marine antennas summary - westradio.com.au · marine antennas summary zcg scalar, head office, 7...

MARINE ANTENNASSUMMARY

ZCG Scalar, Head Office, 7 Hall Street, PO Box 7, Lindenow, Victoria, 3865, AustraliaTelephone (03) 5157-1203, Fax (03) [email protected]

Section 6

HF, 2 to 30 MHz HM218/M, HM223/M Mast Mount or Side Mount HM300 10 metre Deck Mount HM212, HM215 Deck Mount27 MHz HM2800 “Coastguard” Base Station ZM108A Mast Mount or Side Mount ZM80, ZM108 Deck Mount BM6-27, BM8-27 Deck Mount ZM312H White Whip and BaseVHF, 156 to 162 MHz B20G, B20G-N Mast Mount or Side Mount CM156, B20G/D Deck Mount BM6-VHF, BM8-VHF Deck Mount ZM312V White Whip and BaseAIS, 161.9 to 162.1 MHz CM162AIS, CM162AIS-SS Deck MountUHF, 400 to 520 MHz CLU3SS Mast Mount MA675, MA400 Deck MountCellular Mobile Phone, NEXT G and GSM CM1600AM, CMG1600AM Mast Mount or Side Mount AN1600, DG1600 Deck Mount MADB Deck Mount BM6-DB, BM8-DB Deck MountAM/FM Radio B20G-N-AMFM Mast Mount AM80, B20G/D-AMFM Deck Mount MA1100 Deck Mount BM6-AM/FM, BM8-AM/FM Deck Mount ZM312B White Whip and BaseMarine Antenna MountsMast Mount AdaptorCable Ties and Tape

HM218/M and HM223/MHF Marine

Mast Mount or Side Mount


MARINEANTENNAS

Section 6

Updated 22 May 2011

Frequency Bandwidth2 – 30 MHz Requires ATU

Models HM218/M and HM223/M are suitable for all HF marine communications in the 2 to 30 MHz frequency range. These longer antennas offer top performance together with a two-piece light weight construction enabling easy dismantling and storage.The antennas are designed to couple with your HF radio transmitter via an Antenna Tuning Unit (ATU).

The two-piece white fibreglass radome is fully sealed and packed tight with closed cell foam to protect the internal braided copper radiator, prevent rattles and maximise service life in harsh marine conditions. The copper radiator terminates on a stainless steel stud above the mount tube, to which the 6 metre high voltage feed cable attaches. Mount tubes do not carry RF voltage.

To broaden your choice of mounting positions, both mast mount and side mount clamps are available.

For mounting to a mast, 2 x UAM180L galvanised steel parallel clamps are recommended for a round mast between 40 mm and 75 mm in diameter.

Side mounts are nylon and include ½"–BSW stainless steel fasteners. These allow easy mounting to the side of a wheelhouse or other vertical flat surface. Order NSM218 or NSM223 according to the antenna model. 2 nylon side mounts are necessary. Drill a 12.7 mm (½") diameter hole through the wall for the stainless steel bolt and then firmly secure each side mount in position.

Construction

SPECIFICATIONS

Frequency Range

Two-piece white fibreglass radome, copper radiator, chromed brass joining ferrules, stainless steel mount tube

HF 2 to 30 MHz with suitable Antenna Tuning Unit (ATU)

HM218/M

GainMax Input Power

2.1 dBi

Impedance (Nom.) ATU is required to match the antenna to 50 OhmsPolarisation Vertical

500 Watts PEP

Assembled Height 6.0 metresWeight 3.0 kg

MAST Mounting Clamps(not supplied)

2 x UAM180L heavy duty galvanised steel parallel clamps are recommended.Suit round mast between 40 mm and 75 mm in diameter.

Mount Tube DImensions

600 mm long x38 mm diameter

HM223/M

2.1 dBi1,400 Watts PEP

Tuning Tuning limits are determined by the ATUGrounding systems may also affect the ATU tune range

Vertical

Termination 6 metres of 20 kv single core cable fitted with a terminating lug for antenna terminal supplied

8.1 metres8.0 kg

Shipped Length 3.6 metres 4.0 metresShipped Weight 5.0 kg 12.0 kg


SIDE Mounting Clamps(not supplied)

2 x NSM218will suit the 38 mm mount tube

2 x NSM223will suit the 50 mm mount tube

For the replacement fibreglass Top section only

Order HM218/TP Order HM223/TPNylon Side Mount

Projected Area 0.136 metres2

Wind Load 160 kph 16.46 kg, 0.163 kN0.215 metres2

25.99 kg, 0.255 kN

Since tuning limits are determined by the ATU, clients contemplating purchase of these antennas should verify that their ATU specification will load the given length of radiator for the chosen model at the lowest frequency desired.

HM300HF Marine Radio

10 metre Deck Mount

Frequency


MARINEANTENNAS

Section 6

Updated 19 January 2012

Bandwidth2 – 30 MHz Requires ATU

HM300 is a 10 metre tall free standing marine HF radio deck mount antenna specifically designed for larger vessels. This model delivers outstanding performance, is very durable and accepts high input power up to 2,000 watts PEP.The antenna couples with a HF radio transmitter via an Antenna Tuning Unit.

The sturdy fibreglass radome is a three piece construction with each section joined with stainless steel ferrules. Each radome is fully sealed and packed tight with closed cell foam to protect the internal braided copper radiators, prevent rattles and maximise service life in harsh marine conditions.

The radome tip has a corona ball to prevent high voltage discharge into the atmosphere. The antenna butt is bonded to a short piece of stainless steel tube.

The deck mount base assembly is available to order separately if required. Constructed from stainless steel, this very sturdy deck mount plate is 300 mm in diameter and 12 mm thick, as pictured below. The vertical mount tube is welded to the steel plate. There are 4 holes in the plate for securing the base to the deck using stainless steel bolts, washers and nuts. Termination is via a bolt in the base to which the 6 metre single core 20 kV antenna feed cable attaches.

SPECIFICATIONS HM300

Three piece white fibreglass radome, copper radiators, stainless steel joining ferrules

Tuning limits are determined by the ATU used. Grounding systems may also affect the ATU tune range.

6 metres of 20 kv single core cable fitted with a lug for antenna terminal supplied

2,000 Watts PEP

HF Radio 2 to 30 MHz with suitable ATU

2.1 dBi

Antenna Tuning Unit is requiredto match the antenna to 50 Ohms

Construction

Tuning

Termination

Maximum Power

Frequency Range

Gain

Impedance (Nom)

Polarisation VerticalHeight 10 metresWeight 24 kgMount Tube 60 mm diameter x 4 mm stainless steelDeck Mount Base Assembly, available to order separately

Order Code : 1429300 mm diameter x 12 mm stainless steel,4 holes for securing the base to the deck

Shipping Length 4 metresShipping Weight 42 kg

Advice to customers :To achieve best performance, the marine HF radio antenna must be mounted as far away from other antennas and metallic objects as possible to avoid interference and distortion of the radiation pattern. Also, a good earth system is the essential key to achieving the optimum transmit and receive performance. The HF radio antenna must be isolated from the vessel’s earth system. The antenna feeder cable attaches to your Antenna Tuning Unit, and it is the ATU which must be connected to the vessel’s earth system. Refer to the installation instructions which came with your ATU.The vertical radiation pattern for HF radio antennas is largely influenced by the size, shape and nature of the ground plane under the antenna. Symmetrical, balanced, as well as low resistance earthing is needed for a good omnidirectional radiation pattern. The length and placement of the feedline also has a large effect on pattern formation, with modelling indicating a long feedline at right angles to the antenna causes the pattern to vary greatly from omnidirectional.

1429Stainless Steel

Deck Mount Base available to order

separately

HM212 and HM215HF Marine

Deck Mount


MARINEANTENNAS

Section 6

Updated 22 May 2011

Frequency Bandwidth2 – 30 MHz Requires ATU

The HM212 and HM215 deck mount models are suitable for all HF marine communications in the 2 to 30 MHz frequency range.

These antennas are designed to couple with your HF radio transmitter via an Antenna Tuning Unit (ATU).

The single piece fibreglass radome is fully sealed and packed tight with closed cell foam to protect the internal braided copper radiator, prevent rattles and maximise service life in harsh marine conditions.

The copper radiator terminates via 5 metres of high voltage (20 kV) feed cable side exiting from the chromed brass mount ferrule.

Both models come complete with our highest quality fully stainless steel MM2 folding deck mount. This base folds down in two directions and also swivels in the opposite plane by loosening the stainless steel pivot bolt. This versatility allows the antenna to be mounted in a variety of positions on any flat surface and at any angle using four screws or bolts.

The antenna must be in a vertical position for optimum performance and can be folded down when not required.

Construction

SPECIFICATIONS

Frequency Range

Single piece white fibreglass tapered radome, copper radiator, chromed brass ferrule, 1"–14 UNS thread

HF 2 to 30 MHz with suitable Antenna Tuning Unit (ATU)

HM212

GainMax Input Power

2.1 dBi

Impedance (Nom.) ATU is required to match the antenna to 50 OhmsPolarisation Vertical

250 Watts PEP

Height (inc mount) 3.7 metresWeight (inc mount) 2.0 kg

Deck MountSupplied

The MM2 stainless steel folding deck mount supplied can be secured to any flat surface horizontal or vertical at any angle using 4 screws or bolts

HM215

2.1 dBi250 Watts PEP

Tuning Tuning limits are determined by the ATUGrounding systems may also affect the ATU tune range

Vertical

Termination 5 metres of 20 kv single core cable side exits from the chromed brass mount ferrule

4.5 metres3.5 kg

Shipped Length 3.9 metres 4.7 metresShipped Weight 4.0 kg 5.0 kg

MM2 stainless steel folding deck mount

Installation Advice :A good earth system is the essential key to achieving the optimum transmit and receive performance. The HF antenna must be isolated from the vessel’s earth system. The antenna feeder cable attaches to your ATU, and it is the Antenna Tuning Unit which must be connected to the vessel’s earth system. Refer to the installation instructions which came with your ATU.The vertical radiation pattern for this HF radio antenna is largely influenced by the size, shape and nature of the ground plane under the antenna. Symmetrical, balanced, as well as low resistance earthing is needed for a good omnidirectional radiation pattern.The length and placement of the feedline also has a large effect on pattern formation, with modelling indicating a long feedline at right angles to the antenna causes the pattern to vary greatly from omnidirectional.Keep all leads as short as posible and joints in the earth system fully soldered. Earthing system problems may also cause the DC feed wiring to become an active radiator.

Since tuning limits are determined by the ATU, clients contemplating purchase of these antennas should verify that their ATU specification will load the given length of radiator for the chosen model at the lowest frequency desired.

HM2800 “Coastguard”27 MHz MarineBase Station


MARINEANTENNAS

Section 6

Updated 18 February 2011

Frequency27.680 – 27.980 MHz

Built to full commercial specifications, the HM2800 “Coastguard” 27 MHz marine base station antenna will survive long term in the most severe weather conditions and hostile environments.

Standing 6.2 metres tall, the brass and cable internals are fully sealed inside a strong white fibreglass radome and stainless steel mount tube.

The 1 metre cable tail is terminated with an N-Female connector rated for up to 50 watts input power.

Mast mounting clamps, feeder cable, connectors and cable fittings are available separately to complete the installation.

SPECIFICATIONS HM2800

Frequency

Max Input PowerImpedance

Tuning

Polarisation

Cable Tail

HeightWeight

Mounting Clamps(Not Supplied,order separate)

Gain

Construction

27.680 – 27.980 MHz

2.1 dBi50 Watts50 Ohms

Factory

Vertical

1 metre of RG213

6.2 metres7 kg

2 x UAM180L heavy duty galvanised steel parallel clamps are recommended.Suit round mast between 40 mm and 75 mm in diameter.

White fibreglass radome, brass and cable internals, stainless steel mount tube

Return Loss, VSWR Better than -15 dB, < 1.5:1

H-Plane 360O Omnidirectional

Connector N-Female fitted to the cable

Mount Tube 500 mm long x 50 mm diameter

ZM108A27.88 MHz Marine Radio



MARINEANTENNAS

Section 6

Updated 10 August 2011

ZM108A is a ground independent mast mount antenna for 27.88 MHz marine radio communications. This model can also be side mounted from a wheelhouse or any other flat vertical surface.

The white fibreglass radome and stainless steel mount tube stands 2.8 metres tall. The internal radiator is copper and the end fed half wave design provides excellent performance.

An N-Female connector is located at the base of the stainless steel mount tube. The maximum input power is 25 watts.

All components used are of the highest quality to ensure long term survival in the harsh marine environment. The antenna will deliver reliable performance for many years.

Mounting clamps, feeder cable, connectors, cable ties and tape are available separately to complete the installation.

SPECIFICATIONS ZM108A

Frequency


Tuning

Polarisation

HeightWeight

MAST Mounting Clamps(Not supplied,order separate)

Gain

Construction

27.88 MHz Marine Radio


Factory

Vertical

2.8 metres1.6 kg

2 x EB1SS stainless steel parallel clamps are recommended.Suit round mast between 20 mm and 50 mm in diameter.

Single piece white fibreglass tapered radome, copper radiator, stainless steel mount tube

VSWR Better than 1.5:1

H-Plane 360O OmnidirectionalConnector N-Female at base of mount tube


SIDE Mounting Clamps(Not supplied,order separate)

2 x NSM-B20M nylon side mounts are recommended to suit the 20 mm diameter mount tube.

EB1SSstainless steel parallel mast

clamps

Constructed from nylon with stainless steel bolts and washers, Nylon Side Mounts are specifically designed to mount a marine antenna to the side of a vessel’s wheel house or other flat vertical structure.

Drill a 12.7 mm (½") diameter hole through the vertical surface for the stainless steel bolt. Then tighten the bolt to firmly secure the side mount in position.

Using two (2) of these nylon side mounts, the antenna mount tube is held tight by the 8 mm stainless steel clamp bolt.

NSM-B20M

ZM80 and ZM10827.88 MHz Marine Radio

Deck Mount


MARINEANTENNAS

Section 6


Suitable for 27.88 MHz marine radio communications, these ground independent deck mount antennas are a single piece construction. The internal radiator is copper and the end fed half wave design provides excellent performance.

The ZM80 model stands 2.2 metres tall and ZM108 is 2.5 metres. These antennas match the height and appearance of other deck mount models in the marine range.

4.5 metres of RG58 stranded cable side exits from the chromed brass ferrule. Cut the cable to the shortest length necessary prior to fitting the UHF Male solder connector supplied.

All components used are of the highest quality to ensure long term survival in the harsh marine environment. These antennas will deliver reliable performance for many years.

The MM1 folding deck mount supplied as standard is constructed from toughened plastic. This base folds down in two directions and also swivels in the opposite plane by loosening the stainless steel pivot bolt. This versatility allows the antenna to be mounted in a variety of positions on any flat surface and at any angle using four screws or bolts.

For those who prefer the ultimate in quality, durability and strength, the MM2 folding deck mount is constructed entirely from stainless steel. To order either antenna with the stainless steel MM2 deck mount, simply add the letters ‘SS’ to the Order Code.

Feeder cable, connectors, cable ties and tape are available separately to complete the installation.

UHF Male solder connector supplied, not fitted. (Also known as PL259.)

The MM1 folding deck mount supplied as standard is constructed from toughened plastic.

For those who prefer the ultimate in quality, durability and strength, the MM2 folding deck mount is constructed entirely from stainless steel.

Construction

SPECIFICATIONS

Frequency

Single piece white fibreglass tapered radome, internal copper radiator, chromed brass ferrule with 1"–14 UNS female thread


ZM80, ZM80SS

GainMax Input Power

2.1 dBi

Impedance 50 OhmsPolarisation Vertical

25 Watts

ZM108, ZM108SS

2.1 dBi25 Watts

Tuning Factory

VerticalH-Plane 360O Omnidirectional

FactoryVSWR Better than 1.5:1 Better than 1.5:1

50 Ohms

360O OmnidirectionalCable 4.5 metres of RG58 stranded cable side exits from the ferruleConnector UHF Male solder connector supplied, not fitted (PL259)Height (inc mount) 2.2 metres 2.5 metresWeight (inc mount) 1 kg, 1.75 kg 1.1 kg, 1.85 kg

Folding Deck Mount Base Supplied

MM1 with ZM80MM2 with ZM80SS

MM1 with ZM108MM2 with ZM108SS


BM6-27 and BM8-2727.88 MHz Marine Radio

Deck Mount


MARINEANTENNAS

Section 6


Ground independent and factory tuned for 27.88 MHz marine radio communications, these Base Model deck mount antennas are a perfect match in both height and appearance to other ZCG Scalar “BM” series marine antennas.

BM6-27 Â stands 2 metres tall.BM8-27 Â is 2.5 metres tall.

Construction consists of copper radiators fully sealed inside a single piece white fibreglass radome ensuring long term survival in the harsh marine environment. The end fed half wave design provides excellent performance.

4.5 metres of RG58 low loss stranded cable side exits from the folding base. Cut the cable to the shortest length necessary prior to fitting the UHF Male solder connector provided.

The MM1 folding deck mount supplied is constructed from toughened plastic. This base folds down in two directions and also swivels in the opposite plane by loosening the stainless steel pivot bolt. This versatility allows the antenna to be mounted in a variety of positions on any flat surface and at any angle using four screws or bolts.

The antenna must be in a vertical position for optimum performance and can be folded down flat when not required.


The MM1 folding deck mount supplied is constructed from toughened plastic.

Construction

SPECIFICATIONS

Frequency

Copper internals, single piece white fibreglass radome, white delrin ferrule 1"–14 UNS female thread, MM1 base


BM6-27

GainMax Input Power

2.1 dBi


25 Watts

BM8-27

2.1 dBi25 Watts

Tuning Factory



50 Ohms

360O OmnidirectionalCable 4.5 metres RG58 low loss stranded cable side exits baseConnector UHF Male solder connector supplied, not fitted (PL259)Height (inc mount) 2.0 metres 2.5 metresWeight (inc mount) 1 kg 1.5 kg

Folding Deck Mount Base Supplied MM1 MM1

These antennas are identical in appearance to :

BM6-VHF, BM8-VHF

BM6-DB, BM8-DB

BM6-AM/FM, BM8-AM/FM

VHF 156-162 MHz

Mobile Phone

Radio Receive

ZM312H27.88 MHz Marine Radio

White Whip and Base


MARINEANTENNAS

Section 6


Standing 66 cm tall, ZM312H is a wire wound fibreglass whip with white heatshrink cover factory tuned for 27.88 MHz marine radio communications. The whip mounts onto the white OB-3 base supplied which has stainless steel and brass components to ensure long term service in the harsh marine environment.

The antenna is not ground independent and therefore must be mounted on a metallic surface at least 0.5 metres square for effective performance. Typical mount positions would be on the deck or cabin of an aluminium or steel boat.

5 metres of white RG58 low loss stranded cable bottom exits from the OB-3 antenna base. An FME female connector is fitted to the cable for easy installation.

An FME male to UHF male adaptor is also included in the kit to provide another common connector option.

ZW312H is the white top whip alone which can be ordered seperately.

Wire wound fibreglass whip, white heatshrink cover, chrome plated brass ferrule, 5/16”–26 TPI thread, white OB-3 mounting base with stainless steel and copper components

Construction

SPECIFICATIONS

Frequency 27.88 MHz Marine Radio

ZM312H

GainMax Input Power

2.1 dBi


25 Watts

Tuning Factory



Cable 5 metres of white RG58 low loss stranded cablebottom exits from the OB-3 mounting base

Connector FME female connector fitted to the cable, andFME male to UHF male adaptor supplied

Height 66 cm including the mount baseWeight 350 grams

Mounting Must be mounted to a metallic surface at least 0.5 metres square for effective performance

Replacement top whip only

Ground Independent No

ZW312H (64 cm)

B20G and B20G-NVHF Marine



MARINEANTENNAS

Section 6


Frequency Bandwidth156 – 162 MHz Full Band

Tuned to cover the full VHF Marine Band 156 to 162 MHz, these ground independent antennas may be mounted to the mast of a vessel, or they can be side mounted from a wheelhouse or any other flat vertical surface.

The white fibreglass tapered radome and stainless steel mount tube stands 3.4 metres tall.

B20G Â has a 4.5 metre RG58 stranded cable tail with a UHF Male connector supplied, not fitted.

B20G-N Â has an N-Female connector located at the base of the stainless steel mount tube.

Both models deliver 5.1 dBi gain and are rated for up to 50 watts input power.

All components used in construction are of the highest quality. Brass internals are silver soldered to ensure long term survival in the harsh marine environment. These antennas will deliver reliable performance for many years.


Construction

SPECIFICATIONS

Frequency

Single piece white fibreglass radome, silver soldered brass internals and stainless steel mount tube

VHF 156 to 162 MHz Full Band

B20G

GainMax Input Power

5.1 dBi

Impedance

Polarisation Vertical

50 Watts

Height 3.4 metresWeight 1.5 kg


2 x EB1SS stainless steel parallel clamps recommended.Suit round mast between 20 mm and 50 mm in diameter.

Mount Tube DImensions


B20G-N

5.1 dBi50 Watts

Tuning Factory

Vertical

1.5 kg



2 x NSM-CL3642 will suit the 32 mm mount tube


50 Ohms 50 OhmsDC Grounded Yes Yes

H-Plane 360O Omnidirectional 360O OmnidirectionalCable Tail 4.5 metres RG58 stranded None

Connector UHF Male solder connector supplied, not fitted (PL259)

N-Female connector at base of mount tube

3.4 metres




Using two (2) of these nylon side mounts, the antenna mount tube is held tightly by the 8 mm stainless steel clamp bolt.NSM-CL3642


clamps

CM156 and B20G/DVHF MarineDeck Mount


MARINEANTENNAS

Section 6

Updated 1 April 2011

Tuned to cover the full VHF Marine Band 156 to 162 MHz, these ground independent deck mount antennas are a single piece construction and match the height and appearance of other models in the marine range.

CM156 Â stands 2.2 metres tall and delivers 2.1 dBi gain.

B20G/D Â is taller at 2.5 metres and offers a higher 5.1 dBi gain.






Construction

SPECIFICATIONS

Frequency

Single piece white fibreglass tapered radome, chromed brass ferrule with 1"–14 UNS female thread

VHF 156 to 162 MHz Full Band

CM156, CM156SS

GainMax Input Power

2.1 dBi


50 Watts

B20G/D, B20G/DSS

5.1 dBi50 Watts

Tuning Factory



50 Ohms

360O OmnidirectionalCable 4.5 metres of RG58 stranded cable side exits from the ferruleConnector UHF Male solder connector supplied, not fitted (PL259)Height (inc mount) 2.2 metres 2.5 metresWeight (inc mount) 1 kg, 1.75 kg 1.1 kg, 1.85 kg


MM1 with CM156MM2 with CM156SS

MM1 with B20G/DMM2 with B20G/DSS





BM6-VHF and BM8-VHFVHF MarineDeck Mount


MARINEANTENNAS

Section 6


Ground independent and factory tuned to cover the full VHF Marine Band 156 to 162 MHz, these deck mount antennas are a perfect match in both height and appearance to other ZCG Scalar “BM” series marine antennas.

BM6-VHF Â stands 2 metres tall.

BM8-VHF Â is 2.5 metres tall.

Both VHF deck mount models are rated for up to 25 watts input power.

Construction consists of copper radiators fully sealed inside a single piece white fibreglass radome ensuring long term survival in the harsh marine environment. The end fed half wave design provides excellent performance.

4.5 metres of RG58 low loss stranded cable side exits from the folding base. Cut the cable to the shortest length necessary prior to fitting the UHF Male solder connector provided.




Frequency Bandwidth156 – 162 MHz FULL BAND


Construction

SPECIFICATIONS

Frequency

Copper internals, single piece white fibreglass radome, white delrin ferrule 1"–14 UNS female thread, MM1 base

VHF Marine 156 to 162 MHz Full Band

BM6-VHF

GainMax Input Power

2.1 dBi


25 Watts

BM8-VHF

2.1 dBi25 Watts

Tuning Factory



50 Ohms

360O OmnidirectionalCable 4.5 metres RG58 low loss stranded cable side exits baseConnector UHF Male solder connector supplied, not fitted (PL259)Height (inc mount) 2.0 metres 2.5 metresWeight (inc mount) 1 kg 1.5 kg



BM6-27, BM8-27

BM6-DB, BM8-DB


27 MHz Marine

Mobile Phone

Radio Receive


ZM312VVHF Marine

White Whip and Base


MARINEANTENNAS

Section 6

Updated 10 May 2011

Standing 47 cm tall, ZM312V is a wire wound fibreglass whip with white heatshrink cover and factory tuned for VHF marine communications across the 156 to 162 MHz band. The whip mounts onto the white OB-3 base supplied which has stainless steel and brass components to ensure long term service in the harsh marine environment.


5 metres of white RG58 low loss stranded cable bottom exits from the OB-3 antenna base and an FME female connector is fitted to the cable for easy installation.

An FME male to UHF male adaptor is also included in the kit to provide another common connector option.

ZW312V is the white top whip alone which can be ordered seperately.


Construction

SPECIFICATIONS

Frequency VHF 156 – 162 MHz full band

ZM312V

GainMax Input Power

2.1 dBi


25 Watts

Tuning Factory




Connector FME female connector fitted to the cable, andFME male to UHF male adaptor supplied

Height 47 cm including the mount baseWeight 350 grams




ZW312V (45 cm)

CLU3SSUHF Marine

Collinear Mast Mount


MARINEANTENNAS

Section 6


1.7 metres tall with 5.1 dBi gain, the CLU3SS marine mast mount collinear antenna can be manufactured to cover any 1.5% bandwidth you specify within the UHF frequency range 400 to 520 MHz.

The antenna is constructed from stainless steel and fibreglass to ensure long term survival in the harsh marine environment and will deliver reliable performance for many years.

The N-Female connector located at the base of the mount tube is rated for up to 100 watts input power.

Mast mounting clamps, feeder cable, connectors, cable ties and tape are available separately to complete the installation.


clamps

Frequency Bandwidth400 – 520 MHz Any 1.5%

SPECIFICATIONS CLU3SS

Frequency Range


Tuning

Polarisation

HeightWeight

MAST Mounting Clamps(Not supplied,order separate)

Gain

Construction

400 to 520 MHz


Factory

Vertical

1.7 metres1.2 kg

2 x EB1SS stainless steel parallel clamps are recommended.Suit round mast between 20 mm and 50 mm in diameter.

Single piece white fibreglass radome and stainless steel mount tube

VSWR Better than 1.5:1 across the 1.5% bandwidth specified

H-Plane 360O OmnidirectionalConnector N-Female at base of mount tube


Bandwidth Any 1.5%, specify your centre frequency when ordering

DC Grounding Yes

E-Plane 28O

Projected Area 0.032 m2

Wind Load 160 kph 3.9 kg, 0.039 kN

MA675 and MA400UHF MarineDeck Mount


MARINEANTENNAS

Section 6


These ground independent UHF marine deck mount antennas are a single piece construction and stand 2.2 metres tall, identical to other models in the marine range. The internal radiator is copper and the end fed half wave design provides excellent performance with 8.1 dBi gain.

MA675 Â is factory tuned for 477 MHz UHF CB Radio communications. This model is held in stock.

MA400 Â can be manufactured to cover any 1.5% bandwidth you specify within the UHF frequency range 400 to 520 MHz.







Frequency Bandwidth400 – 520 MHz See Below



Construction

SPECIFICATIONS

Frequency and Bandwidth

Single piece white fibreglass tapered radome, copper internal radiator, chromed brass ferrule with 1"–14 UNS female thread

477 MHz UHF CB

MA675, MA675SS

GainMax Input Power

8.1 dBi


50 Watts

MA400, MA400SS

8.1 dBi50 Watts

Tuning Factory


FactoryVSWR Better than 1.5:1 Better than 1.5:1 across 1.5%

50 Ohms

360O OmnidirectionalCable 4.5 metres of RG58 stranded cable side exits from the ferruleConnector UHF Male solder connector supplied, not fitted (PL259)Height (inc mount) 2.2 metres 2.2 metresWeight (inc mount) 1 kg, 1.75 kg 1 kg, 1.75 kg


MM1 with MA675MM2 with MA675SS

MM1 with MA400MM2 with MA400SS

Any 1.5% in UHF range 400 to 520 MHz, specify centre

CM162AISAutomatic Identification System

Marine VHF Deck Mount

Frequency


MARINEANTENNAS

Section 6

Updated 27 March 2012

Bandwidth161.9 – 162.1 MHz AIS Band

CM162AIS is a marine deck mount antenna factory tuned for the AIS Automatic Identification System operating in the VHF frequency range 161.9 to 162.1 MHz.The single piece white fibreglass radome stands 1.4 metres tall and the antenna delivers 2.1 dBi gain. 300 mm of white RG58 low loss cable side exits from the folding deck mount base and an N-Type Female connector is fitted to the cable for easy installation.The marine AIS Automatic Identification System is a Very High Frequency (VHF) radio broadcasting system that transfers packets of data over the VHF data link (VDL) and enables AIS equipped vessels and shore-based stations to send and receive identification information that can be displayed on an electronic chart, computer display or compatible radar. This information can help in situational awareness and provide a means to assist in collision avoidance. AIS can be used as an aid to navigation by providing location and additional information on buoys and lights.The AIS Class A system is mandatory for vessels over 300 gross tonnage, whereas Class B has been developed for vessels such as work craft and pleasure craft with limited functionality. This deck mount antenna is factory tuned to operate with both AIS Class A and Class B systems. There are two models to choose from.

Â CM162AIS is the standard model with white delrin ferrule and MM1 folding deck mount constructed from toughened plastic. This base folds down in two directions and also swivels in the opposite plane by loosening the stainless steel pivot bolt. This versatility allows the antenna to be mounted in a variety of positions on any flat surface and at any angle using four screws or bolts.

Â CM162AIS-SS has a chromed brass ferrule and the MM2 stainless steel folding deck mount base for those who prefer the ultimate in quality, durability and strength.


An N-Type Female connector is fitted to the cable for easy installation.



Radome

SPECIFICATIONS

Frequency

Single piece white fibreglass tapered radome

161.9 to 162.1 MHz AIS Automatic Identification System

CM162AIS

GainMax Input Power

2.1 dBi


50 Watts

CM162AIS-SS

Tuning Factory



Cable 300 mm of White RG58 low loss cable side exitsConnector N-Type Female connector fittedHeight (inc mount) 1.4 metresWeight (inc mount) 900 grams


MM1Toughened plastic

MM2Stainless steel

1.65 kg1.4 metres

White delrin Chromed brassMount Ferrule

CM Series NEXT G or GSMCellular Mobile Phone



MARINEANTENNAS

Section 6


Frequency Bandwidth825 – 960 MHz NEXT G or GSM

These ground independent omnidirectional cellular mobile phone antennas may be mounted to the mast of a vessel, or they can be side mounted from a wheelhouse or any other flat vertical surface. With 8.1 dBi gain, they offer the maximum gain and reception range practical in a broadband mobile phone antenna.

The white fibreglass radome and stainless steel mount tube stands 2.4 metres tall. The antenna is matched internally by a unique transforming printed circuit board.

The N-Female connector located at the base of the mount tube is rated for up to 20 watts input power.

CM1600AM Â is factory tuned to cover the NEXT G network.

CMG1600AM Â is for the GSM network.





Using two (2) of these nylon side mounts, the antenna mount tube is held tightly by the 8 mm stainless steel clamp bolt.NSM-B20M


clamps

Construction

SPECIFICATIONS

Cellular Mobile Phone Network Coverage

Single piece white fibreglass tapered radome, transforming printed circuit board, stainless steel mount tube

NEXT G825 – 890 MHz

CM1600AM

GainMax Input Power

8.1 dBi

Impedance

Polarisation Vertical

20 Watts


MAST Mounting Clamps (not supplied)

2 x EB1SS stainless steel parallel clamps recommended.Suit round mast between 20 mm and 50 mm in diameter.


CMG1600AM

8.1 dBi20 Watts

Tuning Factory

Vertical

0.7 kg

SIDE Mounting Clamps (not supplied) 2 x NSM-B20M will suit the 20 mm mount tube


50 Ohms 50 OhmsDC Grounded Yes Yes

H-Plane 360O Omnidirectional 360O OmnidirectionalConnector N-Female located at base of mount tube

2.4 metres

Blue Cap Red Cap

GSM890 – 960 MHz

E-Plane 13O 13O

AN1600 and DG1600 MAX-GAINNEXT G or GSM Cellular Mobile Phone

Deck Mount


MARINEANTENNAS

Section 6

Updated 24 July 2012

With 8.1 dBi gain, these marine deck mount models offer the maximum gain and reception range practical in a broadband cellular mobile phone antenna.The single piece white fibreglass radome stands 2.2 metres tall, identical to other models in the marine range. These antenna are matched internally by a unique transforming printed circuit board.

Â AN1600 is factory tuned to cover the NEXT G network. Â DG1600 is for the GSM network.

5 metres of RG58 low loss cable side exits from the chromed brass ferrule. An FME Female crimp connector is fitted to the cable.





An FME Female crimp connector is fitted to the 5 metre RG58 low loss cable.

Frequency Bandwidth825 – 960 MHz NEXT G or GSM



Construction

SPECIFICATIONS


Single piece white fibreglass tapered radome, transforming printed circuit board, chromed brass ferrule

NEXT G825 – 890 MHz

AN1600, AN1600SS

GainMax Input Power

8.1 dBi


30 Watts

DG1600, DG1600SS

8.1 dBi30 Watts

Tuning Factory

Vertical

E-Plane 360O Omnidirectional


50 Ohms

360O OmnidirectionalCable 5 metres of RG58 low loss cable side exits from the ferruleConnector FME Female crimp connector fitted to the cableHeight (inc mount) 2.2 metres 2.2 metresWeight (inc mount) 1 kg, 1.75 kg 1 kg, 1.75 kg


MM1 with AN1600MM2 with AN1600SS

MM1 with DG1600MM2 with DG1600SS

GSM890 – 960 MHz

H-Plane 13O 13O

MADB Multiband NEXT G and GSM Cellular Mobile Phone

Deck Mount


MARINEANTENNAS

Section 6

Updated 30 November 2011

The MADB marine deck mount cellular mobile phone antenna provides multiband coverage of both NEXT G and GSM networks combined with an effective 6.2 dBi gain. No metal ground plane is necessary.

Standing 90 cm tall, the fibreglass radome is available in 3 colours; White, Black or Brown. Specify your preference when ordering.

The MM1 folding deck mount supplied as standard is constructed from toughened plastic. This base folds down in two directions and also swivels in the opposite plane by loosening the stainless steel pivot bolt.

This versatility makes the MADB model a perfect choice for mounting to both recreational and commercial vessels alike on any flat surface and at any angle desired using four screws or bolts. The antenna can be folded down flat while not in use.

5 metres of RG58 low loss stranded cable side exits from the mount ferrule. The FME female connector fitted to the cable is rated for up to 30 watts input power.

This MADB model is identical in appearance to the MA1100 antenna for AM/FM radio receive.

For those who prefer the ultimate in quality, durability and strength, the antenna is also available with the MM2 folding deck mount which is constructed entirely from stainless steel. The order code is MADBSS.


For those who prefer the ultimate in quality, durability and strength, the MM2 folding deck mount is constructed entirely from stainless steel. This MM2 base is supplied with the MADBSS model.

An FME female connector is fitted to the cable.

This antenna is usually mounted to the deck of a marine vessel. However, the folding swivel base is also perfectly suited for mounting to a caravan, motor home, trailer, outside on the facia board of a building or any flat surface whatsoever.

SPECIFICATIONS MADB



Tuning

Polarisation

Height (inc mount)Weight (inc mount)

Gain

Construction

NEXT G and GSM combined825 to 960 MHz and 1710 to 2190 MHz

30 Watts50 Ohms

Factory

Vertical

90 cm0.8 kg

Fibreglass radome, copper radiating elements, aluminium ferrule, delrin adaptor for base

VSWR Less than 1.6:1 across the full band


Connector An FME female connector is fitted to the cable

Cable 5 metres of RG58 low loss stranded cable side exits from the aluminium ferrule

Radome Colour Specify either a White, Black or Brown radome colour when ordering

Folding Base Supplied

Secure the folding base to any flat surface at any angle using 4 screws or boltsMounting

MM1toughened plastic

MM2stainless steel

MADBSS

1.55 kg90 cm

Factory

30 Watts50 OhmsVertical360O Omnidirectional

6.2 dBi at 825 to 960 MHz3 dBi at 1710 to 2190 MHz

Frequency Bandwidth825 – 960 MHz

1710 - 2190 MHzNEXT G and GSM

combined

BM6-DB and BM8-DB MultibandNEXT G and GSM Cellular Mobile Phone

Deck Mount


MARINEANTENNAS

Section 6


Ground independent and factory tuned to provide multiband coverage of both the NEXT G and GSM cellular mobile phone networks combined with 6.2 dBi gain, these deck mount antennas are a perfect match in both height and appearance to other ZCG Scalar “BM” series marine antennas.

BM6-DB Â stands 2 metres tall.BM8-DB Â is 2.5 metres tall.

Construction consists of brass radiators fully sealed inside a single piece white fibreglass radome ensuring long term survival in the harsh marine environment.

4.5 metres of RG58 low loss stranded cable side exits from the folding base. An FME Female connector is fitted to the cable.



Frequency Bandwidth825 – 960 MHz NEXT G and GSM combined


Construction

SPECIFICATIONS


Brass internals, single piece white fibreglass radome, white delrin ferrule 1"–14 UNS female thread, MM1 base

NEXT G and GSM combined, 825 to 960 MHz full band

BM6-DB

GainMax Input Power

6.2 dBi


30 Watts

BM8-DB

6.2 dBi30 Watts

Tuning Factory


FactoryVSWR Better than 2:1 Better than 2:1

50 Ohms

360O OmnidirectionalCable 4.5 metres RG58 low loss stranded cable side exits baseConnector An FME Female connector is fitted to the cableHeight (inc mount) 2.0 metres 2.5 metresWeight (inc mount) 1 kg 1.5 kg


An FME Female connector is fitted to the 4.5 metre RG58 low loss stranded cable.


BM6-27, BM8-27

BM6-VHF, BM8-VHF


27 MHz Marine

VHF 156-162 MHz

Radio Receive

B20G-N-AMFMAM/FM Radio Receive



MARINEANTENNAS

Section 6


Frequency Bandwidth530 KHz – 108 MHz AM and FM Radio

To boost AM and FM radio reception while at sea, the B20G-N-AMFM ground independent mast mount antenna offers superb performance. Alternatively, it can be side mounted from a wheelhouse or some other flat vertical surface.

The white fibreglass tapered radome and stainless steel mount tube stands 3.4 metres tall. An N-female connector is located at the base of the mount tube.

All components used in construction are of the highest quality to ensure the antenna will survive in the harsh marine environment for many years.

The B20G-N mast mount model for VHF 156 to 162 MHz is identical in appearance.




Using two (2) of these nylon side mounts, the antenna mount tube is held tightly by the 8 mm stainless steel clamp bolt.NSM-CL3642


clamps

Construction

SPECIFICATIONS

Frequency

Single piece white fibreglass radome, stainless steel mount tube

AM Radio 530–1600 KHz, FM Radio 88–108 MHz

B20G-N-AMFM

Gain Receive OnlyImpedancePolarisation Vertical



2 x EB1SS stainless steel parallel clamps recommended, suit round mast between 20 mm and 50 mm in diameter

Mount Tube DImensions 500 mm long x 32 mm diameter

Tuning Factory



50 Ohms

H-Plane 360O OmnidirectionalCable None supplied, available separatelyConnector N-female at base of mount tube

AM80 and B20G/D-AMFMAM/FM Radio Receive

Deck Mount


MARINEANTENNAS

Section 6

Updated 31 May 2011

Tuned to receive AM and FM radio broadcasts while at sea, these marine deck mount antennas are a single piece construction and match the height and appearance of other models in the marine range.

AM80 Â stands 2.2 metres tall.B20G/D-AMFM Â is taller at 2.5 metres.

These antennas contain a tuned section to provide strong resonance at 100 MHz to pull in the normally weaker FM radio signals.

4.5 metres of RG58 cable side exits from the chromed brass ferrule. Cut the cable to the shortest length necessary prior to fitting the solderless car radio connector supplied.








Construction

SPECIFICATIONS

Frequency

Single piece white fibreglass tapered radome, chromed brass ferrule with 1"–14 UNS female thread


AM80, AM80SS

Gain Receive onlyImpedance 50 OhmsPolarisation Vertical

B20G/D-AMFM, B20G/D-AMFMSS

Tuning Factory


Factory

50 Ohms

360O OmnidirectionalCable 4.5 metres of RG58 low loss stranded cable side exitsConnector Solderless “easy fit” car radio connector suppliedHeight (inc mount) 2.2 metres 2.5 metresWeight (inc mount) 1 kg, 1.75 kg 1.1 kg, 1.85 kg


MM1 with AM80MM2 with AM80SS

MM1 with B20G/D-AMFMMM2 with B20G/D-AMFMSS

Receive only

An “easy fit” solderless car radio connector is supplied.

MA1100AM/FM Radio Receive

Deck Mount


MARINEANTENNAS

Section 6


The MA1100 marine deck mount antenna will significantly improve your AM and FM radio reception while at sea. No metal ground plane is necessary for effective performance.

Standing 90 cm tall, the MM1 folding deck mount supplied as standard is constructed from toughened plastic. This base folds down in two directions and also swivels in the opposite plane by loosening the stainless steel pivot bolt.

This versatility makes the MA1100 model a perfect choice for mounting to both recreational and commercial vessels alike on any flat surface and at any angle desired using four screws or bolts. The antenna can be folded down flat while not in use.

5 metres of RG58 low loss stranded cable side exits from the mount ferrule. The cable may be cut shorter if desired, prior to fitting the solderless car radio connector supplied.

This MA1100 model is identical in appearance to the MADB Multiband NEXT G and GSM Mobile Phone antenna.

For those who prefer the ultimate in quality, durability and strength, the antenna is also available with the MM2 folding deck mount which is constructed entirely from stainless steel. The order code is MA1100SS.


An “easy fit” solderlesscar radio connector is supplied.


Frequency

SPECIFICATIONS MA1100

AM Radio 530 to 1600 KHzFM Radio 88 to 108 MHz

Receive OnlyGain50 Ohms

Factory

5 metres of RG58 low loss stranded cable side exits from the aluminium mount ferrule

A solderless car radio connector is supplied90 cm0.8 kg

Secure the folding base to any flat surface at any angle using 4 screws or bolts

Impedance

Tuning

Cable

ConnectorHeightWeight

Mounting

Construction Fibreglass radome, aluminium mount ferrule, white delrin adaptor for folding base

WhiteRadome Colour

VerticalPolarisation360O OmnidirectionalH-Plane

White

MA1100SS

MM1toughened plastic

MM2stainless steel

1.55 kg90 cm

Receive Only50 Ohms

Factory

Vertical360O Omnidirectional The MM1 folding deck mount

supplied as standard is constructed from toughened plastic.

For those who prefer the ultimate in quality, durability and strength, the MM2 folding deck mount is constructed entirely from stainless steel. This MM2 base is supplied with the MA1100SS model.

This antenna is usually mounted to the deck of a marine vessel. However, the folding swivel base is also perfectly suited for mounting to a caravan, motor home, trailer, outside on the facia board of a building or any flat surface whatsoever.

BM6-AM/FM and BM8-AM/FMAM/FM Radio Receive

Deck Mount


MARINEANTENNAS

Section 6


Factory tuned to receive AM and FM Radio broadcasts while at sea, these deck mount antennas are a perfect match in both height and appearance to other ZCG Scalar “BM” series marine antennas.

BM6-AM/FM Â stands 2 metres tall.BM8-AM/FM Â is 2.5 metres tall.

The single piece white fibreglass radome is fully sealed to protect the copper internals ensuring long term survival in the harsh marine environment. The antennas are optimised in the factory for strong resonance across both the AM and FM radio frequencies.

4.5 metres of RG58 low loss stranded cable side exits from the folding base. A solderless “easy fit” car radio connector is supplied.


The antenna must be in a vertical position for the optimum radio reception and can be folded down flat when not required.



Construction

SPECIFICATIONS

Frequency

Copper wire internals, single piece white fibreglass radome, white delrin ferrule 1"–14 UNS female thread, MM1 base

AM Radio 530 to 1600 KHz and FM Radio 88 to 108 MHz

BM6-AM/FM

Gain Receive onlyImpedance 50 OhmsPolarisation Vertical

BM8-AM/FM

Tuning Factory


Factory

50 Ohms

360O OmnidirectionalCable 4.5 metres RG58 low loss stranded cable side exits baseConnector Solderless “easy fit” car radio connector suppliedHeight (inc mount) 2.0 metres 2.5 metresWeight (inc mount) 1 kg 1.5 kg


Receive only


BM6-27, BM8-27

BM6-VHF, BM8-VHF

BM6-DB, BM8-DB

27 MHz Marine

VHF 156-162 MHz

Mobile Phone

An “easy fit” solderless car radio connector is supplied.

ZM312BAM/FM Radio ReceiveWhite Whip and Base


MARINEANTENNAS

Section 6

Updated 5 May 2011

Standing 66 cm tall, ZM312B is a wire wound fibreglass whip with white heatshrink cover factory tuned to receive AM and FM radio transmissions. The whip mounts onto the white OB-3 base supplied which has stainless steel and brass components to ensure long term service in the harsh marine environment.


5 metres of white RG58 low loss stranded cable bottom exits from the OB-3 antenna base. A car radio connector is fitted to the cable for easy installation.

ZW312B is the white top whip alone which can be ordered seperately.


Construction

SPECIFICATIONS

Frequency


ZM312B

Gain Receive OnlyImpedance 50 OhmsPolarisation Vertical

Tuning Factory



Connector Car radio connector fittedHeight 66 cm including the mount baseWeight 350 grams




ZW312B (64 cm)


Marine Antenna Mounts


MARINEANTENNAS

Section 6


Folding Deck Mount Bases

The MM1 base supplied as standard with all our marine deck mount antennas is constructed from toughened plastic. This base folds down in two directions and also swivels in the opposite plane by loosening the stainless steel pivot bolt. This versatility allows an antenna to be mounted in a variety of positions on any flat surface and at any angle desired using four screws or bolts.

The thread at the top of the base is 1"–14 UNS male to match the female thread in the ferrule of our deck mount antennas.

For those who prefer the ultimate in quality, durability and strength, the MM2 folding deck mount is constructed entirely from stainless steel. To order any of our marine deck mount antennas with the stainless steel MM2 base in place of the MM1, simply add the letters ‘SS’ to the antenna Order Code.

Please Note : These folding bases are also most useful for mounting an antenna to any flat surface whatsoever; not just on a marine vessel. Typical examples include mounting an antenna to a caravan or trailer, on a roof or vertically to the facia board of a building.

Nylon Side Mounts

Constructed from nylon with stainless steel bolts and washers, Nylon Side Mounts are specifically designed to mount a marine antenna to the side of a vessel’s wheelhouse or any other flat vertical structure.


Using two (2) of these nylon side mounts, the antenna mount tube is held tightly by the 8 mm stainless steel clamp bolt.

The radiating section of the antenna must to be elevated well clear of the mount structure, other antennas and all metallic objects to avoid interference and distortion of the 360O omnidirectional radiation pattern.

NSM223 Suit 50 mm diameter tube.

NSM/218 Suit 38 mm diameter tube.

NSM-CL3642 Suit 32 mm diameter tube.

NSM-B20M Suit 20 mm diameter tube.

Side Mount HM223/M.

Side Mount HM218/M.

Side Mount B20G, B20G-N.

Side Mount ZM108A, CM1600AM, CMG1600AM.

Mast Mounting Clamps

A variety of parallel clamps are available for mounting antennas to round masts of various diameters. Our entire range of clamps are listed in the “Antenna Mounting Accessories” section of our Product Catalogue. However, for the marine environment, this selection of parallel clamps are the most common :

EB1SSAntenna Tube : 20 to 50 mm diam.Round Mast : 20 to 50 mm diam.All stainless steel.Two (2) clamps required.

UB3SSAntenna Tube : 20 to 32 mm diam.Round Mast : 20 to 50 mm diam.All stainless steel.Single clamp sufficent for smaller antennas.

UAM180LAntenna Tube : 40 to 75 mm diam.Round Mast : 40 to 75 mm diam.Galvanised steel components.Two (2) clamps required.

MMAMast Mount Adaptor


MARINEANTENNAS

Section 6


The MMA Mast Mount Adaptor is an aluminium tube 250 mm long x 25 mm in diameter with 1"–14 UNS male thread.

Any or our ZCG Scalar Marine Deck Mount Antennas fitted with the MM1 or MM2 folding base can be very easily converted to a mast mount antenna in 3 simple steps :

Unscrew and remove the antenna top from the MM1 or MM2 deck mount base.1.

Screw the antenna top onto the aluminium 2. MMA mast mount adaptor tube.

Use 2 parallel clamps to mount the antenna to a mast. 3. EB1SS stainless steel clamps will be ideal.

This example shows EB1SS mast clamps

MMAMast Mount Adaptor

Aluminium tube 250 mm long x 25 mm diameterwith 1"–14 UNS male thread

Cable Ties and Tape


MARINEANTENNAS

Section 6


8528-1

8529

8530

Bag of 100 Black Nylon Cable Ties,100 mm long

Stainless steel cable ties offer significant benefits over the black nylon type :Superior strength. 9Ideal for use indoors, outdoors or underground. 9Resistant to corrosion, salt, acids, chemicals, radiation, extreme temperatures and all weather conditions. 9Install with full confidence that the Grade 316 Stainless Steel will maintain integrity over many decades. 9Tensioner Tool available to fit stainless steel cable ties quickly at the proper tension and neatly cut off the tail. 9

8117-2

8117-3

8117

Bag of 100 Stainless Steel Grade 316 Cable Ties, 200 mm long x 4.6 mm

8117-4

8117-5







8574

Self Bonding Amalgamating Electrical Tape,19 mm wide x 0.76 mm thick, 9.15 metre roll

8651

PVC Electrical Insulating Tape, Black,19 mm wide x 0.18 mm thick, 20 metre roll

All connections should be sealed with two layers of self-amalgamating tape to prevent ingress of moisture.

8125Stainless Steel Cable Tie

Tensioner Tool, fit ties quick, easy and neat.

marine antennas summary - westradio.com.au · marine antennas summary zcg scalar, head office, 7...

Documents