microwave installation technology nec
TRANSCRIPT
-
7/28/2019 Microwave Installation Technology Nec
1/28
Optical engineering Dep.
-
7/28/2019 Microwave Installation Technology Nec
2/28
System Components
Installation and key point
Debugging
Page 2
-
7/28/2019 Microwave Installation Technology Nec
3/28
-
7/28/2019 Microwave Installation Technology Nec
4/28
Diameter (m): 0.30.61.21.5 1.8 2.02.53.23.7
Page 4
Feed source
Parabolic refle
Mount bracket
String
-
7/28/2019 Microwave Installation Technology Nec
5/28
Page 5
Flexibl
e twistODU
Mountbracket
-
7/28/2019 Microwave Installation Technology Nec
6/28
Page 6
IDU
ODU
Antenna(0.3m)
PASOLINK
-
7/28/2019 Microwave Installation Technology Nec
7/28Page 7
-
7/28/2019 Microwave Installation Technology Nec
8/28Page 8
-
7/28/2019 Microwave Installation Technology Nec
9/28Page 9
1. IF connector (to ODU)
2. 2Mbps interface (CH 9 to CH 16): impedance selector switch (75 or 120 ohms)
3. LAN Interface for main traffic: Port 1 and Port 2 (Optional)
4. WS/LAN: optional port for Wayside In/Out or 10BaseT
5. NMS LAN: for PNMS with LAN interface
6. Engineers Orderwire (EOW): receptacle for EOW headset
7. CALL: call buzzer for calling the opposite site of the transmission path
8. RESET: CPU reset switch for IDU
1
2 3 4 5 6 7
8
-
7/28/2019 Microwave Installation Technology Nec
10/28Page 10
9. LED: PWR : that the power switch is on (Green)
MAINT: for the purpose of maintenance (Yellow)
ODU : that the ODU alarms occur (Red)
IDU : that the IDU alarms occur (Red)
10. FG : connecting Frame Ground terminal
11. ESD: Connecting terminal for Electro Static Discharge
12. 2Mbps interface (CH 1 to CH 8) ): impedance selector switch (75 or 120 ohms)
13. ALM/AUX ALM: connector for parallel alarms (relay contact)
connector for Data Input / Data Output
10 11 12 139
-
7/28/2019 Microwave Installation Technology Nec
11/28Page 11
14. OW / DSC / ASC
(1) Order wire
(2) Digital and Analog (VF) service channel
15. NMS / RA: for PNMS or remote access Local Craft Terminal (None PM Card)
16. LA Port: connector to PC for local access Local Craft Terminal or PNMT
17. Fuse: for primary DC line (be inserted in each plus and minus line)
14
18. 20SW : power switch
19. DC IN: connector for DC power in.
15 16 17 18 19
-
7/28/2019 Microwave Installation Technology Nec
12/28Page 12
Rear Side Front Side
IF connector to IDU RF interface to Antenna( PBR220)RX LEV MON
-
7/28/2019 Microwave Installation Technology Nec
13/28Page 13
-
7/28/2019 Microwave Installation Technology Nec
14/28
Page 14
-
7/28/2019 Microwave Installation Technology Nec
15/28
Page 15
-
7/28/2019 Microwave Installation Technology Nec
16/28
Page 16
PASOLINK+ IDU
1+1 System
-
7/28/2019 Microwave Installation Technology Nec
17/28
Page 17
INTFCWS(option)
LEDsMAINT ODU IDU PWR
DC IN
PNMT
NE1 NE2 LAN V11(PNMS)
ASC/DSC ALM Out
House
keeping
EXT
OWLCT
FUSE PSFUSE
CPU
Reset
PWR
SW
FUSE
R
SW
RS422(Sync/Async)
or RS485
10Base-TRS422
(Async)
RS232C
IF IN/OUT EOW
OW: 1CHDSC: 2CH(64k/V11)
ASC: 2CH(SDH) or 1CH(PDH)
IDU-IDU
IDU-ODU
ODU-ODU
WS(option)
E1/T1/10Base
Except STM-1/128Q
7 or 11 Output
6 Input
4 or O Output
150(E/OPT)Nx2MB(75/120ohm)
PASOLINK+ IDU Interface
-
7/28/2019 Microwave Installation Technology Nec
18/28
Page 18
12 3 4 5
6 7 8 9
10 11 12 13 1415 16 17
18192021222324
PASOLINK+ IDU Interface
1. IF connector (to ODU)
2. PNMT : Connect to PC for NMS
3. LCT : Connect to PC for Local Craft Terminal
4. EOW1 : Connect between IDUs for order wire
5. EOW2 : Connect between IDUs for order wire
6. NE1 : Connect between IDUs for NMS network7. NE2 : Connect between IDUs for NMS network
8. LAN : Connect between IDUs for NMS network with LAN network
9. V11 : Connect between IDUs for NMS network with V.11 network
10. SC IN/OUT : Connector for Service Channel
11. ALM connector for parallel alarms (relay contact : Form-C)
12. ALM/AUX : Connector for Data Input/Data Output for house keeping
-
7/28/2019 Microwave Installation Technology Nec
19/28
Page 19
13. R SW : Selector switch for switching b.w. previous firmware
and new download firmware
14. EOW : Receptacle for headset
15. CALL : Call buzzer for calling opposite site
16. RESET : CPU reset switch for IDU
17. LEDs :
MAINT : IDU maintenance condition
ODU : ODU alarms
IDU : IDU alarms
PWR : Power switch on
18. DC IN : Connector for DC power in
19. SW : Power switch
20. Fuse : Fuses for primary DC line
21. Interface Card : STM-1 optical/STM-1 electrical, Nx2MB(G.703)22. WS IN/OUT or 10Base-T interface card :
Select card as an option, wayside(2.048Mbps), 10 Base-T or blanc panel
23. ESD : Connecting terminal for Electro Static Discharge
24. FG : Frame Ground Terminal
-
7/28/2019 Microwave Installation Technology Nec
20/28
Water-proof
There must be a gasket at
the meeting place of the ODU and
the antenna, or the meeting place
of the ODU and the flexible twist.
Smear the water-proof glue at the
meeting place then wrap the
water-proof tape and the then
adhesive plaster at the outmost.
Page 20
Gasket cant
be lost!
Be lack of
water-proof and
plaster!
-
7/28/2019 Microwave Installation Technology Nec
21/28
Page 21
The waveguide ports must beidentical!
Dont be cross!
The polarization orientation must be
identical in one hop!
-
7/28/2019 Microwave Installation Technology Nec
22/28
Page 22
Cable ought to superfluous.
Water-proof
Ground line must be
connected!
-
7/28/2019 Microwave Installation Technology Nec
23/28
Page 23
Cables ground line must be connected!
-
7/28/2019 Microwave Installation Technology Nec
24/28
Page 24
There must betwo nuts fixed!
This is
unqualified!
-
7/28/2019 Microwave Installation Technology Nec
25/28
Page 25
High site and Low site are forbidden in one station!
-
7/28/2019 Microwave Installation Technology Nec
26/28
Two terminals ought to be open!
The adjusting line will be connected ODUs MON
port with multimeter.
Adjust multimeter to DVC 10 volt position.
The multimeters display is bigger, the Rx power
(Rx voltage) is better!
During adjusting, one terminal is carrying on,
another terminal must be quiet!
Page 26
Rx LEV
MON
Special adjusting line
-
7/28/2019 Microwave Installation Technology Nec
27/28
During the adjusting course,
two cases are wrong:
one terminals side-lobe
meet another terminals
side-lobe; one terminals
side-lobe meet another
terminals main-lobe!
The only right case is that:
one terminals main-lobe
meet another terminalsmain-lobe!
Page 27
wrong wrong right
-
7/28/2019 Microwave Installation Technology Nec
28/28
P 28
Rx power
Antenna moving orientation
The multimeter displaying