investment project card - izvozno okno profiles fuera de cartera.pdf · investment project card ......

INVESTMENT PROJECT CARD

Project title: Integrated System of Urban Solid Waste

Cuban part: Business Group of the Iron and Steel Mechanical Industry (GESIME).

General description of the project: The proposed Urban Solid Waste Management Integrated System, comprises all the stages of the process, beginning by its correct selection, pick up, treatment, recycling and energetic assessment to generate electricity, heat and to produce organic fertilizer, sending to the sanitary landfills only approximately 17% of the non-assessable residues (textiles, hide, wood, others). The project will comprise the whole country, and it must be implemented by stages. It is intended to gradually reduce the total volume of generated waste that is sent today to dumps or sanitary landfills avoiding its negative impact upon the environment and human health, by means of an Urban Solid Waste Management Integrated System including all the stages of the process.

Investment modality: Joint Venture.

Proposition of contributions by the foreign part: Financing. Know how. Training of the Cuban technical force in new technologies. Specialized supplies of technological and industrial profile that complement and integrate the Cuban national industry.

Foreseen microlocalization: Located within a given zone in Havana, Cuba.

General market (demand): The recyclable residues obtained from secondary raw materials will be sent to the National Industry, and the surplus is expected to be exported. At present 16 families of products are processed and the main ones are: Steel junk, molten iron, stainless steel, copper, aluminum, bronze, lead, paper and cardboard paper, plastics, glass containers, glass, electronic junk. The generated gas is requested by the National Electric System for the generation of electric energy. The fertilizer could be fully used by the agricultural sector.

Proposed technology: Introduction of an advanced technology for the reusing, processing and recycling of waste enabling to lift and to stabilize the recovery levels and the revenues from the sales of secondary raw materials.

Contacts: Vice-President GESIME Telephone: (537) 263-3429 E-mail: [email protected]


Project title: Production and commercialization of long products of stainless steel and alloy steels.

Cuban part: Business Group of the Iron and Steel Mechanical Industry. (GESIME).

General description of the project: Creation of manufacturing capacities for long products of stainless steel and alloy steel, up to a nominal capacity of 180,000 tons per year, through the modernization and acquisition of equipment at the ACINOX Las Tunas steelworks company and the installation of a new rolling mill, in order to meet the domestic market demand and to promote exports.

Investment modality: Joint Venture

Proposition of contributions by the foreign part: Funding Know how. Technology transfer. Training of the Cuban technical force in the use of new technologies. Technological equipment. Foreign market.

Foreseen microlocalization: Empresa Aceros Inoxidables de Las Tunas (Stainless Steel Company of Las Tunas, trade name: ACINOX Las Tunas).

General market (demand): The production will be destined to cover the national demand and exports, anticipating that 97% of the production will be destined to the external market.

Proposed technology: The technology that was installed in the ACINOX Las Tunas company for the manufacture of stainless steel and special steels is based on a DUPLEX Process, which is made up of an electric arc furnace and a VOD (vacuum decarburization equipment) for the refinement of steel. Currently, the main producers of stainless and special steels use the TRIPLEX Process, which is made up of electric arc furnace, AOD (oxygen converter to remove large amounts of carbon) and VOD. This project proposes to replace the currently in use DUPLEX Process with the TRIPLEX Process: to add a new converter to the process. In addition, the project provides the assembly of a new rolling mill for long products, as well as the updating and modernization of the equipment currently in use.

Contacts: Vice-President GESIME Telephone: (537) 263-3429 E-mail: [email protected]


Project title: National Confinement Space for Hazardous Wastes.

Cuban part: Business Group of the Chemical Industry (GEIQ).

General description of the project: This project arises from the need to achieve a reduction in the environmental impact through the

confinement of chemical waste and expired chemicals and dangerous idle products, distributed

and stored in different entities throughout the national territory, which are generally stored in

improper conditions and which can affect the environment in general.

Currently there is an inventory of 11 products considered a priority for the studies at a first stage of

the technological project.

Products included in the technological study as part of the first stage:

• Dielectric fluids with PCB content.

• Small capacitors with PCB content.

• Residual solution containing arsenic.

• Technological equipment with arsenic content.

• Ceramic fillings contaminated with arsenic.

• Dangerous and idle hazardous chemicals containing lead, cyanides, vanadium, strontium,

cadmium, chromium, mercury and arsenic.

• Galvanic sludge.

• Lead tetraethyl.

• Waste with cyanides. (Insoluble cyanides).

• Vanadium. Vanadium pentoxide and other products with vanadium.

• Waste of mercury lamps.

Electronic scrap (does not include computers).

Investment modality: Funding for executing the project

Advance technology

Foreseen microlocalization: Chemical Enterprise of Cienfuegos (EQUIFA), Carretera Juraguá, Cienfuegos.

Proposed contributions by the foreign part: Funding.

Know how.

Training of the Cuban technical force in the use of new technologies.

Specialized technological and industrial supplies that complement and integrate the Cuban

national industry.

General market (demand): The project proposes to provide a specialized service of classification and analysis in the place of

origin of the wastes, their handling, transportation, storage and possible technological processes,

which make possible the recovery, recycling and possible export of some wastes.

Proposed technology: To be proposed by the foreign party.

Contacts: Vice-President GEIQ. Telephone: (53) 7 204 36 12.

E-mail: [email protected]


Project title: Construction and assembly of bioelectric power and biomass gasification plants.


General description of the project: It is presented as part of the program for the change of the energy matrix of the country, that projects the installation of 755 MW by means of 19 bioelectric plants in sugar mills, with greater parameters of pressure and temperature to operate for over 200 days yearly with sugarcane biomass and forestry biomass, mainly with marabou, available in the vicinity of these facilities. It intends to have a productive and financing alliance enabling the national industry to participate in the manufacture and the assembly of components, parts and pieces of the electricity production plants with biomass, such as boilers, metallic structures, containers, conducts, and electric systems. It foresees the modernization of the present productive capacities of manufacturing such components, particularly steam boilers.

Investment modality: Technological Alliance

Financing for investments

Contracts for the productive management

Proposed contributions by the foreign part: Funding

Know how.

Training of the Cuban technical force in the use of new technologies.

Specialized technological and industrial supplies that complement and integrate the Cuban

national industry.

Foreseen microlocalization: Boilers Factory Jesus Menéndez, Municipality of Sagua la Grande, Villa Clara, Cuba.

General market (demand):

19 Bioelectric plants to be installed in sugar mills

17 Forest Biomass Gasification Plants in Sawmills

Proposed technology: The project’s scope will be to achieve the modernization, repair, acquisition of new equipment and technologies for the design and manufacture of high pressure steam boilers. Includes machine tools, tooling, measuring instruments and computer tools for design and industrial modeling to boost the manufacture of boilers and other essentials of the bioelectric plants. • Boilers for the combustion of different types of biomass. • Fluidized bed combustion. Fluidized bed combustion system. • Burn in semi-suspension.

Contacts: Vice-President GESIME

Telephone: (53) 7 263 34 29

E-mail: [email protected]


Project title: Wind Farm Construction

Cuban part: Business Group of the Iron and Steel Mechanical Industry. (GESIME).)

General description of the project: To create modern technological and productive capacities that allow the national industry to participate in the construction of wind farms, taking into account the current potential found in Cuba regarding the production of metallic structures, wind generators, electrical and electronic components. A technological alliance will be established for the assembly of a wind tower production line with after sales services, which will replace imports during the assembly of the planned wind farms.

Investment modality: Joint Venture Medium and long-term funding to execute the investment.

Proposed contributions by the foreign part: Funding Know how. Training of the Cuban technical force in the use of new technologies. Specialized technological and industrial supplies that complement and integrate the Cuban national industry.

Foreseen microlocalization: Empresa de Transformado del Acero (Steel Transformation Company), Las Tunas, Cuba

General market (demand): It is planned to develop wind farms with an approximately total number of 300 towers.

Proposed technology: The factory must have a complete productive line for the manufacture of Wind Towers and the possibility of wind turbine assembly operations must be assessed.

Contacts: Vice-President GESIME Telephone: (53) 7 263 34 29 E-mail: [email protected]


Project title: Modernization and expansion of productive capacities in auto parts.


General description of the project: The AUTOPARTES Company is the only one in the country responsible for the production of automotive spare parts in several different lines such as: friction elements (blocks, brake pads and brake bands); discs and clutch linings; air, oil and fuel filters; flat joints, block cover joints and joint sets; radiators and seat linings. The project consists in expanding the production capacity to meet the current and future demand of the automotive industry, to make better use of existing technology and to replace others with up-to-date technology, which would allow the production to diversify, to increase productivity, to improve the quality standards, to humanize the work of the workshops and to be competitive with the products that the country currently imports. With the current technology a high level of rejection is generated, which with the acquisition of the new equipment will decrease to the internationally established levels. It is expected to increase production levels and quality in processes starting from the rehabilitation and modernization of technological equipment. This objective implies the work in the following aspects:

Replacement of imports of spare parts. Reduce production costs and energy carriers. Higher levels of automation. Maintain quality control by establishing an environmentally friendly process.

Investment modality: Funding for the investments. Joint Venture

Proposition of contributions by the foreign part: Funding Technology Know How Technological equipment Management methods Training of Cuban personnel.

Microlocalization: 62 Street % 99 y 101 #99015, Alberro, Cotorro, La Habana, Cuba.

General market (demand): The domestic market for spare parts would be of approximately USD 124 million.

Proposed technology: Advance technology for the modernization of the following lines:

Line of filters, Line of block cover joints, flat joints and joint sets, Line of brake blocks, Line of brake pads, Line of radiators and combs, Production line for oil, air and fuel filters, Clutch linings and cladding manufacturing line, Tooling workshop, Laboratory equipment. Sewing equipment.

Transport equipment.

Contacts: Vice-President GESIME Telephone: (53) 7 263 34 29. E-mail: [email protected]

mailto:[email protected]


Project title: Increase in the production capacity of candles and diversification of the products.

Cuban part: Business Group of the Light Industry (GEMPIL).

General description of the project: Currently the production of candles does not meet the national demand, reaching only a 25%. The project will allow replacing imports by expanding the diversity of products that prevent reaching all market segments. The project proposes to acquire and modernize the existing technology park with the acquisition of an extruder and 8 trowels for the current industry that manufactures these products. The project also proposes for a future stage the setting up of a candle production line in the eastern zone with 2 extrusion machines and 20 trowels, as well as the acquisition of machines for diversifying the products. The project is complemented in the national industry with the production of packaging and possibilities with the textile, chemical and perfume industries.

Investment modality: Technological alliances Financing to execute the project Another proposal for consideration by the foreign party

Proposition of contributions by the foreign part: Funding Know How Training of technical work force Specialized technology and component supplies

Foreseen microlocalization: Municipality of Boyeros, La Habana and Palma Soriano, Santiago de Cuba, Cuba.

General market (demand): The investment allows satisfying the candle demand of the country and creates a space for possible exports to the Caribbean area.

Proposed technology: Tecnologies with a high level of automation, environmentally friendly and in keeping with the present state of the art.

Contacts: Vice-President GEMPIL Telephone: (53) 7 2045184 E-mail: [email protected]



Project title: To boost the production of solar heaters.


General description of the project: It is intended the broadening of productive capacities in the manufacture of solar heaters reaching 30,000 square meters per year and diversifying the range of products to high pressure models that mainly meet the demands of the tourist sector of Cuba. Currently, 10,595 installations nationwide produce energy through solar heaters. Cuba only has technology for manufacturing vacuum tubes, and the national market produces the structure and the tank.

Objectives of the proposal: Access to funding for the acquisition of necessary equipment and working capital

Investment modality: Medium and long-term funding for the execution of the investment Technological alliances for the diversification of the products.

Proposed microlocalization: Carretera Central 1ro.de Enero Km 1 y 1/2" Morón, Ciego de Ávila, Cuba.

General market (demand): 30,000 solar heaters per year.

Proposed technology: Modernization of foaming processes operations, acquisition of tools and measuring instruments for assembly and after-sales services. Technological line for manufacturing high pressure solar heaters

Contacts: Vice-Presidente GESIME. Telephone: (53) 7 263 34 29. E-mail: [email protected]



Project title: Creation of capacities for the production of mops from non-woven fabric.

Cuban part: Light Industry Business Group (GEMPIL).

General description of the project: Currently it is not possible to meet the mops demand with domestic production, taking into

account the increase in costs caused by the technological obsolescence of the industrial plant.

Based on the aforementioned facts, the project is expected to increase productive capacities, and

to allow replacing imports by 18 million units per year, as well as incorporating a product with a

better price / quality ratio to the market. At the same time, it is planned to update and modernize

the technological equipment that ensures the reduction of environmental impact.

Investment modality: Funding for executing the project

Technological Alliances

Proposition of contributions by the foreign part: Funding

Technology

Know How

Training of Cuban personnel

Provision of technological equipment.

Foreseen microlocalization: Road of Viejo del Cobre s/n. Marimón. Santiago de Cuba, Cuba.

General market (demand): The demand certified by market researches reaches 30,000.0 million units, while the current total

available capacity is 5,150.0 million units. The project will cover 77.2% of the current domestic

market demand.

Proposed technology: Spinning equipment (opening, cleaning and carding).

Overcoating and cutting equipment.

Contacts: Vice-President GEMPIL Telephone: (53) 7 204 51 84 E-mail: [email protected]


Project title: Production and commercialization of Rubber Technical Products


General description of the project: Technological modernization, rehabilitation and rescue of the productions and workshops of rubber technical products, as well as the introduction of new productions and workshops.

Investment modality: Joint venture

Proposition of contributions by the foreign part: Funding Know how. Technology transfer. Training of the Cuban technical force in the use of new technologies. Technological equipment.

Proposed microlocalization: Current plan, Cuba.

General market (demand): The proposed investment plans is to increase the productive capacities of molded rubber technical products to meet the demand up to a 70%; to meet 100% of the demand for the "Coloso" soles and to boost the production of technical rubber products for automotive use, ensuring in the short term to cover 50% of the molded products demand.

Proposed technology: The factory must have specific molding, extruding, calendaring and coating technology in rubber; products that have traditionally been manufactured in the country and their processes require rehabilitation. It should also include another range of products that take their generic name according to their shape and / or use, for example: hoses, V-belts, conveyor belts, spring defenses, among others. For manufacturing these items the country does not have the required technology and therefore are acquired abroad.

Contacts: Vice-Presidente GEIQ. Telephone: (53) 7 204 36 12. E-mail: [email protected]


INVESTMENT PROJECT CARD.

Project title: Production and commercialization of radial tires


General description of the project: Assembly of a new plant with clean and advance technology for the production of car tires and light transport tires between (13 to 15) and the heavy transport (bus trucks) ( 20, 22.5 and 24). With modern, energy efficient equipment, including lines of mixing and testing laboratories, allowing the production of competitive radial tires for the domestic market and exports.


Proposition of contributions by the foreign part: Funding Know how. Technology transfer. Training of the Cuban technical force in the use of new technologies Technological equipment.

Foreseen microlocalization: According to the project´s requirements.

General market (demand): The average import of car, buses and truck tires during the period 2008-2013, reached 610,088 tires, of which an estimated 87 percent correspond to radial tires. Based on the above, a plant with a production scale of 1.2 million units has been considered for this project, of which 800,000 units are destined to the domestic market, which determines the need of planning for the export market a figure of 400,000 units. The potential partner must specify the required level of export above the domestic market, according to his previous experience, if necessary.

Proposed technology: The factory must have specific technology for cars and light transport, it has been assessed that they are of mixed radial construction, for a radius of 0.60-0.70. At a future stage, according to the production, the potential supplier will assess the feasibility of including high and ultra high performance tires (HP and UHP). In the case of transport tires, the possible partner will assess the most suitable alternative for producing mixed-technology or all-steel tires.

Contacts: Vice-president GEIQ. Telephone: (53) 7 204 36 12. E-mail: [email protected]



Project title: Production of Disposable Diapers for Children and Adults.


General description of the project: Assembly of a new plant for the production of disposable diapers and fillers for children and adults, with a view to producing 99,400,000 units of diapers for children and 74,100,000 diapers for children, with the sum of both productions meeting the estimated average demand for children . In the case of adult diapers, it is intended to produce 13,200,000 units of diapers and 53,300,000 diapers for adults, meeting with the sum of both productions the estimated low demand. The production will be destined, mainly to the replacement of imports. Located in the Mariel Special Development Zone and favored by its own incentives, it is expected to be linked to the industrial sector.


Proposition of contributions by the foreign part: Funding Know how. Training of the Cuban technical work force in the use of new technologies. Specialized technological and industrial supplies that complement and integrate the Cuban national industry.

Foreseen microlocalization: Mariel Special Development Zone (ZEDM), Cuba.

General market (demand): Taking into account the average projection of births until 2030, 110,000 and of them: 50 thousand children from 0 – 6, 50 thousand children from 6 months to 1 year, 110 thousand children from 1 year to 2 years, in total from 0 to 2 years, 220 thousand children; and taking into account the aging of the population and the possible number of prostrate or incontinent patients estimated at 175,006 and taking into account the estimated minimum demand and the average per day obtained from the analysis of the sales data provided by the chains stores and the MINSAP (0.034 diapers delivered to patients in 2012); taking into account also the comparative analysis between the norms proposed by Cuba, Brazil, some countries of Europe, Peru and Mexico and the real consumption of the latter, the following demand was estimated for our country: Category of the demands CHILDREN ADULTS Average diapers per day Total Diapers per year High Demand 4 316,800,000 3 189,006,480 Average Demand 2.5 198,000,000 2 126,004,320 Low Demand 1 79,200,000 1 63,002,160 Minimum Demand 0.2 13,191,552

Proposed technology: With the creation of the Joint Venture the project intends to acquire technology to produce disposable diapers and fillers, which is defined below: • 2 lines for producing gut type diapers or fillers for children and adults. Both lines should capable of producing 2 sizes, fillings for both children and adults, with speed between 200-300 units of fill per minute, continuous cellulose mattress output, Non woven mattress wrapping, 60Hz voltage, electrical panels for power supply, voltage stabilizer. • 1 line for producing disposable diapers for adults. The line should be capable of producing 3 sizes,

speed of 200 units per minute of adult diapers, continuous cellulose mattress outlet, Non woven mattress wrapping, the diaper must have side anti-leak barriers, front tape and side stickers, 60Hz voltage, power panel for line power, voltage stabilizer, • 1 line for producing disposable diapers for children. The line should be able to produce 4 sizes, speed between 350-400 units of children's diapers per minute, continuous cellulose mattress outlet, Non woven mattress wrapping, the diaper must have lateral anti-leakage barriers, front tape, side and elastic waistband stickers, 60Hz voltage, electrical panel for power supply lines, voltage stabilizer.

Contacts: Vice-President GEMPIL Telephone: (53) 7 204 51 84 E-mail: [email protected]


Project title: Expansion of the production of refractory materials.


General description of the project: It consists in expanding the productive capacity of the Habana Refractory Company, the only one in the country, which would make possible to increase the current production by more than 10 assortments, reduce production costs for steel, reduce dust emissions with extraction systems, better quality control with new equipment for laboratories, automate processes and improve recycling policy. It would be possible to replace imports and to make exports to the countries of Central America and the Caribbean. The main objective of this investment is to increase the use of the installed capacity in the company, the replacement of imports, which would allow ensuring the production of refractory materials for the country's demand and exports. This objective implies to work in the following aspects: -Improve the emission of gases and dust into the atmosphere.

-Maintain quality control. -Automate systems to increase the reliability of processes. -Retrieve necessary technology and apply advance technology. -Continue with the recycling policy.

-Ensure pre and post sales services to customers.

Investment modality: Financing for State Investment.

Proposition of contributions by the foreign part: Funding Know how. Technology transfer. Training of the Cuban technical force in new technologies. Technological equipment.

Foreseen microlocalization: Km 12 ½ San José road, Güines, Mayabeque, Cuba.

General market (demand): The current market comprises the Iron and Steel Industry, Cement, Thermoenergy, Sugar, Nickel, White and Red Ceramics, Incinerators, Small foundries found in the country.

PRODUCTS PROJECTED PRODUCTION

Año 1 Año 2 Año 3 Año 4 Año 5 Año 6

Fireclay production (MTon.) 1,5 4,06 6,125 6,125

bricks (MTon.) 4,920 7,300 7,300 8,600 10,300 12,000

Unformed products (MTon.) 3,103 4,040 6,500 7,450 8,800 11,020

Special parts (MTon.) 0,032 0,025 0,040 0,040 0,055 0,060

TOTAL (MTon.) 8,055 11,365 13,840 16,090 19,155 23,080

DEMAND (MTon.) 20,956 21,584 22,325 22,325 22,325 23,500

Proposed technology: The investment is divided into 4 groups, 3 technological and one covering several activities of a general nature. 1. Rotary Furnace. 2. Fireclay Line. 3. High Alumina Line and Basics.

4. General.

Contacts: Vice-president GESIME. Telephone: (53) 7 263 34 29. E-mail: [email protected]



Project title: Modernization and technological completion of the tannery industry, with the use of its solid and liquid wastes.


General description of the project: Creation of new capacities and closure of production cycles, based on the modernization and technological completion of the Guanajay and Camagüey tanneries, as well as the installation of a finishing plant in the Mariel Special Development Zone. To ensure the sustainability of the industry, it is proposed to set up liquid waste treatment plants for all plants; the technological completion of the factory; and the construction of animal processing plants. It comprises a plant for the integral use of untanned solid waste from tanneries and other industries.

Investment modality: State Investment Joint venture

Proposition of contributions by the foreign part: Funding Know how. Technology transfer. Training of the Cuban technical force in the use of the new technologies. Technological equipment.

Foreseen microlocalization: Caibarien, Camagüey, Artemisa and Boyeros, Cuba. Mariel Special Development Zone (ZEDM),

General market (demand): It is expected to guarantee the demand for footwear and saddlery industries, other forms of non-state production, footwear companies, the Cuban Cultural Property Fund, as well as the export of finished leather and soles.

Proposed technology: The factory must have the most advanced technology in the pre-tanning, tanning, pre-finishing and finishing processes. In particular, is required that the technology guarantees the preservation of the environment.

Contacts: Vice-president GEMPIL Telephone: (53) 7 204 51 84 E-mail: [email protected]


Project title: Modernization and expansion of the productive capacity of the “Vanguardia Socialista” foundry plant.


General description of the project: The aim is to modernize and expand the productive capacities of technological processes: • Forging (tool-stamping) • Carbon steel and manganese smelting • Iron foundry • Heat treating There are 4 independent technological processes that are linked in a productive flow so that the project can be executed in a partial way. The forging workshop is the only one in the country. It is designed to ensure the production of parts and spare parts of equipment of the different branches of the Cuban industry: agriculture, sugar, cement, petroleum, hydraulic resources, food, construction, automotive and rail transport, among others.

Investment modality: Funding for investment Technological alliances and management methods.

Proposition of contributions by the foreign part: Funding Know how. Technology Training of the Cuban technical force in the use of new technologies. Specialized technological and industrial supplies that complement and integrate the Cuban national industry.

Foreseen microlocalization: Municipality of Guanabacoa, Vía Blanca road, La Habana, Cuba.

General market (demand): The demand for forgings is 4,400 tons, cast iron 1,100 tons, and steel 2,500 tons. In addition, 1,000 sets of gear chains are required. Currently only less than 3% of the national demand in steel smelting, 1% iron is met.

Proposed technology:

Automated forging process line and presses.

Automated steel casting process line,

Automated line of cast iron process,

Automated heat treatment process line

Automated processing and machining lines

Semi-automated design center,

Comprehensive computerization and control system,

Automated molding and feeding systems,

Automated processes of molding and demolding,

Mechanical center for the production of stamps.

Installation of modern systems of chemical-thermal treatment.

CN and CNC machines in metal and wood machining equipment

Direct quality control means on production lines.

Contacts: Vice-president GESIME. Telephone: (53) 7 263 34 29, E-mail: [email protected]


Project title: Modernization and expansion of the productive capacity of the “Inoxidables Varona”

metallurgical plant


General description of the project: It is planned the modernization and expansion of the production volumes. The project also

seeks to introduce new productions with advance technologies for the manufacture of

equipment that is currently imported to food processing plants, small industries, equipment,

parts and spare parts.

In parallel, the aim is to increase the levels of integration of the national industry in the

participation of projects of comprehensive plants both in Cuba and abroad, further

enhancing the exports of the sector.

Increase the levels of automation of manufacturing processes of technological equipment

directed to priority sectors of the food program.

Investment modality: Funding for the execution of the investment. Technological alliances and management methods.

Proposition of contributions by the foreign part: Funding Know how. Training of the Cuban technical force in the use of new technologies. Specialized technological and industrial supplies that complement and integrate the Cuban

national industry.

Foreseen microlocalization: Carretera del Cuervo y Dolores, Municipality of San Miguel del Padrón, La Habana, at 23o

04´56,16¨ N and 82o 19´45,12¨ W

General market (demand): Currently a large part of the technological equipment required for the food and agricultural processing industries are imported. The main demands come from:

Food Industry Plants (milk, rum, bread, preserves)

Livestock Program, mainly linked to milk.

Food processing industries of different capacities.

Production of feed factories and storage silos.

Components and parts linked to bioproducts, biopesticides

Beekeeping plants of the country.

Parts for the cement industry.

Parts, components, and construction parts for Construction Materials.

Plants for vegetables, fruits.

Construction of new plants linked to the country's defense.

Tourist facilities.

Other demanding sectors are: sugar industry, automotive transportation, Electrical Industry, Railway Transport, Agricultural Equipment, Oil Industry, Hydraulic Resources Industry, Biotechnology Industry and others.

Proposed technology:

Vertical winch plate diameter of 1000 mm, for parts with a maximum height of 1200 mm.

Laser cutting line for sheet metal coils from 1.2 to 4 mm in stainless steel.

Plasma cutting equipment.

Automatic punch with turret of 19 stations for 1.2 up to 4mm.

Vertical welding manipulator.

Welding by washer for plates of 0.8 to 4 mm in stainless steel.

Horizontal welding manipulator for the rolls of the tanks.

Sheet welder for 0.8 mm to 4 mm stainless steel welding.

Square and round pipe cutter Φ22.4 to 75 mm with base from 0º to 180º.

Multiple shears for the cutting of angular bars, plates, as well as for the punching of plates.

Machine for making of spherical caps, capacity up to 8 mm and maximum diameter 2000 mm.

Round tube bender from 22.4 mm to 40 mm in stainless steel with horizontal and vertical repositioning, maximum diameter 90 mm.

200 ton hydraulic press with 600x 600 mm working table.

Press-break of 160 tons, working length 3200 mm, capacity for folding of sheets up to 10 mm in stainless steel.

Circular sheet cutter for tank lids, capacity 1.2 to 8 mm in stainless steel, maximum diameter 2000 mm, minimum 250 mm.

Cutting shear from 3.0 up to 10.0 mm in long stainless steel 3100 mm.

Equipment for corner cutting, variable angle, cutting thickness 6 mm, cutting length 200 mm, cutting angle range 45 ° - 135 °.

4-mass horizontal long cylinder.

CNC lathe with 45o inclined bench, 3 axes, distance between plate and point 1500 mm, maximum diameter 250 mm, with motorized tower of 15 positions.

Mechanical and circular saw.

Universal CNC milling machine.

Finishing and polishing equipment for the finishing of tanks, pieces and equipment in stainless steel.

TIG welding equipment with water cooling.

Contacts Vice-president GESIME. Telephon: (53) 7 263 34 29. E-mail: [email protected]


Project title: Increased integration of the National Industry of Cuba in the construction of Photovoltaic Solar Plants.

Cuban part: Electronics, Automatic and Communications Industrial Group (GELECT)

General description of the project: Increased production capacities of inverters and control boards of solar photovoltaic plants connected to the national electricity grid. To create design capacities of solar photovoltaic plants connected to the electricity network. Production of Batteries for energy storage. Supply and funding, in the medium term and on advantageous conditions, of the necessary raw materials.

Investment modality: Funding for the execution of the project. Joint venture

Proposition of contributions by the foreign part: Funding Know how. Training of the Cuban technical force in the use of new technologies. Specialized technology supplies that complements and integrates the Cuban national industry.

Foreseen microlocalization: To be decided

General market (demand): Production will meet the demand for 700 MWp by 2030, as part of the Policy for the Perspective Development of Renewable Sources and Energy Efficiency, as well as for exports in the Caribbean and Central American region.

Proposed technology: Automated line with high flexibility and production capacity of inverters and slates. Battery assembly line with lithium cell technology. It also includes the general conditions of auxiliary and storage services, as well as all necessary laboratory equipment and tests.

Contacts: Vice-president GELECT. Telephone: (53) 7 204 1191. E-mail: [email protected]



Project title: National integration of Planning, Construction and Installation of Treatment Plants and Water Desalination Plants.

Cuban part: Electronics, Automatic and Communications Industrial Group (GELECT).

General description of the project: Creation of the design and manufacturing capacities of treatment plants and water desalination plants, which allows the realization of designs according to the international standards in this field and bring the supplies to manufacturers or large distributors of the most important elements. Create a service network that reaches the whole country and ensures the sustainability and uninterrupted operation of the equipment deployed in these plants with remote diagnosis. Use of renewable energy sources. Supply and funding, in the medium term and on advantageous conditions, of the necessary raw materials.

Investment modality: Medium and long-term funding Joint venture

Proposition of contributions by the foreign part: Funding Know how. Training of the Cuban technical force in the use of new technologies. Specialized technology and component supplies.

Foreseen microlocalization: To be decided. In Cuba there is the Electronic Components Company of Pinar del Rio with experience in the treatment of water that could be considered.

General market (demand): For the general population are estimated 200 plants, total capacity 3000 m3 / h, For tourism facilities (hotels, infrastructure, services, etc.) in the process of rising capacities, nearly 2000 m3 / h are estimated. For the industry: still in the process of identifying the demand.

Proposed technology: High-level automation and control plants for the treatment and desalination of sea water using reverse osmosis technology, adjusted to modular capacities. Advance membrane suppliers, pumps and recovery systems.

Contacts: Vice-president GELECT. Telephone: (53) 7 204 1191. E-mail: [email protected]



Project title: Production and commercialization of polyethylene flexible printed and extrusion material for packaging


General description of the project: Creation of the productive capacities from the acquisition of technological equipment for the pre-printing process, which includes digitized system for image processing and engraving, from the computer to the flexographic plate, equipment for flexographic printing of flexible material in rolls, 6-color printing machines in order to meet the national demand above a 93%. It is complemented in the national industry with the production of packaging for the food industry, agriculture, products of the light industry that includes sanitary pads, diapers, footwear, soaps, detergents, clothing, and chemical products for the Geo-Mining industry

Investment modality: Medium and long-term funding Joint Venture

Proposition of contributions by the foreign part: Funding Know how. Training of the Cuban technical force in the use of new technologies. Specialized technology and component supplies. Technological equipment.

Foreseen microlocalization: Carretera Central Km 40 San José de las Lajas, province of Mayabeque, Cuba.

General market (demand): General demand of 8,000 tons, including milk containers in its different forms, yogurt, pasta, coffee, salt, sugar, rice, grains, cereals, soft drinks, soaps, solid detergents, sanitary pads, disposable diapers and bags for packaging industrial products and food.

Proposed technology: High-level automation and control plants.

Contacts: Vice-president GEMPIL Telephone: (53) 7 204 51 84 E-mail: [email protected]

investment project card - izvozno okno profiles fuera de cartera.pdf · investment project card ......

Documents