USP supplies quality productsto build Stronger Safer Structures

USPconnectors.com

Use in conjunction with USP’s current Canadian Product Catalogue for detailed hanger information.

Field adjustable framing angle from 0° to 135°.

Materials: 18 gaugeFinish: G90 galvanizingOptions: See current catalogue for Corrosion Finish Options.Codes: Factored resistances are derived from data submitted to various North American building code evaluators.

Installation:• Use all specified fasteners. • MP Framing Angles are fabricated at 100° and may be field adjusted by hand from 0° to 135°. Bend angle only once.

MP Framing Angle

Typical MPinstallation

MP

Typical MPrafter support installation

Qty Type Qty Type 100% 115% 100% 115% 100% 115% 100% 115% MP3 3-3/8 3 10d 3 10d 715 715 3.18 3.18 610 610 2.71 2.71 MP5 4-5/8 4 10d 4 10d 1010 1010 4.49 4.49 865 865 3.85 3.85 MP7 5-7/8 5 10d 5 10d 1315 1315 5.85 5.85 1125 1125 5.00 5.00 MP9 6-7/8 6 10d 6 10d 1410 1410 6.27 6.27 1210 1210 5.38 5.38

1) Factored resistances are shown per angle, and may be doubled if installed in pairs. When using a single angle, joist must be constrained from rotation. 2) For 1-1/2" lumber where 10d nails are specified, use 10d x 1-1/2" nails and apply 0.90 adjustment factor to the table value. 3) NAILS: 10d nails are 0.148" dia. x 3" long.

F1 (Lbs)F1 (kN)USPStock No.

S-P-F Factored Resistance1

L(in)

F1 (Lbs)

Fastener Schedule2,3

Header Joist

DF Factored Resistance1

F1 (kN)

©2016 MiTek Industries, Inc. All Rights Reserved. Revised November 2016 USP2320-MP

F1

USP supplies quality productsto build Stronger Safer Structures

USPconnectors.com

Use in conjunction with USP’s current Canadian Product Catalogue for detailed hanger information.

Field adjustable framing angle from 0° to 135°.

Materials: 18 gaugeFinish: G90 galvanizingOptions: See current catalogue for Corrosion Finish Options.Codes: Factored resistances are derived from data submitted to various North American building code evaluators.

Installation:• Use all specified fasteners. • MP Framing Angles are fabricated at 100° and may be field adjusted by hand from 0° to 135°. Bend angle only once.

MP Framing Angle

Typical MPinstallation

MP

Typical MPrafter support installation

Qty Type Qty Type 100% 115% 100% 115% 100% 115% 100% 115% MP3 3-3/8 3 10d 3 10d 715 715 3.18 3.18 610 610 2.71 2.71 MP5 4-5/8 4 10d 4 10d 1010 1010 4.49 4.49 865 865 3.85 3.85 MP7 5-7/8 5 10d 5 10d 1315 1315 5.85 5.85 1125 1125 5.00 5.00 MP9 6-7/8 6 10d 6 10d 1410 1410 6.27 6.27 1210 1210 5.38 5.38

1) Factored resistances are shown per angle, and may be doubled if installed in pairs. When using a single angle, joist must be constrained from rotation. 2) For 1-1/2" lumber where 10d nails are specified, use 10d x 1-1/2" nails and apply 0.90 adjustment factor to the table value. 3) NAILS: 10d nails are 0.148" dia. x 3" long.

F1 (Lbs)F1 (kN)USPStock No.

S-P-F Factored Resistance1

L(in)

F1 (Lbs)

Fastener Schedule2,3

Header Joist

DF Factored Resistance1

F1 (kN)

©2016 MiTek Industries, Inc. All Rights Reserved. Revised November 2016 USP2320-MP

F1

USP supplies quality productsto build Stronger Safer Structures

USPconnectors.com

Use in conjunction with USP’s current Canadian Product Catalogue for detailed hanger information.

Field adjustable framing angle from 0° to 135°.

Materials: 18 gaugeFinish: G90 galvanizingOptions: See current catalogue for Corrosion Finish Options.Codes: Factored resistances are derived from data submitted to various North American building code evaluators.

Installation:• Use all specified fasteners. • MP Framing Angles are fabricated at 100° and may be field adjusted by hand from 0° to 135°. Bend angle only once.

MP Framing Angle

Typical MPinstallation

MP

Typical MPrafter support installation

Qty Type Qty Type 100% 115% 100% 115% 100% 115% 100% 115% MP3 3-3/8 3 10d 3 10d 715 715 3.18 3.18 610 610 2.71 2.71 MP5 4-5/8 4 10d 4 10d 1010 1010 4.49 4.49 865 865 3.85 3.85 MP7 5-7/8 5 10d 5 10d 1315 1315 5.85 5.85 1125 1125 5.00 5.00 MP9 6-7/8 6 10d 6 10d 1410 1410 6.27 6.27 1210 1210 5.38 5.38

1) Factored resistances are shown per angle, and may be doubled if installed in pairs. When using a single angle, joist must be constrained from rotation. 2) For 1-1/2" lumber where 10d nails are specified, use 10d x 1-1/2" nails and apply 0.90 adjustment factor to the table value. 3) NAILS: 10d nails are 0.148" dia. x 3" long.

F1 (Lbs)F1 (kN)USPStock No.

S-P-F Factored Resistance1

L(in)

F1 (Lbs)

Fastener Schedule2,3

Header Joist

DF Factored Resistance1

F1 (kN)

©2016 MiTek Industries, Inc. All Rights Reserved. Revised November 2016 USP2320-MP

F1