INSTALLATION INSTRUCTIONS FOR PART 99-8209

99-8209

APPLICATIONSSCION

xA 2004-2006

xB 2004-2011

tC 2005-2010

xD 2008-2010

KIT FEATURES

• DIN Radio Provision with Pocket• ISO Mount Radio Provision with Pocket

A) Radio Housing • B) Brackets Set 1 • C) Brackets Set 2 • D) ISO Snap-In Brackets • E) Trim Plate

KIT COMPONENTS

A

Phillips Screwdriver • Panel Removal Tool • Socket Set

1-800-221-0932

© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION

www.metraonline.com

B

C

TOOLS REQUIRED:

D E

WIRING AND ANTENNA CONNECTIONS(Sold Separately)• 70-1761 Toyota harness - 1987-up• Antenna adapter - Not required

Dash Disassembly

- SCION xA 2004-2006. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

- SCION xB 2004-2011 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

- SCION xB 2008 -2011. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

- SCION tC 2005-2010. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

- SCION xD 2008-2010.. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Kit Assembly- DIN Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6- ISO Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . .7

TABLE OF CONTENTS

99-8209

*Note:

Refer also to the instructions included with the aftermarket radio.

KNOWLEDGE IS POWEREnhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry.Log onto www.installerinstitute.com or call 800-354-6782 for more information and take steps toward a better tomorrow.

99-8209 DASH DISASSEMBLY

Scion xA 2004-2006

A

OFF

HI

B

OFF

HI

COFF

HI

D

OFF

HI

E

1

Disconnect the negative battery ter-minal to prevent an accidental shortcircuit.

1

Pull outward on the (3) climate con-trol knobs and remove. (Figure A)

2

Remove (2) Phillips screws frombehind the outer two climate knobs.(Figure B)

3

Unsnap and remove the trim pieceson each side of the climatecontrol/ashtray/pocket assembly.(Figure C)

4

Remove (2) Phillips screws from thebottom of the climate control/radiotrim panel and unsnap and removethe entire panel. (Figure D)

5

Remove (4) 10 MM bolts securing theradio. Unplug and remove the radio.(Figure E)

6

Continue to final assembly.

99-8209 DASH DISASSEMBLY

Scion xB 2004-2011

2

Disconnect the negative battery ter-minal to prevent an accidental shortcircuit.

1

Pull outward on the (3) climate con-trol knobs and remove. (Figure A)

2

Remove (2) Phillips screws frombehind the outer (2) knobs. (Figure B)

3

Unsnap and remove the entire panelsurrounding the climate controls andthe radio. (Figure C)

4

Remove (4) 10 MM bolts securing theradio. Unplug and remove the radio.

5

Continue to final assembly.

OFF

HI

A

OFF

HI

B

OFF

HI

C

99-8209 DASH DISASSEMBLY

Scion xB 2008-2011

3

Disconnect the negative battery ter-minal to prevent an accidental shortcircuit.

1

Unclip and remove the trim panelaround the radio including the a/cvents. (Figure A)

2

Unclip and remove the trim panel atthe bottom edge of the dash cavity.(Figure A)

3

Remove (4) 10 MM bolts securing theradio. Unplug and remove the radio.(Figure B)

4

Continue to final assembly.

A

B

99-8209 DASH DISASSEMBLY

Scion tC 2005-2010

4

Disconnect the negative battery ter-minal to prevent an accidental shortcircuit.

1

Unsnap trim from around shifter. (Notnecessary to be removed). (Figure A)

2

Unsnap and remove panel fromaround radio. (Including climate con-trols and radio door). (Figure B)

3

Remove (2)10MM nuts from the topmounting locations and two Phillipsscrews from the bottom mountinglocations to remove the radio. (Figure C)

4

Continue to final assembly.

A

B

C

99-8209 DASH DISASSEMBLY

Scion xD 2008-2010

5

Disconnect the negative battery ter-minal to prevent an accidental shortcircuit.

1

Unclip radio trim panel. Unplug andremove panel. (Figure A)

2

Remove (4) Phillips screws securingthe radio. Unplug and remove radio.(Figure B)

3

Remove factory brackets from radio.Retain brackets for use during kitassembly. (Figure C)

4

Continue to final assembly.

A

B

C

99-8209 KIT ASSEMBLY

6

A

B

CD

Slide the Mounting Brackets onto thesides of the Radio Housing until theside clips engage. Note: Use bracketset 1 for xA, xB, and tC. Use bracketset 2 for the 2008 xB and xD. (Figure A)

1

For bracket set 1 cut and remove allmounting tabs except the tabs beingused for your application. Note: Tabsare marked xA, xB and tC. For bracket

2

Slide the DIN cage into the RadioHousing and secure by bending themetal locking tabs outward. (Figure C)

3

Slide the aftermarket radio into thecage until it snaps into place. (Figure D)

4

Continue to final assembly.

*Note: Refer also to the instructions included with the aftermarket radio.

DIN RADIO PROVISION WITH POCKET

99-8209 KIT ASSEMBLY

7

Slide the corresponding mountingbrackets onto the sides of the RadioHousing until the side clips engage.Note: Use bracket set 1 for xA, xB,and tC Use bracket set 2 for the 2008xB and xD. (Figure A)

1

For bracket set 1 cut and remove allmounting tabs except the tabs beingused for your application. Note: Tabsare marked xA, xB and tC. For bracketset 2 skip to step 3. (Figure B)

2

Mount the ISO Brackets to the radiousing the screws supplied with theradio. (Figure C)

3

Slide the radio into the radio housinguntil it snaps into place. (Figure D)

4

Snap the Trim Plate onto the front ofthe Radio Housing. (Figure D)

5

Continue to final assembly.

*Note: Refer also to the instructions included with the aftermarket radio.

ISO MOUNT RADIO PROVISION WITH POCKET

A

B

CD

99-8209 FINAL ASSEMBLY

FINAL ASSEMBLY

(A) Strip wire ends back 1/2"

B) Twist ends together

C) Solder

D) Tape

A

B

C

D

Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ-ually tape off the ends of any unused wires to prevent electrical short circuit.)

Re-connect the negative battery terminal and test the unit for proper operation.

Reassemble radio and dash assemblies in reverse order of disassembly.

1

2

3

FINAL WIRING CONNECTIONS

Make wiring connections using the EIA color code chart shown below and the instructions included with thehead unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and

individually tape off ends of any unused wires to prevent electrical short circuit.

METRA / EIA WIRING CODE

12V Ignition / Acc . . . . . . . . . . Red

12V Batt / Memory. . . . . . . . . Yellow

Ground. . . . . . . . . . . . . . . . . . Black*

Power Antenna. . . . . . . . . . . . Blue

Amp Turn-On . . . . . . . . . . . . . Blue / White

Amp Ground. . . . . . . . . . . . . . Black / White

Illumination . . . . . . . . . . . . . . Orange

Dimmer . . . . . . . . . . . . . . . . . Orange / White

Right Front (+) . . . . . . . . . . . . Gray

Right Front (-). . . . . . . . . . . . . Gray/ Black

Left Front (+) . . . . . . . . . . . . . White

Left Front (-). . . . . . . . . . . . . . White / Black

Right Rear (+) . . . . . . . . . . . . Violet

Right Rear (-) . . . . . . . . . . . . . Violet / Black

Left Rear (+) . . . . . . . . . . . . . Green

Left Rear (-) . . . . . . . . . . . . . . Green / Black

*NOTE: When a Black wire is not present, ground radio to vehicle chassis. All colors may not be present on all leads due to manufacturer’s specifications.

8

NOTES

9

99-8209

99-8209 INSTRUCTIONS

1-800-221-0932

REV. 11/18/10 © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION INST99-8209

www.metraonline.com