kitco ltd construction of municipal stadium at … · to the required slope and compacting as per...
TRANSCRIPT
-
Sl.No Description Of Items Unit Quantity Rate(Rs) Rate in wordsAmount
(Rs)
SH :1 EARTHWORK
1.01Clearing grass and removal of the rubbish up to a distance of 50 m
outside the periphery of the area cleared.sqm 24245.00 4.41 Rupees Four And Paise Forty One Only 106920
1.02Surface dressing of the ground including removing vegetation and in-
equalities not exceeding 15cm deep and disposal of rubbish, lead upto
50m and lift upto 1.5m.
All kinds of soil sqm 23905.00 16.43 Rupees Sixteen And Paise Forty Three Only 392759
1.03
Earth work in excavation by means (Hydraulic excavator)/manual
means over areas (exceeding 30cm in depth.1.5m in width as well as
10 sqm on plan) including disposal of excavated earth, lead upto 50 m
and lift upto 1.5 m; disposed earth to be levelled and neatly dressed,
as directed by the Engineer- in-Charge
All kinds of soil. cum 375.00 169.78Rupees One Hundred Sixty Nine And Paise
Seventy Eight Only63668
1.04Do same as above item no. 1.03 but for every additional lift of 1.5m to
3.00m or part there of :All kinds of soilcum 37.00 234.34
Rupees Two Hundred Thirty Four And Paise
Thirty Four Only8671
1.05
Filling in plinth or trenches, under floors, foundations, in areas etc.
with red earth including watering, ramming consolidating and dressing,
cost and conveyance of all materials,labour charges,lead,lift etc
complete at all levels as directed by the Engineer- in-Charge
cum 57.00 743.89Rupees Seven Hundred Forty Three And
Paise Eighty Nine Only42402
1.06
Filling available excavated earth(excluding rock) in trenches, under
floors,plinth,sides of foundation,in areas etc. in layers not exceeding
20cm in depth,consoldating each deposited layer by ramming and
watering,lead upto 50m and lift upto 1.5m including cost and
conveyance of all materials,labour charges, etc complete at all levels
as directed by the Engineer-in-Charge
cum 110.00 126.99Rupees One Hundred Twenty Six And Paise
Ninety Nine Only13969
KITCO LTD
Construction of Municipal Stadium at Chengannur
SPECIFICATION AND SCHEDULE OF QUANTITIES - PART A- CIVIL WORKS
Tenderer 139 ChiefEngineer
-
Sl.No Description Of Items Unit Quantity Rate(Rs) Rate in wordsAmount
(Rs)
1.07
Excavating trenches of required width for pipes, cables, etc. including
excavation for sockets, and dressing of sides, ramming of bottoms,
depth up to 1.5m including getting out the excavated soil, and then
returning the soil as required, in layers not exceeding 20 cm in depth
including consolidating each deposited layer by ramming, watering,
etc. and disposing of surplus excavated soil and unserviceable
material as directed, within a lead of 50 m All kinds of soil
Pipes, cables etc. not exceeding 80mm dia m 50.00 141.26Rupees One Hundred Forty One And Paise
Twenty Six Only7063
1.08
Bailing out water from well with 5HP Engine and pump set including
conveyance to the site and erection, cost of fuel, lubricating oil and
other stores etc. complete as directed by the Engineer- in-Charge.
hr 92.00 193.75Rupees One Hundred Ninety Three And
Paise Seventy Five Only17825
1.09Consolidation of earth by ramming in 15 cm layers including watering
cost and conveyance of all materials ,labour charges etc complete as
directed by the Engineer- in-Ccharge.
cum 19124.00 30.66 Rupees Thirty And Paise Sixty Six Only 586342
1.10Extra for additional lead upto 100m over initial lead of 50m for
disposing surplus excavated earth as per the direction of Engineer-in-
Charge.
cum 3808.75 74.45Rupees Seventy Four And Paise Forty Five
Only283561
1.11
Providing and filling the areas with good quality red earth brought from
outside with all leads and lifts, transporting to site, spreading, grading
to the required slope and compacting as per MORT&H specification
Section 305 including cost and conveyance of all materials,labour
charges ,lead,lift etc complete as directed by the Engineer- in-Charge
cum 19124.00 761.00 Rupees Seven Hundred Sixty One Only 14553364
1.12
Providing and filling the areas with good quality red earth available at
the site with all leads and lifts, transporting to site, spreading, grading
to the required slope and compacting as per MORT&H specification
Section 305 including cost and conveyance of all materials,labour
charges ,lead,lift etc complete as directed by the Engineer- in-Charge
cum 240.00 167.00 Rupees One Hundred Sixty Seven Only 40080
Tenderer 140 ChiefEngineer
-
Sl.No Description Of Items Unit Quantity Rate(Rs) Rate in wordsAmount
(Rs)
1.13
Boring ,providing and installing bored cast-in-situ single under reamed
piles of specified diametre and length below the pile cap in M35 mix in
cement concrete to carry a safe working load not less than specified
excluding the cost of steel reinforcement but including the cost of
boring with ,bentonite solution and the length of the pile to be
embedded in the pile cap,chipping the pile etc all complete (Length of
pile for payment shall be measured up to bottom of pile cap)
450mm dia. m 100.00 3078.41Rupees Three Thousand Seventy Eight And
Paise Forty One Only307841
1.14
Arranging and conducting vertical load testing of piles in accordance
with IS.2911 (Part IV ) including installation of loading platform and
preparation of pile head or construction of test cap and dismantling of
test cap after test etc complete as per specification & the direction of
Engineer - in - Charge.
Single pile up to 50 Tonne capacity
1.14.1 Initial test no 2.00 55125.26Rupees Fifty Five Thousand One Hundred
Twenty Five And Paise Twenty Six Only110251
Single pile up to 50 Tonne capacity
1.14.2 Routine test. no 2.00 24905.99Rupees Twenty Four Thousand Nine
Hundred Five And Paise Ninety Nine Only49812
TOTAL OF SUB HEAD -1.0 16584527
(SH: - 2.0 - CONCRETE WORK)
2.01
Providing and laying cement concrete of specific grade properly mixed
and consolidated with hand rammers, including cost and conveyance
of all materials, labour, curing, lead lift , etc. complete for all work up
to plinth levels as directed by Engineer- in-Charge.
2.01.011:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm
nominal size)cum 85.00 5618.69
Rupees Five Thousand Six Hundred
Eighteen And Paise Sixty Nine Only477589
TOTAL OF SUB HEAD -2.0 477589
Tenderer 141 ChiefEngineer
-
Sl.No Description Of Items Unit Quantity Rate(Rs) Rate in wordsAmount
(Rs)
(SH: - 3.0 - R.C.C. WORK)
3.01
Providing and laying in position machine batched, machine mixed and
machine vibrated design mix M-25 grade cement concrete for
reinforced cement concrete using cement content as per approved
design mix including pumping of concrete to site of laying but,
excluding the cost of centering, shuttering, finishing and reinforcement
including admixtures in recommended proportion (as per IS 9103) to
accelerate,retard setting of concrete to improve workability without
impairing strength and durability as per direction of Engineer-in-
Charge .Cement content considered in this item is @ 330 kg/cum
All work upto plinth level. cum 161.00 7821.46Rupees Seven Thousand Eight Hundred
Twenty One And Paise Forty Six Only1259255
3.03
Providing and laying in position machine batched, machine mixed and
machine vibrated design mix M-25 grade cement concrete for
reinforced cement concrete using cement content as per approved
design mix including pumping of concrete to site of laying but,
excluding the cost of centering, shuttering, finishing and reinforcement
including admixtures in recommended proportion (as per IS 9103) to
accelerate,retard setting of concrete to improve workability without
impairing strength and durability as per direction of Engineer-in-
Charge .Cement content considered in this item is @ 330 kg/cum
All work above plinth level upto floor V level. cum 2.00 8644.68Rupees Eight Thousand Six Hundred Forty
Four And Paise Sixty Eight Only17289
3.04
Providing ,hoisting and fixing upto floor five level precast cement
concrete string or lacing courses, copings, bed plates, anchor blocks,
plain window sills, shelves, louvers, steps, stair cases, slabs,brackets
etc. including hoisting and setting in position with cement mortar 1:3 (1
Cement : 3 coarse sand), cost of required centering, shuttering and
finishing smooth with 6mm thick cement plaster 1:3 (1 Cement : 3 fine
sand) on exposed surfaces complete.but excluding the cost of
reinforcement with1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm
nominal size) cum 44.00 7741.92
Rupees Seven Thousand Seven Hundred
Forty One And Paise Ninety Two Only340644
Tenderer 142 ChiefEngineer
-
Sl.No Description Of Items Unit Quantity Rate(Rs) Rate in wordsAmount
(Rs)
3.05
Reinforcement for R.C.C. work including straightening, cutting,
bending, placing in position and binding with 16 gauge GI binding wire
etc complete including cost, conveyance, lead, lift of all materials for
all types of RCC works as per drawing/specification and as directed by
Engineer-in-Charge at all levels.
Thermo-Mechanically Treated bars kg 20678.00 73.71RupeesSeventy Three And Paise Seventy
one Only1524175
3.06Centering and shuttering including strutting, propping etc. and removal
of form for :
3.06.01 Foundations, footings, bases of columns etc. for mass concrete. sqm 94.00 217.26Rupees Two Hundred Seventeen And Paise
Twenty Six Only20422
3.06.02 Suspended floors, roofs, landings, balconies and access platform. sqm 18.00 476.44Rupees Four Hundred Seventy Six And
Paise Forty Four Only8576
3.06.03 Lintels, beams, plinth beams, girders, bressumers and cantilevers. sqm 122.00 384.58Rupees Three Hundred Eighty Four And
Paise Fifty Eight Only46919
3.06.04 Columns, Pillars, Piers, Abutments, Posts and Struts. sqm 13.00 522.82Rupees Five Hundred Twenty Two And
Paise Eighty Two Only6797
3.06.05 Edges of slab and breaks in floors and walls under 20 cms wide m 1219.00 125.20Rupees One Hundred Twenty Five And
Paise Twenty Only152619
3.06.06Walls of (any thickness)including attached pilasters butteresses plinth
and string course etc.sqm 678.00 426.37
Rupees Four Hundred Twenty Six And Paise
Thirty Seven Only289079
TOTAL SUB HEAD-3.0 3665776
(SH: - 4.0 - MASONRY WORK)
4.01
Providing and constructing Solid block masonry M-10 grade(mix
1:3:6)(1;cement ,3:crusher sand,6: 6mm metal) in C.M1:6(1cement, 6
coarse sand) with Solid blocks of 30x20x15 cm size and approved
quality including scaffolding, raking out of joints,curing, cost and
conveyance of all materials,labour, lead, lift, etc. complete for all types
of masonry works in below the highest plinth level as directed by
Engineer-in-Charge.
4.01.01 Supply cum 15.00 2785.28Rupees Two Thousand Seven Hundred
Eighty Five And Paise Twenty Eight Only41779
Tenderer 143 ChiefEngineer
-
Sl.No Description Of Items Unit Quantity Rate(Rs) Rate in wordsAmount
(Rs)
4.01.02 Laying cum 15.00 2271.68Rupees Two Thousand Two Hundred
Seventy One And Paise Sixty Eight Only34075
4.02
Soling 230 mm thick with soling stone of size 150 to 75 mm
brokenstone and blinding materials, including hand packing and
wedging them tightly so that the whole is formed as a solid mass,
spreading blinding material in 12mm thick layers and sweeping the
same to fill the voids,watering profusely and consolidating with hand
rammer/ plate vibrator etc complete as per the direction of Engineer-in
- Charge.
cum 5.00 1881.56Rupees One Thousand Eight Hundred
Eighty One And Paise Fifty Six Only9408
4.03
Providing and constructing brick masonry in C.M 1:6 (1 cement, 6
coarse sand) with country burnt bricks of 22.9x11.2x7 cm size and
approved quality (average compressive strength not less than 35
kg/cm2) including scaffolding, raking out of joints, curing, cost and
conveyance of all materials, labour,lead, lift, etc. complete for
foundation, trenches, basement etc. below highest plinth level as
directed by Engineer-in-Charge at all levels
cum 1.00 5078.73Rupees Five Thousand Seventy Eight And
Paise Seventy Three Only5079
TOTAL SUB HEAD 4.0 90341
(SH: - 5.0 - JOINERY WORKS )
5.01
Providing and fixing powder coated aluminium work for doors
,windows& partitions with extruded built up standard tubular
sections/appropriate Z sections & other sections of approved make
confirming to IS:733 & IS:1285 fixed with rawl plugs & screws or with
fixing clips including necessary filling up of gaps at junctions,at
top,bottom & sides with required PVC/neoprene felt etc.Aluminium
sections shall be smooth,rust free,straight,mitred & jointed
mechanically where ever required including cleat angle,aluminium
snap beading for glazing/panelling,cp brass/stainless steel screws all
complete as per architectutral drawings & directions of Engineer-in-
Charge at all levels.(glazing & panelling to be paid
seperately).Minimum thickness of powder coating for powder coated
Aluminium shall be 50 micron
5.01.01 For fixed portion kg 217.00 403.52Rupees Four Hundred Three And Paise Fifty
Two Only87564
Tenderer 144 ChiefEngineer
-
Sl.No Description Of Items Unit Quantity Rate(Rs) Rate in wordsAmount
(Rs)
5.01.02
For shutter of doors ,windows & ventilators including providing and
fixing hinges/pivots and making provision for fixing of fittings,exhaust
fan of required size,etc wherever required including the cost of PVC
neoprene gasket required(fittings shall be paid for separately)
kg 326.00 470.14Rupees Four Hundred Seventy And Paise
Fourteen Only153266
5.02
Providing and fixing glazing in aluminium doors,windows,ventilator
shutters,partitions etc. with PVC/ neoprene gasket etc. complete as
per the architectural drawings and the directon of Engineer-in-Charge
at all levels
5.02.01 with float glass panes of 4.00mm thickness sqm 37.00 890.46Rupees Eight Hundred Ninety And Paise
Forty Six Only32947
5.03
Providing and fixing 150 mm aluminium handles ISI marked anodised
(anodic coating not less than grade AC 10 as per IS : 1868)
transparent or dyed to required colour or shade with necessary screws
etc. complete as directed by Engineer -in-Charge at all levels.
no 8.00 67.34Rupees Sixty Seven And Paise Thirty Four
Only539
5.04
Providing and fixing bright finished brass100mm mortice latch and
lock ISI marked with 6 levers and a pair of anodised(anodic coating
not less than grade AC 10 as per IS:1868)aluminium lever handles
with necessary screws etc. complete at all levels.(best make of
approved quality).
no 8.00 594.12Rupees Five Hundred Ninety Four And Paise
Twelve Only4753
5.05
Providing and fixing 100 x 10 mm aluminium tower bolts ISI marked
anodised (anodic coating not less than grade AC 10 as per IS : 1868)
transparent or dyed to required colour or shade with nuts and screws
etc. complete as directed by the Engineer-in-Charge at all levels.
no 16.00 51.08 Rupees Fifty One And Paise Eight Only 817
5.06
Providing and fixing aluminium hanging floor door stopper ISI marked
anodised (anodic coating not less than grade AC 10 as per
IS:1868)transparent or dyed to required colour and shade with
necessary screws etc complete as directed by the Engineer-in -
Charge at all levels.
Single rubber stopper no 8.00 57.42Rupees Fifty Seven And Paise Forty Two
Only459
5.07Supplying and fixing MS oxidized Hooks & Eyes as directed by the
Engineer- in-Charge.
200mm no 54.00 11.69 Rupees Eleven And Paise Sixty Nine Only 631
Tenderer 145 ChiefEngineer
-
Sl.No Description Of Items Unit Quantity Rate(Rs) Rate in wordsAmount
(Rs)
5.08
Supplying and fixing FRP frames made of glass fibre conforming to
IS:11551-1986, glass fibre rovings conforming to IS:11390-
1985,isophthalic resin conforming to IS: 6746-1972, curing
agents,accelerators, fillers, additives, fire retardants and pigments as
specified. The frames shall be contact moulded by laying gelcoat at
500gm/m2 and laid over with two layers of FRP mat (one layer of 300
CSM mat and one layer of 450 CSM mat). The CSM mat shall be
bonded with isophthalic resin and fillers of additives by weight. The
edges shall be sealed with gelcoat and FRP mat to obtain smooth
finish. The frames shall have an overall size of 100x63mm including
the thickness of FRP and shall be filled with seasoned treated rubber
wood on the inside. Suitable depressions shall be made in the door
frames for receiving the fixtures such as hinges, mortice lock as well
as 30mm door shutter. (one number mortice lock at the centre and
three numbers of 100mm heavy duty hinges). The rate shall include
providing and fixing frames of approved colour for, providing and fixing 6 Nos. of flat iron hold fast of
size 300mmx30mmx3mm using stainless steel screws, fixing in PCC
1:2:4 blocks, finishing the joints to match the surroundings and
finishing the frames by buffing and polishing with wax as directed.
(The contractor shall supply 1 No. of frames free of cost for every 10
Nos. of frames supplied at site or part thereof for destructive testing)
The shutter shall be contact moulded by laying gelcoat at 500gm/m2
and laid over with two layers of FRP mat (one layer of 300 CSM mat
and another layer of 450 CSM mat) for each of the web (panels) and
two layers of FRP mat (one layer of 300 CSM mat and another layer of
450 CSM mat) for the flange portion (rails and styles). The CSM mat
shall be bonded with isophthalic resin in
the ratio of not less than 1:2 (one part of mat : 2 part of isopthalic resin
and fillers and additives) by weight. The edges shall be sealed with
gelcoat and FRP mat to obtain smooth finish. The shutter/frames shall
have an overall thickness of 30mm with a width of 100mm for outer
frames and 80mm for resin frames (as per drawings enclosed). The
shutter frames shall be provided with treated and seasoned rubber-
wood on the insides to receive the tower bolts, handle, mortise lock,
hinges, door closers, etc. at specified locations. Suitable depressions
shall be made in the shutter frames for receiving the hinges and
concealed mortise locks. The rates shall include providing and fixing
shutter of approved colour in the frames already provided and fixed,
Tenderer 146 ChiefEngineer
-
Sl.No Description Of Items Unit Quantity Rate(Rs) Rate in wordsAmount
(Rs)
including fittings such as hinges, tower bolts, handles, door closers,
mortice locks, etc. but excluding the cost of door fittings. The shutter
shall be buffed and polished with wax as directed. The thickness of
FRP laminate of hollow rails and styles shall be minimum 2mm and
thickness of FRP laminate used for panel in shutter shall be minimum
3mm.(Mode of measurement: Length shall be taken as back to back
of outer frame and the height shall be taken from the Sill to the top of
the outer frame)
sqm 24.00 5906.23Rupees Five Thousand Nine Hundred Six
And Paise Twenty Three Only141750
TOTAL OF SUB HEAD-5.0 422726
(SH: - 6.0 - STEEL WORK)
6.01
Steel work welded in built up sections/framed work including cutting
hoisting, fixing in position and applying two coats of approved make
and colour synthetic enamel paint over two coats of approved make
anticorrossive yellow zinc chromate primer, etc. including cost and
conveyance of all materials, labour, lead,lift etc. complete as directed
by Engineer- in-Charge at all levels.
In gratings, frames, guard bar, ladders, railings, brackets, gates &
similar works.kg 269.00 105.55
Rupees One Hundred Five And Paise Fifty
Five Only28393
6.02
Providing cast iron Gate as per drawing and fixing in position including
painting with two coat of anticorrossive yellow zinc chromate primer
and two coats of synthetic enamel paint of approved quality and
colour, including cost and conveyance of all materials, labour charges
etc, complete as directed by the Engineer in Charge
@ 60 kg/m2
new gate kg 1916.00 85.00 Rupees Eighty Five Only 162860
TOTAL OF SUB HEAD-6.0 191253
(SH: - 7.0 - FLOORING WORK)
Tenderer 147 ChiefEngineer
-
Sl.No Description Of Items Unit Quantity Rate(Rs) Rate in wordsAmount
(Rs)
7.01
Providing and fixing Vitrified floor tiles 600x600x9 mm of Ist quality
conforming to IS : 15622 of approved make,shade,and pattern laid on
20 mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand) and
jointed with grey cement slurry @ 3.3 kg/sqm including pointing in
white cement mixed with pigment of matching shade .including cost
and conveyance of all materials,labour charges,lead,lift etc, complete
as directed by the Engineer in Charge(The purchase price of tiles
should be taken as Rs.715/sqm and any deviation plus or minus in the
purchase price in approved shade will be adjusted in the price
quoted).
Size of Tile 60x60 cm sqm 67.00 1307.85Rupees One Thousand Three Hundred
Seven And Paise Eighty Five Only87626
7.02
Providing and laying Antiskid Ceramic floor tiles 300x300x7 mm of
Ist quality conforming to IS : 15622 of approved make,shade,and
pattern laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse
sand) and jointed with grey cement slurry @ 3.3 kg/sqm including
pointing the joints with white cement and matching pigment
etc.including cost and conveyance of all materials,labour
charges,lead,lift etc, complete as directed by the Engineer in Charge
at all levels.(The purchase price of tiles should be taken as
Rs.400/sqm and any deviation plus or minus in the purchase price in
approved shade will be adjusted in the price quoted)
sqm 117.00 961.52Rupees Nine Hundred Sixty One And Paise
Fifty Two Only112498
7.03
Providing and fixing 1st quality ceramic glazed wall tiles conforming to
IS : 15622(thickness to be specified by the manufacture of approved
make in all colours , shades except burgundy, bottle green, black of
any size as approved by Engineer-in- charge in skirting, risers of steps
and dados over 12mm thick bed of cement Mortar 1:3 (1 cement: 3
coarse sand) and jointing with grey cement slurry@ 3.3kg per sqm
including pointing in white cement mixed with pigment of matching
shade complete.(The purchase price of tiles should be taken as
Rs.414/sqm and any deviation plus or minus in the purchase price in
approved shade will be adjusted in the price quoted)
sqm 290.00 1004.33Rupees One Thousand Four And Paise
Thirty Three Only291256
Tenderer 148 ChiefEngineer
-
Sl.No Description Of Items Unit Quantity Rate(Rs) Rate in wordsAmount
(Rs)
7.04
Providing and laying 16 to 20 mm thick polished granite slab with edge
rounding & polishing if required of approved colour,make and pattern
on floors, top of counter slabs, skirting, treads of steps, landings etc.,
including an underlayer of cement mortar 1:4 ( 1 cement : 4 coarse
sand) 20mm thick and cement slurry @ 3.3kg of cement per sqm,
finished with flush pointing using approved joint filler of matching
shade including cost and conveyance of all materials labour
etc.complete as directed by Engineer-in-Charge at all levels
sqm 6.00 3383.68Rupees Three Thousand Three Hundred
Eighty Three And Paise Sixty Eight Only20302
7.05
Extra for providing edge moulding to 16 to 20mm thick marble/granite
counters, Vanities etc. including machine polishing to edge to give
high gloss finish,triple step groove etc. complete as per design and as
approved by Engineer-in-Charge at all levels.
m 10.00 312.54Rupees Three Hundred Twelve And Paise
Fifty Four Only3125
7.06
Extra for providing opening of required size & shape for wash basins/
kitchen sink in kitchen platform, vanity counters and similar location in
marble/granite work including providing necessary holes for pillar taps
etc. including rubbing and polishing of cut edges etc. complete as
directed by the Engineer-in-Charge at all levels.
no 10.00 499.77Rupees Four Hundred Ninety Nine And
Paise Seventy Seven Only4998
TOTAL OF SUB HEAD-7.0 519805
Tenderer 149 ChiefEngineer
-
Sl.No Description Of Items Unit Quantity Rate(Rs) Rate in wordsAmount
(Rs)
(SH: - 8.0 - ROOFING WORK)
8.01
Providing and fixing on wall face unplasticised - Rigid PVC rain water
pipes conforming to IS : 13592 Type-A including jointing with seal ring
conforming to IS:5382 leaving 10mm gap for thermal expansion.
8.01.01 Single socketed pipes
110mm diameter OD m 24.00 244.40Rupees Two Hundred Forty Four And Paise
Forty Only5866
TOTAL OF SUB HEAD-8.0 5866
(SH: - 9.0 - FINISHING WORK)
9.01
12mm cement plaster of mix 1:4 (1 cement : 4 fine sand)including
cost and conveyance of all materials, labour charges, scaffolding,
sundries etc complete as directed by the Engineer in charge at all
levels.
sqm 810.00 195.40Rupees One Hundred Ninety Five And Paise
Forty Only158274
9.02
15mm cement plaster of mix 1:4 (1 cement : 4 fine sand)including
cost and conveyance of all materials, labour charges, scaffolding,
sundries etc complete as directed by the Engineer in charge at all
levels.
sqm 13.00 227.51Rupees Two Hundred Twenty Seven And
Paise Fifty One Only2958
9.03
15mm cement plaster of mix, 1:3 (1 cement : 3 fine sand) finished with
a floating coat of neat cement 2 kg/sqm including mixing water
proofing material in separately).proportion recommended by
manufacturer over roof at all heights including cost and conveyance of
all materials, labour charges, scaffolding, sundries etc complete as
directed by the Engineer in charge at all levels. (water proofing liquid
will be paid separately)
sqm 228.00 307.64Rupees Three Hundred Seven And Paise
Sixty Four Only70142
9.04
Applying one coat of cement primer of approved brand and
manufacture on wall surface including cost and conveyance of all
materials, labour charges, scaffolding, sundries etc complete as
directed by the Engineer in charge at all levels.
sqm 13.00 36.19 Rupees Thirty Six And Paise Nineteen Only 470
TOTAL OF SUB HEAD-9.0 231844
Tenderer 150 ChiefEngineer
-
Sl.No Description Of Items Unit Quantity Rate(Rs) Rate in wordsAmount
(Rs)10.00 (SH: - 10.0 - SANITARY INSTALLATION)
10.01
Supplying and fixing European type floor mounted white glazed WC
with trap including seat cover, with CP brass hinges and rubber
buffers, 10 litres capacity PVC low level white flushing cistern with
fittings and brackets, 40mm dia PVC flush bend over flow pipe with
mosquito proof arrangements,with all necessary fittings complete
including cutting and making good the walls and floors etc. complete
as directed by the Engineer-in-Charge. (The purchase price
considered for EWC is Rs.1250 seat cover is Rs.390,cistern is
Rs1120and any deviation plus or minus in the purchase price will be
adjusted in the price quoted).
no 6.00 5140.88Rupees Five Thousand One Hundred Forty
And Paise Eighty Eight Only30845
10.02
Providing and fixing coloured vitreous china counter top round wash
basin 470 mm or nearest size of approved make including one CP
brass pillar cock 15 mm NB including connecting pipes with all fittings
32 mm dia rubber plugs 32 mm dia CP brass waste coupling, 32 mm
dia CP brass bottle trap, 15mm angle valve, etc. complete as directed
by the Engineer-in-charge. (The purchase price considered for
washbasin is Rs.1580, pillar cock is Rs.325,bottle trap is Rs
1050,angle valve is Rs 450 and any deviation plus or minus in the
purchase price will be adjusted in the price quoted).
10.02.01 Supply no 10.00 3054.75Rupees Three Thousand Fifty Four And
Paise Seventy Four Only30547
10.02.02 Fixing no 10.00 1849.28Rupees One Thousand Eight Hundred Forty
Nine And Paise Twenty Eight Only18493
10.03
Providing and fixing white vitreous china flat back large urinal of
590x390x375 or nearest size of approved make with fittings, standard
size CP brass flush pipe, spreaders with unions and clamps (all in CP
brass) with waste fitting as per IS:2556, CI trap with outlet grating and
other couplings in CP brass including paintings of fittings and
brackets, cutting and making good the walls and floors whereveer
required.Single half stall urinals with 5 litre PVC automatic flushing
cistern (The purchase price considered for urinal is Rs.1023 and any
deviation plus or minus in the purchase price will be adjusted in the
price quoted).
no 5.00 6840.53Rupees Six Thousand Eight Hundred Forty
And Paise Fifty Three Only34203
Tenderer 151 ChiefEngineer
-
Sl.No Description Of Items Unit Quantity Rate(Rs) Rate in wordsAmount
(Rs)
10.04
Supplying and fixing approved quality white vitreous china urinal
division plate 700 x 340 including cost and conveyance of all material,
labour charge, lead, lift, all taxes etc. complete as directed by the
Engineer-in-Charge. (The purchase price considered for division plate
is Rs.479, and any deviation plus or minus in the purchase price will
be adjusted in the price quoted).
no 4.00 629.94Rupees Six Hundred Twenty Nine And Paise
Ninety Four Only2520
10.05
Providing and fixing frameless mirror, with all four edges machine
polished and back side protected with safety film and 4 mm thick
Plywood backing and fixed on walls with mirror screws. The rate
includes lifting, cutting etc. as per design and drawing. (The purchase
price considered is Rs 3200/- any deviation plus or minus in the
purchase price will be adjusted in the price quoted.)
sqm 6.00 3716.80Rupees Three Thousand Seven Hundred
Sixteen And Paise Eighty Only22301
10.06
Providing and fixing CP brass long body bib cock of approved quality
conforming to IS standards and weighing not less than 690 gms
including cost and conveyance of all materials, labour charges,
sundries etc complete as directed by the Engineer in charge at all
levels (The purchase price considered is Rs 415/-any deviation
plus or minus in the purchase price will be adjusted in the price
quoted).
15 mm nominal bore no 14.00 505.12 Rupees Five Hundred Five And Paise
Twelve Only7072
10.07
Providing and fixing floor trap of PVC,110 mm outer dia(multi trap)
including CP cockroach free floor grating with cup etc including cost
and conveyance of all materials, labour charges, sundries etc
complete as directed by the Engineer in charge at all levels
no 17.00 315.32Rupees Three Hundred Fifteen And Paise
Thirty Two Only5360
10.08
Providing and fixing CP Towel rail of approved make including cost
and conveyance of all materials, labour charges, sundries etc
complete as directed by the Engineer in charge at all levels.(The
purchase price considered is Rs 109/-any deviation plus or minus
in the purchase price will be adjusted in the price quoted).
no 10.00 160.28Rupees One Hundred Sixty And Paise
Twenty Eight Only1603
Tenderer 152 ChiefEngineer
-
Sl.No Description Of Items Unit Quantity Rate(Rs) Rate in wordsAmount
(Rs)
10.09
Providing and fixing CP brass health faucets with 8mm dia 1 meter
long flexible tube and wall hook with all fittings and fixtures complete
inlcuding cutting and making good the walls and floors wherever
required including cost and conveyance of all materials, labour
charges, sundries etc complete as directed by the Engineer in charge
at all levels.(The purchase price considered including all
accessories is Rs 532/-any deviation plus or minus in the purchase
price will be adjusted in the price quoted).
no 6.00 693.73Rupees Six Hundred Ninety Three And
Paise Seventy Three Only4162
10.10
Providing and fixing premium quality CP brass overhead shower 4"
and wall flange of approved make and model including cost of all
materials, labour etc., complete as directed by the Engineer-in-charge
at all levels. (The purchase price considered including all accessories
is Rs.284/- including all accessories any deviation plus or minus in the
purchase price will be adjusted in the price quoted)
no 8.00 341.10Rupees Three Hundred Forty One And Paise
Ten Only2729
10.11
Supplying, laying and jointing hard PVC pipes with PVC specials such
as tees, bends, door bend, door tee, elbows,unions, etc. with clamps
including cutting and making good the walls,testing the lines rectifying
any leakages or defects,etc. complete as directed by the Engineer-in-
Charge for soil, waste, rain water,drains, vent pipe, etc. concealed or
open at all levels including cost and conveyance of all materials,
labour charges, sundries etc complete for concealed work as directed
by the Engineer- in-Charge
10.11.01 110mm OD (6 kg/cm2) m 60.00 500.66Rupees Five Hundred And Paise Sixty Six
Only30040
10.11.02 75mm OD(6kg/cm2) m 80.00 337.70Rupees Three Hundred Thirty Seven And
Paise Seventy Only27016
10.11.03 50mm OD(6 kg/cm2) m 40.00 266.91Rupees Two Hundred Sixty Six And Paise
Ninety One Only10676
10.12
Supplying, laying and jointing hard PVC pipes with PVC specials such
as tees, bends, door bend, door tee, elbows,unions, etc. with clamps
including earth work, refilling, ,testing the lines rectifying any leakages
or defects,etc. complete as directed by the Engineer-in-Charge for
soil, waste, rain water,drains, vent pipe, etc. concealed or open at all
levels including cost and conveyance of all materials, labour charges,
sundries etc complete for external works as directed by the Engineer -
in-Charge
Tenderer 153 ChiefEngineer
-
Sl.No Description Of Items Unit Quantity Rate(Rs) Rate in wordsAmount
(Rs)
10.12.01 160mm OD(6 kg/cm2) m 36.00 550.26Rupees Five Hundred Fifty And Paise
Twenty Six Only19809
10.12.02 110mm OD(6 kg/cm2) m 24.00 438.93Rupees Four Hundred Thirty Eight And
Paise Ninety Three Only10534
10.12.03 75mm OD(6 kg/cm2) m 18.00 245.96Rupees Two Hundred Forty Five And Paise
Ninety Six Only4427
10.13Providing and fixing PVC vent cowl to pipe already fixed as directed
by Engineer-in-Charge at all levels.
10.13.01 75 mm dia no 1.00 22.42Rupees Twenty Two And Paise Forty Two
Only22
10.13.02 110 mm dia no 1.00 31.08 Rupees Thirty One And Paise Eight Only 31
10.14
Supplying and fixing soap dish of approved quality and make
including cost and conveyance of all materials labour charges ,lead,
lift, all taxes ,cutting and making good the walls and floors etc
complete etc complete as directed by the Engineer in Charge(The
purchase price considered including all accessories is Rs 163/-any
deviation plus or minus in the purchase price will be adjusted in the
price quoted).
no 10.00 200.55Rupees Two Hundred And Paise Fifty Five
Only2006
TOTAL OF SUB HEAD-10.0 264397
Tenderer 154 ChiefEngineer
-
Sl.No Description Of Items Unit Quantity Rate(Rs) Rate in wordsAmount
(Rs)
(SH: - 11.0 - WATER SUPPLY)
11.01
Supplying, laying, and jointing schedule 40 UPVC ASTM pipe and
Schedule 80 ASTM-UPVC specials of approved make such as tees
elbows, unions,bends,sockets bends,flanges, reducers, end
caps,saddles, plugs,coupling, etc. including cost of all jointing
materials like solvent cement, bolts, nuts, rubber washers,ferrule,pipe
supports, cost of extra wastage of fittings during laying of pipe line
such as rectification and recharging of the existing line as and when
required etc.hire of tools and plant, cost and conveyance of water for
testing after connecting to mains including all testing pipe line to the
specified hydrostatic test pressure,rectifying any leakage or defects
etc. complete.as directed by Engineer-in-Charge for water supply.
11.01.01 100mm dia ID m 6.00 871.05Rupees Eight Hundred Seventy One And
Paise Five Only5226
11.01.02 80 mm dia ID m 6.00 634.37Rupees Six Hundred Thirty Four And Paise
Thirty Seven Only3806
11.01.03 65 mm dia ID m 3.00 479.69Rupees Four Hundred Seventy Nine And
Paise Sixty Nine Only1439
11.01.04 50 mm dia ID m 15.00 314.35Rupees Three Hundred Fourteen And Paise
Thirty Five Only4715
11.01.05 40 mm dia ID m 90.00 223.58Rupees Two Hundred Twenty Three And
Paise Fifty Eight Only20122
11.01.06 32 mm dia ID m 24.00 191.87Rupees One Hundred Ninety One And Paise
Eighty Seven Only4605
11.01.07 25 mm dia ID m 6.00 145.74Rupees One Hundred Forty Five And Paise
Seventy Four Only874
Tenderer 155 ChiefEngineer
-
Sl.No Description Of Items Unit Quantity Rate(Rs) Rate in wordsAmount
(Rs)
11.02
Supplying, laying, jointing and hydrostatically testing ISI marked PVC
pipes as per IS 4985 and specials such as Tees,
elbows,bends,flanges, reducers, end caps,saddles, plugs,coupling,
etc. as per IS 7834 or IS 10124as the case may be including cost of
all jointing materials like solvent cement, bolts, nuts, rubber
washers,ferrule,pipe supports, cost of extra wastage of fittings during
laying of pipe line such as rectification and recharging of the existing
line as and when required etc.hire of tools and plant, cost and
conveyance of water for testing after connecting to mains including all
testing charges,rectifying any leakage or defects, cutting and making
good the walls etc. complete.as directed by Engineer-in-Charge for
concealed lines for water supply.
11.02.01 40 mm OD (10 kg/cm2 ) m 19.00 266.91Rupees Two Hundred Sixty Six And Paise
Ninety One Only5071
11.02.02 32 mm OD (10 kg/cm2 ) m 38.00 238.86Rupees Two Hundred Thirty Eight And Paise
Eighty Six Only9077
11.02.03 25 mm OD (10 kg/cm2 ) m 95.00 225.50Rupees Two Hundred Twenty Five And
Paise Fifty Only21423
11.02.04 20 mm OD (10 kg/cm2 ) m 38.00 220.16Rupees Two Hundred Twenty And Paise
Sixteen Only8366
11.03
Providing and fixing gun metal gate valve with C.I. Wheel of approved
quality (screwed end) including cost and conveyance of all materials,
labour charges, sundries etc complete as directed by the Engineer- in-
Charge at all levels
11.03.01 65 mm dia nominal bore no 2.00 5621.65Rupees Five Thousand Six Hundred Twenty
One And Paise Sixty Five Only11243
11.03.02 40 mm dia nominal bore no 1.00 1157.24Rupees One Thousand One Hundred Fifty
Seven And Paise Twenty Four Only1157
11.03.03 32 mm dia nominal bore no 6.00 786.89Rupees Seven Hundred Eighty Six And
Paise Eighty Nine Only4721
11.03.04 25 mm dia nominal bore no 4.00 599.83Rupees Five Hundred Ninety Nine And Paise
Eighty Three Only2399
Tenderer 156 ChiefEngineer
-
Sl.No Description Of Items Unit Quantity Rate(Rs) Rate in wordsAmount
(Rs)
11.04
Supplying approved make PVC gully trap of size 160 x 110mm and CI
grating 150mmx150mm size and light duty C.I cover with frames
300mmx300mm size(inside) the weight of cover to be not less
than4.5kg and frame to be not less than2.7kg (CI MH cover and frame
as per IS:1726) single sealed of size conveying to size the above
mentioned items and constructing 30cmx30cm internal size gully trap
chamber and depth upto 60cm,115 thk brick wall in CM 1:6 on a foundation of PCC 1:4:8.100mm
thick plastering inside with CM 1:3,12mm thk with a neat cement
flushing coat and conveying to site,cleaning ,installing and testing
approved make PVC gully trap with 160mm outlet (Fabricated),
surrounding with CC 1:1.5:3, 150x150mmm,top with CI grating above
the PVC gulley trap and light duty CI cover and frame over the
chamber including cost of all materials, etc complete as per approved
drawing and as directed by Engineer-in- Charge
11.04.01 supply no 2.00 536.96Rupees Five Hundred Thirty Six And Paise
Ninety Six Only1074
11.04.02 fixing no 2.00 1633.85Rupees One Thousand Six Hundred Thirty
Three And Paise Eighty Five Only3268
11.05
Providing and placing on terrace (at all floor levels) polyethylene water
storage tank ISI:12701 marked indicating the BIS License No. with
cover and suitable locking arrangement and making necessary holes
for inlet, outlet and overflow pipes but without fittings and the base
support for tank including cost and conveyance of all materials, labour
charges, sundries etc complete as directed by the Engineer in charge
in multiple nos wherever required
ltr 1000.00 6.97 Rupees Six And Paise Ninety Seven Only 6970
Tenderer 157 ChiefEngineer
-
Sl.No Description Of Items Unit Quantity Rate(Rs) Rate in wordsAmount
(Rs)
11.06
Constructing brick masonry manhole with 75 class designation bricks
in cement mortar 1:4 (1 Cement : 4 coarse sand) R.C.C. top slab with
1:2:4 (1 Cement : 2 coarse sand : 4 graded stone aggregate 20 mm
nominal size) foundation concrete with 1:4:8 mix (1 Cement : 4 coarse
sand : 8 graded stone aggregate 40 mm nominal size) inside
plastering 12 mm thick with cement mortar 1:3 (1 Cement : 3 coarse
sand) finished with floating coat of neat cement and making channels
in cement concrete 1:2:4 (1 Cement : 2 coarse sand : 4 graded stone
aggregate 20 mm nominal size) finished with a floating coat of neat
cement complete as per standard design including cost and
conveyance of all materials, labour charges, sundries etc complete as
directed by the Engineer-in-Charge
11.06.01
Inside size 90x80 cm and 45 cm deep including C.I. cover with frame
(light duty) 455x610 mm internal dimensions total weight of cover and
frame to be not less than 38 kg (weight of cover 23 kg and weight of
frame 15 kg) :
With bricks.Class designation 75 no 5.00 10209.69Rupees Ten Thousand Two Hundred Nine
And Paise Sixty Nine Only51048
11.07
Providing and constructing soak pit 1.5 m x 1.5 m x 1.5 m size with
honey comb brick work on the sides upto a height of 0.9m and brick
masonry in CM 1:6 for the balance height,providing and filling brick
bats graded, upto a height of 1.2 m,providing and laying precast slab
over the pit supporting on the brick work, including cost and
conveyance of all materials,labour charges, lead, lift, etc. complete
as directed by the Engineer-in-charge.
no 2.00 23541.45
Rupees Twenty Three Thousand Five
Hundred Forty One And Paise Forty Five
Only
47083
11.07.01Supplying and fixing of CI double flanged wall casting pipe with
puddle, 0.6m length
11.07.01.01 80mm no 2.00 2931.34Rupees Two Thousand Nine Hundred Thirty
One And Paise Thirty Four Only5863
11.07.01.02 100mm no 2.00 3449.66Rupees Three Thousand Four Hundred
Forty Nine And Paise Sixty Six Only6899
11.08Supplying and fixing of CI single flanged wall casting pipe with
puddle, 0.6m length
Tenderer 158 ChiefEngineer
-
Sl.No Description Of Items Unit Quantity Rate(Rs) Rate in wordsAmount
(Rs)
80mm no 2.00 2620.34Rupees Two Thousand Six Hundred Twenty
And Paise Thirty Four Only5241
11.09
Supplying and fixing CI foot valve with all accessories including cost
and conveyance of all materials,labour charges etc complete as
directed by the Engineer -in - charge at all levels.
40mm no 2.00 858.32Rupees Eight Hundred Fifty Eight And Paise
Thirty Two Only1717
11.10
Supplying and fixing gun metal Non return valve with all accessories
including cost and conveyance of all materials,labour charges etc
complete as directed by the Engineer- in-Charge at all levels
11.10.01 32mm nominal bore no 2.00 1557.43Rupees One Thousand Five Hundred Fifty
Seven And Paise Forty Three Only3115
11.10.02 40mm nominal bore no 1.00 2155.46Rupees Two Thousand One Hundred Fifty
Five And Paise Forty Six Only2155
11.11 Supplying and fixing of centrifugal pump, with CI construction, CI
impeller complete with motor, base plate, foundation bolts, nuts,
pressure guage and all accessories. and working with 230V, single
phase and 50 Hz frequency
Capacity :7m3/hr
Head : 16m no 2.00 9683.00Rupees Nine Thousand Six Hundred Eighty
Three Only19366
TOTAL OF SUB HEAD-11.0 258045
Tenderer 159 ChiefEngineer
-
Sl.No Description Of Items Unit Quantity Rate(Rs) Rate in wordsAmount
(Rs)
(SH: - 12.0 - MISCELLANEOUS BUILDING WORK)
12.01
Providing and applying acrylic reinforced cementitious waterproof
coating Masterseal 550 EL, in two coats to achieve 1mm thickness
Concrete surfaces should be free of dust, oil and other contaminants.
All high spots should be removed. Moss and lichen must be removed
physically. After treatment wash down thoroughly with clean water and
allow to dry. Prewetting the surface before applying the water proofing
material. The rate shall including cost and conveyance of all materials,
all labour charges, all taxes, lead, lift, sundries, etc., etc complete as
directed by the Engineer -in-Charge
sqm 51.00 476.22Rupees Four Hundred Seventy Six And
Paise Twenty Two Only24287
12.02 Side boundary fencing work with PVC coated chain linkfencing in 2m height including all charges for providing 40mm GI pipes @2.70 meters c/c as verticals fixed to groundusing PCC , other horizontal members with 25 mm dia GIpipe at top, bottom and at middle (total 3 numbers), fixingthe chain link in the frame work, with provision for onenumber of door on either short sides with provision for lock sqm 800.00 800.00 Rupees Eight Hundred Only 640000& key arrangements.
12.03 Providing and fixing pre engineered structures over the foundation already supplied according to approved designs and elevation Required primary and secondary steel sections to be suppplied anderected with necessary roof and wall panels (60mm panels)providing necessary provisions for doors and windows. All the steelsections to be painted with one coat of primer and two coats ofenamel paint. The rate to include cost of all materials, labour, lead,
lift, fabrication and erection charges etc complete sqm 180.00 4843.80 Rupees Four Thousand Eight Hundred Forty
Three And Paise Eighty Only
871884
TOTAL OF SUB HEAD-12.0 1536171
GRAND TOTAL 24248338
Tenderer 160 ChiefEngineer
-
Item.
No.Description of Items Unit Qty Rate(Rs) Rate in Words
Amount
(Rs)
PART A
1.0 LT PANEL BOARD AND ACCESSORIES
Supply, installation, testing and commissioning of Energy meter box
of cubicle construction made from 1.6mm CRCA sheet suitable for
accommodating one number of three phase Electronic Energy meter (
supply of energy meter is under KSEB scope) and 3 nos.63A HRC
fuse and neutral link ,3 nos of 2A SP MCB ,inter connections ,
providing necessary supports made from the same gauge CRCA sheet
to fix energy meters, etc .The cubicle shall be provided with hinged
door construction and vision panel for the meter
compartment.Suitable knock out for cable entry and exit shall be
provided.The entire board shall be painted with 2 coats of synthetic
enamel paint over a coat of zinc chromate primer etc as required
including fixing it on wall, making good the damages colour washing
etc. as required. CRCA sheet alone be used for the fabrication.
Angles/ flats/ slotted angles etc shall not be used for the fabrication of
main housing of meter board.
no 1 6170.00 Rupees Six Thousand One Hundred Seventy Only 6170.00
1.2 MSB
Supply, installation, testing and commissioning of totally enclosed
free standing floor mounting dust and vermin proof indoor cubicle
type Main Switch Board (MSB) suitable for 415 V, 3 phase, 50 HZ
supply, fabricated of 14 SWG CRCA sheet steel Powder coated
complete with busbars having 125 A rating, indicating lamps (LED
type) with 2A control MCBs, CT's, connections & interconnections
with suitable size of copper leads/solid aluminium strips/rod and
having following incoming and outgoing MCCBs as per the drawing
and specifications(Refer particular specification and Drawing).
Incomer
KITCO LTDNATIONAL GAMES SECRETARIAT
Construction of Municipal Stadium at Chengannur
SPECIFCATION AND SCHEDULE OF QUANTITIES-PART B- ELECTRICAL WORKS
tenderer 161 Chief Engineer
-
Item.
No.Description of Items Unit Qty Rate(Rs) Rate in Words
Amount
(Rs)
125A, Four Pole Switch disconnector fuse unit (SDFU) AC 23A
complete with all accessories including handle, 3nos 125A Din type
HRC fuse unit, neutral link etc. - 1No.
125A TPN busbar chamber with Aluminium busbar
RYB Indicating lamps LED type -3Nos.
Digital Voltmeter - 1 set
Digital Ammeter - 1 set
Outgoing
63A, TPN Switch disconnector fuse unit (SDFU) AC 23A complete
with all accessories including handle, 3nos 63A Din type HRC fuse
unit, neutral link etc. -2Nos.
32A, TPN Switch disconnector fuse unit (SDFU) AC 23A complete
with all accessories including handle, 3nos 32A Din type HRC fuse
unit, neutral link etc. - 4Nos.
no 1 89210.00 Rupees Eighty Nine Thousand Two Hundred Ten Only 89210.00
TOTAL(SUB PART A) 95380.00
PART B
2.0 WIRING AND ACCESSORIES
2.1
Supply & wiring for following points in surface/recessed mounted
rigid medium gauge 20mm PVC conduit with all accessories, using 3
runs of 1.5 sqmm FRLS PVCinsulated stranded copper conductor
single core wire for phase, neutral & earth, with modular 6A one way
switch, modular front plate, suitable GI box, ceiling rose etc
asrequired. The total distance from the switch box to the point will
not exceed 5mtr, incase if length increases above 5 metres, the wiring
shall be measured under item 2.4
Light point/ exhaust fan point/call bell point no 60.00 1170.00 Rupees One Thousand One Hundred Seventy Only 70200.00
2.2
Copper plug point wiring - Wiring for power plug with 2x4 sq. mm.,
PVC insulated, copper conductor, stranded cable (FRLS) along
with 1x2.5 sq. mm., PVC insulated, copper conductor, stranded cable
for loop earthing in surface/recessed PVC conduit etc.as required
complete.
m 40.00 272.00 Rupees Two Hundred Seventy Two Only 10880.00
tenderer 162 Chief Engineer
-
Item.
No.Description of Items Unit Qty Rate(Rs) Rate in Words
Amount
(Rs)
2.3
Copper circuit wiring - Wiring for circuit with 2x2.5 sq. mm., PVC
insulated, copper conductor, stranded cable along with 1x1.5 sq.
mm., PVC insulated, copper conductor, stranded cable for loop
earthing in surface/recessed pvc conduit etc.as required complete.
m 170.00 222.00 Rupees Two Hundred Twenty Two Only 37740.00
2.4
Copper circuit wiring - Wiring for circuit wiring with 2x1.5 sq.
mm., PVC insulated, copper conductor, stranded cable (FRLS) along
with 1x1.5 sq. mm., PVC insulated, copper conductor, stranded cable
for loop earthing in surface/recessed PVC conduit etc. as required
complete.
m 150.00 202.00 Rupees Two Hundred Two Only 30300.00
2.5
Group controlled light point with 1.5 sq. mm wire - Wiring for Group
controlled light point (from one point to another point) with 1.5 sq.
mm PVC insulated, (FRLS), copper conductor cable along with
1x1.5 sq. mm., PVC insulated, copper conductor, stranded cable for
loop earthing in surface / recessed PVC conduit. Note:- This item
does not include the cost of MCB or 16Amp/ 6Amp one way
switches. The total distance from one point to another point will not
exceed 5meters. In case if the total length increases 5meters, the
additional lengtth shall be measured under item 2.4. The distance
from DB to 1st point will be measured under item circuit wiring.
no 2.00 1047.00 Rupees One Thousand Forty Seven Only 2094.00
2.6
Supply and fixing suitable size GI box with modular front plate and
cover on surface or in recess, including providing and fixing 2/3 pin
combined 6A modular socket outlet and 6 A modular switch with
connection etc as required.
no 9.00 464.00 Rupees Four Hundred Sixty Four Only 4176.00
2.7
Supply and fixing of 3nos of 6A socket & 2no switch with non
metallic inner and outer cover/plate in surface/recess including
providing and fixing suitable size metal box, inter connections etc as
required.
no 3.00 895.00 Rupees Eight Hundred Ninety Five Only 2685.00
tenderer 163 Chief Engineer
-
Item.
No.Description of Items Unit Qty Rate(Rs) Rate in Words
Amount
(Rs)
2.8
Supply & fixing suitable size GI box with modular front plate and
cover on surface or in recess, including providing & fixing of 16A
modular switch with connection etc as required.
no 1.00 367.00 Rupees Three Hundred Sixty Seven Only 367.00
2.9
Supply & fixing suitable size GI box with modular front plate and
cover on surface or in recess, including providing and fixing of 3pin
16A modular socket outlet with connection etc as required.
no 1.00 440.00 Rupees Four Hundred Forty Only 440.00
2.10
Supply & fixing of following rigid medium gauge PVC conduit along
with all accessories in surface/recess including cutting the wall and
making good the same in case of recess mounting as required.
2.10.1 20 mm m 30.00 114.00 Rupees One Hundred Fourteen Only 3420.00
2.10.2 25 mm m 30.00 124.00 Rupees One Hundred Twenty Four Only 3720.00
SUB TOTAL (PARTB) 166022.00
PART C
3.0 MCBs AND MCB DISTRIBUTION BOARDS
3.1
Supply and installation of sheet steel, phosphatised and painted, dust
and vermin proof enclosure of MCB DB including copper/brass bus
bar, neutral link, earth bus and DIN rail suitable for fixing
MCB/isolator etc. fixed on wall using suitable anchor bolts or fixed in
recess including cutting hole on the wall, making good the damages,
colour washing etc. as required.
3.1.1
4 way (8+12 ) - double cover TPN vertical DB with provision for
fixing Isolator /RCBO as incomer and SP/TP MCB as outgoing
(IP42/43) Note: There should be facilty to terminate incoming cables
of size upto 35 sq.mm AYFY and outgoing cables of size upto 4x16
sq.mm AYFY.
no 1.00 4855.00 Rupees Four Thousand Eight Hundred Fifty Five Only 4855.00
tenderer 164 Chief Engineer
-
Item.
No.Description of Items Unit Qty Rate(Rs) Rate in Words
Amount
(Rs)
3.1.2
6 way (8+18 ) - double cover TPN vertical DB with provision for
fixing Isolator /RCBO as incomer and SP/TP MCB as outgoing (IP54)
Note: There should be facilty to terminate incoming cables of size
upto 35 sq.mm AYFY and outgoing cables of size upto 4x16 sq mm
AYFY cable.
no 1.00 10358.00 Rupees Ten Thousand Three Hundred Fifty Eight Only 10358.00
3.1.3 6 way (8+18) -three phase double cover horizontal (IP 42/43) no 1.00 2824.00 Rupees Two Thousand Eight Hundred Twenty Four Only 2824.00
3.1.4 8 way (8+24) -three phase double cover horizontal (IP 42/43) no 1.00 3455.00 Rupees Three Thousand Four Hundred Fifty Five Only 3455.00
3.2 DP enclosure for independent mounting of MCB no 1.00 310.00 Rupees Three Hundred Ten Only 310.00
3.3
Supply and fixing of following rating residual current circuit breaker
having earth leakage protection (RCCB+MCB) as per specification
as required3.3.1 4 pole 32 amps. (415 Volts), 100mA sensitivity. no 3.00 3707.00 Rupees Three Thousand Seven Hundred Seven Only 11121.00
3.3.2 4 pole 32 amps. (415 Volts), 30mA sensitivity. no 1.00 3781.00 Rupees Three Thousand Seven Hundred Eighty One Only 3781.00
3.4Supply and fixing of following rating, 10 KA, Miniature circuit
breakers of the following serie in the existing enclosure as required.
3.4.1 6A to 32A TP MCB, B/C-CURVE MCB no 4.00 846.00 Rupees Eight Hundred Forty Six Only 3384.00
3.4.2 6A to 32A SP MCB, B/C-CURVE MCB no 15.00 213.00 Rupees Two Hundred Thirteen Only 3195.00
3.4.3 6A to 32A FP MCB, B/C-CURVE MCB no 2.00 1192.00 Rupees One Thousand One Hundred Ninety Two Only 2384.00
3.5Supply and fixing of following rating, 10 KA, Miniature circuit
breakers of the following series etc. as required.
Supply and fixing of SP MCB blanking plate no 4.00 25.00 Rupees Twenty Five Only 100.00
3.6Supply and fixing cable end boxes for the following types of DB with
necessary bolts and nuts etc. as required .
3.6.1 Suitable for all types of vertical DB no 1.00 916.00 Rupees Nine Hundred Sixteen Only 916.00
3.6.2 Suitable for IP 43, 6way, TPN DB no 1.00 1219.00 Rupees One Thousand Two Hundred Nineteen Only 1219.00
SUB TOTAL (PART C) 47902.00
tenderer 165 Chief Engineer
-
Item.
No.Description of Items Unit Qty Rate(Rs) Rate in Words
Amount
(Rs)PART D
4.0 LIGHT FIXTURES AND FANS
4.1
Supply of 1x28W surface mounted decorative fluorescent lamp
fixture with T5 electronic batten, including 28W T5 lamp,prewired
complete with all necessary accessories as required (Sample shall be
aprroved by the engineer in charge)
no 27.00 630.00 Rupees Six Hundred Thirty Only 17010.00
4.2
Supply of 1x14W surface mounted decorative fluorescent lamp
fixture with T5 electronic batten, including 14W T5 lamp,prewired
complete with all necessary accessories as required (Sample shall be
aprroved by the engineer in charge)
no 16.00 540.00 Rupees Five Hundred Forty Only 8640.00
4.3
Supply of CFL bulk head light with 1x9W CFL lamp including all
accessories for mounting on the existing PVC junction box (Make :
Wipro WKP 14109 or equivalent approved make)
no 6.00 1200.00 Rupees One Thousand Two Hundred Only 7200.00
4.4
Supply, Instalation,Testing and Commissioning of Hot dip galvanised
MS tubular swaged pole of total length 8.5m fabricated with
following dia pipes 114.3x4.5 (Bottom), 88.9X4.05(middle),
76.1x3.25(top) and sectional length of (4+1.5+3) with a bottom plate
of size 300x300x6mm with (single bracket)swan neck including
bending to shape the top pipe section with over hang of 1.5 m,erecting
the same in cement concrete foundation( as required by the soil
bearing capacity) including supply and fixing 1no street light
luminaire with MH lamp 1 X 150W MH (IP 65) luminaire and
lamp,as required complete with IP 65 protection. (Sample shall be
approved by the Engineer- in-Charge)
no 14.00 31075.00 Rupees Thirty One Thousand Seventy Five Only 435050.00
tenderer 166 Chief Engineer
-
Item.
No.Description of Items Unit Qty Rate(Rs) Rate in Words
Amount
(Rs)
4.5
Supply, Instalation,Testing and Commissioning of Hot dip galvanised
MS tubular swaged pole of total length 8.5m fabricated with
following dia pipes 114.3x4.5 (Bottom), 88.9X4.05(middle),
76.1x3.25(top) and sectional length of (4+1.5+3) with a bottom plate
of size 300x300x6mm with (double bracket)swan neck including
bending to shape the top pipe section with over hang of 1.5 m,erecting
the same in cement concrete foundation( as required by the soil
bearing capacity) including supply and fixing 2no street light
luminaire with MH lamp 1 X 150W MH (IP 65) luminaire and
lamp,as required complete with IP 65 protection. (Sample shall be
approved by the Engineer-in-Charge)
no 3.00 32201.00 Rupees Thirty Two Thousand Two hundred and One Only 96603.00
4.6
Supply, of the following sizes of exhaust fans in the existing opening,
fixing necessary bolt and nuts, making good the damages etc. as
required including giving connections with required length of
24/0.20mm PVC insulated and PVC sheathed 3 core round copper
conductor flex wire conforming to relevant ISS (Sample shall be
aprroved by the Engineer-in-Charge)
250mm, single phase, light duty exhaust fan in plastic body with self
opening louversno 8.00 1338.00 Rupees One Thousand Three Hundred Thirty Eight Only 10704.00
4.7
Supply of ceiling fan, with double ball bearing, Aluminium pressure
die cast body with Aluminium blades, canopies, hanging shackle, 30
cm down rod and without speed regulator suitable for 230 V/240 V 50
HZ, AC supply confirms to IS 374/1979 as required complete.
(Sample shall be aprroved by the Engineer in charge)
1200mm sweep no 3.00 1734.00 Rupees One Thousand Seven Hundred Thirty Four Only 5202.00
4.8
Installation, testing and commissioning of ceiling fan wiring the
down rod of standard length (upto 30cm) with 1.5 sq.mm PVC
insulated copper conductor single core cable including earthing the
regulator etc. as required.
no 3.00 136.00 Rupees One Hundred Thirty Six Only 408.00
tenderer 167 Chief Engineer
-
Item.
No.Description of Items Unit Qty Rate(Rs) Rate in Words
Amount
(Rs)
4.9
Supply and providing every additional length of down rod of suitable
size heavy guage GI/WI pipe with 16/0.20mm PVC insulated and
PVC sheathed 3 core round copper conductor flex wire conforming in
relevant ISS or with original wiring extended including painting as
required. (for extending the length of down rod for ceiling fan)
no 5.00 17.00 Rupees Seventeen Only 85.00
4.10
Installation, testing and commissioning of exhaust fan upto 450mm
sweep in the existing opening, including making the hole to suit the
size of the above fan, making good the damage, connections, testing
& commissioning etc as required.
no 8.00 675.00 Rupees Six Hundred Seventy Five Only 5400.00
4.11
Installation, testing and commissioning of prewired flourescent fitting
of all types complete with all accessories and fluorescent lamps of all
types directly on wall and giving connections with 16/0.20 mm 3 core
PVC insulated and sheatherd round copper conductor flex wire or
extending the original wiring and giving connections as required.
no 49.00 127.00 Rupees One Hundred Twenty Seven Only 6223.00
4.12
Supply and fixing of 2 module type, 5 speed electronic fan regulator
120watts rating with non metallic front plate including providing and
fixing suitable size metal box in surface/ recess with all necessary
accessories as required.
no 3.00 532.00 Rupees Five Hundred Thirty Two Only 1596.00
4.13 Numbering of ceiling fan / exhaust fan/ fluorescent fitting as required. no 68.00 29.00 Rupees Twenty Nine Only 1972.00
SUB TOTAL (PART D) 596093.00
PART E
5.0 CABLES AND CABLING
5.1 LT CABLING
Supply of following size 1.1 KV grade XLPE insulated, PVC
sheathed, armoured Aluminium /copper conductor cable conforming
to IS 7098 (Part 1) amended upto date.
5.1.1 3.5C 70 Sq.mm Al m 30.00 442.00 Rupees Four Hundred Forty Two Only 13260.00
tenderer 168 Chief Engineer
-
Item.
No.Description of Items Unit Qty Rate(Rs) Rate in Words
Amount
(Rs)5.1.2 4C 16 Sq.mm Al m 45.00 176.00 Rupees One Hundred Seventy Six Only 7920.00
5.1.3 4C 10 Sq.mm Al m 80.00 141.00 Rupees One Hundred Forty One Only 11280.00
5.1.4 4C 4 Sq.mm Al m 1020.00 116.00 Rupees One Hundred Sixteen Only 118320.00
5.1.5 3C 4 Sq.mm Al m 15.00 95.00 Rupees Ninety Five Only 1425.00
5.2
Supplying and making end termination with brass compression gland
and aluminium/Copper lugs for following size of XLPE insulated
PVC sheathed aluminium/copper conductor cable of 1.1 kV grade as
required.
5.2.1 3.5C 70 Sq mm Al no 2.00 477.00 Rupees Four Hundred Seventy Seven Only 954.00
5.2.2 4C 16 Sq.mm Al no 2.00 347.00 Rupees Three Hundred Forty Seven Only 694.00
5.2.3 4C 10 Sq.mm Al no 6.00 312.00 Rupees Three Hundred Twelve Only 1872.00
5.2.4 4C 4 Sq.mm Al no 32.00 279.00 Rupees Two Hundred Seventy Nine Only 8928.00
5.2.5 3C 4 Sq.mm Al no 2.00 277.00 Rupees Two Hundred Seventy Seven Only 554.00
5.3
Laying & fixing of one no. XLPE insulated & PVC sheathed power or
control cable of 1.1kV grade of following size in recess/ surface/
cable tray/ wall with saddles, clamps and all other accessories as
required
5.3.1 Cable size not exceeding 25Sq mm m 60.00 95.00 Rupees Ninety Five Only 5700.00
5.3.2 Above 25 Sq.mm upto 120 Sq.mm m 20.00 145.00 Rupees One Hundred Forty Five Only 2900.00
5.4
Laying of one number PVC insulated and PVC sheathed armoured
power cable of 1.1kV grade fo the following sizes in ground including
excavation of trench of size 35x75cm, sand cushioning up to a height
of 25cm (8cm+17cm), providing protective covering with country
burnt bricks laid breadth wise, refilling the trench etc. as required
5.4.1 Cable size not exceeding 25Sq mm m 1020.00 234.00 Rupees Two Hundred Thirty Four Only 238680.00
5.4.2 Above 25 Sq.mm upto 120 Sq.mm m 5.00 251.00 Rupees Two Hundred Fifty One Only 1255.00
tenderer 169 Chief Engineer
-
Item.
No.Description of Items Unit Qty Rate(Rs) Rate in Words
Amount
(Rs)
5.5
Laying of one number additional PVC insulated and PVC sheathed
armoured power cable of 1.1KV grade of the following sizes in
ground in the same trench in one tier horizontal formation including
widening the trench by 20 cm,sand cushioning up to the height of 25
cm,providing protective covering with country burnt bricks laid
breadth wise, refilling the trench etc. as required
Upto 25 Sq.mm m 40.00 149.00 Rupees One Hundred Forty Nine Only 5960.00
5.6
Laying of one number PVC insulated and PVC sheathed armoured
power cable of 1.1kV grade fo the following sizes in the existing
RCC/HUME/STONEWARE/GI/DWC pipe as required
5.6.1 Upto 25 sq.mm m 35.00 45.00 Rupees Forty Five Only 1575.00
5.7
Laying of one number PVC insualted and PVC sheathed armoured
power cable of 1.1KV grade of the following sizes in the existing
masonry open duct as required.
5.7.1 Cable size not exceeding 25Sq mm m 5.00 36.00 Rupees Thirty Six Only 180.00
5.7.2 Above 25 Sq.mm upto 400 Sq.mm m 5.00 49.00 Rupees Forty Nine Only 245.00
5.8
Supply, fabricating and installing MS items such as Tees/ angles/
channels etc. on floor/ ceiling/ wall including necessary civil work
such as grouting, finishing etc. and painting with two coats of primer
and two coats of synthetic enamel paint as required
kg 25.00 95.00 Rupees Ninety Five Only 2375.00
5.9
Supplying, threading, laying and jointing of the following sizes of 'B'
class GI pipe with all required accessories in ground in the existing
trench as protective covering to earth leads.
5.9.1 40 mm m 25.00 259.00 Rupees Two Hundred Fifty Nine Only 6475.00
5.9.2 50 mm m 10.00 304.00 Rupees Three Hundred Four Only 3040.00
SUB TOTAL PART -E 433592.00
PART F
tenderer 170 Chief Engineer
-
Item.
No.Description of Items Unit Qty Rate(Rs) Rate in Words
Amount
(Rs)6.0 EARTHING AND SAFETY EQUIPMENTS
6.1
Supply and providing ISI pipe earthing as per IS 3043 with 2.5 meter
long 40mm dia B class GI pipe with 12mm dia holes, providing GI
funnel with weld mesh, fixing GI strip of size50x6mm with min.
length of 20cm clamped with 50x5mm GI flat using 12x10mm GI bolt
& nut at top of the GI pipe as test joint, filling around the GI pipe at a
radius of 15cm with a homogeneous of charcoal, & sieved earth upto
a height of 2.0 meter from the bottom, filling the rest of the portion
with excavated soil including watering and ramming providing brick
work (20cm) masonry at top in 1:6 cm cement mortar,plastering the
inside and top of the manhole with 12mm thick 1:6 cement mortar
and providing 300x300x6mm CI covering at the top.
set 4.00 5635.00 Rupees Five Thousand Six Hundred Thirty Five Only 22540.00
6.2
Supplying and laying following GI or copper strip / wire at 0.6m
below ground level including excavation and refilling or on surface
with mounting saddles for conductor earth electrode including
welding etc as required.
6.2.1 25x3 mm copper strip tinned at the points of contacts m 30.00 476.00 Rupees Four Hundred Seventy Six Only 14280.00
6.2.2 3.15mm copper conductor (10 SWG) m 100.00 83.00 Rupees Eighty Three Only 8300.00
6.2.3 4 mm copper conductor (8 SWG) m 1470.00 34.00 Rupees Thirty Four Only 49980.00
SUB TOTAL PART F 95100.00
GRAND TOTAL 1434089.00
tenderer 171 Chief Engineer
-
Description
Part A -Civil Works
Part B- Electrical Works
Total Value of Market rate
items
GRAND TOTAL
I/We agree to carry out the work at par with estimate (1).at estimate rate
(2)........% below the estimate (in figure & words)
...
(3)....% above the estimate (in figure & words) less cost of market rate item
** Tender excess / Deduction will not be applicable for market rate items in the schedule of contract
Signature of Contractor
Witness
Name..
Address.
NATIONAL GAMES SECRETARIAT
Construction of Municipal Stadium at Chengannur
Tender Schedule
Amount (Rs.)
24248338
25682427
23365258
2317169
Total Value of PWD schedule items
1434089
Rupees Two Crore Fifty Six Lakhs Eighty Two Thousand Four Hundred Twenty Seven Only
Tenderer 172 Chief Engineer
-
N
E
S
WGeotech
22.0 21.05.6
7.9
19.7
23.6
9.3
14.611.4
16.5
13.0 7.9
6.99.9
21.111.6
1.47.5
11.3
5.3
7.915.8
5.04.8
24.1
40.6
0.8
16.2
15.3
9.2
11.9
14.2
21.6
18.9
45.5
22.0
15.6
4.1
37.3
5.1
6.3
0.2
15.7
14.7
3.45.1
2.9
2.22.8
9.6
12.2
10.8
11.0
20.4
2.0
22.1
15.4
11.62.5
8.5
7.1
17.4
8.7
12.6
3.7
20.3
26.9
163.0
ROAD
Culvert
ROADGATE FROM THEATRECOMPLEX TO PARKING
ROAD 8M WIDE TO
PROPOSED MULTIPLEX
30.5
5.6
22.6
1.816.12.912.3
5.0
4.505.50
12.50
22.49
36.60
MULTISPORTFACILITYFOR:BADMINTON(4 COURTS)NET BALLBASKET BALLVOLLEYBALL
19.25
36.60
SWIMMING POOL
25M X 12.5 MFOR TRAININGANDCOMPETITIONS
GATE FOR ENTRY TO MULTISPORTSTADIUM AND FUTURE 400M TRACKAND FIELD
MAIN ENTRANCE TO MULTISPORT COMPLEX AND POOL
CAR PARKING AREA
CAR PARKING AREA
DRIVEWAY
DRIVEWAY
THEATRE COMPLEX OR4 SCREEN MULTIPLEX
SEATING 140 PAX PER SCREENTOTAL 560 PAX
200 PAX FOOD COURT BELOW MULTIPLEX
PHASE 2FOOTBALL FIELD W
ITHPROPOSED 8 LANE 400M TRACK
MAIN ENTRANCE TOPROPOSED ATHLETIC TRACKAND FOOTBALL FIELD
PROPOSED WESTERN PAVILLIONPHASE 3
CAR PARKING AREA
CAR PARKING AREA
CAR PARKING AREA
GATE FOR ENTRY TO MULTISPORTSTADIUM AND FUTURE 400M TRACKAND FIELD
PROPOSED EASTERN PAVILLIONPHASE 2
NOTE:
1.A
LL DIM
EN
SIO
NS
AR
E IN
MILLIM
ETE
RS AN
D LEVELS AR
E IN M
ETERS
2.O
NLY
WR
ITTEN
DIM
EN
SIO
NS SH
OU
LD BE FO
LLOW
ED
A B C D E F G H
4 4
32
1
32
18
76
512
1110
9
G HFED
76
58
PUTH
IYA
RO
AD
- NH
BY
PASS, K
OCH
I - 28
KIT
CO
Ltd.(Estd. in 1972 by ID
BI &
Govt. of K
erala)
DR
G N
O:
TITLE:
PR
OJE
CT:
CLIEN
T:
SH
EET N
O:
REV.
DE
SIG
NED
CH
EC
KED
DA
TE
UN
IT
AP
PR
OVED
CH
EC
KED
SC
ALE
DR
AW
N
DATE
INITIAL
PAR
TICU
LAR
SS
L.No.
SPO
RTS & YO
UTH
AFFAIR
S DE
PAR
TMEN
T -N
ATION
AL G
AM
ES SE
CR
ETARIAT
DEV
ELOP
ME
NT O
F CH
ENG
AN
NU
R STAD
IUM
MAS
TER
PLAN
DP
645 DR
G C
L 06 0011 O
F 1
04.05.13
N.T.S
mm
.
38/324, 325, First Floor, Pulikkal B
ldgs
PH
: 0484 2323505, Tele FAX
: 2315505C
OC
HIN
, KE
RA
LA 682016
KA
RS
HA
KA
RO
AD
, near South O
verbridge
Em
ail:waterandenvironm
entgtcs@gm
ail.com
ADMINISTRATIVE AND CHANGE ROOMS
4.96
36.02
-
M S B
CL: 17.2kW
1Rx3.5x70m
m XLPE C
able
63/5AC
L: 110VA
METER
BO
ARD
CU
TOU
T63A
NL
FUSES
KSEB
2A
CO
NN
EC
TED
LOAD
(kW)
DES
CR
IPTIO
N O
F LOAD
LENG
TH IN
METER
S
No. O
F CO
RES
No. O
F RU
NS
PO
WER
CAB
LE (m
m) Al.
EAR
THIN
G (G
I)
FRO
M KSEB
4.810412010
4.510413010
A(0-125A)
2A(0-500V)
VV
SS
125/5AC
L: 15V
AA
A125A TP
N AL B
US
BAR
- PH
&N
DF : 1.5
125ATPN
120A
SD
FU
32ATPN
25A
SD
FU
32ATPN
25A
SD
FU
63ATPNS
DFU
63ATPNS
DFU
CH
AN
GE
RO
OM
32ATPN
25A
SD
FU
1.510413010
EXTER
NAL
32ATPN
25A
SD
FU
PU
MPS
SPAR
ES
PARE
DR
AW
N
CH
EC
KE
D
DE
SIG
NE
D
CH
EC
KE
D
UN
IT
DA
TE
SC
ALE
AP
PR
OV
ED
TITLE:
CLIE
NT:
PR
OJE
CT:
RE
V.
SH
EE
T NO
:D
RG
NO
:
PUTH
IYA
RO
AD
- NH
BY
PASS, K
OC
HI - 28
(Estd. in 1972 by IDB
I & G
ovt. of Kerala)
KIT
CO
Ltd.
SP
OR
TS &
YO
UTH
AFFA
IRS
DE
PA
RTM
EN
T -N
ATIO
NA
L GA
ME
S S
EC
RA
TAR
IATE
AT C
HE
NG
AN
NO
OR
PO
WER
DIS
TRIB
UTIO
N D
IAGR
AMD
P 645 D
RG
EL 06 0011 O
F 1
01.02.13
mm
.
N.T.S
kWH
36W
LDB
36W
VDB
LIGH
TING
34W
VDB
NEU
TRAL LIN
KN
L
CU
T OU
T FUSE
MC
B
SW
ITCH
DIS
CO
NN
ECTO
RFU
SE U
NIT
VO
LT ME
TER
VO
LT ME
TER
AM
ME
TER
KILO WATT HOUR METER
kWH
AVVSSS
ELECTO
R SW
ITCH
SPAR
E
-
SPO
RTS & YO
UTH
AFFAIR
S DEPAR
TMEN
TN
ATION
AL G
AM
ES SE
CR
ETARIAT
DEV
ELOP
ME
NT O
F CH
ENG
AN
NU
R S
TAD
IUM
PLA
N AN
D ELEV
ATION
- CH
AN
GE R
OO
M A
ND
AD
MIN
. BLOC
K -
DP
645 DR
G C
L 061 O
F 108.05.2013
1 : 100m
m.
NO
TE:
1. ALL D
IME
NS
ION
S A
RE
IN M
ILLIME
TER
S A
ND
LEV
ELS
AR
E IN
ME
TER
S2. O
NLY
WR
ITTEN
DIM
EN
SIO
NS
SH
OU
LD B
E FO
LLOW
ED
BA
TH
UR
INA
LTO
I.TO
I.
BA
THB
ATH
BA
THLO
CK
ER
S
LOC
KE
RS
WA
SH
TEA
M M
AN
AG
ER
NO
.1A
DM
IN. O
FFICE
BA
TH
TOI.
TOI.
BA
THB
ATH
BA
THLO
CK
ER
S
LOC
KE
RS
WA
SH
TEA
M M
AN
AG
ER
NO
.2TO
I.TO
I.
LOB
BY
18501200
12002480
45004200
40004200
45001200
12001200
12001850
36020
1700
1530
3000
1680
1450
4760
1700
ELE
VA
TION
PLAN
( Plinth A
rea: 179.00 Sq.m
)
FOR
TEND
ER PU
RPO
SE
-
BATH
UR
INAL
TOI.
TOI.
BATH
BATH
BATH
LOC
KER
S
LOC
KER
S
WA
SH
TEAM
MA
NAG
ERN
O.1
AD
MIN
. OFFIC
E
BATH
TOI.
TOI.
BATH
BATH
BATH
LOC
KER
S
LOC
KER
S
WA
SH
TEAM
MA
NAG
ERN
O.2
TOI.
TOI.
LOB
BY
18501200
12002480
45004200
40004200
45001200
12001200
12001850
36020
4760
SYMBOLDESCRIPTION
SL.NO.
179
SWITCH BOARD
6A SWITCH SOCKET
16A SWITCH SOCKET
300mm SWEEP EXHAUST FAN W
ITH LOUVER
10
LEGEN
D
NOTATION
L2P SPP EF
COMPUTER POINTCP
1x14W FTL
1X28W T5 LAMP
2
L1
456
TELEPHONE SOCKETTP
8
CEILING FANF
BU
LK H
EA
D3
L3
B
SL.N
o.
A C D E F G H
1
F GE H
23
45
67
89
1011
12
KIT
CO
Ltd.PU
THIY
A R
OA
D - N
H BY
PASS, K
OCH
I - 28(Estd. in 1972 by ID
BI &
Govt. of K
erala)
DR
G N
O:
REV.
SH
EET N
O:
DATE:
SC
ALE:
INITIAL
DATE
UN
IT:
APP
RO
VED
CH
ECKED
DR
AW
N
CH
ECKED
DES
IGN
ED
TITLE:
CLIEN
T:
PR
OJE
CT:
PAR
TICU
LARS
SPO
RTS & YO
UTH
AFFAIR
S DE
PARTM
ENT -
NATIO
NA
L GA
ME
S SEC
RATAR
IATE
CO
NSTR
UC
TION
OF S
TAD
IUM
& A
LLIED
FAC
ILITIESA
T CH
EN
GAN
NO
OR
-: CH
ANG
E R
OO
M AN
D LO
CK
ER R
OO
M :-
LIGH
TING
LAYO
UT
DP
645 DR
G E
L 06 0021 O
F 101.02.13
N.T.S
mm
.
boqchengannur.pdfMASTER PLAN 18.05 Model (1).pdfSLD Model (1) (1).pdfNEW CHANGE ROOMS 15.05 Model (1).pdfchange rooms Model (1).pdf