installation, operation and maintenanceassets.greatplainsmfg.com/manuals/pdf/133-322m.pdf · tablet...

Table of Contents Index

Installation,Operation and Maintenance

133-300A, 133-301A, 133-302A,133-319A, 133-320A, and 133-321A

Small Seeds Options for 2004+ 3S-4000 Series Drills

Manufacturing, Inc.www.greatplainsmfg.com

Read the installation manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it!

Cover illustration shows only selected components for one section of one kit.

27425

© Copyright 2017 Printed 2017-08-08 133-322M

EN


ORIGINAL INSTRUCTIONS

133-300A, 133-301A, 133-302A, 133-319A, 133-320A, and 133-321ATable of Contents Index ii

Machine IdentificationRecord your machine details in the log below. If you replace this manual, be sure to transfer this informationto the new manual.

If you, or the dealer, have added Options not originally ordered with the machine, or removed Options thatwere originally ordered, the weights and measurements are no longer accurate for your machine. Updatethe record by adding the machine weight and measurements with the Option(s) weight and measurements.

Dealer Contact Information

Model Number

Serial Number

Machine Height

Machine Length

Machine Width

Machine Weight

Year of Construction

Delivery Date

First Operation

Accessories

Name:

Street:

City/State:

Telephone:

Email:

Dealer’s Customer No.:

Dealer QRC

The QR Code (Quick Reference) to theleft will take you to available dealers forGreat Plains products. Refer to theParts Manual QR Locater for detailedinstructions.

Manual Family QRC

The QR Code (Quick Response) to theleft will take you to this machine’s familyof manuals. Use your smart phone ortablet to scan the QR Code with anappropriate App to begin viewing.

2017-08-08 Table of Contents Index 133-322M

133-300A, 133-301A, 133-302A, 133-319A, 133-320A and 133-321ACover Index v

Table of Contents

Important Safety Information.................................................1Introduction.............................................................................3

Description of Unit .............................................................3Compatible Drills ...............................................................3Compatible Kits .................................................................3Document Family...............................................................3Using This Manual.............................................................4

Definitions...................................................................4Call-Outs ....................................................................4

Owner Assistance..............................................................4Installation Instructions .........................................................5

Before You Start ................................................................5Tools Required ..................................................................5Prepare Drill.......................................................................5Other Options ....................................................................5Remove Corner Hardware.................................................6

Left Section Corner Hardware....................................6Right Section Corner Hardware .................................6Center Section Corner Hardware ...............................6Center Section Corner hardware................................7

Install Mounts & Meter Drives............................................8Left Mounts.................................................................8Install Meter Drives.....................................................9

Secure Wind Shields .........................................................9Mount Seed Boxes ..........................................................10

Install Light Bracket Extension (S/N C1305L+) ........11Install Center Section Guards and Lights.................12

Install Forward Components............................................13Front Drives without Fertilizer...................................13

Front Drives with Fertilizer .......................................18Small Seeds Drive Chains .......................................20

Install Seed Tubes...........................................................21Delivery Tube - No Fertilizer ....................................21Delivery Tube - with Fertilizer...................................22Install Drop Tubes (all Kits) ......................................22

Install SMV Reflector.......................................................23Install Wind Shields .........................................................23Closeout ..........................................................................23

Operations.............................................................................24Loading Seed ..................................................................24

Small Seeds Box Loading ........................................24Small Seeds Rate............................................................24

Small Seeds Rate Calibration ..................................25Small Seed Tube Plugs...................................................27

Seed Rate ..............................................................................28Maintenance..........................................................................30

Small Seeds Box Clean-Out............................................30Chain Maintenance .........................................................30

Chain Slack ..............................................................30Lubrication.......................................................................31

Appendix ...............................................................................32Metric Rate Charts, Small Seeds Box .............................32Torque Values .................................................................34Abbreviations...................................................................35Part Lists .........................................................................35

Existing Parts Affected .............................................35New Parts.................................................................36

Index ......................................................................................39

2017-08-08 Cover Index 133-322M

© Copyright 2008, 2012, 2017 All rights Reserved

Great Plains Manufacturing, Inc. provides this publication “as is” without warranty of any kind, either expressed or implied. While every precaution has beentaken in the preparation of this manual, Great Plains Manufacturing, Inc. assumes no responsibility for errors or omissions. Neither is any liability assumedfor damages resulting from the use of the information contained herein. Great Plains Manufacturing, Inc. reserves the right to revise and improve its productsas it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future.

Trademarks of Great Plains Manufacturing, Inc. include: AccuShot, Max-Chisel, Row-Pro, Singulator Plus, Short Disk, Swath Command, Terra-Tine, Ultra-Chisel, and X-Press.

Registered Trademarks of Great Plains Manufacturing, Inc. include: Air-Pro, Clear-Shot, Discovator, Great Plains, Land Pride, MeterCone, Nutri-Pro, Seed-Lok, Solid Stand, Terra-Guard, Turbo-Chisel, Turbo-Chopper, Turbo-Max, Turbo-Till, Ultra-Till, Whirlfilter, and Yield-Pro.

Brand and Product Names that appear and are owned by others are trademarks of their respective owners.Printed in the United States of America

133-300A, 133-301A, 133-302A, 133-319A, 133-320A and 133-321ATable of Contents Index 1

Important Safety Information

Look for Safety SymbolThe SAFETY ALERT SYMBOL indicates there is apotential hazard to personal safety involved and extrasafety precaution must be taken. When you see thissymbol, be alert and carefully read the message thatfollows it. In addition to design and configuration ofequipment, hazard control and accident prevention aredependent upon the awareness, concern, prudence andproper training of personnel involved in the operation,transport, maintenance and storage of equipment.

Be Aware of Signal WordsSignal words designate a degree or level of hazardseriousness.

DANGER indicates an imminently hazardous situationwhich, if not avoided, will result in death or serious injury.This signal word is limited to the most extreme situations,typically for machine components that, for functionalpurposes, cannot be guarded.

WARNING indicates a potentially hazardous situationwhich, if not avoided, could result in death or seriousinjury, and includes hazards that are exposed whenguards are removed. It may also be used to alert againstunsafe practices.

CAUTION indicates a potentially hazardous situationwhich, if not avoided, may result in minor or moderateinjury. It may also be used to alert against unsafepractices.

Prepare for Emergencies Be prepared if a fire starts

Keep a first aid kit and fire extinguisher handy.

Keep emergency numbers for doctor, ambulance, hospitaland fire department near phone.

Wear Protective Equipment Wear protective clothing and equipment.

Because prolonged exposure to loud noise can causehearing impairment or hearing loss, wear suitablehearing protection such as earmuffs or earplugs.

Because working on equipment safely requires your fullattention, avoid wearing entertainment headphones whileperform the installation.

Be Familiar with Safety Decals Read and understand “Safety Decals” in the Operator

manual.

Read all instructions noted on the decals.

Keep decals clean. Replace damaged, faded and illegibledecals.


133-300A, 133-301A, 133-302A, 133-319A, 133-320A and 133-321ATable of Contents Index Important Safety Information 2

Avoid High Pressure FluidsObserve normal precautions for hitch hydraulicconnections and disconnections. Escaping fluid underpressure can penetrate the skin, causing serious injury.

Avoid the hazard by relieving pressure beforedisconnecting hydraulic lines.

Wear protective gloves and safety glasses or goggles whenworking with hydraulic systems.

If an accident occurs, seek immediate medical assistancefrom a physician familiar with this type of injury.

Practice Safe Maintenance Understand procedure before doing work. Use proper

tools and equipment. Refer to this manual for additionalinformation.

Work in a clean, dry area.

Lower the drill, put tractor in park, turn off engine, andremove key before performing maintenance.

Make sure all moving parts have stopped and all systempressure is relieved.

Disconnect battery ground cable (-) before servicing oradjusting electrical systems or before welding on drill.

Inspect all parts. Make sure parts are in good conditionand installed properly.

Remove buildup of grease, oil or debris.

Remove all tools and unused parts from drill beforeoperation.

Safety At All Timess Thoroughly read and understand the instructions in this

manual before operation. Read all instructions noted on thesafety decals.

s Be familiar with all implement functions.

s Operate machinery from the driver’s seat only.

s Do not leave implement unattended with tractor enginerunning.

s Wear snug-fitting clothing to avoid entanglement withmoving parts.Introduction



Introduction

Description of UnitThese field-installed kits add small seeds plantingcapability to specific 2004 or later 40-foot 3-section drills.There are separate kits for drills with and without fertilizercapability. There are separate kits for each row spacing.

Compatible DrillsDrills manufactured in 2004 or later (which includes all3S-4000HD and 3S-4000HDF models) are compatiblewith these kits. Drills manufactured earlier, may not havemount fittings for key components.

Refer to Figure 1, which depicts the left-hand drill section. Components on center and right-hand sections are similar.

Before installing any of these kits, inspect the main frameof any drill section.

• The right-hand front corner of the frame must have arectangular gusset plate with holes (ifright-side-drive Fertilizer is installed, this is under theFertilizer drive).

• Mid-frame, the clutch bearing plate must have alower bearing opening , and idler slot (ifright-side-drive Fertilizer is installed, a bearing and idler occupy these openings).

Compatible Kits

Each kit updates one drill.

Document Family

If your Seed Rate, Operator and/or Parts manuals aredated prior to 2008, check the Great Plains web site, orcheck with your Great Plains dealer, for updates.

The information in this manual is current at printing.Some parts may change to assure top performance.

2004+ 2003-

1

3

2

U

DF

B

L

R

Figure 1:Left-Hand Section Main Frame

27439

1

2 3

PartNumber

Descriptionand Compatible Drill Model

133-300A 3S-4000 7.5" SMALL SEEDS BUNDLfor: 3S-4000-6375, 3S-4000HD-6375

133-301A 3S-4000 6" SMALL SEEDS BUNDLfor: 3S-4000-7806, 3S-4000HD-7806

133-302A 3S-4000 10" SMALL SEEDS BUNDLfor: 3S-4000-4810, 3S-4000HD-4810

133-319A 3S-4000F 7.5" SMALL SEEDS BNDLfor: 3S-4000F-6375, 3S4000HDF-6375

133-320A 3S-4000F 6" SMALL SEEDS BNDLfor: 3S-4000F-7806, 3S4000HDF-7806

133-321A 3S-4000F 10" SMALL SEEDS BNDLfor: 3S4000HDF-7806, 3S4000HDF-4810

133-322M Installation, Operation and Maintenance(this document)

195-067M 3S-4000HD/4000HDF Operator Manual

195-067P 3S-4000HD/4000HDF Parts Manuala

a. For correct Small Seeds information, update any 195-067P and 195-242P Parts Manuals dated prior to 2008.

195-325B Multiple Drill Family Seed Rate Manualb

b. 195-325B replaces 195-067B and 195-242B.

195-394M 3S-4000/4000F Operator Manualc

c. 195-394M replaces 195-242M-A.

195-242P 3S-4000/4000F Parts Manuala


133-300A, 133-301A, 133-302A, 133-319A, 133-320A and 133-321ATable of Contents Index Introduction 4

Using This ManualThis manual familiarizes you with safety, assembly,operation, adjustments and maintenance. Follow therecommendations to help ensure safe and efficientoperation.

DefinitionsThe following terms are used throughout this manual.

Paragraphs in this format provide useful informationrelated to the current topic.

Liability, Economic and Results Risks:Paragraphs in this format present a crucial point of informationrelated to the current topic. Read and follow the directions to:remain safe, avoid serious damage to equipment and ensuredesired field results.

Right-hand and left-hand asused in this manual aredetermined by facing thedirection the machine willtravel while in use unlessotherwise stated.

An orientation rose (shown atright) depicts Up, Right, Back,Down, Left and Front.

Call-Outs

Owner AssistanceIf you need customer service or repair parts, contact aGreat Plains dealer. They have trained personnel, repairparts and equipment specially designed for Great Plainsproducts. Your machine’s parts were specially designedand should only be replaced with Great Plains parts.

Record your small seeds option kit model number herefor quick reference:

Model Number:__________________________

Further AssistanceFor additional help with understanding these assemblyinstructions or for any other assembly or setup relatedquestions, please contact our service department at thefollowing address:

Great Plains Service Department1525 E. North St.

P.O. Box 5060Salina, KS 67402-5060

Or call us at (800) 270-9302 to speak over the phonewith a service representative.

Copies of this machine’s operator manual are availableby mail or online. Please visit www.greatplainsag.comand follow the product link for information on yourmachine, or use the QRC code below to view our onlinepublications.

Figure 2:3S-4000 Drill

18824

R

L

U

DF

B

L

R

Single-digit callouts identify components in the currently referenced Figure or Figures. These numbers may be reused for different items from page to page.

to Two-digit callouts in the range 11 to 32 reference existing parts removed and reused. They are listed on page 36.

and on Three-digit callouts in the range 101 and on reference new parts from the new parts list beginning on page 37. The descriptions match those on the parts, cartons, bags or item tags, as well as descriptions your updated Parts Manual.

U

DL

R

B

F

1

11 32

101



Installation Instructions

Before You StartMost accidents are the result of negligence andcarelessness, usually caused by failure of the operator tofollow simple but necessary safety precautions. Allow noone to install the small seeds option before carefullyreading this manual.

Some fasteners may be loosely assembled. Removethem before mounting that component. Due to evolvingmanufacturing practices, some sub-assemblies mayalready be completely pre-assembled. If so, check thatfasteners are tight, and skip the unneeded assemblysteps.

Tools Required• Basic hand tools, including hose clamp pliers

• Drill and 11/32 inch, Q, or 8.3 mm drill bit

• Scaffold or ladderTorque values for fasteners are shown on page 35.

1. Read and understand “Important SafetyInformation” starting on page 1.

2. Ensure drill is compatible with kit. See page 3.

Prepare Drill3. If the drill to be updated has a Fertilizer box, clean

out the box per the instructions in the current drillOperator Manual.

4. Position the drill in a well lighted location suitable forthe installation. A clear surface beneath makes iteasier to recover any dropped parts.

5. Unfold the drill.

Refer to Figure 3

6. Install any parking stands provided with the drill.

7. Lower the drill.Lower the openers.

Other Options8. If also installing any main seed box options, or

walkboard ladders, install them before Small Seeds.If this is a new delivery, defer installation of presswheels and other row unit options until after installingSmall seeds. If also installing markers, install themafter Small Seeds.

9. Swing down the walkboard laddersa (if installed).

a. If the drill has only steps, as depicted in Figure 3, convenient swing-down ladders are available for field installation as kit 195-095A.

Negative Tongue Weight:Drill must be hitched to a tractor, or fully lowered, with anyparking stands installed, before commencing work. Theunfolded drill can have a negative tongue weight of up to 1000pounds.

Falling Hazard:Installation of the Small Seeds option reduces clearance abovethe walkboard. Drills with Small Seeds installed require morecaution when working on their walkboards.

Figure 3:Drill Parking Stand

15565

U

DB

F

R

L


133-300A, 133-301A, 133-302A, 133-319A, 133-320A and 133-321ATable of Contents Index Installation Instructions 6

Remove Seed Box Hardware Older drills may have washers instead of flanged

bolts and flanged nuts. If so, save these washers aswell. They are re-used.

Left-Hand Section HardwareS/N All

Refer to Figure 4

10. Remove and save two pairs of: 803-169C NUT HEX FLG. LOCK 1/2-13 PLT. 802-203C HFSS 1/2-13X1 1/2 GR5

and one each: 119-190D HANDLE 248-251D MANUAL PAK MOUNTING PLATE

Do not further disassemble the manual pak .

On some drills, this pak assembly may be mountedelsewhere, and does not need to be removed for installation of Small Seeds.

Right-Hand Section HardwareS/N All

Refer to Figure 5


and one: 119-190D HANDLE

Center Section HardwareS/N YY3076-

Refer to Figure 6


four pairs (8 total): 804-016C WASHER FLAT 1/2 SAE PLT

and two: 150-138D 12’ EWNT LIGHT BRACKET

Do not further disassemble the lights . Their cablesmay be left connected if there is convenient locationto position them during the remainder of theinstallation.

2626 23

23

19

11

U

DF

B

L

R

Figure 4:Left-Hand Section Hardware

27431

2623

1119

19

26

26 23

23

11

U

DF

B

L

R

Figure 5:Right-Hand Section Hardware

27431

2623

11

26

14

29 1423

U

DF

B

L

R

Figure 6:Center Section Hardware

27431

2623

29

14

14



Center Section HardwareS/N YY3077+

Refer to Figure 18.

13. At the left-hand end, remove and save four pairs of: 802-004C HHCS 1/4-20X3/4 GRD5 804-075C WASHER FLAT 1/4 USS PLT 804-006C WASHER LOCK SPRING 1/4 PLT 803-006C NUT HEX 1/4-20 PLT

14. Unplug and remove one ASSEMBLY, RED LAMP

NOTE:The lamp does not need to be removed from themounting bracket.

15. Remove two pair (4 total): 802-203C HFSS 1/2-13X1 1/2 GR5 803-169C NUT HEX FLG. LOCK 1/2-13 PLT.

16. Unplug and remove one: ASSEMBLY, AMBER LAMP

NOTE:The lamp does not need to be removed from themounting bracket.

17. Remove one: 151-454D .25 X 5.22 X 1.93- BOLT 0.5 SHIM

18. Repeat the procedure to remove the componentsfrom the other end of the center section.

26

36

15 3521

30

2724

23

26

36

15 3521

30

2724

23

Figure 7:Center Section

68437

21302724

35

2326

36

15



Install Mounts and Meter DrivesLeft-Hand MountsBegin with the left-hand section.

Refer to Figure 8

19. At the lower rear left-hand corner of the seed boxside wall , remove one set:

803-020C NUT HEX 1/2-13 PLT 804-015C WASHER LOCK SPRING 1/2 PLT 802-034C HHCS 1/2-13X1 1/4 GR5

These fasteners are not re-used.

20. Select one new: 133-158H SML SDS LH MOUNT WLDM

two sets new: 802-034C HHCS 1/2-13X1 1/4 GR5 804-015C WASHER LOCK SPRING 1/2 PLT 803-020C NUT HEX 1/2-13 PLT

21. Position the mount over the lower holes anddrop the two bolts in the holes to verifyalignment. Add a lock washer and spin on anut , finger tight.

22. Select two sets new: 802-203C HFSS 1/2-13X1 1/2 GR5 803-169C NUT HEX FLG. LOCK 1/2-13 PLT.

23. Using a flanged bolt and flanged lock nut ,secure the top end of the mount to the left-handrear corner of the main seed box where the handles,manual pak or lights were formerly mounted on thebox.

24. Tighten all fasteners to torque specifications.

The handles, manual pak and lights are notre-installed at this time.

25. Repeat step 19 through step 24 for the center andright-hand drill sections.

110

U

DB

F

R

L

125141

134

1

25

2822

136

127

Figure 8:Left-Hand Small Seeds Mount

27432

1252822

110

12528

134

110125

141134

127136

128 136110



Install Meter DrivesRefer to Figure 9

26. At the lower rear right-hand corner of the seed boxside wall , remove one each:

803-020C NUT HEX 1/2-13 PLT 804-015C WASHER LOCK SPRING 1/2 PLT 802-034C HHCS 1/2-13X1 1/4 GR5

These fasteners are not re-used.

27. Select one new: 133-163K 2600 SMLSDS RH MOUNT&DRIVE ASY

and two sets new: 802-034C HHCS 1/2-13X1 1/4 GR5 804-015C WASHER LOCK SPRING 1/2 PLT 803-020C NUT HEX 1/2-13 PLT

28. Position the mount over the lower holes anddrop the two bolts in the holes to verifyalignment. Add a lock washer and spin on anut , finger tight.

29. Select two sets new: 802-203C HFSS 1/2-13X1 1/2 GR5 803-169C NUT HEX FLG. LOCK 1/2-13 PLT.

30. Using a flanged bolt and flanged lock nut ,secure the top end of the mount to the right-hand rear corner of the main seed box where thehandles or lights were formerly mounted on the box.

31. Tighten all fasteners to torque specifications.

The handles and lights are not re-installed at this time.

32. Repeat step 26 through step 31 for the center andright-hand sections.

Secure Wind ShieldsRefer to Figure 10

33. If the wind shields are pre-installed on the seedcups, remove and save them, to prevent loss ordamage during seed box installation.

Squeeze the tabs at the top. Tilt the shield backwardand out. These are re-installed at step 135 onpage 24.

U

DL

R

B

F

111

125

141

134

2

127136

25

28

22

Figure 9:Install a Meter Drive

27433

2252822

111

125141134

111125

141134

127136

127 136111

Figure 10:817-806C Wind Shield

34582

150

U

DR

F

B

L150


133-300A, 133-301A, 133-302A, 133-319A, 133-320A and 133-321ATable of Contents IndexInstallation Instructions 10

Mount Seed BoxesStarting with the left-hand section:

Refer to Figure 11

34. Select one of the following, new: 133-153K 2600 SML SDS RH BOX ASY 6 IN 133-155K 2600 SML SDS RH BOX ASY 7.5 IN 133-157K 2600 SML SDS RH BOX ASY 10 IN

35. Select four sets of new: 802-388C HFS 3/8-16X1 GR5 803-014C NUT HEX 3/8-16 PLT 804-013C WASHER LOCK SPRING 3/8 PLT

36. Mount the box at the forward set of open holes in themounts and drives just installed.

37. Repeat step 34 through step 36 for the center andright-hand sections

Install Seed Box HardwareThe new guards mount under the old corner fittings. Ifthe removed and saved bolts and nuts are not of theflanged type, also re-install the washers removed withthem. The location of the washers is shown in theFigures, but without callout numbers.

Start with the left-hand section:

Outer End of Outer Section BoxS/N All

Refer to Figure 12, which depicts the left-hand section box.Select one saved:

119-190D HANDLEand if it was present, one saved:

248-251D MANUAL PAK MOUNTING PLATE

38. Select two sets saved: 803-169C NUT HEX FLG. LOCK 1/2-13 PLT. 802-203C HFSS 1/2-13X1 1/2 GR5

or HHCS bolts, flat washers and plain nuts.

39. For the outer end of the left-hand section box, selectone new:

123-491D HANDLE MOUNT LH CHAIN GUARD

40. For the outer end of the right-hand section box (notshown), select one new:

123-492D HANDLE MOUNT RH CHAIN GUARD

41. Install the guard . Position the manual pakmount (if any) and then the handle . Securewith bolts , nuts and washers (if any).

U

DL

R

B

F

129140

133

109108107

129

140

133

Figure 11:Mount a Small Seeds Box

27434

107108109

129133140

U

DL

R

B

F102

26

23

1126

Figure 12:Outer End of Outer Section Box

27435

11

19

2623

102

103

10219 11

23 26



Inner End of Outer Section BoxS/N All

Refer to Figure 13, which depicts the left-hand section box.

42. Select two sets saved: 803-169C NUT HEX FLG. LOCK 1/2-13 PLT. 802-203C HFSS 1/2-13X1 1/2 GR5

or HHCS bolts, flat washers and plain nuts.For the inner end of the left-hand section box, selectone new:

123-492D HANDLE MOUNT RH CHAIN GUARD

43. For the inner end of the right-hand section box (notshown), select one new:


44. Position guard on the small seed box drive mount.Secure with bolts , nuts and washers (if any).

45. Repeat step 42 through step 42 for the right-hand ofthe other outer seed box.

Center Section HardwareS/N 3076-

Refer to Figure 14

46. Install two: 150-138D 12’ EWNT LIGHT BRACKET 802-203C HFSS 1/2-13X1 1/2 GR5 803-169C NUT HEX FLG. LOCK 1/2-13 PLT.

four pairs (8 total): 804-016C WASHER FLAT 1/2 SAE PLT

Connect lights to the machine wiring harness.

U

DL

R

B

F

103

26

23

Figure 13:Inner End of L-H Section Box

27435

2623

103

102

23 26

26

14

29 1423

U

DF

B

L

R

Figure 14:Center Section Hardware

27431

142326

29



Center Section Lights and HardwareS/N YY3077+

Refer to Figure 15

Select two:(31) 171-059D 3/16 LIGHT PLATE MIN TILLand four new:(21) 802-004C HHCS 1/4-20X3/4 GR5(12) 804-075C WASHER FLAT 1/4 USS PLT(138) 804-006C WASHER LOCK SPRING 1/4 PLT(131) 803-006C NUT HEX 1/4-20 PLT

Install a light plate (31) to the existing light bracket(A) on the small seeds box.

NOTE:A red lamp should still fastened to the light plate.

Fasten with two bolts (21), flat washers (12), lockwashers (138), and nuts (131).

Repeat the procedure to install the other red lampassembly.

The light plates may need to be adjusted to fit withthe hose layout of the small seeds box. Use thenecessary combination of holes on the bracket andplate.

NOTE:The red lights, when installed, must not be more than5 feet apart.

47. Install one each on right-hand end of the centersection:

ASSEMBLY, AMBER LAMP 151-454D .25 X 5.22 X 1.93- BOLT 0.5 SHIM 123-492D HANDLE MOUNT RH CHAIN GUARD

48. Install two pair (4 total): 802-203C HFSS 1/2-13X1 1/2 GR5 803-169C NUT HEX FLG. LOCK 1/2-13 PLT.

49. Install the chain guard , the shim , and amberlamp assembly , to the small seeds box mount.Secure with hex flange bolts and hex flangenuts .

50. Repeat the procedure to install the components onthe left-hand side of the center section. The partnumber for the left-hand chain guard is:


51. Plug all four lights into the main harness.

31

A138

131

126

12

Figure 15:Light Bracket Extension

68381B

23

36

12

26

15

Figure 16:Center Section - Right-Hand End

68381C

361512

2326

12 1536

2326

13



Install Meter Shaft ChainsStart with the left-hand section.

Refer to Figure 17, which is depicted with obscuring parts removed. Gray arrows show direction of chain motion.

52. Select one new: 136-104D CHAIN RL #40 62 PITCHES

53. Route chain around lower jackshaft drivingsprocket, around upper final meter shaft sprocket,and forward of idler .

Make sure chain clip opening faces away fromdirection of chain motion. See Figure 42 on page 31.

54. Engage idler arm and tighten bolt when longestspan of chain has 1/4 inch (6 mm) slack.


Install Forward ComponentsFront component installation is different for each drillsection, and is different for drills with and without theFertilizer option. The front Small Seeds drive assembly isinstalled in all cases.

Page 14 step 56: If the drill does not have fertilizer, yourSmall Seeds kit includes an empty Fertilizer drive mount,bearing, jackshaft, sprockets, idler and chain for eachdrill section.

Page 19 step 89: With Fertilizer installed, the SmallSeeds front drives mount on top of the existing Fertilizerdrive mounts. The jackshaft is already installed, and onlyrequires adding a sprocket to each jackshaft.

U

DL

R

B

F

115

1

2

Figure 17:Final Drive Chain

27436

133

112

1

2



Front Drives without FertilizerClutch Bearing Plate Components

Start with the left-hand section. This work is similar for allsections.

Refer to Figure 18, which depicts the clutch bearing plate with numerous components removed for clarity.

56. Select one new: 822-119C BRG 7/8HEXX2.05OD SPH

and two sets new: 822-032C FLANGETTE 52 MST 802-282C RHSNB 5/16-18X1 GR5 804-009C WASHER LOCK SPRING 5/16 PLT 803-008C NUT HEX 5/16-18 PLT

57. Sandwich the bearing between theflangettes , and mount the assembly at the lowopen flangette hole of the clutch bearing plate.Mount from the left, with the bolts inserted fromthe right. Secure with lock washers andnuts .

58. Select one each new: 802-041C HHCS 1/2-13X3 1/2 GR5 817-025C NO. 40 12T IDLER SPKT. 804-015C WASHER LOCK SPRING 1/2 PLT

two each new: 803-036C NUT HEX JAM 1/2-13 PLT 804-113C WASHER FLAT 1/2 USS HARD PLT

59. Slide idler onto the bolt , secured by a jamnut spun on finger tight. Add flat washer .

From the right-hand side, insert the idler assemblyinto the forward idler slot of the clutch bearingplate. Loosely secure it with another flat washer ,lock washer and the second jam nut .


U

DF

B

L

R

Figure 18:Clutch Bearing Plate

27440

126

153

1

132

152

139

128

2

149128

128

143

141135

153

152128139132

153152

1

128139

132

126149141

135143

149 126135 143

2

143141 135



Refer to Figure 19, which depicts the clutch bearing plate with numerous components removed for clarity.

Jackshafts are different lengths for each drill section.These steps are otherwise identical. Start with theleft-hand drill section.

61. Select one each new:For the left-hand section, the 90 inch shaft:

195-272D HEX SHAFT 7/8,4000 FERT JS LHFor the center section, the 72.75 inch shaft:

195-270D HEX SHAFT 7/8,4000 FERT JS CTRFor the right-hand section, the 48.5 inch shaft:

195-271D HEX SHAFT 7/8,4000 FERT JS RH

62. Select one each new: 805-180C PIN ROLL 1/4 X 1 1/2 LG PLT

63. From the right-hand side of the clutch bearing plate,insert the shaft end with the pin holes through thebearing installed at step 57.

64. Drive the roll pin through the hole nearest theend of the shaft.

Leave the other pin hole open until step 85. Theshaft needs to slide aside to mount the Small Seedsdrive and accept the other end of the shaft.

65. Select two new: 804-061C WASHER MACH 1.50 X 1.00 X 18GA

Slide them onto the shaft from the right-hand side.

66. Select one new: 808-256C SPKT 40C23 X 7/8 HEX BORE

Orient it with the side having the wider hub to drill left(toward the clutch bearing plate). Slide it onto theshaft from the right-hand side.

Refer to Figure 20

67. Select one new: 808-194C SPKT 40B22 7/8 HEX BORE & SS

Orient it with the set screw hub to drill right and slideit onto the shaft. Use the set screws to temporarilysecure it about 10 inches (25 cm) from the end of theshaft.


U

DF

B

L

R

120

1

2

147

142

144

119118

Figure 19:Jackshaft at Clutch Bearing Plate

27441

120

118

119

144

1

144

2

142

U

DF

B

L

R

146

Figure 20:B22 Sprocket on Jackshaft

27441

147

146



Front Drive, Left-Hand Section

Refer to Figure 21

69. Select one each new: 195-269H 40’-3S FERT DRIVE WELDMENT RH 802-034C HHCS 1/2-13X1 1/4 GR5 804-015C WASHER LOCK SPRING 1/2 PLT 803-020C NUT HEX 1/2-13 PLT

70. Position the weldment at the front right-handcorner of the mainframe. Align the right-hand edge ofthe weldment against the frame side rail, andposition the front right-hand base hole over thehole in the frame web.

Insert a bolt through rear hole of theweldment base and frame gusset . Loosely securewith a lock washer and nut .

71. Select one each new: 133-324K 2600 SMLSDS RH MOUNT&DRIVE ASY

four each new: 804-113C WASHER FLAT 1/2 USS HARD PLT

and three sets new of: 802-034C HHCS 1/2-13X1 1/4 GR5 804-015C WASHER LOCK SPRING 1/2 PLT 803-020C NUT HEX 1/2-13 PLT

72. Position the Small Seeds drive on top of thefertilizer weldment and secure with bolts ,flat washers , lock washers and nuts .The front left-hand bolt in the slotted hole takes twoflat washers , one under bolt head and oneabove lock washer.

Refer to Figure 22 (drive shown without drill frame)



74. At the installed Small Seeds drive, sandwich thebearing between the flangettes , and mountthe assembly at the forward open flangette hole ofthe fertilizer weldment . Mount from the left-hand(outside the drive), with the bolts inserted fromthe right. Secure with lock washers andnuts .

U

DF

B

L

R117

141

125

134

2

1

3

112

143

Figure 21:Small Seeds Drive

Left-Hand Section w/o Fertilizer

27437

117125141134

117

1

125 23

141 134

112

143

125141134

U

DF

B

L

R

Figure 22:Small Seeds Input Bearing

27442

1534

132

152

139

128

112117 125

143 141 134

143

153

152128139132

153 1524

117128

139132



Front Drive, Center and Right-Hand Sections

Refer to Figure 23

75. Select one each new: 195-269H 40’-3S FERT DRIVE WELDMENT RH 802-034C HHCS 1/2-13X1 1/4 GR5 804-015C WASHER LOCK SPRING 1/2 PLT 803-020C NUT HEX 1/2-13 PLT

76. Position the weldment at the front right-handcorner of the mainframe. Align the right-hand edge ofthe weldment against the frame side rail, andposition the right-hand rear hole over a hole in theframe gusset. Make sure both left-hand base holesare on either side of the front frame tube (to acceptU-bolt at step 79). Insert a bolt through the right-hand rear holeof the weldment base. Loosely secure with a lockwasher and nut .

77. Select one each new: 133-324K 2600 SMLSDS RH MOUNT&DRIVE ASY 806-060C U-BOLT 1/2-13 X 6 1/32 X 7 1/4 802-034C HHCS 1/2-13X1 1/4 GR5

and three sets new of: 804-113C WASHER FLAT 1/2 USS HARD PLT 804-015C WASHER LOCK SPRING 1/2 PLT 803-020C NUT HEX 1/2-13 PLT

78. Position the Small Seeds drive on top of thefertilizer weldment .

79. Install the U-bolt up through the left-hand sideholes of the drive and loosely secure with flatwashers , lock washers and nuts . Insertbolt through washer , and right-hand forwardhole of drive (not visible in Figure). Add lockwasher , another flat washer , and nut .Tighten all nuts.

Refer to Figure 24 (drive shown without drill frame)



81. At the Small Seeds drive, sandwich the bearingbetween the flangettes , and mount theassembly at the forward open flangette hole of thefertilizer weldment . Mount from the left-hand(outside the drive), with the bolts inserted fromthe right. Secure with lock washers andnuts .

U

DF

B

L

R

117

141

125134

1

112

145

141

134

143


Center Section w/o Fertilizer

27438

117125141134

117

1

125 1

141 134

112145125

143141134

U

DF

B

L

R

Figure 24:Small Seeds Input Bearing

27442

1534

132

152

139

128

112117

145

143 141 134125 143

141 143 134

153

152128139132

153152

4

117128

139132



82. Repeat step 75 through step 81 for the right-handdrill section.

Align Jackshafts

Start with the left-hand drill section.

Refer to Figure 25, which depicts drill center section

83. Slide the left-hand end of the jackshaft into theinput bearing of the Small Seeds drive. Move theshaft toward the left-hand side until travel is stoppedat the far end of the shaft by the roll pin reaching thenew bearing in the clutch plate.

Refer to Figure 26. Striped arrows show chain direction.

84. At the clutch plate, slide the jackshaft input sprocket and washers left, until they reach the new

bearing.

85. Select one each new: 805-180C PIN ROLL 1/4 X 1 1/2 LG PLT

Drive the roll pin into the shaft just to theright-hand side of the sprocket .

86. Select one new: 136-064D CHAIN RL #40 51 PITCHES

Install chain from clutch output above, behindidler , to jackshaft input sprocket . Orientchain clip per Figure 42 on page 31. Tighten idlerwhen longest span of chain has 1/4 inch (6 mm)slack.


88. Skip to step 107 (step 89 through step 106 are fordrills with Fertilizer).

U

DF

B

L

R

1

2

Figure 25:Small Seeds Jackshaft Install

27443

12

U

DR

L

F

B

Figure 26:Jackshaft Input Sprocket

27444

147

144

113

149

147

144144

147

113

149 147



Front Drives with FertilizerStart with the left-hand drill section, at the clutch bearingplate.

Refer to Figure 27

89. Locate the fertilizer jackshaft input sprocket belowthe clutch output sprocket.

90. Loosen the idler .

91. Drive out and save: 805-180C PIN ROLL 1/4 X 1 1/2 LG PLT

Refer to Figure 28, which depicts corner drive mounting for center and right-hand drill sections.

92. At the right-hand front corner of the frame, locate: 195-273S 40’-3S FERT DR SUBASSY LH

Loosen and relax all idlers.

93. Loosen set screws, remove and save: 808-143C SPKT 40B12 7/8 HEX BORE W/SS

94. Slide fertilizer jackshaft left, out of fertilizerassembly .

95. Select one new: 808-194C SPKT 40B22 7/8 HEX BORE & SS

Orient it with the set screw hub to drill right-hand andslide it onto the jackshaft . Use the set screws totemporarily secure it about 10 inches (25 cm) fromthe end of the shaft. Do not re-install the shaft at thistime.

In the next step, leave the mounting bolt at right-handrear of the fertilizer drive assembly (not visible infigure). It keeps the drive in place and correctlyaligned.

96. Remove and save the 2 or 3 sets of front andleft-hand fasteners that secure the fertilizer driveassembly to the frame. These fasteners may bebolts and/or U-bolts, depending on drill section.

U

DR

L

F

B

Figure 27:Fert. Jackshaft Input Sprocket

27444

12

31

1

2

31

U

DF

B

L

R

18

32

3

146

5

4

Figure 28:Add Sprocket to Jackshaft

27445

18

32

318

146

3

4

518



Refer to Figure 29, which depicts the fertilizer drive weldment elevated and without fertilizer drive components.

97. Select one new: 133-324K 2600 SMLSDS RH MOUNT&DRIVE ASY

Position the Small Seeds drive over the Fertilizerdrive , and align the mounting holes.

98. Select the 2 or 3 sets of saved fasteners fromstep 96. Re-install them.

99. For the left-hand drill section only, select one set newof:

802-034C HHCS 1/2-13X1 1/4 GR5 804-113C WASHER FLAT 1/2 USS HARD PLT 804-015C WASHER LOCK SPRING 1/2 PLT 803-020C NUT HEX 1/2-13 PLT

Install these at the left-hand rear mounting hole ofthe Small Seeds drive.

Refer to Figure 30

100.Slide the left-hand end of the jackshaft into theinput bearing of the Fertilizer and Small Seeds drive.Move the shaft toward the left-hand side until travelis stopped at the far end of the shaft by the roll pinreaching the bearing in the clutch bearing plate.

101.Select the saved: 808-143C SPKT 40B12 7/8 HEX BORE W/SS

Orient the set screw hub to the left, and place thesprocket back on the jackshaft . Align it with theFertilizer drive sprocket it drives and tighten the setscrews. Re-mount the chain.

102.Retighten idlers in Fertilizer drive assembly.

U

DF

B

L

R

141

125

134

112

18

143

6

6

6

6


Left-Hand Section with Fertilizer

27437

112

18

6

125143141134

U

DF

B

L

R

32

1

Figure 30:Small Seeds and Fertilizer

Input Sprockets

27447

1

32

32 1




103.At the clutch plate, slide the jackshaft inputsprocket and washers left, until they reach thebearing.

104.Select the saved: 805-180C PIN ROLL 1/4 X 1 1/2 LG PLT

Drive the roll pin into the shaft just to theright-hand side of the sprocket .

105.Tighten input idler when longest span of chain has1/4 inch (6 mm) slack.

106.Repeat step 89 through step 105 for the center andright-hand drill sections.

Small Seeds Drive ChainsThis and all remaining steps are the same with or withoutFertilizer installed. Start with left-hand drill section.

Refer to Figure 32. Striped arrow shows chain direction.

107.Loosen the set screws on: 808-194C SPKT 40B22 7/8 HEX BORE & SS

Slide it toward the right-hand side of the machineand align it in the same plane as the Small Seedsdrive input sprocket and idler.

108.Select one new: 136-078D CHAIN RL #40 52 PITCHES

109.Route chain around jackshaft output sprocket, SmallSeeds input sprocket and Small Seeds input idler.Make sure chain clip opening faces away fromdirection of chain travel, as shown in Figure 42 onpage 31.

110.Tighten set screws on output sprocket. Adjust chainslack to 1/4 inch (6 mm).

Figure 31:Fert. Jackshaft Input Sprocket

27444

U

DR

L

F

B

1

31

1

3131

1

U

DF

B

L

R

146

2

114

Figure 32:Small Seeds Drive Input

27448

146

2

114




111.Select one new: 136-154D CHAIN RL #40 214 PITCHES

112.Route chain around Small Seeds drive outputsprocket and meter drive input sprocket . Makesure chain clip opening faces away from direction ofchain travel, as shown in Figure 42 on page 31.

Chain routes forward of and under both 17-toothidlers .

113.Adjust idlers for 1/2 inch (13 mm) slack in longest(bottom) span of chain.

114.Repeat step 111 through step 113 for center andright-hand drill sections.

Install Seed TubesSeed tube installation is different for drills with andwithout the Fertilizer option. With Fertilizer installed, therow unit frame opening behind the main seed tube isoccupied by the fertilizer drop tube. A side delivery tubeis used for Small Seeds in that case.

115.If Fertilizer is installed, skip to step 120 on page 23.

Delivery Tube - No FertilizerStart with the left-most row unit.

Refer to Figure 34

116.Select one each new: 123-939H SMALL SEEDS TUBE WELDMENT

and two new: 801-002C SCREW HEX SLT10-16X1/2P.THD CT

117.Insert the long end of the delivery tube throughthe row unit frame hole in between the T-handleslot and the main seed tube hole. The bent lowersection of the delivery tube angles forward. Securetube with two screws .

118.Repeat step 116 and step 117 for each row unit.

119.Skip to step 124.

Figure 33:Small Seeds Drive Output Chain

27449

U

DF

B

L

R 116

33

12

116

1161 2

3

3

U

DB

F

R

L

1

104

122

Figure 34:Small Seeds Delivery Tube

without Fertilizer

27470

104

122

1041

122



Delivery Tube - with FertilizerStart with the left-most row unit.

Refer to Figure 35, which does not depict the fertilizer delivery tube in the hole.

120.Select one each new: 133-128H SGS SIDE DELIVERY TUBE 802-427C HFS 3/8-16X3 3/4 SPTHD 803-209C NUT FLANGE LOCK 3/8-16 PLT

121.Orient the side tube weldment with the delivery tubeto the left-hand side of the row unit, and the mountahead of the fertilizer delivery tube hole .

122.Insert a bolt through mount and the row unitframe at hole . Secure with lock nut .

123.Repeat step 120 through step 122 for each row unit.

Install Drop Tubes (all Kits)Start with the left-most row unit.

Feeder cups may not be directly above the row unit towhich their hose connects.

Refer to Figure 36

124.Select one new: 816-358C SGS HOSE 122 RIBS

and two new: 800-321C HOSE CLAMP NO.12 3/4 ID

The end of the hose with the shorter smooth section isthe top end.

125.Open a hose clamp and place it over the topend of the hose . Move the clamp down to thestart of the ribbed section.

126.Slide the top of the hose onto the drop tubeof the fluted feed cup for that row, so that the hosecompletely covers the straight portion of the exittube. Open the clamp and position it about1/4 inch (6 mm) above the bottom of the exit tube.

127.Open a hose clamp and place it over the otherend of the hose . Move the clamp up from theend of the hose.

128.Slide the bottom end of the hose onto the top ofthe delivery tube , so that it completely covers theexposed portion of the tube. Open the clamp andposition it about 1/2 inch (13 mm) from the end of thehose.

129.Repeat step 124 through step 128 for each row unit.

U

DF

B

L

R

130

3

137

106

2

Figure 35:Small Seeds Side Delivery Tube

with Fertilizer

27450

106130137

2

1303 137

U

DB

F

R

L

148

5

121

121

4

Figure 36:Small Seeds Drop Tubes

27470

148

121

121148

148 4

121148

1485



Install SMV ReflectorThe Small Seeds box obscures the original Slow MovingVehicle decal on the main seed box. Your kit includes anew reflector to be mounted on the walkboard.

All pre-2008 drills, and some 2008 drills, do not alreadyhave SMV mounting holes in the walkboard, and requiredrilling.

Refer to Figure 37

130.Select one new: 133-070D 3000 SMV MOUNTING BLADE

131.If the walkboard already has SMV mounting holes,skip to step 133.

132.Use the two end mounting holes in the blade to markholes to drill - center drill section, center of rear faceof walkboard . Balance the vertical position toplace each hole the same distance from the top andbottom edge of the walkboard. Drill holes for5/16-18in clearance, nominally an 11/32 inch, lettersize Q, or an 8.3 mm drill bit.

133.Select two sets new: 802-007C HHCS 5/16-18X3/4 GR5 804-009C WASHER LOCK SPRING 5/16 PLT 803-008C NUT HEX 5/16-18 PLT

Secure the blade to the walkboard with twobolts , lock washers and nuts .

134.Select one new: 818-055C DECAL SLOW MOVING-GALV. BACKED

and two sets new: 802-004C HHCS 1/4-20X3/4 GR5 804-006C WASHER LOCK SPRING 1/4 PLT 803-006C NUT HEX 1/4-20 PLT

Secure the reflector to the blade with twobolts , lock washers and nuts .

Install Wind ShieldsRefer to Figure 38

135.For each row, select one new: 817-806C SMALL SEEDS CUP WIND SHIELD

Insert the bottom edge of the rear face of theshield into the funnel. Snap the ears into theinside vertical grooves of the meter cup.

Closeout136.See Operator Manual. Hitch and raise drill. Lower

the openers. Rotate gauge wheels. Check that alldrives and box meter shafts are rotating freely.

137.Close lids on all seed boxes.

138.See page 25. Set Small Seeds rate adjusters to 0 todiscourage pest entry.

139.Add this manual to the Manual Pak enclosure, orreplace the existing Seed Rate manual with anupdated manual.

140.Review the Operations section of this manual beforeplanting small seeds.

Figure 37:SMV Placard Mount

20103

U

DF

B

L

R

139

124

105 1

132

131138

151123

105

1

124139132

105 1

124 139 132

Figure 38:817-806C Wind Shield Installed

34582

150

U

DR

F

B

L

151

123138131

151 105123 138 131

150

150



Operations

Loading SeedSeed may be loaded in the field or prior to transport.Fully loaded with dense seed, the drill can weigh anadditional 8294 pounds (3762 kg). Include this weightwhen checking tractor capability.

The drill must be hitched for seed loading. Themainframe may be raised or lowered. Lowered placesthe walkboards closer to the ground, reducing effortwhen manually loading bagged seed. If equipped withladders, swing them down.

Small Seeds Box Loading1. If loading prior to transport, and calibration has not

yet been done, set Seed Rate Handles to 0. At 0, noseed can leak during transport.

2. Take all necessary materials safety precautions if theseed is treated.

3. Load seed evenly into seed boxes.

4. To reduce wear, remove main shaft drive chains formain seed boxes.

Fluted-feed materials, such as Small Seeds andFertilizer, do not require lubricants.

Small Seeds RateSeeding rate from the optional Small Seeds Attachmentis controlled entirely by seed rate handles on each smallseeds box. No sprocket changes are required, and smallseeds rate is unaffected by settings for main seed box.

Refer to Figure 39

To set Small Seeds rate, loosen the wing nut at eachhandle, and adjust the lever position. Tighten nut.

Figure 39Small Seeds Rate Handle

18511

1

2

1

2


133-300A, 133-301A, 133-302A, 133-319A, 133-320A and 133-321ATable of Contents Index Operations 26

Small Seeds Rate CalibrationDifferences will exist between the tested seed and fieldconditions used to generate the Small Seeds RateCharts, and your seed and conditions. To accuratelyachieve your target population, Great Plainsrecommends calibrating.

Perform the calibration with the drill raised for transport,but with the opener frames lowered (if the openers areraised, the clutches will disengage). Leave the tractorhitched for movement control. Block the tires not beingused in the calibration.

If you have previously calibrated your acremeter (seeOperator Manual), you can use it to tally acres.

1. Jack up the left-hand drive gauge wheel assemblyuntil the left-hand section is roughly level. Use blocksto ensure that the section cannot fall if the jackrelaxes, tips over or fails.

2. Rotate the gauge wheels and check that the drivesand seed cups are engaged, working properly andfree from foreign material. If not already done, setthe Small Seeds Rate Handle. If fertilizer is loaded,remove the fertilizer drive chain (unless you aresimultaneously calibrating fertilizer rate).

3. Clear the FIELD ACRES to 0000.0 on the electronicacremeter, unless you do not plan to rely on it for thecalibration.

4. Check that your gauge-wheel tires are265/70B16.5 NHS Skid Steer and properly inflated.See “Tire Inflation Chart” in Operator Manual.

5. Record the weight of one to three empty containerscollectively large enough to hold seed metered for6% of one acre.

6. Place several pounds of seed over three seed cupson the outside end of the left-hand drill box. Pulllower end seed hoses off of these drops at theopener end.

7. Turn gauge wheel several times to fill seed cups.Turn until seed drops to ground from each hose.

8. Place empty container(s) under the three hoses togather metered seed.

9. Turn gauge wheel until one acre is tallied onacremeter (130 wheel rotations). While turning,check that cups have ample seed coming into them.

10. Weigh metered seed. Subtract initial weight ofcontainer(s).

Crushing Hazard:You may be severely injured or killed by being crushed from afalling implement or openers. Always have transport locks inplace and frame sufficiently blocked up when working on thedrill.

For example:using a row spacing of:

7.5inrow count:

63you desire to plant alfalfa at:

10 pounds per acre;this corresponds to an initial Seed Rate Handle of:

50

For example:three 0.5 pound (8 oz.) containers weigh:

1.5 lbs

For example:the three containers weighed a total 2.2 lbs after test:

0.7 lbs net

NetWeight GrossWeight ContainerWeights–=

0.7 2.2 1.5–=



11. Divide the net seed weight by three. Multiply bynumber of openers on your drill to determine the totalof pounds-per-acre seeded.

12. The Seed Rate Handle scale is a percentage ofmeter opening, and is quite linear near scale center.Calculate a new scale setting based on the test.

You may want to repeat calibration procedure if yourresults varied greatly from the Seed Rate Chart, or ifyou must operate near the ends of the Seed Ratehandle scale (0-20 or 90-100).

13. Set the center and right-hand drill sections to matchthe now-calibrated left-hand section.

14. With calibration complete, Reinstall fertilizer chain (ifremoved), reconnect seed hoses, and lower gaugewheel to ground.

When drilling, check seeding rate by noting acres drilled,amount of seed added to drill and seed level in drill box.If you are seeding more or less than desired, adjust rateslightly to compensate for field conditions.

For example:a 7.5in drill has 63 rows:

14.7 lbs/ac

MeasuredRateNetWeight

3------------------------- RowCount=

14.70.73

------- 63=

For example:new scale:

34

NewScaleTargetRate

MeasuredRate---------------------------------- OldScale=

3410

14.7---------- 50=



Small Seeds Row Shut-Off

If alternate row spacing is required for small seeds,optional plugs are available to block flow inside the seedbox tray.

1. Clean-out seed. The seed box must be empty priorto inserting plugs. See “Small Seeds BoxClean-Out” on page 31.

2. Before installing plugs, inspect the seed boxes forexisting factory-installed plugs. These are blockingextra unused seed ports. You may want to identifythese plugs with an indelible marker.

3. Insert one plug at each row to shut off. Verify theseed hose path before inserting the plug, as somehoses do not make a strictly vertical drop to their rowunits.

4. Review seed rate settings and marker extensionprior to planting.

When removing plugs to restore rows to operation, besure to not disturb a factory-installed plug.

Small Seed Tube PlugsThis plug stops seed flow from the small seeds box atthe top of a seed tube. Order one per row to set inactive.

Description Part Number

SML SDS CUP PLUG 133-315H

Figure 40Small Seeds Tube Plug

27407



Seed Rate

Metric charts begin on page 33.

Alfalfa, Red Alsike, Crimson Clover

Kentucky Bluegrass,Fescue, Annual Rye Grass

Bermuda, Red Top, Lespedeza Unhulled,Sercia, Sand, Weeping Love Grass

Red & Sweet Clover, Lespedeza Hulled

Orchard Grass

Small Seeds Cup Lever Setting

0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100

Rows Seeding Rate in Pounds per Acre

6 inch 0 0.0 2.2 3.5 4.8 6.0 7.5 8.7 9.8 11.2 12.5 13.8 15.1 16.4 17.5 18.6 20.2 21.4 22.9 24.0 25.2

7.5 inch 0 0.0 1.8 2.8 3.9 4.8 6.0 7.0 7.9 9.0 10.0 11.1 12.1 13.2 14.0 15.3 16.2 17.2 18.3 19.3 20.3

10 inch 0 0.0 1.3 2.1 2.8 3.5 4.4 5.1 5.8 6.6 7.4 8.1 8.9 9.7 10.3 11.2 11.9 12.6 13.4 14.2 14.9


0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100


6 inch 0 0.0 0.2 1.2 1.9 2.7 3.3 4.1 4.6 5.2 5.8 6.3 6.8 7.3 7.8 8.3 8.8 9.2 9.7 10.0 10.5

7.5 inch 0 0.0 0.2 .9 1.5 2.2 2.7 3.3 3.7 4.2 4.6 5.1 5.5 5.9 6.3 6.7 7.0 7.4 7.7 8.1 8.4

10 inch 0 0.0 0.1 0.7 1.1 1.6 2.0 2.4 2.7 3.1 3.4 3.7 4.0 4.3 4.6 4.9 5.2 5.4 5.7 5.9 6.2


0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100


6 inch 0 0.0 0.7 1.1 1.7 2.6 3.3 4.1 5.0 5.9 6.6 7.2 7.8 8.4 9.0 9.5 10.2 10.9 11.6 12.2 12.9

7.5 inch 0 0.0 0.5 0.9 1.4 2.1 2.6 3.3 4.0 4.7 5.3 5.8 6.3 6.7 7.2 7.6 8.2 8.8 9.3 9.8 10.4

10 inch 0 0.0 0.4 0.6 1.0 1.5 1.9 2.4 3.0 3.5 3.9 4.2 4.6 4.9 5.3 5.6 6.0 6.4 6.8 7.2 7.6


0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100


6 inch 0 0.0 1.5 3.4 5.2 7.1 9.0 11.3 13.2 15.3 17.0 19.0 20.8 22.5 24.5 26.4 28.3 30.1 32.1 33.8 35.6

7.5 inch 0 0.0 1.2 2.7 4.2 5.7 7.2 9.1 10.6 12.3 13.7 15.3 16.7 18.1 19.7 21.2 22.7 24.2 25.8 27.2 28.6

10 inch 0 0.0 0.9 2.0 3.1 4.2 5.3 6.7 7.8 9.0 10.0 11.2 12.2 13.3 14.4 15.6 16.6 17.8 18.9 19.9 20.9


0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100


6 inch 0 0.0 0.0 0.3 0.7 .9 1.3 1.5 2.0 2.4 2.8 3.3 3.5 3.9 4.4 4.8 5.0 5.5 5.7 6.1 6.3

7.5 inch 0 0.0 0.0 0.2 0.5 0.7 1.1 1.2 1.6 1.9 2.3 2.6 2.8 3.2 3.5 3.9 4.0 4.4 4.6 4.9 5.1

10 inch 0 0.0 0.0 0.1 0.4 0.5 .8 0.9 1.2 1.4 1.7 1.9 2.1 2.3 2.6 2.8 3.0 3.2 3.3 3.6 3.7


133-300A, 133-301A, 133-302A, 133-319A, 133-320A and 133-321ATable of Contents Index Seed Rate 30

Rate Charts, Small Seeds Box, continued...

Millet, Reed Canary

Ladino Clover, Canary Grass,Timothy, Canola

Birdsfoot Trefoil, Sudan


0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100


6 inch 0 0.4 1.4 2.4 3.5 4.4 5.5 6.5 7.5 8.5 9.5 10.5 11.5 12.5 13.6 14.6 15.6 16.6 17.6 18.5 19.0

7.5 inch 0 0.3 1.2 2.0 2.8 3.6 4.4 5.2 6.0 6.8 7.6 8.4 9.3 10.1 10.9 11.7 12.5 13.3 14.1 14.9 15.1

10 inch 0 0.3 0.8 1.4 2.0 2.6 3.2 3.8 4.4 5.0 5.6 6.2 6.8 7.4 8.0 8.6 9.2 9.8 10.4 10.9 11.5


0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100


6 inch 0 0.0 1.1 2.1 3.3 4.7 6.1 7.6 9.2 10.7 12.2 13.8 15.5 17.0 18.5 20.3 21.7 23.4 25.4 27.3 29.2

7.5 inch 0 0.0 0.9 1.6 2.6 3.9 4.9 6.1 7.4 8.6 9.8 11.1 12.5 13.7 14.9 16.3 17.6 18.8 20.4 21.9 23.5

10 inch 0 0.0 0.6 1.5 1.9 2.5 3.6 4.5 5.4 6.3 7.2 8.1 9.1 10.0 10.9 12.0 12.9 13.8 14.9 16.1 17.2


0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100


6 inch 0 0.0 1.7 3.3 5.2 6.8 8.7 10.7 12.7 14.7 16.8 19.2 21.2 23.4 25.6 28.0 29.9 32.1 34.2 36.3 38.4

7.5 inch 0 0.0 1.4 2.6 4.2 5.4 7.0 8.6 10.2 11.9 13.5 15.4 17.0 18.8 20.5 22.5 24.0 25.8 27.6 29.1 30.9

10 inch 0 0.0 1.0 1.9 3.1 4.0 5.1 6.3 7.5 8.6 9.9 11.3 12.5 13.8 15.1 16.5 17.6 18.9 20.2 21.4 22.7



Maintenance

Small Seeds Box Clean-Out1. Open lid of each box and scoop out as much seed as

possible.

2. To recover remaining seed, place a collection tarpunder the small seeds tubes at the openers.

3. Raise drill.

4. Set seed rate handles to 100.

5. Rotate gauge wheels until no seed flows.

6. If a vacuum cleaner is available, remove anyresidual seed from top of meters.

Chain MaintenanceInspect and lubricate chains regularly. The slack of newchains tends to increase during the first few hours ofoperation due to seating.

Chain SlackCheck slack within the first 8 hours of operation andtighten idlers as necessary.

Refer to Figure 41, which, for clarity, greatly exaggerates slack, and omits the idlers.

1. Measure the span for allowable slack:Locate the longest span of each chain (usually thespan which does not run through the idlers). Theideal slack is between 2% and 4% of the span.For example:A slack of 1 cm is appropriate for a 30 cm span.

2. Measure the current slack :Acting at a right angle to the chain span at the centerof the span, deflect the chain in both directions with aforce of about 9 pounds (4 kg). The slack is thedistance of the movement.

3. Adjust the idlers for ideal slack.

Whenever mounting a chain, make sure the clip at theremovable link is oriented to minimize snags.

Refer to Figure 42

Install clip with open end facing away from direction ofchain travel (shown by gray arrows in chain routingdiagrams).

2

1

Figure 41Measuring Chain Slack

27264

1

Figure 42Chain Clip Orientation

26482

2


133-300A, 133-301A, 133-302A, 133-319A, 133-320A and 133-321ATable of Contents Index Maintenance 32

LubricationSmall Seeds Meter Shaft Bearing

1 zerks per shaft, drive end;2 total

Type of Lubrication: GreaseQuantity: Until grease emerges

Small Seeds Drive Chains

4 chains per section; 12 total

Type of Lubrication: Chain LubeQuantity: Coat thoroughly

Slack:1/4 inch (6 mm) main shaft to jackshaft chain1/4 inch (6 mm) Small Seeds drive input chain1/2 inch (13 mm) in top span of long chain1/4 inch (6 mm) in longest span of final drive chain

25

27224

As Required

17180



Appendix

Metric Rate Charts, Small Seeds BoxSee page 25 for instructions.Charts in U.S. customary units begin on page 29.

Alfalfa, Red Alsike, Crimson Clover

Kentucky Bluegrass,Fescue, Annual Rye Grass

Bermuda, Red Top, Lespedeza Unhulled,Sercia, Sand, Weeping Love Grass

Red & Sweet Clover, Lespedeza Hulled

Metric Small Seeds Cup Lever Setting

0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100

Rows Seeding Rate in Kilograms per Hectare

15.2cm (6in) 0 0.0 2.5 3.9 5.4 6.8 8.5 9.8 11.0 12.6 14.1 15.5 17.0 18.5 19.7 21.0 22.8 24.1 25.8 27.0 28.4

19.1cm (7.5in) 0 0.0 2.0 3.2 4.4 5.4 6.8 7.9 8.9 10.1 11.3 12.5 13.6 14.9 15.8 17.2 18.3 19.4 20.6 21.7 22.9

25.4cm (10in) 0 0.0 1.5 2.4 3.2 3.9 5.0 5.7 6.5 7.4 8.3 9.1 10.0 10.9 11.6 12.6 13.4 14.2 15.1 15.1 15.1


0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100


15.2cm (6in) 0 0.0 0.2 1.4 2.1 3.0 3.7 4.6 5.2 5.9 6.5 7.1 7.7 8.2 8.8 9.4 9.9 10.4 10.9 11.3 11.8

19.1cm (7.5in) 0 0.0 0.2 1.0 1.7 2.5 3.0 3.7 4.2 4.7 5.2 5.7 6.2 6.6 7.1 7.5 7.9 8.3 8.3 9.1 9.5

25.4cm (10in) 0 0.0 0.1 0.8 0.8 1.8 2.3 2.3 2.3 3.5 3.5 4.2 4.5 4.8 5.2 5.5 5.5 6.1 6.1 6.6 7.0


0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100


15.2cm (6in) 0 0.0 0.8 1.2 1.9 2.9 3.7 4.6 5.6 6.6 7.4 8.1 8.8 9.5 10.1 10.7 11.5 12.3 13.1 13.7 14.5

19.1cm (7.5in) 0 0.0 0.6 1.0 1.6 2.4 2.9 3.7 4.5 5.3 6.0 6.5 7.1 7.5 8.1 8.6 9.2 9.9 10.5 11.0 11.7

25.4cm (10in) 0 0.0 0.5 0.7 1.1 1.7 2.1 2.7 3.4 3.9 4.4 4.7 5.2 5.2 6.0 6.3 6.8 7.2 7.7 8.1 8.1


0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100


15.2cm (6in) 0 0.0 1.7 3.8 3.8 8.0 10.1 12.7 14.9 17.2 19.2 21.4 23.4 25.4 27.6 29.7 31.9 33.9 36.2 38.1 40.1

19.1cm (7.5in) 0 0.0 1.4 3.0 4.7 6.4 8.1 10.3 11.9 13.9 15.4 17.2 18.8 20.4 22.2 23.9 25.6 27.3 29.1 30.6 32.2

25.4cm (10in) 0 0.0 1.0 2.3 3.5 4.7 6.0 7.5 8.8 10.1 11.3 12.6 13.7 15.0 16.2 17.6 18.7 20.1 21.3 21.3 23.6


133-300A, 133-301A, 133-302A, 133-319A, 133-320A and 133-321ATable of Contents Index Appendix 34

Metric Rate Charts, Small Seeds Box, continued...

Orchard Grass

Millet, Reed Canary

Ladino Clover, Canary Grass,Timothy, Canola

Birdsfoot, Trefoil, Sudan


0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100


15.2cm (6in) 0 0.0 0.0 0.3 0.8 1.0 1.5 1.7 2.3 2.7 3.2 3.7 3.9 4.4 5.0 5.4 5.6 6.2 6.4 6.4 7.1

19.1cm (7.5in) 0 0.0 0.0 0.2 0.6 0.8 0.8 1.4 1.4 1.4 1.4 1.4 3.2 3.6 3.9 4.4 4.5 5.0 5.2 5.5 5.5

25.4cm (10in) 0 0.0 0.0 0.1 0.5 0.6 0.9 1.0 1.4 1.6 1.9 2.1 2.4 2.6 2.9 3.2 3.4 3.6 3.7 4.1 4.2


0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100


15.2cm (6in) 0 0.5 1.6 2.7 3.9 5.0 6.2 7.3 8.5 9.6 10.7 11.8 13.0 14.1 15.3 16.5 17.6 18.7 19.8 20.8 21.4

19.1cm (7.5in) 0 0.3 1.4 1.4 1.4 4.1 5.0 5.9 6.8 7.7 8.6 9.5 10.5 11.4 12.3 13.2 14.1 15.0 15.9 16.8 17.0

25.4cm (10in) 0 0.3 0.9 1.6 2.3 2.3 3.6 4.3 5.0 5.6 6.3 7.0 7.0 8.3 9.0 9.7 10.4 11.0 11.7 12.3 13.0


0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100


15.2cm (6in) 0 0.0 1.2 2.4 3.7 5.3 6.9 8.6 10.4 12.1 13.7 15.5 17.5 19.2 20.7 22.9 24.5 26.4 28.6 30.8 32.9

19.1cm (7.5in) 0 0.0 1.0 1.8 2.9 4.4 4.4 4.4 8.3 9.7 11.0 12.5 14.1 15.4 16.8 18.4 19.8 21.2 23.0 24.7 26.5

25.4cm (10in) 0 0.0 0.7 1.7 2.1 2.8 4.1 5.1 6.1 7.1 8.1 9.1 10.3 11.3 12.3 13.5 14.5 15.5 16.8 18.1 19.4


0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100


15.2cm (6in) 0 0.0 1.9 3.7 5.9 7.7 7.7 12.1 12.1 16.6 18.9 18.9 23.9 26.4 28.8 28.8 33.7 36.2 38.5 40.9 43.3

19.1cm (7.5in) 0 0.0 1.6 1.6 1.6 1.6 7.9 9.7 11.5 11.5 15.2 17.4 17.4 17.4 17.4 25.4 27.0 29.1 31.1 32.8 32.8

25.4cm (10in) 0 0.0 1.1 2.1 3.5 4.5 5.7 7.1 8.5 9.7 11.2 12.7 12.7 15.5 17.0 18.6 19.8 21.3 22.8 24.1 25.6



Torque Values

94 6

25199m

BoltSize

Bolt Head IdentificationBoltSize

Bolt Head Identification

Grade 2 Grade 5 Grade 8 Class 5.8 Class 8.8 Class 10.9in-tpia N-mb N-m N-m mm x pitchc N-m N-m N-m1⁄4-20 7.4 11 16 M 5 X 0.81⁄4-28 8.5 13 18 M 6 X 1 7 11 155⁄16-18 15 24 33 M 8 X 1.25 17 26 365⁄16-24 17 26 37 M 8 X 1 18 28 393⁄8-16 27 42 59 M10 X 1.5 33 52 723⁄8-24 31 47 67 M10 X 0.75 39 61 857⁄16-14 43 67 95 M12 X 1.75 58 91 1257⁄16-20 49 75 105 M12 X 1.5 60 95 1301⁄2-13 66 105 145 M12 X 1 90 105 1451⁄2-20 75 115 165 M14 X 2 92 145 2009⁄16-12 95 150 210 M14 X 1.5 99 155 2159⁄16-18 105 165 235 M16 X 2 145 225 3155⁄8-11 130 205 285 M16 X 1.5 155 240 3355⁄8-18 150 230 325 M18 X 2.5 195 310 4053⁄4-10 235 360 510 M18 X 1.5 220 350 4853⁄4-16 260 405 570 M20 X 2.5 280 440 6107⁄8-9 225 585 820 M20 X 1.5 310 650 900

7⁄8-14 250 640 905 M24 X 3 480 760 1050

1-8 340 875 1230 M24 X 2 525 830 1150

1-12 370 955 1350 M30 X 3.5 960 1510 2100

11⁄8-7 480 1080 1750 M30 X 2 1060 1680 2320

11⁄8-12 540 1210 1960 M36 X 3.5 1730 2650 3660

11⁄4-7 680 1520 2460 M36 X 2 1880 2960 4100

11⁄4-12 750 1680 2730

13⁄8-6 890 1990 3230 a. in-tpi = nominal thread diameter in inches-threads per inch

13⁄8-12 1010 2270 3680 b. N· m = newton-meters

11⁄2-6 1180 2640 4290

11⁄2-12 1330 2970 4820

c. mm x pitch = nominal thread diameter in mm x thread pitch

Torque tolerance + 0%, -15% of torquing values. Unless otherwise specified use torque values listed above.

5.8 8.8 10.9

25199

ft-lbd ft-lb ft-lb ft-lb ft-lb ft-lb5.6 8 12

6 10 14 5 8 11

11 17 25 12 19 27

13 19 27 13 21 29

20 31 44 24 39 53

22 35 49 29 45 62

32 49 70 42 67 93

36 55 78 44 70 97

49 76 105 66 77 105

55 85 120 68 105 150

70 110 155 73 115 160

79 120 170 105 165 230

97 150 210 115 180 245

110 170 240 145 230 300

170 265 375 165 260 355

190 295 420 205 325 450

165 430 605 230 480 665

185 475 670 355 560 780

250 645 910 390 610 845

275 705 995 705 1120 1550

355 795 1290 785 1240 1710

395 890 1440 1270 1950 2700

500 1120 1820 1380 2190 3220

555 1240 2010

655 1470 2380

745 1670 2710

870 1950 3160d. ft-lb = foot pounds

980 2190 3560

3 5 7



Abbreviations

Part ListsExisting Parts Affected

3S Three Section MNT MountASY Assembly MST Metric Spherical Two-holeBRG Bearing PLT PlatedCT Cutting RH Right-HandCTR Center RHSNB Round Head Square Neck BoltDR Drive RL RollerEWNT End Wheel No Till SAE Society of Automotive Engineers (standards)FERT Fertilizer SDS SeedsFLG Flanged SLT SlottedGALV Galvanized SML SmallGP Great Plains SMV Slow Moving VehicleGR5 Grade 5 SPH SphericalHEX Hexagonal (6-sided) SPKT SprocketHFS Hex Flange Screw SPTHD Special ThreadHHCS Hex Head Cap Screw (Bolt) SS Set ScrewID Inside Diameter TB TubeIN Inch THD ThreadJS Jackshaft THD CT Thread Cutting (self-tapping)LG Long USS United States Standard (heavy duty standard)LH Left-Hand W/ withMACH Machine X by

Callout Part Number Description Disposition

11 119-190D HANDLE Removed and reinstalled.12 123-492 HANDLE MOUNT RH CHAIN GUARD

13 123-491 HANDLE MOUNT LH CHAIN GUARD

14 150-138D 12’ EWNT LIGHT BRACKET Removed and reinstalled.15 151-454D .25 X 5.22 X 1.93- BOLT 0.5 SHIM

16 171-059D 3/16 LIGHT PLATE MIN TILL Removed and reinstalled.17 195-559D 3 SEC MIN TILL LIGHT BRACKETS Removed and reinstalled.18 195-273S 40’-3S FERT DR SUBASSY LH Bolts and sprocket removed, and reinstalled.19 248-251D MANUAL PAK MOUNTING PLATE Removed and reinstalled.20 801-081C SCREW HEX SELF TAP 1/4-20X3 Removed and reinstalled.21 802-004C HHCS 1/4-20X3/4 GRD5 Removed and reinstalled.22 802-034C HHCS 1/2-13X1 1/4 GR5 Removed and reinstalled.23 802-203C HFSS 1/2-13X1 1/2 GR5 Removed and reinstalled.24 803-006C NUT HEX 1/4-20 PLT Removed and reinstalled.25 803-020C NUT HEX 1/2-13 PLT Removed and reinstalled.26 803-169C NUT HEX FLG. LOCK 1/2-13 PLT. Removed and reinstalled.27 804-006C WASHER LOCK SPRING 1/4 PLT Removed and reinstalled.28 804-015C WASHER LOCK SPRING 1/2 PLT Removed and reinstalled.29 804-016C WASHER FLAT 1/2 SAE PLT Removed and reinstalled.30 804-075C WASHER FLAT 1/4 USS PLT Removed and reinstalled.31 805-180C PIN ROLL 1/4 X 1 1/2 LG PLT Removed and reinstalled.



New Parts

32 808-143C SPKT 40B12 7/8 HEX BORE W/SS Removed and reinstalled.33 833-697C LIGHT, AMBER LAMP LED Removed and reinstalled.34 833-696C LIGHT, RED LAMP - LED Removed and reinstalled.35 ASSEMBLY RED LAMP Removed and reinstalled.36 ASSEMBLY AMBER LAMP Removed and reinstalled.

Callout Part Number Description Disposition

Kits: 133-300A 3S-4000 7.5" SMALL SEEDS BUNDL133-301A 3S-4000 6" SMALL SEEDS BUNDL133-302A 3S-4000 10" SMALL SEEDS BUNDL133-319A 3S-4000F 7.5" SMALL SEEDS BNDL133-320A 3S-4000F 6" SMALL SEEDS BNDL133-321A 3S-4000F 10" SMALL SEEDS BNDL

CalloutPart

Number

Quantity in Kit 133-

Part Description-300A -301A -302A -319A -320A -321A

101 133-322M 1 1 1 1 1 1 MANUAL 3S4000 SMALL SEEDS

102 123-491D 3 3 3 3 3 3 HANDLE MOUNT LH CHAIN GUARD

103 123-492D 3 3 3 3 3 3 HANDLE MOUNT RH CHAIN GUARD

104 123-939H 63 78 48 0 0 0 SMALL SEEDS TUBE WELDMENT

105 133-070D 1 1 1 1 1 1 3000 SMV MOUNTING BLADE

106 133-128H 0 0 0 63 78 48 SGS SIDE DELIVERY TUBE

107 133-153K 0 3 0 0 3 0 2600 SML SDS RH BOX ASY 6 IN

108 133-155K 3 0 0 3 0 0 2600 SML SDS RH BOX ASY 7.5 IN

109 133-157K 0 0 3 0 0 3 2600 SML SDS RH BOX ASY 10 IN

110 133-158H 3 3 3 3 3 3 SML SDS LH MOUNT WLDM

111 133-163K 3 3 3 3 3 3 2600 SMLSDS RH MOUNT&DRIVE ASY

112 133-324K 3 3 3 3 3 3 SML SDS ON FERT JS MNT ASY

113 136-064D 3 3 3 0 0 0 CHAIN RL #40 51 PITCHES




117 195-269H 3 3 3 0 0 0 40’-3S FERT DRIVE WELDMENT RH

118 195-270D 1 1 1 0 0 0 HEX SHAFT 7/8,4000 FERT JS CTR

119 195-271D 1 1 1 0 0 0 HEX SHAFT 7/8,4000 FERT JS RH

120 195-272D 1 1 1 0 0 0 HEX SHAFT 7/8,4000 FERT JS LH

121 800-321C 126 156 96 126 156 96 HOSE CLAMP NO.12 3/4 ID

122 801-002C 126 156 96 0 0 0 SCREW HEX SLT10-16X1/2P.THD CT

123 802-004C 2 2 2 2 2 2 HHCS 1/4-20X3/4 GR5

124 802-007C 2 2 2 2 2 2 HHCS 5/16-18X3/4 GR5

125 802-034C 20 20 20 13 13 13 HHCS 1/2-13X1 1/4 GR5

126 802-041C 3 3 3 0 0 0 HHCS 1/2-13X3 1/2 GR5

127 802-203C 12 12 12 12 12 12 HFSS 1/2-13X1 1/2 GR5

128 802-282C 12 12 12 0 0 0 RHSNB 5/16-18X1 GR5

129 802-388C 12 12 12 12 12 12 HFS 3/8-16X1 GR5

130 802-427C 0 0 0 63 78 48 HFS 3/8-16X3 3/4 SPTHD

131 803-006C 2 2 2 2 2 2 NUT HEX 1/4-20 PLT



132 803-008C 14 14 14 2 2 2 NUT HEX 5/16-18 PLT

133 803-014C 12 12 12 12 12 12 NUT HEX 3/8-16 PLT

134 803-020C 24 24 24 13 13 13 NUT HEX 1/2-13 PLT

135 803-036C 6 6 6 0 0 0 NUT HEX JAM 1/2-13 PLT

136 803-169C 12 12 12 12 12 12 NUT HEX FLG. LOCK 1/2-13 PLT.

137 803-209C 0 0 0 63 78 48 NUT FLANGE LOCK 3/8-16 PLT

138 804-006C 2 2 2 2 2 2 WASHER LOCK SPRING 1/4 PLT




142 804-061C 6 6 6 0 0 0 WASHER MACH 1.50 X 1.00 X 18GA

143 804-113C 16 16 16 6 6 6 WASHER FLAT 1/2 USS HARD PLT

144 805-180C 6 6 6 0 0 0 PIN ROLL 1/4 X 1 1/2 LG PLT

145 806-060C 2 2 2 0 0 0 U-BOLT 1/2-13 X 6 1/32 X 7 1/4

146 808-194C 3 3 3 3 3 3 SPKT 40B22 7/8 HEX BORE & SS

147 808-256C 3 3 3 0 0 0 SPKT 40C23 X 7/8 HEX BORE

148 816-358C 63 78 48 63 78 48 SGS HOSE 122 RIBS

149 817-025C 3 3 3 0 0 0 NO. 40 12T IDLER SPKT.

150 817-806C 63 78 48 63 78 48 SMALL SEEDS CUP WIND SHIELD

151 818-055C 1 1 1 1 1 1 DECAL SLOW MOVING-GALV. BACKED

152 822-032C 12 12 12 0 0 0 FLANGETTE 52 MST

153 822-119C 6 6 6 0 0 0 BRG 7/8HEXX2.05OD SPH

154a 838-160C 40 40 40 40 40 40 DECAL 3 COLOR STRIPE 2.50 WIDE

155a 838-161C 1 1 1 1 1 1 DECAL LOGO&GP F/STRIPE 4 X 24

156a 838-206C 1 1 1 1 1 1 DECAL 3S-4000

157a 838-467C 1 1 1 1 1 1 DECAL SMALL SEEDS DANGER

a. These parts are pre-installed and are not called out in the instructions.

CalloutPart

Number

Quantity in Kit 133-

Part Description-300A -301A -302A -319A -320A -321A


133-300A, 133-301A, 133-302A, 133-319A, 133-320A and 133-321ACover Table of Contents 39

Index

Aabbreviation ........................................35acremeter ...........................................25alfalfa ..................................................28annual rye grass .................................28

Bbermuda .............................................28birdsfoot trefoil ....................................29

Ccalibration ...........................................25canary grass .......................................29canola .................................................29CAUTION, defined ...............................1chain clip ............................................30chain maintenance .............................30clean-out .............................................30closeout ..............................................23clothing .................................................1clutch bearing plate ..............................3compatibility ..........................................3crimson clover ....................................28customer service ..................................4

DDANGER, defined ................................1Document Family .................................3drill bit ...................................................5

Eexisting parts ......................................35

Ffescue .................................................28fire ........................................................1

Ggusset plate ..........................................3

Hheadphones ..........................................1hearing .................................................1high pressure fluids ..............................2hydraulic safety ....................................2

Kkentucky bluegrass .............................28

Lladino clover .......................................29left-hand (defined) ................................4lespedeza unhulled ............................28lever ....................................................24loading seed .......................................24

Mmaintenance .......................................30maintenance safety ..............................2medical assistance ...............................2millet ...................................................29

Nnew parts ........................................... 36Note (defined) ...................................... 4Notice (defined) .................................... 4

Oorchard grass ..................................... 28

Ppart lists .............................................. 35plugs, small seeds ............................. 27plug, meter ......................................... 27plug, small seed ................................. 27protective equipment ............................ 1

Rred alsike............................................ 28red clover ........................................... 28red top ................................................ 28reed canary ........................................ 29right-hand (defined) .............................. 4rotations, calibration ........................... 25row shut-off ........................................ 27

Ssafety symbol ....................................... 1sand ................................................... 28seed rate ............................................ 24seed rate charts (metric) .................... 32seed rate charts (USc) ....................... 28sercia ................................................. 28service.................................................. 4Shut-Off

Small Seeds................................ 27shut-off ............................................... 27slack ................................................... 30slack, chain ........................................ 30SMV ................................................... 23sudan ................................................. 29support ................................................. 4sweet clover ....................................... 28symbol, safety ...................................... 1

Ttimothy ............................................... 29tires .................................................... 25tools ..................................................... 5torque values ..................................... 34

WWARNING, defined .............................. 1weeping love grass ............................ 28welding ................................................. 2wing nut .............................................. 24

Numerics119-190D, handle ...................6,10,11123-491D, guard ................................ 10123-491D, mount ............................... 12

123-492D, guard.................................11123-492D, mount ................................12123-939H, tube ...................................21133-070D, blade .................................23133-128H, tube ...................................22133-153K, box ....................................10133-155K, box ....................................10133-157K, box ....................................10133-158H, weldment ............................8133-163K, drive ....................................9133-300A, kit ........................................3133-301A, kit ........................................3133-302A, kit ........................................3133-315H, plug ...................................27133-319A, kit ........................................3133-320A, kit ........................................3133-321A, kit ........................................3133-322M, manual................................3133-324K, drive .................... 15,16,19136-064D, chain .................................17136-078D, chain .................................20136-104D, chain .................................12136-154D, chain .................................21150-138D, bracket ................................6195-067B, manual ................................3195-067M, manual................................3195-067P, manual ................................3195-095A, ladder kit .............................5195-242B, manual ................................3195-242M-A, manual ............................3195-242P, manual ................................3195-269H, weldment ................... 15,16195-270D, shaft ..................................14195-271D, shaft ..................................14195-272D, shaft ..................................14195-273S, drive ..................................18195-325B, manual ................................3195-394M, manual................................3195-417D (RH), bracket .....................12248-251D, plate ............................. 6,10265/70B16.5 NHS...............................253S-4000F-6375.....................................33S-4000F-7806.....................................33S4000HDF-4810.................................33S4000HDF-6375.................................33S4000HDF-7806.................................33S-4000HD-4810..................................33S-4000HD-6375..................................33S-4000HD-7806..................................33S-4000-4810 .......................................3800-321C, clamp ................................22801-002C, screw ................................21802-004C, bolt ....................................23802-007C, bolt ....................................23

2017-08-08 Cover Table of Contents 133-322M

133-300A, 133-301A, 133-302A, 133-319A, 133-320A and 133-321ACover Table of Contents 40

802-034C, bolt .............8,9,15,16,19802-041C, bolt ....................................13802-203C, bolt .......... 6,7,8,9,10,11802-282C, bolt ...................... 13,15,16802-388C, bolt ....................................10802-427C, bolt ....................................22803-006C, nut .....................................23803-008C, nut .................13,15,16,23803-014C, nut .....................................10803-020C, nut ..............8,9,15,16,19803-036C, nut .....................................13

803-169C, nut ...........6,7,8,9,10,11803-209C, nut .................................... 22804-006C, washer .............................. 23804-009C, washer .......... 13,15,16,23804-013C, washer .............................. 10804-015C, washer .8,9,13,15,16,19804-016C, washer ............................6,7804-061C, washer .............................. 14804-113C, washer .......... 13,15,16,19805-180C, pin ................ 14,17,18,20806-060C, U-bolt ................................ 16

808-143C, sprocket ..................... 18,19808-194C, sprocket .............. 14,18,20808-256C, sprocket ............................14816-358C, hose ..................................22817-025C, idler ...................................13817-806C, wind shield ........................23818-055C, decal .................................23822-032C, flangette .............. 13,15,16822-119C, bearing ................ 13,15,16

2017-08-08 Cover Table of Contents 133-322M

Great Plains, Mfg.1525 E. North St.P.O. Box 5060Salina, KS 67402

installation, operation and maintenanceassets.greatplainsmfg.com/manuals/pdf/133-322m.pdf · tablet...

Documents