mobile sources. mobile sources gasoline car: 4-strokes diesel car automobile : 4-strokes, 2-strokes

Click here to load reader

Post on 15-Dec-2015




0 download

Embed Size (px)


  • Slide 1

Mobile Sources Slide 2 Mobile sources Gasoline car: 4-strokes Diesel car Automobile : 4-strokes, 2-strokes Slide 3 Animated scheme of a four stroke internal combustion engine, Otto principle: Intake stroke - Air and vaporized fuel are drawn in. Compression stroke - Fuel vapor and air are compressed and ignited. Power stroke - Fuel combusts and piston is pushed downwards. Exhaust stroke - Exhaust is driven out. Slide 4 The primary difference between carburetors and fuel injection is that fuel injection atomizes the fuel by forcibly pumping it through a small nozzle under high pressure, while a carburetor relies on suction created by intake air accelerated through a Venturi tube to draw the fuel into the airstream. To more easily comply with emissions regulations, automobile manufacturers began installing fuel injection systems in more gasoline engines during the late 1970s. Since the early 1990s, almost all gasoline passenger cars sold in first world markets are equipped with electronic fuel injection (EFI). The carburetor remains in use in developing countries where vehicle emissions are unregulated and diagnostic and repair infrastructure is sparse. Fuel injection is gradually replacing carburetors in these nations too as they adopt emission regulations conceptually similar to those in force in Europe, Japan, Australia and North America. Source: Slide 5 In order to meet stricter emissions requirements, catalytic converters were introduced. Very careful control of the air-to-fuel ratio was required for the catalytic converter to be effective. Oxygen sensors monitor the amount of oxygen in the exhaust, and the engine control unit (ECU) uses this information to adjust the air-to-fuel ratio in real-time. This is called closed loop control -- it was not feasible to achieve this control with carburetors. When you step on the gas pedal, the throttle valve opens up more, letting in more air. The engine control unit (ECU, the computer that controls all of the electronic components on your engine) "sees" the throttle valve open and increases the fuel rate in anticipation of more air entering the engine. It is important to increase the fuel rate as soon as the throttle valve opens; otherwise, when the gas pedal is first pressed, there may be a hesitation as some air reaches the cylinders without enough fuel in it. Sensors monitor the mass of air entering the engine, as well as the amount of oxygen in the exhaust. The ECU uses this information to fine-tune the fuel delivery so that the air-to-fuel ratio is just right. Slide 6 Emissions and Emission Sources of Light-Duty Vehicles. Slide 7 These main areas of emissions are classified as evaporative, exhaust, and refueling losses. Evaporation of gasoline is a source of volatile organic compounds (VOCs) comparable in magnitude to the exhaust VOCs emissions. The four categories of evaporative volatile organic compounds emissions from motor vehicle fuel systems are: (1) diurnal emissions, (2) running losses, (3) hot soak emissions and (4) refueling. Diurnal emissions occur due to evaporation of gasoline, which increases as the temperature rises during the day, heating the fuel tank and venting its vapor. Running losses occur as the gasoline vapors are vented from the fuel tank while the automobile is operating and the fuel in the tank becomes hot. Hot soak emissions are released when the engine is turned off after operation and remains hot for a period of time after, which the gasoline continuing to evaporate until the engine reaches ambient temperatures. Slide 8 Stage II Gasoline Vapor Recovery System Slide 9 Basic Controls for SI Engine Exhaust and Evaporative Emissions Slide 10 Slide 11 Slide 12 Reformulated Gasoline (RFG) The cleaner burning gasoline is called reformulated gasoline or RFG. MTBE (methyl tertiary butyl ether, , CH 3 OC(CH 3 ) 3 ) and ethanol ( ,CH 3 CH 2 OH) are the two most commonly used oxygenates that increase oxygen content to gasoline for more complete combustion in engines. In some areas of the United States, ethanol is blended with gasoline to form an E10 blend (10% ethanol and 90% gasoline), but it can be used in higher concentrations such as E85 or E95. Slide 13 MTBE Many chemicals in gasolineincluding MTBEcan be harmful in water. MTBE is highly soluble and travels faster and farther in water than other gasoline components. Slide 14 Summary Table of Alternative Fuel Advantages and Disadvantages Slide 15 Slide 16 Diesel Engines Diesel PM consists of three primary constituents: unburned carbon particles, which make up the largest portion of the total PM; the soluble organic fraction (SOF), which consists of unburned hydrocarbons that have condensed into liquid droplets or have condensed onto unburned carbon particles; and sulfates, which result from oxidation of fuel-borne sulfur in the engines exhaust. Diesel engines have made great progress in lowering engine out emissions by improving diesel combustion and fuel systems. (electronic fuel systems, increasing fuel injection pressures) exhaust gas recirculation (EGR). Particulate filters, or traps. the diesel oxidation catalyst (DOC) Slide 17 At the time, typical new cars were emitting nearly 13 grams per mile hydrocarbons (HC), 3.6 grams per mile nitrogen oxides (NOx), and 87 grams per mile carbon monoxide (CO). The current Federal certification standards for exhaust emissions from cars are 0.25 gram per mile HC, 0.4 gram per mile NOx, and 3.4 grams per mile CO.