I N ST R U CT I O N M A N UA L

TABLE OF CONTENTS

3

Care Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Bed Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6

Metal Frame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Set Foundation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Position Heater Pad . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9

Place and Align Bottom of Stretch Cover . . . . . . . . . . . . 11

Install Foam Rails . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Install Vinyl Liner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Place Water Mattress . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Filling Your Waterbed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Burping Your Waterbed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Laying Memory Foam . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Zipping Up Your Waterbed . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Draining Your Waterbed . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Moving Your Waterbed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Limited Manufacturer’s Waterbed Warranty . . . . . . . .25

Limited Manufacturer’s Space Saver Warranty . . . . . 28

TABLE OF CONTENTS

4

CARE KIT:

5

Lay out all items in your waterbed and Care Kit . Ensure you have all of the following:

Waterbed Conditioner (2)

Air Extractor25 ft . Hose Carrying Sling

Alignment Pins Bolts and Allen Wrenches

Fill & Drain Kit: 1 . Valve Adaptor 2 . Shutoff Valve 3 . Faucet Adaptor 4 . Venturi Pump 5 . Fill Meter

Patch Kit

6

BED COMPONENTS:

King Foundation2 Boxes

Queen Foundation1 Box

Stretch Cover (Top)

(4) Foam Rails

Vinyl Liner

Stretch Cover (Bottom)

Water Mattress

DUAL KING QUEEN/STANDARDKING

FIRM FLOATATION

120W Heater (2)

Thermal Divider

300W Heater

Memory Foam Insert

7

METAL FRAME (Sold Separately):

Build your 9-legged metal frame according to the instructions provided with the frame .

Place bed frame approximately 3” from wall to attach headboard and footboard (sold separately) .

After the metal bed frame is assembled, if a headboard is going to be connected to the Afloat metal bed frame it should be done before proceeding .

NOTE: Make sure your bed positioning is final before continuing the set up process . The bed will not move once water is added to the mattress .

Traditional Bed Frame Space Saver Bed Frame

8

SET FOUNDATION:

Place the foundation(s) paying close attention to header and footer labels .

QUEEN

KING

9

NOTE: For Standard King, you will only have one 300W heater pad and control . Select one side, the heat will disperse throughout the bed .

DUAL KING

QUEEN

POSITION HEATER PAD:

Position heater pad in the designated rectangles .

STANDARD KING

10

Run the power cord down through deck hole and connect to the temperature control . Decide which side of the bed you would like the temperature control unit . TIP: Select the side closest to an outlet.

Run the temperature sensor up through the deck hole and position on deck at least 10” from heater pad .

Affix the temperature control unit to the side of the foundation .

DO NOT PLUG IT IN TO WALL.

11

PLACE AND ALIGN BOTTOM OF STRETCH COVER:

Place the alignment rods and tighten about ¼” (about 3 turns) . Do not tighten all the way .

Place stretch cover bottom panel by sliding the grommets over the alignment bolts .

12

INSTALL FOAM RAILS:

Place foam rails, paying close attention to the labels on the header, footer, and side rails . Place over alignment bolts .

Remove the alignment pins and replace with the provided wider-headed bolts . Tighten the bolts all the way .

Return the pins back into the ziploc bag in your Care Kit . You will need them if you move or reassemble your Afloat .

13

INSTALL VINYL LINER:

Stretch the vinyl liner over the foam rails paying special attention to the orientation of the liner with the label “Foot End” at the bottom .

Ensure there are no wrinkles in the liner above or near the heater and that the heater pad has not shifted and is still lying flat . A heater folded on itself or wrinkles in the liner above the heater may cause heater failure .

14

PLACE WATER MATTRESS:

Place the water mattress equidistant from all sides with the valve at the foot of the bed .

Make sure the corners of the mattress are aligned with the corners of the liner .

If the vacuum in the mattress is preventing this, add a slight amount of air through the valve to allow you to align the corners .

DUAL KING: Place both mattresses side-by-side with both valves at the foot of the bed, and aligned at the center .

Place the thermal divider after placing the mattresses . The vinyl flaps of the divider must be below the water mattresses .

15

FILLING YOUR WATERBED:

BEFORE YOU ADD ANY WATER, AGAIN CHECK TO MAKE SURE THE BED IS POSITIONED EXACTLY WHERE YOU WANT IT. Once you start filling the water mattress you will not be able to change the position .

Attach female end of hose to an outdoor spigot or a bathroom faucet, using the faucet adaptor .

Thread the valve adaptor, fill meter, and the shutoff valve to the other end of the hose accordingly .

The fill meter will help insure that your mattress get the proper amount of water .

NOTE: Do not use cold water . Using lukewarm water instead will drastically reduce the time needed for your bed to reach your desired temperature . Do not use hot water either, as this could damage your fill meter and/or your mattress .

16

Unscrew the valve cover and remove the safety cap, and quickly thread the valve adaptor to the mattress valve . Do this as quickly as possible to prevent air from getting in the mattress .

Turn on your water source then open the shutoff valve to start filling your waterbed . 

17

QUEEN AND STANDARD KING

When your water mattress is approximately halfway filled, close the shutoff valve, unthread the adaptor from the mattress valve, and pour the entire bottle of water conditioner into the mattress valve .

NOTE: be sure to follow the fill guide provided in the care kit .

Once conditioner is added, continue filling the mattress . 

NOTE: A good fill on your waterbed is approximately 1⁄2” to 3⁄4” below the top of the foam rails . There will be wrinkles at the top of your mattress . This allows the mattress to conform to the shape of your body .

DO NOT OVERFILL. It is easier to add water than to remove it . When the mattress is full, it is safe to plug your temperature control into a wall receptacle .

DUAL KING 1 . 35 gallons to left side . 2 . 35 gallons to right side . 3 . Align thermal divider between mattresses . 4 . 35 more gallons to the left side 5 . 35 more gallons to the right side .

STANDARD KING 140 gallons

STANDARD QUEEN 110 gallons

18

DUAL KING

Fill one of the mattresses halfway then close the shutoff valve, unthread the adaptor from the mattress valve, and add half of the water conditioner .

NOTE: Be sure to follow the fill guide provided on the previous page .

Quickly seal the mattress valve and start filling the other mattress to approximately halfway then add the rest of the water conditioner

Continue filling the waterbed . Switch filling between the two mattresses to ensure an even fill . 

A good fill on your waterbed is approximately 1⁄2” to 3⁄4” below the top of the foam rails . There will be wrinkles at the top of your mattress . This allows the mattress to conform to the shape of your body .

DO NOT OVERFILL. It is easier to add water than to remove it . When both mattresses are full, it is safe to plug your temperature controls into a wall outlet .

19

Thread the air extractor to the valve . Slowly pull the other end of the air extractor . Continue until all the air is removed from the mattress . If you pull water, stop .

“BURPING” YOUR WATERBED:

Pull up on the valve and lay on the other side of the mattress . This pushes any air out of the mattress . If any air bubbles remain, use your forearms to slowly push them towards the valve .

20

LAYING MEMORY FOAM (Firm Flotation):

If you have our Firm Flotation model, place the memory foam layer over your mattress . Slide the elastic skirt between the bottom of the stretch cover and the vinyl liner .

Lift up the bottom skirt of the cover around the memory foam insert in order to put the top cover on .

21

ZIPPING UP YOUR WATERBED:

Place the cover over the waterbed with the label towards the foot of the bed . Thread the zipper at the foot of the bed .

Zip up the stretch cover . TIP: Run your finger along the zipper path to ease the zipping .

Reassemble your Care Kit and place it under your bed . You will use the Air Extractor to help you remove accumulated air in the water .  Air accumulation becomes infrequent over time .

22

DRAINING YOUR WATERBED:

Attach the Venturi pump to the spigot or the faucet .

Attach the hose to the side of the Venturi pump .

Thread the valve adaptor with the shutoff valve to the other end of the hose .

23

Insert valve adaptor into mattress valve .

Alternative Method: You may use an electric siphon pump instead of the plastic, water-driven pump provided in your Care Kit . If you use this method, follow the pump manufacturer’s instructions .

In general, the shorter and more rigid the hose from the pump to mattress, the less likely the hose will collapse from too much suction .

Open shutoff valve and start running water INTO THE MATTRESS to purge the hose of air . Turn the Venturi pump to “drain,” while leaving the water running . This creates a siphon and drains your waterbed .

Continue running water until your waterbed is completely drained . 

TIP: Place a weighted object on the valve to ensure adaptor is below water .

24

MOVING YOUR WATERBED:

After you have drained your waterbed, roll up the mattress .

Place the mattress in the carrying sling .

Finally, reverse the steps from the instruction manual to break down the rest of the bed .

In the carrying sling, 2-4 people can carry the mattress, as it will be heavy .

25

LIMITED MANUFACTURER’S WATERBED WARRANTY

WHAT IS THIS?

Your new AFLOAT waterbed (the “product” or “waterbed”) purchased from Hall Flotation LLC (“Hall Flotation”) — maker of AFLOAT, The New Waterbed — is protected by a 20-year limited manufacturer’s warranty (“limited warranty” or “warranty”) . This limited warranty covers manufacturing defects in your waterbed, including faults in materials or manufacturing defects . This warranty explains your specific legal rights, and you may also have other rights which may vary from state to state . This limited warranty is valid only to the original purchaser (may also be referred to as “you” or “customer”), either from a Hall Flotation retail partner (a “Partner”) or directly from Hall Flotation, and is not transferable .  You must provide a copy of your receipt to prove that you purchased the mattress .

WHAT DO YOU NEED TO KEEP?

Attached to every waterbed is a law tag that includes a warranty code number . If you remove this tag, keep it with your receipt, as both will be required for warranty coverage . An example is shown on the right:

No expressed or implied warranties are extended to people who purchase the product from anyone other than Hall Flotation or its partners, and all warranties to you, including any implied warranties of merchantability and fitness, are hereby excluded .

Carefully inspect your waterbed and all of the components, hardware, and parts upon receipt and inform Hall Flotation or the partner immediately if you have any concerns .

HOW LONG DOES THIS WARRANTY LAST?

The term of this warranty begins upon the purchase of your AFLOAT . Replacement of any or all components of the waterbed does not extend this limited warranty or begin a new limited warranty period . This warranty will no longer be valid after 20 years from the purchase date of your AFLOAT for all components, except the box foundation, which will be valid for 1 year from the purchase date . The duration of any applicable implied warranties, including, but not limited to the implied warranties of merchandise and

UNDER PENALTY OF LAW THIS TAG NOT TO BE REMOVED

BY THE CONSUMER

ALL NEW MATERIAL CONSISTING OF

REG. NO OR LIC NO.

YOUR MANUFACTURER

(ADDITIONAL INFORMATION) Warranty Code Found Here

26

fitness, shall not exceed the term of this limited warranty . Some states do not allow limitations of how long an implied warranty lasts, so this limitation may not apply to you .

WHAT HAPPENS IF YOU MAKE A CLAIM UNDER THIS WARRANTY?

To receive service under the terms of this warranty contact Hall Flotation at 1 (844) 4-AFLOAT or info@afloatsleep .com or the partner you purchased your waterbed from . A copy of original bill of sales is needed to determine original date of purchase and the law tag is needed to provide you with the proper parts .

If your waterbed fails due to manufacturing defect, the exclusive remedy under this warranty will be repair or replacement (as applicable) of the defective waterbed or the component . The decision to replace or replace a waterbed or the individual defective component shall be at the sole and absolute discretion of Hall Flotation or the partner . If the waterbed you purchase is discontinued at the time of replacement and the components are not available to replace the defective component, a current model of comparable quality and value will be selected to replace your waterbed, to be selected at Hall Flotation’s or the partner’s discretion, or you may opt to upgrade to a more expensive waterbed . If you opt to upgrade your waterbed at this time, you may be required to pay the price difference between the original waterbed and the more expensive waterbed . If you receive a repaired or replaced waterbed or components, you are subject to the same term as the original warranty .

HOW MUCH DOES THIS COST YOU?

The following chart details the term and replacement period for this warranty .

During the first 3 years of your warranty term, Hall Flotation will cover all shipping costs associated with claims under this warranty within the 48 contiguous United States . After the initial 3 year term, shipping costs will be covered by you .

Replacement Term

Years 1 through 3

Years 4 through 8

Years 9 through 14

Years 15 through 20

% Cost Covered by Hall Flotation

100%

60%

40%

20%

Replacement Cost for Customer

Full cost of the component covered

40% of the MSRP of the component at the time of the claim

60% of the MSRP of the component at the time of the claim

80% of the MSRP of the component at the time of the claim

27

WHAT IS NOT INCLUDED IN THIS WARRANTY?

Your Warranty excludes the following:

1 . Customer firmness/comfort preference

2 . Customer bed height/weight preference

3 . Burns, cuts, tears, punctures, physical abuse of the product, neglect, leaks caused by customer, improper cleaning, improper filling or install of components not done by a partner, or normal wear and tear

4 . Vermin infestation

5 . Algae, mold, or other contaminates inside or outside the vinyl water mattress

6 . Shifting of the support system inside the vinyl water chamber due to installing or moving the bed, not in accordance with the AFLOAT Installation and Draining Instructions

7 . Any other damages resulting from misuse or non-compliance with the AFLOAT Installation and Draining Instructions

8 . Waterbed, stretch covers, or any other fabric displaying stains or soil that reasonably indicates the presence of potentially dangerous bodily fluids, or other substances that could cause injury

9 . Placing your AFLOAT waterbed on any frame other than a 9-legged frame that supports at least 2000 pounds (or the Space Saver Foundation)

10 . Merchandise sold “as-is,” “distressed,” “clearance”, “outlet”, or “floor model/sample”

11 . Claims made outside of the 48 contiguous United States and the District of Columbia

12 . Transportation, inspection, or removal costs of product, except in California

13 . Any non-conforming use of AFLOAT or any of its parts and components

14 . Improper storage of the waterbed

15 . Unauthorized commercial use

16 . Purchase from resellers that are not Partners of Hall Flotation

17 . Individual or personalized allergies and sensitivities

18 . Naturally occurring aromas from cotton, vinyl, or other components

19 . Minor imperfections or cosmetic flaws

20 . Any costs related to draining or filling your waterbed, including utilities and water costs

21 . The Care Kit and any items contained within the Care Kit

22 . Any Customer personal preferences . Replacement of one piece of your waterbed due to a manufacturing defect does not automatically result in the replacement of any other piece or the whole waterbed .

28

LIMITED MANUFACTURER’S SPACE SAVER WARRANTY

WHAT IS THIS?

Your new Space Saver foundation (“Space Saver” or “foundation”) from Hall Flotation LLC (“Hall Flotation”) — maker of AFLOAT, The New Waterbed — is protected by a 1 year limited manufacturer’s warranty (“limited warranty” or “warranty”) . This limited warranty covers manufacturing defects in your waterbed, including faults in materials or manufacturing defects . This warranty explains your specific legal rights, and you may also have other rights which may vary from state to state . This limited warranty is valid only to the original purchaser (may also be referred to as “you” or “Customer”), either from a Hall Flotation retail partner (a “partner”) or directly from Hall Flotation and is not transferable . You must provide a copy of your receipt to prove that you purchased the foundation .

HOW LONG DOES THIS WARRANTY LAST?

The term of this warranty begins upon the purchase of your Space Saver . Replacement of any or all components of the Space Saver does not extend this limited warranty or begin a new limited warranty period . This warranty will no longer be valid after 1 year from the purchase date of your Space Saver for all components . The duration of any applicable implied warranties, including, but not limited to the implied warranties of merchandise and fitness, shall not exceed the term of this limited warranty . Some states do not allow limitations of how long an implied warranty lasts, so this limitation may not apply to you .

WHAT HAPPENS IF YOU MAKE A CLAIM UNDER THIS WARRANTY?

To receive service under the terms of this warranty contact Hall Flotation at 1 (844) 4-AFLOAT or info@afloatsleep .com or the partner you purchased your waterbed from . A copy of original bill of sales is needed to determine original date of purchase .

If your foundation fails due to manufacturing defect, the exclusive remedy under this warranty will be repair or replacement (as applicable) of the defective foundation or the component in the U .S ., Puerto Rico, or U .S . Virgin Islands . The decision to replace a foundation or the individual defective component shall be at the sole and absolute discretion of Hall Flotation or the partner . If the foundation you purchase is discontinued at the time of replacement and the components are not available to replace the

29

defective component, a current model of comparable quality and value will be selected to replace your foundation, to be selected at Hall Flotation’s or the partner’s discretion, or you may opt to upgrade to a more expensive foundation . If you opt to upgrade your foundation at this time, you may be required to pay the price difference between the original foundation and the more expensive foundation . If you receive a repaired or replaced foundation or components, you are subject to the same term as the original warranty .

HOW MUCH DOES THIS COST YOU?

During the 1 year term, you will not be responsible for any costs related to shipping or otherwise for any claim made under this Warranty .

WHAT IS NOT INCLUDED IN THIS WARRANTY?

Your Warranty excludes the following:

1 . Customer bed height/weight preference

2 . Burns, cuts, tears, punctures, physical abuse of the product, neglect, leaks caused by customer, improper cleaning, improper filling or install of components not done by a partner, or normal wear and tear

3 . Any damaged caused by improper installation or maintenance not in accordance with Space Saver Installation Instructions

4 . Merchandise sold “as-is,” “distressed,” “clearance”, “outlet”, or “floor model/sample”

5 . Claims made outside of the 48 contiguous United States and the District of Columbia

6 . Transportation, inspection, or removal costs of product, except in California

7 . Any non-conforming use of AFLOAT or any of its parts and components

8 . Improper storage of the foundation

9 . Unauthorized commercial use

10 . Purchase from resellers that are not partners of Hall Flotation

11 . Minor imperfections or cosmetic flaws

12 . Exceeding the weight limit of the foundation

13 . Replacement of non-defective piece

14 . Structural or visual damage from using an improper bed frame or placing foundation on the floor

30

15 . Placement and fit of foundation within bed sets or bedroom packages

16 . Customer personal preferences . Replacement of one piece of your foundation due to a manufacturing defect does not automatically result in the replacement of any other piece or the whole foundation .

31

The following applies to all warranties and guarantees offered by Hall Flotation.

LIMITATION OF LIABILITY

The warranties offered from Hall Flotation give you specific rights, and you may have other rights, which may vary from state to state . The warranties extend only to the original purchaser from Hall Flotation or its partners .

To the extent permissible by applicable law, all waterbeds and Foundation are provided “as is” and this warranty and the 100 Night Comfort Guarantee are applicable only to new waterbeds, and any implied warranties are exclusive warranties and replace all other warranties or conditions, express or implied . In states or other jurisdictions that do not allow the exclusion of implied warranties, the exclusions mentioned herein may not apply to you . Other states and jurisdictions may provide other rights that may be applicable .

Any remedies for aforementioned warranties are at Hall Flotation’s sole discretion, which may only include the replacement services described herein . To the maximum extent permitted by any applicable laws and except as set forth in the warranties listed above, in no event will Hall Flotation, partners, or its suppliers be liable for procurement of substitute products or any other special, incidental, consequential, or indirect damages arising out of or related to AFLOAT, Space Saver, or its use by you or any third party, whether under theory of contract, tort (including negligence), indemnity, product liability or otherwise . All limitations included in this warranty, including any damages, even if Hall Flotation has been advised of the damages, and notwithstanding the failure of essential purpose of any limited remedy, shall apply . Hall Flotation’s liability will not exceed the purchase price for the products or components giving rise to such liability . In states or other jurisdictions that do not allow exclusions or limitation of incidental, consequential, or indirect damages, the limitations mentioned herein may not apply to you . These warranties provide you, as the original purchaser, certain legal rights, and you may be entitled to other rights that vary in each jurisdiction .

GOVERNING LAW

These warranties will be governed by the laws of the State of Florida with proper venue lying situated with the appropriate court in Broward County, Florida .

Hall Flotation, LLC1 (844) 4-AFLOAT

6701 North Hiatus Road • Tamarac, FL 33321info@afloatsleep .com