LAVATORY DESIGN WORK SHEET

Double Bowl Lavatory

LEFT SIDE: RIGHT SIDE:

Answers to common questions:

- The dimensions of your vanity cabinet will tell you the correct dimensions and bowl layout of your Lavatory. Always give a good description of your cabinet.- The center of each bowl should line up with the center between the cabinet doors.- The Lavatory should overhang the cabinet in the front. The correct Lavatory

1 depth should be 1" greater than the cabinet depth (1 2 / " for full-overlay doors).- The Lavatory should overhang the cabinet on any ends that are not against walls. The correct Lavatory width should be greater than the cabinet width

1 by /2" for each open end.- A raised edge can be put on the front and both ends of a standard size, or on the front and only one end of a custom size.- If a wall-side of the Lavatory is actually against a linen cabinet that is not as deep as the Lavatory, the corner that will stick out past the cabinet will also need to be finished. Always specify the depths of side cabinets.

Measure cabinet depth from wallto front of face frame.

FINISHED EDGES: Raised Flat Ogee

Dimension should include 1/2" overhang for each finished end

FILL IN THE DIMENSIONS AND FAX THIS TO US WITH YOUR ORDER FORM001LavatoryDesignTools-06-0309

FinishWallSidesplashShort Linen

FinishWallSidesplashShort Linen

CABINET DOORS: Standard Faceframe Full-Overlay

Depth of Linen orother Side Cabinet

Depth of Linen orother Side Cabinet

LAVATORY DESIGN WORK SHEET

Single Bowl Centered Lavatory

LEFT SIDE: RIGHT SIDE:

Measure cabinet depth from wallto front of face frame.

FINISHED EDGES: Raised Flat Ogee

Dimension should include 1/2" overhang for each finished end

FILL IN THE DIMENSIONS AND FAX THIS TO US WITH YOUR ORDER FORM002

FinishWallSidesplashShort Linen

FinishWallSidesplashShort Linen

Answers to common questions:

- The dimensions of your vanity cabinet will tell you the correct dimensions and bowl layout of your Lavatory. Always give a good description of your cabinet.- The center of each bowl should line up with the center between the cabinet doors.- The Lavatory should overhang the cabinet in the front. The correct Lavatory

1 depth should be 1" greater than the cabinet depth (1 2 / " for full-overlay doors).- The Lavatory should overhang the cabinet on any ends that are not against walls. The correct Lavatory width should be greater than the cabinet width

1 by /2" for each open end.- A raised edge can be put on the front and both ends of a standard size, or on the front and only one end of a custom size.- If a wall-side of the Lavatory is actually against a linen cabinet that is not as deep as the Lavatory, the corner that will stick out past the cabinet will also need to be finished. Always specify the depths of side cabinets.

CABINET DOORS: Standard Faceframe Full-Overlay

Depth of Linen orother Side Cabinet

Depth of Linen orother Side Cabinet

LavatoryDesignTools-06-0309

LAVATORY DESIGN WORK SHEET

Measure cabinet depth from wallto front of face frame.

Include 1/2" overhang for each finished end

FINISHED EDGES: Raised Flat Ogee

Single Bowl Offset Lavatory

Include 1/2" overhang for each finished end

LEFT SIDE: RIGHT SIDE:

LEFT offset RIGHT offset

FILL IN THE DIMENSIONS AND FAX THIS TO US WITH YOUR ORDER FORM003

FinishWallSidesplashShort Linen

FinishWallSidesplashShort Linen

Answers to common questions:

- The dimensions of your vanity cabinet will tell you the correct dimensions and bowl layout of your Lavatory. Always give a good description of your cabinet.- The center of each bowl should line up with the center between the cabinet doors.- The Lavatory should overhang the cabinet in the front. The correct Lavatory

1 depth should be 1" greater than the cabinet depth (1 2 / " for full-overlay doors).- The Lavatory should overhang the cabinet on any ends that are not against walls. The correct Lavatory width should be greater than the cabinet width

1 by /2" for each open end.- A raised edge can be put on the front and both ends of a standard size, or on the front and only one end of a custom size.- If a wall-side of the Lavatory is actually against a linen cabinet that is not as deep as the Lavatory, the corner that will stick out past the cabinet will also need to be finished. Always specify the depths of side cabinets.

CABINET DOORS: Standard Faceframe Full-Overlay

Depth of Linen orother Side Cabinet

Depth of Linen orother Side Cabinet

LavatoryDesignTools-06-0309

Copy this page, write your dimensions on the copy, and fax to us for a quote.Always give stud-to-stud measurements, and distance to top of wall panels from the floor.

We will figure clearances etc. Circled numbers indicate assembly order.

Rectangular Shower- Right Side Offset Curb -

001

Rectangular Shower- Left Side Offset Curb -

SHOWER DESIGN WORK SHEET

ShowerDesignTools-03-1111

Rectangular Showerwith Bench Seat on Right Side

Using STANDARD Shower Base

Rectangular Showerwith Bench Seat on Left Side

Using STANDARD Shower Base

002

SHOWER DESIGN WORK SHEET

Copy this page, write your dimensions on the copy, and fax to us for a quote.Always give stud-to-stud measurements for base, framing height of bench seat support structure, and distance to top of wall panels from the floor. We will figure clearances etc.

Circled numbers indicate assembly order. ShowerDesignTools-03-1111

Rectangular Shower- Far End Offset Curb -

with Bench Seat on Right Side

Rectangular Shower- Far End Offset Curb -

with Bench Seat on Left Side

003

SHOWER DESIGN WORK SHEET

Copy this page, write your dimensions on the copy, and fax to us for a quote.Always give stud-to-stud measurements for base, framing height of bench seat support structure, and distance to top of wall panels from the floor. We will figure clearances etc.

Circled numbers indicate assembly order. ShowerDesignTools-03-1111

Rectangular Shower- Near End Offset Curb -

with Bench Seat on Right Side

Rectangular Shower- Near End Offset Curb -

with Bench Seat on Left Side

004

SHOWER DESIGN WORK SHEET

Copy this page, write your dimensions on the copy, and fax to us for a quote.Always give stud-to-stud measurements for base, framing height of bench seat support structure, and distance to top of wall panels from the floor. We will figure clearances etc.

Circled numbers indicate assembly order. ShowerDesignTools-03-1111

Rectangular Shower- Recessed Curb -

with Bench Seat on Right Side

Rectangular Shower- Recessed Curb -

with Bench Seat on Left Side

005

SHOWER DESIGN WORK SHEET

Copy this page, write your dimensions on the copy, and fax to us for a quote.Always give stud-to-stud measurements for base, framing height of bench seat support structure, and distance to top of wall panels from the floor. We will figure clearances etc.

Circled numbers indicate assembly order. ShowerDesignTools-03-1111

Rectangular Showerwith Bench Seat on Back Wall

(view from left side)

006

Rectangular Showerwith Bench Seat on Back Wall

(view from right side)

SHOWER DESIGN WORK SHEET

Copy this page, write your dimensions on the copy, and fax to us for a quote.Always give stud-to-stud measurements for base, framing height of bench seat support structure, and distance to top of wall panels from the floor. We will figure clearances etc.

Circled numbers indicate assembly order. ShowerDesignTools-03-1111

Rectangular Attic Shower- Angled Ceiling Panels -

with Bench Seat on Back Wall(view from left side)

007

Rectangular Attic Shower- Angled Ceiling Panels -

with Bench Seat on Back Wall(view from right side)

SHOWER DESIGN WORK SHEET

Copy this page, write your dimensions on the copy, and fax to us for a quote.Always give stud-to-stud measurements for base, framing height of bench seat support structure, and distance to top of wall panels from the floor. We will figure clearances etc.

Circled numbers indicate assembly order. ShowerDesignTools-03-1111

Neo-Angle Basewith Bench Seat on Right Side

008

Neo-Angle Basewith Bench Seat on Left Side

SHOWER DESIGN WORK SHEET

Copy this page, write your dimensions on the copy, and fax to us for a quote.Always give stud-to-stud measurements for base, framing height of bench seat support structure, and distance to top of wall panels from the floor. We will figure clearances etc.

Circled numbers indicate assembly order. ShowerDesignTools-03-1111

Neo-Angle Base- Recessed Curb on Diagonal -

with Bench Seat on Right Side

009

Neo-Angle Base- Recessed Curb on Diagonal -

with Bench Seat on Left Side

SHOWER DESIGN WORK SHEET

Copy this page, write your dimensions on the copy, and fax to us for a quote.Always give stud-to-stud measurements for base, framing height of bench seat support structure, and distance to top of wall panels from the floor. We will figure clearances etc.

Circled numbers indicate assembly order. ShowerDesignTools-03-1111

010

SHOWER DESIGN WORK SHEET

Neo-Angle Base- Recessed Curb on Diagonal -with Bench Seat on Back Wall Left

Neo-Angle Base- Recessed Curb on Diagonal -with Bench Seat on Back Wall Right

Copy this page, write your dimensions on the copy, and fax to us for a quote.Always give stud-to-stud measurements for base, framing height of bench seat support structure, and distance to top of wall panels from the floor. We will figure clearances etc.

Circled numbers indicate assembly order. ShowerDesignTools-03-1111

011

SHOWER DESIGN WORK SHEET

Neo-Angle Base- Curb on Diagonal -

with Bench Seatson Back and Right Side

Neo-Angle Base- Curb on Diagonal -

with Bench Seatson Back and Left Side

Copy this page, write your dimensions on the copy, and fax to us for a quote.Always give stud-to-stud measurements for base, framing height of bench seat support structure, and distance to top of wall panels from the floor. We will figure clearances etc.

Circled numbers indicate assembly order. ShowerDesignTools-03-1111

012

SHOWER DESIGN WORK SHEET

Rectangular Shower- with ALL GLASS FRONT -and Bench Seat on Right Side

Using STANDARD Shower Base

Rectangular Showerwith ALL GLASS FRONT

and Bench Seat on Left SideUsing STANDARD Shower Base

Copy this page, write your dimensions on the copy, and fax to us for a quote.Always give stud-to-stud measurements for base, framing height of bench seat support structure, and distance to top of wall panels from the floor. We will figure clearances etc.

Circled numbers indicate assembly order. ShowerDesignTools-03-1111

013

SHOWER DESIGN WORK SHEET

JACK & JILL Shower Designwith Bench Seat on Right Side

JACK & JILL Shower Designwith Bench Seat on Left Side

Copy this page, write your dimensions on the copy, and fax to us for a quote.Always give stud-to-stud measurements for base, framing height of bench seat support structure, and distance to top of wall panels from the floor. We will figure clearances etc.

Circled numbers indicate assembly order. ShowerDesignTools-03-1111

014

SHOWER DESIGN WORK SHEET

STEAM SHOWER- with Sloped Ceiling -

and Bench Seat on Right SideUsing STANDARD Shower Base

STEAM SHOWER- with Sloped Ceiling -

and Bench Seat on Left SideUsing STANDARD Shower Base

Copy this page, write your dimensions on the copy, and fax to us for a quote.Always give stud-to-stud measurements for base, framing height of bench seat support structure, and distance to top of wall panels from the floor. We will figure clearances etc.

Circled numbers indicate assembly order. ShowerDesignTools-03-1111

Copy this page, write your dimensions on the copy, and fax to us for a quote.Always give stud-to-stud measurements for base, framing height of bench seat support structure, and distance to top of wall panels from the floor. We will figure clearances etc.

Circled numbers indicate assembly order. 015ShowerDesignTools-03-1111

SHOWER DESIGN WORK SHEET

Neo-Angle Base- STANDARD SIZE -

with Bench Seaton Back Wall Right

Neo-Angle Base- STANDARD SIZE -

with Bench Seaton Back Wall Left

Copy this page, write your dimensions on the copy, and fax to us for a quote.Always give stud-to-stud measurements for base, framing height of bench seat support structure, and distance to top of wall panels from the floor. We will figure clearances etc.

Circled numbers indicate assembly order. 016ShowerDesignTools-03-1111

SHOWER DESIGN WORK SHEET

Rectangular Base- STANDARD SIZE -

with Pony Wallson Left and Right

Copy this page, write your dimensions on the copy, and fax to us for a quote.Always give stud-to-stud measurements for base, framing height of bench seat support structure, and distance to top of wall panels from the floor. We will figure clearances etc.

Circled numbers indicate assembly order. 017ShowerDesignTools-03-1111

SHOWER DESIGN WORK SHEET

Rectangular Base- STANDARD or CUSTOM SIZE -

with Pony Wallon Right Side

Rectangular Base- STANDARD or CUSTOM SIZE -

with Pony Wallon Left Side