lee bench plate instructions bench plate instructions 3 fq1828 short bench plate bolt 4...

LEE BENCH PLATE INSTRUCTIONS 3 FQ1828 Short Bench Plate Bolt 4 FQ1869 ¼-20 x 5/16 Philips pan head 3 FQ1871 ¼” SAE Flat Washer 3 FT1994 ¼ –20 Nut 1 LS1898 Bench Plate Instructions Catalog # 90251 US Patent #7,578,489 Exp. 2028 The Lee Bench Plate allows sturdy mounting and quick changing of your reloading press or mounted accessories. The heavy steel mounting plate distributes the loading pressure over a large area, making installation a success on any bench. Dimensioned full size drawings of all Lee press mountings are available on line at www.leeprecision.com. Click on the INSTRUCTIONS button. LEE PRECISION, INC. 4275 Hwy. U · Hartford WI 53027 www.leeprecision.com Slide your press into the Bench Plate. Insert a 1/4” bolt, screwdriver shank into the lock/alignment hole. This ensures the wood block is properly aligned and will not slide out during your reloading session. Tighten the four Z-bracket screws. To remove press, loosen Z-bracket screws a turn, remove lock/alignment pin and slide from the base plate. Make sure the wood block is right side up, so that the alignment holes in the wood block and the steel plate line up. Select the appropriate length elevator bolts and secure press to base block. Tighten nut until the flat head of the bolt is flush with wood base. MOUNTING PRESS TO STEEL BASE BLOCK Hold press up to steel base block, bolt up using holes in steel base block that line up with the mounting lugs of your Lee press (see template below). Use short elevator bolts to mount your Lee press. Tighten using 7/16” wrench. 2 Drill four 1/4” holes using the bench plate as a template. If tabletop is 3/4” or thinner, use at least 1/4” through bolts with nuts and washers. If table top is 3/4” or thicker, 5/16” lag bolts work nicely. (There are six mounting holes; select four holes that don’t interfere with brackets or braces on your bench) If you are mounting a press or accessory on a wood block, drill 5/16” holes through the hexagonal and circular hole. These two holes allow the user to drop a 1/4” bolt or screwdriver shank to lock the wood block to the steel plate. 1 Mount base plate flush with front edge of your bench or sturdy table. Orientate the bench base plate with the hexagonal hole to the left. On workbenches where front edge is flush with cabinet or drawar below, use the 2nd set of holes, and mount the base plate 1/2” minimum over the front edge of the bench. Install the Z-brackets with the provided 1/4”–20 pan head screws. Start the screws in a few threads, but do not fully tighten at this point. ©2016 LEE PRECISION, INC. PRINTED IN USA LS1898 LOCK PIN & BLOCK ORIENTATION SCALE 1 : 1 MOUNTING PRESS OR ACCESSORY ON WOOD Using 3/4” (.690” to .750”) plywood and the provided drill template below, drill holes in wood block. Make sure to drill alignment lock holes as well. It is important to use the alignment/lockpin hole when using wood block. Lock pin Lock Pin Hole Lock Pin Hole Have other Lee Presses to mount? Purchase part #90267 for quick and easy press mounting. No drilling required. Pro 1000 CC TP LM BLCC Pro 1000 CC TP LM BLCC 18-PRO 18-VTP CC TP LM Pro 1000 BLCC Alignment / Lock Hole Alignment/ Lock Hole CTP CTP CTP RP RP RP BLC BLC BLC 18-PRO 18-VTP CTP Classic Turret Press LM Load-Master RP Breech Lock Reloader Press BLC Breech Lock Challenger BLCC Breech Lock Classic Cast CC Classic Cast Pro 1000 Pro 1000 TP 4 Hole ValueTurret Press 18-PRO Year 2018+ Pro 1000 Press 18-VTP Year 2018+ 4 holeValue Turret Press 18-PRO 18-VTP

Upload: duongkhanh

Post on 22-May-2018

217 views

Category:

Documents

2 download

Report

Download

Embed Size (px):

TRANSCRIPT

LEE BENCH PLATE INSTRUCTIONS

3 FQ1828 Short Bench Plate Bolt4 FQ1869 ¼-20 x 5/16 Philips pan head3 FQ1871 ¼” SAE Flat Washer3 FT1994 ¼ –20 Nut1 LS1898 Bench Plate Instructions

Catalog # 90251 US Patent #7,578,489 Exp. 2028

The Lee Bench Plate allows sturdy mounting and quick changing of your reloading press or mounted accessories. The heavy steel mounting plate distributes the loading pressure over a large area, making installation a success on any bench. Dimensioned full size drawings of all Lee press mountings are available on line at www.leeprecision.com.Click on the instructions button.

LEE PRECISION, INC.4275 Hwy. U · Hartford WI 53027www.leeprecision.com

Slide your press into the Bench Plate. Insert a 1/4” bolt, screwdriver shank into the lock/alignment hole. This ensures the wood block is properly aligned and will not slide out during your reloading session. Tighten the four Z-bracket screws. To remove press, loosen Z-bracket screws a turn, remove lock/alignment pin and slide from the base plate.

Make sure the wood block is right side up, so that the alignment holes in the wood block and the steel plate line up. Select the appropriate length elevator bolts and secure press to base block. Tighten nut until the flat head of the bolt is flush with wood base.

MOUNTING PRESS TO STEEL BASE BLOCKHold press up to steel base block, bolt up using holes in steel base block that line up with the mounting lugs of your Lee press (see template below). Use short elevator bolts to mount your Lee press. Tighten using 7/16” wrench.

2 Drill four 1/4” holes using the bench plate as a template. If tabletop is 3/4” or thinner, use at least 1/4” through bolts with nuts and washers. If table top is 3/4” or thicker, 5/16” lag bolts work nicely.

(There are six mounting holes; select four holes that don’t interfere with brackets or braces on your bench)

If you are mounting a press or accessory on a wood block, drill 5/16” holes through the hexagonal and circular hole. These two holes allow the user to drop a 1/4” bolt or screwdriver shank to lock the wood block to the steel plate.

1 Mount base plate flush with front edge of your bench or sturdy table. Orientate the bench base plate with the hexagonal hole to the left. On workbenches where front edge is flush with cabinet or drawar below, use the 2nd set of holes, and mount the base plate 1/2” minimum over the front edge of the bench.

Install the Z-brackets with the provided 1/4”–20 pan head screws. Start the screws in a few threads, but do not fully tighten at this point.

LOCK PIN & BLOCK ORIENTATION

SCALE 1 : 1

MOUNTING PRESS OR ACCESSORY ON WOOD

Using 3/4” (.690” to .750”) plywood and the provided drill template below, drill holes in wood block. Make sure to drill alignment lock holes as well. It is important to use the alignment/lockpin hole when using wood block.

Lock pinLock Pin Hole

Lock Pin Hole

Have other Lee Presses to mount? Purchase part #90267 for quick and easy press mounting. No drilling required.

Pro 1000CCTPLM

BLCC

Pro 1000CCTPLM

BLCC18-PRO18-VTP

CCTPLM

Pro 1000

BLCC

Alignment/Lock Hole

CTP

RPRP

BLC

BLC18-PRO18-VTP

CTP Classic Turret PressLM Load-MasterRP Breech Lock Reloader PressBLC Breech Lock ChallengerBLCC Breech Lock Classic CastCC Classic CastPro 1000 Pro 1000TP 4 Hole ValueTurret Press18-PRO Year 2018+ Pro 1000 Press18-VTP Year 2018+ 4 holeValue Turret Press18-PRO

18-VTP

AUTOMOTIVE LABORATORY - upnm.edu.my · Lagging Experiment Bench 5. Ejector Bench 6. Condenser Bench 7. Process Plant Bench 8. Thermal Conductivity 9. Marcet Boiler 10. Bomb Calorimeter

Bench Saw Manual - VintageMachinery.org | Welcome OPERATING INSTRUCTIONS AND PARTS LIST FOR CRAFTSMAN BENCH SAW TO-INCH TILTING ARBOR MODEL NUMBER 113.29901 The will be on o plate

· PDF filePre -Charged Pneumatic –Air Rifles ... UIT Accessory rail for hamster, bench rest plate, bi-pod studs etc Ultimate -Adjustable Tilt / Length Front rest/grip

Swing Bench

GFX 3 - Rapid Welding 3.0 Operating Manual.pdf · of a mounting plate (Accessories, see chap. 3.2, p. 12). The mounting plate is also screwed to the work bench. • The machines must

Bench Drill

MTFB12 | MTR60B | METB | MTO60B | MCTB12€¦ · Elliptical Bench Table METB Round Bench Table MTR60B Octagon Bench Table MTO60B Rectangular Bench Table MTFB12 Curve Bench Table MCTB12

PP 164 plate 17 - USGSGILBERT BENCH Jsr PLATE 17 Jsr 10,000' 9,000' 8,000' 7,000' 6,000' 5,000' - 4,000' 3,000' 2,000' 1 ,000' Paunsaugunt platform Kws HOWELL SLOPE Jsr Jgc Jsr K Kws

Bench Allocation

BENCH-ON-BENCH - Tools for Working Wood

TradeIndia · Digital Micrometer Micro Height Micrometer Head Gauge Block Set ... Bench Centre Multimeter Granite Surface Plate Thickness Gauge Measuring Instrument ... Shear Wrench