installation fog light 2006 civic 2-door …...© 2005 american honda motor co., inc. - all rights...

© 2005 American Honda Motor Co., Inc. - All Rights Reserved. AII 30890 (0509) 1 of 16

INSTALLATIONINSTRUCTIONS

08V31-SVA-1000-91

Accessory Application Publications No.

Issue Date

PARTS LIST

FOG LIGHTP/N 08V31-SVA-100

2006 CIVIC2-DOOR

SEP 2005

11 Wire ties

Left fog light

Right bracket

Left bracket

Switch harness

Right fog light

Fog light harness

Sub harness

Clip

4 Stepped screws

2 Washer screws

Switch trim(DX model only)

6 Self-tapping screws

Fuse (20A)

Relay

5 Wire ties with clips

Switch

2 Switch covers(DX model only)

Template

All 30890

Ground bolt

2 of 16 AII 30890 (0509) © 2005 American Honda Motor Co., Inc. - All Rights Reserved.

TOOLS AND SUPPLIES REQUIRED

Phillips screwdriver

Flat-tip screwdriver

Ratchet

10 mm Socket

Drill

3 mm and 10 mm Drill bit

Pushpin

Utility knife

Gloves

Eye protection (face shield, safety goggles, etc.)

File

Masking tape

Scissors

Blanket

Shop towel

6 mm Hexagon wrench

Illustration of Fog Lights installed on the Vehicle

INSTALLATION

Customer Information: The information in thisinstallation instruction is intended for use only byskilled technicians who have the proper tools,equipment, and training to correctly and safely addequipment to your vehicle. These proceduresshould not be attempted by “do-it-yourselfers.”

1. Make sure you have the anti-theft code for theradio, then write down the frequencies for thepreset buttons.

2. Disconnect the negative cable from the battery.

3. Remove the radiator cover (four clips).

FOG LIGHTHARNESS

LEFTFOG LIGHT

SUB HARNESS

RELAY

SWITCH

SWITCHHARNESS

RIGHTFOGLIGHT

5311010T

5311021T

RADIATORCOVER EXPANSION

CLIP

CLIPS (2)• Pull out the clip

vertically from thepanel surface.

PANEL


4. With the help of an assistant, remove the frontbumper (ten clips and two self-tapping screws).Set the front bumper on a blanket.

6. Using a utility knife, and working from the front ofthe bumper, carefully cut out the front bumper inthe area shown. Take care not to damage thefront bumper. Remove any burrs from the edgesof the hole.

5311050T

TEMPLATE

5. Apply masking tape to the front bumper aroundthe left fog light area.

5311320T

FRONTBUMPER

MASKINGTAPE

7. Repeat steps 5 and 6 to cut the bumper for theright fog light.

8. Using scissors, cut out the template.

• The template “L” is the mirror image of thetemplate “R”.

5311042T

Cut out thearea fromthe bumper

UTILITYKNIFE

FRONT

FRONTBUMPER

Carefully cut inthe areas shown.

5311032TCLIPS (10)

SELF-TAPPINGSCREWS (2)

FRONTBUMPER

Cut here.


12. Position the left bracket on the left fog light, andinstall the two stepped screws and one washerscrew. Tighten the screws securely.

13. Inside the front bumper, slide the left fog light intothe cutout you made, and secure it with threeself-tapping screws.

10. While wearing eye protection, drill a 10 mm holethrough the bumper at the marked location. Firstdrill with a 3 mm drill bit and finish with a 10 mmdrill bit.

WASHERSCREW

STEPPEDSCREWS (2)

5311080T

LEFT FOG LIGHT

LEFTBRACKET

9. Tape the template marked “L” to the inside of thefront bumper below the left fog light opening.Using a pushpin, pierce the bumper through themark in the template.

11. Repeat steps 9 and 10 to mark and drill the rightside of the front bumper.

14. Repeat steps 12 and 13 to install the right foglight.

5311071T

DRILL(3 mm 10 mm)

MARKFRONTBUMPER

5311091T

SELF-TAPPINGSCREWS (3)

FRONTBUMPER

LEFT FOG LIGHT

5311061T

PUSHPIN

TEMPLATE(L side)MASKING TAPE

FRONTBUMPER


15. Route the fog light harness along the inside ofthe front bumper, and plug the 2-pin connectorsinto the fog lights.

16. Secure the clips attached to the fog light harnessto the left and right fog light brackets.

17. Loosely install five wire ties with clips on the foglight harness.

18. Align the five wire ties with clips with the verticalribs of the front bumper as shown, and tighten thefive wire ties with clips securely.

19. Slide the clip onto the 2-pin connector on the foglight harness, and secure the connector to theright bracket.

20. Remove one bolt from the washer reservoir tankand loosen the two bolts.

5311110T

CLIP

FOG LIGHT HARNESS2-PIN CONNECTOR

RIGHTBRACKET

5307112T

WASHERRESERVOIRTANK

BOLT(Loosen.)

BOLT(Loosen.)

BOLT

5311102T

RIGHTBRACKET

FOG LIGHTHARNESS2-PINCONNECTOR

CLIP

CLIP

FRONT

FRONTBUMPER

WIRE TIE WITHCLIP (5)

WIRE TIE WITH CLIP• Aligning with vertical ribs,

secure the wire ties withclips to the bumper.

VERTICALRIB

FRONT


24. Secure the two clips on the subharness to thevehicle frame. Secure the subharness to thevehicle harness using two wire ties.

25. Reinstall the washer reservoir tank.

26. Plug the 2-pin connector on the subharness intothe 2-pin connector on the fog light harness.

27. Reinstall the front bumper.

5311140T

FRONTBUMPER

FOG LIGHTHARNESS2-PINCONNECTOR

SUB HARNESS2-PIN CONNECTOR

21. Locate the 1-pin connector blue-taped to thevehicle harness, and remove the blue tape to freethe 1-pin connector. Plug the 1-pin connector youjust freed into the 1-pin connector from thesubharness.

22. Route the subharness between the washerreservoir tank and vehicle panel, and route it asshown.

23. Secure the subharness ground terminal to thevehicle frame using a ground bolt.

5307121T

VEHICLEHARNESS

1-PINCONNECTORS

BLUE TAPE(Remove.)

SUB HARNESS

SUBHARNESS

GROUNDTERMINAL

5311301T

WASHERRESERVOIRTANK

VEHICLEFRAME

VEHICLEPANEL GROUND

BOLT

5311131T

WIRETIE

CLIP

SUB HARNESS

VEHICLEFRAME


28. Remove the cover from the trunk lid/fuel fill dooropener (six retaining tabs), and remove one self-tapping screw.

29. Using the ignition key, unlock the opener.

30. Raise the front edge of the left front door silltrim (six clips, retaining tab, and hook).

5202191T

KEY

OPENERLOCKCYLINDER

SELFTAPPINGSCREW

COVERRETAININGTABS (6)

TRUNK LID/FUEL FILLDOOR OPENER

31. Remove the footrest.

• Using a hexagon wrench, remove the lowerclip from the stud bolt.

• Using a flat-tip screwdriver, remove the upperclip from the stud bolt.

32. Pull away the weatherstrip from the left kick paneland remove the left kick panel (two clips).

5202220T

WEATHERSTRIPCLIPS(2)

LEFTKICKPANEL

5311370T

STUD BOLT

UPPERCLIP

FOOTRESTLOWERCLIP

HEXAGONWRENCH

LEFT FRONTDOOR SILL TRIM

FRONT

5311351T

CLIPS (6)

RETAININGTAB

HOOK


34. Remove the driver’s dashboard lower cover (eightclips).

5202121T

DRIVER’SDASHBOARDLOWER COVER

CLIPS (8)

DX model: Continue with step 35.All other models: Go to step 38.

35. Lower the tilt/telescopic lever, and move thesteering wheel down and toward you. Aftermoving the steering wheel, return the tilt/telescopic lever to its original position.

33. If equipped, remove the driver’s dashboard undercover (turn the lock knob 90° counterclockwise,and release the two clips and pin).

5202112T

CLIPS (2)

DRIVER’SDASHBOARDUNDER COVER

KNOB

36. Cover the combination switch with a shop towelto protect it from damage.

5831010H

TILT/TELESCOPICLEVER

STEERINGWHEEL

SHOP TOWEL

COMBINATIONSWITCH


39. Insert the white/red and blue terminals from theswitch harness into the white 34-pin connector.Reinstall the cover.

40. Reinstall the three vehicle connectors.38. Remove the vehicle’s green 42-pin connector,white 34-pin connector, and the blue 21-pinconnector from the fuse box by pushing theretaining tab and raising the lock on eachconnector. Close the lock on the white 34-pinconnector, then slide the cover off the connector.

37. Apply masking tape to the instrument panel asshown, and remove the meter panel (one self-tapping screw, 11 clips, and one connector).

5311150T

WHITE/REDTERMINAL

BLUETERMINAL

Harness Side View

SWITCH HARNESSTERMINAL

SWITCHHARNESS

LOCK LEVER

5307163T

FUSEBOX COVER

Push.

GREEN CONNECTOR

WHITE CONNECTOR

BLUE CONNECTOR

Slide.

VEHICLE’SWHITE 34-PINCONNECTOR

Push.

Push.

41. Plug the switch harness 6-pin connector into thefuse box.

5311160T

<Front view>

FUSEBOX

VEHICLE 6-PINCONNECTOR

SWITCH HARNESS6-PIN CONNECTOR

SWITCHHARNESS

CLIPS (11) 5624100B

SELF-TAPPINGSCREW

MASKINGTAPE

METERPANEL

VEHICLECONNECTOR


46. Plug the relay into the switch harness relay block,then slide the relay block onto the vehicle bracketstay.

5307190T

RELAY

VEHICLEBRACKET STAY

SWITCHHARNESSRELAYBLOCK

SWITCHHARNESS

NOTE: If the fuse box 6-pin connector is alreadybeing used by another accessory, unplug its 6-pinconnector from the fuse box. Locate the 6-pinconnector taped to the switch harness, and removethe dummy connector from the connector. Plug theother accessory’s harness 6-pin connector into theswitch harness, and plug the switch harness 6-pinconnector into the fuse box.

42. Route the terminal on the switch harness asshown.

43. Disconnect the vehicle 14-pin connector.

44. Slide back the retainer on the vehicle 14-pinconnector, and insert the violet terminal from theswitch harness into the 14-pin connector. Closethe retainer, and reconnect the 14-pin connector.

5311170T

SWITCHHARNESS

SWITCH HARNESSVIOLET TERMINAL

Harness Side View

VEHICLE 14-PINCONNECTOR

RETAINER

45. Route the switch harness relay block above theknee bolster.

5311310T

DUMMYCONNECTOR(Discard.)


OTHER ACCESSORYHARNESS 6-PINCONNECTOR

KNEE BOLSTER SWITCHHARNESS

5307180T

SWITCHHARNESSRELAYBLOCK


48. Locate the 1-pin connector blue-taped to thevehicle harness. Plug the 1-pin connector into theswitch harness 1-pin connector.

5306260T

SELF-TAPPINGSCREW

POCKET(Discard.)

METERPANEL

47. Remove the vehicle ground bolt. Install the switchharness ground terminal, then reinstall the groundbolt.

5311200T

SWITCHHARNESS

VEHICLEGROUNDBOLT (Reuse.)

SWITCH HARNESSGROUND TERMINAL

FRONT

49. Install the fog light switch:

DX Model

• Remove the pocket from the meter panel (threeself-tapping screws).

5311212TSWITCHHARNESS

1-PINCONNECTOR

• Install the switch trim to the meter panel with thethree self-tapping screws.

5311220T

SELF-TAPPINGSCREW(Reuse.) METER

PANEL

SWITCH

SWITCHCOVER

SWITCHTRIM

SWITCHCOVER

• Install the switch and two switch covers into theswitch trim.


• Plug the switch harness 5-pin connector into theswitch, reconnect the one connector, and reinstallthe meter panel.

5311230T


SWITCH

METERPANEL

LX, EX, Si model

• While wearing gloves, push the switch cover outfrom the inner side of the meter panel.

• Route the switch harness 5-pin connector throughthe hole.

• Plug the switch harness 5-pin connector into theswitch and install the switch into the meter panel.

5311330T

METERPANEL

SWITCH COVER

5311340T

SWITCH

METERPANEL



50. Secure the switch harness to the vehicle harnessand to the knee bolster with nine wire ties in theareas shown.

51. Install the 20A fuse into the fuse box in thelocation shown.

52. Check that all wire harnesses are routed properlyand all connectors are plugged in.

53. Reinstall all removed parts.

54. Reconnect the negative cable to the battery.

USE AND CARE

How to Operate the Fog Lights

• Turn the light switch to the “ ” position(headlights on low beam).

• Press the fog light switch (indicator is on).

NOTE: The fog light lenses can cloud when theoutside temperature is cold; this is normal and shouldgo away in warm weather.

Fog Light Aiming Adjustment

55. Adjust the fog light:

• Adjust the aim according to local laws andregulations.

• To adjust, turn the aiming adjustment knob inor out until the correct aim is obtained.

5307240T

<Front View>

FUSELOCATION“6”

20 AFUSE

FUSEBOX

5311242T

VEHICLEHARNESS

WIRE TIES (9)

KNEE BOLSTER

SWITCHHARNESS

5311251TTo raiseTo lower

AIMINGADJUSTMENTSCREW


56. Reset the clock, and reset the radio stationpresets.

NOTE: Whenever the battery is disconnected, thedriver’s AUTO function is disabled.

57. Start the engine. Push down on the driver’swindow switch until the window is fully open.

58. Pull up on the driver’s window switch fully to closethe window completely, then hold the switch for 2seconds or more.

59. Test the window AUTO function.

2. Disconnect the fog light connector.

3. Remove the bulb.

BULB REPLACEMENT

1. Remove the seven clips from the bottom of thefront bumper, then pull down the under cover andinner fender.

5311270T

FOG LIGHT

CONNECTOR

BULB

5311262T

CLIP (7)Pull down.

INNERFENDER

UNDERCOVER


4. Install the new bulb and socket into the fog light.

• Use only a genuine Honda halogen light bulb ofspecified wattage.

Rating: 12V 55W H11 Halogen Light Bulb P/N33165-S5A-003

• Do not touch the bulb. Oily or greasysubstances on the bulb can shorten its servicelife due to the heat produced when the bulb isturned on. If the bulb is accidentally touched,wipe it clean with a soft cloth that has beendampened with a denatured alcohol or a milddetergent solution.

• Align the tab on the fog light with the cutout inthe bulb when installing the new bulb. If notaligned, the fog light may annoy oncomingdrivers.

5. Reinstall the removed parts in the reverse orderof removal.

• Check that the wire harnesses are notpinched.

6. Check the operation of the fog light; adjust theaiming if necessary.

BULB

FOG LIGHT

5311280T


5311292T

MULTIPLEXINTEGRATEDCONTROL UNIT

UNDER-DASH FUSE/RELAY BOX

RED/BLK

0 1

PUR

BLU

BLU

BLK

RELAY

WHT/RED

FOG LIGHTFUSE 20A

HEADLIGHT SWITCH

Low HiOFF

ONFO

G L

IGH

TS

WIT

CH OFF - - - -

BLK BRN BROWNBLACK

YEL ORN ORANGEYELLOW

BLU PUR PURPLEBLUE

GRN NAT NATURALGREEN

RED PNK PINKRED

WHT GRY GRAYWHITE

LT BLU LT GRN LIGHT GREENLIGHT BLUE- - -ON

UNDER-HOOD FUSE/RELAY BOX

BATTERY100 A 80 A

RIGHTFRONTFOG LIGHT

LEFTFRONTFOG LIGHT

SWITCHILLUMINATION

BLK RED

DASH LIGHTBRIGHTNESSCONTROLLER

HOT IN COMBINATIONLIGHT SWITCH or

SWITCH

CIRCUIT DIAGRAM

installation fog light 2006 civic 2-door …...© 2005 american honda motor co., inc. - all rights...

Documents