insulation piercing connectors low voltage insulated ... · pdf fileinsulation piercing...

INSULATION PIERCING CONNECTORS LOW VOLTAGE INSULATED SERVICE FITTINGS

LOW VOLTAGE WATERPROOF CONNECTION SYSTEMS

SERVICE FUSE HOLDERS LVABC HARDWARE

SHEAR BOLT CONNECTORS

PERSONAL SAFETY EQUIPMENT INSULATING GLOVES 1000V INSULATED TOOLS INSULATING MATS EARTHING SYSTEMS DETECTORS AND INSTRUMENTS ELECTRICAL SAFETY EQUIPMENT

AUSTRALIA

PRODUCT CATALOGUEPRODUCT CATALOGUEPRODUCT CATALOGUE

WELCOME TO SICAME AUSTRALIA PTY LTD

THE NEW GENERATION OF OVERHEAD AND UNDERGROUND SEALED INSULATION PIERCING CONNECTORS AND FITTINGS

Sicame Australia Pty Ltd has established a strong reputation as the leading manufacturer and supplier of Low Voltage Aerial Bundled Cable (LVABC) Insulation Piercing Connectors and associated equipment in Australia. In response to the growing trend toward the adoption of Overhead Aluminium XLPE Service Cable by numerous supply authorities, Sicame Australia has developed a complete range of products specifically designed for the purpose. This system allows a safe, economic and speedy installation of a customer to overhead mains with pro-vision for cable connection, support and fusing at both the house end and pole end. These products have been tested to the relevant Australian Standards for connectors and hardware as well as European and American Standards. IPC products have been tested in compliance with AS4396 (Int.) 1996 for IPC’s. This catalogue will guide you through the range of overhead and underground connectors and other products that are currently approved and utilised by your local electricity utility. We commend these products to you and your customers.

Robert Battle Managing Director

The team at Sicame Australia headquarters in Queensland

© Sicame Australia Pty Ltd. The information presented here is subject to change without notice. QLD Sales Office: Ph 07 38077022, Fax 07 38077522 NSW Sales Offices: Sydney Ph 02 96213155, Fax 02 96227120

PRODUCT CATALOGUE w 0705


CATALOGUE INDEX I

0107 SECTION A - LVABC CONNECTORS & FITTINGS A1 TTD series IPCs A2 NTD series IPCs A3 In Line Piercing Connectors and Industrial Mains Box A4 Multi-tap IPCs & Earthing A5 LVABC Fuse Switch Disconnectors A6 LVABC Fuse Switch Accessories SECTION B - SERVICE FITTINGS B1 House Service Connectors B2 CAW & CCW series service connectors B3 Mains Connection Boxes B4 Service Fuse Holders SECTION C - PRE-INSULATED FITTINGS C1 MJPB & MJPT series links C2 Pre-crimped links and tools C3 MEPCN series C4 CPTA & CPTAU series lugs SECTION D - UNDERGROUND CONNECTORS D1 MUCI Series submersible D2 Resin Filled Service Tee Joint D3 Bi-form & Tri-form connectors D4 BST & LVM Mechanical Branch Connectors D5 MF Series Mechanical In-Line Connectors D6 UM Series Mechanical In-Line Connectors D7 MF15 HV Mechanical Connectors D8 MF17 HV Mechanical Connectors D9 ML Series Mechanical Connectors (Lugs) D10 WB1, 2 & 3 Series - Mains to Mains Branch Connectors D11 WB4 Mains to Mains Branch Connector D12 WS2 - Mains to Service Branch Connector D13 WS3 - Mains to Service Branch Connector D14 WS4 - Mains to Service Branch Connector D15 WS5 - Mains to Service Branch Connector D16 Protective Covers SECTION E - TOOLS & ACCESSORIES E1 Spanners, testers and wedges E2 Cutters and Strippers E3 Stringing tools E4 Stringing tools E5 Jointing Tools E6 Battery Operated Driver

SECTION F - STRAIN & TERMINATION FITTINGS F1 Service termination clamps F2 Mains termination & suspension clamps SECTION G - HARDWARE G1 Eye bolts, J & Q hooks, brackets G2 Eye nuts, weak links SECTION H - TIME AND LIGHT CONTROLS H1 P.E. Cell - Enclosed light arrestors SECTION J - CATU SAFETY EQUIPMENT J1-J4 Personal Safety J5-J17 1000V Insulated Tools SECTION K - EARTH Systems Accessories K1-K6 Earth Set Accessories K7 Earth Clamps K8 Earth and Stick Bags K9 Lanyards


TTD151XFA

For Connecting INSULATED MAINS to INSULATED MAINS or INSULATED SERVICES The Sicame TTD range of insulation piercing connectors (IPCs) provide a fast, convenient and reliable method of con-necting overhead low voltage mains to services or other mains. All common types of conductors can be intercon-nected, including insulated aluminium or copper. The connectors have been tested to AS4396 and are approved for use by Australian power distribution utilities (Consult for further details).

Product Number

Mains Cable (mm2)

Branch Cable (mm2)

Number of Bolts

Bolt Size

Pack Size

TTD051XFA 16 to 95 1.5 to 10 1 M8 12

TTD101XFA 6 to 54 6 to 35 1 M8 12

TTD151XFA 25 to 95 6 to 35 1 M8 12

TTD201XFA 35 to 95 25 to 95 1 M8 12

TTD241XFA 50 to 150 6 to 35 1 M8 12

TTD251XFA 50 to 150 35 to 95 1 M8 8

TTD301XFA 25 to 95 25 to 95 2 M8 10

TTD341F * 50 to 150 6 to 35 2 M8 10

TTD351XFA 50 to 150 35 to 95 2 M8 4

TTD401XFA 50 to 185 50 to 150 2 M8 4

TTD431XFA 70 to 240 16 to 95 2 M10 4

TTD451XFA 95 to 240 95 to 240 2 M10 4

*Galvanised fasteners

TTD551FJA* 120-380 95-240 2 M10 4

Recommended tool for all products: RPS13/17-6H or RPS13/17-6SH

TTD SERIES INSULATION PIERCING CONNECTOR: Application: Mains cable: Insulated copper or aluminium Tap cable: Insulated copper or aluminium Features: * Provides a fully sealed, waterproof connection * No need to strip cable to make the connection * Simultaneous piercing on main & tap * Torque controlling shear heads on all bolts * Tightening bolts do not come into contact with live

components * Captive end cap for protection of tap cable, which

can be mounted on either side. * Fully bimetallic * Stainless steel fasteners Testing Specification: Tested to AS4396 Installation Notes: When using 2 bolt connectors from this range, each bolt must be tightened a 1/4 to 1/2 turn alternately, until the shear head operates. For tightening the shear head bolts, use only a 13mm AF, six sided hexagon socket (17mm AF for models TTD431XFA, TTD451XFA & TTD551FJA models). For double insulated cables, the outer sheath should be removed before applying the connector.

LVABC CONNECTORS TTD Series

A1 0107

TTD301XFA


Product Number

Bare Conductor Insulated Cable

(mm2) No. of Bolts

Bolt Size

Pack Size Type Size

(mm2) Diameter

(mm) Connectors for Bare Copper Mains

NTD101F * Cu 7 to 54 3.0 to 10.0 6 to 35 1 M8 12

NTD301XFA Cu 7 to 95 3.0 to 12.5 35 to 95 2 M8 10



NTD101AF * Alu 6 to 54 3.0 to 9.5 6 to 35 1 M8 12

NTD301AXFA Alu 7 to 95 3.0 to 12.5 35 to 95 2 M8 10





*Galvanised fasteners

Connectors for Bare Aluminium Mains

NTD SERIES INSULATION PIERCING CONNECTOR: Application: Mains: Bare copper or aluminium Tap: Insulated copper or aluminium Features: * Provides a fully sealed, waterproof connec-

tion on the tap. * No need to strip cable to make the connec-

tion * Simultaneous piercing on main & tap * Torque controlling shear heads on all bolts * Tightening bolts do not come into contact

with live components * Captive end cap for protection of tap cable,

which can be mounted on either side. * Fully bimetallic * Stainless steel fasteners Installation Notes: When using 2 bolt connectors from this range, each bolt must be tightened a 1/4 to 1/2 turn alternately, until the shear head op-erates. For tightening the shear head bolts, use only a 13mm AF, six sided hexagon socket (17mm AF for models NTD431XFA and NTD451XFA). For double insulated cables, the outer sheath should be removed before apply-ing the connector.

NTD351AXFA


For connecting BARE MAINS to INSULATED MAINS or INSULATED SERVICES The Sicame NTD range of insulation piercing connectors provide a fast, convenient and reliable method of connecting overhead low voltage mains to services and other mains. All common types of conductors can be interconnected, in-cluding bare aluminium or copper mains. The connectors have been tested to relevant standards and are approved for use by Australian power distribution utilities (Consult for further details).

NTD301XFA

NTD101F

LVABC CONNECTORS NTD Series

A2 0107


A3 0107

LVABC CONNECTORS ILC Series

IN-LINE PIERCING CONNECTOR A general purpose in-line piercing connector for aluminium or copper insulated cable in the range 6 - 95 sq mm. • Piercing connectors both sides • Employs proven shear head technology • Fully waterproof • Complies with relevant sections of AS4396 • Fully insulated - no exposed live parts • No crimp tools required • Fits mains box below Installation Notes: Use only a 13mm AF, six point hexagon socket to tighten bolts. All other connections made on the service and consumers cable must also be waterproof to prevent moisture ingress through the cable into the connector.

3 PHASE INDUSTRIAL MAINS BOX FOR IN-LINE PIERCING CONNECTORS • Fully insulated connection system • IP66D rated • Designed to house the ILC 695 (see above) • Fully UV Stabilised • Protects connectors from accidental damage or

contact • Ideal for connecting commercial and industrial

200Amp services • Rear entry of consumer mains cable • Protects consumer mains cables from UV • Water shedding • Attractive design • Supplied complete with 4 x ILC 695 connectors

Product Number

Cable Range (sq mm)

Bolt Head A/F (mm)

Pack Size (pcs)

ILC 695 6 to 95 13 10


Product Number Description

Number of ILC695

connectors included

Pack Size (pcs)

MCB1/2ILC Single phase Industrial MCB supplied with connectors 2 4

MCB3/4ILC Three phase Industrial MCB supplied with connectors 4 4

ILC 695

MCB3/4ILC


DTA TWIN TAP ADAPTOR Use with most IPCs to provide two independent taps.

TT2D SERIES - Twin Tap IPC Mains: Insulated copper or aluminium Branch: Insulated copper or aluminium

MSC SERIES - MULTIPLE SERVICE Mains: Insulated copper or aluminium Bare copper or aluminium Branch: Insulated copper or aluminium * Resealable test point * Reduces pole top congestion * Up to 4 independent taps available

MSCA/50150X

Product Number

Description

Mains Cable Range (mm2) Tap-off Fitting Type Pack Size

TTD1-CCXA 16 to 35 4mm male bayonet 10

TTD2-CCXA 35 to 95 4mm male bayonet 10

TTD3-CCXA 50-150 4mm male bayonet 10

TTDx-CC SERIES - Test / Earth Tap Mains: Insulated copper or aluminium Branch: Bayonet style connecting port

for temporary earths or test points

* includes phase/neutral identification tags

TTD2-CCXA


Product Number

Description

Mains Cable Type

Mains Cable Range (mm2)

Branch Cable Range (mm2)

Pack Size

MSCI/3595X LVABC 25 to 95 4 x 6 to 35 10

MSCI/50150X LVABC 50 to 150 4 x 6 to 35 10

MSCC/795X Bare Copper 7 to 95 4 x 6 to 35 10

MSCC/50150X Bare Copper 50 to 150 4 x 6 to 35 10

MSCA/50150X Bare Aluminium 50 to 150 4 x 6 to 35 10

Product Number

Description


Branch Cable Range (mm2)

Pack Size

TT2D83XF3A 25 to 95 2 x 6 to 35 12

TT2D87XF3A 50 to 150 2 x 6 to 35 12 TT2D87XF3A

DTA2/635

Product Number

Branch Cable Range (mm2) Pack Size

DTA2/635 2 x 6 to 35 12

LVABC CONNECTORS Multi-ports and Earthing

A4 0107

Product Number

Description


Bonding Bolt Size

Pack Size

EPC1-301 25 to 95 M12 12

EPC1-401 50 to 185 M12 12

Both products supplied with suitable IPC

EPC SERIES - Earth/Temporary Bond Mains: Insulated copper or aluminium Bond: To any suitable cable using

integral lug connecting bolt *Fully heat cycle and short circuit tested


A5 0107

LVABC MAINS FUSE SWITCHES

160A, 250A & 400A Fuse Switches The full range of ADC Krone LVABC Fuse Switches • Fully insulated • On-load switching capability • Corrosion resistant connections • One or three pole units available • Suits standard hook stick • Full range of accessories available • Utility Approved

Product Number Rating Poles Cable Range Cable Connection

Method Notes

FSD KGH160/1T 160 A 1 1 x 16-95 sq mm Al/Cu Tunnel type Integral mounting bracket

FSD KGH160/3T-L 160 A 3 1 x 16-95 sq mm Al/Cu Tunnel type Includes mounting bracket

FSD KGH160/3P 160 A 3 1 x 25-95 sq mm Al/Cu IPC type Includes mounting bracket

FSD KGH250/3P 250 A 3 2 x 25-150 sq mm Al/Cu IPC type Includes mounting bracket

FSD KGH400/1L 400 A 1 12mm stud for lug Max lug width 40mm

FSD KGH400/3L 400 A 3 12mm stud for lug Max lug width 40mm, includes mounting bracket

FSD KGH400/3TP 400 A 3 2 x 25-185 sq mm (in) Al/Cu 2 x 25-150 sq mm (out) Al/Cu

Tunnel type (in) IPC type (out) Includes mounting bracket

FSD KGH400/3PT 400 A 3 2 x 25-185 sq mm Al/Cu Pillar terminals

FSD KGH400/3P-LINK 400 A 3 2 x 25-150 sq mm Al/Cu IPC Includes mounting bracket link storage kit fitted to lower housing

Fuse Switches

Full technical specifications available on request.



FCL 400/630 Solid connecting link 400A/630A Size 2

FCL KGH-LINK BOX Connecting-Link Storage Kit (for fitting to lower housing of switch)

FCL 250 Solid Connecting link 250A Size 1

Solid Links

Fuse Cartridges

Product Number Size

FC 160NH00G 00

FC 160NH1G 1

FC 200NH1G 1

Rating

160A

160A

200A

Suitable for FSD

KGH160

KGH250, KGH400

KGH250, KGH400

FC 250NH1G 1 250A KGH250, KGH400

FC 315NH2G 2 315A KGH400

FC 400NH2G 2 400A KGH400

Mounting Brackets


FMB KGH160 Triple pole mounting bracket for three160A fuse switch units, includes hardware

FMB KGH400 Triple pole mounting bracket for three400A fuse switch units, includes hardware

FCA KGH400 Cross arm mounting bracket for one 400A switch fuse unit.

FMB APR630 Mounting bracket for three APR630/1 switches

FUSE SWITCHES ACCESSORIES A6 0107

P/N: FMB KGH160

FCL 250


NEUTRAL BONDING ALTERNATIVES Alternative products for providing for the neutral bond.

The HSC series of connectors have been specially designed to connect consumers mains (house side) to insulated overhead service mains (service side). Fully insulated and equipped with torque control shear-head bolts, the HSC is safe and easy to use. No stripping of insulation is required on the service mains side. The consumers mains side re-quires 17mm of insulation to be stripped.

Product Number

Consumers Mains Cable House side)

(mm2)

Service Side Tap Range (mm2)

Copper Earth Tail

Length (mm)

Lug Hole Size (mm)

Bolt Head A/F

(mm)

Bond-ing Tail

Size (mm2)

Pack Size (pcs)

HSC435 4 to 35 6 to 35 N/A N/A 13 N/A 10

HSC435/1 4 to 35 6 to 35 800 10 13 16 10

HSC435/1O 4 to 35 6 to 35 500 12 13 16 10

HSC435/1P 4 to 35 6 to 35 300 6 13 16 20

HSC435/T 10 sq mm tail 6 to 35 240 N/A 13 N/A 10

HSCH Gripping handle for HSC435 & HSC435/T

HSC SERIES Application: Service side: Insulated copper or aluminium Mains side: Consumers mains (house) cable Features: * Shear heads on both connections * Complies with relevant sections of

AS4396 * Fully bimetallic * Easily fits into Sicame Australia

mains boxes (MCB Series). * Totally insulated and waterproof * IP67 rated Testing Specification: Relevant sections of AS4396 Installation Notes: Use only a 13mm AF, six point hexa-gon socket to tighten bolts. All other connections made on the service and consumers cable must also be waterproof to prevent mois-ture ingress through the cable into the connector.

HSC435

HSC435/T

Product Number

Description

Service Side Tap Range

(mm2)

Copper Earth Tail

Length (mm)

Lug Hole Size (mm)

Bolt Head Stainless Steel A/F

(mm)

TTD101NBKX 6 to 54 800 10 13

TTD101NBKX/12 6 to 54 500 12 13

Pack Size (pcs)

10

10


TTD101NBKX/12

HSCH

SERVICE FITTINGS HSC Series

B1 0107

HSC435/1 HSC435/1O HSC435/1P


The CCW and CAW series of connectors have been specially designed to provide a waterproof connection between insulated overhead services to a variety of bare overhead mains. Both single and double tap models are available.

Product Number

Mains Range Service Taps Pack Size (pcs) Stranding Area

(mm2) OD

(mm) Range (mm2) Quantity

Connectors for Bare Aluminium Mains

CAW35 7/1.75 to 19/3.75 Al 16 to 210 5 to 19 6 to 35 1 12

CAW235 7/1.75 to 19/3.75 Al 16 to 210 5 to 19 6 to 35 2 12

Connectors for Bare Copper Mains

CCW35 7/1.00 to 19/3.00 Cu 5.5 to 135 3 to 15 6 to 35 1 12

CCW235 7/1.00 to 19/3.00 Cu 5.5 to 135 3 to 15 6 to 35 2 10

CAW SERIES Mains: Bare aluminium Service: Insulated copper or aluminium * Piercing connector on service tap * Complies with relevant sections of AS4396 * Disconnection of service by easy removal of

the connector from the mains * Two tap (CAW235) model available * Simple M8 socket operation CCW SERIES Mains: Bare copper Service: Insulated copper or aluminium * Piercing connector on service tap * Complies with relevant sections of AS4396 * Disconnection of service by easy removal of

the connector from the mains * Two tap (CCW235) model available Installation Notes: Use only a 13mm AF, six point hexagon socket to tighten bolts. All other connections made on the service and consumers cable must also be waterproof to prevent moisture ingress through the cable into the connector.


SERVICE FITTINGS CAW and CCW Series

B2 0107

CCW235

CAW35 CAW235

CCW35



Number of HSC435

connectors included

Pack Size (pcs)

MCB1/2H Single phase MCB supplied with connectors 2 10

MCB3/4H Three phase MCB supplied with connectors 4 6

Single and three phase environmental base and cover for the protection of consumer mains suitable for 6 to 35mm2 cable. Each unit contains the HSC series (House Services Connector) providing a fully sealed bimetallic connection of copper consumer mains to Al or Cu services.

MCB SERIES - MAINS CONNECTION BOX * Fully insulated connection system * Plug in HSC’s providing bi-metal connection of

service cables and consumers mains * Base suitable for rear entry of consumers mains * Eliminates UV degradation of PVC consumers

mains * Cover allows for easy exit of bonding tail

HSC435/1 series * Heavy duty polyamide UV stabilised construction * Mains box is IP66 rated * Connectors are IP67 rated

Recommended tool for MCB connectors: RPS13/17-6H or RPS13/17-6SH A small flat blade screw driver is required to remove the MCB cover.

Use only a 13mm AF, six point hexagon socket to tighten the HSC bolts.

SERVICE FITTINGS Mains Connection Boxes

B3 0107

MCB1/2H

MCB3/4H


PFV SERIES SERVICE FUSE HOLDER Application: Insulated XLPE aluminium or copper cables, Suitable for mounting on pole or house using appropriate bracket. Primary House Service Fuse Features: * Range of brackets to suit various applications including re-

placements * Insulation piercing connections on line and load sides * Insulated top mounting M8 shear head bolts * Underside entry cable connection ports creating drip loops on

all installations * Accepts up to 100 amp BS style cartridge (58 x 22mm) * U.V. stabilised polymeric body with anti-flame retardant * Can be ganged to three phases using PFBKT3 or HFBKT3 * U.V. stabilised bird guards over cable seals * Completely waterproof bi-metallic connections. * Stainless steel mounting bolt * IP44 rated Testing Specification: Relevant sections of AS/NZS 60269 Salt fog tracking tests Additional temperature rise tests on service cables not speci-fied in the standard Installation Notes: Use only a 13mm AF, six point hexagon socket to tighten bolts. Do not install old copper cables when corrosion may exist. All other connections made on the service or consumers cable must also be waterproof to prevent moisture ingress through the cable into the fuse holder. PFV100

PFBKT3 3 phase pole

mount bracket

Pole or house mounted fuse holders and accessories. 100 amp single phase, “pig-tail stick” operated, service fuse for house or pole mounting.

PFV100KIT PFVAB1

Recommended tool for PFV100: RPS13/17-6H or RPS13/17-6SH

SERVICE FITTINGS PFV Series

B4 0107

PFBKT1 1 phase pole

mount bracket

MOUNTING BRACKET OPTIONS

HFBKT1 1 phase wall

mount bracket

HFBKT3 3 phase wall

mount bracket


Cable Range (mm2)

Pack Size

PFV100 Fuse Disconnector 100 amp BS style (58 x 22) 6 to 35 20

PFV100KIT Fuse - 100 amp BS style includes PFVAB1 adaptor bracket installed 6 to 35 12

PFV100 695 Fuse Disconnector 100 amp BS style (58 x 22) 6 to 95

ACCESSORIES

Product Number Description Pack Size

PFBKT1 Pole bracket single phase 20

PFBKT3 Pole bracket three phase 15

HFBKT1 House bracket single phase 20

HFBKT3 House bracket three phase 15

PFVAB1 Adaptor bracket to fit PFV100 to swan neck pin 40

FUSE BS100 100 amp BS Cartridge (58x22mm) 1


MJPB SERIES * Non-tension 4 to 35mm2 range * Suitable for copper or aluminium

Product Number

Service Cable Size (mm2)

Hex Die A/F (mm)

MJPB4 4 4 14

MJPB6-4 6 4 14

MJPB6 6 6 14

MJPB10-6 10 6 14

MJPB10 10 10 14

MJPB16-6 16 6 14

MJPB16-10 16 10 14

MJPB16 16 16 14

MJPB25-6 25 6 14

MJPB25-10 25 10 14

MJPB25-16 25 16 14

MJPB25 25 25 14

MJPB35-6 35 6 14

MJPB35-10 35 10 14

MJPB35-16 35 16 14

MJPB35-25 35 25 14

MJPB35 35 35 14

Crimp width: 9 mm

Standard pack size: 10 pcs

Pack Size

10

10

10

10

10

10

10

10

10

10

10

10

10

10

10

10

10

Pre-insulated compression sleeves for joining LVABC services and mains.

MJPT SERIES * Limited and full tension 25 to 150mm2 range * Suitable for copper or aluminium

Product Number

Mains Cable Size (mm2)

Hex Die A/F (mm)

MJPT25 25 25 17.3

MJPT35-25 35 25 17.3

MJPT35 35 35 17.3

MJPT50-25 50 25 17.3

MJPT50-35 50 35 17.3

MJPT50 50 50 17.3

MJPT70-35 70 35 17.3

MJPT70-50 70 50 17.3

MJPT70 70 70 17.3

**MJPT95 95 95 17.3

MJPT95-21 95 95 21.5

MJPT120 120 120 21.5

**MJPT150 150 150 21.5

** Limited tension fittings When tested to AS3766, test load achieved is:- MJPT95SF: 7kN, MJPT95-21SF: 16.8kN All crimps 9mm in width

Standard pack size: 10 pcs

Pack Size

10

10

10

10

10

10

10

10

10

10

10

10

10

MJPB

MJPT Recommended tool for MJPB connectors: MP-10 SIMPI

MP-10 SIMPI

Recommended tool for MJPT connectors: Use any mechanical or hydraulic action crimp tool capable of accepting 9mm wide hexagonal crimp dies, with an across flats (AF) as specified in chart above. Minimum tonnage at die face recommended at 5 tonne.

PRE-INSULATED FITTINGS MJPB and MJPT Series C1

0107


MJPB SERIES PRE-CRIMPED * Non-tension 4 to 35mm2 range * Suitable for copper or aluminium

Pre-insulated compression sleeves with pre-crimped, PVC insulated copper tails

Product Number Service Cable Size

Copper or Aluminium

(mm2 )

Pre-crimped PVC insulated copper tail Hex Die AF (mm)

Pack Size Size

(mm2) Insulation Ribs Length (mm)

MJPB25-10+CABLE 25 10 None 225 14 20

MJPB25-10+(N)CABLE 25 10 1 rib for neutral identification 225 14 20

MJPB25-16+CABLE 25 16 None 225 14 20

MJPB25-16+(N)CABLE 25 16 1 rib for neutral identification 225 14 20

Crimp width: 9mm for all products

APPLICATION TOOLING Product Number: MP-10 SIMPI * One-hand operation * Specifically designed for MJPB series and other pre-insulated products * Captive dies * Non-hydraulic * Hexagonal crimp AF: 14mm * Hexagonal crimp width: 9mm

MP-10 SIMPI

Recommended tool for all products: MP-10 SIMPI

PRE-INSULATED FITTINGS Pre-crimped sleeve & tools

C2 0107


MEPCNA SERIES * Pre-crimped with bare aluminium tail * End cap on tail provided to prevent fraying * Used for terminating LVABC into switchgear * Used for connecting LVABC to open wire bare

conductor

Product Number

Cable Size

(mm2)

Aluminium Tail Size

(mm2) Die A/F (mm)

Crimp Width (mm)

MEPCNA16 16 35 14.0 9

MEPCNA16-17 16 35 17.3 9

MEPCNA25 25 35 14.0 9

MEPCNA25-17 25 35 17.3 9

MEPCNA35 35 55 17.3 9

MEPCNA50 50 55 17.3 9

MEPCNA70 70 55 17.3 9

MEPCNA95* 95 75 17.3 9

MEPCNA150* 150 75 21.5 9

* 75 deg C current rating: 250A

Pack Size

100

100

MEPCNA

MEPCNU

MEPCNU SERIES * Pre-crimped with bare copper tail * End cap on tail provided to prevent fraying * Used for terminating LVABC into switchgear * Used for connecting LVABC to open wire bare

conductor

Product Number

Cable Size (mm2)

Copper Tail Size (mm2)

Die A/F (mm)

Crimp Width (mm)

MEPCNU16 16 35 14.0 9

MEPCNU16-17 16 35 17.3 9

MEPCNU25 25 35 14.0 9

MEPCNU25-17 25 35 17.3 9

MEPCNU35 35 55 17.3 9

MEPCNU50 50 55 17.3 9

MEPCNU70 70 55 17.3 9

MEPCNU95* 95 75 17.3 9

MEPCNU150** 150 75 21.5 9

*75 Deg C current rating: 250A **75 Dec C current rating: 370A

Pack Size

100

100

50

Recommended tool for MEPCNU16, MEPCNA16, MEPCNU25, MEPCNA25: MP-10 SIMPI. All other MEPCN series products: Any compression tool with min 5t output fitted with hexagonal compression dies as specified above.

MP-10 SIMPI

PRE-INSULATED FITTINGS Pre-crimped sleeve & tools

C3 0107


CPTAU SERIES BI-METALS * Suits aluminium LVABC and other

insulated compacted aluminium cables

* Round copper palm * Suitable for connecting aluminium

cables to switchgear, bus bars etc.

Product Number

Cable Size

(mm2)

Lug Dimensions (mm) Hex Die

A/F (mm)

Die Width (mm)

Overall Length (L)

(mm) Palm Hole

Size

Outside Palm

Diameter (mm)

CPTAU16 16 87 M10 20 14.0 9

CPTAU25 25 87 M10 20 14.0 9

CPTAU25-17 25 92 M10 25 17.0 9

CPTAU25-12.5DIA 25 87 M12 20 14.0 9

CPTAU35 35 92 M12 25 17.3 9

CPTAU50 50 92 M12 25 17.3 9

CPTAU70-21 50 115 M12 25 21.5 9

CPTAU95 95 92 M12 25 17.3 9

CPTAU95-21 95 115 M12 30 21.5 9

CPTAU150 150 115 M12 30 21.5 9

Pack Size (pcs)

10

10

10

10

10

10

10

10

10

10

A complete range of pre-insulated bi-metal and aluminium lugs for the termination of LVABC.

L

Product Number

Cable Size

(mm2)

Lug Dimensions (mm) Hex Die

A/F (mm)

Die Width (mm)

Overall Length

(L) (mm)

Palm Hole Size

Palm (W x D) (mm)

CPTA25 25 100 M12 32 x 33 14.0 9

CPTA35 35 110 M16 32 x 33 17.3 9

CPTA50 50 110 M16 32 x 33 17.3 9

CPTA95 95 110 M16 32 x 33 17.3 9

CPTA150 150 130 M16 37 x 37 21.5 9

Pack Size

(pcs)

10

10

10

10

10

CPTA SERIES ALUMINIUM *Suits aluminium LVABC and other insulated

compacted aluminium cables * Square aluminium palm * Suitable for connecting aluminium cables to

switchgear, bus bars etc.

W

L

D

Recommended tool for up to 25 mm2: MP-10 SIMPI , larger sizes: any compression tool with min 5t output fitted with hexagonal compression dies as specified above.

Recommended tool for up to 25 mm2: MP-10 SIMPI , larger sizes: any compression tool with min 5t output fitted with hexagonal compression dies as specified above.

C4 0107

PRE-INSULATED FITTINGS CPTAU and CPTA Series


Product Number

Number of

Connection Ports

Conductor Size

(mm2)

Bolt Head Size (mm)

MUCI4/650 4 6 to 50 13

MUCI3/650 3 6 to 50 13

MUCI2/650 2 6 to 50 13

MUCIBOLTYEL-LOW 13-17

(spare yellow shear head bolt)

N/A N/A 13

MUCI/H Gripping handle for MUCI4/650 & MUCI2/650

Pack Size (pcs)

12

6

20

1

Multi-tap insulation piercing connectors for underground connection of two, three or four insulated cables.

MUCI3/650


MUCI SERIES SUBMERSIBLE CONNECTORS Application: For the waterproof, underground connection of 2, 3 or 4 ca-bles. Suitable for copper or aluminium insulated cables, sin-gle or double insulated from 6 to 50 sq mm. Ideal for connect-ing cables in pillar boxes, buried connection pits and street-light columns. Features: * Fully submersible and totally waterproof. * Torque controlling shear head bolts for correct contact pres-

sure. * Insulation piercing on all cable taps. * No need to strip cable. * Flexible sealing cable ports that are not affected by the an-

gle of cable entry. * Fitted with push-on protective bolt caps. * IP67 rated Testing Specifications: Tested to ANSI C119.1-1986 Tested to URD Pit Connector Technical Specification (Vic). Application Notes: Use only a 13mm AF, six point hexagon socket to tighten bolts. All other connections made on cables connected with this product must also be waterproof to prevent moisture ingress through the cable into the connector. 50 sq mm SDI may require the removal of the outer sheath, depending on insulation thickness and conductor compaction. The port sealing cap should be left in place when connecting 6 sq mm cables and removed for larger sizes Cables less than 6 sq mm may be connected by doubling over the last 2cm of cable prior to insertion. The port sealing cap should also be left in place. Each cable port should be only used twice. The blue bolt must be replaced with a yellow bolt to identify the second use of a cable port.

MUCIBOLTYELLOW 13-17 MUCI/H

UNDERGROUND CONNECTIONS MUCI Series D1

0107

MUCI2/650

MUCI4/650


D2 0107

UNDERGROUND CONNECTIONS Resin Filled Service Tee Joint

PRODUCT NUMBER: HSM 270/140 RESIN FILLED TEE JOINT Application: For the waterproof, underground connection of low voltage services to low voltage mains distributor cables. Features: • Easy to apply ‘ring’ style connector • Suitable for copper or aluminium cables • Compact, low volume joint • Suitable for direct burying • Safe, mix in the bag two part resin • No special tools required • Suitable for a wide range of popular cable types • Supplied complete with all necessary components for

one complete Tee Joint Kit Components: • Multi-phase ring connector • Clear plastic encapsulating shell • Encapsulating shell sealing kit • Double chamber, mix in the bag resin system (1 bag) • Protective mixing gloves and cloth • Abrading paper • Installation instructions Testing Specifications: To international standards FULL SPECIFICATIONS, TEST REPORTS AND INSTALLTION INSTRUCTIONS ARE AVAILABLE ON REQUEST

Specification Value Acceptable mains cables; -Aluminium 4 core XLPE/PVC solid sector -Aluminium 4 core XLPE/PVC stranded sector (not suitable for 3 core sector cables)

95 (min) – 240 (max) mm2 95 (min) – 185 (max) mm2

Acceptable service (branch) cables; Copper or aluminium 4 core circular stranded:- -Single service or branch -Double service or branch

6 (min) – 95 (max) mm2 6 (min) – 25 (max) mm2

Mains cable contact screw tightening torque 20 Nm

Service cable screw tightening torque 14 Nm

Tool required for tightening contact screws 5mm AF hexagonal allen key or ‘T’ handled box wrench. TBOX 5MM

Specifications - ring connector

Specification Value

Overall dimensions of completed joint, excluding cables

305mm (length) 140mm (width at widest point) 185mm (height)

Weight (with resin, excluding cables) 4.7 kg

Maximum overall diameter of main cable 54mm Maximum overall diameter of service cable 40mm

Maximum number of service cables Two 4 core cables

Volume of resin required 3 litres (nominal)

Waste disposal Waste packaging may be dis-posed of as normal landfill.

Specifications - Completed Joint

Sealing kit

Ring Connector

Mix in the bag resin system

TBOX 5MM JTN/2 core separator

Recommended tools

HSM 270/140


Product Number

Connections Main Cable Range Maximum

Tap Size Mains Tap

BF-1A 2 2 120 solid Al.

120 stranded Al. 240 solid Al.

240 stranded Al.

2 x 50mm² Cu. 6

BF-1A/SYD 2 2 120 solid Al.


240 stranded Al.

2 x 50mm² Cu. 8

TF-2A 3 3 120 solid Al.


240 stranded Al.

3 x 50mm² Cu. 6

TF-2A/SYD 3 3 120 solid Al.


240 stranded Al.

3 x 50mm² Cu. 8

Service Tap Stud Size (mm)

Pack Size

20

20

20

20

Mechanical connectors for use on sector shaped U/G cables.

BF & TF SERIES BI-FORM AND TRI-FORM MECHANICAL CONNECTORS: * Accepts 185 and 240mm² 4 core solid

or stranded aluminium sector cables to AS1125.

* Accepts up to two 50mm² copper tap-off connections. (3 for TF-2A connector)

* Available in “BI-FORM” or “TRI-FORM” form which allows either two sector ca-ble connections (normal loop type pillar) or three connections (three way loop pillar).

* Shear-head screw on main cable con-nections provide correct tightening of bolts and ensure trouble free operation.

* No special tools needed for installation, just a spanner!

* Compact dimensions allow standard protective covers to be used.

* Fully tested to standard BS4579 “Specification for performance or me-chanical and compression joints in elec-tric cable and wire connectors” (2000 heat cycles).

TF-2A/SYD

UNDERGROUND CONNECTIONS BF-1A and TF-2A Series D3

0107

BF-1A/SYD


Mains conductor size (mm2)

Branch Conduc-

tor Size

(mm2)

70 95 120 150 185 240 300

70

95

120

150

185

240

300

BSTA/1 All connectors BST/A2, BSTA/3

Product Numbers:

The combinations in the table above are valid for conductors of the same sector shape, i.e. 4 core to 4 core, or 3 core to 3 core. Should mixed combinations be required, we suggest that verification of the products suitability be obtained prior to use. Packed individually in plastic bags

BST/A SERIES Application: Branch connections to mains cables Conductor Type: 3 or 4 core solid sector aluminium Hexagonal head screw available as an option. Add suffix ‘H’ to product number. Eg BST/A3H

3/16 “ AF hex drive required

LVM SERIES Application: General purpose branch or service connections. Conductor Types: Most conductor types including solid or stranded, circular or shaped, copper or aluminium. Stranded service conductors of 16 mm2 or below should be doubled and re-doubled where necessary to achieve a satisfactory cross sectional area. Shear head caps are available as an option. Packed individually in plastic bags

Product Number Conductor Size Range (mm2) Overall

Length (A)(mm)

Width (B) (mm) Mains / Service Mains / Branch /

Service

LVM1 16—95 16—95 45 34

LVM2 16—185 16—185 45 44

LVM3 16—300 16—300 50 54

All connectors are electro-tinned. Brass gauze is not necessary for copper conductors

UNDERGROUND CONNECTIONS Mechanical Connectors D4

0107

LVM3


MF SERIES Application: Straight through joint for 3 or 4 core sector shaped solid or stranded aluminium, and stranded copper conductors. Features: All connectors feature a shear head bolt for bolting torque control. Pressure pads are included for stranded con-ductor connectors. MF1 and MF3 types are supplied with brass gauze for connection of copper conductors. When connecting copper conductor, the brass gauze supplied with connector should be wrapped around the copper conductor prior to bolting. MF3 type connectors include pressure pad for stranded side only. Packed individually in sealed plastic bags

Product Number

Conductor Size Range (mm2)

Overall Length (A)

(mm)

Width (B) x Height (C)

(mm)

Hex Head AF

(mm)

Connectors for joining STRANDED sector to STRANDED sector shaped conductors

MF1/1 50—95 80 25x25 13

MF1/2 95—185 100 34x33 17

MF1/3 185—300 120 40x41 17

MF1/4 300—500 120 48x51 19

MF1/3A 150—300 120 40x41 17

Connectors for joining SOLID sector to SOLID sector shaped conductors

MF2/1* 50—95 80 25x25 13

MF2/2* 95—185 100 34x33 17

MF2/3* 185—300 120 40x41 17

Connectors for joining STRANDED sector to SOLID sector shaped conductors, in either orientation

MF3/1 50—95 80 25x25 13

MF3/2 95—185 100 34x33 17

MF3/3 185—300 120 40x41 17

MF3/3A 185—300 stranded

70—185 solid 120 40x41 17

* MF2 types not supplied with brass gauze.

MF1/3G 240-240 only 120 40x41 17

MF3/3D 240 only 120 40x41 17

Pack Size

1

1

1

1

1

1

1

1

1

1

1

1

1

1

MF1/3H 240-185 only 120 40x41 17 1

MF1 Type Connector

MF3 Type Connector



0107


UM SERIES Application: Straight-through joint for 3 or 4 core sector shaped solid or stranded aluminium, and stranded copper conductors. Features: The UM series feature a removable bridge, allowing the conductor to be easily positioned into the connector. All connectors feature a shear-head bolt for bolting torque control. Pressure pads are included for connecting stranded conductors and should be discarded when connecting solid core conductors. All UM series connectors are supplied with brass gauze for connection of copper conduc-tors. When connecting copper conductor, the brass gauze supplied with connector should be wrapped around the copper conductor prior to bolting. Packed individually in sealed plastic bags

Product Num-ber


Overall Length (B)

(mm)

Width (A) x Height (C)

(mm)

Hex Head AF

(mm)

Application range for STRANDED 3 or 4 core sector shaped aluminium conductors

UM1 35—95 90 26x32 17

UM2 95—150 100 31x36 17

UM3 185—300 130 42x45 17

Application range for SOLID 3 or 4 core sector shaped aluminium conductors

UM1 70—95 90 26x32 17

UM2 95—150 (3 core) 95—185 (4 core) 100 31x36 17

UM3 185—300 130 42x45 17

Application range for STRANDED circular copper or aluminium conductors

UM1 35—95 90 26x32 17

UM2 95—120 100 31x36 17

UM3 120—300 130 42x45 17

UM300 95-300 120 41x40 17

All connectors in the series are supplied with brass gauze

UM300 95—300 120 41x40 17

UM300 95-300 120 41x40 17

Pack Size

1

1

1

1

1

1

1

1

1

1

1

1



0107


MF15 SERIES CONNECTORS WITH CENTRE BARRIER Application: Straight-through jointing of stranded or solid, cir-cular or sector shaped copper or aluminium con-ductors. The circular profile of the connector makes them especially suited to 11kV & 22kV cable joints. Features: The MF15 series of bolted connectors feature an integral centre moisture barrier and utilises the patented “universal” range taking shear-head bolts. The connector is shipped complete with core stripping guides and brass gauze for the jointing copper conductors. When using these connectors in HV joints, it is essential that the jointing system supplier’s in-structions for stress relieving and re-insulation techniques are strictly adhered to. Packed individually in sealed plastic bags Test Specifications: ER C79 IEC 1238-1 AS/NZS 4325.1

Product Number


Overall Length (L)

(mm)

Diameter (ΦB) (mm)

Bolt Size (ΦC)

Application range for STRANDED SECTOR shaped conductors

MF15/1 16 to 120 95 28.5 M16

MF15/2 16 to 185 105 32.0 M16

MF15/3 70 to 300 115 37.5 M18

Application range for SOLID SECTOR shaped conductors

MF15/1 16 to 95 95 28.5 M16

MF15/2 16 to 150 105 32.0 M16

MF15/3 70 to 240 115 37.5 M18

Application range for STRANDED CIRCULAR conductors

MF15/1 16 to 120 95 28.5 M16

MF15/2 16 to 185 105 32.0 M16

MF15/3 70 to 300 115 37.5 M18

MF15/EDF 95 to 240 105 32.0 M16

Application range for SOLID CIRCULAR conductors

MF15/1 16 to 95 95 28.5 M16

MF15/2 16 to 150 105 32.0 M16

MF15/3 70 to 240 115 37.5 M18

Pack Size

1

1

1

1

1

1

1

1

1

1

1

1

1

Required tool for all products: JTS/16 Splined socket with RPS13/17-6H or RPS13/17-6SH.

JTS/16 RPS13/17-6H

UNDERGROUND CONNECTIONS Mechanical Connectors

D7 0107


MF17 SERIES CONNECTORS WITHOUT CENTRE BARRIER Application: Straight-through jointing of stranded or solid, circular or sector shaped copper or aluminium conductors. The circular profile of the connector makes them especially suited to 11kV & 22kV cable joints. Features: The MF17 series bolted connectors utilise the patented “universal” range taking shear-head bolts and comes complete with core stripping guides. Supplied with brass gauze for the jointing of cop-per conductor. When using these connectors in HV joints, it is essential that the jointing system supplier’s in-structions for stress relieving and re-insulation techniques are strictly adhered to. Packed individually in sealed plastic bags Test Specifications: ER C79 IEC 1238-1 AS/NZS 4325.1

Product Number


Overall Length (L)

(mm)

Diameter (ΦB) (mm)

Bolt Size (ΦC)

Application range for STRANDED SECTOR shaped conductors

MF17/1 10* to 95 90 28.5 M16

MF17/2 16 to 95 100 32.0 M16

MF17/3 70 to 300 110 35.0 M18

MF17/4 185 to 300 110 41.0 M18

Application range for SOLID SECTOR shaped conductors

MF17/1 10 to 70 90 28.5 M16

MF17/2 16 to 150 100 32.0 M16

MF17/3 70 to 240 110 35.0 M18

MF17/4 185 to 300 110 41.0 M18

Application range for STRANDED CIRCULAR conductors

MF17/1 10* to 95 90 28.5 M16

MF17/2 16 to 185 100 32.0 M16

MF17/3 70 to 300 110 35.0 M18

MF17/4 185 to 300 110 41.0 M18

Application range for SOLID CIRCULAR conductors

MF17/1 10 to 70 90 28.5 M16

MF17/2 16 to 150 100 32.0 M16

MF17/3 70 to 240 110 35.0 M18

MF17/4 185 to 300 110 41.0 M18 *Conductor cores 10 sq mm and below should be doubled to achieve necessary cross sec-

tional area.

Pack Size

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

1

Required tool for all products: JTS/16 Splined socket with RPS13/17-6H or RPS13/17-6SH. JTS/16 RPS13/17-6H


D8 0107


ML SERIES BOLTED LUGS Application: Termination of stranded or solid, circular or sector shaped, aluminium or copper cables. Features: * Shear-head bolts for torque control * No specialised compression tools

required * Supplied with brass gauze for copper con-

ductors Test Specifications: BS4579, including short circuit test ER C79

Product Number

Conductor Size Range

(mm2) Stud

Size (E)

Overall Length

(A) (mm)

Palm Width

(B) (mm)

Barrel Height

(C) (mm)

ML1-12 50 to 95 M12 95 32.0 25.0

ML1-16 50 to 95 M16 95 32.0 25.0

ML2-12 120 to 185 M12 125 34.0 32.5

ML2-16 120 to 185 M16 125 34.0 32.5

ML3-12 240 to 300 M12 145 40.0 41.0

ML3-16 240 to 300 M16 145 40.0 41.0

ML4 400 to 500 M16 155 47.5 51.0

Hex head bolt AF is 17mm for all products.

Pack Size

1

1

1

1

1

1

1



D9 0107


* Sector core dimensions to BS 6791 only

MAINS BRANCH CONNECTORS Mechanical Connectors D10

0107

Principal Application

Product Number

Conductor Range Size (mm2) 3 or 4 core stranded sector

Main Branch

Min. Max. Min. Max.

WB1 150 300 150 300 425

WB2 300 500* 300 500* 505

WB3 300 500 150 300 490

Weight (g)

WB1, 2 & 3 SERIES - Mains to Mains Branch Connectors Principal Applications Designed to accommodate three or four core sector shaped stranded conductors in the ranges specified in the table. Ease of fitting and simplicity of use were fundamental objectives adopted in the design of these connectors. The shear head screw principle ensures that a reliable and consistent connection is achieved without the need for specialised tooling. Each connector is supplied in a sealed pack together with fitting instructions, details of which are below.

Secondary Application

Conductor Range Size (mm2)

Stranded circular

Main Branch

Min. Max. Min. Max.

WB1 95 240 120 300

WB2 185 300 240 400

WB3 185 300 120 300

Product Number

Dimensions

A B C D

WB1 82 60 67 19

WB2 93 60 72 19

WB3 91 60 68 19

Product Number

Physical Dimensions For both principal and secondary applications. Material: Aluminium Alloy

Secondary Applications These connectors can accept stranded circular conductors (copper or aluminium) in the main and/or branch sides of

Fitting Instructions - A 19mm AF hex socket is required Separate the main cable cores sufficiently to allow yoke section to be fitted around the conductor and strip the insulation from the core equal to the connector length plus 10mm. Thoroughly abrade the exposed conductor and loosely assemble the lower limb (mains side) of the connector around the core by fitting the bridge piece, inserting the pressure pad and tightening the mains screws until the connector is positively located. Set and locate the branch core, then cut to length, strip insulation to suit and thoroughly abrade the exposed conductor before assembling into the connector as described above. Complete the operation by tightening down the mains screws consecutively, one turn at a time, until both heads shear. Repeat the operation for the branch screws. If copper conductors are to be jointed, they should be wrapped in brass gauze in order to improve the electrical stability of the interface connection.



Product Number

Conductor Range Size (mm2) Primarily for 4 core stranded

sector

Main Branch

Min. Max. Min. Max.

WB4 150 300 185 300 410

Weight (gms)

MAINS BRANCH CONNECTORS Mechanical Connectors

D11 0107

WB4 Mains Branch connector Principal application Primarily for four core sector shaped stranded cables, in both copper and aluminium. The branch channel designed to accept the branch conductor in any orientation to suit any particular joint configuration. Shear-head screws ensure that the correct clamping pressure is applied to give reliable connection, eliminating the need for the use of specialised tools on site. The connector is supplied individually packed, complete with fitting instructions, full details of which are below. Brass gauze can be supplied upon request for use with copper conductors.



Stranded circular

Main Branch

Min. Max. Min. Max.

WB4 95 240 150 300

Product Number

Secondary Principal Suitable for stranded circular conductors.

Physical Dimensions Material: Aluminium alloy

Fitting Instructions Separate the main cable cores to enable the main channel of the connector to be fitted around the conductor. Strip 70mm length of insulation (connector length plus 10mm) from the core at the selected connection position. Thoroughly abrade the exposed section of the conductor, pass the lower channel (mains side) of the connector yoke around the conductor and loosely assemble by inserting the pressure pad and bridge piece. Tighten the screws until the connector is positively located on the main but do not shear off the screw heads at this stage. Set the branch core and cut the required length. Strip the insulation to suit and thoroughly abrade the exposed conductor. Assemble as for the main connection. Complete the operation by tightening the mains screws consecutively, one quarter of a turn at a time, until both heads are sheared. Repeat the operation for the branch side. If copper conductors are to be jointed, they should be wrapped in brass gauze before insertion into yoke.



SERVICE BRANCH CONNECTORS Mechanical Connectors D12

0107

WS2 - Mains to Service Branch Connector Principal Applications Designed to accommodate solid or stranded service conductors to a maximum of 95mm2, from four core stranded sector shaped mains conductors in the range 120-185mm2. The connector employs the proven shear-head screw principal to ensure that a consistent and reliable connection is achieved. Fitting is com-pleted by the use of orthodox hand tools only. No specialised equipment or techniques are required. Each connector is supplied in a sealed pack together with fitting instructions, details of which are below.



Stranded circular sector conductor

Main Branch

Min. Max. Min. Max.

WS2 70 120 16 70

Product Number

Secondary Applications Can accept stranded circular conductors (copper & aluminium) in the main and/or branch sides of the connector.

Physical Dimensions Material: Aluminium alloy.


Product Number


Main 4 core stranded

sector

Branch Solid or

Stranded

Min. Max. Min. Max.

WS2 120 185 16* 95 160

Weight (gms)

*Note - for small section conductors see fitting instructions below

Fitting Instructions Separate the main cable cores sufficiently to allow the yoke section to be fitted around the conductor and strip the insulation from the core equal to the connector length plus 10mm. Thoroughly abrade the exposed conductor and loosely assemble the connector around the core by fitting the bridge piece, inserting the pressure pad and tightening the mains screw until the connector is positively located. Cut the branch con-ductor to length, strip the insulation to suit, then thoroughly abrade and assemble the core into the connector by fitting the bridge piece and pressure pad, and tightening down the service screws to hold the conductor in position. Complete the operation by tightening down the mains screws until the heads shears, then finally tightening the service screws consecutively, one turn at a time, until both heads are sheared. It is suggested that conductors below the minimum range requirement of 16mm2 are doubled and, if needed, redoubled to achieve the required cross sectional area and, if copper conductors are to be jointed, they should be wrapped in brass gauze in order to improve the electrical sta-bility of the interface connection.



SERVICE BRANCH CONNECTORS Mechanical Connectors

D13

0107

WS3 - Mains to Service Branch Connector Designed to accommodate solid or stranded service conductors to a maximum of 95mm2, from four core stranded sector shaped mains conductors in the range 120-185mm2. The connector employs the proven shear-head screw principal to ensure that a consistent and reliable connection is achieved. Fit-ting is completed by the use of orthodox hand tools only. No spe-cialised equipment or techniques are required. Each connector is supplied in a sealed pack together with fitting instructions, details of which are included in the technical data below. Material: Aluminium Alloy

Product Number


Weight (gms)

Main 4 core

stranded

Branch Solid or stranded

Min. Max. Min. Max.

WS3 240 300 16* 95 190

Physical Dimensions

Fitting Instructions Separate the main cable cores sufficiently to allow the yoke section to be fitted around the conductor and strip the insulation from the core equal to the connector length plus 10mm. Thoroughly abrade the exposed conductor and loosely assemble the connector around the core fitting the bridge piece, inserting the pressure pad and tightening the mains screw until the connector is positively located. Cut the branch con-ductor to length, strip the insulation to suit, then thoroughly abrade and assemble the core into the connector by fitting the bridge piece and pressure pad, and tightening down the service screws to hold the conductor in position. Complete the operation by tightening down the mains screws until the heads shears, then finally tightening the service screws consecutively, one turn at a time, until both heads are sheared. It is suggested that conductors below the minimum range requirement of 16mm2 are doubled and, if needed, redoubled to achieve the required cross section area and, if copper conductors are to be jointed, they should be wrapped in brass gauze in order to improve the electrical stability of the interface connection.

* Note - for small section conductors see fitting instructions below

Dimensions (mm)

A B C D E

WS3 66.5 40 49 13 17

Product Number




0107


Product Number


Main (4c sector stranded) Branch

Min. Max. Min. Max.

WS4 240 300 2 x 50

(circ) 2 x 95 (circ)

260 240 300 95

(sector) 185

(sector)

Weight (g)

WS4 - Mains to Service Branch Connector Principal Application Designed to accommodate a double service configura-tion to a maximum of two 95mm2 stranded conductors, off four core stranded sector shaped mains conductors in the range 240-300mm2. The connector employs the proven shear-head screw principal to ensure that a consistent and reliable con-nection is achieved. Fitting is completed by the use of orthodox hand tools only. No specialised equipment of techniques are required. Each connector is supplied in a sealed pack together with fitting instructions, details of which are included in the technical data below.

Secondary Applications (a) Single Branch Connections WS4 connector is also suitable for single branch connections in the range 95-185mm2 (sector shaped conductors). (b) Circular Conductors WS4 can accept stranded circular (aluminium or copper), in the mains and/ or branch sides. Material: Aluminium Alloy



Main (Circular)

Branch (Circular)

Min. Max. Min. Max.

WS4 120 185 1 x 50 or 2 x 50

1 x 150 or 2 x 70

Product Number

Fitting Instructions Separate the main cable cores sufficiently to allow the yoke section to be fitted around the conductor and strip the insulation from the core equal to the connector length plus 10mm. Thoroughly abrade exposed conductor and loosely assemble the connection around the core by fitting the bridge piece, inserting the pressure pad and tightening the mains screw until the connector is positively located. Cut the branch con-ductor to length, strip the insulation to suit, then thoroughly abrade and assemble the core into the connector by fitting the bridge piece and pressure pad, and tightening down the service screws to hold the conductor in position. Complete the operation by tightening down the mains screws until the head shears, then finally tightening the service screws consecutively, one turn at a time, until both heads are sheared. If cop-per conductors are to be jointed, they should be wrapped in brass gauze in order to improve electrical stability of the interface connection.

Physical Dimensions

Dimensions (mm)

A B C D E

WS4 70 50 49 17 17

Product Number




0107


Product Number

Conductor Range Size (mm2) For solid or stranded sector

Main (4c stranded sector)

Branch (solid or stranded)

Min. Max. Min. Max.

WS5 400 500 16* 95 225

Weight (g)

*Note - for small section conductors see fitting instructions below.

WS5 - Mains to Service Branch Connector Principal Application Designed to accommodate solid or stranded service conductors to a maximum of 95mm2, from four core stranded sector shaped mains conductors in the range 400-500mm2. The connector employs the proven shear-head screw principal to ensure that a consistent and reliable connection is achieved. Fitting is com-pleted by the use of orthodox hand tools only. No specialised equipment or techniques are required. Each connector is supplied in a sealed pack together with fitting instructions, details of which are included in the technical data below.



Main (circular)

Branch (circular)

Min. Max. Min. Max.

WS5 240 400 16 70

Product Number

Secondary Application WS5 connector can accept stranded circular con-ductors (aluminium or copper) in the main and/ or branch sides of the connector. Material: Aluminium alloy

Fitting Instructions Separate the main cable cores sufficiently to allow the yoke section to be fitted around the conductor and strip the insulation from the core equal to the connection length plus 10mm. Thoroughly abrade expose conductor and loosely assemble the connector around the core by fitting the bridge piece, inserting the pressure pad and tightening the mains screw until the connector is positively located. Cut the branch conductor to length, strip the insulation to suit, then thoroughly abrade and assemble the core into the connector by fitting the bridge piece and pressure pad, and tightening down the service screws to hold the conductors in positions. Complete the operation by tightening down the mains screws until the head shears, then finally tightening the service screws consecutively, one turn at a time, until both heads are sheared. It is suggested that conductors below the minimum range requirement of 16mm2 are doubled and, if needed, redoubled to achieve the required cross sectional area and, if copper conductor are to be jointed, they should be wrapped in brass gauze in order to improve the electrical stability of the inter-face connection.

Physical Dimensions

Dimensions (mm)

A B C D E

WS5 73 40 55 13 17

Product Number



UGT Series Underground Warning Tapes Application: Suitable for use in conjunction with underground electrical services as a means of indicating its proximity. Features: • Made from polyethylene • Minimum 25mm print size on tape • Colours comply with AS 2700 Testing Specifications: Manufactured and tested to the requirements of AS/NZS 4275:1995.

Product Number

Description

Type / Marking Colour Width (mm)

Length (m)

UGT-E Electrical ORANGE 150 350

UGT-C Communications WHITE 150 350

UGT-G Gas YELLOW 150 350

Pack Size

1 Roll

1 Roll

1 Roll

UGT-E

PROTECTIVE COVERS D16 0107

Overhead Line Covers (Tigertails™) Tested to comply with AS-4202, Class 1 insulating covers Product Number

Dimensions (mm)

Length Diameter

TIGER TAIL DB35A 2600 35

Linesman Safety Covers Tested to comply with AS-4202 Class 2 insulating material

Product Number

Dimensions (mm)

Length Width

LSC225 1200 225

LSC300 1200 300

LSC375 1200 375

Underground Pit Connections Safety Cover • Designed to fit into most commonly used distribution service pits. • Provides an additional insulating barrier of safety for the pit connec-

tions if the main pit cover is removed or damaged. • Provided with an eyelet for safe extraction by service personnel. • Orange in colour, with “Danger Electricity” moulded into the unit. (Illustrative Only)


These tools provide linesmen with a reliable means of installing all insulation piercing connectors.

Product No: CIE100 Core separation tool suitable for LVABC up to and including 4 x 95mm².

Product No: PMR87 Core separation wedge suitable for LVABC up to and including 4 x 95mm². PMR87

TOOLS AND ACCESSORIES Spanners, testers, wedges and allen key

E1 0107

Product No: TBOX 5MM T handled 5mm allen key driver, insulated handle. Suitable for popular tee joint style ring connectors.

Product No: RPS13/17-6H The spanners have the following features: * 13mm across flats and 17mm across flats in one spanner. * Reversible ratchet. * Suits all sizes of insulation piercing connectors (TTD and NTD) for cables

1.5mm² up to 240mm², most strain clamps and some suspension clamps. * 6 point hex (double sided) * Overall length 267mm Product No: RPS13/17-6SH. Short handled version of above. Overall length 197mm.

Product No: PPI514 Re-usable insulated cable test point. Suitable for cable ranges up to 150mm².

RPS13/17-6H

PPI514

CIE100


TOOLS AND ACCESSORIES Cutters, Strippers & Testers

Product No: RCC-42 ratchet cable cutter Conductor range: up to 4 x 95mm2 LVABC Ideal for cutting bundled LVABC service and mains cables. Not suitable for high tensile steel.

Cable strippers Specially designed to strip LVABC

Product Number Cable Size (mm²)

CS095 95

CS150 150

Product No: VS-MS47VH Non contact audible, visual, vibrating voltage tester 70-600 Vac Microwave leakage detection > 5mW/cm Includes 4 LR44 batteries

E2 0107

Product No: TOOL BAG Linesman’s plastic tool bag Product No: TBLVABC Linesman’s LVABC tool kit. Includes tool bag, RPS13/17-6H, PPI514, CIE100, PMR87 (4) TOOL BAG

Product No: CES1 & CES2 Cable end seals. Easy push on cap providing complete waterproofing of cable ends. Only two sizes required to cover entire range of LVABC cables.

Product Number

Cable Size

(mm²)

Diameter of cable (mm)

Length L (mm)

CES1 16 to 70 7.5 to 13.5 45

CES2 95 to 150 16.5 to 21.0 45

Pack Size

50

50

TBLVABC


Product No: 12870 Service Cable Come-along Conductor range: 2 x 16mm2 to 4 x 35mm2 Conductor Type: LVABC Max working load: 2kN Failing Load: 12.5kN Weight: 0.9kg

Product No: 12887 Service/Mains Cable Come-along Conductor range: 2* x 25mm2 to 4 x 95mm2 Conductor Type: LVABC Max working load: 10kN Weight: 2.1kg *additional sleeving may be required for some 2 core cables

Product No: SCBT38 Mains cable come-along Conductor range: 4 x 95mm2 Conductor type: LVABC Max working load: 8kN Failing Load: 25kN Weight: 3.8kg

Product No: BCCA-495150-3 Mains cable come-along Conductor range: 4x95mm2 to 4 x 150mm2 Conductor type: Bundled LVABC Max working load: Failing Load: Weight: 6.3kg

Product No: MR5341 Mains cable come-along Conductor range: 4 x 95mm2 Conductor type: LVABC Max working load: 20kN Failing Load: 32kN Weight: 5.0kg

Product No: 5340 Mains cable come-along Conductor range: 4 x 25mm2 to 4 x 50mm2 Conductor type: LVABC Max working load: 20kN Failing Load: 35kN Weight: 5.0kg

Product No: 1685-31 Mains cable come-along Conductor range: 2 x 25mm2 to 2 x 95mm2 Conductor type: LVABC Max working load: 29kN Failing Load: 46kN Weight: 2.3kg

TOOLS AND ACCESSORIES Stringing Tools

E3 0107


Product No: GRIP Service line tensioner Max working load: 1kN Failing Load: 5kN Weight: 1.4kg Ideal for hand stringing overhead service conductors and other light pulling work. Use in conjunction with come-along product number 12870.

Product No: BR50-S Ratchet buckle and strap Safe working load: 21.6kN

Product No: 6707BC Cable stringing block Working load: 1134kg Weight: 4.5kg Sheave diameter: 178mm Groove diameter: 53mm Groove depth: 30mm For complete specifications and accessories, please call Sicame.

E4 0107

TOOLS AND ACCESSORIES Stringing Tools

Product No: TOOL-LUG-ALL 30A-1300 • 1360kg max capacity • Step reverse feature • Complete with bag • Light weight: 4.5kg

Product No: PST Service tensioner


CABLE JOINTING TOOLS JTN Tools E5

0107

Product Number Overall Length (mm) Weight (g)

JTN/2 160 52

Insulated Core Wedge Designed to aid the separation of cores during jointing, these wedges are moulded in Nylon to resist detrimental wear at the tip during normal use. The thumb-and-finger grip assists insertion and removal, but it’s small enough not to obstruct work on and around the joint.

Insulated Core Separator & Wedge Ideal for 3 core sector cables when a standard wedge cannot be employed.

Product Number Overall Length (mm) Weight (g)

JTN/3 262 87

Product Number Overall length (mm)

Depth of blade (mm) Weight (g)

JTN/4 245 39 90

“Hepnyf” Plastic Hack-Knife Developed for stripping the lead sheath and removal of the bedding compound from cable. A clean cut can be made without damage to the underlying insulation, allowing the sheath of live cables to be safely removed. The blade can be re-sharpened with a file.

Product Number: RIPPER - cable sheath remover The all metal, multi-grip handle can be gripped outside or inside, right & left hand. Cuts most plastic insulation cold. Apply heat and the toughest hardest plastic cuts like butter. Cuts any shape any direction, no limit to diameter or length. Blade can be sharpened or replaced. Replacement blades available.

Product Number: ORB-1 - Oxide removal brush Painted black (for identification) for use on copper conductors to remove copper oxide film prior to crimping of cable lugs. Product Number: ORB-2 - Oxide removal brush Painted white (for identification) for use on aluminium conductors to remove aluminium oxide film prior to crimping of cable lugs. This is a safe and efficient method for removing oxide film from conductors


Product No: SB-3UK battery powered impact socket driver Battery powered tool especially designed for use with shear head type bolts. Suitable for use on all Sicame products fitted with shear head bolts. The SB-3UK package contains: Battery powered impact driver (1) Nickel-metal hydride re-chargeable battery (1) Mains (240V) powered battery charger (1) 13mm AF, six sided 1/2 inch drive socket (1) 17mm AF, six sided 1/2 inch drive socket (1) Sturdy plastic carrying case and operating instructions Impact Driver Specifications: Torque: 196 Nm Speed: 0-2,200 rpm Motor: 14.4 Vdc Socket drive: 1/2” square Dimensions: 350 (L) x 180 (H) x 75 (W) mm Weight: 2.5 kg (including battery) Battery Specifications: Output: 14.4 Vdc Capacity: 3 Amp Hour Life: 3000 charges (approx) Charge time: 40 mins with supplied charger Charger Specifications: Input voltage: 240V Capacity: 230VA Equipped with various status indicating LED’s Features: ∗ Fully insulated tool rated to 1000V ac, 1500 Vdc ∗ Unique shape to reduce its length for easy access in tight spaces. ∗ Variable speed ∗ Well balanced and lightweight ∗ Accepts any E-Robo series 14.4V battery

Impact driver

Re-chargeable battery

240 V battery charger

Also available as an optional extra: 12Vdc powered battery charger for

use in motor vehicles. Contact Sicame for details.

Any other battery or powered driver must be referred to Sicame Australia for evaluation and approval prior to use on Sicame products.

E6 0107

TOOLS AND ACCESSORIES Battery Powered Driver


PA5D

Product Number Cable Type

Cable Diameter

(mm)

No. and Size of Cores

(mm²)

Min. Failing Load (kN)

PC63R22 Neutral Screened 14 to 22 2.5

PC63F27 Twisted or Flat 2 x 6 to 4 x 35 2.5

PC63F27A Twisted or Flat 2 x 6 to 4 x 35 2.5

PA4 Twisted or Flat 2 x 16 to 2 x 25 6

PA5 Twisted or Flat 2 x 25 to 2 x 50 14

PA5D Twisted or Flat 2 x 16 to 4 x 25 12

PC63F27B Twisted or Flat 2 x 6 to 4 x 35 2.5

Pack Size

10

100

100

100

10

10

10

PA & PC SERIES Wedge type strain clamps ∗ PA series for higher tensions. ∗ PC series for service tensions. ∗ PC series suitable for 2, 3 and 4 core

twisted cables. ∗ Stainless steel bails on PA and PC

models. ∗ Fibreglass reinforced UV stabilised nylon. ∗ Stainless steel bails ∗ Fibreglass reinforced UV stabilised nylon.

Product Num-ber

Cable Size (mm²) Strap Hook Style

BCST-2025-3G 2 x 10 to 35 Galvanised Open

BCST-4035-3G 4 x 10 to 35 Galvanised Open

BCST-2025-3P 2 x 10 to 35 Nylon Open

BCST-2025-3PA 2 x 10 to 35 Nylon Closed

BCST-4035-3P 4 x 10 to 35 Nylon Open

BCST-4035-3PA 4 x 10 to 35 Nylon Closed

Pack Size

50

30

50

50

30

30

BCST Series Bolted Type Service Strain Clamps ∗ Nylon glass reinforced clamping blocks ∗ Blocks spring loaded for ease of cable

mounting ∗ Galvanised steel or plastic strap ∗ M10 stainless steel fastening hardware ∗ Can also be used as a suspension fitting by

rotating the clamping blocks 90 degrees

BCST-2025-3G BCST-4035-3G BCST-2025-3P BCST-2025-3PA BCST-4035-3P BCST-4035-3PA

PC63F27B

F1 0107

MECHANICAL FITTINGS PA, PC AND BCST Series

PC63F27 PC63F27A

PA5 PC63R22 PA4


Product Number

Dia. of circum-scribing circle over laid-up cable cores

(mm)

Cable Size (mm²)

2 Core 3 Core 4 Core

SC435 22 to 27 50 35, 50 25, 35

SC450 27 to 30 50

SC470 31 to 33 95 70

SC495 37 to 40 95

SC4150 43 to 47 150

Pack Size

20

20

20

20

20

Suspension clamps and termination clamps for ABC mains and sub-mains.

Product Number Cable Size (mm²) Maximum Fail-

ing Load (kN)

Rated Everyday Tension

(kN)

PA10/1 2 x 25 to 50 and 4 x 25 to 50 37 6

PA10/1S* 2 x 25 to 50 and 4 x 25 to 50 37 6

PA11/1 2 x 50 to 95 and 4 x 50 to 95 43 6

PA11/1S* 2 x 50 to 95 and 4 x 50 to 95 43 6

PA122A 4 x 95 to 4 x 150 72

*Stainless steel fasteners

Pack Size

6

6

6

6

15

PA2535 2 x 25 and 4 x 25 to 35 25

SC SERIES SUSPENSION CLAMPS Application: Suspension of LVABC from 25mm2 to 150mm2 Features: * Suitable for angles up to 30º * 30º to 60º use PSY/H bracket * Hinged aluminium alloy with body with stainless

steel fasteners * Reinforced hanging eye to stop wear through

vibration * Large angle yokes available SC495

PA SERIES TERMINATION CLAMPS Application: Termination of LVABC 2 x 25mm2 to 4 x 150mm2 Features: * Bolted full tension clamp * Stainless steel fasteners available as

an option * Meets requirements of AS3560 * Removable clevis pin Application Note: Use fillers if only 2 cores are utilised.

F2 0107

MECHANICAL FITTINGS SC and PA Series

PSY/H

158mm

PA122A

PA2535


OPEN EYE BOLTS TO AS3766

Length (L) mm

Product Number

16mm Dia. (D) 20mm Dia. (D)

200 - OEB20X200

250 OEB16X250 * OEB20X250 *

300 - OEB20X300

325 OEB16X325

350 OEB16X350 * OEB20X350 *

450 OEB16X450 * -

* Preferred item in AS3766

Pack Size

15

15

15

15

15

15

Product No: J HOOK Size: M12 to AS3766 Packed in bags of 50

Product No: J HOOK-T J Hook with earth tag Size: M12 to AS3766 Packed in bags of 50

Product No: Q HOOK Size: M12 to AS 3766 Packed in bags of 50

Product No: HB1 Galvanised steel hook bracket. Max working load: 12kN Hook diameter: 16mm To AS3766

L

Thread Length

150mm

Product No: ANG BKT

To Energy Australia specifications

200 m

m

HARDWARE OEB, JH and QH Series

G1 0107

J HOOK

J HOOK-T

Q HOOK


Product No: OEN M12 M12 eye nut to Energy Australia specifications

Product No: OEN M12 E M12 extended eye nut to Energy Australia specifications

Product No: LFG150 1.5kN weak link to Energy Australia specifications Packed in bags of 100

HARDWARE Weak links and eye nuts

G2 0107

ABC Mechanical Weak Link Can be installed between suspension clamp and pole support fitting. Can also be installed between service cable strain clamps or mains cable strain clamps. Mild steel galvanized to AS1650.

Product Number Colour coded

Dimensions

D (mm) L (mm) M (mm)

LFG400T 4 10 65 20

LFG600T 6 10 65 20

LFG800T 8 10 65 20

Nominal Failing Load (kN)

OEN M12

OEN M12 E

LFG150

LFG800T


Locking -Type Photocontrols and Delayed Response Thermal Series Built-in time delay prevents false cycling caused by lightning flashes or stray headlights. Specifications Housing: UV stabilized high-impact polypropylene. Photocell: 1 inch cadmium sulphide light sensitive element. Turn-on: 1 to 3 foot-candles (10 to 30 Lux) Turn-on/Turn-off Ratio: 1:3. Time Delay: Minimum 15 seconds. Switch Type: Single-pole, single-throw. Contact position at night normally closed. Temperature Range: -40° to 170° F. Power Consumption: 1.1 watts average at 120 VAC. Rated Life: 5,000 operations minimum at rated load. All products CSA Certified. Optional Surge Protection: • Open Type (modified expulsion) 2.5 KV spark over minimum with

5,000 amps follow through. Add suffix “LA”. • Enclosed Type (expulsion) 2.0 KV spark over minimum with

10,000 amps follow through. Add suffix “ELA”. • MOV (Metal Oxide Varistor). 90 joule rating. Add suffix “MOV”

Dimensions: 3.07” diameter, 2.15” high.

Product Number Specifications

Voltage Rating Surge Protection Lux rating

P68275LA/20 208-277 1800VA Open type 20

P68275LA/30 208-277 1800VA Open Type 30

P68275MOV/20 208-277 1800VA Metal oxide varistor 20

P2275-2 120 1800VA None

Accessories

M2AF Receptacle for the above photocontrol units

JP275 Low profile cover for receptacle. Shorts line to load, keeps lights ON at all times unless turned off from remote location.

Other models and accessories are available. Contact Sicame for details.

M2AF

JP275

TIME AND LIGHT CONTROLS H1 0107


Personal SafetyPersonal Safety Safety Glasses Stylish safety glasses made from tough polycar-bonate, offering 98% UV protection. Adjustable sides. Delivered with pouch. Clear and tinted models available.

Face Shield Protect yourself from short circuit arcs when working on switchboards; • No metallic parts • Adjustable • Colourless 1.5mm anti-condensation, polycar-

bonate face shield • Two models available, with Brow shield &

Clip-on to hardhat.

Safety Over-glasses Safety glasses made from tough polycar-bonate, offering 98% UV protection. Ad-justable sides. Delivered with pouch. Clear and tinted models available. MO-11010 MO-11011

MO-186 MO-184 Helmet not included

J1 0107


MO-11000 Clear lenses, delivered in pouch

MO-11001 Tinted lenses, delivered in pouch


MO-11010 Clear lenses

MO-11011 Tinted lenses


MO-184 Clip onto helmet

MO-186 Brow Shield


MS-121 Delivered with batteries & carry bag Weight: 0.09 Kg

M-95-864 Hooks set for helmet

LED Headlamp Can be worn either on the head or any kind of helmet. • Lighting by 3 high performance LED’s. • 3 lighting levels. • Adjustable lamp height angle. • Very light, waterproof IP65. • Range: 10 to 15 metres. • Powered by 3 batteries LR03 (AAA). • Battery life: 80 hours approx.

MO-11000

MO-11001


Personal SafetyPersonal Safety J2 0107


CG-98-A 8

CG-98-B 9

CG-98-C 10

CG-98-D 11


CG-99-A 8

CG-99-B 9

CG-99-C 10

CG-99-D 11

Leather Overgloves • Used as outer glove. • Silicon grain leather, very supple. • Large protective cuff in chrome tanned hide. • Velcro strap.


CG-80-H Men

CG-80-F Women

Cotton under-gloves • To be used under insulating rubber gloves

1000V Insulating Gloves—Single Colour • Tested to IEC-60903 Category M, Class 0 • Made from 1mm thick specially treated latex • Weight: 200g • Available in 4 sizes • Individually tested and shipped in a sealed plastic

bag marked with test date


CG-10-A Size 8

CG-10-B Size 9

CG-10-C Size 10

CG-10-D Size 11

Leather Overgloves • Used as outer glove. • Silicon grain leather, very supple. • Large protective cuff in chrome tanned hide. • Velcro strap. • Designed for use with >1000V insulating gloves


Personal SafetyPersonal Safety J3 0107

Bags for insulating mats • Especially designed for carrying and protecting

insulating mats. • Equipped with a shoulder strap and a plastic win-

dow for instructions and storage identification.

Product Number Thickness (mm) Class

MP-42/11 3 3

MP-42/16 3 3

Voltage (kV)

≤ 26.5

≤ 26.5

Dimensions

1 x 1

0.6 x 1

Insulating mats • The matting is manufactured of elastomer compounds

with slip-resistant surface. • High quality dielectrical rubber. • Tested to IEC-61111.

Carry bag • Made from reinforced waterproof fabric for

transport of rubber gloves in vehicles and tool boxes.

• Rear loop for belt and snaps.

Product Number Overall length (mm) Weight (g)

CG-36 60 x 180 x 400 0.120

Product Number Description Length (cm)

MP-01 For MP-42/16 and MP-42/66 70

MP-02 For MP-42/11 110

Rubber gloves storage box with window • To be placed in high voltage sub-stations. • Insulating material, shock resistant, yellow colour. • Transparent window (ability to check gloves presence). • Bottle of talc included. • Attachment: 4 holes 3.5mm dia., centre distances

155x345mm. • U.V. protective window.


CG-35/1 60 x 210 x 460 0.730


IEC 60900 requires that all tools comply with various dimensional stan-dards, to ensure that the tools meet important ergonomic design principles

and are safe and easy to use. (Clause 5.3) DIMENSIONS

The dielectric test proves the integrity and performance of the tool’s insulation. After conditioning in a water bath or wet cham-ber for 24 hrs, 10kV is applied for 3 minutes to the tool whilst it is immersed. The leakage current is measured and checked for

compliance, the value of which depends on the type and size of tool. (Clause 5.5)

DIELECTRIC STRENGTH

An indentation test is carried out to ensure the tool’s insulating properties are retained after being subjected to a point impact. After the impact, the insulation must withstand 5kV for 3 minutes without puncture, sparkover

or flashover. (Clause 5.6)

INDENTATION

The adhesion test ensures that the tool’s insulating coat will not slip, move or separate from the metal parts of the tool. After conditioning at 70 deg C for 168 hours, the tool is allowed to cool to an ambient temperature, then various forces are applied to test the adhesion properties and per-

formance. (Clause 5.7)

ADHESION

Each type of tool is subjected to mechanical tests to ensure com-pliance with various ISO or national standards and to ensure

the tool has the necessary mechanical strength for its intended application.

MECHANICAL

Orange, flame retardant PVC insulating outer layer with anti-slip treatment.

Finger guard bonded to tool as part of the inner insulation layer

Tough, impact resistant, white inner insulating layer, bonded to metal

Primary adhesive layer

IEC 60900 TESTED 1000V IEC 60900 TESTED 1000V INSULATED TOOLSINSULATED TOOLS

J4 0107

Each type of tool is subjected to an impact test to ensure the insulation can with-stand normal daily wear and tear without serious damage. Impact tests are car-

ried out at ambient, low and extremely low temperatures. (Clause 5.4) IMPACT


1000V Insulated Tools1000V Insulated Tools J5 0107

Product Number Description Weight (g)

MO-65222 Flat blade 4 x 85mm 65

Insulated phase tester screwdriver • Phase detection from 127V. • Maximum voltage 1000V. • Signalling by intermittent lighting through ultra

high intensity diode. • Works with an un-removable lithium battery. • 3 year battery life

Flat blade screwdrivers • Chrome - molybdenum vanadium steel blade


MO-65203 3mm blade x 100mm 33

MO-65204 3.5mm blade x 100mm 37


MO-65206 5.5mm blade x 125mm 75

MO-65207 6.5mm blade x 150mm 94


MO-65211 10mm blade x 200mm 195

Pozidriv screwdrivers • Chrome - molybdenum vanadium steel blade


MO-65240 3mm No 0 head x 60mm 25

MO-65242 4.5mm No 1 head x 80mm 50

MO-65244 6mm No 2 head x 100mm 75

MO-65246 8mm No 3 head x 150mm 150

MO-65248 10mm No 4 head x 200mm 230

Phillips screwdrivers • Chrome - molybdenum vanadium steel blade


MO-65230 3mm No 0 head x 60mm 25

MO-65232 4.5mm No 1 head x 80mm 50

MO-65234 6mm No 2 head x 100mm 75

MO-65236 8mm No 3 head x 150mm 150

MO-65238 10mm No 4 head x 200mm 230



Universal pliers • Special tool steel, oil hardened. • Burnished head

Flat nose pliers • Special tool steel, oil hardened. • Burnished head


MO-66300 145 115

MO-66302 160 160


MO-66001 160 210

MO-66002 180 260

MO-66003 200 300

MO-66005* 250 510

* For steel armoured cable


MO-66202 160 150 Round nose pliers • Special tool steel, oil hardened. • Burnished head


MO-66402 160 160

MO-66404 200 185

Bent snipe nose pliers • Chrome-vanadium steel. • Burnished head




MO-66102 160 145 Long nose pliers with side cutter • Special tool steel, oil hardened. • Burnished head


MO-66105 200 200

Plug pliers for pre-insulated pin terminals • Chrome-vanadium steel for 2.8, 5 , 6.35mm pin

terminals.


MO-66502 250 410

Waterpump pliers • Chrome-vanadium steel. • Burnished head


MO-66505 250 405

Box joint pliers

Product Number Overall length (mm) Cutting capacity (mm)

Soft 80Kg/mm2 Hard 140Kg/ mm2

MO-67101 140 Ø 2 Ø 1 150

MO-67102 160 Ø 2.5 Ø 1.5 180

MO-67103 180 Ø 3 Ø 2.5 210

Weight (g) Side cutters • Special carbon steel. • Oil hardened. • Burnished head.

Standard type



Product Number Overall length (mm) Weight (g) Soft 80Kg/mm2 Hard 140Kg/mm2

MO-67401 140 Ø 1 Ø 2 165

MO-67402 160 Ø 2 Ø 3 210

MO-67404 200 Ø 3 Ø 4 450

Cutting capacity (mm) End cutting pliers

• Special carbon steel. • Oil hardened. • Burnished head.

Product Number Overall length (mm) Cutting capacity (mm) Weight (g)

MO-67500 170 Maximum Ø 4 420

Cable cutter • Chrome-vanadium. • Forged steel.

Product Number Cutting capacity (max) Weight (g)

MO-67599 Ø 32mm/ 180mm2 Cu 250mm2 Al 900

MO-67600 Ø 38mm/ 240mm2 Cu 300mm2 Al 950

MO-67601 Ø 55mm/ 300mm2 Cu 450mm2 Al 975

Ratchet cable cutters • For copper and aluminium cables only. • Treated forged steel blade.

MO-67601 MO-67599

MO-67501 MO-67502

Product Number Overall length (mm) Cutting capacity (mm) Weight (g)

MO-67501 170 Maximum Ø 15 285

MO-67502 230 Maximum Ø 20 520

Cable cutters • Chrome-vanadium. • Forged steel. • Oil-hardened.

MO-67401, MO-67402 MO-67404


Product Number Cutting capacity Weight (g)

MO-67611 Ø 24mm/ 150mm2 Cu 180mm2 Al 790


Parrot beak style cable cutter • For copper and aluminium only. • Treated forged steel blade.

Hacksaw • Protected hard forged steel. • Two blade positions. • Flushed and 90º cutting angle. • Delivered with 2 blades.

Product Number Blade length (mm) Overall length (mm) Weight (g)

MO-64502 300 450 780

Stripping pliers for L.V. cables • Aluminium casting plier. • To strip L.V. twisted cables. • Blade depth adjustable. • For use on LVABC cable.

Product Number Overall length (mm) Stripping capacity Weight (g)

MO-67304 220 from 16 to 150mm2 470

Stripping pliers for L.V. cables • Aluminium casting plier. • To strip L.V. cables. • Blade depth adjustable. • For use on LVABC cable.

Product Number Overall length (mm) Stripping capacity (mm2) Weight (g)

MO-67305 265 From 16 to 150 650

MO-67306 270 From 50 to 240 670



Product Number Overall length (mm) Capacity (mm2) Weight (g)

MO-67302 160 0.6 to 10 170

Wire stripping pliers • Chrome vanadium. • Burnished head.

Stripping knifes • Delivered with pouch.

Product Number Blade length (mm) Overall length (mm) Weight (g)

MO-61001 62 (Straight) 190 110

MO-61002 50 (Curve) 190 110

Adjustable spanner • Special tool steel. • Oil hardened.

Product Number Overall length (mm) Maximum capacity (mm) Weight (g)

MO-69002 210 24 295

MO-69003 250 28 450

MO-69004 310 34 550

MO-69005 385 43 1350



Product Number AF (mm) Weight (g)

MO-69210 10 160

MO-69213 13 190

MO-69216 16 350

MO-69217 17 370

MO-69218 18 380

MO-69219 19 390

Reversible hexagonal ratchet handle • Special tool steel. • Oil hardened.

Combination wrench • Special steel sockets. Product Number

4 hexagonal sockets

AF Sizes (mm) Length (mm)

MO-68702 8-10-12-14 150x150mm 260

MO-68703 7-9-11-13 150x150mm 250

MO-68704 8-10-13-17 150x150mm 260

Weight (g)

Right angle hexagonal key wrench • Chrome-vanadium steel. Product Number

Hexagonal head (mm)

AF A B

MO-69903 3 83 123 30

MO-69904 4 84 124 40

MO-69905 5 84 126 50

MO-69906 6 86 126 70

MO-69908 8 87 128 110

MO-69910 10 87 130 150

MO-69912 12 90 132 240

Weight (g)

A

B




MO-68008 8 40

MO-68009 9 40

MO-68010 10 45

MO-68011 11 50

MO-68012 12 60

MO-68013 13 80

MO-68014 14 100

MO-68015 15 110

MO-68016 16 120

MO-68017 17 140

MO-68018 18 160

MO-68019 19 170

Open end spanners. • Chrome-vanadium steel.


MO-68020 20 185

MO-68021 21 200

MO-68022 22 220

MO-68023 23 250

MO-68024 24 260

MO-68025 25 280

MO-68026 26 300

MO-68027 27 340

MO-68028 28 360

MO-68029 29 400

MO-68030 30 500

MO-68032 32 570


MO-68008/19 Open end spanner set including 8, 10, 11, 12, 13, 14, 17, 19mm AF spanners 685

Spanner Sets

Cranked ring wrench • Chrome-vanadium steel.


MO-68107 7 35

MO-68108 8 40

MO-68109 9 45

MO-68110 10 50

MO-68111 11 65

MO-68112 12 80

MO-68113 13 100

MO-68114 14 120

MO-68115 15 150

MO-68116 16 180

MO-68117 17 190

MO-68118 18 195

MO-68119 19 200


MO-68120 20 240

MO-68121 21 260

MO-68122 22 260

MO-68123 23 270

MO-68124 24 280

MO-68125 25 300

MO-68126 26 360

MO-68127 27 400

MO-68128 28 440

MO-68129 29 480

MO-68130 30 500

MO-68132 32 540




MO-68610 10 145

MO-68613 13 185

MO-68614 14 220

Hexagonal spanner with T handle • Chrome steel. • Length 130mm


MO-69813 Socket 13mm AF - 1/4” drive 45

MO-69317 Socket 17mm AF - 3/8” drive 60

MO-69840 Extension 1/4” AF x 3/8” drive 60

MO-69512 Reversible ratchet - 1/4” drive 200

MO-69813/ 17 Complete socket set in plastic box 230 x 170 x 45 365


MO-69810 Socket 10mm - 1/4” 35

MO-69813 Socket 13mm - 1/4” 45

MO-69317 Socket 17mm - 3/8” 60

MO-69840 Extension 1/4” - 3/8” 60

MO-69512 Reversible ratchet - 1/4” 200

MO-69810/17 Complete socket set in plastic box 230 x 170 x 45 500

1/4” sockets wrench sets • Chrome steel.

MO-69840/17

Insulated Tool Kits • For most common operations


MO-65242 - Pozidriv screwdriver* No 1 4.5 x 80mm

MO-65244 - Pozidriv screwdriver* No 2 6 x 100mm

MO-65204 - Flat blade screwdriver 3.5 x 100mm

MO-65206 - Flat blade screwdriver 5.5 x 125mm

MO-65209 - Flat blade screwdriver 8 x 175mm

KIT 03



Sockets 1/2” drive - 12 sided Sockets 3/8” drive - 6 sided

3/8” & 1/2” drive sockets, sets and accessories • Chrome steel.

MO-69308/23 MO-69543


MO-69306 6mm AF socket 25


MO-69308* 8mm AF socket 30















MO-69513* Reversible ratchet 600

MO-69523* 130mm extension 124

MO-69533 250mm extension 270

MO-69542 130mm T wrench 220


MO-69308/ 23 Socket set comprising items marked * in plas-tic box 410 x 120 x 75

1250

* Sockets composing the sets



















MO-69514* Reversible ratchet 600

MO-69524* 125mm extension 250



MO-69408/ 23 Socket set comprising

items marked * in plastic box 410 x 120 x 75

1500

* Sockets composing the sets

MO-69524




MO-69610 10 75

MO-69613 13 80

MO-69614 14 100

MO-69616 16 115

MO-69617 17 125

MO-69618 18 140

MO-69619 19 160

MO-69621 21 190

Long series sockets, 3/8” drive • Chrome steel. • 65mm length


MO-69735 3/8” 25

MO-69736 7/16” 30

MO-69737 1/2” 35

MO-69738 9/16” 35

MO-69739 5/8” 42

MO-69740 11/16” 50

MO-69741 3/4” 55

MO-69742 13/16” 60

6 sided male hex key socket, 3/8” drive • Tool steel.


MO-69393 3 45

MO-69394 4 55

MO-69395 5 60

MO-69396 6 65

MO-69397 7 70

MO-69398 8 70


MO-69050 8 to 54 Nm 790

Insulated torque wrench, 3/8” drive • Capacity: 8 to 54 Nm (ibF Ft: 5-40). • Length: 325mm • Tolerance: 4%

U.S Standard sockets, 3/8” drive • Chrome steel.



Contractors 1000V Insulated Tool Kit Product No: TKC - 1000V -1

Complete equipment requirements for level 2 service providers Tool bag included Tool kit comprises of the following items


Personnel Equipment

MO-11001 1 pair safety glasses

CG-98-* 1 pair working gloves

CG-80-H 1 pair cotton under-gloves

Insulating Gloves & Accessories

CG-10-* 1 pair 1000v insulated gloves

CG-36 1 carry bag for insulated gloves

Insulated tools

MO-61001 1 stripping knife (curved blade)

MO-65203 1 flat blade screwdriver 3x100mm

MO-65206 1 flat blade screwdriver 5.5x125mm

MO-65209 1 flat blade screwdriver 8x175mm

MO-65222 1 phase tester screwdriver 4x85mm

MO-65230 1 Phillips screwdriver N0 0



MO-66003 1 universal pliers 200mm

MO-66102 1 long nose pliers 160mm

MO-67103 1 side cutter 180mm

MO-68013 1 open ended spanner 13mm


Tools Continue Product Number Description


MO-68113 1 ring spanner 13mm



MO-69003 Adjustable wrench

MO-69413 1 1/2” drive-12 sided socket 13mm



MO-69514 1 1/2” reverse ratchet

MO-69524 1 1/2” 125mm Ext bar

* Gloves available in 4 sizes A=8, B=9, C=10 & D=11

Contractors Tool bag Product No: M-87370

For intervention works Strong waterproof, canvas reinforced bottom Large capacity of storage with shoulder strap


EARTH SYSTEMS Accessories

K1 0107

Drop-Out Fuse Earthing Adaptor Used for providing an earthing point on the bottom of drop out fuse carriers where conductors from drop out fuses to transformers are fully insulated.


LKA/C “C” - Hexagon fitting

LKA/K “K” - Universal fitting

LKA/S “S” - Shotgun fitting


CRA-C “C” - Hexagon fitting

CRA-K “K” - Universal fitting

CRA-S “S” - Shotgun fitting


MT-630-C “C” - Hexagon fitting

MT-630-K “K” - Universal fitting

MT-630-S “S” - Shotgun fitting

Fuse Remover Adaptor Used to remove drop-out fuses Available in 2 different fittings

MT-630-K

LKA/C

LKA/K


FRA-C “C” - Hexagon fitting

FRA-K “K” - Universal fitting

FRA-K

CRA/S

Clamp Removal Arm (Pigtail) Used for removing MT-613/3 snap-on clamps from overhead lines Available in 3 different fittings Normally sold with MT-630 clamp application platform (refer below)

CRA/C CRA/K

Clamp Application Platform Used for attaching MT-613/3 snap-on clamps onto overhead lines. Available in 3 different fittings Normally sold with CRA clamp removal arm (Pigtail). (see above)

MT-630-C

FRA-C

Product Number

DOFEA

Product No: DOFEA

LKA/S

Link adaptor Used for attaching and removing drop-out fuses prior to applying a DOFEA. Available in 3 different fittings


MDS/2


MOD-C “C” - Hexagon fitting

MOD-K “K” - Universal fitting

MOD-S “S” - Shotgun fitting

MOD-E “E” - Bayonet fitting

MOD/E


SFP-C “C” - Hexagon fitting

SFP-K “K” - Universal fitting


K2 0107


MDS/2 Mines Discharge Stick with Standard with 2 m lead Handle length: 1 m

MDS/2 EXT Mines Discharge Stick with Standard with 2 m lead & extended nipple Handle length: 1 m

MDS/3 Mines Discharge Stick with Standard 3 m lead Handle length: 1 m

Modiwark Adaptor Used for holding Modiwark type voltage detectors on the end of a high voltage stick. Available in 4 different fittings


LLCR-C “C” - Hexagon fitting

LLCR-K “K” - Universal fitting

LLCR-S “S” - Shotgun fitting

Mines Discharge Sticks Used to discharge underground cables prior to being earthed.

MOD/C MOD/K MOD/S

LLCR/C LLCR/S

SFP/C

SFP/K

MDS/2 Ext

LLCR/K

Live Line Clamp Remover Fits onto a high voltage stick and is used for removing live line clamps. Available in 3 different fittings

Service Fuse Puller Used for pulling services fuses on poles/houses. Available in 2 different fittings



CM-02-C “C” - Hexagon fitting

CM-02-K “K” - Universal fitting


K3 0107

Product Number Diameter (mm)

Stub Diameter (mm)

M12/22 BRS STUB 12mm 22mm




Rating (kA)

25kA/0.5 secs

25kA/0.5 secs

45kA/0.5 secs

45kA/0.5 secs M12/22 BRS STUB

Fixed Earth Connection Point An earthing point used in substations & switchrooms. Includes Bolts & Washers. Two diameters are available - 22mm and 25mm

Voltage Detector Extension Probe Extension probe which fits voltage detector type CC-875 for testing insulated switchgear.

CM-02-C

Manoeuvering Hook Bronze-Copper nickel aluminium Weight : 0.120Kg Available in two different fittings


PROBE KSA/875 Length - 440mm Diameter - 20mm


POLE SAFETY STEPS Safety pole steps with washer

Product No: PROBE KSA/875

Product No: POLE SAFETY STEPS


CASE EX LGE Inside Dim 485x355x186mm

CASE LGE Inside Dim 395x320x117mm

CASE MED Inside Dim 300x220x90mm

Equipment Boxes Ideal for storage & transport of high voltage detectors, accessories & other instruments. Watertight, shock & vibration proof and also dust proof Complete with foam inserts



K4 0107

Connection adaptors for insulating sticks

CI-6-C

Hexagonal

C A or B

“MAJOR” Serie CM-4/ CM-6/ CM-7

E

Bayonet

S

Clamp - Stick

K

Universal

Acce

ssor

ies K E C

Con

nect

ion

A

dapt

ors

CI-3-K CI-7-K CI-4-K CI-6-K CI-5-K CI-3-E CI-7-E CI-4-E

CI-6-C CI-3-C

CI-5-C CI-7-C

K S A B E C K E A B C K S A B

Stic

ks

CI-5-C

CI-5-K CI-7-C

With this range, any accessory can be attached to any stick by using connection adaptors. For other models, please consult us.

CI-4-E CI-7-E

CI-3-C

End Cap for CI-3-C

CI-6-K

CI-7-K

CI-4-K

CI-5-C


K5

0107

Stick Adaptor To connect Ergon sticks with hexagonal “C” fittings.


Clamp Application Handle Small PVC handle to apply Bayonet type earth clamps.

Stick Adaptor To connect Integral sticks to universal head tools or hexagonal “C” fittings. Available in 2 different fittings.


IATH-C “C” - Hexagon fitting Length - 150mm

IATH-K “K” - Universal fitting Length - 200mm

Stick Adaptor To connect SECV/C sticks with hexagonal “C” fittings.

P/N: IATH-K

P/N: IATH-C


HEC-250-E Length - 340mm


CAPALEC ADAPTOR Length - 210mm


SECV/C SECV to C adaptor Length - 230mm

Product No: HEC-250-E

Product No: CAPALEC ADAPTOR


Conductor Brushes Pivoting - 95 x 90 x 64mm Weight : 0.090Kg Universal head


MG-206-AK Moulded red colour body with card. Reserved for aluminium conductors

MG-206-CK Moulded red colour body with card. Reserved for copper conductors.

Conductor Brushes Pivoting - 110 x 110 x 70mm Weight : 0.250Kg


MG-352-K Moulded orange colour body with card. Reserved for aluminium conductors

MG-352-VK Moulded green colour body with card. Reserved for copper conductors.

MG-353-R Orange spare brush for MG-353-K. For hand brushing use.

MG-353-V Green spare brush for MG-353-K. For hand brushing use.

MG-354-K Round brush - Ø 58 x 100mm Weight: 0.250 Kg

MG-355 Spare brush for MG-354-K

Diameter Measuring Gauge Conductor range 3 to 16mm Ø. Entirely insulated material 270 x 35 x 12mm Weight: 0.090 Kg Rising Sun’ fitting Delivered in bag

K6 0107


Cleaning Brushes Hex fitting


MD-10-C Concave brush with two rows of perpendicular bristles 100 x 125 x 170mm - Weight: 0.500Kg

MD-12-C Round head brush Ø 175 x 228mm - Weight: 0.500Kg

MD-14-C Adjustable hinged round head brush Ø 175 x 328mm - Weight: 0.500Kg

MD-12-C

MD-10-C

MG-354-K

Product Number

MD-535-K

MD-14-C


K7

0107

Fixed Points Used for providing earthing points in substations/ switchrooms and flat conductors Commonly used with MT-1921-E earth clamps (refer to above)

Product Number

Sphere Dimension

Weight (g) Fixing

MT-3951 Ø 25mm 240 Thread: M12

MT-3952 Ø 25mm 240 Thread: M16

MT-3951/1 Ø 25mm 300 Bolt: M12 - L = 45mm

MT-3952/1 Ø 25mm 350 Bolt: M16 - L = 45mm

MT-3950/35* Ø 25mm 300 Bolt: M16 - L = 35mm

Rating (kA)

25kA/0.5 sec

45kA/0.5 sec

* = Not IEC

P/N: MT-3951 MT-3952 P/N:

MT-3950/35

P/N: MT-3951/1 MT-3952/1

Application Handle Used to tighten MT-815-S clamps onto earth connections.


MT-1921E H Earth Clamp with PVC Handle Length - 350mm

P/N: MT-1921E H

Hand Applied Earth Clamps For connection of MT-192-E clamps to fixed earthing points.

EARTH SYSTEMS Clamps


815S/H Handle Length - 320mm


Product Number Description BAG PVC ARB/454 Carry Bag 400 x 500 x 400 + Zipper

BAG PVC ARB/500 Carry Bag 500 x 500 x 150

BAG PVC ARB/501 Carry Bag 500 x 500 x 150 + 1 Divider






BAG PVC ARB/762 Carry Bag 700 x 600 x 200 + Zipper

Earth Set Carry Bags

Product Number Description BAG PVC ARB/MDS AES-MDS Stick Carry Bag

BAG PVC ARB/S110 1 x 1.0 Mt Stick Carry Bag
















BAG PVC ARB/520 5 x 2.0 Mt Stick Carry Bag

BAG Extra Pockets Extra Pockets /P or /A for Adaptors etc..

CARRY BAGS Earths Set & Stick Bags

K8 0107

ARB/S115

ARB/500

ARB/S415

Stick Carry Bags


LANYARDS & SANDBAGS K9

0107

Lanyard for MT-701/1 Clamps 8mm Megalon insulated Used for applying CATU clamp MT-701/1 onto over-head wires.

Product Number Length (Mt)

LANYARD 08M 8

LANYARD 09M 9

LANYARD 10M 10

LANYARD 11M 11

LANYARD 12M 12

LANYARD 13M 13

LANYARD 14M 14

LANYARD 15M 15

LANYARD 16M 16

LANYARD 17M 17

LANYARD 18M 18

LANYARD 19M 19

LANYARD 20M 20

LANYARD 21M 21

LANYARD 22M 22

LANYARD 23M 23

LANYARD 24M 24

LANYARD 25M 25

LANYARD 30M 30

LANYARD 35M 35

LANYARD 40M 40

LANYARD 45M 45

LANYARD 50M 50


SANDBAG ASSEMBLY Sandbag with link & sister clip

SANDBAG W/LOOP Bag with sand & carry loop

Sandbags Used with Megalon lanyards (see above) to hoist MT-701/1 clamps onto conductors.

P/N: SAND W/LOOP P/N: SANDBAG ASSEMBLY

Sister clip

Link

insulation piercing connectors low voltage insulated ... · pdf fileinsulation piercing...

Documents