Installation Manual &Operation Instructions

www.iaexim.com

TMIowa Export-Import LIMITED WARRANTY STATEMENT

Iowa Export-Import warrants this product to be free from defects in material and workmanship for a period of eighteen (18) months from the date of sale to theoriginal purchaser. Iowa Export-Import will repair this product free of charge if, inthe judgment of Iowa Export-Import, it has been proven defective within the war-ranty period. The product should be returned, at the customer expense, to thelocation of original purchase. This warranty does not cover any expensesincurred in the removal and/or reinstallation of the product.

This warranty does not apply to any product damaged by improper installation,accidental misuse, abuse, improper line voltage, fire, flood, lightning, or otheracts of God, or a product altered or repaired by anyone other than Iowa Export-Import. This warranty is in lieu of other warranties, expressed or implied, includ-ing any implied warranty of merchantability. No person is authorized to assumefor Iowa Export-Import any other liability concerning the sale of this product.

IMPORTANT-KEEP YOUR INVOICE WITH THIS WARRANTY STATEMENT!

LinearActuatorControllerLA-Controller

www.iaexim.com

TM

05/07 Technical Support: (800) 831-4145

FUSE

7.5

11 3322

Features:This unit features 3 user programmable presets that are easily accessed via the pushbutton display to precisely control one linear actuator. Linear actuators can be used to open trunks, hoods, etc.Once the linear actuator has reached a point that you would like to make a preset, simply press and hold the corresponding button for 5 seconds. The position will have been learned by the main control unit and visually indicated by a led flashing above the programmed preset.

**Proper wiring is critical to the correct operation of this unit. Inspect all wiring to be certain of proper connections, a good quality ground, and proper fusing. Also check wire routing, keeping wires away from potential damage, such as moving parts.**

2 7

11 3322

Features:This unit features 3 user programmable presets that are easily accessed via the pushbutton display to precisely control one linear actuator. Linear actuators can be used to open trunks, hoods, etc.Once the linear actuator has reached a point that you would like to make a preset, simply press and hold the corresponding button for 5 seconds. The position will have been learned by the main control unit and visually indicated by a led flashing above the programmed preset.

**Proper wiring is critical to the correct operation of this unit. Inspect all wiring to be certain of proper connections, a good quality ground, and proper fusing. Also check wire routing, keeping wires away from potential damage, such as moving parts.**

2 7

11 3322

Features:This unit features 3 user programmable presets that are easily accessed via the pushbutton display to precisely control one linear actuator. Linear actuators can be used to open trunks, hoods, etc.Once the linear actuator has reached a point that you would like to make a preset, simply press and hold the corresponding button for 5 seconds. The position will have been learned by the main control unit and visually indicated by a led flashing above the programmed preset.

**Proper wiring is critical to the correct operation of this unit. Inspect all wiring to be certain of proper connections, a good quality ground, and proper fusing. Also check wire routing, keeping wires away from potential damage, such as moving parts.**

2 7

11 3322

Features:This unit features 3 user programmable presets that are easily accessed via the pushbutton display to precisely control one linear actuator. Linear actuators can be used to open trunks, hoods, etc.Once the linear actuator has reached a point that you would like to make a preset, simply press and hold the corresponding button for 5 seconds. The position will have been learned by the main control unit and visually indicated by a led flashing above the programmed preset.

**Proper wiring is critical to the correct operation of this unit. Inspect all wiring to be certain of proper connections, a good quality ground, and proper fusing. Also check wire routing, keeping wires away from potential damage, such as moving parts.**

2 7

www.iaexim.com www.iaexim.com

Explanation:This unit features 3 user programmable presets that are easily accessed via the push-button display to precisely control one linear actuator. Linear actuators can beused to open trunks, hoods, etc.

Once the linear actuator has reached a point that you would like to make a preset,simply press and hold the corresponding button for 5 seconds. The position will havebeen learned by the main control unit and visually indicated by a led flashing above the programmed preset.

**Proper wiring is critical to the correct operation of this unit. Inspect all wiring to becertain of proper connections, a good quality ground, and proper fusing. Also check wire routing, keeping wires away from potential damage, such as moving parts.**

Each Kit Contains the Following Components: Optional Wiring(1) Display (1) Double-Sided Tape

(1) Central Control Unit (1) Mounting Hardware

(1) Wire Harness (1) Display Harness

2 7

Green: Preset #3

Black

Red

White: Preset#1

Yellow

Blue: Preset #2

RETAB TY

Ignition

BlackRed

PurpleWhiteYellow

11 3322

BlackRed

Yellow

FUSE5

FUSE

7.5

Brown: Channel 4Orange: Channel 3

Blue: Channel 5

SPAL Shaved Dooor Kit

Shaved Door Kit & LA Controller

Custom Buttons

Green

BlackRed

WhiteYellow

Blue

RETAB TYIgnition

Preset #1 Input Switch

Preset #2 Input Switch

Preset #3 Input Switch

BlackRed

PurpleWhiteYellow

Ground

Optional Accessories- 10' Linear Actuator Extension Harness - Linear Actuators 2, 4, 6, 8-Inch

www.iaexim.com www.iaexim.com

Operating / Programming Section Mounting SectionOperation:

To move the Actuator in and out:

1-Press buttons 2 and 3 to make the actuator extend

2-Press buttons 1 and 2 to make the actuator retract

To Program Presets #1,2, and3:

3-Extend the actuator to where you would like the Preset #1 to be located.

4-Press and hold the Number 1 button for 5 seconds -The LED will flash to indicate setting has been learned

5-Extend or retract the actuator to where you would like Preset #2.

6-Press and hold the Number 2 button for 5 seconds -The LED will flash to indicate setting has been learned

7-Extend or retract the actuator to where you would like Preset #3.

8-Press and hold the Number 3 button for 5 seconds -The LED will flash to indicate setting has been learned

***The presets can be at any position throughout the stroke of the actuator. They do not have to be in order. Nor do they have to be programmed in order.***

The Main Control Unit and the Display must be mounted inside the vehicle to avoid moisture. Do not plug in the Main Control Unit until all wiring is complete.

The Display can be mounted in a variety of ways. Below you will find our suggested mounting options.

332211 3322115 seconds

11 3322 11 33225 seconds

11 22 33 11 22 335 seconds

11 3322 3311 332211 OR

11 3322 3311 332211 OR

11 3322 3311 332211 OR

11 3322 33

11 332211

OR

Use the supplied double-sided tape to mount the display to any flat surface.

Use the supplied mounting bolts for a more secure mounting option. The double-sided tape or the support bracket can be used as a template for marking and drilling the mounting holes.

The rear of the display panel is reversible so that the display harness can exit the top or the bottom of the display.

1- Remove the rear of the display by gently separating the front and rear halves. (The front and rear simply snap together and can be seperated by inserting a fingernail in between the front and rear halves).

2- Reverse the rear of the display.

3- Snap the Front and Rear halves together.

4 5

Operation:

To move the Actuator in and out:

1-Press buttons 2 and 3 to make the actuator extend

2-Press buttons 1 and 2 to make the actuator retract

To Program Presets #1,2, and3:

3-Extend the actuator to where you would like the Preset #1 to be located.

4-Press and hold the Number 1 button for 5 seconds -The LED will flash to indicate setting has been learned

5-Extend or retract the actuator to where you would like Preset #2.

6-Press and hold the Number 2 button for 5 seconds -The LED will flash to indicate setting has been learned

7-Extend or retract the actuator to where you would like Preset #3.

8-Press and hold the Number 3 button for 5 seconds -The LED will flash to indicate setting has been learned

***The presets can be at any position throughout the stroke of the actuator. They do not have to be in order. Nor do they have to be programmed in order.***

The Main Control Unit and the Display must be mounted inside the vehicle to avoid moisture. Do not plug in the Main Control Unit until all wiring is complete.

The Display can be mounted in a variety of ways. Below you will find our suggested mounting options.

332211 3322115 seconds

11 3322 11 33225 seconds

11 22 33 11 22 335 seconds

11 3322 3311 332211 OR

11 3322 3311 332211 OR

11 3322 3311 332211 OR

11 3322 33

11 332211

OR

Use the supplied double-sided tape to mount the display to any flat surface.

Use the supplied mounting bolts for a more secure mounting option. The double-sided tape or the support bracket can be used as a template for marking and drilling the mounting holes.

The rear of the display panel is reversible so that the display harness can exit the top or the bottom of the display.

1- Remove the rear of the display by gently separating the front and rear halves. (The front and rear simply snap together and can be seperated by inserting a fingernail in between the front and rear halves).

2- Reverse the rear of the display.

3- Snap the Front and Rear halves together.

Display:

Double-Sided Tape:

Mounting Bolts:

Reversible Rear Display Panel:

Mounting:

If you want to control itemswhen the ignition is ON.

If you want to raise/lower yourtrunk when the car if OFF.

If you want your trunk, runningboards, steering column, etc.to move automatically whenyou turn the ignition ON/OFF.

If you do not want automaticmovement when you turn thevehicle on and off.

www.iaexim.com www.iaexim.com

This unit has 3 Auxiliary negative inputs that can be used in conjunction with a keylessentry, alarm system, shaved door kit, etc. When a negative pulse is applied to any ofthese wires, the actuator will go to the specified preset.

**Optional inputs cannot set preset positions, or manually move the actuators. You WILLhave to use the display panel to configure the preset locations, at which point you mayremove the display.

Preset #1: White Wire Preset #2: Blue Wire Preset #3: Green Wire

Optional Features

6 3

DIP SWITCH FUNCTION ACTION REASON/EXAMPLES

ON

Wiring DiagramOptional Features

Green

BlackRed

WhiteYellow

Blue

RETAB TY

Ignition

Preset #1 Input Switch

Preset #2 Input Switch

Preset #3 Input Switch

BlackRed

PurpleWhiteYellow

11 3322DIP Switch Settings:

DIP switch #1: ON: The unit will operate only with Ignition. -The yellow ignition wire must receive +12vdc. OFF: The unit will operate only when Ignition is not present. -The yellow ignition wire is not connected.

DIP switch #2: ON: The unit will automatically return to Preset #2 with Ignition.-When the yellow ignition wire receives +12vdc the linear actuator will travel to Preset #2.-The LED will turn OFF after the preset is reached.The unit will automatically return to Preset #1 with loss of Ignition.-When +12vdc is removed from the yellow ignition wire the linear actuator will travel to Preset #1-The LED will remain ON after the preset is reached.The linear actuator cannot be controlled by the display.OFF: The linear actuator will remain in it's current position after an Ignition cycle.-When the key is turned OFF then back ON the linear actuator will remain at the same location.

Auxiliary Inputs:

This unit has 3 auxiliary negative inputs that can be used in conjunction with a keyless entry, alarm system, shaved door kit, etc. When a negative pulse is applied to any of these wires, the actuator will go to the specified preset.

Preset #1 White WirePreset #2 Blue WirePreset #3 Green Wire

6 3

OPTIONAL INPUTS

*SEE WIRING ON PAGE 6*

Operates only when ignition IS present.

Operates only when ignition is NOT present.

Auto return to preset #1with loss of ignition.

Auto return to preset #2with ignition.

Nothing happens withignition cycle.

The unit will operate onlywhen the yellow ignitionwire receives +12VDC

The unit will operate onlywhen the yellow ignitionwire is NOT receiving+12VDC

When +12VDC isremoved from the yellowignition wire the linearactuator will travel topreset #1.

-LED will turn off afterpreset has been reached.

When the yellow ignitionwire receives +12VDCthe linear actuator willtravel to preset #2.

-LED will remain on afterpreset is reached.

When the key is turnedon then off the linearactuator will remain atthe same location.

#1

#2

ON

OFF

ON

OFF

Wiring Diagram

ON

Auxiliary Inputs: