lumiere - matallic epoxy flooring system e
TRANSCRIPT
-
8/14/2019 Lumiere - Matallic epoxy flooring system e
1/2
engineered to per orm
Architectural specifcations available upon request.
toll ree 1.866.835.6595 ax 1.866.629.4157 duraamen.com
lmieremetallic epoxy ooring system
Lmiere is a premium quality epoxy ooring system that is available in bright metallic fnishes. It has metallic integral pigment that gives
a variegated three-dimensional appearance. Typically it is coated with polyaspartic sealer that results in a high-per ormance, chemicaland abrasion resistant, easy to clean and virtually maintenance- ree ooring system.
the lmiere system requires the application o :a . Perdre E02, 100% solids epoxy primer
b . Lmiere , 100% solids metallic epoxy applied at 18-20mil thicknessc . Perdre P70 , 98% solids polyaspartic topcoat
usesShowrooms / Retail stores
Restaurants
Casinos
Entertainment centers
Malls and Super Stores
Dance oors
Tattoo parlors
Ca eterias,Ice cream parlors
Hair salons
O fce spaces / reception areas
Garage oors,Entertainment / Living rooms / Basements
eatures & beneftsExcellent clarity and three-dimensional appearance
Very high compressive strength, 11,000psi
Low odor during application, can be applied inoccupied spaces
Low viscosity; easy spreading and wetting properties
Superior adhesion and excellent abrasion and chemicalresistance
Available as a ast cure option or speedy application
available colors
bronze bright silver brass antique silver copper
-
8/14/2019 Lumiere - Matallic epoxy flooring system e
2/2
engineered to per orm
toll ree 1.866.835.6595 ax 1.866.629.4157 duraamen.com
lmieremetallic epoxy ooring system
lmiere system applicationThe application o the Lmiere system involves the ollowing steps:
1. application o primerThe substrate is prepared per the guidelines given in the Draamen technical
bulletin-1 and then one coat o the primer Perdre E02 is applied with a shortnap roller. The primer ensures ma ximum adhesion to the substrate and prevents
outgassing and air bubbling in the fnished system. Perdre E02 is a 100% solids, moisture-tolerant epoxy primer or concrete a nd
masonry sur aces. It combines the properties o water insensitivity and goodwetting properties. A ter the application o primer, it is allowed to cure or at least6-8 hours be ore the application o Lmiere body coat.
2. application o lmiere a . Mixing
I. Thoroughly mix each component separately prior to mixing with each other.
II. Mix 4 parts o A with 1 part o B by volume or three minutes with a low speedelectric drill mixing paddle.
III. Do not mix more material that can be used in 30 minutes.
b . ApplicationI. Pour material on the oor in a line and spread with a at/notched squeegee or
trowel to a coverage o 160 t 2 /gal. to achieve a thickness o 10-12mil.II. Back roll with a short nap roller to even the sur ace texture o
the coating.
III. Allow material to cure or 14-16 hours be ore applying the second coat. Twocoats are required unless a single coat is applied at least 18-20mil thick.
IV. Second coat (OPTIONAL): Mix and apply as be ore. I the second coat isback rolled, be aware that the roller pattern may be visible. While the materialis still wet, lightly mist sur ace with dispersing agent (acetone or Xylene, etc.)with a sprayer to cre ate special e ects. A carbon dioxide powered sprayeris a better option to avoid unwanted drips. Experimentation is necessar y todetermine how long to wait be ore spraying dispersing agent, based on such
actors as temperature, amount o solvent, type o solvent, etc. Spray toosoon and the epoxy will ow back to its original appearance. I sprayed toolate the Lmiere will not be a ected by the solvent mist.
V. The Lmiere is allowed to cure for at least 24 hours before the application of top coat.
3. application o topcoat a. Use Perdre P70 for sealing the Lmiere system.
Perdre P70 , 98% solids polyaspartic sealer is applied as a protective top coatover Lmiere body coat. Perdre P70 is a next generation aliphatic polyasparticpolyurea designed to provide high gloss, UV stable (non-yellowing), chemical andabrasion resistant protection. Perdre P70 has very low odor and can be appliedindoors in occupied areas.
technical dataTensile Strength (ASTMD-638)
8,500psi
Adhesion to Concrete(ACI 403)
350psi(100% concrete ailure)
Hardness (ASTM D-2240) 80 (Shore D)
Flexural Strength (ASTMD-790)
8,000psi
Compressive Strength(ASTM D-695)
11,000psi
Service Temperature 150F
Water absorption (ASTMD-670-73) 0.10% maximum
Viscosity @ 75F 750-1000cps
Mixing ratio 4 (Part A) : 1 (part B)
Solids Content 100% by volume
VOC
Gloss, 60F 100-110
Density 9.0-9.70lb/gal.
Pot li e 30-40min @ 75F
Dry to touch 10-14hours @ 75F
Recoat 14-16hours @ 75F
Light tra fc 24hours @ 75F
Full cure & Maximum
Resistance
5 days
Photos courtesy of Garage and Beyond