 4 OF 8
Patent No. US 8,856,780 CA 2759622 2017-2018 Lexus IS350 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 53: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/53.jpg)
4
!
10 11 12 13 14 15 16 17 18
19 20 21 22 23 24 25 26 27 29 30
1 2 3 4 5 6
7 8
29
2
8 9
28
7 6 5 4 3 2 1
6
5 4 3 2 1
10 9 8 7
164
7
8
9
19
1
2
3
20
21
10
11
12
22
23
24
13
14
15
25
26
27
17
18
28
5
6
T010_W
1
1
1
3
3
2
2
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
HARDWIRE / WIRING DIAGRAM - 1 OF 1
1
1
PTS (-) BLUE - 01
M5
M4
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
03 BROWN/RED - CANH 103 BROWN/RED - CANH 104 BROWN/YELLOW - CANL 104 BROWN/YELLOW - CANL 1
1: WHITE
2: WHITE
MAIN BODY ECU, DRIVER SIDE DASH (B)
STEERING LOCK (C)
CANH (DATA) YELLOW - 14
CANL (DATA) BLACK - 13
PTS SWITCH (A)
06 BLUE/WHITE•BLACK DOT06 BLUE/WHITE•BLACK DOT
08 WHITE/PURPLE•BLACK DOT
01 GREEN•BLACK DOT - LOCK (-) OUTPUT01 GREEN•BLACK DOT - LOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT
07 EMPTY07 EMPTY
09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT12 WHITE•BLACK DOT12 WHITE•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01 EMPTY01 EMPTY02 EMPTY02 EMPTY
05 BLUE/RED05 BLUE/RED06 BLUE/YELLOW06 BLUE/YELLOW07 EMPTY07 EMPTY08 ORANGE08 ORANGE09 YELLOW09 YELLOW10 EMPTY10 EMPTY11 GRAY/RED11 GRAY/RED12 GRAY/YELLOW12 GRAY/YELLOW13 GREEN/RED - SLP (-) OUTPUT13 GREEN/RED - SLP (-) OUTPUT14 ORANGE/WHITE14 ORANGE/WHITE15 BROWN15 BROWN16 ORANGE/BLACK - GROUND (-) INPUT16 ORANGE/BLACK - GROUND (-) INPUT17 PINK - IGNITION (+) IN/OUT17 PINK - IGNITION (+) IN/OUT18 PURPLE18 PURPLE19 RED - 12V (+) INPUT19 RED - 12V (+) INPUT20 BLACK - GROUND (-)20 BLACK - GROUND (-)
01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE03 GRAY/RED•BLUE DOT03 GRAY/RED•BLUE DOT04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE05 GRAY•BLUE DOT - GROUND (-) INPUT05 GRAY•BLUE DOT - GROUND (-) INPUT06 WHITE•BLUE DOT06 WHITE•BLUE DOT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
HORN (-)
TRUNK (-) PINK - 05
SLP (-) RED - 04
IGNITION (+) BLACK - 06
12V (+) GREEN - 07
HOOD SWITCH
1
2
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE.
WITHOUT OEM HOOD STATUS ONLY
CONNECTION REQUIRED ONLY IF IDLE MODE IS DESIRED
AUTOLIGHT (-) PINK - 08
LOCK (-) BLUE - 29
UNLOCK (-) LTGREEN - 02
M1
04 PINK/WHITE
01 ORANGE01 ORANGE02 RED02 RED03 PURPLE03 PURPLE
05 PINK05 PINK
07 RED07 RED08 BLACK08 BLACK
06 WHITE06 WHITE
!
M3
M1
M2 M5M4
PAGE 5 OF 8
Patent No. US 8,856,780 CA 2759622 2017-2018 Lexus IS350 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 54: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/54.jpg)
01
ENGINE
START
STOP
STOP ACC ON STARTON
02
03
ENGINE
START
STOP
STOP ACC ON STARTSTOP
04
05
ENGINE
START
STOP
STOP ACC ON STARTON
06
07
ENGINE
START
STOP
STOP ACC ON STARTSTOP
08
ENGINE
START
STOP
STOP ACC ON STARTSTART
09
10
11
12
13
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Push start button twice [2x] to ON position.
Wait, if LED 1 turns solid GREEN for 2 seconds, proceed to step 7. If LED 1 flashes GREEN rapidly, proceed to step 3.
Push start button once [1x] to OFF position.
Wait, LED 1 will turn solid RED. (This may take up to 5 minutes.)
Push start button twice [2x] to ON position.
Wait, LED 1 will turn solid GREEN for 2 seconds.
Push start button once [1x] to OFF position.
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming button.
Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
PAGE 6 OF 8
Patent No. US 8,856,780 CA 2759622 2017-2018 Lexus IS350 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 55: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/55.jpg)
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
4 Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
11 Open hood.
12If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
PAGE 7 OF 8
Patent No. US 8,856,780 CA 2759622 2017-2018 Lexus IS350 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 56: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/56.jpg)
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
PAGE 8 OF 8
Patent No. US 8,856,780 CA 2759622 2017-2018 Lexus IS350 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 57: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/57.jpg)
Patent No. US 8,856,780 CA 2759622
20181121
REVISION DATE
ADS-RSA-TL7-[HC2352AC]
FIRMWARE
HC2352AC
HARDWARE
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED.
VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
ACCESSORIES
DOCUMENT NUMBER
2016-2018 LEXUS LX570 PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2018
INSTALL GUIDE
TERMS OF USEAutomotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users.
![Page 58: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/58.jpg)
T006_H
T-HARNESS / COMPONENT LOCATOR - 1 OF 1
A
B
C
PAGE 2 OF 8
Patent No. US 8,856,780 CA 2759622 2016-2018 Lexus LX570 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 59: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/59.jpg)
4
5
3
1
T006_H
1
3
4
2
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
NOT REQUIRED FOR BASIC INSTALLATION.INSERT WIRE TERMINALS IN MS3 CONNECTOR FOR OPTIONAL OUTPUTS.REFER TO PRODUCT GUIDE FOR MORE INFORMATION.
T-HARNESS / WIRING DIAGRAM - 1 OF 1
2: WHITE
1
1: BODY ECU
M5
M4
M2
M3
0404
03030404
PTS SWITCH (A)
MAIN BODY ECU, DRIVER SIDE DASH (B)
0606
08
010102020303
0505
0707
0909
11111212
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01010202
050506060707080809091010
121213131414151516161717181819192020
0101
04040505
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
1010
HOOD SWITCH
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CONNECT IF VEHICLE IS NOTEQUIPPED WITH OEM HOOD PIN
POWER LIFTGATE (-) RED - 05
PTS (-) BLUE - 01
CONNECTION REQUIRED IF IDLE MODE IS DESIRED.
03030202
0606
1111
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
JS4
MS3
MS1
VS3
VS4JS8
TL6
RED/WHITE•BLACK DOT - TRUNK (-) OUTPUTRED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
GREEN/BLACK•BLACK DOTGREEN/BLACK•BLACK DOTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUT
PURPLEPURPLE
VS1
VS2
MS2
1: BODY ECU HARNESS
NCNC
JS7
TL2/7
JS6
!
2
2
SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.
6
5 4 3 2 1
10 9 8 7
16
28
15
27
14
26
13
25
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4 3 2 1
STEERING LOCK (C)
JS1 JS2
1: STEERING LOCK
1: STEERING LOCK HARNESS
JS5
M1
04
010102020303
0505
07070808
0606
!
M3
M1
M2 M5M4
PAGE 3 OF 8
Patent No. US 8,856,780 CA 2759622 2016-2018 Lexus LX570 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 60: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/60.jpg)
T006_W
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
A
C
B
PAGE 4 OF 8
Patent No. US 8,856,780 CA 2759622 2016-2018 Lexus LX570 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 61: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/61.jpg)
4
!
3
10 11 12 13 14 15 16 17 18
19 20 21 22 23 24 25 26 27 29 30
1 2 3 4 5 6
7 8
29
2
8 9
28
7 6 5 4 3 2 1
1
1
3
1
2
2
6
5 4 3 2 1
10 9 8 7
16
28
15
27
14
26
13
25
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4 3 2 1
T006_W
1
2
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
HARDWIRE / WIRING DIAGRAM - 1 OF 1
1
1
PTS (-) BLUE - 01
M5
M4
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
03 BROWN/RED - CANH 103 BROWN/RED - CANH 104 BROWN/YELLOW - CANL 104 BROWN/YELLOW - CANL 1
1: WHITE
2: WHITE
MAIN BODY ECU, DRIVER SIDE DASH (B)
STEERING LOCK (C)
CANH (DATA) GREEN - 14
CANL (DATA) WHITE - 13
AUTOLIGHT (-) PINK - 08
LOCK (-) GREEN - 29
UNLOCK (-) PINK - 02
PTS SWITCH (A)
06 BLUE/WHITE•BLACK DOT06 BLUE/WHITE•BLACK DOT
08 WHITE/PURPLE•BLACK DOT
01 GREEN•BLACK DOT - LOCK (-) OUTPUT01 GREEN•BLACK DOT - LOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT
07 EMPTY07 EMPTY
09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT12 WHITE•BLACK DOT12 WHITE•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01 EMPTY01 EMPTY02 EMPTY02 EMPTY
05 BLUE/RED05 BLUE/RED06 BLUE/YELLOW06 BLUE/YELLOW07 EMPTY07 EMPTY08 ORANGE08 ORANGE09 YELLOW09 YELLOW10 EMPTY10 EMPTY11 GRAY/RED11 GRAY/RED12 GRAY/YELLOW12 GRAY/YELLOW13 GREEN/RED - SLP (-) OUTPUT13 GREEN/RED - SLP (-) OUTPUT14 ORANGE/WHITE14 ORANGE/WHITE15 BROWN15 BROWN16 ORANGE/BLACK - GROUND (-) INPUT16 ORANGE/BLACK - GROUND (-) INPUT17 PINK - IGNITION (+) IN/OUT17 PINK - IGNITION (+) IN/OUT18 PURPLE18 PURPLE19 RED - 12V (+) INPUT19 RED - 12V (+) INPUT20 BLACK - GROUND (-)20 BLACK - GROUND (-)
01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE03 GRAY/RED•BLUE DOT03 GRAY/RED•BLUE DOT04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE05 GRAY•BLUE DOT - GROUND (-) INPUT05 GRAY•BLUE DOT - GROUND (-) INPUT06 WHITE•BLUE DOT06 WHITE•BLUE DOT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
HORN (-)
TRUNK (-) BLACK - 05
SLP (-) RED - 04
IGNITION (+) PINK - 06
12V (+) GREEN - 07
HOOD SWITCH
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
WITHOUT OEM HOOD STATUS ONLY
CONNECTION REQUIRED ONLY IF IDLE MODE IS DESIREDM1
04 PINK/WHITE
01 ORANGE01 ORANGE02 RED02 RED03 PURPLE03 PURPLE
05 PINK05 PINK
07 RED07 RED08 BLACK08 BLACK
06 WHITE06 WHITE
!
M3
M1
M2 M5M4
PAGE 5 OF 8
Patent No. US 8,856,780 CA 2759622 2016-2018 Lexus LX570 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 62: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/62.jpg)
01
ENGINE
START
STOP
STOP ACC ON STARTON
02
03
ENGINE
START
STOP
STOP ACC ON STARTSTOP
04
05
ENGINE
START
STOP
STOP ACC ON STARTON
06
07
ENGINE
START
STOP
STOP ACC ON STARTSTOP
08
ENGINE
START
STOP
STOP ACC ON STARTSTART
09
10
11
12
13
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Push start button twice [2x] to ON position.
Wait, if LED 1 turns solid GREEN for 2 seconds, proceed to step 7. If LED 1 flashes GREEN rapidly, proceed to step 3.
Push start button once [1x] to OFF position.
Wait, LED 1 will turn solid RED. (This may take up to 5 minutes.)
Push start button twice [2x] to ON position.
Wait, LED 1 will turn solid GREEN for 2 seconds.
Push start button once [1x] to OFF position.
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming button.
Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
PAGE 6 OF 8
Patent No. US 8,856,780 CA 2759622 2016-2018 Lexus LX570 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 63: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/63.jpg)
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
4 Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
11 Open hood.
12If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
PAGE 7 OF 8
Patent No. US 8,856,780 CA 2759622 2016-2018 Lexus LX570 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 64: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/64.jpg)
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
PAGE 8 OF 8
Patent No. US 8,856,780 CA 2759622 2016-2018 Lexus LX570 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 65: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/65.jpg)
Patent No. US 8,856,780 CA 2759622
20181121
REVISION DATE
ADS-RSA-TL7-[HC2352AC]
FIRMWARE
HC2352AC
HARDWARE
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED.
VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
ACCESSORIES
DOCUMENT NUMBER
2015-2017 LEXUS NX200T PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2018
INSTALL GUIDE
TERMS OF USEAutomotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users.
![Page 66: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/66.jpg)
T002_H
T-HARNESS / COMPONENT LOCATOR - 1 OF 1
A
B
C
PAGE 2 OF 8
Patent No. US 8,856,780 CA 2759622 2015-2017 Lexus NX200T PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 67: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/67.jpg)
4
5
3
T002_H
1
3
4
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
NOT REQUIRED FOR BASIC INSTALLATION.INSERT WIRE TERMINALS IN MS3 CONNECTOR FOR OPTIONAL OUTPUTS.REFER TO PRODUCT GUIDE FOR MORE INFORMATION.
T-HARNESS / WIRING DIAGRAM - 1 OF 1
2: WHITE
1
1: BODY ECU
M5
M4
M2
M3
0404
03030404
PTS SWITCH (A)
MAIN BODY ECU, DRIVER SIDE DASH (B)
0606
08
010102020303
0505
0707
0909
11111212
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01010202
050506060707080809091010
121213131414151516161717181819192020
0101
04040505
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
1010
HOOD SWITCH
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CONNECT IF VEHICLE IS NOTEQUIPPED WITH OEM HOOD PIN
POWER LIFTGATE (-) RED - 05
PTS (-) GREEN - 01
CONNECTION REQUIRED IF IDLE MODE IS DESIRED.
03030202
0606
1111
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
JS4
MS3
MS1
VS3
VS4
JS8
TL6
RED/WHITE•BLACK DOT - TRUNK (-) OUTPUTRED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
GREEN/BLACK•BLACK DOTGREEN/BLACK•BLACK DOTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUT
PURPLEPURPLE
VS1
VS2
MS2
1: BODY ECU HARNESS
NCNC
JS7
TL2/7
JS6
!
2
2
SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.
6
5 4 3 2 1
10 9 8 7
16
28
15
27
14
26
13
25
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4 3 2 1
STEERING LOCK (C)
JS1 JS2
1: STEERING LOCK
1: STEERING LOCK HARNESS
JS5
1 2
M1
04
010102020303
0505
07070808
0606
!
M3
M1
M2 M5M4
PAGE 3 OF 8
Patent No. US 8,856,780 CA 2759622 2015-2017 Lexus NX200T PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 68: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/68.jpg)
T002_W
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
A
B
C
PAGE 4 OF 8
Patent No. US 8,856,780 CA 2759622 2015-2017 Lexus NX200T PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 69: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/69.jpg)
4
!
10 11 12 13 14 15 16 17 18
19 20 21 22 23 24 25 26 27 29 30
1 2 3 4 5 6
7 8
29
2
8 9
28
7 6 5 4 3 2 1
1
1
1
6
5 4 3 2 1
10 9 8 7
T002_W
3
3
2
2
16
28
15
27
14
26
13
25
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4 3 2 1
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
HARDWIRE / WIRING DIAGRAM - 1 OF 1
1
1
PTS (-) GREEN - 01
M5
M4
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
03 BROWN/RED - CANH 103 BROWN/RED - CANH 104 BROWN/YELLOW - CANL 104 BROWN/YELLOW - CANL 1
1: WHITE
2: WHITE
MAIN BODY ECU, BELOW DASH FUSEBOX (B)
STEERING LOCK (C)
CANH (DATA) YELLOW - 14
CANL (DATA) WHITE - 13
PTS SWITCH (A)
06 BLUE/WHITE•BLACK DOT06 BLUE/WHITE•BLACK DOT
08 WHITE/PURPLE•BLACK DOT
01 GREEN•BLACK DOT - LOCK (-) OUTPUT01 GREEN•BLACK DOT - LOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT
07 EMPTY07 EMPTY
09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT12 WHITE•BLACK DOT12 WHITE•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01 EMPTY01 EMPTY02 EMPTY02 EMPTY
05 BLUE/RED05 BLUE/RED06 BLUE/YELLOW06 BLUE/YELLOW07 EMPTY07 EMPTY08 ORANGE08 ORANGE09 YELLOW09 YELLOW10 EMPTY10 EMPTY11 GRAY/RED11 GRAY/RED12 GRAY/YELLOW12 GRAY/YELLOW13 GREEN/RED - SLP (-) OUTPUT13 GREEN/RED - SLP (-) OUTPUT14 ORANGE/WHITE14 ORANGE/WHITE15 BROWN15 BROWN16 ORANGE/BLACK - GROUND (-) INPUT16 ORANGE/BLACK - GROUND (-) INPUT17 PINK - IGNITION (+) IN/OUT17 PINK - IGNITION (+) IN/OUT18 PURPLE18 PURPLE19 RED - 12V (+) INPUT19 RED - 12V (+) INPUT20 BLACK - GROUND (-)20 BLACK - GROUND (-)
01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE03 GRAY/RED•BLUE DOT03 GRAY/RED•BLUE DOT04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE05 GRAY•BLUE DOT - GROUND (-) INPUT05 GRAY•BLUE DOT - GROUND (-) INPUT06 WHITE•BLUE DOT06 WHITE•BLUE DOT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
HORN (-)
SLP (-) YELLOW - 04
IGNITION (+) PINK - 06
12V (+) BLUE - 07
HOOD SWITCH
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
WITHOUT OEM HOOD STATUS ONLY
CONNECTION REQUIRED ONLY IF IDLE MODE IS DESIRED
03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
POWER LIFTGATE (-) RED - 05
AUTOLIGHT (-) GREEN - 08
LOCK (-) RED - 29
UNLOCK (-) LTGREEN - 02
1 2
M1
04 PINK/WHITE
01 ORANGE01 ORANGE02 RED02 RED03 PURPLE03 PURPLE
05 PINK05 PINK
07 RED07 RED08 BLACK08 BLACK
06 WHITE06 WHITE
!
M3
M1
M2 M5M4
PAGE 5 OF 8
Patent No. US 8,856,780 CA 2759622 2015-2017 Lexus NX200T PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 70: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/70.jpg)
01
ENGINE
START
STOP
STOP ACC ON STARTON
02
03
ENGINE
START
STOP
STOP ACC ON STARTSTOP
04
05
ENGINE
START
STOP
STOP ACC ON STARTON
06
07
ENGINE
START
STOP
STOP ACC ON STARTSTOP
08
ENGINE
START
STOP
STOP ACC ON STARTSTART
09
10
11
12
13
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Push start button twice [2x] to ON position.
Wait, if LED 1 turns solid GREEN for 2 seconds, proceed to step 7. If LED 1 flashes GREEN rapidly, proceed to step 3.
Push start button once [1x] to OFF position.
Wait, LED 1 will turn solid RED. (This may take up to 5 minutes.)
Push start button twice [2x] to ON position.
Wait, LED 1 will turn solid GREEN for 2 seconds.
Push start button once [1x] to OFF position.
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming button.
Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
PAGE 6 OF 8
Patent No. US 8,856,780 CA 2759622 2015-2017 Lexus NX200T PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 71: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/71.jpg)
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
4 Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
11 Open hood.
12If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
PAGE 7 OF 8
Patent No. US 8,856,780 CA 2759622 2015-2017 Lexus NX200T PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 72: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/72.jpg)
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
PAGE 8 OF 8
Patent No. US 8,856,780 CA 2759622 2015-2017 Lexus NX200T PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 73: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/73.jpg)
Patent No. US 8,856,780 CA 2759622
20181121
REVISION DATE
ADS-RSA-TL7-[HC2352AC]
FIRMWARE
HC2352AC
HARDWARE
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED.
VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
ACCESSORIES
DOCUMENT NUMBER
2018-2019 LEXUS NX300 PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2018
INSTALL GUIDE
TERMS OF USEAutomotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users.
![Page 74: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/74.jpg)
T002_H
T-HARNESS / COMPONENT LOCATOR - 1 OF 1
A
B
C
PAGE 2 OF 8
Patent No. US 8,856,780 CA 2759622 2018-2019 Lexus NX300 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 75: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/75.jpg)
4
5
3
T002_H
1
3
4
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
NOT REQUIRED FOR BASIC INSTALLATION.INSERT WIRE TERMINALS IN MS3 CONNECTOR FOR OPTIONAL OUTPUTS.REFER TO PRODUCT GUIDE FOR MORE INFORMATION.
T-HARNESS / WIRING DIAGRAM - 1 OF 1
2: WHITE
1
1: BODY ECU
M5
M4
M2
M3
0404
03030404
PTS SWITCH (A)
MAIN BODY ECU, DRIVER SIDE DASH (B)
0606
08
010102020303
0505
0707
0909
11111212
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01010202
050506060707080809091010
121213131414151516161717181819192020
0101
04040505
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
1010
HOOD SWITCH
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CONNECT IF VEHICLE IS NOTEQUIPPED WITH OEM HOOD PIN
POWER LIFTGATE (-) RED - 05
PTS (-) GREEN - 01
CONNECTION REQUIRED IF IDLE MODE IS DESIRED.
03030202
0606
1111
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
JS4
MS3
MS1
VS3
VS4
JS8
TL6
RED/WHITE•BLACK DOT - TRUNK (-) OUTPUTRED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
GREEN/BLACK•BLACK DOTGREEN/BLACK•BLACK DOTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUT
PURPLEPURPLE
VS1
VS2
MS2
1: BODY ECU HARNESS
NCNC
JS7
TL2/7
JS6
!
2
2
SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.
6
5 4 3 2 1
10 9 8 7
16
28
15
27
14
26
13
25
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4 3 2 1
STEERING LOCK (C)
JS1 JS2
1: STEERING LOCK
1: STEERING LOCK HARNESS
JS5
1 2
M1
04
010102020303
0505
07070808
0606
!
M3
M1
M2 M5M4
PAGE 3 OF 8
Patent No. US 8,856,780 CA 2759622 2018-2019 Lexus NX300 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 76: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/76.jpg)
T002_W
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
A
B
C
PAGE 4 OF 8
Patent No. US 8,856,780 CA 2759622 2018-2019 Lexus NX300 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 77: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/77.jpg)
4
!
10 11 12 13 14 15 16 17 18
19 20 21 22 23 24 25 26 27 29 30
1 2 3 4 5 6
7 8
29
2
8 9
28
7 6 5 4 3 2 1
1
1
1
6
5 4 3 2 1
10 9 8 7
T002_W
3
3
2
2
16
28
15
27
14
26
13
25
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4 3 2 1
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
HARDWIRE / WIRING DIAGRAM - 1 OF 1
1
1
PTS (-) GREEN - 01
M5
M4
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
03 BROWN/RED - CANH 103 BROWN/RED - CANH 104 BROWN/YELLOW - CANL 104 BROWN/YELLOW - CANL 1
1: WHITE
2: WHITE
MAIN BODY ECU, BELOW DASH FUSEBOX (B)
STEERING LOCK (C)
CANH (DATA) YELLOW - 14
CANL (DATA) WHITE - 13
PTS SWITCH (A)
06 BLUE/WHITE•BLACK DOT06 BLUE/WHITE•BLACK DOT
08 WHITE/PURPLE•BLACK DOT
01 GREEN•BLACK DOT - LOCK (-) OUTPUT01 GREEN•BLACK DOT - LOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT
07 EMPTY07 EMPTY
09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT12 WHITE•BLACK DOT12 WHITE•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01 EMPTY01 EMPTY02 EMPTY02 EMPTY
05 BLUE/RED05 BLUE/RED06 BLUE/YELLOW06 BLUE/YELLOW07 EMPTY07 EMPTY08 ORANGE08 ORANGE09 YELLOW09 YELLOW10 EMPTY10 EMPTY11 GRAY/RED11 GRAY/RED12 GRAY/YELLOW12 GRAY/YELLOW13 GREEN/RED - SLP (-) OUTPUT13 GREEN/RED - SLP (-) OUTPUT14 ORANGE/WHITE14 ORANGE/WHITE15 BROWN15 BROWN16 ORANGE/BLACK - GROUND (-) INPUT16 ORANGE/BLACK - GROUND (-) INPUT17 PINK - IGNITION (+) IN/OUT17 PINK - IGNITION (+) IN/OUT18 PURPLE18 PURPLE19 RED - 12V (+) INPUT19 RED - 12V (+) INPUT20 BLACK - GROUND (-)20 BLACK - GROUND (-)
01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE03 GRAY/RED•BLUE DOT03 GRAY/RED•BLUE DOT04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE05 GRAY•BLUE DOT - GROUND (-) INPUT05 GRAY•BLUE DOT - GROUND (-) INPUT06 WHITE•BLUE DOT06 WHITE•BLUE DOT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
HORN (-)
SLP (-) YELLOW - 04
IGNITION (+) PINK - 06
12V (+) BLUE - 07
HOOD SWITCH
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
WITHOUT OEM HOOD STATUS ONLY
CONNECTION REQUIRED ONLY IF IDLE MODE IS DESIRED
03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
POWER LIFTGATE (-) RED - 05
AUTOLIGHT (-) GREEN - 08
LOCK (-) RED - 29
UNLOCK (-) LTGREEN - 02
1 2
M1
04 PINK/WHITE
01 ORANGE01 ORANGE02 RED02 RED03 PURPLE03 PURPLE
05 PINK05 PINK
07 RED07 RED08 BLACK08 BLACK
06 WHITE06 WHITE
!
M3
M1
M2 M5M4
PAGE 5 OF 8
Patent No. US 8,856,780 CA 2759622 2018-2019 Lexus NX300 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 78: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/78.jpg)
01
ENGINE
START
STOP
STOP ACC ON STARTON
02
03
ENGINE
START
STOP
STOP ACC ON STARTSTOP
04
05
ENGINE
START
STOP
STOP ACC ON STARTON
06
07
ENGINE
START
STOP
STOP ACC ON STARTSTOP
08
ENGINE
START
STOP
STOP ACC ON STARTSTART
09
10
11
12
13
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Push start button twice [2x] to ON position.
Wait, if LED 1 turns solid GREEN for 2 seconds, proceed to step 7. If LED 1 flashes GREEN rapidly, proceed to step 3.
Push start button once [1x] to OFF position.
Wait, LED 1 will turn solid RED. (This may take up to 5 minutes.)
Push start button twice [2x] to ON position.
Wait, LED 1 will turn solid GREEN for 2 seconds.
Push start button once [1x] to OFF position.
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming button.
Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
PAGE 6 OF 8
Patent No. US 8,856,780 CA 2759622 2018-2019 Lexus NX300 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 79: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/79.jpg)
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
4 Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
11 Open hood.
12If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
PAGE 7 OF 8
Patent No. US 8,856,780 CA 2759622 2018-2019 Lexus NX300 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 80: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/80.jpg)
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
PAGE 8 OF 8
Patent No. US 8,856,780 CA 2759622 2018-2019 Lexus NX300 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 81: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/81.jpg)
Patent No. US 8,856,780 CA 2759622
20181121
REVISION DATE
ADS-RSA-TL7-[HC2352AC]
FIRMWARE
HC2352AC
HARDWARE
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED.
VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
ACCESSORIES
DOCUMENT NUMBER
2017 LEXUS NX300H PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2018
INSTALL GUIDE
TERMS OF USEAutomotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users.
![Page 82: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/82.jpg)
T002_H
T-HARNESS / COMPONENT LOCATOR - 1 OF 1
A
B
C
PAGE 2 OF 8
Patent No. US 8,856,780 CA 2759622 2017 Lexus NX300h PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 83: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/83.jpg)
4
5
3
T002_H
1
3
4
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
NOT REQUIRED FOR BASIC INSTALLATION.INSERT WIRE TERMINALS IN MS3 CONNECTOR FOR OPTIONAL OUTPUTS.REFER TO PRODUCT GUIDE FOR MORE INFORMATION.
T-HARNESS / WIRING DIAGRAM - 1 OF 1
2: WHITE
1
1: BODY ECU
M5
M4
M2
M3
0404
03030404
PTS SWITCH (A)
MAIN BODY ECU, DRIVER SIDE DASH (B)
0606
08
010102020303
0505
0707
0909
11111212
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01010202
050506060707080809091010
121213131414151516161717181819192020
0101
04040505
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
1010
HOOD SWITCH
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CONNECT IF VEHICLE IS NOTEQUIPPED WITH OEM HOOD PIN
POWER LIFTGATE (-) RED - 05
PTS (-) GREEN - 01
CONNECTION REQUIRED IF IDLE MODE IS DESIRED.
03030202
0606
1111
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
JS4
MS3
MS1
VS3
VS4
JS8
TL6
RED/WHITE•BLACK DOT - TRUNK (-) OUTPUTRED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
GREEN/BLACK•BLACK DOTGREEN/BLACK•BLACK DOTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUT
PURPLEPURPLE
VS1
VS2
MS2
1: BODY ECU HARNESS
NCNC
JS7
TL2/7
JS6
!
2
2
SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.
6
5 4 3 2 1
10 9 8 7
16
28
15
27
14
26
13
25
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4 3 2 1
STEERING LOCK (C)
JS1 JS2
1: STEERING LOCK
1: STEERING LOCK HARNESS
JS5
1 2
M1
04
010102020303
0505
07070808
0606
!
M3
M1
M2 M5M4
PAGE 3 OF 8
Patent No. US 8,856,780 CA 2759622 2017 Lexus NX300h PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 84: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/84.jpg)
T002_W
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
A
B
C
PAGE 4 OF 8
Patent No. US 8,856,780 CA 2759622 2017 Lexus NX300h PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 85: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/85.jpg)
4
!
10 11 12 13 14 15 16 17 18
19 20 21 22 23 24 25 26 27 29 30
1 2 3 4 5 6
7 8
29
2
8 9
28
7 6 5 4 3 2 1
1
1
1
6
5 4 3 2 1
10 9 8 7
T002_W
3
3
2
2
16
28
15
27
14
26
13
25
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4 3 2 1
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
HARDWIRE / WIRING DIAGRAM - 1 OF 1
1
1
PTS (-) GREEN - 01
M5
M4
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
03 BROWN/RED - CANH 103 BROWN/RED - CANH 104 BROWN/YELLOW - CANL 104 BROWN/YELLOW - CANL 1
1: WHITE
2: WHITE
MAIN BODY ECU, BELOW DASH FUSEBOX (B)
STEERING LOCK (C)
CANH (DATA) YELLOW - 14
CANL (DATA) WHITE - 13
PTS SWITCH (A)
06 BLUE/WHITE•BLACK DOT06 BLUE/WHITE•BLACK DOT
08 WHITE/PURPLE•BLACK DOT
01 GREEN•BLACK DOT - LOCK (-) OUTPUT01 GREEN•BLACK DOT - LOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT
07 EMPTY07 EMPTY
09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT12 WHITE•BLACK DOT12 WHITE•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01 EMPTY01 EMPTY02 EMPTY02 EMPTY
05 BLUE/RED05 BLUE/RED06 BLUE/YELLOW06 BLUE/YELLOW07 EMPTY07 EMPTY08 ORANGE08 ORANGE09 YELLOW09 YELLOW10 EMPTY10 EMPTY11 GRAY/RED11 GRAY/RED12 GRAY/YELLOW12 GRAY/YELLOW13 GREEN/RED - SLP (-) OUTPUT13 GREEN/RED - SLP (-) OUTPUT14 ORANGE/WHITE14 ORANGE/WHITE15 BROWN15 BROWN16 ORANGE/BLACK - GROUND (-) INPUT16 ORANGE/BLACK - GROUND (-) INPUT17 PINK - IGNITION (+) IN/OUT17 PINK - IGNITION (+) IN/OUT18 PURPLE18 PURPLE19 RED - 12V (+) INPUT19 RED - 12V (+) INPUT20 BLACK - GROUND (-)20 BLACK - GROUND (-)
01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE03 GRAY/RED•BLUE DOT03 GRAY/RED•BLUE DOT04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE05 GRAY•BLUE DOT - GROUND (-) INPUT05 GRAY•BLUE DOT - GROUND (-) INPUT06 WHITE•BLUE DOT06 WHITE•BLUE DOT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
HORN (-)
SLP (-) YELLOW - 04
IGNITION (+) PINK - 06
12V (+) BLUE - 07
HOOD SWITCH
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
WITHOUT OEM HOOD STATUS ONLY
CONNECTION REQUIRED ONLY IF IDLE MODE IS DESIRED
03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
POWER LIFTGATE (-) RED - 05
AUTOLIGHT (-) GREEN - 08
LOCK (-) RED - 29
UNLOCK (-) LTGREEN - 02
1 2
M1
04 PINK/WHITE
01 ORANGE01 ORANGE02 RED02 RED03 PURPLE03 PURPLE
05 PINK05 PINK
07 RED07 RED08 BLACK08 BLACK
06 WHITE06 WHITE
!
M3
M1
M2 M5M4
PAGE 5 OF 8
Patent No. US 8,856,780 CA 2759622 2017 Lexus NX300h PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 86: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/86.jpg)
01
ENGINE
START
STOP
STOP ACC ON STARTON
02
03
ENGINE
START
STOP
STOP ACC ON STARTSTOP
04
05
ENGINE
START
STOP
STOP ACC ON STARTON
06
07
ENGINE
START
STOP
STOP ACC ON STARTSTOP
08
ENGINE
START
STOP
STOP ACC ON STARTSTART
09
10
11
12
13
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Push start button twice [2x] to ON position.
Wait, if LED 1 turns solid GREEN for 2 seconds, proceed to step 7. If LED 1 flashes GREEN rapidly, proceed to step 3.
Push start button once [1x] to OFF position.
Wait, LED 1 will turn solid RED. (This may take up to 5 minutes.)
Push start button twice [2x] to ON position.
Wait, LED 1 will turn solid GREEN for 2 seconds.
Push start button once [1x] to OFF position.
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming button.
Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
PAGE 6 OF 8
Patent No. US 8,856,780 CA 2759622 2017 Lexus NX300h PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 87: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/87.jpg)
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
4 Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
11 Open hood.
12If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
PAGE 7 OF 8
Patent No. US 8,856,780 CA 2759622 2017 Lexus NX300h PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 88: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/88.jpg)
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
PAGE 8 OF 8
Patent No. US 8,856,780 CA 2759622 2017 Lexus NX300h PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 89: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/89.jpg)
Patent No. US 8,856,780 CA 2759622
20181121
REVISION DATE
ADS-RSA-TL7-[HC2352AC]
FIRMWARE
HC2352AC
HARDWARE
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED.
VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
ACCESSORIES
DOCUMENT NUMBER
2017-2018 LEXUS RC300 PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2018
INSTALL GUIDE
TERMS OF USEAutomotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users.
![Page 90: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/90.jpg)
T006_H
T-HARNESS / COMPONENT LOCATOR - 1 OF 1
A
B
C
PAGE 2 OF 8
Patent No. US 8,856,780 CA 2759622 2017-2018 Lexus RC300 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 91: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/91.jpg)
4
5
3
1
T006_H
1
3
4
2
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
NOT REQUIRED FOR BASIC INSTALLATION.INSERT WIRE TERMINALS IN MS3 CONNECTOR FOR OPTIONAL OUTPUTS.REFER TO PRODUCT GUIDE FOR MORE INFORMATION.
T-HARNESS / WIRING DIAGRAM - 1 OF 1
2: WHITE
1
1: BODY ECU
M5
M4
M2
M3
0404
03030404
PTS SWITCH (A)
MAIN BODY ECU, DRIVER SIDE DASH (B)
0606
08
010102020303
0505
0707
0909
11111212
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01010202
050506060707080809091010
121213131414151516161717181819192020
0101
04040505
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
1010
HOOD SWITCH
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CONNECT IF VEHICLE IS NOTEQUIPPED WITH OEM HOOD PIN
POWER LIFTGATE (-) RED - 05
PTS (-) BLUE - 01
CONNECTION REQUIRED IF IDLE MODE IS DESIRED.
03030202
0606
1111
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
JS4
MS3
MS1
VS3
VS4JS8
TL6
RED/WHITE•BLACK DOT - TRUNK (-) OUTPUTRED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
GREEN/BLACK•BLACK DOTGREEN/BLACK•BLACK DOTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUT
PURPLEPURPLE
VS1
VS2
MS2
1: BODY ECU HARNESS
NCNC
JS7
TL2/7
JS6
!
2
2
SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.
6
5 4 3 2 1
10 9 8 7
16
28
15
27
14
26
13
25
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4 3 2 1
STEERING LOCK (C)
JS1 JS2
1: STEERING LOCK
1: STEERING LOCK HARNESS
JS5
M1
04
010102020303
0505
07070808
0606
!
M3
M1
M2 M5M4
PAGE 3 OF 8
Patent No. US 8,856,780 CA 2759622 2017-2018 Lexus RC300 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 92: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/92.jpg)
T006_W
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
A
C
B
PAGE 4 OF 8
Patent No. US 8,856,780 CA 2759622 2017-2018 Lexus RC300 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 93: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/93.jpg)
4
!
3
10 11 12 13 14 15 16 17 18
19 20 21 22 23 24 25 26 27 29 30
1 2 3 4 5 6
7 8
29
2
8 9
28
7 6 5 4 3 2 1
1
1
3
1
2
2
6
5 4 3 2 1
10 9 8 7
16
28
15
27
14
26
13
25
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4 3 2 1
T006_W
1
2
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
HARDWIRE / WIRING DIAGRAM - 1 OF 1
1
1
PTS (-) BLUE - 01
M5
M4
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
03 BROWN/RED - CANH 103 BROWN/RED - CANH 104 BROWN/YELLOW - CANL 104 BROWN/YELLOW - CANL 1
1: WHITE
2: WHITE
MAIN BODY ECU, DRIVER SIDE DASH (B)
STEERING LOCK (C)
CANH (DATA) GREEN - 14
CANL (DATA) WHITE - 13
AUTOLIGHT (-) PINK - 08
LOCK (-) GREEN - 29
UNLOCK (-) PINK - 02
PTS SWITCH (A)
06 BLUE/WHITE•BLACK DOT06 BLUE/WHITE•BLACK DOT
08 WHITE/PURPLE•BLACK DOT
01 GREEN•BLACK DOT - LOCK (-) OUTPUT01 GREEN•BLACK DOT - LOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT
07 EMPTY07 EMPTY
09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT12 WHITE•BLACK DOT12 WHITE•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01 EMPTY01 EMPTY02 EMPTY02 EMPTY
05 BLUE/RED05 BLUE/RED06 BLUE/YELLOW06 BLUE/YELLOW07 EMPTY07 EMPTY08 ORANGE08 ORANGE09 YELLOW09 YELLOW10 EMPTY10 EMPTY11 GRAY/RED11 GRAY/RED12 GRAY/YELLOW12 GRAY/YELLOW13 GREEN/RED - SLP (-) OUTPUT13 GREEN/RED - SLP (-) OUTPUT14 ORANGE/WHITE14 ORANGE/WHITE15 BROWN15 BROWN16 ORANGE/BLACK - GROUND (-) INPUT16 ORANGE/BLACK - GROUND (-) INPUT17 PINK - IGNITION (+) IN/OUT17 PINK - IGNITION (+) IN/OUT18 PURPLE18 PURPLE19 RED - 12V (+) INPUT19 RED - 12V (+) INPUT20 BLACK - GROUND (-)20 BLACK - GROUND (-)
01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE03 GRAY/RED•BLUE DOT03 GRAY/RED•BLUE DOT04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE05 GRAY•BLUE DOT - GROUND (-) INPUT05 GRAY•BLUE DOT - GROUND (-) INPUT06 WHITE•BLUE DOT06 WHITE•BLUE DOT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
HORN (-)
TRUNK (-) BLACK - 05
SLP (-) RED - 04
IGNITION (+) PINK - 06
12V (+) GREEN - 07
HOOD SWITCH
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
WITHOUT OEM HOOD STATUS ONLY
CONNECTION REQUIRED ONLY IF IDLE MODE IS DESIREDM1
04 PINK/WHITE
01 ORANGE01 ORANGE02 RED02 RED03 PURPLE03 PURPLE
05 PINK05 PINK
07 RED07 RED08 BLACK08 BLACK
06 WHITE06 WHITE
!
M3
M1
M2 M5M4
PAGE 5 OF 8
Patent No. US 8,856,780 CA 2759622 2017-2018 Lexus RC300 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 94: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/94.jpg)
01
ENGINE
START
STOP
STOP ACC ON STARTON
02
03
ENGINE
START
STOP
STOP ACC ON STARTSTOP
04
05
ENGINE
START
STOP
STOP ACC ON STARTON
06
07
ENGINE
START
STOP
STOP ACC ON STARTSTOP
08
ENGINE
START
STOP
STOP ACC ON STARTSTART
09
10
11
12
13
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Push start button twice [2x] to ON position.
Wait, if LED 1 turns solid GREEN for 2 seconds, proceed to step 7. If LED 1 flashes GREEN rapidly, proceed to step 3.
Push start button once [1x] to OFF position.
Wait, LED 1 will turn solid RED. (This may take up to 5 minutes.)
Push start button twice [2x] to ON position.
Wait, LED 1 will turn solid GREEN for 2 seconds.
Push start button once [1x] to OFF position.
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming button.
Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
PAGE 6 OF 8
Patent No. US 8,856,780 CA 2759622 2017-2018 Lexus RC300 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 95: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/95.jpg)
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
4 Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
11 Open hood.
12If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
PAGE 7 OF 8
Patent No. US 8,856,780 CA 2759622 2017-2018 Lexus RC300 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 96: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/96.jpg)
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
PAGE 8 OF 8
Patent No. US 8,856,780 CA 2759622 2017-2018 Lexus RC300 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 97: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/97.jpg)
Patent No. US 8,856,780 CA 2759622
20181121
REVISION DATE
ADS-RSA-TL7-[HC2352AC]
FIRMWARE
HC2352AC
HARDWARE
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED.
VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
ACCESSORIES
DOCUMENT NUMBER
2015-2018 LEXUS RC350 PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2018
INSTALL GUIDE
TERMS OF USEAutomotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users.
![Page 98: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/98.jpg)
T004_H
T-HARNESS / COMPONENT LOCATOR - 1 OF 1
A
BC
PAGE 2 OF 8
Patent No. US 8,856,780 CA 2759622 2015-2018 Lexus RC350 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 99: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/99.jpg)
4
5
3
1
T004_H
1
3
4
2
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
NOT REQUIRED FOR BASIC INSTALLATION.INSERT WIRE TERMINALS IN MS3 CONNECTOR FOR OPTIONAL OUTPUTS.REFER TO PRODUCT GUIDE FOR MORE INFORMATION.
T-HARNESS / WIRING DIAGRAM - 1 OF 1
2: WHITE
1
1: BODY ECU
M5
M4
M2
M3
0404
03030404
PTS SWITCH (A)
MAIN BODY ECU, DRIVER SIDE DASH (B)
0606
08
010102020303
0505
0707
0909
11111212
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01010202
050506060707080809091010
121213131414151516161717181819192020
0101
04040505
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
1010
HOOD SWITCH
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CONNECT IF VEHICLE IS NOTEQUIPPED WITH OEM HOOD PIN
TRUNK (-) PINK - 05
PTS (-) BLUE - 01
CONNECTION REQUIRED IF IDLE MODE IS DESIRED.
03030202
0606
1111
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
JS4
MS3
MS1
VS3
VS4
JS8
TL6
RED/WHITE•BLACK DOT - TRUNK (-) OUTPUTRED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
GREEN/BLACK•BLACK DOTGREEN/BLACK•BLACK DOTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUT
PURPLEPURPLE
VS1
VS2
MS2
1: BODY ECU HARNESS
NCNC
JS7
TL2/7
JS6
!
2
2
SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.
6
5 4 3 2 1
10 9 8 7
16
28
15
27
14
26
13
25
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4 3 2 1
STEERING LOCK (C)
JS1 JS2
1: STEERING LOCK
1: STEERING LOCK HARNESS
JS5
M1
04
010102020303
0505
07070808
0606
!
M3
M1
M2 M5M4
PAGE 3 OF 8
Patent No. US 8,856,780 CA 2759622 2015-2018 Lexus RC350 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 100: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/100.jpg)
T004_W
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
A
BC
PAGE 4 OF 8
Patent No. US 8,856,780 CA 2759622 2015-2018 Lexus RC350 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 101: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/101.jpg)
4
!
10 11 12 13 14 15 16 17 18
19 20 21 22 23 24 25 26 27 29 30
1 2 3 4 5 6
7 8
29
2
8 9
28
7 6 5 4 3 2 1
6
5 4 3 2 1
10 9 8 7
164
7
8
9
19
1
2
3
20
21
10
11
12
22
23
24
13
14
15
25
26
27
17
18
28
5
6
T004_W
1
1
1
3
3
2
2
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
HARDWIRE / WIRING DIAGRAM - 1 OF 1
1
1
PTS (-) BLUE - 01
M5
M4
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
03 BROWN/RED - CANH 103 BROWN/RED - CANH 104 BROWN/YELLOW - CANL 104 BROWN/YELLOW - CANL 1
1: WHITE
2: WHITE
MAIN BODY ECU, DRIVER SIDE DASH (C)
STEERING LOCK (D)
CANH (DATA) LTGREEN OR YELLOW - 14
CANL (DATA) BLACK - 13
PTS SWITCH (A)
06 BLUE/WHITE•BLACK DOT06 BLUE/WHITE•BLACK DOT
08 WHITE/PURPLE•BLACK DOT
01 GREEN•BLACK DOT - LOCK (-) OUTPUT01 GREEN•BLACK DOT - LOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT
07 EMPTY07 EMPTY
09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT12 WHITE•BLACK DOT12 WHITE•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01 EMPTY01 EMPTY02 EMPTY02 EMPTY
05 BLUE/RED05 BLUE/RED06 BLUE/YELLOW06 BLUE/YELLOW07 EMPTY07 EMPTY08 ORANGE08 ORANGE09 YELLOW09 YELLOW10 EMPTY10 EMPTY11 GRAY/RED11 GRAY/RED12 GRAY/YELLOW12 GRAY/YELLOW13 GREEN/RED - SLP (-) OUTPUT13 GREEN/RED - SLP (-) OUTPUT14 ORANGE/WHITE14 ORANGE/WHITE15 BROWN15 BROWN16 ORANGE/BLACK - GROUND (-) INPUT16 ORANGE/BLACK - GROUND (-) INPUT17 PINK - IGNITION (+) IN/OUT17 PINK - IGNITION (+) IN/OUT18 PURPLE18 PURPLE19 RED - 12V (+) INPUT19 RED - 12V (+) INPUT20 BLACK - GROUND (-)20 BLACK - GROUND (-)
01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE03 GRAY/RED•BLUE DOT03 GRAY/RED•BLUE DOT04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE05 GRAY•BLUE DOT - GROUND (-) INPUT05 GRAY•BLUE DOT - GROUND (-) INPUT06 WHITE•BLUE DOT06 WHITE•BLUE DOT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
HORN (-)
TRUNK (-) PINK - 05
SLP (-) RED - 04
IGNITION (+) BLACK - 06
12V (+) GREEN - 07
HOOD SWITCH
1
2
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
WITHOUT OEM HOOD STATUS ONLY
CONNECTION REQUIRED ONLY IF IDLE MODE IS DESIRED
AUTOLIGHT (-) PINK - 08
LOCK (-) BLUE - 29
UNLOCK (-) LTGREEN - 02
M1
04 PINK/WHITE
01 ORANGE01 ORANGE02 RED02 RED03 PURPLE03 PURPLE
05 PINK05 PINK
07 RED07 RED08 BLACK08 BLACK
06 WHITE06 WHITE
!
M3
M1
M2 M5M4
PAGE 5 OF 8
Patent No. US 8,856,780 CA 2759622 2015-2018 Lexus RC350 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 102: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/102.jpg)
01
ENGINE
START
STOP
STOP ACC ON STARTON
02
03
ENGINE
START
STOP
STOP ACC ON STARTSTOP
04
05
ENGINE
START
STOP
STOP ACC ON STARTON
06
07
ENGINE
START
STOP
STOP ACC ON STARTSTOP
08
ENGINE
START
STOP
STOP ACC ON STARTSTART
09
10
11
12
13
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Push start button twice [2x] to ON position.
Wait, if LED 1 turns solid GREEN for 2 seconds, proceed to step 7. If LED 1 flashes GREEN rapidly, proceed to step 3.
Push start button once [1x] to OFF position.
Wait, LED 1 will turn solid RED. (This may take up to 5 minutes.)
Push start button twice [2x] to ON position.
Wait, LED 1 will turn solid GREEN for 2 seconds.
Push start button once [1x] to OFF position.
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming button.
Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
PAGE 6 OF 8
Patent No. US 8,856,780 CA 2759622 2015-2018 Lexus RC350 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 103: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/103.jpg)
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
4 Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
11 Open hood.
12If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
PAGE 7 OF 8
Patent No. US 8,856,780 CA 2759622 2015-2018 Lexus RC350 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 104: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/104.jpg)
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
PAGE 8 OF 8
Patent No. US 8,856,780 CA 2759622 2015-2018 Lexus RC350 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 105: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/105.jpg)
Patent No. US 8,856,780 CA 2759622
20181121
REVISION DATE
ADS-RSA-TL7-[HC2352AC]
FIRMWARE
HC2352AC
HARDWARE
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED.
VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
ACCESSORIES
DOCUMENT NUMBER
2016-2018 LEXUS RX350 PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2018
INSTALL GUIDE
TERMS OF USEAutomotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users.
![Page 106: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/106.jpg)
T007_H
T-HARNESS / COMPONENT LOCATOR - 1 OF 1
A
B
C
PAGE 2 OF 8
Patent No. US 8,856,780 CA 2759622 2016-2018 Lexus RX350 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 107: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/107.jpg)
4
5
3
1
T007_H
1
3
4
2
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
NOT REQUIRED FOR BASIC INSTALLATION.INSERT WIRE TERMINALS IN MS3 CONNECTOR FOR OPTIONAL OUTPUTS.REFER TO PRODUCT GUIDE FOR MORE INFORMATION.
T-HARNESS / WIRING DIAGRAM - 1 OF 1
2: WHITE
1
1: BODY ECU
M5
M4
M2
M3
0404
03030404
PTS SWITCH (A)
MAIN BODY ECU, DRIVER SIDE DASH (B)
0606
08
010102020303
0505
0707
0909
11111212
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01010202
050506060707080809091010
121213131414151516161717181819192020
0101
04040505
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
1010
HOOD SWITCH
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CONNECT IF VEHICLE IS NOTEQUIPPED WITH OEM HOOD PIN
TRUNK (-) RED - 05
PTS (-) BLUE - 01
CONNECTION REQUIRED IF IDLE MODE IS DESIRED.
03030202
0606
1111
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
JS4
MS3
MS1
VS3
VS4
JS8
TL6
RED/WHITE•BLACK DOT - TRUNK (-) OUTPUTRED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
GREEN/BLACK•BLACK DOTGREEN/BLACK•BLACK DOTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUT
PURPLEPURPLE
VS1
VS2
MS2
1: BODY ECU HARNESS
NCNC
JS7
TL2/7
JS6
!
2
2
SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.
6
5 4 3 2 1
10 9 8 7
16
28
15
27
14
26
13
25
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4 3 2 1
STEERING LOCK (C)
JS1 JS2
1: STEERING LOCK
1: STEERING LOCK HARNESS
JS5
M1
04
010102020303
0505
07070808
0606
!
M3
M1
M2 M5M4
PAGE 3 OF 8
Patent No. US 8,856,780 CA 2759622 2016-2018 Lexus RX350 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 108: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/108.jpg)
T007_W
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
A
CB
PAGE 4 OF 8
Patent No. US 8,856,780 CA 2759622 2016-2018 Lexus RX350 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 109: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/109.jpg)
4
!
3
10 11 12 13 14 15 16 17 18
19 20 21 22 23 24 25 26 27 29 30
1 2 3 4 5 6
7 8
29
2
8 9
28
7 6 5 4 3 2 1
1
1
3
1
2
2
6
5 4 3 2 1
10 9 8 7
16
4
789
19
123
2021
101112
222324
131415
252627 171828
56
T007_W
1
2
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
HARDWIRE / WIRING DIAGRAM - 1 OF 1
1
1
PTS (-) PURPLE - 01
M5
M4
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
03 BROWN/RED - CANH 103 BROWN/RED - CANH 104 BROWN/YELLOW - CANL 104 BROWN/YELLOW - CANL 1
1: WHITE
2: WHITE
MAIN BODY ECU, DRIVER SIDE DASH (B)
STEERING LOCK (C)
CANH (DATA) LTBLUE - 14
CANL (DATA) WHITE - 13
AUTOLIGHT (-) GREEN - 08
LOCK (-) PINK - 29
UNLOCK (-) PURPLE - 02
PTS SWITCH (A)
06 BLUE/WHITE•BLACK DOT06 BLUE/WHITE•BLACK DOT
08 WHITE/PURPLE•BLACK DOT
01 GREEN•BLACK DOT - LOCK (-) OUTPUT01 GREEN•BLACK DOT - LOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT
07 EMPTY07 EMPTY
09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT12 WHITE•BLACK DOT12 WHITE•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01 EMPTY01 EMPTY02 EMPTY02 EMPTY
05 BLUE/RED05 BLUE/RED06 BLUE/YELLOW06 BLUE/YELLOW07 EMPTY07 EMPTY08 ORANGE08 ORANGE09 YELLOW09 YELLOW10 EMPTY10 EMPTY11 GRAY/RED11 GRAY/RED12 GRAY/YELLOW12 GRAY/YELLOW13 GREEN/RED - SLP (-) OUTPUT13 GREEN/RED - SLP (-) OUTPUT14 ORANGE/WHITE14 ORANGE/WHITE15 BROWN15 BROWN16 ORANGE/BLACK - GROUND (-) INPUT16 ORANGE/BLACK - GROUND (-) INPUT17 PINK - IGNITION (+) IN/OUT17 PINK - IGNITION (+) IN/OUT18 PURPLE18 PURPLE19 RED - 12V (+) INPUT19 RED - 12V (+) INPUT20 BLACK - GROUND (-)20 BLACK - GROUND (-)
01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE03 GRAY/RED•BLUE DOT03 GRAY/RED•BLUE DOT04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE05 GRAY•BLUE DOT - GROUND (-) INPUT05 GRAY•BLUE DOT - GROUND (-) INPUT06 WHITE•BLUE DOT06 WHITE•BLUE DOT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
HORN (-)
TRUNK (-) RED - 05
SLP (-) GRAY - 04
IGNITION (+) PINK - 06
12V (+) PURPLE - 07
HOOD SWITCH
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
WITHOUT OEM HOOD STATUS ONLY
CONNECTION REQUIRED ONLY IF IDLE MODE IS DESIREDM1
04 PINK/WHITE
01 ORANGE01 ORANGE02 RED02 RED03 PURPLE03 PURPLE
05 PINK05 PINK
07 RED07 RED08 BLACK08 BLACK
06 WHITE06 WHITE
!
M3
M1
M2 M5M4
PAGE 5 OF 8
Patent No. US 8,856,780 CA 2759622 2016-2018 Lexus RX350 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 110: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/110.jpg)
01
ENGINE
START
STOP
STOP ACC ON STARTON
02
03
ENGINE
START
STOP
STOP ACC ON STARTSTOP
04
05
ENGINE
START
STOP
STOP ACC ON STARTON
06
07
ENGINE
START
STOP
STOP ACC ON STARTSTOP
08
ENGINE
START
STOP
STOP ACC ON STARTSTART
09
10
11
12
13
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Push start button twice [2x] to ON position.
Wait, if LED 1 turns solid GREEN for 2 seconds, proceed to step 7. If LED 1 flashes GREEN rapidly, proceed to step 3.
Push start button once [1x] to OFF position.
Wait, LED 1 will turn solid RED. (This may take up to 5 minutes.)
Push start button twice [2x] to ON position.
Wait, LED 1 will turn solid GREEN for 2 seconds.
Push start button once [1x] to OFF position.
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming button.
Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
PAGE 6 OF 8
Patent No. US 8,856,780 CA 2759622 2016-2018 Lexus RX350 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 111: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/111.jpg)
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
4 Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
11 Open hood.
12If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
PAGE 7 OF 8
Patent No. US 8,856,780 CA 2759622 2016-2018 Lexus RX350 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 112: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/112.jpg)
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
PAGE 8 OF 8
Patent No. US 8,856,780 CA 2759622 2016-2018 Lexus RX350 PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 113: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/113.jpg)
Patent No. US 8,856,780 CA 2759622
20181121
REVISION DATE
ADS-RSA-TL7-[HC2352AC]
FIRMWARE
HC2352AC
HARDWARE
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED.
VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
ACCESSORIES
DOCUMENT NUMBER
2016-2018 LEXUS RX450H PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2018
INSTALL GUIDE
TERMS OF USEAutomotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users.
![Page 114: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/114.jpg)
T014_H
T-HARNESS / COMPONENT LOCATOR - 1 OF 1
A
B
C
D
PAGE 2 OF 8
Patent No. US 8,856,780 CA 2759622 2016-2018 Lexus RX450h PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 115: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/115.jpg)
4
5
3
1
T014_H
1
3
4
2
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
NOT REQUIRED FOR BASIC INSTALLATION.INSERT WIRE TERMINALS IN MS3 CONNECTOR FOR OPTIONAL OUTPUTS.REFER TO PRODUCT GUIDE FOR MORE INFORMATION.
T-HARNESS / WIRING DIAGRAM - 1 OF 1
2: WHITE
1
1: BODY ECU
M5
M4
M2
M3
0404
03030404
PTS SWITCH (A)
MAIN BODY ECU, DRIVER SIDE DASH (B)
0606
08
010102020303
0505
0707
0909
11111212
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01010202
050506060707080809091010
121213131414151516161717181819192020
0101
04040505
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
1010
HOOD SWITCH
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CONNECT IF VEHICLE IS NOTEQUIPPED WITH OEM HOOD PIN
TRUNK (-) RED - 05
PTS (-) BLUE - 01
CONNECTION REQUIRED IF IDLE MODE IS DESIRED.
03030202
0606
1111
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
JS4
MS3
MS1
VS3
VS4
JS8
TL6
RED/WHITE•BLACK DOT - TRUNK (-) OUTPUTRED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
GREEN/BLACK•BLACK DOTGREEN/BLACK•BLACK DOTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUT
PURPLE - STARTER (+) OUTPUTPURPLE - STARTER (+) OUTPUT
VS1
VS2
MS2
1: BODY ECU HARNESS
NCNC
JS7
TL2/7
JS6
!
2
2
SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.
6
5 4 3 2 1
10 9 8 7
16
28
15
27
14
26
13
25
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4 3 2 1
STEERING LOCK (C)
JS1 JS2
1: STEERING LOCK
1: STEERING LOCK HARNESS
JS5
STARTER (+) LtGREEN - 27
1: WHITE
CERTIFICATION ECU, BEHIND GLOVEBOX (D)
1
1
5
1821222324 1920252627
67891011121314151617
234
M1
04
010102020303
0505
07070808
0606
!
M3
M1
M2 M5M4
PAGE 3 OF 8
Patent No. US 8,856,780 CA 2759622 2016-2018 Lexus RX450h PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 116: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/116.jpg)
T014_W
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
A
CB D
PAGE 4 OF 8
Patent No. US 8,856,780 CA 2759622 2016-2018 Lexus RX450h PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 117: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/117.jpg)
4
!
3
10 11 12 13 14 15 16 17 18
19 20 21 22 23 24 25 26 27 29 30
1 2 3 4 5 6
7 8
29
2
8 9
28
7 6 5 4 3 2 1
1
1
3
1
2
2
6
5 4 3 2 1
10 9 8 7
16
4
789
19
123
2021
101112
222324
131415
252627 171828
56
T014_W
1
2
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
HARDWIRE / WIRING DIAGRAM - 1 OF 1
1
1
PTS (-) PURPLE - 01
M5
M4
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
03 BROWN/RED - CANH 103 BROWN/RED - CANH 104 BROWN/YELLOW - CANL 104 BROWN/YELLOW - CANL 1
1: WHITE
2: WHITE
MAIN BODY ECU, DRIVER SIDE DASH (B)
STEERING LOCK (C)
CANH (DATA) LTBLUE - 14
CANL (DATA) WHITE - 13
AUTOLIGHT (-) GREEN - 08
LOCK (-) PINK - 29
UNLOCK (-) PURPLE - 02
PTS SWITCH (A)
06 BLUE/WHITE•BLACK DOT06 BLUE/WHITE•BLACK DOT
08 WHITE/PURPLE•BLACK DOT
01 GREEN•BLACK DOT - LOCK (-) OUTPUT01 GREEN•BLACK DOT - LOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT
07 EMPTY07 EMPTY
09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT12 WHITE•BLACK DOT12 WHITE•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01 EMPTY01 EMPTY02 EMPTY02 EMPTY
05 BLUE/RED05 BLUE/RED06 BLUE/YELLOW06 BLUE/YELLOW07 EMPTY07 EMPTY08 ORANGE08 ORANGE09 YELLOW09 YELLOW10 EMPTY10 EMPTY11 GRAY/RED11 GRAY/RED12 GRAY/YELLOW12 GRAY/YELLOW13 GREEN/RED - SLP (-) OUTPUT13 GREEN/RED - SLP (-) OUTPUT14 ORANGE/WHITE14 ORANGE/WHITE15 BROWN15 BROWN16 ORANGE/BLACK - GROUND (-) INPUT16 ORANGE/BLACK - GROUND (-) INPUT17 PINK - IGNITION (+) IN/OUT17 PINK - IGNITION (+) IN/OUT18 PURPLE - STARTER (+) OUTPUT18 PURPLE - STARTER (+) OUTPUT19 RED - 12V (+) INPUT19 RED - 12V (+) INPUT20 BLACK - GROUND (-)20 BLACK - GROUND (-)
01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE03 GRAY/RED•BLUE DOT03 GRAY/RED•BLUE DOT04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE05 GRAY•BLUE DOT - GROUND (-) INPUT05 GRAY•BLUE DOT - GROUND (-) INPUT06 WHITE•BLUE DOT06 WHITE•BLUE DOT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
HORN (-)
TRUNK (-) RED - 05
SLP (-) GRAY - 04
IGNITION (+) PINK - 06
12V (+) PURPLE - 07
HOOD SWITCH
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
WITHOUT OEM HOOD STATUS ONLY
CONNECTION REQUIRED ONLY IF IDLE MODE IS DESIRED
STARTER (+) LtGREEN - 27
1: WHITE
CERTIFICATION ECU, BEHIND GLOVEBOX (D)
1
1
5
1821222324 1920252627
67891011121314151617
234
M1
04 PINK/WHITE
01 ORANGE01 ORANGE02 RED02 RED03 PURPLE03 PURPLE
05 PINK05 PINK
07 RED07 RED08 BLACK08 BLACK
06 WHITE06 WHITE
!
M3
M1
M2 M5M4
PAGE 5 OF 8
Patent No. US 8,856,780 CA 2759622 2016-2018 Lexus RX450h PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 118: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/118.jpg)
01
ENGINE
START
STOP
STOP ACC ON STARTON
02
03
ENGINE
START
STOP
STOP ACC ON STARTSTOP
04
05
ENGINE
START
STOP
STOP ACC ON STARTON
06
07
ENGINE
START
STOP
STOP ACC ON STARTSTOP
08
ENGINE
START
STOP
STOP ACC ON STARTSTART
09
10
11
12
13
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Push start button twice [2x] to ON position.
Wait, if LED 1 turns solid GREEN for 2 seconds, proceed to step 7. If LED 1 flashes GREEN rapidly, proceed to step 3.
Push start button once [1x] to OFF position.
Wait, LED 1 will turn solid RED. (This may take up to 5 minutes.)
Push start button twice [2x] to ON position.
Wait, LED 1 will turn solid GREEN for 2 seconds.
Push start button once [1x] to OFF position.
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming button.
Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
PAGE 6 OF 8
Patent No. US 8,856,780 CA 2759622 2016-2018 Lexus RX450h PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 119: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/119.jpg)
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
4 Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
11 Open hood.
12If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
PAGE 7 OF 8
Patent No. US 8,856,780 CA 2759622 2016-2018 Lexus RX450h PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 120: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/120.jpg)
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
PAGE 8 OF 8
Patent No. US 8,856,780 CA 2759622 2016-2018 Lexus RX450h PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 121: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/121.jpg)
Patent No. US 8,856,780 CA 2759622
20181121
REVISION DATE
ADS-RSA-TL7-[HC2352AC]
FIRMWARE
HC2352AC
HARDWARE
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED.
VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
ACCESSORIES
DOCUMENT NUMBER
2018-2019 TOYOTA C-HR PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2018
INSTALL GUIDE
TERMS OF USEAutomotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users.
![Page 122: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/122.jpg)
T011_H
T-HARNESS / COMPONENT LOCATOR - 1 OF 1
A
B
C
PAGE 2 OF 8
Patent No. US 8,856,780 CA 2759622 2018-2019 Toyota C-HR PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 123: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/123.jpg)
4
5
3
1
T011_H
1
3
4
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
NOT REQUIRED FOR BASIC INSTALLATION.INSERT WIRE TERMINALS IN MS3 CONNECTOR FOR OPTIONAL OUTPUTS.REFER TO PRODUCT GUIDE FOR MORE INFORMATION.
T-HARNESS / WIRING DIAGRAM - 1 OF 1
1
1: BODY ECU
M5
M4
M2
M3
0404
03030404
PTS SWITCH (A)
MAIN BODY ECU, DRIVER SIDE DASH (B)
0606
08
010102020303
0505
0707
0909
11111212
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01010202
050506060707080809091010
121213131414151516161717181819192020
0101
04040505
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
1010
HOOD SWITCH
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CONNECT IF VEHICLE IS NOTEQUIPPED WITH OEM HOOD PIN
PTS (-) GRAY - 01
CONNECTION REQUIRED IF IDLE MODE IS DESIRED.
03030202
0606
1111
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
JS4
MS3
MS1
VS3
VS4
JS8
TL6
RED/WHITE•BLACK DOTRED/WHITE•BLACK DOT
GREEN/BLACK•BLACK DOTGREEN/BLACK•BLACK DOTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUT
PURPLEPURPLE
VS1
VS2
MS2
1: BODY ECU HARNESS
NCNC
JS7
TL2/7
JS6
!
2
2
SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.
6
5 4 3 2 1
10 9 8 7
STEERING LOCK (C)
JS1 JS2
1: STEERING LOCK
1: STEERING LOCK HARNESS
JS5
M1
04
010102020303
0505
07070808
0606
!
M3
M1
M2 M5M4
PAGE 3 OF 8
Patent No. US 8,856,780 CA 2759622 2018-2019 Toyota C-HR PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 124: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/124.jpg)
T011_W
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
A
B
C
PAGE 4 OF 8
Patent No. US 8,856,780 CA 2759622 2018-2019 Toyota C-HR PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 125: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/125.jpg)
4
!
10 11 12 13 14 15 16 17 18
19 20 21 22 23 24 25 26 27 29 30
1 2 3 4 5 6
7 8
29
2
8 9
28
7 6 5 4 3 2 1
6
5 4 3 2 1
10 9 8 7
T011_W
1
1
1
3
3
2
2
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
HARDWIRE / WIRING DIAGRAM - 1 OF 1
1
1
PTS (-) GRAY - 01
M5
M4
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
03 BROWN/RED - CANH 103 BROWN/RED - CANH 104 BROWN/YELLOW - CANL 104 BROWN/YELLOW - CANL 1
1: WHITE
MAIN BODY ECU, BELOW DASH FUSEBOX (B)
STEERING LOCK (C)
CANH (DATA) GREEN - 14
CANL (DATA) LTBLUE - 13
PTS SWITCH (A)
06 BLUE/WHITE•BLACK DOT06 BLUE/WHITE•BLACK DOT
08 WHITE/PURPLE•BLACK DOT
01 GREEN•BLACK DOT - LOCK (-) OUTPUT01 GREEN•BLACK DOT - LOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT03 RED/WHITE•BLACK DOT03 RED/WHITE•BLACK DOT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT
07 EMPTY07 EMPTY
09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT12 WHITE•BLACK DOT12 WHITE•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01 EMPTY01 EMPTY02 EMPTY02 EMPTY
05 BLUE/RED05 BLUE/RED06 BLUE/YELLOW06 BLUE/YELLOW07 EMPTY07 EMPTY08 ORANGE08 ORANGE09 YELLOW09 YELLOW10 EMPTY10 EMPTY11 GRAY/RED11 GRAY/RED12 GRAY/YELLOW12 GRAY/YELLOW13 GREEN/RED - SLP (-) OUTPUT13 GREEN/RED - SLP (-) OUTPUT14 ORANGE/WHITE14 ORANGE/WHITE15 BROWN15 BROWN16 ORANGE/BLACK - GROUND (-) INPUT16 ORANGE/BLACK - GROUND (-) INPUT17 PINK - IGNITION (+) IN/OUT17 PINK - IGNITION (+) IN/OUT18 PURPLE18 PURPLE19 RED - 12V (+) INPUT19 RED - 12V (+) INPUT20 BLACK - GROUND (-)20 BLACK - GROUND (-)
01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE03 GRAY/RED•BLUE DOT03 GRAY/RED•BLUE DOT04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE05 GRAY•BLUE DOT - GROUND (-) INPUT05 GRAY•BLUE DOT - GROUND (-) INPUT06 WHITE•BLUE DOT06 WHITE•BLUE DOT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
HORN (-)
SLP (-) GREEN - 04
IGNITION (+) BLACK - 06
12V (+) BLUE - 07
HOOD SWITCH
1
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE.
WITHOUT OEM HOOD STATUS ONLY
CONNECTION REQUIRED ONLY IF IDLE MODE IS DESIRED
AUTOLIGHT (-) WHITE - 08
LOCK (-) GREEN - 29
UNLOCK (-) BLUE - 02
M1
04 PINK/WHITE
01 ORANGE01 ORANGE02 RED02 RED03 PURPLE03 PURPLE
05 PINK05 PINK
07 RED07 RED08 BLACK08 BLACK
06 WHITE06 WHITE
!
M3
M1
M2 M5M4
PAGE 5 OF 8
Patent No. US 8,856,780 CA 2759622 2018-2019 Toyota C-HR PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 126: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/126.jpg)
01
ENGINE
START
STOP
STOP ACC ON STARTON
02
03
ENGINE
START
STOP
STOP ACC ON STARTSTOP
04
05
ENGINE
START
STOP
STOP ACC ON STARTON
06
07
ENGINE
START
STOP
STOP ACC ON STARTSTOP
08
ENGINE
START
STOP
STOP ACC ON STARTSTART
09
10
11
12
13
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Push start button twice [2x] to ON position.
Wait, if LED 1 turns solid GREEN for 2 seconds, proceed to step 7. If LED 1 flashes GREEN rapidly, proceed to step 3.
Push start button once [1x] to OFF position.
Wait, LED 1 will turn solid RED. (This may take up to 5 minutes.)
Push start button twice [2x] to ON position.
Wait, LED 1 will turn solid GREEN for 2 seconds.
Push start button once [1x] to OFF position.
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming button.
Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
PAGE 6 OF 8
Patent No. US 8,856,780 CA 2759622 2018-2019 Toyota C-HR PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 127: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/127.jpg)
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
4 Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
11 Open hood.
12If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
PAGE 7 OF 8
Patent No. US 8,856,780 CA 2759622 2018-2019 Toyota C-HR PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 128: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/128.jpg)
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
PAGE 8 OF 8
Patent No. US 8,856,780 CA 2759622 2018-2019 Toyota C-HR PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 129: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/129.jpg)
Patent No. US 8,856,780 CA 2759622
20181121
REVISION DATE
ADS-RSA-TL7-[HC2352AC]
FIRMWARE
HC2352AC
HARDWARE
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED.
VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
ACCESSORIES
DOCUMENT NUMBER
2018 TOYOTA CAMRY HYBRID PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2018
INSTALL GUIDE
TERMS OF USEAutomotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users.
![Page 130: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/130.jpg)
T013_W
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
A
B
E
CD
PAGE 2 OF 6
Patent No. US 8,856,780 CA 2759622 2018 Toyota Camry Hybrid PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 131: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/131.jpg)
4
!
7 6 5 4 3 2 1
6
5 4 3 2 1
10 9 8 7
T013_W
1
1
1
3
3
2
2
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
HARDWIRE / WIRING DIAGRAM - 1 OF 1
1: BLACK
1: BLACK
PTS (-) GRAY - 01
M5
M4
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
03 BROWN/RED - CANH 103 BROWN/RED - CANH 104 BROWN/YELLOW - CANL 104 BROWN/YELLOW - CANL 1
1: BLACK (K52)
2: BLACK (K53)
MAIN BODY ECU/DASH FUSEBOX (B)
STEERING LOCK (C)
HEADLAMP SWITCH (D)
CANH (DATA) TAN - 05
CANL (DATA) WHITE - 04
PTS SWITCH (A)
06 BLUE/WHITE•BLACK DOT06 BLUE/WHITE•BLACK DOT
08 WHITE/PURPLE•BLACK DOT
01 GREEN•BLACK DOT - LOCK (-) OUTPUT01 GREEN•BLACK DOT - LOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT
07 EMPTY07 EMPTY
09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT12 WHITE•BLACK DOT12 WHITE•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01 EMPTY01 EMPTY02 EMPTY02 EMPTY
05 BLUE/RED05 BLUE/RED06 BLUE/YELLOW06 BLUE/YELLOW07 EMPTY07 EMPTY08 ORANGE08 ORANGE09 YELLOW09 YELLOW10 EMPTY10 EMPTY11 GRAY/RED11 GRAY/RED12 GRAY/YELLOW12 GRAY/YELLOW13 GREEN/RED - SLP (-) OUTPUT13 GREEN/RED - SLP (-) OUTPUT14 ORANGE/WHITE14 ORANGE/WHITE15 BROWN15 BROWN16 ORANGE/BLACK - GROUND (-) INPUT16 ORANGE/BLACK - GROUND (-) INPUT17 PINK - IGNITION (+) IN/OUT17 PINK - IGNITION (+) IN/OUT18 PURPLE - STARTER (+) OUTPUT18 PURPLE - STARTER (+) OUTPUT19 RED - 12V (+) INPUT19 RED - 12V (+) INPUT20 BLACK - GROUND (-)20 BLACK - GROUND (-)
01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE03 GRAY/RED•BLUE DOT03 GRAY/RED•BLUE DOT04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE05 GRAY•BLUE DOT - GROUND (-) INPUT05 GRAY•BLUE DOT - GROUND (-) INPUT06 WHITE•BLUE DOT06 WHITE•BLUE DOT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
HORN (-)
SLP (-) TAN - 04
IGNITION (+) LTGREEN - 06
12V (+) WHITE - 07
HOOD SWITCH
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE.
WITHOUT OEM HOOD STATUS ONLY
CONNECTION REQUIRED ONLY IF IDLE MODE IS DESIRED
AUTOLIGHT (-) WHITE OR YELLOW - 05
STARTER (+) LTBLUE - 09
LOCK (-) LTGREEN - 18
UNLOCK (-) TAN - 17
TRUNK (-) LTGREEN - 04
12345678910111213141516
19202122232425262728293031323334353637383940
1718
12345
678910111213141516171819
202122282930 2324252627
12
1415161718192021
345678910111213
1
2
1: WHITE
HYBRID ECU, RIGHT OF DRIVER DASH FUSEBOX (E)
1: GRAY
123456
10111213141516
27 171819
282930
20212223242526
35 31323334
789
M1
04 PINK/WHITE
01 ORANGE01 ORANGE02 RED02 RED03 PURPLE03 PURPLE
05 PINK05 PINK
07 RED07 RED08 BLACK08 BLACK
06 WHITE06 WHITE
!
M3
M1
M2 M5M4
PAGE 3 OF 6
Patent No. US 8,856,780 CA 2759622 2018 Toyota Camry Hybrid PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 132: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/132.jpg)
01
ENGINE
START
STOP
STOP ACC ON STARTON
02
03
ENGINE
START
STOP
STOP ACC ON STARTSTOP
04
05
ENGINE
START
STOP
STOP ACC ON STARTON
06
07
ENGINE
START
STOP
STOP ACC ON STARTSTOP
08
ENGINE
START
STOP
STOP ACC ON STARTSTART
09
10
11
12
13
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Push start button twice [2x] to ON position.
Wait, if LED 1 turns solid GREEN for 2 seconds, proceed to step 7. If LED 1 flashes GREEN rapidly, proceed to step 3.
Push start button once [1x] to OFF position.
Wait, LED 1 will turn solid RED. (This may take up to 5 minutes.)
Push start button twice [2x] to ON position.
Wait, LED 1 will turn solid GREEN for 2 seconds.
Push start button once [1x] to OFF position.
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming button.
Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
PAGE 4 OF 6
Patent No. US 8,856,780 CA 2759622 2018 Toyota Camry Hybrid PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 133: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/133.jpg)
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
4 Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
11 Open hood.
12If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
PAGE 5 OF 6
Patent No. US 8,856,780 CA 2759622 2018 Toyota Camry Hybrid PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 134: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/134.jpg)
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
PAGE 6 OF 6
Patent No. US 8,856,780 CA 2759622 2018 Toyota Camry Hybrid PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 135: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/135.jpg)
Patent No. US 8,856,780 CA 2759622
20181121
REVISION DATE
ADS-RSA-TL7-[HC2352AC]
FIRMWARE
HC2352AC
HARDWARE
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED.
VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
ACCESSORIES
DOCUMENT NUMBER
2018 TOYOTA CAMRY PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2018
INSTALL GUIDE
TERMS OF USEAutomotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users.
![Page 136: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/136.jpg)
T012_W
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
A
B
CD
PAGE 2 OF 6
Patent No. US 8,856,780 CA 2759622 2018 Toyota Camry PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 137: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/137.jpg)
4
!
7 6 5 4 3 2 1
6
5 4 3 2 1
10 9 8 7
T012_W
1
1
1
3
3
2
2
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
HARDWIRE / WIRING DIAGRAM - 1 OF 1
1: BLACK
1: BLACK
PTS (-) GRAY - 01
M5
M4
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
03 BROWN/RED - CANH 103 BROWN/RED - CANH 104 BROWN/YELLOW - CANL 104 BROWN/YELLOW - CANL 1
1: BLACK (K52)
2: BLACK (K53)
MAIN BODY ECU/DASH FUSEBOX (B)
STEERING LOCK (C)
HEADLAMP SWITCH (D)
CANH (DATA) TAN - 05
CANL (DATA) WHITE - 04
PTS SWITCH (A)
06 BLUE/WHITE•BLACK DOT06 BLUE/WHITE•BLACK DOT
08 WHITE/PURPLE•BLACK DOT
01 GREEN•BLACK DOT - LOCK (-) OUTPUT01 GREEN•BLACK DOT - LOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT
07 EMPTY07 EMPTY
09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT12 WHITE•BLACK DOT12 WHITE•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01 EMPTY01 EMPTY02 EMPTY02 EMPTY
05 BLUE/RED05 BLUE/RED06 BLUE/YELLOW06 BLUE/YELLOW07 EMPTY07 EMPTY08 ORANGE08 ORANGE09 YELLOW09 YELLOW10 EMPTY10 EMPTY11 GRAY/RED11 GRAY/RED12 GRAY/YELLOW12 GRAY/YELLOW13 GREEN/RED - SLP (-) OUTPUT13 GREEN/RED - SLP (-) OUTPUT14 ORANGE/WHITE14 ORANGE/WHITE15 BROWN15 BROWN16 ORANGE/BLACK - GROUND (-) INPUT16 ORANGE/BLACK - GROUND (-) INPUT17 PINK - IGNITION (+) IN/OUT17 PINK - IGNITION (+) IN/OUT18 PURPLE18 PURPLE19 RED - 12V (+) INPUT19 RED - 12V (+) INPUT20 BLACK - GROUND (-)20 BLACK - GROUND (-)
01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE03 GRAY/RED•BLUE DOT03 GRAY/RED•BLUE DOT04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE05 GRAY•BLUE DOT - GROUND (-) INPUT05 GRAY•BLUE DOT - GROUND (-) INPUT06 WHITE•BLUE DOT06 WHITE•BLUE DOT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
HORN (-)
SLP (-) TAN - 04
IGNITION (+) LTGREEN - 06
12V (+) WHITE - 07
HOOD SWITCH
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE.
WITHOUT OEM HOOD STATUS ONLY
CONNECTION REQUIRED ONLY IF IDLE MODE IS DESIRED
AUTOLIGHT (-) WHITE OR YELLOW - 05
LOCK (-) LTGREEN - 18
UNLOCK (-) TAN - 17
TRUNK (-) LTGREEN - 04
12345678910111213141516
19202122232425262728293031323334353637383940
1718
12345
678910111213141516171819
202122282930 2324252627
12
1415161718192021
345678910111213
1
2
1: WHITE
M1
04 PINK/WHITE
01 ORANGE01 ORANGE02 RED02 RED03 PURPLE03 PURPLE
05 PINK05 PINK
07 RED07 RED08 BLACK08 BLACK
06 WHITE06 WHITE
!
M3
M1
M2 M5M4
PAGE 3 OF 6
Patent No. US 8,856,780 CA 2759622 2018 Toyota Camry PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 138: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/138.jpg)
01
ENGINE
START
STOP
STOP ACC ON STARTON
02
03
ENGINE
START
STOP
STOP ACC ON STARTSTOP
04
05
ENGINE
START
STOP
STOP ACC ON STARTON
06
07
ENGINE
START
STOP
STOP ACC ON STARTSTOP
08
ENGINE
START
STOP
STOP ACC ON STARTSTART
09
10
11
12
13
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Push start button twice [2x] to ON position.
Wait, if LED 1 turns solid GREEN for 2 seconds, proceed to step 7. If LED 1 flashes GREEN rapidly, proceed to step 3.
Push start button once [1x] to OFF position.
Wait, LED 1 will turn solid RED. (This may take up to 5 minutes.)
Push start button twice [2x] to ON position.
Wait, LED 1 will turn solid GREEN for 2 seconds.
Push start button once [1x] to OFF position.
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming button.
Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
PAGE 4 OF 6
Patent No. US 8,856,780 CA 2759622 2018 Toyota Camry PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 139: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/139.jpg)
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
4 Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
11 Open hood.
12If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
PAGE 5 OF 6
Patent No. US 8,856,780 CA 2759622 2018 Toyota Camry PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 140: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/140.jpg)
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
PAGE 6 OF 6
Patent No. US 8,856,780 CA 2759622 2018 Toyota Camry PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 141: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/141.jpg)
Patent No. US 8,856,780 CA 2759622
20181121
REVISION DATE
ADS-RSA-TL7-[HC2352AC]
FIRMWARE
HC2352AC
HARDWARE
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED.
VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
ACCESSORIES
DOCUMENT NUMBER
2019 TOYOTA COROLLA HATCHBACK PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2018
INSTALL GUIDE
TERMS OF USEAutomotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users.
![Page 142: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/142.jpg)
T015_W
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
A
B
CD
PAGE 2 OF 6
Patent No. US 8,856,780 CA 2759622 2019 Toyota Corolla Hatchback PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 143: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/143.jpg)
4
!
7 6 5 4 3 2 1
T015_W
1
1
1
3
3
2
2
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
HARDWIRE / WIRING DIAGRAM - 1 OF 1
1: BLACK
1: BLACK
PTS (-) BLUE - 01
M5
M4
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
03 BROWN/RED - CANH 103 BROWN/RED - CANH 104 BROWN/YELLOW - CANL 104 BROWN/YELLOW - CANL 1
1: BLACK
2: BLACK
MAIN BODY ECU/DASH FUSEBOX (B)
STEERING LOCK (C)
HEADLAMP SWITCH (D)
CANH (DATA) TAN - 05
CANL (DATA) WHITE - 04
PTS SWITCH (A)
06 BLUE/WHITE•BLACK DOT06 BLUE/WHITE•BLACK DOT
08 WHITE/PURPLE•BLACK DOT
01 GREEN•BLACK DOT - LOCK (-) OUTPUT01 GREEN•BLACK DOT - LOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT03 RED/WHITE•BLACK DOT03 RED/WHITE•BLACK DOT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT
07 EMPTY07 EMPTY
09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT12 WHITE•BLACK DOT12 WHITE•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01 EMPTY01 EMPTY02 EMPTY02 EMPTY
05 BLUE/RED05 BLUE/RED06 BLUE/YELLOW06 BLUE/YELLOW07 EMPTY07 EMPTY08 ORANGE08 ORANGE09 YELLOW09 YELLOW10 EMPTY10 EMPTY11 GRAY/RED11 GRAY/RED12 GRAY/YELLOW12 GRAY/YELLOW13 GREEN/RED - SLP (-) OUTPUT13 GREEN/RED - SLP (-) OUTPUT14 ORANGE/WHITE14 ORANGE/WHITE15 BROWN15 BROWN16 ORANGE/BLACK - GROUND (-) INPUT16 ORANGE/BLACK - GROUND (-) INPUT17 PINK - IGNITION (+) IN/OUT17 PINK - IGNITION (+) IN/OUT18 PURPLE18 PURPLE19 RED - 12V (+) INPUT19 RED - 12V (+) INPUT20 BLACK - GROUND (-)20 BLACK - GROUND (-)
01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE03 GRAY/RED•BLUE DOT03 GRAY/RED•BLUE DOT04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE05 GRAY•BLUE DOT - GROUND (-) INPUT05 GRAY•BLUE DOT - GROUND (-) INPUT06 WHITE•BLUE DOT06 WHITE•BLUE DOT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
HORN (-)
SLP (-) RED - 04
IGNITION (+) RED - 06
12V (+) BLUE - 07
HOOD SWITCH
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE.
WITHOUT OEM HOOD STATUS ONLY
CONNECTION REQUIRED ONLY IF IDLE MODE IS DESIRED
AUTOLIGHT (-) YELLOW - 05
LOCK (-) GREEN - 18
UNLOCK (-) PURPLE - 17
12345678910111213141516
19202122232425262728293031323334353637383940
1718
12345
678910111213141516171819
202122282930 2324252627
12
1415161718192021
345678910111213
1
2
1: WHITE
1
7
2
8
3
9
4
10
5
11
6
12M1
04 PINK/WHITE
01 ORANGE01 ORANGE02 RED02 RED03 PURPLE03 PURPLE
05 PINK05 PINK
07 RED07 RED08 BLACK08 BLACK
06 WHITE06 WHITE
!
M3
M1
M2 M5M4
PAGE 3 OF 6
Patent No. US 8,856,780 CA 2759622 2019 Toyota Corolla Hatchback PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 144: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/144.jpg)
01
ENGINE
START
STOP
STOP ACC ON STARTON
02
03
ENGINE
START
STOP
STOP ACC ON STARTSTOP
04
05
ENGINE
START
STOP
STOP ACC ON STARTON
06
07
ENGINE
START
STOP
STOP ACC ON STARTSTOP
08
ENGINE
START
STOP
STOP ACC ON STARTSTART
09
10
11
12
13
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Push start button twice [2x] to ON position.
Wait, if LED 1 turns solid GREEN for 2 seconds, proceed to step 7. If LED 1 flashes GREEN rapidly, proceed to step 3.
Push start button once [1x] to OFF position.
Wait, LED 1 will turn solid RED. (This may take up to 5 minutes.)
Push start button twice [2x] to ON position.
Wait, LED 1 will turn solid GREEN for 2 seconds.
Push start button once [1x] to OFF position.
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming button.
Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
PAGE 4 OF 6
Patent No. US 8,856,780 CA 2759622 2019 Toyota Corolla Hatchback PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 145: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/145.jpg)
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
4 Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
11 Open hood.
12If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
PAGE 5 OF 6
Patent No. US 8,856,780 CA 2759622 2019 Toyota Corolla Hatchback PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 146: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/146.jpg)
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
PAGE 6 OF 6
Patent No. US 8,856,780 CA 2759622 2019 Toyota Corolla Hatchback PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 147: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/147.jpg)
Patent No. US 8,856,780 CA 2759622
20181121
REVISION DATE
ADS-RSA-TL7-[HC2352AC]
FIRMWARE
HC2352AC
HARDWARE
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED.
VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
ACCESSORIES
DOCUMENT NUMBER
2014-2016 TOYOTA HIGHLANDER HYBRID PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2018
INSTALL GUIDE
TERMS OF USEAutomotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users.
![Page 148: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/148.jpg)
T003_H
T-HARNESS / COMPONENT LOCATOR - 1 OF 1
A
B
C
PAGE 2 OF 8
Patent No. US 8,856,780 CA 2759622 2014-2016 Toyota Highlander Hybrid PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 149: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/149.jpg)
4
5
3
1
T003_H
1
3
4
2
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
NOT REQUIRED FOR BASIC INSTALLATION.INSERT WIRE TERMINALS IN MS3 CONNECTOR FOR OPTIONAL OUTPUTS.REFER TO PRODUCT GUIDE FOR MORE INFORMATION.
T-HARNESS / WIRING DIAGRAM - 1 OF 1
2: WHITE
1
1: BODY ECU
M5
M4
M2
M3
0404
03030404
PTS SWITCH (A)
MAIN BODY ECU, DRIVER SIDE DASH (B)
0606
08
010102020303
0505
0707
0909
11111212
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01010202
050506060707080809091010
121213131414151516161717181819192020
0101
04040505
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
1010
HOOD SWITCH
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CONNECT IF VEHICLE IS NOTEQUIPPED WITH OEM HOOD PIN
TRUNK (-) GRAY - 05
PTS (-) PURPLE - 01
CONNECTION REQUIRED IF IDLE MODE IS DESIRED.
03030202
0606
1111
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
JS4
MS3
MS1
VS3
VS4
JS8
TL6
RED/WHITE•BLACK DOT - TRUNK (-) OUTPUTRED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
GREEN/BLACK•BLACK DOTGREEN/BLACK•BLACK DOTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUT
PURPLEPURPLE
VS1
VS2
MS2
1: BODY ECU HARNESS
NCNC
JS7
TL2/7
JS6
!
2
2
SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.
6
5 4 3 2 1
10 9 8 7
16
28
15
27
14
26
13
25
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4 3 2 1
STEERING LOCK (C)
JS1 JS2
1: STEERING LOCK
1: STEERING LOCK HARNESS
JS5
M1
04
010102020303
0505
07070808
0606
!
M3
M1
M2 M5M4
PAGE 3 OF 8
Patent No. US 8,856,780 CA 2759622 2014-2016 Toyota Highlander Hybrid PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 150: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/150.jpg)
T003_W
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
A
B
C
D
PAGE 4 OF 8
Patent No. US 8,856,780 CA 2759622 2014-2016 Toyota Highlander Hybrid PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 151: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/151.jpg)
4
!
10 11 12 13 14 15 16
1 2 3 4 5 6
14
6 7 8
9
10 11 12 13 14 15 16 17 18
19 20 21 22 23 24 25 26 27 29 30
1 2 3 4 5 6
7 8
29
2
8 9
28
7 6 5 4 3 2 1
6
5 4 3 2 1
10 9 8 7
164
7
8
9
19
1
2
3
20
21
10
11
12
22
23
24
13
14
15
25
26
27
17
18
28
5
6
T003_W
1
1
1
3
3
2
2
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
HARDWIRE / WIRING DIAGRAM - 1 OF 1
1
1
1
PTS (-) PURPLE - 01
M5
M4
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
03 BROWN/RED - CANH 103 BROWN/RED - CANH 104 BROWN/YELLOW - CANL 104 BROWN/YELLOW - CANL 1
1: WHITE
2: WHITE
MAIN BODY ECU, DRIVER SIDE DASH (C)
STEERING LOCK (D)
CANH (DATA) PURPLE - 06
CANL (DATA) WHITE - 14
PTS SWITCH (A)
OBDII (B)
06 BLUE/WHITE•BLACK DOT06 BLUE/WHITE•BLACK DOT
08 WHITE/PURPLE•BLACK DOT
01 GREEN•BLACK DOT - LOCK (-) OUTPUT01 GREEN•BLACK DOT - LOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT
07 EMPTY07 EMPTY
09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT12 WHITE•BLACK DOT12 WHITE•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01 EMPTY01 EMPTY02 EMPTY02 EMPTY
05 BLUE/RED05 BLUE/RED06 BLUE/YELLOW06 BLUE/YELLOW07 EMPTY07 EMPTY08 ORANGE08 ORANGE09 YELLOW09 YELLOW10 EMPTY10 EMPTY11 GRAY/RED11 GRAY/RED12 GRAY/YELLOW12 GRAY/YELLOW13 GREEN/RED - SLP (-) OUTPUT13 GREEN/RED - SLP (-) OUTPUT14 ORANGE/WHITE14 ORANGE/WHITE15 BROWN15 BROWN16 ORANGE/BLACK - GROUND (-) INPUT16 ORANGE/BLACK - GROUND (-) INPUT17 PINK - IGNITION (+) IN/OUT17 PINK - IGNITION (+) IN/OUT18 PURPLE18 PURPLE19 RED - 12V (+) INPUT19 RED - 12V (+) INPUT20 BLACK - GROUND (-)20 BLACK - GROUND (-)
01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE03 GRAY/RED•BLUE DOT03 GRAY/RED•BLUE DOT04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE05 GRAY•BLUE DOT - GROUND (-) INPUT05 GRAY•BLUE DOT - GROUND (-) INPUT06 WHITE•BLUE DOT06 WHITE•BLUE DOT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
HORN (-)
TRUNK (-) GRAY - 05
SLP (-) LTGREEN - 04
IGNITION (+) RED - 06
12V (+) BLACK - 07
HOOD SWITCH
1
2
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
WITHOUT OEM HOOD STATUS ONLY
CONNECTION REQUIRED ONLY IF IDLE MODE IS DESIRED
AUTOLIGHT (-) BLACK - 08
LOCK (-) PURPLE - 29
UNLOCK (-) LTBLUE - 02
M1
04 PINK/WHITE
01 ORANGE01 ORANGE02 RED02 RED03 PURPLE03 PURPLE
05 PINK05 PINK
07 RED07 RED08 BLACK08 BLACK
06 WHITE06 WHITE
!
M3
M1
M2 M5M4
PAGE 5 OF 8
Patent No. US 8,856,780 CA 2759622 2014-2016 Toyota Highlander Hybrid PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 152: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/152.jpg)
01
ENGINE
START
STOP
STOP ACC ON STARTON
02
03
ENGINE
START
STOP
STOP ACC ON STARTSTOP
04
05
ENGINE
START
STOP
STOP ACC ON STARTON
06
07
ENGINE
START
STOP
STOP ACC ON STARTSTOP
08
ENGINE
START
STOP
STOP ACC ON STARTSTART
09
10
11
12
13
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Push start button twice [2x] to ON position.
Wait, if LED 1 turns solid GREEN for 2 seconds, proceed to step 7. If LED 1 flashes GREEN rapidly, proceed to step 3.
Push start button once [1x] to OFF position.
Wait, LED 1 will turn solid RED. (This may take up to 5 minutes.)
Push start button twice [2x] to ON position.
Wait, LED 1 will turn solid GREEN for 2 seconds.
Push start button once [1x] to OFF position.
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming button.
Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
PAGE 6 OF 8
Patent No. US 8,856,780 CA 2759622 2014-2016 Toyota Highlander Hybrid PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 153: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/153.jpg)
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
4 Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
11 Open hood.
12If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
PAGE 7 OF 8
Patent No. US 8,856,780 CA 2759622 2014-2016 Toyota Highlander Hybrid PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 154: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/154.jpg)
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
PAGE 8 OF 8
Patent No. US 8,856,780 CA 2759622 2014-2016 Toyota Highlander Hybrid PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 155: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/155.jpg)
Patent No. US 8,856,780 CA 2759622
20181121
REVISION DATE
ADS-RSA-TL7-[HC2352AC]
FIRMWARE
HC2352AC
HARDWARE
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED.
VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
ACCESSORIES
DOCUMENT NUMBER
2017-2019 TOYOTA HIGHLANDER HYBRID PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2018
INSTALL GUIDE
TERMS OF USEAutomotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users.
![Page 156: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/156.jpg)
T009_H
T-HARNESS / COMPONENT LOCATOR - 1 OF 1
A
BC
PAGE 2 OF 8
Patent No. US 8,856,780 CA 2759622 2017-2019 Toyota Highlander Hybrid PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 157: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/157.jpg)
4
5
3
1
T009_H
1
3
4
2
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
NOT REQUIRED FOR BASIC INSTALLATION.INSERT WIRE TERMINALS IN MS3 CONNECTOR FOR OPTIONAL OUTPUTS.REFER TO PRODUCT GUIDE FOR MORE INFORMATION.
T-HARNESS / WIRING DIAGRAM - 1 OF 1
2: WHITE
1
1: BODY ECU
M5
M4
M2
M3
0404
03030404
PTS SWITCH (A)
MAIN BODY ECU, DRIVER SIDE DASH (B)
0606
08
010102020303
0505
0707
0909
11111212
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01010202
050506060707080809091010
121213131414151516161717181819192020
0101
04040505
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
1010
HOOD SWITCH
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CONNECT IF VEHICLE IS NOTEQUIPPED WITH OEM HOOD PIN
TRUNK (-) GRAY - 05
PTS (-) PURPLE - 01
CONNECTION REQUIRED IF IDLE MODE IS DESIRED.
03030202
0606
1111
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
JS4
MS3
MS1
VS3
VS4
JS8
TL6
RED/WHITE•BLACK DOT - TRUNK (-) OUTPUTRED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
GREEN/BLACK•BLACK DOTGREEN/BLACK•BLACK DOTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUT
PURPLEPURPLE
VS1
VS2
MS2
1: BODY ECU HARNESS
NCNC
JS7
TL2/7
JS6
!
2
2
SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.
6
5 4 3 2 1
10 9 8 7
16
28
15
27
14
26
13
25
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4 3 2 1
STEERING LOCK (C)
JS1 JS2
1: STEERING LOCK
1: STEERING LOCK HARNESS
JS5
M1
04
010102020303
0505
07070808
0606
!
M3
M1
M2 M5M4
PAGE 3 OF 8
Patent No. US 8,856,780 CA 2759622 2017-2019 Toyota Highlander Hybrid PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 158: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/158.jpg)
T009_W
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
A
B
C
PAGE 4 OF 8
Patent No. US 8,856,780 CA 2759622 2017-2019 Toyota Highlander Hybrid PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 159: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/159.jpg)
4
!
10 11 12 13 14 15 16 17 18
19 20 21 22 23 24 25 26 27 29 30
1 2 3 4 5 6
7 8
29
2
8 9
28
7 6 5 4 3 2 1
6
5 4 3 2 1
10 9 8 7
164
7
8
9
19
1
2
3
20
21
10
11
12
22
23
24
13
14
15
25
26
27
17
18
28
5
6
T009_W
1
1
1
3
3
2
2
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
HARDWIRE / WIRING DIAGRAM - 1 OF 1
1
1
PTS (-) PURPLE - 01
M5
M4
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
03 BROWN/RED - CANH 103 BROWN/RED - CANH 104 BROWN/YELLOW - CANL 104 BROWN/YELLOW - CANL 1
1: WHITE
2: WHITE
MAIN BODY ECU, DRIVER SIDE DASH (B)
STEERING LOCK (C)
CANH (DATA) RED - 14
CANL (DATA) WHITE - 13
PTS SWITCH (A)
06 BLUE/WHITE•BLACK DOT06 BLUE/WHITE•BLACK DOT
08 WHITE/PURPLE•BLACK DOT
01 GREEN•BLACK DOT - LOCK (-) OUTPUT01 GREEN•BLACK DOT - LOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT
07 EMPTY07 EMPTY
09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT12 WHITE•BLACK DOT12 WHITE•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01 EMPTY01 EMPTY02 EMPTY02 EMPTY
05 BLUE/RED05 BLUE/RED06 BLUE/YELLOW06 BLUE/YELLOW07 EMPTY07 EMPTY08 ORANGE08 ORANGE09 YELLOW09 YELLOW10 EMPTY10 EMPTY11 GRAY/RED11 GRAY/RED12 GRAY/YELLOW12 GRAY/YELLOW13 GREEN/RED - SLP (-) OUTPUT13 GREEN/RED - SLP (-) OUTPUT14 ORANGE/WHITE14 ORANGE/WHITE15 BROWN15 BROWN16 ORANGE/BLACK - GROUND (-) INPUT16 ORANGE/BLACK - GROUND (-) INPUT17 PINK - IGNITION (+) IN/OUT17 PINK - IGNITION (+) IN/OUT18 PURPLE18 PURPLE19 RED - 12V (+) INPUT19 RED - 12V (+) INPUT20 BLACK - GROUND (-)20 BLACK - GROUND (-)
01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE03 GRAY/RED•BLUE DOT03 GRAY/RED•BLUE DOT04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE05 GRAY•BLUE DOT - GROUND (-) INPUT05 GRAY•BLUE DOT - GROUND (-) INPUT06 WHITE•BLUE DOT06 WHITE•BLUE DOT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
HORN (-)
TRUNK (-) GRAY - 05
SLP (-) LTGREEN - 04
IGNITION (+) RED - 06
12V (+) BLACK - 07
HOOD SWITCH
1
2
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE.
WITHOUT OEM HOOD STATUS ONLY
CONNECTION REQUIRED ONLY IF IDLE MODE IS DESIRED
AUTOLIGHT (-) BLACK - 08
LOCK (-) PURPLE - 29
UNLOCK (-) LTBLUE - 02
M1
04 PINK/WHITE
01 ORANGE01 ORANGE02 RED02 RED03 PURPLE03 PURPLE
05 PINK05 PINK
07 RED07 RED08 BLACK08 BLACK
06 WHITE06 WHITE
!
M3
M1
M2 M5M4
PAGE 5 OF 8
Patent No. US 8,856,780 CA 2759622 2017-2019 Toyota Highlander Hybrid PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 160: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/160.jpg)
01
ENGINE
START
STOP
STOP ACC ON STARTON
02
03
ENGINE
START
STOP
STOP ACC ON STARTSTOP
04
05
ENGINE
START
STOP
STOP ACC ON STARTON
06
07
ENGINE
START
STOP
STOP ACC ON STARTSTOP
08
ENGINE
START
STOP
STOP ACC ON STARTSTART
09
10
11
12
13
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Push start button twice [2x] to ON position.
Wait, if LED 1 turns solid GREEN for 2 seconds, proceed to step 7. If LED 1 flashes GREEN rapidly, proceed to step 3.
Push start button once [1x] to OFF position.
Wait, LED 1 will turn solid RED. (This may take up to 5 minutes.)
Push start button twice [2x] to ON position.
Wait, LED 1 will turn solid GREEN for 2 seconds.
Push start button once [1x] to OFF position.
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming button.
Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
PAGE 6 OF 8
Patent No. US 8,856,780 CA 2759622 2017-2019 Toyota Highlander Hybrid PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 161: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/161.jpg)
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
4 Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
11 Open hood.
12If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
PAGE 7 OF 8
Patent No. US 8,856,780 CA 2759622 2017-2019 Toyota Highlander Hybrid PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 162: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/162.jpg)
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
PAGE 8 OF 8
Patent No. US 8,856,780 CA 2759622 2017-2019 Toyota Highlander Hybrid PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 163: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/163.jpg)
Patent No. US 8,856,780 CA 2759622
20181121
REVISION DATE
ADS-RSA-TL7-[HC2352AC]
FIRMWARE
HC2352AC
HARDWARE
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED.
VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
ACCESSORIES
DOCUMENT NUMBER
2014-2016 TOYOTA HIGHLANDER PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2018
INSTALL GUIDE
TERMS OF USEAutomotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users.
![Page 164: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/164.jpg)
T003_H
T-HARNESS / COMPONENT LOCATOR - 1 OF 1
A
B
C
PAGE 2 OF 8
Patent No. US 8,856,780 CA 2759622 2014-2016 Toyota Highlander PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 165: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/165.jpg)
4
5
3
1
T003_H
1
3
4
2
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
NOT REQUIRED FOR BASIC INSTALLATION.INSERT WIRE TERMINALS IN MS3 CONNECTOR FOR OPTIONAL OUTPUTS.REFER TO PRODUCT GUIDE FOR MORE INFORMATION.
T-HARNESS / WIRING DIAGRAM - 1 OF 1
2: WHITE
1
1: BODY ECU
M5
M4
M2
M3
0404
03030404
PTS SWITCH (A)
MAIN BODY ECU, DRIVER SIDE DASH (B)
0606
08
010102020303
0505
0707
0909
11111212
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01010202
050506060707080809091010
121213131414151516161717181819192020
0101
04040505
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
1010
HOOD SWITCH
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CONNECT IF VEHICLE IS NOTEQUIPPED WITH OEM HOOD PIN
TRUNK (-) GRAY - 05
PTS (-) PURPLE - 01
CONNECTION REQUIRED IF IDLE MODE IS DESIRED.
03030202
0606
1111
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
JS4
MS3
MS1
VS3
VS4
JS8
TL6
RED/WHITE•BLACK DOT - TRUNK (-) OUTPUTRED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
GREEN/BLACK•BLACK DOTGREEN/BLACK•BLACK DOTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUT
PURPLEPURPLE
VS1
VS2
MS2
1: BODY ECU HARNESS
NCNC
JS7
TL2/7
JS6
!
2
2
SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.
6
5 4 3 2 1
10 9 8 7
16
28
15
27
14
26
13
25
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4 3 2 1
STEERING LOCK (C)
JS1 JS2
1: STEERING LOCK
1: STEERING LOCK HARNESS
JS5
M1
04
010102020303
0505
07070808
0606
!
M3
M1
M2 M5M4
PAGE 3 OF 8
Patent No. US 8,856,780 CA 2759622 2014-2016 Toyota Highlander PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 166: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/166.jpg)
T003_W
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
A
B
C
D
PAGE 4 OF 8
Patent No. US 8,856,780 CA 2759622 2014-2016 Toyota Highlander PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 167: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/167.jpg)
4
!
10 11 12 13 14 15 16
1 2 3 4 5 6
14
6 7 8
9
10 11 12 13 14 15 16 17 18
19 20 21 22 23 24 25 26 27 29 30
1 2 3 4 5 6
7 8
29
2
8 9
28
7 6 5 4 3 2 1
6
5 4 3 2 1
10 9 8 7
164
7
8
9
19
1
2
3
20
21
10
11
12
22
23
24
13
14
15
25
26
27
17
18
28
5
6
T003_W
1
1
1
3
3
2
2
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
HARDWIRE / WIRING DIAGRAM - 1 OF 1
1
1
1
PTS (-) PURPLE - 01
M5
M4
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
03 BROWN/RED - CANH 103 BROWN/RED - CANH 104 BROWN/YELLOW - CANL 104 BROWN/YELLOW - CANL 1
1: WHITE
2: WHITE
MAIN BODY ECU, DRIVER SIDE DASH (C)
STEERING LOCK (D)
CANH (DATA) PURPLE - 06
CANL (DATA) WHITE - 14
PTS SWITCH (A)
OBDII (B)
06 BLUE/WHITE•BLACK DOT06 BLUE/WHITE•BLACK DOT
08 WHITE/PURPLE•BLACK DOT
01 GREEN•BLACK DOT - LOCK (-) OUTPUT01 GREEN•BLACK DOT - LOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT
07 EMPTY07 EMPTY
09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT12 WHITE•BLACK DOT12 WHITE•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01 EMPTY01 EMPTY02 EMPTY02 EMPTY
05 BLUE/RED05 BLUE/RED06 BLUE/YELLOW06 BLUE/YELLOW07 EMPTY07 EMPTY08 ORANGE08 ORANGE09 YELLOW09 YELLOW10 EMPTY10 EMPTY11 GRAY/RED11 GRAY/RED12 GRAY/YELLOW12 GRAY/YELLOW13 GREEN/RED - SLP (-) OUTPUT13 GREEN/RED - SLP (-) OUTPUT14 ORANGE/WHITE14 ORANGE/WHITE15 BROWN15 BROWN16 ORANGE/BLACK - GROUND (-) INPUT16 ORANGE/BLACK - GROUND (-) INPUT17 PINK - IGNITION (+) IN/OUT17 PINK - IGNITION (+) IN/OUT18 PURPLE18 PURPLE19 RED - 12V (+) INPUT19 RED - 12V (+) INPUT20 BLACK - GROUND (-)20 BLACK - GROUND (-)
01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE03 GRAY/RED•BLUE DOT03 GRAY/RED•BLUE DOT04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE05 GRAY•BLUE DOT - GROUND (-) INPUT05 GRAY•BLUE DOT - GROUND (-) INPUT06 WHITE•BLUE DOT06 WHITE•BLUE DOT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
HORN (-)
TRUNK (-) GRAY - 05
SLP (-) LTGREEN - 04
IGNITION (+) RED - 06
12V (+) BLACK - 07
HOOD SWITCH
1
2
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
WITHOUT OEM HOOD STATUS ONLY
CONNECTION REQUIRED ONLY IF IDLE MODE IS DESIRED
AUTOLIGHT (-) BLACK - 08
LOCK (-) PURPLE - 29
UNLOCK (-) LTBLUE - 02
M1
04 PINK/WHITE
01 ORANGE01 ORANGE02 RED02 RED03 PURPLE03 PURPLE
05 PINK05 PINK
07 RED07 RED08 BLACK08 BLACK
06 WHITE06 WHITE
!
M3
M1
M2 M5M4
PAGE 5 OF 8
Patent No. US 8,856,780 CA 2759622 2014-2016 Toyota Highlander PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 168: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/168.jpg)
01
ENGINE
START
STOP
STOP ACC ON STARTON
02
03
ENGINE
START
STOP
STOP ACC ON STARTSTOP
04
05
ENGINE
START
STOP
STOP ACC ON STARTON
06
07
ENGINE
START
STOP
STOP ACC ON STARTSTOP
08
ENGINE
START
STOP
STOP ACC ON STARTSTART
09
10
11
12
13
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Push start button twice [2x] to ON position.
Wait, if LED 1 turns solid GREEN for 2 seconds, proceed to step 7. If LED 1 flashes GREEN rapidly, proceed to step 3.
Push start button once [1x] to OFF position.
Wait, LED 1 will turn solid RED. (This may take up to 5 minutes.)
Push start button twice [2x] to ON position.
Wait, LED 1 will turn solid GREEN for 2 seconds.
Push start button once [1x] to OFF position.
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming button.
Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
PAGE 6 OF 8
Patent No. US 8,856,780 CA 2759622 2014-2016 Toyota Highlander PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 169: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/169.jpg)
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
4 Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
11 Open hood.
12If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
PAGE 7 OF 8
Patent No. US 8,856,780 CA 2759622 2014-2016 Toyota Highlander PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 170: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/170.jpg)
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
PAGE 8 OF 8
Patent No. US 8,856,780 CA 2759622 2014-2016 Toyota Highlander PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 171: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/171.jpg)
Patent No. US 8,856,780 CA 2759622
20181121
REVISION DATE
ADS-RSA-TL7-[HC2352AC]
FIRMWARE
HC2352AC
HARDWARE
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED.
VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
ACCESSORIES
DOCUMENT NUMBER
2017-2019 TOYOTA HIGHLANDER PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2018
INSTALL GUIDE
TERMS OF USEAutomotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users.
![Page 172: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/172.jpg)
T009_H
T-HARNESS / COMPONENT LOCATOR - 1 OF 1
A
BC
PAGE 2 OF 8
Patent No. US 8,856,780 CA 2759622 2017-2019 Toyota Highlander PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 173: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/173.jpg)
4
5
3
1
T009_H
1
3
4
2
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
NOT REQUIRED FOR BASIC INSTALLATION.INSERT WIRE TERMINALS IN MS3 CONNECTOR FOR OPTIONAL OUTPUTS.REFER TO PRODUCT GUIDE FOR MORE INFORMATION.
T-HARNESS / WIRING DIAGRAM - 1 OF 1
2: WHITE
1
1: BODY ECU
M5
M4
M2
M3
0404
03030404
PTS SWITCH (A)
MAIN BODY ECU, DRIVER SIDE DASH (B)
0606
08
010102020303
0505
0707
0909
11111212
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01010202
050506060707080809091010
121213131414151516161717181819192020
0101
04040505
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
1010
HOOD SWITCH
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CONNECT IF VEHICLE IS NOTEQUIPPED WITH OEM HOOD PIN
TRUNK (-) GRAY - 05
PTS (-) PURPLE - 01
CONNECTION REQUIRED IF IDLE MODE IS DESIRED.
03030202
0606
1111
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
JS4
MS3
MS1
VS3
VS4
JS8
TL6
RED/WHITE•BLACK DOT - TRUNK (-) OUTPUTRED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
GREEN/BLACK•BLACK DOTGREEN/BLACK•BLACK DOTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUT
PURPLEPURPLE
VS1
VS2
MS2
1: BODY ECU HARNESS
NCNC
JS7
TL2/7
JS6
!
2
2
SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.
6
5 4 3 2 1
10 9 8 7
16
28
15
27
14
26
13
25
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4 3 2 1
STEERING LOCK (C)
JS1 JS2
1: STEERING LOCK
1: STEERING LOCK HARNESS
JS5
M1
04
010102020303
0505
07070808
0606
!
M3
M1
M2 M5M4
PAGE 3 OF 8
Patent No. US 8,856,780 CA 2759622 2017-2019 Toyota Highlander PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 174: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/174.jpg)
T009_W
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
A
B
C
PAGE 4 OF 8
Patent No. US 8,856,780 CA 2759622 2017-2019 Toyota Highlander PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 175: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/175.jpg)
4
!
10 11 12 13 14 15 16 17 18
19 20 21 22 23 24 25 26 27 29 30
1 2 3 4 5 6
7 8
29
2
8 9
28
7 6 5 4 3 2 1
6
5 4 3 2 1
10 9 8 7
164
7
8
9
19
1
2
3
20
21
10
11
12
22
23
24
13
14
15
25
26
27
17
18
28
5
6
T009_W
1
1
1
3
3
2
2
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
HARDWIRE / WIRING DIAGRAM - 1 OF 1
1
1
PTS (-) PURPLE - 01
M5
M4
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
03 BROWN/RED - CANH 103 BROWN/RED - CANH 104 BROWN/YELLOW - CANL 104 BROWN/YELLOW - CANL 1
1: WHITE
2: WHITE
MAIN BODY ECU, DRIVER SIDE DASH (B)
STEERING LOCK (C)
CANH (DATA) RED - 14
CANL (DATA) WHITE - 13
PTS SWITCH (A)
06 BLUE/WHITE•BLACK DOT06 BLUE/WHITE•BLACK DOT
08 WHITE/PURPLE•BLACK DOT
01 GREEN•BLACK DOT - LOCK (-) OUTPUT01 GREEN•BLACK DOT - LOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT
07 EMPTY07 EMPTY
09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT12 WHITE•BLACK DOT12 WHITE•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01 EMPTY01 EMPTY02 EMPTY02 EMPTY
05 BLUE/RED05 BLUE/RED06 BLUE/YELLOW06 BLUE/YELLOW07 EMPTY07 EMPTY08 ORANGE08 ORANGE09 YELLOW09 YELLOW10 EMPTY10 EMPTY11 GRAY/RED11 GRAY/RED12 GRAY/YELLOW12 GRAY/YELLOW13 GREEN/RED - SLP (-) OUTPUT13 GREEN/RED - SLP (-) OUTPUT14 ORANGE/WHITE14 ORANGE/WHITE15 BROWN15 BROWN16 ORANGE/BLACK - GROUND (-) INPUT16 ORANGE/BLACK - GROUND (-) INPUT17 PINK - IGNITION (+) IN/OUT17 PINK - IGNITION (+) IN/OUT18 PURPLE18 PURPLE19 RED - 12V (+) INPUT19 RED - 12V (+) INPUT20 BLACK - GROUND (-)20 BLACK - GROUND (-)
01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE03 GRAY/RED•BLUE DOT03 GRAY/RED•BLUE DOT04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE05 GRAY•BLUE DOT - GROUND (-) INPUT05 GRAY•BLUE DOT - GROUND (-) INPUT06 WHITE•BLUE DOT06 WHITE•BLUE DOT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
HORN (-)
TRUNK (-) GRAY - 05
SLP (-) LTGREEN - 04
IGNITION (+) RED - 06
12V (+) BLACK - 07
HOOD SWITCH
1
2
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH ONE.
WITHOUT OEM HOOD STATUS ONLY
CONNECTION REQUIRED ONLY IF IDLE MODE IS DESIRED
AUTOLIGHT (-) BLACK - 08
LOCK (-) PURPLE - 29
UNLOCK (-) LTBLUE - 02
M1
04 PINK/WHITE
01 ORANGE01 ORANGE02 RED02 RED03 PURPLE03 PURPLE
05 PINK05 PINK
07 RED07 RED08 BLACK08 BLACK
06 WHITE06 WHITE
!
M3
M1
M2 M5M4
PAGE 5 OF 8
Patent No. US 8,856,780 CA 2759622 2017-2019 Toyota Highlander PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 176: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/176.jpg)
01
ENGINE
START
STOP
STOP ACC ON STARTON
02
03
ENGINE
START
STOP
STOP ACC ON STARTSTOP
04
05
ENGINE
START
STOP
STOP ACC ON STARTON
06
07
ENGINE
START
STOP
STOP ACC ON STARTSTOP
08
ENGINE
START
STOP
STOP ACC ON STARTSTART
09
10
11
12
13
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Push start button twice [2x] to ON position.
Wait, if LED 1 turns solid GREEN for 2 seconds, proceed to step 7. If LED 1 flashes GREEN rapidly, proceed to step 3.
Push start button once [1x] to OFF position.
Wait, LED 1 will turn solid RED. (This may take up to 5 minutes.)
Push start button twice [2x] to ON position.
Wait, LED 1 will turn solid GREEN for 2 seconds.
Push start button once [1x] to OFF position.
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming button.
Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
PAGE 6 OF 8
Patent No. US 8,856,780 CA 2759622 2017-2019 Toyota Highlander PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 177: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/177.jpg)
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
4 Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
11 Open hood.
12If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
PAGE 7 OF 8
Patent No. US 8,856,780 CA 2759622 2017-2019 Toyota Highlander PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 178: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/178.jpg)
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
PAGE 8 OF 8
Patent No. US 8,856,780 CA 2759622 2017-2019 Toyota Highlander PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 179: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/179.jpg)
Patent No. US 8,856,780 CA 2759622
20181121
REVISION DATE
ADS-RSA-TL7-[HC2352AC]
FIRMWARE
HC2352AC
HARDWARE
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED.
VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
ACCESSORIES
DOCUMENT NUMBER
2016-2019 TOYOTA LAND CRUISER PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2018
INSTALL GUIDE
TERMS OF USEAutomotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users.
![Page 180: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/180.jpg)
T006_H
T-HARNESS / COMPONENT LOCATOR - 1 OF 1
A
B
C
PAGE 2 OF 8
Patent No. US 8,856,780 CA 2759622 2016-2019 Toyota Land Cruiser PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 181: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/181.jpg)
4
5
3
1
T006_H
1
3
4
2
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
NOT REQUIRED FOR BASIC INSTALLATION.INSERT WIRE TERMINALS IN MS3 CONNECTOR FOR OPTIONAL OUTPUTS.REFER TO PRODUCT GUIDE FOR MORE INFORMATION.
T-HARNESS / WIRING DIAGRAM - 1 OF 1
2: WHITE
1
1: BODY ECU
M5
M4
M2
M3
0404
03030404
PTS SWITCH (A)
MAIN BODY ECU, DRIVER SIDE DASH (B)
0606
08
010102020303
0505
0707
0909
11111212
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01010202
050506060707080809091010
121213131414151516161717181819192020
0101
04040505
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
1010
HOOD SWITCH
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CONNECT IF VEHICLE IS NOTEQUIPPED WITH OEM HOOD PIN
POWER LIFTGATE (-) RED - 05
PTS (-) BLUE - 01
CONNECTION REQUIRED IF IDLE MODE IS DESIRED.
03030202
0606
1111
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
JS4
MS3
MS1
VS3
VS4JS8
TL6
RED/WHITE•BLACK DOT - TRUNK (-) OUTPUTRED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
GREEN/BLACK•BLACK DOTGREEN/BLACK•BLACK DOTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUT
PURPLEPURPLE
VS1
VS2
MS2
1: BODY ECU HARNESS
NCNC
JS7
TL2/7
JS6
!
2
2
SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.
6
5 4 3 2 1
10 9 8 7
16
28
15
27
14
26
13
25
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4 3 2 1
STEERING LOCK (C)
JS1 JS2
1: STEERING LOCK
1: STEERING LOCK HARNESS
JS5
M1
04
010102020303
0505
07070808
0606
!
M3
M1
M2 M5M4
PAGE 3 OF 8
Patent No. US 8,856,780 CA 2759622 2016-2019 Toyota Land Cruiser PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 182: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/182.jpg)
T006_W
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
A
C
B
PAGE 4 OF 8
Patent No. US 8,856,780 CA 2759622 2016-2019 Toyota Land Cruiser PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 183: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/183.jpg)
4
!
3
10 11 12 13 14 15 16 17 18
19 20 21 22 23 24 25 26 27 29 30
1 2 3 4 5 6
7 8
29
2
8 9
28
7 6 5 4 3 2 1
1
1
3
1
2
2
6
5 4 3 2 1
10 9 8 7
16
28
15
27
14
26
13
25
12
24
11
23
10
22
9
21
8
20
7
19
6
18
5
17
4 3 2 1
T006_W
1
2
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
HARDWIRE / WIRING DIAGRAM - 1 OF 1
1
1
PTS (-) BLUE - 01
M5
M4
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
03 BROWN/RED - CANH 103 BROWN/RED - CANH 104 BROWN/YELLOW - CANL 104 BROWN/YELLOW - CANL 1
1: WHITE
2: WHITE
MAIN BODY ECU, DRIVER SIDE DASH (B)
STEERING LOCK (C)
CANH (DATA) GREEN - 14
CANL (DATA) WHITE - 13
AUTOLIGHT (-) PINK - 08
LOCK (-) GREEN - 29
UNLOCK (-) PINK - 02
PTS SWITCH (A)
06 BLUE/WHITE•BLACK DOT06 BLUE/WHITE•BLACK DOT
08 WHITE/PURPLE•BLACK DOT
01 GREEN•BLACK DOT - LOCK (-) OUTPUT01 GREEN•BLACK DOT - LOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT03 RED/WHITE•BLACK DOT - TRUNK (-) OUTPUT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT
07 EMPTY07 EMPTY
09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT12 WHITE•BLACK DOT12 WHITE•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01 EMPTY01 EMPTY02 EMPTY02 EMPTY
05 BLUE/RED05 BLUE/RED06 BLUE/YELLOW06 BLUE/YELLOW07 EMPTY07 EMPTY08 ORANGE08 ORANGE09 YELLOW09 YELLOW10 EMPTY10 EMPTY11 GRAY/RED11 GRAY/RED12 GRAY/YELLOW12 GRAY/YELLOW13 GREEN/RED - SLP (-) OUTPUT13 GREEN/RED - SLP (-) OUTPUT14 ORANGE/WHITE14 ORANGE/WHITE15 BROWN15 BROWN16 ORANGE/BLACK - GROUND (-) INPUT16 ORANGE/BLACK - GROUND (-) INPUT17 PINK - IGNITION (+) IN/OUT17 PINK - IGNITION (+) IN/OUT18 PURPLE18 PURPLE19 RED - 12V (+) INPUT19 RED - 12V (+) INPUT20 BLACK - GROUND (-)20 BLACK - GROUND (-)
01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE03 GRAY/RED•BLUE DOT03 GRAY/RED•BLUE DOT04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE05 GRAY•BLUE DOT - GROUND (-) INPUT05 GRAY•BLUE DOT - GROUND (-) INPUT06 WHITE•BLUE DOT06 WHITE•BLUE DOT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
HORN (-)
TRUNK (-) BLACK - 05
SLP (-) RED - 04
IGNITION (+) PINK - 06
12V (+) GREEN - 07
HOOD SWITCH
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
WITHOUT OEM HOOD STATUS ONLY
CONNECTION REQUIRED ONLY IF IDLE MODE IS DESIREDM1
04 PINK/WHITE
01 ORANGE01 ORANGE02 RED02 RED03 PURPLE03 PURPLE
05 PINK05 PINK
07 RED07 RED08 BLACK08 BLACK
06 WHITE06 WHITE
!
M3
M1
M2 M5M4
PAGE 5 OF 8
Patent No. US 8,856,780 CA 2759622 2016-2019 Toyota Land Cruiser PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 184: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/184.jpg)
01
ENGINE
START
STOP
STOP ACC ON STARTON
02
03
ENGINE
START
STOP
STOP ACC ON STARTSTOP
04
05
ENGINE
START
STOP
STOP ACC ON STARTON
06
07
ENGINE
START
STOP
STOP ACC ON STARTSTOP
08
ENGINE
START
STOP
STOP ACC ON STARTSTART
09
10
11
12
13
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Push start button twice [2x] to ON position.
Wait, if LED 1 turns solid GREEN for 2 seconds, proceed to step 7. If LED 1 flashes GREEN rapidly, proceed to step 3.
Push start button once [1x] to OFF position.
Wait, LED 1 will turn solid RED. (This may take up to 5 minutes.)
Push start button twice [2x] to ON position.
Wait, LED 1 will turn solid GREEN for 2 seconds.
Push start button once [1x] to OFF position.
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming button.
Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
PAGE 6 OF 8
Patent No. US 8,856,780 CA 2759622 2016-2019 Toyota Land Cruiser PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 185: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/185.jpg)
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
4 Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
11 Open hood.
12If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
PAGE 7 OF 8
Patent No. US 8,856,780 CA 2759622 2016-2019 Toyota Land Cruiser PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 186: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/186.jpg)
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
PAGE 8 OF 8
Patent No. US 8,856,780 CA 2759622 2016-2019 Toyota Land Cruiser PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 187: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/187.jpg)
Patent No. US 8,856,780 CA 2759622
20181121
REVISION DATE
ADS-RSA-TL7-[HC2352AC]
FIRMWARE
HC2352AC
HARDWARE
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED.
VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
ACCESSORIES
DOCUMENT NUMBER
2017-2018 TOYOTA PRIUS PRIME PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2018
INSTALL GUIDE
TERMS OF USEAutomotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users.
![Page 188: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/188.jpg)
T008_W
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
A
CB
D
PAGE 2 OF 6
Patent No. US 8,856,780 CA 2759622 2017-2018 Toyota Prius Prime PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 189: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/189.jpg)
4
!
3
10 11 12 13 14 15 16 17 18
19 20 21 22 23 24 25 26 27 29 30
1 2 3 4 5 6
7 8
29
2
8 9
28
1
1
3
1
2
2
6
5 4 3 2 1
10 9 8 7
T008_W
10 11 12 13 14 15 16
1 2 3 4 5 6 7 8
9
323130292827262524 232221
201918171615141312 1110 9
8 7 6 5 4 3 2 1
1
1
2
54 53 52 51 50 49 48 47 46 45 44 43 42 41
40 39 38 37 36 35 34 33 32 31 30 29 28 27
26 25 24 23 22 21 20 19 18 17 16 15 14
13 12 11 10 9 8 7 6 5 4 3 2 1
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
HARDWIRE / WIRING DIAGRAM - 1 OF 1
1: BLACK
1: BLACK
1: WHITE
PTS (-) GREEN - 01
STARTER (+) BLACK - 04
M5
M4
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
03 BROWN/RED - CANH 103 BROWN/RED - CANH 104 BROWN/YELLOW - CANL 104 BROWN/YELLOW - CANL 1
1: WHITE
2: WHITE
MAIN BODY ECU, DRIVER SIDE DASH (B)
OBDII (D)
CANH (DATA) LTBLUE - 14
CANL (DATA) WHITE - 13
AUTOLIGHT (-) BLACK OR WHITE - 08
LOCK (-) PURPLE - 29
UNLOCK (-) GREEN - 02
PTS SWITCH (A)
HYBRID VEHICLE CONTROL ECU, BEHIND GLOVE BOX (C)HYBRID VEHICLE CONTROL ECU, BEHIND GLOVE BOX (C)
06 BLUE/WHITE•BLACK DOT06 BLUE/WHITE•BLACK DOT
08 WHITE/PURPLE•BLACK DOT
01 GREEN•BLACK DOT - LOCK (-) OUTPUT01 GREEN•BLACK DOT - LOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT03 RED/WHITE•BLACK DOT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT
07 EMPTY07 EMPTY
09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT12 WHITE•BLACK DOT12 WHITE•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01 EMPTY01 EMPTY02 EMPTY02 EMPTY
05 BLUE/RED05 BLUE/RED06 BLUE/YELLOW06 BLUE/YELLOW07 EMPTY07 EMPTY08 ORANGE08 ORANGE09 YELLOW09 YELLOW10 EMPTY10 EMPTY11 GRAY/RED11 GRAY/RED12 GRAY/YELLOW12 GRAY/YELLOW13 GREEN/RED13 GREEN/RED14 ORANGE/WHITE14 ORANGE/WHITE15 BROWN15 BROWN16 ORANGE/BLACK - GROUND (-) INPUT16 ORANGE/BLACK - GROUND (-) INPUT17 PINK - IGNITION (+) IN/OUT17 PINK - IGNITION (+) IN/OUT18 PURPLE - STARTER (+) OUTPUT19 RED - 12V (+) INPUT19 RED - 12V (+) INPUT20 BLACK - GROUND (-)20 BLACK - GROUND (-)
01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE03 GRAY/RED•BLUE DOT03 GRAY/RED•BLUE DOT04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE05 GRAY•BLUE DOT - GROUND (-) INPUT05 GRAY•BLUE DOT - GROUND (-) INPUT06 WHITE•BLUE DOT06 WHITE•BLUE DOT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
HORN (-)
IGNITION (+) PURPLE - 10
12V (+) PURPLE - 16
GROUND (-) WHITE/BLACK - 04
HOOD SWITCH
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
WITHOUT OEM HOOD STATUS ONLY
CONNECTION REQUIRED ONLY IF IDLE MODE IS DESIRED
M1
04 PINK/WHITE
01 ORANGE01 ORANGE02 RED02 RED03 PURPLE03 PURPLE
05 PINK05 PINK
07 RED07 RED08 BLACK08 BLACK
06 WHITE06 WHITE
!
M3
M1
M2 M5M4
PAGE 3 OF 6
Patent No. US 8,856,780 CA 2759622 2017-2018 Toyota Prius Prime PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 190: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/190.jpg)
01
ENGINE
START
STOP
STOP ACC ON STARTON
02
03
ENGINE
START
STOP
STOP ACC ON STARTSTOP
04
05
ENGINE
START
STOP
STOP ACC ON STARTON
06
07
ENGINE
START
STOP
STOP ACC ON STARTSTOP
08
ENGINE
START
STOP
STOP ACC ON STARTSTART
09
10
11
12
13
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Push start button twice [2x] to ON position.
Wait, if LED 1 turns solid GREEN for 2 seconds, proceed to step 7. If LED 1 flashes GREEN rapidly, proceed to step 3.
Push start button once [1x] to OFF position.
Wait, LED 1 will turn solid RED. (This may take up to 5 minutes.)
Push start button twice [2x] to ON position.
Wait, LED 1 will turn solid GREEN for 2 seconds.
Push start button once [1x] to OFF position.
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming button.
Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
PAGE 4 OF 6
Patent No. US 8,856,780 CA 2759622 2017-2018 Toyota Prius Prime PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 191: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/191.jpg)
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
4 Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
11 Open hood.
12If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
PAGE 5 OF 6
Patent No. US 8,856,780 CA 2759622 2017-2018 Toyota Prius Prime PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 192: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/192.jpg)
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
PAGE 6 OF 6
Patent No. US 8,856,780 CA 2759622 2017-2018 Toyota Prius Prime PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 193: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/193.jpg)
Patent No. US 8,856,780 CA 2759622
20181121
REVISION DATE
ADS-RSA-TL7-[HC2352AC]
FIRMWARE
HC2352AC
HARDWARE
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED.
VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
ACCESSORIES
DOCUMENT NUMBER
2016-2018 TOYOTA PRIUS PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2018
INSTALL GUIDE
TERMS OF USEAutomotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users.
![Page 194: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/194.jpg)
T008_W
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
A
CB
D
PAGE 2 OF 6
Patent No. US 8,856,780 CA 2759622 2016-2018 Toyota Prius PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 195: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/195.jpg)
4
!
3
10 11 12 13 14 15 16 17 18
19 20 21 22 23 24 25 26 27 29 30
1 2 3 4 5 6
7 8
29
2
8 9
28
1
1
3
1
2
2
6
5 4 3 2 1
10 9 8 7
T008_W
10 11 12 13 14 15 16
1 2 3 4 5 6 7 8
9
323130292827262524 232221
201918171615141312 1110 9
8 7 6 5 4 3 2 1
1
1
2
54 53 52 51 50 49 48 47 46 45 44 43 42 41
40 39 38 37 36 35 34 33 32 31 30 29 28 27
26 25 24 23 22 21 20 19 18 17 16 15 14
13 12 11 10 9 8 7 6 5 4 3 2 1
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
HARDWIRE / WIRING DIAGRAM - 1 OF 1
1: BLACK
1: BLACK
1: WHITE
PTS (-) GREEN - 01
STARTER (+) BLACK - 04
M5
M4
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
03 BROWN/RED - CANH 103 BROWN/RED - CANH 104 BROWN/YELLOW - CANL 104 BROWN/YELLOW - CANL 1
1: WHITE
2: WHITE
MAIN BODY ECU, DRIVER SIDE DASH (B)
OBDII (D)
CANH (DATA) LTBLUE - 14
CANL (DATA) WHITE - 13
AUTOLIGHT (-) BLACK OR WHITE - 08
LOCK (-) PURPLE - 29
UNLOCK (-) GREEN - 02
PTS SWITCH (A)
HYBRID VEHICLE CONTROL ECU, BEHIND GLOVE BOX (C)HYBRID VEHICLE CONTROL ECU, BEHIND GLOVE BOX (C)
06 BLUE/WHITE•BLACK DOT06 BLUE/WHITE•BLACK DOT
08 WHITE/PURPLE•BLACK DOT
01 GREEN•BLACK DOT - LOCK (-) OUTPUT01 GREEN•BLACK DOT - LOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT03 RED/WHITE•BLACK DOT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT
07 EMPTY07 EMPTY
09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT12 WHITE•BLACK DOT12 WHITE•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01 EMPTY01 EMPTY02 EMPTY02 EMPTY
05 BLUE/RED05 BLUE/RED06 BLUE/YELLOW06 BLUE/YELLOW07 EMPTY07 EMPTY08 ORANGE08 ORANGE09 YELLOW09 YELLOW10 EMPTY10 EMPTY11 GRAY/RED11 GRAY/RED12 GRAY/YELLOW12 GRAY/YELLOW13 GREEN/RED13 GREEN/RED14 ORANGE/WHITE14 ORANGE/WHITE15 BROWN15 BROWN16 ORANGE/BLACK - GROUND (-) INPUT16 ORANGE/BLACK - GROUND (-) INPUT17 PINK - IGNITION (+) IN/OUT17 PINK - IGNITION (+) IN/OUT18 PURPLE - STARTER (+) OUTPUT19 RED - 12V (+) INPUT19 RED - 12V (+) INPUT20 BLACK - GROUND (-)20 BLACK - GROUND (-)
01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE03 GRAY/RED•BLUE DOT03 GRAY/RED•BLUE DOT04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE05 GRAY•BLUE DOT - GROUND (-) INPUT05 GRAY•BLUE DOT - GROUND (-) INPUT06 WHITE•BLUE DOT06 WHITE•BLUE DOT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
HORN (-)
IGNITION (+) PURPLE - 10
12V (+) PURPLE - 16
GROUND (-) WHITE/BLACK - 04
HOOD SWITCH
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
WITHOUT OEM HOOD STATUS ONLY
CONNECTION REQUIRED ONLY IF IDLE MODE IS DESIRED
M1
04 PINK/WHITE
01 ORANGE01 ORANGE02 RED02 RED03 PURPLE03 PURPLE
05 PINK05 PINK
07 RED07 RED08 BLACK08 BLACK
06 WHITE06 WHITE
!
M3
M1
M2 M5M4
PAGE 3 OF 6
Patent No. US 8,856,780 CA 2759622 2016-2018 Toyota Prius PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 196: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/196.jpg)
01
ENGINE
START
STOP
STOP ACC ON STARTON
02
03
ENGINE
START
STOP
STOP ACC ON STARTSTOP
04
05
ENGINE
START
STOP
STOP ACC ON STARTON
06
07
ENGINE
START
STOP
STOP ACC ON STARTSTOP
08
ENGINE
START
STOP
STOP ACC ON STARTSTART
09
10
11
12
13
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Push start button twice [2x] to ON position.
Wait, if LED 1 turns solid GREEN for 2 seconds, proceed to step 7. If LED 1 flashes GREEN rapidly, proceed to step 3.
Push start button once [1x] to OFF position.
Wait, LED 1 will turn solid RED. (This may take up to 5 minutes.)
Push start button twice [2x] to ON position.
Wait, LED 1 will turn solid GREEN for 2 seconds.
Push start button once [1x] to OFF position.
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming button.
Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
PAGE 4 OF 6
Patent No. US 8,856,780 CA 2759622 2016-2018 Toyota Prius PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 197: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/197.jpg)
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
4 Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
11 Open hood.
12If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
PAGE 5 OF 6
Patent No. US 8,856,780 CA 2759622 2016-2018 Toyota Prius PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 198: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/198.jpg)
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
PAGE 6 OF 6
Patent No. US 8,856,780 CA 2759622 2016-2018 Toyota Prius PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 199: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/199.jpg)
Patent No. US 8,856,780 CA 2759622
20181121
REVISION DATE
ADS-RSA-TL7-[HC2352AC]
FIRMWARE
HC2352AC
HARDWARE
ATTENTION: TO COMPLETE THIS INSTALLATION SOME ACCESSORIES MAY BE REQUIRED.
VISIT OUR WEBSITE TO SEE ALL THE REQUIRED ACCESSORIES FOR YOUR VEHICLE.
ACCESSORIES
DOCUMENT NUMBER
2016-2019 TOYOTA TACOMA PTS AT
www.idatalink.comAutomotive Data Solutions Inc. © 2018
INSTALL GUIDE
TERMS OF USEAutomotive Data Solutions Inc. (“ADS”) products are strictly intended for installation by Certified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the Certified Technician’s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink®. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink® account without notice and decline to offer technical support to non-Certified Technicians, non-compliant Certified Technicians or end users.
![Page 200: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/200.jpg)
T005_H
T-HARNESS / COMPONENT LOCATOR - 1 OF 1
A
BC
PAGE 2 OF 8
Patent No. US 8,856,780 CA 2759622 2016-2019 Toyota Tacoma PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 201: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/201.jpg)
4
5
3
1
T005_H
1
3
4
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
NOT REQUIRED FOR BASIC INSTALLATION.INSERT WIRE TERMINALS IN MS3 CONNECTOR FOR OPTIONAL OUTPUTS.REFER TO PRODUCT GUIDE FOR MORE INFORMATION.
T-HARNESS / WIRING DIAGRAM - 1 OF 1
1
1: BODY ECU
M5
M4
M2
M3
0404
03030404
PTS SWITCH (A)
MAIN BODY ECU, DRIVER SIDE DASH (B)
0606
08
010102020303
0505
0707
0909
11111212
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01010202
050506060707080809091010
121213131414151516161717181819192020
0101
04040505
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
1010
HOOD SWITCH
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CONNECT IF VEHICLE IS NOTEQUIPPED WITH OEM HOOD PIN
PTS (-) GRAY - 01
CONNECTION REQUIRED IF IDLE MODE IS DESIRED.
03030202
0606
1111
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
JS4
MS3
MS1
VS3
VS4
JS8
TL6
RED/WHITE•BLACK DOTRED/WHITE•BLACK DOT
GREEN/BLACK•BLACK DOTGREEN/BLACK•BLACK DOTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUTBLUE/WHITE•BLACK DOT - PTS (-) OUTPUT
PURPLEPURPLE
VS1
VS2
MS2
1: BODY ECU HARNESS
NCNC
JS7
TL2/7
JS6
!
2
2
SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.SOME PARTS OF THE T-HARNESS (JS3, JS4 AND JS8-TL6)ARE NOT USED IN THIS INSTALL DO NOT CONNECT THEM.
6
5 4 3 2 1
10 9 8 7
STEERING LOCK (C)
JS1 JS2
1: STEERING LOCK
1: STEERING LOCK HARNESS
JS5
M1
04
010102020303
0505
07070808
0606
!
M3
M1
M2 M5M4
PAGE 3 OF 8
Patent No. US 8,856,780 CA 2759622 2016-2019 Toyota Tacoma PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 202: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/202.jpg)
T005_W
HARDWIRE / COMPONENT LOCATOR - 1 OF 1
A
B
C
PAGE 4 OF 8
Patent No. US 8,856,780 CA 2759622 2016-2019 Toyota Tacoma PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 203: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/203.jpg)
5
!
4
10 11 12 13 14 15 16 17 18
19 20 21 22 23 24 25 26 27 29 30
1 2 3 4 5 6
7 8
29
2
8 9
28
7 6 5 4 3 2 1
1
1
4
1
2
2
2
3
3
6
5 4 3 2 1
10 9 8 7
T005_W
IMPORTANT:1- NO TAKEOVER AVAILABLE. UPON OPENING VEHICLE DOOR ENGINE WILL SHUTDOWN.
2- ALL DOORS MUST BE CLOSED TO REMOTE START VEHICLE.
CUT LOOP FOR AUTOMATIC TRANSMISSION ONLYCUT LOOP FOR AUTOMATIC TRANSMISSION ONLY
HARDWIRE / WIRING DIAGRAM - 1 OF 1
1
1
PTS (-) GRAY - 01
M5
M4
M2
M3
04 GREEN/WHITE•BLACK DOT04 GREEN/WHITE•BLACK DOT
03 BROWN/RED - CANH 103 BROWN/RED - CANH 104 BROWN/YELLOW - CANL 104 BROWN/YELLOW - CANL 1
1: WHITE
MAIN BODY ECU, DRIVER SIDE DASH (B)
STEERING LOCK (C)
CANH (DATA) BLACK - 14
CANL (DATA) WHITE - 13
AUTOLIGHT (-) WHITE - 08
LOCK (-) LtBLUE - 29
UNLOCK (-) GREEN - 02
PTS SWITCH (A)
06 BLUE/WHITE•BLACK DOT06 BLUE/WHITE•BLACK DOT
08 WHITE/PURPLE•BLACK DOT
01 GREEN•BLACK DOT - LOCK (-) OUTPUT01 GREEN•BLACK DOT - LOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT02 BLUE•BLACK DOT - UNLOCK (-) OUTPUT03 RED/WHITE•BLACK DOT03 RED/WHITE•BLACK DOT
05 GREEN/BLACK•BLACK DOT05 GREEN/BLACK•BLACK DOT
07 EMPTY07 EMPTY
09 PURPLE/BLACK•BLACK DOT09 PURPLE/BLACK•BLACK DOT
11 BROWN/BLACK•BLACK DOT11 BROWN/BLACK•BLACK DOT12 WHITE•BLACK DOT12 WHITE•BLACK DOT
01 BROWN•SILVER DOT01 BROWN•SILVER DOT02 BLACK/WHITE•SILVER DOT02 BLACK/WHITE•SILVER DOT03 PURPLE•SILVER DOT03 PURPLE•SILVER DOT04 GREEN•SILVER DOT04 GREEN•SILVER DOT05 PURPLE/WHITE•SILVER DOT05 PURPLE/WHITE•SILVER DOT06 WHITE/BLUE•SILVER DOT06 WHITE/BLUE•SILVER DOT
08 BLUE•SILVER DOT08 BLUE•SILVER DOT09 GRAY/BLACK•SILVER DOT09 GRAY/BLACK•SILVER DOT10 EMPTY10 EMPTY
01 EMPTY01 EMPTY02 EMPTY02 EMPTY
05 BLUE/RED05 BLUE/RED06 BLUE/YELLOW06 BLUE/YELLOW07 EMPTY07 EMPTY08 ORANGE08 ORANGE09 YELLOW09 YELLOW10 EMPTY10 EMPTY11 GRAY/RED11 GRAY/RED12 GRAY/YELLOW12 GRAY/YELLOW13 GREEN/RED - SLP (-) OUTPUT13 GREEN/RED - SLP (-) OUTPUT14 ORANGE/WHITE14 ORANGE/WHITE15 BROWN15 BROWN16 ORANGE/BLACK - GROUND (-) INPUT16 ORANGE/BLACK - GROUND (-) INPUT17 PINK - IGNITION (+) IN/OUT17 PINK - IGNITION (+) IN/OUT18 PURPLE18 PURPLE19 RED - 12V (+) INPUT19 RED - 12V (+) INPUT20 BLACK - GROUND (-)20 BLACK - GROUND (-)
01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT01 GRAY/BLACK•BLUE DOT - PTS (-) OUTPUT02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE02 WHITE/BLACK•BLUE DOT - AUTOLIGHT (-) VEHICLE SIDE03 GRAY/RED•BLUE DOT03 GRAY/RED•BLUE DOT04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE04 WHITE/RED•BLUE DOT - AUTOLIGHT (-) CONNECTOR SIDE05 GRAY•BLUE DOT - GROUND (-) INPUT05 GRAY•BLUE DOT - GROUND (-) INPUT06 WHITE•BLUE DOT06 WHITE•BLUE DOT
07 GRAY•SILVER DOT - HOOD (-) INPUT07 GRAY•SILVER DOT - HOOD (-) INPUT
10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT10 WHITE/BLACK•BLACK DOT - HORN (-) OUTPUT
HORN (-)
SLP (-) TAN - 04
IGNITION (+) BLACK - 06
12V (+) RED - 07
HOOD SWITCH
1
INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLEIS NOT EQUIPPED WITH ONE.
WITHOUT OEM HOOD STATUS ONLY
CONNECTION REQUIRED ONLY IF IDLE MODE IS DESIRED
OPTIONAL CONNECTIONS:-IF CONNECTED, OEM AND AFTERMARKET REMOTES
WILL ALWAYS BE SYNCHRONIZED.-IF NOT CONNECTED, USER MUST LOCK VEHICLE DOORS USING
OEM REMOTE OR DOOR REQUEST SWITCH AFTER OPERATINGVEHICLE, EVERY TIME.
FOR MORE INFORMATION, READ "WARNING: DOOR LOCKSYNCHRONIZATION".
M1
04 PINK/WHITE
01 ORANGE01 ORANGE02 RED02 RED03 PURPLE03 PURPLE
05 PINK05 PINK
07 RED07 RED08 BLACK08 BLACK
06 WHITE06 WHITE
!
M3
M1
M2 M5M4
PAGE 5 OF 8
Patent No. US 8,856,780 CA 2759622 2016-2019 Toyota Tacoma PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 204: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/204.jpg)
01
ENGINE
START
STOP
STOP ACC ON STARTON
02
03
ENGINE
START
STOP
STOP ACC ON STARTSTOP
04
05
ENGINE
START
STOP
STOP ACC ON STARTON
06
07
ENGINE
START
STOP
STOP ACC ON STARTSTOP
08
ENGINE
START
STOP
STOP ACC ON STARTSTART
09
10
11
12
13
MODULE PROGRAMMING PROCEDURE - 1 OF 1
Push start button twice [2x] to ON position.
Wait, if LED 1 turns solid GREEN for 2 seconds, proceed to step 7. If LED 1 flashes GREEN rapidly, proceed to step 3.
Push start button once [1x] to OFF position.
Wait, LED 1 will turn solid RED. (This may take up to 5 minutes.)
Push start button twice [2x] to ON position.
Wait, LED 1 will turn solid GREEN for 2 seconds.
Push start button once [1x] to OFF position.
START vehicle for 15 seconds.
Press and hold the brake pedal.
Press and release the module’s programming button.
Release the brake pedal.
Wait, LED 2 will flash GREEN.
Module Programming Procedure completed.
PAGE 6 OF 8
Patent No. US 8,856,780 CA 2759622 2016-2019 Toyota Tacoma PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 205: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/205.jpg)
INSTALLATION CHECKLIST - 1 OF 2
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press the LOCK button once [1x] on the aftermarket keyfob.
Question 1: Do the doors lock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
4 Press the UNLOCK button once [1x] on the aftermarket keyfob.
Question 2: Do the doors unlock?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
5 Press the TRUNK release button once [1x] on the aftermarket keyfob if supported.
Question 3: Does the trunk or hatch open/unlock?
YES: Close trunk or hatch and go to next step.
NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists.
6 Press the AUX 1 button once [1x] on the aftermarket keyfob if supported.
Question 4: Does the driver side sliding door open?
YES: Press the AUX 1 button once [1x] to close the driver sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
7 Press the AUX 2 button once [1x] on the aftermarket keyfob if supported.
Question 5: Does the passenger side sliding door open?
YES: Press the AUX 2 button once [1x] to close the passenger sliding door and go to next step.
NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists.
8 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 6: Does the vehicle remote start?
YES: Go to next step.
NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists.
9 Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle.
Question 7: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If problem persists, press the brake pedal once [1x] to shut down the vehicle and call technical support.
10 RAP and auto light shutdown test
Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists.
11 Open hood.
12If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
13 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
Question 9: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
14 Close hood.
15 Enter vehicle and close the doors.
16 Press the START/STOP button once [1x] on the aftermarket keyfob to remote start vehicle.
17 Wait for the vehicle to start.
18 Press brake pedal.
Question 10: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [1x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support.
19 Exit vehicle.
20 Installation checklist completed.
CHECKLIST - WITH AFTERMARKET KEYFOB
PAGE 7 OF 8
Patent No. US 8,856,780 CA 2759622 2016-2019 Toyota Tacoma PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121
![Page 206: INSTALL GUIDEimages.idatalink.com/corporate/Content/Manuals/RSA-TL7...2018/11/22 · Press and hold the brake pedal. Press and release the module’s programming button. Release the](https://reader034.vdocuments.net/reader034/viewer/2022050101/5f403265ad769a2c82272b11/html5/thumbnails/206.jpg)
INSTALLATION CHECKLIST - 2 OF 2
CHECKLIST - WITH OEM KEYFOB
1 WARNING: Vehicle engine will start many times. Test in a well ventilated area.
2 Close all vehicle doors, hood and trunk.
3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 1: Does the vehicle remote start?
YES: Go to next step.
NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call technical support, if the problem persists.
4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle.
Question 2: Does the vehicle shut down?
YES: Go to next step.
NO: Repeat step. If the problem persists, press on the brake pedal once [1x] to shut down the vehicle and call technical support.
5 RAP Shutdown test
Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown?
YES: Go to next step.
NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support, if the problem persists.
6 Open hood.
7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step.
8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
Question 4: Does the vehicle remote start?
YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test.
NO: Go to next step.
9 Close hood.
10 Enter vehicle and close the doors.
11 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle.
12 Wait for the vehicle to start.
13 Press brake pedal.
Question 5: Does the vehicle shut down?
YES: Go to next step.
NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support.
14 Exit vehicle.
15 Installation checklist completed.
PAGE 8 OF 8
Patent No. US 8,856,780 CA 2759622 2016-2019 Toyota Tacoma PTS AT www.idatalink.comAutomotive Data Solutions Inc. © 2018 ADS-RSA-TL7-[HC2352AC]-EN
20181121