lancaster b mk.iii dambuster interior s.a. 73 484 - eduardfor further detail sets look for eduard72...
TRANSCRIPT
-
1/4 73 484
Lancaster B Mk.III Dambuster interior S.A.73 4841/72 scale detail set for Airfix kit • sada detailů pro model 1/72 Airfix
ORIGINAL KIT PARTSPŮVODNÍ DÍLY STAVEBNICE
PHOTO-ETCHED PARTSLEPTANÉ DÍLY
PARTS TO BE REMOVEDDÍLY K ODSTRANĚNÍ
FILLTMELIT
eduard
REMOVEODSTRANIT
OPTIONVOLBA?REPLACENAHRADIT
BENDOHNOUT
GRINDOBROUSIT
SYMETRICAL ASSEMBLYSYMETRICKÁ MONTÁŽ
DRILL HOLEVRTAT OTVOR
APPLY EXPRESS MASK AND PAINT BEFORE GLUINGPOUŽÍT EXPRESS MASK NABARVIT PRED SLEPENÍM
1 COLORED ETCHED PARTSLEPTANÉ BAREVNÉ DÍLY
44
85
62
74
58
75
44 43
42
79
79
74
55
46
38
83
78
72
C20, D28
37
A5
77
76
39
73
60
63
61
D26
-
57
D30
4,2mm
2/4 73 484
29
2931
27
2 pcs.
=
57
2 pcs.
88
1
2
12
32
9
20
20
28
28
21
D30
19
=
3
18
70
30
6
4
1623
22
A3
50
A3=
41
40
86
C22
fill
82
48
A3
C32
51
47
56
A3
A4
A5
7
-
© EDUARD M.A. 2013 www.eduard.com Made in Czech Republic
eduardFor further detail sets look for 72 564 Lancaster B Mk.III Dambuster exterior(not included in this set)
eduardFor further detail sets look for 72 565 Lancaster B Mk.I/Mk.III landing flaps(not included in this set)
3/4 73 484
71
D3, D4
59
66
H5H23
59
66
H5H21
x
=
8433
34
13
81D27
D14
C32
35
3611
10
D14
D27D22
47
D22
=
8
45
49
5
26
25
17
24
14
87 15
B11
C21
64
65
53 52
54
D15
D8
D32
6968
67
67
80
D31
D23
-
2. Do not inadvertently place etched componets on an unwanted surface. Attempts to remove will result in damage to your part.
2. Nepokládejte samolepící díly na volné plochy. Pokud je omylem přilepíte, při pokusu o odlepení dojde k poškození dílu.
3. Do not touch the adhesive areas of the etched components.
3. Nesahejte na části dílů, na kterých je naneseno lepidlo.1. Separate the etched components from their frames on the protective paper. Removal from the paper is done only after separation of the parts from the frames.
1.Samolepící díly oddělujte od rámečku na podkladovém papíře. Po oddělení je sejměte z krycího papíru.
4. Hold the parts by the edges, or at areas free of adhesive.
4. Samolepící díly berte za hrany nebo za části, na kterých není nanesené lepidlo.
5. Lightly place the component in the desired location and position. Adjust as required. The component will be permanently affixed when pressed onto its intended location, its location can be adjusted.
5. Díl lehce položte do pozice, ve které má být nalepen. Upravte přesnou pozici a přimáčkněte. Díl dokonale přilne až po přimáčknutí, před přimáčknutím lze dílem opatrně manipulovat.
PARTS WITH GLUE DÍLY OPATŘENÉ LEPIDLEM
4/4 73 484