linia t26

32

The RIDI LINIA luminaire family

VL continuous lighting system: This continuous lighting system comes in two basic versions: • VLF, batten for single mounting • VL/VLS, continuous lighting system for predominantly continuous mounting, single mounting possible The following features are characteristic of both versions:

Batten VLF: This product series features a slimline luminaire body and a ceiling plate, making it ideally suited for directceiling and wall mounting as well as mounting as a single luminaire. Pendant mounting is possible using ac-cessories. By in-row ceiling or wall mounting of several luminaires, continuous lighting systems can becreated. The version VLF is only available with protection class IP 20.

Continuous lighting system VL/VLS: This product series comes with trunking (VLT) in a 1-3 lamp length version featuring open through wiringwith flexible take-off, and a gear tray (VLG/VLSG), which is electrically and mechanically connected to thetrunking by means of a patented adapter system. This luminaire system is ideally suited for the creation of modular and continuous lighting systems, alsoover long lengths. It is characterized by a simple quick-mounting system which cuts down on the time re-quired for installation. The special features of this system are the through wiring with facility for variabletake-off at any optional position, and the fact that trunking VLT can be optionally used in combination withgear tray VLG to create a continuous lighting system complying with protection class IP 20, or in combina-tion with gear tray VLGS… and seals (VLTVD) at the trunking joint to create a system complying with IP 54.

The luminaire colours: Luminaire version VLF is available as standard in white, while the VL/VLS version can be supplied in thestandard colours white and silver.

Fixing accessories:While the VLF battens are mounted using standard commercially available fixing materials directly on fixingsurfaces, and the LINIA DECO fixing kits are required for pendant mounting, for the VL continuous lightingsystem, system-specific fixing material is required both for pendant fixing and also direct mounting on fixingsurfaces. These fixing materials are listed and described in detail on the accessories pages.

Design configurations using junction points: In modern room interior architecture and design, the trend is away from a strictly rectangular arrangementof furnishings and fittings. This trend must be reflected in a similar degree of variability in design of thelighting system. For this reason, for the luminaires of the LINIA VL series, junction points are available as de-sign elements which permit different geometrical patterns to be created. The variability of the junction pointadapters also permits the suspension points to be specially adapted in line with circumstances on site.

Lighting engineering: A wide range of optical control elements is available for use with the luminaire series VLF, VL and VLS in theform of different reflectors, louvres and panels. These differ not only in terms of their finish quality and for-mal design, but also by the achievement of different photometric efficiency. This makes the luminaire sy-stem suitable for a wide range of different applications from industry through to administration. Informationon the configuration and application of the different optical control elements is provided in the product des-cription pages of the LINIA catalogue.

RIDI LINIA

33

Optical control and accessories 55-69

Modules 52-54VLM ...

Gear tray-optical control combinations 48-51VLSGR ..., VLML

Gear trays 43-47VLG, VLSG, VLSG ... FF, VLSG ... -SRD, VLG-I ...

Trunking accessories 40-42Accessories and junction points

Trunking 38-39VLT

Battens 36-37VLF, SML

Other photometric data 70-71

Contents RIDI LINIA

34

System overview RIDI LINIA

VLT ..

VLG 1.. VLG 2..

VTLV

Trunkingconnector Seal

Optical control/reflectors for mounting on gear trays or battens

Gear tray 1-lamp Gear tray 2-lamp Modules

TrunkingVLTVD

VLSG 1..VLSG 1.. FF VLSG 2.. FF

VLSG 2..

Trunking

Gear tray

Batten

Optical control/reflector

Lay-in reflector

Lay-in louvre / panel

VLR 1.. & 2..

VLWR 1.. & 2..

VLPS 1.. & 2..

VLOS 1.. & 2..

VLRAB 1.. & 2..

VLRAT 1.. & 2..

VLRAS 1..

VLAR 1.. & 2..

VLSRM 1.. & 2..

VLSRG 1.. & 2..

VLWR 1..

VLRL 1.. & 2..

VLRWF 1..

VLRIW 1..

VLM ... E14 VLM ... ST

VLM ... E27 VLM ... SD

VLM ... K11

VLM ... HW

VLM ... STS

(neededfor IP54)

VLRIB 1.. & 2..

VLRIT 1.. & 2..

VLRIS 1.. & 2..

VLRIH 1.. & 2..

VLTHA VLTHB VLTHS VLTHSD VLTHP KFWTLVSKTLVDHTLVTHTLV VLTWFS VLKH VLSPS SLKG TRA 008 ZRPK ZRP

Specifically for VLRWF 1..

Fixing accessories…

35

System overview RIDI LINIA

.. ETLV

Trunkingend cap

VLF 1..

Batten VLF 1-lamp

VLF 2..

Batten VLF 2-lamp

Gear tray-optical control combination(Facility for combination with LINIA system fixing accessories and trunking)

VLROW . VL-LBD 1.. VLDSM 1.. & 2..

VLDSG 1.. & 2..

VLML 1../2..

VLSGRS … FF

VLSGRS … SG FF

VLRF 1.. & 2..

VLRFAS 1..

VLBK..Dummy cover in plastic

VLB..

VLSBK..

VLSB..

Dummy cover in metal(Mounting of optical controls possible)

Article = For protection rating IP20

Article = For protection rating IP54 (including IP20)

1.. = 1-lamp

2.. = 2-lamp

PBLV VLTW

… for junctions

UKNUKNR-VL...

or or

UKNS UKNSB UKNA-VL

Components required for a continuous lighting system with n units 58 W.For the necessary optical control components, see under “Optical control and Accessories”.

3,07 2 1 - 2 - 2 24,61 3 - 1 2 - 3 36,15 4 2 - 2 1 3 47,69 5 1 1 2 1 4 59,22 6 - 2 2 1 4 6

10,76 7 2 1 2 2 5 712,30 8 1 2 2 2 5 813,83 9 - 3 2 2 6 915,37 10 2 2 2 3 7 1016,91 11 1 3 2 3 7 1118,44 12 - 4 2 3 8 1219,98 13 2 3 2 4 8 1321,52 14 1 4 2 4 9 1423,06 15 - 5 2 4 9 1524,59 16 2 4 2 5 10 16

26,13 17 1 5 2 5 10 1727,67 18 - 6 2 5 11 1829,20 19 2 5 2 6 12 1930,74 20 1 6 2 6 12 2032,28 21 - 7 2 6 13 2133,81 22 2 6 2 7 13 2235,35 23 1 7 2 7 14 2336,89 24 - 8 2 7 14 2438,43 25 2 7 2 8 15 2539,96 26 1 8 2 8 15 2641,50 27 - 9 2 8 16 2743,04 28 2 8 2 9 16 2844,57 29 1 9 2 9 17 2946,11 30 - 10 2 9 17 30

Lengthappr. [m]

Units Trunking582 583

Trunkingend cap

Trunkingconnector*

Pendant Gear tray Lengthappr. [m]

Units Trunking582 583

Trunkingend cap

Trunkingconnector*

Pendant Gear tray

* For IP 54 rated continuous lighting systems, VLTVD seals must be additionally ordered.

RIDI continuous lighting system ExpertThe continuous lighting system Expert can beused for simple, convenient constellation of con-tinuous lighting systems and their components.The required PC software can be downloadedfrom the Ridi website www.ridi.de.Intuitive menu prompting guides the user to thenecessary inputs. As a result, a bill of materialscontaining all the necessary components is pro-duced with calculation of the gross prices.

36

VLF 1..

VLF 2..

VLF158h [%] 93.9Phi_u [%] 74.0Phi_o [%] 26.0LITG_DIN B 31UTE 0.69H 0.24T

VLF258h [%] 94.9Phi_u [%] 66.0Phi_o [%] 34.0LITG_DIN B 32UTE 0.63G 0.32T

Batten VLF ...

Standalone or in combination with LINIA T-26 optical controllers for T26 lamps

VLF ...

Design: Rigid steel profiled luminaire housing made of sheet steel, coated white on both sides. End pieces in plas-tic complete with knock-outs for through wiring inside or outside of the luminaire. Profiled ceiling plate with an in-dented channel on the ceiling side for through wiring external to the luminaire, max. 3 x 1.5 mm² / diameter 8 mm.With magnetic ballasts (VVG) / electronic ballasts (EVG), 220 - 240 V, 50-60 Hz

Mounting: Simple, low-cost single-handed mounting of the luminaire ceiling plate using screws or similar (not in-cluded) through the keyhole-shaped hole in the plate. For pendant mounting, the LINIA DECO fixing kits can beused.The battens of the series VLF can be fitted with a large selection of reflectors, mirror reflectors and louvres.

Note: Luminaires with MM symbol and EVG are suitable for furniture mounting. Models without an index and mod-els with magnetic ballasts are not suitable.Internal through wiring can be prefitted on request.

Voltage: 230V/50Hz

Protection class: IP 20

Approvals:

1) MM symbol: No lateral spacing required between luminaire housing and adjacent surface. Models with magnetic ballasts (VG) cannot be used.3) MM symbol: 50 mm lateral spacing required between luminaire housing and adjacent surface. Models with magnetic ballasts (VG) cannot be used.4) Luminaires without VDE approval, as per VDE 0711/0875

Model LampsDimens. [mm]L1 A1 A2 K

Weight[kg]

magnetic ballastProd. code

electronic ballastProd. code

dimm. ballast (DALI)Prod. code

VLF 1181) 1xT26 18 W 619 530 55 22 1,4 1515945 1525945

VLF 1301) 1xT26 30 W 924 600 227 22/47 1,5 1515951 1525951

VLF 1361) 1xT26 36 W 1229 750 240 22/47 2,6 1515946 1525946 1535946

VLF 136-11) 4) 1xT26 36-1 W 999 600 240 22/47 2,4 1515952 1525952

VLF 1581) 1xT26 58 W 1529 1050 240 22/47 3,0 1515947 1525947 1535947

VLF 2183) 2xT26 18 W 619 530 55 22 2,1 1515948 1525948

VLF 2303) 2xT26 30 W 924 600 227 22/47 2,4 1515953 1525953

VLF 2363) 2xT26 36 W 1229 750 240 22/47 3,4 1515949 1525949 1535949

VLF 236-13) 2xT26 36-1 W 999 600 240 22/47 2,1 0525996

VLF 2583) 2xT26 58 W 1529 1050 240 22/47 5,2 1515950 1525950 1535950

IP20T26

1) 3) 4)

37

SML ...

SML ...

IP20T26

SML158h [%] 81.0Phi_u [%] 49.0Phi_o [%] 51.0LITG_DIN C 21UTE 0.40J 0.41T

Batten SML ... with diffuser

Diffuse beam, decorative luminaire, minimal direct glare.

Design: Angled housing made of rigid galvanized sheet steel ceiling spacer and support cam. Housing cover in an-gled sheet steel, white powder coated. End knock-outs for through-wiring inside the luminaire.With electronic ballasts (EVG), 220-240 V, 0/50-60 Hz

Diffuser: Semi-circular grooved diffuser made of white powder coated perforated steel. Clips onto the end cap foreasy change of lamp

Note: No other optical controllers can be adapted to fit on the SML batten

230V/50Hz

IP 20

Model LampsDimens. [mm]L1 L2 A1

Weight [kg]



SML 118 1xT26 18 W 650 625 490 1,4 B520173

SML 136 1xT26 36 W 1260 1235 1100 2,8 B520174 B530174

SML 158 1xT26 58 W 1560 1535 1400 3,6 B520175 B530175

Voltage:

Protection class:

Approvals:

38

VLT ...

VLT ...

VLT ... -5

VLT ... -7

VLT 361-5 1237 64 50 1,4 1500013

VLT 362-5 2474 64 50 2,9 1500016

VLT 363-5 3711 64 50 4,4 1500019

VLT 581-5 1537 64 50 1,8 1500022

VLT 582-5 3074 64 50 3,6 1500025

VLT 583-5 4611 64 50 5,4 1500028

VLT 361-5 SI 1237 64 50 1,4 1500013SI

VLT 362-5 SI 2474 64 50 2,9 1500016SI

VLT 363-5 SI 3711 64 50 4,4 1500019SI

VLT 581-5 SI 1537 64 50 1,8 1500022SI

VLT 582-5 SI 3074 64 50 3,6 1500025SI

VLT 583-5 SI 4611 64 50 5,4 1500028SI

VLT 361-7 1237 64 50 1,4 1500014

VLT 362-7 2474 64 50 2,9 1500017

VLT 363-7 3711 64 50 4,5 1500020

VLT 581-7 1537 64 50 1,8 1500023

VLT 582-7 3074 64 50 3,7 1500026

VLT 583-7 4611 64 50 5,6 1500029

VLT 361-7 SI 1237 64 50 1,4 1500014SI

VLT 362-7 SI 2474 64 50 2,9 1500017SI

VLT 363-7 SI 3711 64 50 4,5 1500020SI

VLT 581-7 SI 1537 64 50 1,8 1500023SI

VLT 582-7 SI 3074 64 50 3,7 1500026SI

VLT 583-7 SI 4611 64 50 5,6 1500029SI

Trunking VLT ...

VLT ... -5For use with continuous lighting systems complying with protection rating IP20 and IP54. Through wiring with flexi-ble take-off 5 x 2.5 mm². Continuous colour coding in blue. Trunking colour white.

VLT ... -5 SIFor use with continuous lighting systems complying with protection rating IP20 and IP54. Through wiring with flexi-ble take-off 5 x 2.5 mm². Continuous colour coding in blue. Trunking colour silver.

Design: Rigid, profiled trunking made of galvanized steel, white or silver synthetic resin coated on both sides. Thetrunking is available in a one, two or three-length version. Pre-punched knockouts are provided at the top at bothends for cable infeed

Through wiring: Open through wiring designed to permit variable take-off at any optional location. 5, 7 and 11-core versions available. The different versions are colour coded to simplify differentiation and correct mounting.

Mounting: The trunking elements can be mounted and assembled using fixing accessories. Junction points areavailable for creating continuous lighting system configurations. The trunking must be completely closed usinggear trays or dummy covers.

230V/50Hz

IP 20

Dimens. [mm] WeightModel L B H [kg] Art-Nr.


IP20 IP54T26

Voltage:

Protection class:

Approvals:

VLT ... -7For use with continuous lighting systems complying with protection rating IP20 and IP54. Through wiring with flexi-ble take-off 5 x 2.5 mm² and 2 x 1.5 mm² for control cables or emergency lighting circuit. Continuous colour cod-ing in purple. Trunking colour white.

VLT ... -7 SIFor use with continuous lighting systems complying with protection rating IP20 and IP54. Through wiring with flexi-ble take-off 5 x 2.5 mm² and 2 x 1.5 mm² for control cables or emergency lighting circuit. Continuous colour cod-ing in purple. Trunking colour silver.

39

VLT ... -11

VLT 361-11 1237 64 50 1,5 1500015

VLT 362-11 2474 64 50 3,1 1500018

VLT 363-11 3711 64 50 4,6 1500021

VLT 581-11 1537 64 50 1,9 1500024

VLT 582-11 3074 64 50 3,8 1500027

VLT 583-11 4611 64 50 5,8 1500030

VLT 361-11 SI 1237 64 50 1,5 1500015SI

VLT 362-11 SI 2474 64 50 3,1 1500018SI

VLT 363-11 SI 3711 64 50 4,6 1500021SI

VLT 581-11 SI 1537 64 50 1,9 1500024SI

VLT 582-11 SI 3074 64 50 3,8 1500027SI

VLT 583-11 SI 4611 64 50 5,8 1500030SI

Trunking VLT ...

VLT ... -11For use with continuous lighting systems complying with protection rating IP20 and IP54. Through wiring with flexi-ble take-off 5 x 2.5 mm² and 6 x 1.5 mm² for control cables and 2 separate emergency lighting circuits. Continu-ous colour coding in green. Trunking colour white.

VLT ... -11 SIFor use with continuous lighting systems complying with protection rating IP20 and IP54. Through wiring with flexi-ble take-off 5 x 2.5 mm² and 6 x 1.5 mm² for control cables and 2 separate emergency lighting circuits. Continu-ous colour coding in green. Trunking colour silver.


40

Trunking accessories

Rigid mains connector VLNE ... SFor rigid, solid core conductors up to max. 2.5 mm². Threedifferent models for 5, 7 and 11 (shown) core through wiring.Colour coding for the three versions. Includes bushing for insertion of cables in to the trunking or end cap.

VLNE-5S Colour coding blueVLNE-7S Colour coding purpleVLNE-11S Colour coding green

120704112070421207043

VLNE-5F Colour coding blueVLNE-7F Colour coding purpleVLNE-11F Colour coding green

120704712070481207049

Flexible mains connector VLNE ... FFor flexible, fine and stranded conductors up to max. 2.5 mm².Three different models for 5 (shown) 7 and 11-core throughwiring. Colour coding for the three versions. Includes bushingfor insertion of cables in to the trunking or end cap.

Trunking connector VLTV …Internal mechanical and electrical connection, toollessassembly with automatic PE conductor connection.

VLTV 1205790

Trunking connector VLTVA, VLTVA-AGExternal mechanical connection to comply with protec-tion rating IP 20. Enhances the mechanical strength of atrunking joint. Use in addition to internal trunking con-nector VLTV … .

VLTVA Colour whiteVLTVA-AG Colour silver (sim. to RAL 9006)

02065480206548AG

Trunking connector VLTV …Internal mechanical and electrical connection, toolless as-sembly with automatic PE conductor connection. Electricalconnector in three models for 5, 7 and 11 core throughwiring. Colour coding for the three versions.

VLTV-5 Colour coding blueVLTV-7 Colour coding purpleVLTV-11 Colour coding green

120704412070451207046

Seal VLTVDFor sealing the trunking connection to comply with pro-tection rating IP 54, 1 unit

Trunking end cap VLTE, VLTE SIEnd cap for trunking made of plastic. Round 20 mm dia.and oval 50 x 20 mm knockouts for cable infeed. As-sembly by plugging onto the trunking. Secure hold en-sured by spring steel clips. 1 pc.

VLTE Colour whiteVLTE SI Colour silver

02057910205791SI

VLTVD 1205789

Dummy cover VLBDummy element in profiled sheet steel, for mounting in-stead of a gear tray. Reflectors can be mounted on thedummy cover. Twist lock catch as for the gear tray. Tocomply with protection rating IP 20. Colour white.

VLB .36 Length 1237 mmVLB .58 Length 1537 mm

15000491500050

Clear mains cableA 1.5 m long clear mains cable is available for mainsconnection of wire pendant mounted luminaires. Otherlengths on request. 3 or 5-core. Cross section 0.75 or1.5 mm²ZAL 3x0,75/1,5M-TZAL 5x0,75/1,5M-TZAL 3x1,5/1,5M-TZAL 5x1,5/1,5M-T

0203579020358002079770207978

VLSBKD 1207191

Dummy cover VLSBDummy element in profiled sheet steel, for mounting in-stead of a gear tray. Reflectors can be mounted on thedummy cover. Twist lock catch as for the gear tray. Tocomply with protection rating IP 54. Colour white.

VLSB .36 Length 1237 mmVLSB .58 Length 1537 mm

15000511500052

Dummy cover VLB ... SIDummy element in profiled sheet steel, for mounting in-stead of a gear tray. Reflectors can be mounted on thedummy cover. Twist lock catch as for the gear tray. Tocomply with protection rating IP 20. Colour silver (similarto RAL 9006).VLB .36 SI Length 1237 mmVLB .58 SI Length 1537 mm

1500049SI1500050SI

Dummy cover VLBKDummy element in extruded plastic. Extruded profileclips into the trunking. For cutting to length as required.Protection rating IP 20. Colour white.

VLBK 361 Length 1237 mmVLBK 581 Length 1537 mmVLBK 583 Length 4611 mm

120518812051051205008

Dummy cover VLSBK, VLSBK ...-SIDummy element in extruded plastic. Extruded profile clipsinto the trunking. For cutting to length as required. Includesseals VLSBKD. To comply with protection rating IP 54.

VLSBK 361 Length 1227 mm Colour whiteVLSBK 361-SI Length 1227 mm Colour silverVLSBK 581 Length 1527 mm Colour whiteVLSBK 581-SI Length 1527 mm Colour silver

12071871207187SI

12071881207188SI

Dummy cover VLBK ... SIDummy element in extruded plastic. Extruded profileclips into the trunking. For cutting to length as required.Protection rating IP 20. Colour silver.

VLBK 361 SI Length 1237 mmVLBK 581 SI Length 1537 mmVLBK 583 SI Length 4611 mm

1205188SI1205105SI1205008SI

Seal IP54 VLSBKDSeal for mounting on dummy cover VLBK cut to lengthon site for continuous luminaires conforming to protec-tion rating IP 54 with variable spacing.

Chain suspension hanger VLTHAChain suspension hanger consisting of a robust steelspring clamp with height adjustable swing hook. Heightadjustment by means of a nut, over-tighten proof bymeans of grooves. Permissible load is 20 kg, 1 pc.

VLTHA 0205792

Chain suspension hanger VLTHBChain suspension hanger consisting of a robust steelspring clamp with height adjustable swing hooks (quickclamping). Quick fixing without tools. Permissible load20 kg, 1 pc.

VLTHB 0205685

Dummy cover VLSB ... SIDummy element in profiled sheet steel, for mounting in-stead of a gear tray. Reflectors can be mounted on thedummy cover. Twist lock catch as for the gear tray. Tocomply with protection rating IP 54. Colour silver (simi-lar to RAL 9006).VLSB .36 SI Length 1237 mmVLSB .58 SI Length 1537 mm

1500051SI1500052SI

41


Carabiner hook VLKHGalvanized carabiner hook made of steel. Permissibleload 20 kg. 1 pc.

VLKH 0205888

Tension hook VLSPSTension hook made of galvanised steel with hook. Per-missible load 20 kg, adjustment path 40 mm, 1 pc.

VLSPS 0205889

Hanger for ceiling mounting VLTHDRobust steel spring clamp for mounting of trunking tothe ceiling. Wide fixing slot for easy alignment compen-sation. Permissible load 30 kg. Max. screw diameter 6mm, 1 pc.

VLTHD 0205794

Chain suspension hanger VLTHDKFixing kit for horizontal suspension of asymmetrical re-flectors VLRFAS. Robust steel spring clamp for mountingof trunking on chains, with carabiner hook and fixingscrew, 1 pc.

VLTHDK 0205223

Trunking hanger VLTHPRobust steel spring clamp for fixing with pendant tubesdia. 13.5 mm. Permissible load 20 kg.1 pc.

VLTHP 0205793

Trunking hanger VLTHTRobust steel clamp with T bar clip for system ceilings.For fixing the trunking system to 24-26 mm T bars. Per-missible load 20 kg.

VLTHT 0205788

Trunking hanger VLTKSRobust spring clip for angled chain suspension from theceiling, with arm made of white coated steel. Permissi-ble load 20 kg. 1 pc.

VLTKS 0205886

Trunking hanger VLTWAngled wall and ceiling mounting bracket made of whitecoated steel. With robust spring clamp and safety screw. Permissibleload 20 kg. 1 pc.

VLTW 0205885

Chain TRA 008Galvanized chain made of steel. Permissible load 20 kg,by the metre (0.250 kg/m)

TRA 008 0200251

Quick fixing SLKBFor suspension of rows of luminaires on different sys-tem ceilings or other roof or ceiling constructions. Quickfixing for L and T supports, clamping range A = 3 – 7mm or 8 – 13 mm, with loop

SLKB 3-7SLKB 8-13

02009070200908

Quick fixing SLKBTR M6x16For fastening on visible bracket profiles in special-pur-pose ceiling systems 24 – 26 mm, with thread M6 x 16

SLKBT M6x16 0200912

Quick fixing SLKBTFor fastening on visible bracket profiles in special-pur-pose ceiling systems 24 – 6 mm, with loop

SLKBT 0200910

Quick fixing SLKBTR 0.8-2For fastening on plates (thickness 0.8 – 2.0 mm) onroofs and ceilings, with loop dia. 7.1 mm. Mounting holedia. 7 mm.

SLKBTR 0,8-2 0200909

Quick fixing for trapezoidal ceiling sectionsFor fastening on trapezoidal steel sections mounted onroofs and ceilings. Max. width 50 mm. Rail thicknessmin. 0.63 mm, mounting hole dia. 10 mm. With loopscrew M6.

SLKBTR M6 0201525

S chain link SLKGGalvanized S chain link made of steel. Permissible load20 kg. 1 pc.

SLKG 0200906

Ceiling fixing plate VLBPPlate made of galvanized steel. For fixing to ceilings.With 6 mm dia. loop for chain mounting. Max. screw dia.6 mm. 2 screws are required per plate. Permissible loadmax. 20 kg, 1 pc.

VLBP 0205887

Cable channel VLKLCable channel for mounting in trunking VLT … For cutting to length as required. Fixing clamps in springsteel. Length 4.6 m.

VLKL 0205775

Cable retainer VLTLACable retainer for fixing heavy cables to the top of thetrunking VLT ...2 x dia. 13 mm and 1 x dia. 7 mm cables possible, 1 pc.

VLTLA 0205760

42

Hanger VLTHSB-SIHanger for wire pendant mounting, consisting of robuststeel spring hoop with automatic wire clamp and steelwire 1.5 mm. Toolless height adjustment. Canopy semi-circular dia. 100 mm, H 50 mm, colour white, with lumi-naire connector block 3 x 2.5 mm². Colour silver.

VLTHSB-SI 0205923SI

Hanger VLTHSDHanger for wire pendant mounting, consisting of robuststeel spring hoop with automatic wire clamp and steelwire 1.5 mm. Toolless height adjustment. Ceiling fixingin metal, high-gloss nickel plated, dia. 16 mm, H 20 mm

VLTHSD 0205921

Chain hanger VLTWFKFixing kit for horizontal suspension of asymmetrical re-flectors VLRWF… on chains. Robust steel spring clipwith short arm in sheet steel, galvanized, carabiner hookand fixing screw, 1 pc.

VLTWFK 0205881

Wire hanger VLTWFSFixing kit for horizontal suspension of asymmetrical re-flectors VLRWF… on steel wires. Robust steel spring clipwith short arm in sheet steel, galvanized, automatic wireclamp and steel wire 1.5 mm. Toolless height adjust-ment. Wire end with integrated loop. 1 pc.

VLTWFS 0205880

Wire hanger VLTWFSDFixing kit for horizontal suspension of asymmetrical re-flectors VLRWF… on steel wires. Robust steel spring clipwith short arm in sheet steel, galvanized, automatic wireclamp and steel wire 1.5 mm. Toolless height adjust-ment. Ceiling fixing in metal, gloss nickel plated, dia. 16mm, H 20 mm. VLTWFSD 0206538

Chain hanger with canopy ZRPKShort tube piece and loop for chain fixing. Ceiling loopwith height adjustment by thread. Canopy made of plas-tic. Knock-out cable entry. Permissible load 20 kg Tube pendant 114 mm with canopy, 1 set = 1 pc.

ZRPK 0200483

Hanger VLTHSHanger for wire pendant mounting, consisting of a ro-bust steel spring hoop with automatic wire clamp andsteel wire, 1.5 m. Toolless height adjustment. Wire endwith integrated loop.

VLTHS 0205922

Hanger VLTHSBHanger for wire pendant mounting, consisting of robuststeel spring hoop with automatic wire clamp and steelwire 1.5 mm. Toolless height adjustment. Canopy semi-circular dia. 100 mm, H 50 mm, colour white, with lumi-naire connector block 3 x 2.5 mm². Colour white.

VLTHSB 0205923

Hanger VLTHSSHanger for wire pendant mounting on sloping ceilings,consisting of robust steel spring hoop with automaticwire clamp and steel wire 1.5 mm. Toolless height ad-justment. Ceiling fixing tapered in metal, nickel plated.

VLTHSS 0205920

Wire pendant VLTHSTHanger for wire pendant mounting, consisting of robuststeel spring hoop with wire clamp and steel wire 1.5mm. Toolless height adjustment. Ceiling fixing clamp forsystem ceilings with T profile 24 -26 mm. Permissibleload max. 10 kg.

VLTHST 0207943

Universal junction UKNRound junction for creating geometrical patterns in con-junction with junction adapter AKNA…Material die-cast metal with lids in steel. Dia. 120 mm, H 60 mm, 1 pc.

UKN Colour whiteUKN-AG Colour silver (sim. to RAL 9006)

02032530203253AG

Ceiling fixing kit UKNDCeiling fixing kit for universal junction UKN

UKND 0208105

Universal junction adapter UKNA-VLTAdapter for suspension in universal junction. Smallestangle between two luminaires is 60° (VLMRL=80°). Dis-tance from centre junction to trunking 250 mm. Materialdie cast metal, including through wiring 7 x 2.5 mm².

UKNA-VLT-7 Colour whiteUKNA-VLT-7-AG Colour silver (sim. to RAL 9006)

12072831207283AG

Tube pendant for universal junction UKNR-VLTube pendant for suspension of UKN. Ceiling loop withscrew height adjustment. Canopy in plastic, cableknockouts. Permissible load max. 20 kg.

UKNR-VL 050 Length 0,5 mUKNR-VL 100 Length 1,0 m

02050310205032

Wire pendant w.ceiling fixing UKNSInfinitely height adjustable wire pendent dia. 1.5 mm,length 1.5 m,with ceiling fixing (dia. 16 mm, H 20 mm)and automatic wire clamp adjustable without usingtools. 1 pc.

UKNS Length 1,5mUKNS 3M Length 3mUKNS 5M Length 5m

021095802159420215943

Wire pendant UKNSBInfinitely height adjustable wire pendent dia. 1.5 mm,with canopy in plastic (dia. 100 mm, H 50 mm) and au-tomatic wire clamp adjustable without using tools, glossnickel plated. Colour white, luminaire connector block 3x 2.5 mm² 1 pc.

UKNSB 0210959

Tube pendant ZRPHTube pendant dia. 13 mm with thread M13x1. Canopy inplastic (dia. 100 mm, H 50 mm). Colour white, with lu-minaire connector block 3 x 2.5 mm²

ZRPH 050ZRPH 100

02050200205021


43

VLG ...

VLG 1..

VLG 2..

VLG 136-5 1xT26 36 W 1237 1,4 1510001 1520001

VLG 158-5 1xT26 58 W 1537 1,7 1510002 1520002

VLG 236-5 2xT26 36 W 1237 0,9 1520003

VLG 258-5 2xT26 58 W 1537 1,1 1520004

VLG 136-7 DALI 1xT26 36 W 1237 0,7 1530001

VLG 158-7 DALI 1xT26 58 W 1537 0,9 1530002

VLG 158-7 ED1 1xT26 58 W 1537 1,5 1520002//374

VLG 158-7 ED3 1xT26 58 W 1537 1,6 1520002//375

VLG 158-7 Z 1xT26 58 W 1537 0,9 1520002//329

VLG 158-7 Z-UR 1xT26 58 W 1537 1,0 1520002//373

VLG 236-7 DALI 2xT26 36 W 1237 0,9 1530003

VLG 258-7 DALI 2xT26 58 W 1537 1,1 1530004

VLG 258-7 ED1 2xT26 58 W 1537 1,7 1520004//374

VLG 258-7 ED3 2xT26 58 W 1537 1,8 1520004//375

VLG 258-7 Z 2xT26 58 W 1537 1,1 1520004//329

VLG 258-7 Z-UR 2xT26 58 W 1537 1,2 1520004//373

VLG 158-11 DALI-ED1 1xT26 58 W 1537 2,1 1530002//378

VLG 158-11 ED1 1xT26 58 W 1537 2,1 1520002//378

VLG 158-11 ED3 1xT26 58 W 1537 1,6 1520002//379

VLG 158-11 Z 1xT26 58 W 1537 0,9 1520002//367

VLG 158-11 Z-DALI 1xT26 58 W 1537 0,9 1530002//367

VLG 158-11 Z-DALI-UR 1xT26 58 W 1537 1,0 1530002//366

VLG 158-11 Z-UR 1xT26 58 W 1537 1,0 1520002//366

VLG 258-11 DALI-ED1 2xT26 58 W 1537 1,7 1530004//378

VLG 258-11 ED1 2xT26 58 W 1537 1,7 1520004//378

VLG 258-11 ED3 2xT26 58 W 1537 1,8 1520004//379

VLG 258-11 Z 2xT26 58 W 1537 1,1 1520004//367

VLG 258-11 Z-DALI 2xT26 58 W 1537 1,1 1530004//367

VLG 258-11 Z-DALI-UR 2xT26 58 W 1537 1,2 1530004//366

VLG 258-11 Z-UR 2xT26 58 W 1537 1,2 1520004//366

Gear tray VLG

Design: Profiled, galvanized white coated steel gear tray housing. Plastic coated quick-release catches for mount-ing on trunking and for fixing optical control attachments. In conjunction with trunking VLT, to create modular orvariable continuous lighting systems complying to IP 20 protection rating. The gear trays can be mounted at anyoptional location on the trunking. Electrical adapters for flexible take-off of the through-wiring in the trunking.Phase selection by means of sliding contact. Coloured and optical coding for simple mounting. Mechanical codingprevents inadvertent polarity reversal. With electronic (EVG) ballast, 220 – 240 V, 0/50-60 Hz.

Note: D symbol with EVG design in conjunction with reflector closed to the top.

Design -5

Design -7

Design -11

230V/50Hz

IP 20

Model LampsDimens. [mm]L1

Weight[kg]




IP20T26

Voltage:

Protection class:

Approvals:

VLG ... -5Gear tray with blue colour coding for mounting in VLT-5, VLT-7 or VLT-11.The VVG versions are electrically and mechanically prepared for parallel power factor correction.

VLG ... -7Gear tray with purple colour coding for mounting in VLT-7 or VLT-11.

VLG ... -11Gear tray with green colour coding for mounting in VLT-11. Sliding contacts for selection of 2 separate emergencylighting circuits.

Additional designs:DALI: Dimmable DALI ballastED1: Gear tray with emergency lighting element and maintenance-free NiCd battery for maintained mode, 1

hour. With a 2-lamp gear tray, in emergency lighting mode 1 lamp is functional.ED3: Gear tray with emergency lighting element and maintenance-free NiCd battery for maintained mode, 3

hours. With a 2-lamp gear tray, in emergency lighting mode 1 lamp is functional.Z: Emergency lighting gear tray for central emergency power supply. With 1 lamp, in standby status, with 2

lamps 1 lamp in standby status, 1 lamp in continuous operation.Z-UR: Emergency lighting gear tray with switchover relay for central emergency power supply. With 1 lamp, in

continuous operation, with 2 lamps 1 lamp in continuous operation, 1 lamp for mains operation

44

VLSG 1..

VLSG 2..

VLSG 136-5 1xT26 36 W 1237 1,6 1510005 1520005

VLSG 158-5 1xT26 58 W 1537 1,9 1510006 1520006

VLSG 236-5 2xT26 36 W 1237 1,1 1520007

VLSG 258-5 2xT26 58 W 1537 1,3 1520008

VLSG 136-7 DALI 1xT26 36 W 1237 0,9 1530005

VLSG 158-7 DALI 1xT26 58 W 1537 1,1 1530006

VLSG 158-7 ED1 1xT26 58 W 1537 1,7 1520006//374

VLSG 158-7 ED3 1xT26 58 W 1537 1,8 1520006//375

VLSG 158-7 Z 1xT26 58 W 1537 1,1 1520006//329

VLSG 158-7 Z-UR 1xT26 58 W 1537 1,2 1520006//373

VLSG 236-7 DALI 2xT26 36 W 1237 1,1 1530007

VLSG 258-7 DALI 2xT26 58 W 1537 1,3 1530008

VLSG 258-7 ED1 2xT26 58 W 1537 1,9 1520008//374

VLSG 258-7 ED3 2xT26 58 W 1537 2,0 1520008//375

VLSG 258-7 Z 2xT26 58 W 1537 1,3 1520008//329

VLSG 258-7 Z-UR 2xT26 58 W 1537 1,4 1520008//373

VLSG 158-11 DALI-ED1 1xT26 58 W 1537 1,7 1530006//378

VLSG 158-11 ED1 1xT26 58 W 1537 1,7 1520006//378

VLSG 158-11 ED3 1xT26 58 W 1537 1,8 1520006//379

VLSG 158-11 Z 1xT26 58 W 1537 1,1 1520006//367

VLSG 158-11 Z-DALI 1xT26 58 W 1537 1,1 1530006//367

VLSG 158-11 Z-DALI-UR 1xT26 58 W 1537 1,2 1530006//366

VLSG 158-11 Z-UR 1xT26 58 W 1537 1,2 1520006//366

VLSG 258-11 DALI-ED1 2xT26 58 W 1537 1,9 1530008//378

VLSG 258-11 ED1 2xT26 58 W 1537 1,9 1520008//378

VLSG 258-11 ED3 2xT26 58 W 1537 2,0 1520008//379

VLSG 258-11 Z 2xT26 58 W 1537 1,3 1520008//367

VLSG 258-11 Z-DALI 2xT26 58 W 1537 1,3 1530008//367

VLSG 258-11 Z-DALI-UR 2xT26 58 W 1537 1,4 1530008//366

VLSG 258-11 Z-UR 2xT26 58 W 1537 1,4 1520008//366

Gear tray VLSG

Design: Profiled, galvanized white coated steel gear tray housing. Plastic coated quick-release catches for mount-ing on trunking and for fixing optical control attachments. In conjunction with trunking VLT, to create modular orvariable continuous lighting systems complying to IP 54 protection rating. The gear trays can be mounted at anyoptional location on the trunking. Electrical adapters for flexible take-off of the through-wiring in the trunking.Phase selection by means of sliding contact. Coloured and optical coding for simple mounting. Mechanical codingprevents inadvertent polarity reversal. With magnetic (VVG) or electronic (EVG) ballast, 220 – 240 V, 0/50-60 Hz.Lamp seals contain silicone.

Note: D symbol with EVG design in conjunction with reflector closed to the top.

Design -5

Design -7

Design -11

230V/50Hz

IP 54


Weight[kg]




VLSG ... -5Gear tray with blue colour coding for mounting in VLT-5, VLT-7 or VLT-11.The VVG versions are electrically and mechanically prepared for parallel power factor correction.

VLSG ... -7Gear tray with purple colour coding for mounting in VLT-7 or VLT-11.

VLSG ... -11Gear tray with green colour coding for mounting in VLT-11. Sliding contacts for selection of 2 separate emergencylighting circuits






IP54T26

VLSG ...

Voltage:

Protection class:

Approvals:

VLSG 1.. FF

VLSG 2.. FF

45

VLSG 136-5 FF 1xT26 36 W 1237 1,3 1520009

VLSG 158-5 FF 1xT26 58 W 1537 1,6 1520010

VLSG 236-5 FF 2xT26 36 W 1237 1,9 1520011

VLSG 258-5 FF 2xT26 58 W 1537 2,4 1520012

VLSG 136-7 FF-DALI 1xT26 36 W 1237 1,3 1530009

VLSG 158-7 FF-DALI 1xT26 58 W 1537 1,6 1530010

VLSG 158-7 FF-ED1 1xT26 58 W 1537 2,2 1520010//374

VLSG 158-7 FF-ED3 1xT26 58 W 1537 2,3 1520010//375

VLSG 158-7 FF-Z 1xT26 58 W 1537 1,6 1520010//329

VLSG 158-7 FF-Z-UR 1xT26 58 W 1537 1,7 1520010//373

VLSG 236-7 FF-DALI 2xT26 36 W 1237 1,9 1530011

VLSG 258-7 FF-DALI 2xT26 58 W 1537 2,4 1530012

VLSG 258-7 FF-ED1 2xT26 58 W 1537 3,0 1520012//374

VLSG 258-7 FF-ED3 2xT26 58 W 1537 3,1 1520012//375

VLSG 258-7 FF-Z 2xT26 58 W 1537 2,4 1520012//329

VLSG 258-7 FF-Z-UR 2xT26 58 W 1537 2,5 1520012//373

VLSG 158-11 FF-DALI-ED1 1xT26 58 W 1537 2,2 1530010//378

VLSG 158-11 FF-ED1 1xT26 58 W 1537 2,2 1520010//378

VLSG 158-11 FF-ED3 1xT26 58 W 1537 2,3 1520010//379

VLSG 158-11 FF-Z 1xT26 58 W 1537 1,6 1520010//367

VLSG 158-11 FF-Z-DALI 1xT26 58 W 1537 1,6 1530010//367

VLSG 158-11 FF-Z-DALI-UR 1xT26 58 W 1537 1,7 1530010//366

VLSG 158-11 FF-Z-UR 1xT26 58 W 1537 1,7 1520010//366

VLSG 258-11 FF-DALI-ED1 2xT26 58 W 1537 3,0 1530012//378

VLSG 258-11 FF-ED1 2xT26 58 W 1537 3,0 1520012//378

VLSG 258-11 FF-ED3 2xT26 58 W 1537 3,1 1520012//379

VLSG 258-11 FF-Z 2xT26 58 W 1537 2,4 1520012//367

VLSG 258-11 FF-Z-DALI 2xT26 58 W 1537 2,4 1530012//367

VLSG 258-11 FF-Z-DALI-UR 2xT26 58 W 1537 2,5 1530012//366

VLSG 258-11 FF-Z-UR 2xT26 58 W 1537 2,5 1520012//366

Gear tray VLSG ... FF

Design: Profiled, galvanized white coated steel gear tray housing. Plastic coated quick-release catches for mount-ing on trunking and for fixing optical control attachments. In conjunction with trunking VLT, to create modular orvariable continuous lighting systems complying to IP 54 protection rating. The gear trays can be mounted at anyoptional location on the trunking. Electrical adapters for flexible take-off of the through-wiring in the trunking.Phase selection by means of sliding contact. Coloured and optical coding for simple mounting. Mechanical codingprevents inadvertent polarity reversal. With electronic (EVG) ballast, 220 – 240 V, 0/50-60 Hz. Silicone-free design

Note: In compliance with the requirements of the D symbol according to the new standard and FF according to theold standard

Design -5

Design -7

Design -11

230V/50Hz

IP 54

VLSG ... -5 FFGear tray with round protection tube dia. 50 mm made of acrylic (PMMA)Gear tray with blue colour coding for mounting in VLT-5, VLT-7 or VLT-11.

VLSG ... -7 FFGear tray with round protection tube dia. 50 mm made of acrylic (PMMA)Gear tray with purple colour coding for mounting in VLT-7 or VLT-11.

VLSG ... -11 FFGear tray with round protection tube dia. 50 mm made of acrylic (PMMA)Gear tray with green colour coding for mounting in VLT-11. Sliding contacts for selection of 2 separate emergencylighting circuits.







Weight[kg]



IP54T26

VLSG ... FF

Voltage:

Protection class:

Approvals:

46

VLSG 1.. SRD

VLSG 2.. SRD

VLSG 136-5 SRD 1xT26 36 W 1237 1,7 1520017

VLSG 158-5 SRD 1xT26 58 W 1537 2,1 1520018

VLSG 236-5 SRD 2xT26 36 W 1237 2,7 1520019

VLSG 258-5 SRD 2xT26 58 W 1537 3,3 1520020

VLSG 136-7 SRD-DALI 1xT26 36 W 1237 1,7 1530017

VLSG 158-7 SRD-DALI 1xT26 58 W 1537 2,1 1530018

VLSG 158-7 SRD-ED1 1xT26 58 W 1537 2,7 1520018//374

VLSG 158-7 SRD-ED3 1xT26 58 W 1537 2,8 1520018//375

VLSG 158-7 SRD-Z 1xT26 58 W 1537 2,1 1520018//329

VLSG 158-7 SRD-Z-UR 1xT26 58 W 1537 2,2 1520018//373

VLSG 236-7 SRD-DALI 2xT26 36 W 1237 2,7 1530019

VLSG 258-7 SRD-DALI 2xT26 58 W 1537 3,3 1530020

VLSG 258-7 SRD-ED1 2xT26 58 W 1537 4,0 1520020//374

VLSG 258-7 SRD-ED3 2xT26 58 W 1537 4,1 1520020//375

VLSG 258-7 SRD-Z 2xT26 58 W 1537 3,3 1520020//329

VLSG 258-7 SRD-Z-UR 2xT26 58 W 1537 3,4 1520020//373

VLSG 158-11 SRD-DALI-ED1 1xT26 58 W 1537 2,7 1530018//378

VLSG 158-11 SRD-ED1 1xT26 58 W 1537 2,7 1520018//378

VLSG 158-11 SRD-ED3 1xT26 58 W 1537 2,8 1520018//379

VLSG 158-11 SRD-Z 1xT26 58 W 1537 2,1 1520018//367

VLSG 158-11 SRD-Z-DALI 1xT26 58 W 1537 2,1 1530018//367

VLSG 158-11 SRD-Z-DALI-UR 1xT26 58 W 1537 2,2 1530018//366

VLSG 158-11 SRD-Z-UR 1xT26 58 W 1537 2,2 1520018//366

VLSG 258-11 SRD-DALI-ED1 2xT26 58 W 1537 4,0 1530020//378

VLSG 258-11 SRD-ED1 2xT26 58 W 1537 4,0 1520020//378

VLSG 258-11 SRD-ED3 2xT26 58 W 1537 4,1 1520020//379

VLSG 258-11 SRD-Z 2xT26 58 W 1537 3,3 1520020//367

VLSG 258-11 SRD-Z-DALI 2xT26 58 W 1537 3,3 1530020//367

VLSG 258-11 SRD-Z-DALI-UR 2xT26 58 W 1537 3,4 1530020//366

VLSG 258-11 SRD-Z-UR 2xT26 58 W 1537 3,4 1520020//366

Gear tray VLSG ... SRD

Design: Profiled, galvanized white coated steel gear tray housing. Plastic coated quick-release catches for mount-ing on trunking and for fixing optical control attachments. In conjunction with trunking VLT, to create modular orvariable continuous lighting systems complying to IP 54 protection rating. The gear trays can be mounted at anyoptional location on the trunking. Electrical adapters for flexible take-off of the through-wiring in the trunking.Phase selection by means of sliding contact. Coloured and optical coding for simple mounting. Mechanical codingprevents inadvertent polarity reversal. With electronic (EVG) ballast, 220 – 240 V, 0/50-60 Hz. Silicone-free design.

Note: In compliance with the requirements of the D symbol according to the new standard and FF according to theold standard230V/50Hz

IP 54

Design -5

Design -7

Design -11

VLSG ... -5 SRDGear tray with triangular protection tube with internal reflector. No additional optical controller possible. With the 2-lamp version, the minimum angle between triangular protection tubes is 15°. Gear tray with blue colour coding for mounting in VLT-5, VLT-7 or VLT-11.

VLSG ... -7 SRDGear tray with triangular protection tube with internal reflector. No additional optical controller possible. With the 2-lamp version, the minimum angle between triangular protection tubes is 15°. Gear tray with purple colour coding for mounting in VLT-7 or VLT-11.

VLSG ... -11 SRDGear tray with triangular protection tube with internal reflector. No additional optical controller possible. With the 2-lamp version, the minimum angle between triangular protection tubes is 15°. Gear tray with green colour coding for mounting in VLT-11. Sliding contacts for selection of 2 separate emergencylighting circuits







Weight[kg]



VLSG ... SRD

IP54T26

Voltage:

Protection class:

Approvals:

47

VLG-I 1..

VLG-I 2..

VLG-I 136-5 PIR5 1xT26 36 W 1237 0,9 1520159

VLG-I 158-5 PIR5 1xT26 58 W 1537 1,1 1520160

VLG-I 236-5 PIR5 2xT26 36 W 1237 1,1 1520161

VLG-I 258-5 PIR5 2xT26 58 W 1537 1,3 1520162

Gear tray VLG-I ...

Design: Profiled, galvanized white coated steel gear tray housing. Plastic coated quick-release catches for mount-ing on trunking and for fixing optical control attachments. In conjunction with trunking VLT, to create modular orvariable continuous lighting systems complying to IP 20 protection rating. The gear trays can be mounted at anyoptional location on the trunking. Electrical adapters for flexible take-off of the through-wiring in the trunking.Phase selection by means of sliding contact. Coloured and optical coding for simple mounting. Mechanical codingprevents inadvertent polarity reversal. With electronic (EVG) ballast, 220 – 240 V, 0/50-60 Hz

Note: D symbol with EVG design in conjunction with reflector closed to the top.230V/50Hz

IP 20

acc. to VDE 0711/0875

Gear tray with movement sensor. Colour coding blue for mounting in VLT-5, VLT-7 or VLT-11.Movement sensor directly activates the gear, so that no additional control cables are required. Each gear trayworks independently. After the last detected movement, the lighting level remains at 100% for the run-on period of 5 minutes. After-wards it is dimmed to 10%. After a further 17 seconds, the lamp is switched off. The number of switching cyclesdoes not influence the service life of the lamp. Maximum mounting height 5 m. Other movement sensors with dif-ferent mounting heights can be supplied on request. Other run-on times can be pre-programmed ory on request.

t

Luminous flux

100%

10%

0,7 s 24 s 17 s5 min

First movement

Max. luminous flux

Last movement

Dimming starts

Min. luminous flux

Lamp is switched off


Weight[kg]


VLG-I ...

IP20T26

Voltage:

Protection class:

48

IP54T26

VLSGR158h [%] 63.2Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 40UTE 0.63D

VLSGR258h [%] 56.0Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 40UTE 0.56D

VLSGR 1..

VLSGR 2..

VLSGR ...

Gear tray – optical controller combination VLSGR ...

Design: Profiled, galvanized white coated steel gear tray housing. Plastic coated quick-release catches for mount-ing on trunking and for fixing the reflector. In conjunction with trunking VLT, to create modular or variable continu-ous lighting systems complying to IP 54 protection rating. The gear trays can be mounted at any optional locationthe trunking. Electrical adapters for flexible take-off of the through-wiring in the trunking. Phase selection bymeans of sliding contact. Coloured and optical coding for simple mounting. Mechanical coding prevents inadver-tent polarity reversal. With electronic (EVG) ballast, 220 – 240 V, 0/50-60 Hz. Steel reflector white powder coated with internal catches for fixing the panel frame. For use in rooms with a highdegree of soiling. Cover panel provides improved protection for the lamps and optical controllers. Longer mainte-nance intervals.Sealing material to ensure protection rating compliance silicone-free.Designs with ESG panel, reflectors, cross-blade louvres on request.

Note: In compliance with the requirements of the D symbol according to the new standard and FF according to theold standard

230V/50Hz

IP 54

acc. to VDE 0711/0875

VLSGR ... -5Gear tray with blue colour coding for mounting in VLT-5, VLT-7 or VLT-11.With highly transparent acrylic cover made of UV stabilized PMMA.

VLSGR ... -7Gear tray with purple colour coding for mounting in VLT-7 or VLT-11.With highly transparent acrylic cover made of UV stabilized PMMA.

VLSGR ... -11Gear tray with green colour coding for mounting in VLT-11. Sliding contacts for selection of 2 separate emergencylighting circuits.With highly transparent acrylic cover made of UV stabilized PMMA.






Voltage:

Protection class:

49

VLSGR 136-5 1xT26 36 W 1237 7,0 1520102

VLSGR 158-5 1xT26 58 W 1537 8,7 1520104

VLSGR 236-5 2xT26 36 W 1237 8,7 1520103

VLSGR 258-5 2xT26 58 W 1537 10,8 1520105

VLSGR 136-7 DALI 1xT26 36 W 1237 7,0 1530102

VLSGR 158-7 DALI 1xT26 58 W 1537 8,7 1530104

VLSGR 158-7 ED1 1xT26 58 W 1537 9,3 1520104//374

VLSGR 158-7 ED3 1xT26 58 W 1537 9,4 1520104//375

VLSGR 158-7 Z 1xT26 58 W 1537 8,7 1520104//329

VLSGR 158-7 Z-UR 1xT26 58 W 1537 8,8 1520104//373

VLSGR 236-7 DALI 2xT26 36 W 1237 8,7 1530103

VLSGR 258-7 DALI 2xT26 58 W 1537 10,8 1530105

VLSGR 258-7 ED1 2xT26 58 W 1537 11,4 1520105//374

VLSGR 258-7 ED3 2xT26 58 W 1537 11,5 1520105//375

VLSGR 258-7 Z 2xT26 58 W 1537 10,8 1520105//329

VLSGR 258-7 Z-UR 2xT26 58 W 1537 10,9 1520105//373

VLSGR 158-11 DALI-ED1 1xT26 58 W 1537 9,3 1530104//378

VLSGR 158-11 ED1 1xT26 58 W 1537 9,3 1520104//378

VLSGR 158-11 ED3 1xT26 58 W 1537 9,4 1520104//379

VLSGR 158-11 Z 1xT26 58 W 1537 8,7 1520104//367

VLSGR 158-11 Z-DALI 1xT26 58 W 1537 8,7 1530104//367

VLSGR 158-11 Z-DALI-UR 1xT26 58 W 1537 8,8 1530104//366

VLSGR 158-11 Z-UR 1xT26 58 W 1537 8,8 1520104//366

VLSGR 258-11 DALI-ED1 2xT26 58 W 1537 11,4 1530105//378

VLSGR 258-11 ED1 2xT26 58 W 1537 11,4 1520105//378

VLSGR 258-11 ED3 2xT26 58 W 1537 11,5 1520105//379

VLSGR 258-11 Z 2xT26 58 W 1537 10,8 1520105//367

VLSGR 258-11 Z-DALI 2xT26 58 W 1537 10,8 1530105//367

VLSGR 258-11 Z-DALI-UR 2xT26 58 W 1537 10,9 1530105//366

VLSGR 258-11 Z-UR 2xT26 58 W 1537 10,9 1520105//366

Gear tray – optical controller combination VLSGR ...

Design -5

Design -7

Design -11


Weight[kg]



50

VLSGR 1.. SG

VLSGR 2.. SG

VLSGR 136-5 SG 1xT26 36 W 1237 7,4 1520106

VLSGR 158-5 SG 1xT26 58 W 1537 9,2 1520108

VLSGR 236-5 SG 2xT26 36 W 1237 9,4 1520107

VLSGR 258-5 SG 2xT26 58 W 1537 11,6 1520109

VLSGR 136-7 SG-DALI 1xT26 36 W 1237 7,4 1530106

VLSGR 158-7 SG-DALI 1xT26 58 W 1537 9,2 1530108

VLSGR 158-7 SG-ED1 1xT26 58 W 1537 9,8 1520108//374

VLSGR 158-7 SG-ED3 1xT26 58 W 1537 9,9 1520108//375

VLSGR 158-7 SG-Z 1xT26 58 W 1537 9,2 1520108//329

VLSGR 158-7 SG-Z-UR 1xT26 58 W 1537 9,3 1520108//373

VLSGR 236-7 SG-DALI 2xT26 36 W 1237 9,4 1530107

VLSGR 258-7 SG-DALI 2xT26 58 W 1537 11,6 1530109

VLSGR 258-7 SG-ED1 2xT26 58 W 1537 12,2 1520109//374

VLSGR 258-7 SG-ED3 2xT26 58 W 1537 12,3 1520109//375

VLSGR 258-7 SG-Z 2xT26 58 W 1537 11,6 1520109//329

VLSGR 258-7 SG-Z-UR 2xT26 58 W 1537 11,7 1520109//373

VLSGR 158-11 SG-Z 1xT26 58 W 1537 9,2 1520108//367

VLSGR 158-11 SG-DALI-ED1 1xT26 58 W 1537 9,8 1530108//378

VLSGR 158-11 SG-ED1 1xT26 58 W 1537 9,8 1520108//378

VLSGR 158-11 SG-ED3 1xT26 58 W 1537 9,9 1520108//379

VLSGR 158-11 SG-Z-DALI 1xT26 58 W 1537 9,2 1530108//367

VLSGR 158-11 SG-Z-DALI-UR 1xT26 58 W 1537 9,3 1530108//366

VLSGR 158-11 SG-Z-UR 1xT26 58 W 1537 9,3 1520108//366

VLSGR 258-11 SG-DALI-ED1 2xT26 58 W 1537 12,2 1530109//378

VLSGR 258-11 SG-ED1 2xT26 58 W 1537 12,2 1520109//378

VLSGR 258-11 SG-ED3 2xT26 58 W 1537 12,3 1520109//379

VLSGR 258-11 SG-UR 2xT26 58 W 1537 11,7 1520109//366

VLSGR 258-11 SG-Z 2xT26 58 W 1537 11,6 1520109//367

VLSGR 258-11 SG-Z-DALI 2xT26 58 W 1537 11,6 1530109//367

VLSGR 258-11 SG-Z-DALI-UR 2xT26 58 W 1537 11,7 1530109//366

VLSGR ... SG

VLSGR158SGh [%] 60.3Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 50UTE 0.60C

VLSGR258SGh [%] 51.5Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 50UTE 0.52C

Gear tray – optical controller combination VLSGR ... SG

VLSGR ... -5 SGGear tray with blue colour coding for mounting in VLT-5, VLT-7 or VLT-11.With highly transparent acrylic cover made of UV stabilized PMMA and parabolic mirror louvre in specular anodizedsuper-purity aluminium.

VLSGR ... -7 SGGear tray with purple colour coding for mounting in VLT-7 or VLT-11.With highly transparent acrylic cover made of UV stabilized PMMA and parabolic mirror louvre in specular anodizedsuper-purity aluminium.

VLSGR ... -11 SGGear tray with green colour coding for mounting in VLT-11. Sliding contacts for selection of 2 separate emergencylighting circuits.With highly transparent acrylic cover made of UV stabilized PMMA and parabolic mirror louvre in specular anodizedsuper-purity aluminium.






Design -5

Design -7

Design -11


Weight[kg]



51

VLML ...

VLML ...

IP20T26

VLML158h [%] 66.2Phi_u [%] 97.0Phi_o [%] 3.0LITG_DIN A 41UTE 0.64E 0.02T

VLML258h [%] 62.4Phi_u [%] 97.0Phi_o [%] 3.0LITG_DIN A 41UTE 0.61E 0.02T

VLML 136-5 1xT26 36 W 1237 5,2 1520098

VLML 158-5 1xT26 58 W 1537 5,5 1520099

VLML 236-5 2xT26 36 W 1237 5,2 1520100

VLML 258-5 2xT26 58 W 1537 5,5 1520101

VLML 136-7 DALI 1xT26 36 W 1237 5,2 1530098

VLML 158-7 DALI 1xT26 58 W 1537 5,5 1530099

VLML 236-7 DALI 2xT26 36 W 1237 5,2 1530100

VLML 258-7 DALI 2xT26 58 W 1537 5,5 1530101

Gear tray – optical controller combination VLML…

Design: Profiled, galvanized white coated steel gear tray housing. Plastic coated quick-release catches for mount-ing on trunking and for fixing the reflector. In conjunction with trunking VLT, to create modular or variable continu-ous lighting systems complying to IP 20 protection rating. The gear trays can be mounted at any optional locationon the trunking. Electrical adapters for flexible take-off of the through-wiring in the trunking. Phase selection bymeans of sliding contact. Coloured and optical coding for simple mounting. Mechanical coding prevents inadver-tent polarity reversal. With electronic (EVG) ballast, 220 – 240 V, 0/50-60 Hz.

VLML: Parabolicaly styled secondary steel reflector, white powder coated with plastic end pieces for fixture of theperforated primary reflector, also white powder coated and with inserted opal plastic profile in UV-stable PMMA.Creates a pleasantly light lighting atmosphere in the room. No direct view of the lamp.

Voltage: 230V/50Hz

Protection class: IP 20

Approvals:

VLML ... -5Gear tray with blue colour coding for mounting in VLT-5, VLT-7 or VLT-11.

VLML ... -7Gear tray with purple colour coding for mounting in VLT-7 or VLT-11.

DALI: dimmable DALI ballast


Weight[kg]



52

VLM-E14 300 ...

VLM-E14 300 ...

VLM-E27 300 ...

VLM-E27 300 ...

IP20

IP20

VLM-E14 300-7 Z 1xIT 25 W 300 0,2 1500060//317

VLM-E14 300-11 Z 1xIT 25 W 300 0,2 1500060//382

VLM-E27 300-7 Z 1xA 60 W 300 0,2 1500061//383

VLM-E27 300-11 Z 1xA 60 W 300 0,2 1500061//384

VLM… modules

Design: Supplementary module VLM…, profiled, in galvanized white coated steel. Plastic coated quick-releasecatches for mounting on trunking and for fixing the optical controllers. Optical controllers can be supplied if re-quired on request.VLM… modules can be positioned variably between the gear trays VGL… . Electrical adapters for flexible take-offof the through-wiring in the trunking. Phase selection by means of sliding contact. Coloured and optical coding forsimple mounting. Mechanical coding prevents inadvertent polarity reversal.

Note: Supplementary modules VLM… generally comply with protection rating IP 20. the emergency lighting ver-sions can be used in systems complying to VDE 0108

230V/50Hz

IP 20

VLM-E27 300-7 ZEmergency lighting gear tray with E27 lampholder for central emergency power supply. Colour coding purple formounting in VLT-7.

VLM-E27 300-11 ZEmergency lighting gear tray with E27 lampholder for central emergency power supply. Colour coding green formounting in VLT-11. Sliding contacts for selection of 2 separate emergency circuits.

VLM-E14 300-7 ZEmergency lighting gear tray with E14 lampholder for central emergency power supply. Colour coding purple formounting in VLT-7.

VLM-E14 300-11 ZEmergency lighting gear tray with E14 lampholder for central emergency power supply. Colour coding green formounting in VLT-11. Sliding contacts for selection of 2 separate emergency circuits


Weight[kg] Prod. code



Voltage:

Protection class:

Approvals:

53

VLM-SD 300 ...

VLM-SD 300 ...

VLM-K11 600 ...

VLM-K11 600 ...

IP20

IP20

VLM-STS 600 ...

VLM-STS 600 ...

IP20

VLM-K11 600-7 EB1 1XTC-SEL 11 W 600 0,4 1520095//310

VLM-K11 600-7 EB3 1XTC-SEL 11 W 600 0,4 1520095//311

VLM-K11 600-7 Z 1XTC-SEL 11 W 600 0,4 1520095//329

VLM-K11 600-11 EB1 1XTC-SEL 11 W 600 0,4 1520095//351

VLM-K11 600-11 EB3 1XTC-SEL 11 W 600 0,4 1520095//352

VLM-K11 600-11 Z 1XTC-SEL 11 W 600 0,4 1520095//367

VLM-SD 300-5 300 0,2 1500058

VLM-STS 600-5 600 0,6 1500057

VLM… modules

VLM-SD 300-5Gear tray to accommodate spotlights for VLM-SD from the RIDI range. Colour coding blue for mounting VLT-5, VLT-7 or VLT-11

VLM-STS 600-5Gear tray with 3-phase lighting track to accommodate spotlights with 3-phase adapter. Colour coding blue formounting VLT-5, VLT-7 or VLT-11.All three phases are connected. Phase selection at the spotlight adapter. Maximum load 16A.


Weight[kg]






VLM-K11 600-7Emergency lighting gear tray for TC compact fluorescent lamp from 5 to 11 Watts. Colour coding purple for mount-ing in VLT-7.

VLM-K11 600-11Emergency lighting gear tray for TC compact fluorescent lamp from 5 to 11 Watts. Colour coding green for mount-ing in VLT-11. Sliding contacts for selection of 2 separate emergency circuits.

Additional designs:EB1: Gear tray with emergency lighting element and maintenance-free NiCd battery for non-maintained mode

1 hourEB3: Gear tray with emergency lighting element and maintenance-free NiCd battery for non-maintained mode

3 hoursZ: Gear tray for central emergency power supply in non-maintained mode.

54

VLM-LED-HW ...

VLM-LED-HW ...

IP20

VLM-LED-HW-B 600-7 ED1 LED 1,1 W 600 1,4 1520096//374


VLM-LED-HW-B 600-7 Z LED 1,1 W 600 1,3 1520096//329

VLM-LED-HW-B 600-7 Z-UR LED 1,1 W 600 1,4 1520096//373

VLM-LED-HW-C 600-7 ED1 LED 1,1 W 600 1,4 1520097//374


VLM-LED-HW-C 600-7 Z LED 1,1 W 600 1,3 1520097//329

VLM-LED-HW-C 600-7 Z-UR LED 1,1 W 600 1,4 1520097//373



VLM-LED-HW-B 600-11 Z LED 1,1 W 600 1,3 1520096//367

VLM-LED-HW-B 600-11 Z-UR LED 1,1 W 600 1,4 1520096//366



VLM-LED-HW-C 600-11 Z LED 1,1 W 600 1,3 1520097//367

VLM-LED-HW-C 600-11 Z-UR LED 1,1 W 600 1,4 1520097//366

VLM-ST 300 ...

VLM-ST 300 ...

IP20

VLM-ST 300-5 300 0,2 1500059

VLM… modules

VLM-LED-HW ... -7Emergency lighting gear tray with escape route sign type B or C. Colour coding purple for mounting in VLT-7. Es-cape route sign is illuminated from the edge by means of LEDs and made of UV-stabilized PMMA. Types ED1 andED3 are available on request with self-test / self test and monitoring functionality.

VLM-LED-HW ... -11Emergency lighting gear tray with escape route sign type B or C. Colour coding green for mounting in VLT-11. Slid-ing contacts for selection of 2 separate emergency lighting circuits. Escape route sign is illuminated from the edge by means of LEDs and made of UV-stabilized PMMA. Types ED1 andED3 are available on request with self-test / self test and monitoring functionality.

Additional designs:ED1: Gear tray with emergency lighting element and maintenance-free NiMH battery for maintained mode 1

hourED3: Gear tray with emergency lighting element and maintenance-free NiMH battery for maintained mode 3

hoursZ: Gear tray for central emergency power supply in non-maintained mode.Z-UR: Gear tray with switchover relay for central emergency power supply in maintained mode

VLM-ST 300-5Gear tray with prefitted earthed socket for connecting external appliances. Maximum load 16 A. Colour coding blue for mounting in VLT-5, VLT-7 or VLT-11.

The symbol type is contained in the product designation

Typ B

Typ C


Weight[kg]




55

IP20 IP54

IP20 IP54

VLR ...

VLG ... + VLR ... VLSG ... + VLR ...VLF ... + VLR ...

VLG158+VLRh [%] 76.8Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 40UTE 0.77D

VLG258+VLRh [%] 76.6Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 40UTE 0.77D

VLR ... SI

Reflector VLR ..., VLRL ... and accessories

Partially perforated profiled reflector made of white synthetic resin coated steel. Good reflection properties andnarrow-wide beam distribution. Indirect component through partial perforation at the sides.

For use in continuous lighting systems comprising• Batten VLFor• Trunking VLT• Gear tray VLG, VLSG1 reflector is required per continuous lighting systemgear tray

Dimens. [mm] WeightModel L1 B1 H1 [kg] Prod. code

VLR 136 1235 178 90 1,9 0205826

VLR 158 1535 178 90 2,4 0205827

VLR 236 1235 236 90 2,3 0205829

VLR 258 1535 236 90 2,8 0205830


VLR 136 SI 1235 178 90 1,9 0205826SI

VLR 158 SI 1535 178 90 2,4 0205827SI

VLR 236 SI 1235 236 90 2,3 0205829SI

VLR 258 SI 1535 236 90 2,8 0205830SI

Partially perforated profiled reflector made of synthetic resin coated steel, silver on the outside, white on the inside.Good reflection properties and narrow-wide beam distribution. Indirect component through partial perforation atthe sides.

56

VLRL ...IP20 IP54

VLG158+VLRLh [%] 77.1Phi_u [%] 94.0Phi_o [%] 6.0LITG_DIN A 41UTE 0.72D 0.05T

VLG258+VLRLh [%] 79.4Phi_u [%] 97.0Phi_o [%] 3.0LITG_DIN A 41UTE 0.77E 0.02T

VLRL ... SIIP20 IP54

VLRE 1 WhiteVLRE 1 SI White inside, silver outside VLRE 2 WhiteVLRE 2 SI White inside, silver outside

02057950205795SI

02057960205796SI

Reflector end cap VLREIn plastic. Simply clips into the end of the reflector. ..1 for 1-lamp version, ..2 for 2-lamp version1 unit

Reflector divider VLRZWIn steel, painted white. Clips into the reflector connector.To improve glare in the longitudinal direction for conti-nuous rows of luminaires1 unit

VLRZW 1VLRZW 2

02058670205868

VLRV 1 WhiteVLRV 1 SI White inside, silver outside VLRV 2 WhiteVLRV 2 SI White inside, silver outside

02058490205849SI

02058500205850SI

Reflector joining piece VLRVIn plastic, for connecting reflectors VLR when mountingin continuous rows. 2 connectors are required per re-flector joint. ..1 for 1-lamp version, ..2 for 2-lamp version, 1 unit

Reflector VLR ..., VLRL ... and accessories

Partially perforated profiled reflector made of white synthetic resin coated steel. Good reflection properties andnarrow-wide beam distribution. Indirect component through partial perforation at the sides.

Partially perforated profiled reflector made of synthetic resin coated steel, silver on the outside, white on the inside.Good reflection properties and narrow-wide beam distribution. Indirect component through partial perforation atthe sides.

Reflector accessories


VLRL 136 1235 178 90 1,7 0205123

VLRL 158 1535 178 90 2,1 0205124

VLRL 236 1235 236 90 2,0 0205129

VLRL 258 1535 236 90 2,5 0205130


VLRL 136 SI 1235 178 90 1,7 0205123SI

VLRL 158 SI 1535 178 90 2,1 0205124SI

VLRL 236 SI 1235 236 90 2,0 0205129SI

VLRL 258 SI 1535 236 90 2,5 0205130SI

57

VLRAB

VLRAT

VLRAS

IP20 IP54

VLG158+VLR+VLRABh [%] 85.1Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 50UTE 0.85C

VLG258+VLR+VLRABh [%] 83.2Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 40UTE 0.83D

IP20 IP54

VLG158+VLR+VLRATh [%] 87.6Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 50UTE 0.88C

VLG258+VLR+VLRATh [%] 83.8Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 50UTE 0.84C

IP20 IP54

VLG158+VLR+VLRASh [%] 83.8Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 50UTE 0.84C

Parabolic mirror reflector VLRAB, VLRAT, VLRAS

Parabolicaly formed wide beam reflector, made of high-reflectance, specular anodized super-purity aluminium.Precise optical control and high LOR.

Parabolicaly formed narrow beam reflector, made of high-reflectance, specular anodized super-purity aluminium.Precise optical control and high LOR.

Parabolicaly formed narrow beam reflector, made of high-reflectance, specular anodized super-purity aluminium.Precise optical control and high LOR.

The reflectors of series VLRAB, VLRAS and VLRAT are designed for insertion in steel reflectors VLR ...1 reflector is required per continuous lighting system gear tray

Dimensional drawing see VLR


VLRAB 136 1232 178 90 0,3 0205001

VLRAB 158 1532 178 90 0,4 0205002

VLRAB 236 1232 236 90 0,4 0205004

VLRAB 258 1532 236 90 0,5 0205005


VLRAT 136 1232 178 90 0,3 0205821

VLRAT 158 1532 178 90 0,4 0205822

VLRAT 236 1232 236 90 0,4 0205823

VLRAT 258 1532 236 90 0,5 0205824


VLRAS 136 1232 178 90 0,3 0205858

VLRAS 158 1532 178 90 0,4 0205859

58

IP20 IP54

VLG158+VLR+VLWRh [%] 65.0Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 40UTE 0.65D

VLG258+VLR+VLWRh [%] 66.3Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 40UTE 0.66D

VLWR

VLG ... + VLR ... + VLWR ... VLSG ... + VLR ... + VLWR ...VLF ... + VLR ... + VLWR ...

VLG158+VLR+VLRAS+VLWR

h [%] 75.7Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 50UTE 0.76C

VLG158+VLR+VLRAT+VLWR


IP20 IP54 VLWRL

Steel louvre VLWR for insertion in reflector VLR/VLRL.Can be used in conjunction with• Batten series VLFor• Trunking VLT• Gear tray VLG, VLSG• Reflector VLR, VLRL• Optionally parabolic mirror reflector VLRAB, VLRAT, VLRAS1 VLWR louvre is required per continuous lighting systemgear tray.Note: If installed in schools, nursery schools, changingrooms etc. always include springs (VLWRS-T26-0204001)when ordering.

Combination examples

Trunking VLT + gear tray VLG 158 + reflector VLR + inlay reflector VLRAS + inlay louvre VLWR

Trunking VLT + gear tray VLG 158 + reflector VLR + inlay reflector VLRAT + inlay louvre VLWR

Steel louvre VLWR, VLWRL

Cross-blade steel louvre, white powder coated. Hinges downwards and is secured against dropping down uninten-tionally by safety springs.

Cross-blade steel louvre, white powder coated. Cross blades perforated. Hinges downwards and is secured againstdropping down unintentionally by safety springs.


VLWR 136 1235 178 90 0,8 0205798

VLWR 158 1535 178 90 0,9 0205799

VLWR 236 1235 236 90 2,3 0205801

VLWR 258 1535 236 90 1,5 0205802


VLWRL 136 1235 178 90 0,6 0205132

VLWRL 158 1535 178 90 0,8 0205133

VLWRL 236 1235 236 90 0,8 0205135

VLWRL 258 1535 236 90 1,0 0205136

59

VLPS ...

VLG ... + VLR ... + VLPS/VLOS ... VLSG ... + VLR ... + VLPS/VLOS ...VLF ... + VLR ... + VLPS/VLOS ...

VLOS ...

IP20 IP54

VLG158+VLR+VLPSh [%] 51.1Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 50UTE 0.51C

VLG258+VLR+VLPSh [%] 58.8Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 40UTE 0.59D

IP20 IP54

VLG158+VLR+VLOSh [%] 51.2Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 40UTE 0.51D

VLG258+VLR+VLOSh [%] 65.6Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 40UTE 0.66D

Panel VLPS, VLOS

Prismatic panel with optically effective prisms made of UV-stabilized acrylic (PMMA)

Panels for insertion in reflector VLR/VLRL.Can be used in conjunction with • Batten series VLFor• Trunking VLT• Gear tray VLG, VLSG• Reflector VLR, VLRL• Optionally parabolic mirror reflector VLRAB, VLRAT,VLRAS1 panel is required per continuous lighting system geartray.With plug-on moulding for panel joints when mountingin continuous rows.

Opal panel made of UV-stabilized acrylic (PMMA).


VLPS 136 1235 178 90 0,3 0205861

VLPS 158 1535 178 90 0,4 0205862

VLPS 236 1235 236 90 1,0 0205864

VLPS 258 1535 236 90 1,2 0205865


VLOS 136 1235 178 90 0,3 0205924

VLOS 158 1535 178 90 0,4 0205925

VLOS 236 1235 236 90 1,0 0205926

VLOS 258 1535 236 90 1,2 0205927

60

VLAR

VLG .. + VLR.. + VLAR .. VLF .. + VLR .. + VLAR ..

IP20

VLG158+VLR+VLARh [%] 59.7Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 50UTE 0.60C

VLG258+VLR+VLARh [%] 59.3Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 50UTE 0.59C

VLG158+VLR+VLRAB+VLPS


VLG158+VLR+VLRAT+VLPS


VLG258+VLR+VLRAT+VLPS

h [%] 66.1Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 40UTE 0.66D

VLG258+VLR+VLRAB+VLPS


Aluminium mirror louvre VLAR

Mirror louvre in matt anodised super-purity aluminium with profiled cross blades.

Aluminium mirror louvre for insertion in reflectorVLR/VLRL.For use in conjunction with• Batten series VLFor• Trunking VLT• Gear tray VLG• Reflector VLR, VLRL1 louvre VLAR is required per continuous lighting systemelement.



VLAR 136 1235 178 90 0,8 0205832

VLAR 158 1535 178 90 1,0 0205833

VLAR 236 1235 236 90 0,8 0205835

VLAR 258 1535 236 90 1,0 0205836

Trunking VLT + gear tray VLG 158 + reflector VLR + inlay reflector VLRAB + inlay panel VLPS

Trunking VLT + gear tray VLG 158 + reflector VLR + inlay reflector VLRAT + inlay panel VLPS

Trunking VLT + gear tray VLG 258 + reflector VLR + inlay reflector VLRAB + inlay panel VLPS

Trunking VLT + gear tray VLG 258 + reflector VLR + inlay reflector VLRAT + inlay panel VLPS

61

VLSRM

VLG .. + VLR .. + VLSR. .. VLF .. + VLR .. + VLSR. ..

VLSRG

IP20

VLG158+VLR+VLSRMh [%] 67.2Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 50UTE 0.67C

VLG258+VLR+VLSRMh [%] 53.6Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 50UTE 0.54B

IP20

VLG158+VLR+VLSRGh [%] 73.2Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 60UTE 0.73B

VLG258+VLR+VLSRGh [%] 59.1Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 60UTE 0.59B

Parabolic mirror louvre VLSRM, VLSRG

Parabolic mirror louvre made of matt anodized super-purity aluminium

Parabolic mirror louvre for insertion in reflectorVLR/VLRL.Can be used on conjunction with• Batten series VLFor• Trunking VLT• Gear tray VLG• Reflector VLR, VLRL1 louvre VLSRM or VLSRG is required per continuouslighting system gear tray.Note: Louvre VLSRM/VLSRG ... clips into series VLR ...reflectors

Parabolic mirror louvre made of specular anodized super-purity aluminium


VLSRM 136 1235 178 90 0,4 0205838

VLSRM 158 1535 178 90 0,5 0205839

VLSRM 236 1235 236 90 0,6 0205841

VLSRM 258 1535 236 90 0,8 0205842


VLSRG 136 1235 178 90 0,4 0205844

VLSRG 158 1535 178 90 0,5 0205845

VLSRG 236 1235 236 90 0,6 0205847

VLSRG 258 1535 236 90 0,8 0205848

62

IP20

VLG158+VLRWFh [%] 81.9Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 30UTE 0.82E

VLRWF ...

VLG 1.. + VLRWF 1.. VLF 1.. + VLRWF 1..

IP20 VLRWF ... SI

VLG158+VLRWF+VLWRh [%] 75.0Phi_u [%] 99.0Phi_o [%] 1.0LITG_DIN A 40UTE 0.74E 0.01T

Wall washer reflector VLRWF ...

For use in conjunction with • Batten series VLFor• Trunking VLT• Gear tray VLG1 reflector is required per continuous lighting systemgear tray.Can only be used for 1-lamp gear tray.

Edged steel reflector, with welded-in ends, white powder coated. Inserted parabolic reflector made of matt an-odised high-reflectance super-purity aluminium. For this reflector, the louvres VLWR 1.. or VLWRL 1.. can be used.The asymmetric centre of gravity requires the use of special fixing kits VLTWF (see accessories).


VLRWF 136 1235 205 75 3,0 0205145

VLRWF 158 1535 205 75 3,7 0205146

Edged steel reflector, with welded-in ends, silver powder coated (similar to RAL 9006). Inserted parabolic reflectormade of high-reflectance matt anodized super-purity aluminium. For this reflector, louvres VLWR 1.. or VLWRL 1..can be used. The asymmetric centre of gravity requires the use of special fixing kits VLTWF (see accessories)


VLRWF 136 SI 1235 205 75 3,0 0205145SI

VLRWF 158 SI 1535 205 75 3,7 0205146SI


Trunking VLT + gear tray VLG 158 + reflector VLRWF + inlay louvre VLWR

63

VLRF

VLF ... + VLRF ...

VLG/VLSG ... + VLRF ...

VLF 1.. + VLRFAS 1..

VLG/VLSG 1.. + VLRFAS 1..

VLRFAS

IP20 IP54

VLG158+VLRFh [%] 82.1Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 40UTE 0.82E

VLG258+VLRFh [%] 81.8Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 40UTE 0.82E

IP20 IP54

VLG158+VLRFASh [%] 87.7Phi_u [%] 87.0Phi_o [%] 13.0LITG_DIN B 21UTE 0.76G 0.11T

Optical control reflector VLRF ..., VLRFAS ...

Edged flat reflector made of galvanized white synthetic resin coated steel. Symmetrical light distribution.

Edged reflector made of galvanized white synthetic resin coated steel. Asymmetrical light distribution. The asym-metric centre of gravity requires the use of special fixing kits VLTHDK (see accessories). Only 1-lamp gear trayscan be used

For use in conjunction with• Batten series VLFor• Trunking VLT• Gear tray VLG, VLSGNote: No other optical control elements or end caps can be fixed to these reflectors.1 reflector is required per continuous lighting system gear tray.


VLRF 118 636 172 60 0,7 1205811

VLRF 130 941 172 60 1,1 1205803

VLRF 136 1246 172 60 1,4 0205805

VLRF 136-1 1016 172 60 1,2 1205804

VLRF 158 1546 172 60 1,8 0205806

VLRF 218 636 230 60 0,9 1205765

VLRF 230 941 230 60 1,4 1205766

VLRF 236 1246 230 60 1,8 0205807

VLRF 236-1 1016 230 60 1,5 1205767

VLRF 258 1546 230 60 2,3 0205808


VLRFAS 136 1246 132 90 1,1 0205809

VLRFAS 158 1546 132 90 1,4 0205810

64

IP20

VLG158+VL-LBDh [%] 65.4Phi_u [%] 64.0Phi_o [%] 36.0LITG_DIN B 21UTE 0.42H 0.24T

VL-LBD

VLG 1.. + VL-LBD 1.. VLF 1.. + VL-LBD 1..

Perforated diffuser VL-LBD ...

Semi-circular diffuser made of white powder coated perforated steel. With retaining clips for mounting on T26lamps.

For use in conjunction with• Batten series VLFor• Trunking VLT• Gear tray VLG1 diffuser is required per continuous lighting systemgear tray.

Dimens. [mm] WeightModel L1 H1 [kg] Prod. code

VL-LBD 136 1234 48 0,4 0201628

VL-LBD 158 1534 48 0,5 0201629

65

VLROW

VLG 1.. + VLROW 1.. VLF 1.. + VLROW 1..

IP20

VLG158+VLROWh [%] 86.4Phi_u [%] 81.0Phi_o [%] 19.0LITG_DIN B 31UTE 0.70G 0.16T

VLG258+VLROWh [%] 85.6Phi_u [%] 80.0Phi_o [%] 20.0LITG_DIN B 31UTE 0.68G 0.17T

Oval cross-blade louvre VLROW ...

Oval-shaped blades made of steel connected to longitudinal blades, white powder coated. The louvre is hung fromthe top plate with the supplied reflector and can be hinged down for lamp changing. High LOR and good glare con-trol on the longitudinal axis of the lamp (C0 plane) the louvre can be used for a one-lamp and two-lamp gear tray.

Application: This attractive oval shaped white cross-blade louvre is particularly suited for lighting classrooms,lecture halls, corridors and hallways in which the main direction of lighting is mainly possible along the longitudinalaxis of the luminaire. Generates a bright, pleasant lighting atmosphere in the room.

For use in conjunction with• Batten series VLFor• Trunking VLT• Gear tray VLG1 VLROW louvre is required per continuous lighting sys-tem gear tray


VLROW.36 1235 236 90 2,1 0205785

VLROW.58 1535 236 90 2,7 0205786

66

VLDSM

VLDSM, VLDSG ...

VLDSG

IP20

VLG158+VLDSMh [%] 80.9Phi_u [%] 85.0Phi_o [%] 15.0LITG_DIN B 52UTE 0.69C 0.12T

VLG258+VLDSMh [%] 74.5Phi_u [%] 84.0Phi_o [%] 16.0LITG_DIN B 52UTE 0.63C 0.12T

IP20

VLG158+VLDSGh [%] 83.8Phi_u [%] 85.0Phi_o [%] 15.0LITG_DIN B 52UTE 0.71B 0.13T

VLG258+VLDSGh [%] 77.1Phi_u [%] 84.0Phi_o [%] 16.0LITG_DIN B 52UTE 0.65C 0.12T

Parabolic mirror louvre VLDSM ..., VLDSG ...

Decorative parabolic mirror louvre. Made of matt anodised high-reflectance super-purity aluminium. Diffuse lightcomponent on the ceiling.

For use in conjunction with• Batten series VLFor• Trunking VLT• Gear tray VLG1 louvre is required per continuous lighting system gear trayApplication: This parabolic mirror louvre with its technical decorative design is ideally suited for illuminating salesshowrooms and workplaces

Decorative parabolic mirror louvre. Made of specular anodised high-reflectance super-purity aluminium. Diffuselight component on the ceiling.



VLDSM 136 1235 164 82 0,6 0205870

VLDSM 158 1535 164 82 0,7 0205871

VLDSM 236 1235 204 82 0,8 0205874

VLDSM 258 1535 204 82 1,0 0205875


VLDSG 136 1235 164 82 0,6 0205872

VLDSG 158 1535 164 82 0,7 0205873

VLDSG 236 1235 204 82 0,8 0205876

VLDSG 258 1535 204 82 1,0 0205877

Trunking VLT + gear tray VLG 1.. + reflector VLDSG Trunking VLT + gear tray VLG 1.. + reflector VLDSM

67

VLRIB

VLG/VLSG ... + VLRIB ...

VLG/VLSG ... + VLRIT ...

VLF ... + VLRIT ...

VLF ... + VLRIB ...

VLRIT

IP20 IP54

VLG158+VLRIBh [%] 88.3Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 50UTE 0.88C

VLG258+VLRIBh [%] 89.5Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 40UTE 0.90D

IP20 IP54

VLG158+VLRITh [%] 91.4Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 50UTE 0.91C

VLG258+VLRITh [%] 89.3Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 40UTE 0.89D

Industrial reflectors VLRIB… wide beam, VLRIT … narrow beam

Edged industrial reflector made of very robust matt anodized high-reflectance super-purity aluminium. Wide-beamlight distribution and high LOR.

For use in conjunction with• Batten series VLFor• Trunking VLT• Gear tray VLG1 reflector is required per continuous lighting system gear tray.Overlapping reflectors. Consequently self-aligning and so requires no additional connecting elements.

Edged industrial reflector made of very robust matt anodized high-reflectance super-purity aluminium. Narrow-beam light distribution and high LOR


VLRIB 136 1246 190 82 0,4 0205812

VLRIB 158 1546 190 82 0,6 0205813

VLRIB 236 1246 255 82 0,6 0205814

VLRIB 258 1546 255 82 0,7 0205815


VLRIT 136 1246 200 70 0,4 0205816

VLRIT 158 1546 200 70 0,5 0205817

VLRIT 236 1246 265 70 0,5 0205818

VLRIT 258 1546 265 70 0,6 0205819

VLG/VLSG ... + VLRIH ...

VLF ... + VLRIH ...

VLRIHIP20 IP54

VLG158+VLRIHh [%] 88.4Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 50UTE 0.88C

VLG258+VLRIHh [%] 82.8Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 50UTE 0.83C

68

VLRIS

VLG/VLSG ... + VLRIS ...

VLF ... + VLRIS ...

IP20 IP54

VLG158+VLRISh [%] 92.1Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 40UTE 0.92D

VLG258+VLRISh [%] 90.2Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 40UTE 0.90D

Parabolic high-bay reflector made of highly specular high-reflectance super-purity aluminium for particularly nar-row beam light distribution. Very high LOR.

Industrial reflectors VLRIH…, high-bay reflector, VLRIS... inclined light distribution

Edged industrial reflector made of very robust matt anodised high-reflectance super-purity aluminium. Asymmetriclight distribution and high LOR.

For use in conjunction with• Batten series VLFor• Trunking VLT• Gear tray VLG VLSG 1.. (VLSG 2.. not possible)1 reflector is required for each continuous lighting system gear tray.Overlapping reflectors. Consequently self-aligning and so requires no additional connecting elements.


VLRIS 136 1246 225 82 0,5 0205992

VLRIS 158 1546 225 82 0,6 0205993

VLRIS 236 1246 285 82 0,6 0205958

VLRIS 258 1546 285 82 0,7 0205959


VLRIH 136 1246 216 104 0,5 0207940

VLRIH 158 1546 216 104 0,6 0207941

VLRIH 236 1246 304 130 0,7 0205137

VLRIH 258 1546 304 130 0,8 0205138

69

VLG/VLSG ... + VLRIW ...

VLRIWIP20 IP54

VLG158+VLRIWh [%] 91.0Phi_u [%] 97.0Phi_o [%] 3.0LITG_DIN A 30UTE 0.88G 0.03T

Industrial reflectors VLRIW ... wall washer reflector

Rounded wall washer reflector made of very robust matt anodized high-reflectance super-purity aluminium. Highlyasymmetrical light distribution. High LOR. Can only be used for 1-lamp gear trays.


VLRIW 136 1246 204 73 0,5 0202615

VLRIW 158 1546 204 73 0,6 0202616

70

VLG158+VLRL+VLAR

h [%] 64.1Phi_u [%] 98.0Phi_o [%] 2.0LITG_DIN A 51UTE 0.63C 0.01T

VLG258+VLRL+VLAR

h [%] 62.9Phi_u [%] 98.0Phi_o [%] 2.0LITG_DIN A 51UTE 0.62C 0.01T

VLG158+VLRL+VLOS

h [%] 52.0Phi_u [%] 88.0Phi_o [%] 12.0LITG_DIN B 41UTE 0.46E 0.06T

VLG158+VLRL+VLPS

h [%] 69.9Phi_u [%] 88.0Phi_o [%] 12.0LITG_DIN B 41UTE 0.62D 0.08T

VLG258+VLRL+VLPS

h [%] 65.2Phi_u [%] 92.0Phi_o [%] 8.0LITG_DIN A 42UTE 0.60D 0.05T

VLG158+VLRL+VLWR


VLG258+VLRL+VLWR


VLG158+VLR+VLRAB+VLWRh [%] 74.2Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 50UTE 0.74C

VLG258+VLR+VLRAB+VLWRh [%] 73.6Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 50UTE 0.74D

VLG258+VLR+VLRAS+VLWRh [%] 72.7Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 40UTE 0.73D

VLG258+VLR+VLRAT+VLWRh [%] 73.8Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 50UTE 0.74C

VLSG158+VLR


VLSG258+VLR

h [%] 78.8Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 40UTE 0.79E

VLSG158+VLR+VLOS


VLSG258+VLR+VLOS


VLSG158+VLR+VLPS


VLSG258+VLR+VLPS


VLSG158+VLR+VLRAB


VLSG258+VLR+VLRAB


VLSG158+VLR+VLRAB+VLPSh [%] 70.0Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 40UTE 0.70D

VLSG258+VLR+VLRAB+VLPSh [%] 68.6Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 40UTE 0.69D

VLSG158+VLR+VLRAB+VLWRh [%] 77.1Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 40UTE 0.77D

VLSG258+VLR+VLRAB+VLWRh [%] 78.9Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 40UTE 0.79D

VLSG158+VLR+VLRAS


VLSG258+VLR+VLRAS


Other photometric data

71

VLSG158+VLR+VLRAS+VLWRh [%] 76.8Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 50UTE 0.77C

VLSG258+VLR+VLRAS+VLWRh [%] 75.4Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 40UTE 0.75D

VLSG158+VLR+VLRAT


VLSG258+VLR+VLRAT


VLSG158+VLR+VLRAT+VLPSh [%] 71.5Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 40UTE 0.71D

VLSG258+VLR+VLRAT+VLPSh [%] 68.6Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 40UTE 0.69D

VLSG158+VLR+VLRAT+VLWRh [%] 79.4Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 50UTE 0.79C

VLSG258+VLR+VLRAT+VLWRh [%] 77.5Phi_u [%] 100.0Phi_o [%] 0.0LITG_DIN A 50UTE 0.78C

VLSG158+VLR+VLWR


VLSG258+VLR+VLWR


VLSG158+VLRF


VLSG258+VLRF


VLSG158+VLRFAS

h [%] 88.3Phi_u [%] 84.0Phi_o [%] 16.0LITG_DIN B 21UTE 0.74G 0.14T

VLSG158+VLRIB


VLSG258+VLRIB


VLSG158+VLRIS


VLSG258+VLRIS


VLSG158+VLRIT


VLSG258+VLRIT


VLSG158+VLRL

h [%] 82.0Phi_u [%] 93.0Phi_o [%] 7.0LITG_DIN A 41UTE 0.76E 0.06T

VLSG258+VLRL

h [%] 82.4Phi_u [%] 95.0Phi_o [%] 5.0LITG_DIN A 41UTE 0.78E 0.04T

VLSG158+VLRL+VLWR


VLSG258+VLRL+VLWR


VLSG258+VLRL+VLPS


VLSG158+VLROW

h [%] 83.5Phi_u [%] 80.0Phi_o [%] 20.0LITG_DIN B 31UTE 0.67G 0.17T

linia t26

Documents