laboratory glassware washers - fisher scientific · 2011-07-17 · • minimum purified water...

FlaskScrubber® & SteamScrubber®

Laboratory Glassware Washers

NEW!FlaskS c rubbe r &

SteamScrubber racks

now interchangeable

General Features• Patent-pending design

• Lower spindle rack, of Type 304 stainless steel, with 36 detachablelarge spindles for washing narrow-neck glassware. Eighteen glass-ware holders, 36 clips and 10 additional interchangeable smallspindles are included. Rack accommodates a variety of inserts forholding beakers, culture tubes and other specialty glassware(inserts sold separately). See pages 6-7.

• Water temperature reaches 82° C (180° F) on 115 Volt models and93° C (199° F) on 230 Volt models to sanitize glassware and forenhanced washing and faster drying

• LCD information center for customizing cycles and monitoring oper-ation, including internal water temperature (° C or ° F)

• Water recirculation rates of 96 gal/min (363 liters/min) whenoperated on 115 Volt, 60 Hz and 230 Volt, 50 Hz and 112 gal/min(424 liters/min) on 230 Volt, 60 Hz for thorough cleaning

• Dual pumps, one for washing and one for draining, to reducepotential for cross contamination

• Built-in purified water pump to bring non-pressurized or pressur-ized purified water into the tank for up to six pure water rinses

• Built-in steam generator that produces hot vapor to penetrate andremove dried residue for cleaner glassware

• Manual-fill detergent dispenser for powder or liquid detergent

• Manual-fill rinse aid solution dispenser

• Built-in forced air drying through the spindles up to 99 minutesand programmable from 38-70°C (100-158° F)

• Factory-set cycle programs. All 115 volt models have sevenprograms: RINSE ONLY, PLASTIC, GLASS, GLASS PLUS, SCIENTIFIC,SCIENTIFIC PLUS, and DRY ONLY. All 208/240 Volt models havethree additional programs for a total of ten: INTENSE, INTENSEPLUS and EXTREME.

• Alarms with display for HOT GLASS, PLEASE WAIT, WATER LOW,WATER HIGH and OVERFLOW

• Two user-set cycle programs

• User-set delayed start (up to 8 hours)

• Type 304, brushed stainless steel door, tank, upper and lower washarms. Freestanding models also have stainless steel exterior sidesand top.

• One-piece, stainless steel, fine mesh particle drain filter to trapdebris in tank to protect the pumps

• No center water distribution tower allowing for greater glasswarecapacity

• Four leveling feet

• 3/8" Female NPT inlet fitting for hot tap water connection

FlaskScrubber Laboratory Glassware Washer 10-359-114

• Factory-installed drain hose and band clamp

• Two year warranty on parts and labor

• Made in the U.S.A.

• IQ/OQ available on line. Contact Labconco about on-site validationservice (sold separately).

• Accommodate optional Upper Spindle Rack with additional wash armand side release latches. See page 6.

• More versatility. Accommodate optional Upper and Lower StandardRacks. See page 6.

Requirements• Minimum inlet water temperature 49° C (120° F)

• Recommended inlet water temperature 60° C (140° F)

• Minimum purified water pressure 0 psi

• Water consumption per fill 3.4 gallons (13 liters)

• Hot tap water pressure at the washer 20-120 psi

• Hot tap water flow rate 1.25 gallons (4.7 liters) per minute

• 3/8" OD copper tubing for connection to the water inlet valve

• Purified water with supply piping minimum 3/8" ID to permit atleast 0.9 gallon (3.4 liters) per minute flow

Exclusive Labconco feature

NEW

NEW

NEW

NEW

NEW

NEW

NEW

FlaskScrubber® Laboratory Glassware Washers

Catalog # Style Electrical Maximum Internal Viewing Window Overall Dimensions ShippingRequirements Water Temperature and Light with Door Closed Weight

10-359-108 Undercounter 115 volts, 60 Hz, 16 Amps 82° C (180° F) No 24.1" w x 27.4" d x 34.1-36.1" h 182 lbs. (83 kg)

10-359-109 Undercounter 208/240 volts, 50/60 Hz, 12 Amps 93° C (199° F) No 24.1" w x 27.4" d x 34.1-36.1" h 182 lbs. (83 kg)

10-359-110 Undercounter 115 volts, 60 Hz, 16 Amps 82° C (180° F) Yes 24.1" w x 27.4" d x 34.1-36.1" h 182 lbs. (83 kg)

10-359-111 Undercounter 208/240 volts, 50/60 Hz, 12 Amps 93° C (199° F) Yes 24.1" w x 27.4" d x 34.1-36.1" h 182 lbs. (83 kg)

10-359-112 Freestanding 115 volts, 60 Hz, 16 Amps 82° C (180° F) No 24.2" w x 27.5" d x 34.2-36.2" h 229 lbs. (104 kg)

10-359-113 Freestanding 208/240 volts, 50/60 Hz, 12 Amps 93° C (199° F) No 24.2" w x 27.5" d x 34.2-36.2" h 229 lbs. (104 kg)

10-359-114 Freestanding 115 volts, 60 Hz, 16 Amps 82° C (180° F) Yes 24.2" w x 27.5" d x 34.2-36.2" h 229 lbs. (104 kg)

10-359-115 Freestanding 208/240 volts, 50/60 Hz, 12 Amps 93° C (199° F) Yes 24.2" w x 27.5" d x 34.2-36.2" h 229 lbs. (104 kg)

2

NEW

NEW

NEW


• Upper and lower racks, of Type 304 stainless steel. Upper rack hasadditional wash arm and side release latches for easy lift out.Racks accommodate a variety of inserts for holding beakers, culturetubes and other specialty glassware (inserts sold separately). Seepages 6-7.

• Water temperature reaches 82° C (180° F) on 115 Volt models and93° C (199° F) on 230 Volt models to sanitize glassware and forenhanced washing and faster drying


• Water recirculation rates of 96 gal/min (363 liters/min) when oper-ated on 115 Volt, 60 Hz and 230 Volt, 50 Hz and 112 gal/min(424 liters/min) on 230 Volt, 60 Hz for thorough cleaning





• Manual-fill rinse aid solution dispenser

• Built-in forced air drying up to 99 minutes and programmable from38-70°C (100-158° F)

• Factory-set cycle programs. All 115 volt models have sevenprograms: RINSE ONLY, PLASTIC, GLASS, GLASS PLUS, SCIENTIFIC,SCIENTIFIC PLUS, and DRY ONLY. All 230 Volt models have threeadditional programs for a total of ten: INTENSE, INTENSE PLUS andEXTREME.

• Alarms with display for HOT GLASS, PLEASE WAIT, WATER LOW,WATER HIGH and OVERFLOW







• 3/8" Female NPT inlet fitting for hot tap water connection


SteamScrubber Laboratory Glassware Washer 10-359-106 shown with 48-Pin Insert 10-359-122, Petri Dish Insert 10-359-120, Bulk Tube Insert15-352-827, Utensil Holder 15-352-826 and BOD Bottle Insert 10-359-121.




• More versatility. Accommodate optional Upper and Lower SpindleRacks (without forced air drying through the spindles). See page 6.










NEW

NEW

NEW

NEW

NEW

NEW

NEW

SteamScrubber® Laboratory Glassware Washers


10-359-100 Undercounter 115 volts, 60 Hz, 16 Amps 82° C (180° F) No 24.1" w x 27.4" d x 34.1-36.1" h 182 lbs. (83 kg)

10-359-101 Undercounter 208/240 volts, 50/60 Hz, 12 Amps 93° C (199° F) No 24.1" w x 27.4" d x 34.1-36.1" h 182 lbs. (83 kg)

10-359-102 Undercounter 115 volts, 60 Hz, 16 Amps 82° C (180° F) Yes 24.1" w x 27.4" d x 34.1-36.1" h 182 lbs. (83 kg)

10-359-103 Undercounter 208/240 volts, 50/60 Hz, 12 Amps 93° C (199° F) Yes 24.1" w x 27.4" d x 34.1-36.1" h 182 lbs. (83 kg)

10-359-104 Freestanding 115 volts, 60 Hz, 16 Amps 82° C (180° F) No 24.2" w x 27.5" d x 34.2-36.2" h 229 lbs. (104 kg)

10-359-105 Freestanding 208/240 volts, 50/60 Hz, 12 Amps 93° C (199° F) No 24.2" w x 27.5" d x 34.2-36.2" h 229 lbs. (104 kg)

10-359-106 Freestanding 115 volts, 60 Hz, 16 Amps 82° C (180° F) Yes 24.2" w x 27.5" d x 34.2-36.2" h 229 lbs. (104 kg)

10-359-107 Freestanding 208/240 volts, 50/60 Hz, 12 Amps 93° C (199° F) Yes 24.2" w x 27.5" d x 34.2-36.2" h 229 lbs. (104 kg)

3

NEW

NEW

NEW


• Lower spindle rack, of Type 304 stainless steel, with 36 detachablelarge spindles for washing narrow-neck glassware. Eighteen glass-ware holders, 36 clips and 10 additional interchangeable smallspindles are included. Rack accommodates a variety of inserts forholding beakers, culture tubes and other specialty glassware(inserts sold separately). See pages 6-7.

• Water temperature reaches 93° C (199° F) to sanitize glassware andfor enhanced washing and faster drying


• Water recirculation rates of 96 gal/min (363 liters/min) when oper-ated on 230 Volt, 50 Hz models and 112 gal/min (424 liters/min)on 230 Volt, 60 Hz for thorough cleaning




• Water conductivity monitor to confirm rinse water cleanliness andeffective detergent removal

• RS-232 port for monitoring washer operation on a user-suppliedcomputer or recorder

• Automatic liquid detergent dispenser with peristaltic pump • Automatic rinse aid dispenser


• Manual-fill rinse solution dispenser

• Built-in, HEPA-filtered forced air drying through the spindles up to99 minutes and programmable from 38-70°C (100-158° F). HEPAfilter is 99.97% efficient on particulates 0.3 micron.

• Ten factory-set cycle programs: RINSE ONLY, PLASTIC, GLASS, GLASSPLUS, SCIENTIFIC, SCIENTIFIC PLUS, INTENSE, INTENSE PLUS,EXTREME, and DRY ONLY

• Alarms with display for HOT GLASS, PLEASE WAIT, WATER LOW,WATER HIGH, OVERFLOW, LIQUID DETERGENT and RINSE AID




• Clear tempered safety glass viewing window• 25-watt interior light




FlaskScrubber Vantage Laboratory Glassware Washer 10-359-114

• 3/8" IPS inlet fitting for hot tap water connection





• Accommodate optional Upper Spindle Rack with additional wash armand side release latches. See page 6.

• More versatility. Accommodate optional SteamScrubber Upper andLower Racks. See page 6.










NEW

NEW

NEW

NEW

NEW

NEW

FlaskScrubber® Vantage® Series Laboratory

Glassware Washers


10-359-116 Freestanding* 208/240 volts, 50/60 Hz, 12 Amp 93° C (199° F) Yes 32.2" w x 27.5" d x 34.2-36.2" h 260 lbs. (118 kg)

* Convertible to undercounter4

NEW

NEW

NEW

NEW

NEW

27.4"(69.6 cm)

49.6"(126.0 cm)

24.1"(61.2 cm)

36.1" MAX(91.7 cm)

34.1" MIN(86.6 cm)

49.7"(126.2 cm)

27.5"(69.8 cm)

36.2" MAX(91.9 cm)

34.2" MIN(86.9 cm)

24.2"(61.6 cm)

36.2" MAX(91.9 cm)

34.2" MIN(86.9 cm)

49.7"(126.2 cm)

27.5"(69.8 cm)

32.2"(81.7 cm)

FRONT SIDE

FlaskScrubberVantage Series*

FreestandingFlaskScrubber &SteamScrubber

UndercounterFlaskScrubber &SteamScrubber

*Freestanding model may beconverted to undercounter

Dimensional Data

5

Utensil Basket 15-352-813For miscellaneous labware such asstoppers, spatulas and other smalllightweight items that will not passthrough No. 4 mesh sides andbottom. Retainer top is required andincluded. Type 304 stainless steel.Dimensions: 8.0" w x 8.0" d x 4.0" h(20 x 20 x 10 cm). Shipping weight2 lbs. (1 kg).

Lower Spindle Rack 10-359-202One is included with everyFlaskScrubber and FlaskScrubberVantage Series Glassware Washer. Maybe used in place of the LowerStandard Rack in any SteamScrubber.Constructed of Type 304 stainlesssteel. Includes 36 removable spindles,36 adjustable height clips, 10 small

spindles, 18 plastic glassware holders, tool to remove spindles and 36nylon plugs. Spindles may be removed and plugged to accommodateaccessory inserts (sold separately). Spindle dimensions: 7.4" high x1/4"OD. Overall dimensions: 21.1" w x 21.0" d x 8.6" high (54 x 53 x22 cm). Accommodate glassware up to 9.8" high (without upper rack inplace). Accommodate glassware up to 4.8" high (with upper rack inplace). Shipping weight 20 lbs. (9 kg).

Upper Spindle RacksConstructed of Type 304 stainlesssteel. Include side release latches, 30removable spindles, 30 adjustableheight clips, 10 small spindles, 15plastic glassware holders, tool toremove spindles, 30 nylon plugs, andwash arm. Spindles may be removedand plugged to accommodate acces-

sory inserts (sold separately). Spindle dimensions: 5.25" high x 1/4"OD.Overall dimensions: 20.0" w x 20.9" d x 7.2" high (51 x 53 x 18 cm).Accommodate glassware up to 8.5" high.

Base StandsElevate washers 17"(43.2 cm) for washerloading convenienceand storage of supplies.Type 304 stainless steelstationary stand, fullyassembled with levelingfeet and instructions.

Utensil Holder 15-352-826For spatulas, spoons, scoops andother miscellaneous utensils. Utensilsfit vertically in four compartments,2.75" w x 3.5" d x 4.9" h (7 x 9 x12 cm). Type 304 stainless steel.Dimensions: 10.8" w x 4.1" d x6.6" h (27 x 11 x 17 cm). Shippingweight 4 lbs. (2 kg).▲▼ ▼

▲▼ ▼▲

Upper Standard Racks One rack is included with everySteamScrubber. May be used in anyFlaskScrubber or FlaskScrubberVantage Series. Constructed of Type304 stainless steel. Include siderelease latches and wash arm. Addaccessory inserts below and on pages

7 and 8 to suit your glassware mix (sold separately). Dimensions:20.2" w x 20.9" d x 6.0" h (51 x 53 x 15 cm).

Guide to AccessoriesUse the icon key below to select accessories that fit your washer. Rackscan accommodate a maximum of two inserts except Utensil Holders andUtensil Baskets; racks can hold a maximum of five Utensil Holders* orfour Utensil Baskets.

For use in SteamScrubber

For use in FlaskScrubber

For use in FlaskScrubber Vantage Series

▲ Fits in Upper Standard Rack

▼ Fits in Lower Standard Rack

▼ Fits in Lower Spindle Rack with spindles removed and plugged

▲ Fits in Upper Spindle Rack with spindles removed and plugged

* Four Utensil Holders maximum in FlaskScrubber and FlaskScrubber Vantage Series Washers.

Accessories

Lower Standard Rack 10-359-118One is included with everySteamScrubber. May be used in anyFlaskScrubber or FlaskScrubberVantage Series. Constructed of Type304 stainless steel. Add accessoryinserts below and on pages 7 and 8to suit your glassware mix (sold

separately). Dimensions: 21.1" w x 21.0" d x 3.5" h (54 x 53 x 9 cm).Shipping weight 10 lbs. (5 kg).

V

V

V

V

V

V

V

6

V

V

Catalog # Description Shipping Wt.

10-359-125 Upper Spindle Rack for FlaskScrubber and 20 lbs. (9 kg)FlaskScrubber Vantage Series Glassware Washers.Includes side rails for tank side wall installation.Provides direct injection cleaning and forced air drying through the spindles.

10-359-201 Upper Spindle Rack for SteamScrubber 16 lbs. (7 kg)Glassware Washers. Provides direct injection cleaning through the spindles.


10-359-200 Upper Standard Rack for FlaskScrubber and 16 lbs. (7 kg)FlaskScrubber Vantage Series Glassware Washers.Includes side rails for tank side wall installation.

10-359-117 Upper Standard Rack for SteamScrubber 12 lbs. (5 kg)Glassware Washers


10-359-127 Stand for Freestanding FlaskScrubbers or 80 lbs. (36 kg)SteamScrubbers, 24.2" w x 27.5" d x 17.0" h(61 x 70 x 43 cm), includes one storage compartment with hinged door

10-359-126 Stand for FlaskScrubber Vantage Series, 105 lbs. (48 kg)32.2" w x 27.5" d x 17.0" h (82 x 70 x 43 cm),includes two storage compartments with hinged doors

Bulk Tube Insert 15-352-827Quick loading. For vertically-posi-tioned test tubes. Holds up to 600each 13 mm tubes or 244 each20 mm tubes. Bottom, grate size0.38" (9.5 mm), allows water to drainfrom inverted tubes. When insert isless than fully loaded, the divider may

be adjusted to keep tubes upright. Type 304 stainless steel. Smallestdivided compartment size: 1.8" w x 8.1" d x 4.2" h (4 x 21 x 11 cm).Overall interior dimensions (without divider): 18.7" w x 8.1" d x 4.2" h(48 x 21 x 11 cm). Dimensions: 21" w x 8.3" d x 4.4" h (53 x 21 x11 cm) Shipping weight 5 lbs. (2 kg).


15-352-808F Holds 8 pipets, 1 ml to 10 ml. Includes one 1.25" mounting spindle. 2 lbs. (1 kg)Includes 1.25" mounting spindle.

10-359-123 Holds 16 pipets, 1 ml to 50 ml. Includes two 1.25" mounting 3 lbs. (1 kg)spindles and PVC-coated holder.

Culture Tube InsertsChoose from three inserts designedto hold tubes from 10 to 24 mmOD. Type 304 stainless steel.

BOD Bottle Insert 10-359-121Type 304 stainless steel. Capacity:18 bottles. Grid size: 70 mm x 70mm. Dimensions: 19.5" w x 8.8" d x6.0" h (49.5 x 22.2 x 15.2 cm).Shipping weight 2.0 lbs. (0.9 kg).

Labware InsertsPins hold a variety of wider-mouthflasks, beakers and other labware ininverted position. Retainer Top isrecommended for use with plasticand lightweight glassware. Insertsand Retainer Top of Type 304 stain-less steel. Stainless steel pins haveplastic tips to protect glasswarefrom scratching.

Petri Dish Insert 10-359-120For petri dishes, watch glasses andmicrotiter plates. Capacity: 24plates. Grid size: 22 mm x 140mm. Type 304 stainless steel.Dimensions: 19.2" w x 8.6" d x5.9" h (49 x 22 x 15 cm).Shipping weight 2 lbs. (1 kg).

DNA Sequencing Plate Insert10-359-124For electrophoresis plates, 10" x16.6". Capacity: 6 plates. Type 304stainless steel with plastic glides.Dimensions: 17.1" w x 8.5" d x9.9" h (43 x 22 x 25 cm).Shipping weight 6 lbs. (3 kg).

Pipet InsertsPermit direct injection cleaning of pipets. Self-sealing silicone checkvalves allow washing of partial or full loads. Type 304 stainless steel.FlaskScrubber and FlaskScrubber Vantage Series Washers hold up to four15-352-808F or two 10-359-123 Inserts.

48-Pin Insert 10-359-122Forty-eight pins accommodate avariety of labware. Type 304 stain-less steel. Stainless steel pins haveplastic tips to protect glasswarefrom scratching. Dimensions:7.8" w x 19.3" d x 5.2" h (20 x49 x 13 cm). Shipping weight2 lbs. (1 kg).

▲▼ ▲▼

▲▼

▲▼

▼ ▼

▲▼ ▲▼

▲▼ ▼▲

▲▼ ▼▲

▼ ▼

▼

*Includes 15-352-817 Retainer Top

▼

Accessories

Tray Insert 10-359-203For pans, instrument trays, multi-purpose trays and other shallowcontainers. Capacity: 5 trays.Type 304 stainless steel.Dimensions: 18.2" w x 12.2" d x9.1" h (46 x 31 x 23 cm).Shipping weight 2 lbs. (1 kg).

▼ ▼

▲▼ ▼▲

7

Catalog # Description Dimensions Shipping Wt.

15-352-808A 10-Pin Insert 19.3" w x 8.8" d x 8.0" h 3 lbs. (1 kg)(49 x 22 x 20 cm)

16-080-33 32-Pin Insert 19.3" w x 8.8" d x 6.0" h 3 lbs. (1 kg)(49 x 22 x 20 cm)

16-080-34 Retainer Top 18.5" w x 8.0" d x 0.3" h 2 lbs. (1 kg)(47 x 20 x 1 cm)

▲▼

▲▼

▲▼ ▲▼

Catalog # Description Dimensions Grid Size Shipping Wt.

10-359-119* 242 tubes, 18.0" w x 8.6" d x 4.5" h 16.8 mm x 4 lbs.10 mm to 12 mm (46 x 22 x 11 cm) 16.8 mm (2 kg)

15-352-815 144 tubes, 18.0" w x 7.8" d x 6.4" h 23.8 mm x 3 lbs.15 mm to 18 mm (46 x 20 x 16 cm) 23.8 mm (1 kg)

15-352-816 105 tubes, 18.0" w x 8.3" d x 9.9" h 26.5 mm x 3 lbs.20 mm to 24 mm (46 x 21 x 25 cm) 26.5 mm (1 kg)

15-352-817 Retainer 18.5" w x 8.3" d x 0.3" h — 2 lbs.Top (47 x 21 x 1 cm) (1 kg)

Glassware HoldersGrip glassware over spindles.

▼▲

Accessories and Consumable Products

Freestanding-to-Mobile Conversion KitsAdd mobility to freestanding SteamScrubber and FlaskScrubber GlasswareWashers. Allow washers to be plugged into a 20 amp electrical wall out-let and connected to a standard laboratory sink faucet. Include four 2-inch diameter rubber casters, two aerator adapters for connection tostandard 55/64"-27 male and 15/16"-27 female laboratory faucets,drain hose and installation instructions. Not for use with undercounterwashers or FlaskScrubber Vantage Series Glassware Washers.


10-359-206 Mobile Conversion Kit, for 115 volt operation. 60 lbs. (27 kg)Includes 10' power cord with NEMA 5/20 plug.

10-359-207 Mobile Conversion Kit, for 230 volt operation. 60 lbs. (27 kg)Includes 8.2' power cord with NEMA 6/20 plug.

Small Spindles with Clips 10-359-204Included with every FlaskScrubber and FlaskScrubber Vantage SeriesGlassware Washer. Type 304 stainless steel. Spindles may be used inany spindle location on any Upper or Lower Spindle Rack to providedirect injection cleaning of small narrow neck glassware. Each spindleis 4.3" h x .12" OD. Package of 10 spindles with 10 height adjustmentclips. Shipping weight 3 lbs. (1 kg).

Liquid Detergent Dispenser Kit 10-359-205 Connects to any SteamScrubber or FlaskScrubber Glassware Washer duringinstallation to automate liquid detergent dispensing. Includes peristalticpump, float switch, tubing, one gallon plastic container and installationinstructions. Detergent is not included. Not for use with FlaskScrubberVantage Series Glassware Washers. Shipping weight 10 lbs. (5 kg).

Drain Water Cooling Kits Provide plumbing components, solenoid valve and electrical connectionsnecessary to mix cold tap water with hot drain water so that water<60° C (<140° F) is directed to the house drain system. When thewasher’s drainage pump is activated, the solenoid valve opens releasingthe flow of cold tap water to the drain.


10-359-208 Cold Water Drain Kit, 115 volt, 60 Hz operation 8 lbs. (4 kg)10-359-209 Cold Water Drain Kit, 230 volt, 50/60 Hz operation 8 lbs. (4 kg)

V

LabSolutions™ Non-Foaming Powder DetergentSpecially formulated for Labconco glassware washers. Removes most labcontaminants such as grease, agar, blood and protein digestates. Rinsescompletely. Non-foaming formula does not promote leaks. A 1% solutionhas a pH of approximately 12.5. Contains phosphates. Non-hazardousformula may be shipped anywhere.

LabSolutions™ Low-Foaming Liquid DetergentSpecially formulated for Labconco glassware washers. Removes a widerange of laboratory contaminants. Rinses completely. Non-corrosiveformula won’t degrade stainless steel, glass or plastic. Phosphate-freefor environmentally-safe disposal. Chlorine-free and tissue culture-safe.May be used in hot or cold water.

Catalog# Description Shipping Wt.

04-334-2 Neutralizing Acid Rinse, fills reservoir approximately 6 times 3 lbs. (1 kg)34 ounces (1 liter)

LabSolutions LiquidDetergent 04-334-1,Neutralizing Acid Rinse04-334-2, and PowderDetergent 04-335 and 04-334

LabSolutions™ Neutralizing Acid RinseSpecially formulated for rinse aid reservoir in Labconco glasswarewashers. Mild acid corrects pH reducing alkaline detergent residue.Removes hard water deposits, mineral deposits, accumulated lime scalethat can cloud glassware. Rinses completely.


04-334-1 Low-Foaming Liquid Detergent for approximately 180 loads 12 lbs. (5 kg)1 gallon (3.8 liters)


15-352-808D 4.0" h (10 cm) vinyl-coated 0.4 lb. (0.2 kg)Type 304 stainless steel wirewith height adjustment screw

15-352-808E 6.0" h (15 cm) vinyl-coated 0.4 lb. (0.2 kg)Type 304 stainless steel wirewith height adjustment screw


04-334 Powder Detergent, small pail for approximately 140 loads 10 lbs. (5 kg)04-335 Powder Detergent, large pail for approximately 400 loads 28 lbs. (13 kg)

4-10-9/07-__-5M-R3Fisher Bulletin #____

For customer service, call 1-800-766-7000To fax an order, use 1-800-926-1166To order online: www.fishersci.com

Made in the UnitedStates of America

Fisher Scientific Canada:For customer service, call 1-800-234-7437To fax an order, use 1-800-463-2996To order online: www.fishersci.ca

©2007 by Labconco Corporation. Printed in the U.S.A. Product design subject to change without notice.

Fisher HealthCare:For customer service, call 1-800-640-0460To fax an order, use 1-800-290-0290To order online: www.fisherhealthcare.com

laboratory glassware washers - fisher scientific · 2011-07-17 · • minimum purified water...

Documents