limits and fits. introduction in engineering you are usually concerned with a number of parts or...
TRANSCRIPT
Limits and FitsLimits and FitsLimits and FitsLimits and Fits
Introduction• In engineering you are usually
concerned with a number of parts or components fitting together to make an:
assembly
• To assemble components together engineers must control the sizes of the components to make sure that they fit together correctly.
• If they don’t fit together correctly then the components will not function properly.
What is a FIT in engineering terms?
• There are three types of fit used in engineering:
1. Clearance Fit2. Transition Fit3. Interference Fit
1. The Clearance Fit.This is where the shaft slides through the hole
Called the Clearance
GAP
2. The Transition Fit.This is where the shaft slides through the hole very tightly.
NO GAP
Called the Transition
3. The Interference Fit.This is where the shaft slides through the hole and shears the metal has it goes in.
SHEARING
Called the Interference
Other Names Used for the Fits
• Sliding Fit allows one part to slide in another whilst there is no force being applied to the shaft
The Clearance Fit
• A Force Fit which needs a “big Hammer” or preferable a power press to assemble the shaft and hole.
The Interference Fit• A Push Fit which means the hole
and the shaft can be push together or perhaps tapped gentle with a soft hammer.
The Transition Fit
How do we decide which fit to use?
• First consider what is required of the fit. • Then decide how much clearance or
interference you are going to give your fit.
• Then determine what nominal size you are going to fit together.
What are Nominal sizes?
• They are basically any size, it maybe any whole number you like: -
•16 12 40 60 1200 230,000
• Now you have the size, how much interference or clearance do we use?
We need a system to help!
Advantages of having a system:Interchangeable - parts made at different times or
places fit together.
Time saving - reference to a standard system speeds up decisions on sizes to give particular fits.
Assurance of correct fit - actual fit will be as required even if design size changes.
Spare Parts – manufacture of these is made easier as they can be made to the same standard.
British Standards 4500
• Uses the nominal size for both holes and shafts.
• This size is determined by strength considerations.
• Calculations of material properties and strengths are used to obtain the nominal size.
• Remember: The nominal size is the same for both hole and shaft.
BS4500• The British Standard System uses the letters
of the alphabet to describe how much bigger or smaller a hole or a shaft will deviate from the nominal size.
• This deviation is called the:-
Fundamental deviation.
• Holes are described by capital letters H, G etc.• Shafts are described by lower case letters h, g
etc.
Zero lineA B
The Fundamental Deviation
HK
M
The Fundamental Deviation
The Fundamental Deviation
Nominal Size
The Holes
The Shafts
Nominal Size
Zero Line
Fundamental Deviation
Fundamental Deviation
Nominal Size
a
b g m e
M
A
Any combination of hole and shaft can be use
e
A/e fit
aSo be careful when choosing your fits they don’t all work
M/a fit
British Standards Tolerance zones
Tolerance Zone
BS4500 use numbered tolerance zones (01 to 16)
• The most accurate tolerance zones are numbered 01 02 and 03.
• Whereas for more general engineering work we use 06, 07 and 08.
• Finally, rough work is done at 14,15 and 16.
British Standards Tolerance zones
In engineering we don’t use the zeros
Round up• You now have a letter and a
number.
• Put them together and you have the type of fit and the tolerance that will achieve it. Examples are:
»H7, K8 and M9.» For holes.
• For shafts we use:• g6, h7 and f7.
• Here then is the complete fit:
• The Hole The shaft
H9 f7
BS 4500
Limits of size• Look on the chart
• Maximum and minimum allowances are shown in thousandths of a millimetre • Minimum clearance and minimum
interference is minimum hole size minus maximum shaft size
• Tolerance is max deviation minus min deviation
Bush
Shaft
PulleySpacerHousing
Standard washer
Today's task
Decide what fits are required between the shaft and bush and the bush and pulley. Give reason for your choices in not less than 600 words.
Bush pressed in using force. Fit is Interference
Shaft must be allowed to slide so pulley and bush can rotate
Pulley
Spacer creates another type of fit
H7 Hole
P6 Shaft
Fit should be Clearance Fit
Choice is: -H7 Hole in both cases and for the shaft either g6 or h6
Clearance fit: -
H7 hole (width of bush) and g6 for the shaft (length to first shoulder)
When does Tolerances become important
• Assemblies: Parts will often not fit together if their
• dimensions do not fall with in a certain range of values
When do Tolerances become important
• Interchangeability• If a replacement part is used it
must be• a duplicate of the original part
within certain limits of deviation.
When do Tolerances become important
• Tolerances do not affect the function here
When do Tolerances become important
• Tolerances are important here !
When do Tolerances become important
• What about the tolerance levels in this mechanism?
Straightness
Geometric tolerance
Measuring and gauging• Measuring is a direct reading
process in which the inspection instrument consists of (or incorporates ) a continuous series of linear measurement units, commonly known as a scale.
Measuring and gauging• Gauging is checking that a
component fits within tolerance limits
• Tolerances for Go gauges are placed within working limits
• Tolerances for No Go gauges are outside working limits
Plug gauge
Snap go/no go gauge for the OD of a
cylindrical workpie
Replaceable thread and plug gauges
Plug Gauge operation
Hole Diameter (mm)
Dia of Go End Dia of No Go end
a, 40 ± 0.02 39.98 40.02
b, 46 + 0.03 46.00 45.03
C, 30 - 0.2 29.80 30.00
Other gauges